When runtime PM is enabled, regulators are being controlled by the
driver's suspend and resume callbacks. They are also unconditionally
enabled at driver's probe(), and disabled in remove() functions. Add
more calls to runtime PM framework to ensure that the device's runtime
PM state matches the regulators state:
1. at the end of probe() function: set runtime PM state to active, so
there will be no spurious call to resume();
2. in remove(), ensure that resume() is called before disabling runtime PM
management and unconditionally disabling the regulators.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
WM8994 chip has built-in regulators, which might be used for chip
operation. They are controlled by a separate wm8994-regulator driver,
which should be loaded before this driver calls regulator_get(), because
that driver also provides consumer-supply mapping for the them. If that
driver is not yet loaded, regulator core substitute them with dummy
regulator, what breaks chip operation, because the built-in regulators are
never enabled. Fix this by annotating this driver with MODULE_SOFTDEP()
"pre" dependency to "wm8994_regulator" module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The spi_register_driver() will set the spi_bus_type for the spi_driver,
thus remove the redundant setting in this driver.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It appears that preliminary documentation has a typo in the ID list,
i.e. LPSS UART #2 had been advertised wrongly.
Fix the driver according to the EDS v0.9.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Based on the file name and code of the driver, it is likely that this
module is related to TQMx86 and not TQx86.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix sparse warning:
drivers/mfd/stpmic1.c:62:28: warning:
symbol 'stpmic1_regmap_config' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mp2629 is a highly-integrated switching-mode battery charge management
device for single-cell Li-ion or Li-polymer battery.
Add MFD core enables chip access for ADC driver for battery readings,
and a power supply battery-charger driver
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
has_irq member of struct dwapb_port_property is used only in one place,
so, make it local test instead and remove from the structure.
This local test is using memchr_inv() which is quite efficient in comparison
to the original loop and possible little overhead can be neglected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the MediaTek MT6358 PMIC. This is a
multifunction device with the following sub modules:
- Regulator
- RTC
- Codec
- Interrupt
It is interfaced to the host controller using SPI interface
by a proprietary hardware called PMIC wrapper or pwrap.
MT6358 MFD is a child device of the pwrap.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add new struct members for mfd-cells and irq initial function, so we can
call devm_mfd_add_devices() only once.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some pmics don't need backup interrupt settings, so we change to use
pm notifier for the pmics which are necessary to store settings.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Gateworks System Controller (GSC) is an I2C slave controller
implemented with an MSP430 micro-controller whose firmware embeds the
following features:
- I/O expander (16 GPIO's) using PCA955x protocol
- Real Time Clock using DS1672 protocol
- User EEPROM using AT24 protocol
- HWMON using custom protocol
- Interrupt controller with tamper detect, user pushbotton
- Watchdog controller capable of full board power-cycle
- Power Control capable of full board power-cycle
see http://trac.gateworks.com/wiki/gsc for more details
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
i801_add_mux() fills in the GPIO lookup table by manually populating an
array of gpiod_lookup structures. Use the existing GPIO_LOOKUP_IDX()
helper macro instead, to relax a dependency on the gpiod_lookup
structure's member names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200511145257.22970-3-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There's only a single caller of vexpress_config_set_master() from
vexpress-sysreg.c. Let's just make the registers needed available to
vexpress-config and move all the code there. The registers needed aren't
used anywhere else either. With this, we can get rid of the private API
between these 2 drivers.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Enable building the vexpress-sysreg driver as a module.
As deferred probe between the vexpress components works now, we don't
need to create struct devices early with of_platform_device_create().
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Use the managed devm_gpiochip_add_data() and devm_mfd_add_devices()
instead of their unmanaged counterparts. With this, no .remove() hook is
needed for driver unbind.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The "sys_id", "sys_misc" and "sys_procid" devices don't have a user
anywhere in the tree and do nothing more than create a syscon regmap for
a single register or 2. That's an overkill for creating child devices.
Let's just remove them.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Nothing in the VExpress sysregs nor the MFD child drivers use
CONFIG_CLKSRC_MMIO. There's the 24MHz counter, but that's handled by
drivers/clocksource/timer-versatile.c which doesn't use
CONFIG_CLKSRC_MMIO either. So let's just drop CONFIG_CLKSRC_MMIO.
As the !ARCH_USES_GETTIMEOFFSET dependency was added for
CONFIG_CLKSRC_MMIO, that can be dropped, too.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
vexpress_flags_set() is only used by the platform SMP related code and
has nothing to do with the vexpress-sysreg MFD driver other than both
access the same h/w block. It's also only needed for 32-bit systems and
must be built-in for them. Let's move vexpress_flags_set() closer to
where it is being used. This will allow for vexpress-sysreg to be built
as a module.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This driver only creates a bunch of platform devices sharing resources
belonging to the PMC device. This is pretty much what MFD subsystem is
for so move the driver there, renaming it to intel_pmc_bxt.c which
should be more clear what it is.
MFD subsystem provides nice helper APIs for subdevice creation so
convert the driver to use those. Unfortunately the ACPI device includes
separate resources for most of the subdevices so we cannot simply call
mfd_add_devices() to create all of them but instead we need to call it
separately for each device.
The new MFD driver continues to expose two sysfs attributes that allow
userspace to send IPC commands to the PMC/SCU to avoid breaking any
existing applications that may use these. Generally this is bad idea so
document this in the ABI documentation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This converts the Intel Merrifield PMIC driver over the new SCU IPC API
where the SCU IPC instance is passed to the functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the Intel Broxton Whiskey Cover PMIC driver to use the new SCU
IPC API. This allows us to get rid of the PMC IPC implementation which
is now covered in SCU IPC driver. We drop the error log if the IPC
command fails because intel_scu_ipc_dev_command() does that already.
Also move PMIC specific IPC message constants to the PMIC driver from
the intel_pmc_ipc.h header.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The SCU IPC functionality is usable outside of Intel MID devices. For
example modern Intel CPUs include the same thing but now it is called
PMC (Power Management Controller) instead of SCU. To make the IPC
available for those split the driver into core part (intel_scu_ipc.c)
and the SCU PCI driver part (intel_scu_pcidrv.c) which then calls the
former before it goes and creates rest of the SCU devices. The SCU IPC
will also register a new class that gets assigned to the device that is
created under the parent PCI device.
We also split the Kconfig symbols so that INTEL_SCU_IPC enables the SCU
IPC library and INTEL_SCU_PCI the SCU driver and convert the users
accordingly. While there remove default y from the INTEL_SCU_PCI symbol
as it is already selected by X86_INTEL_MID.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Elkhart Lake LPSS I2C has 100 MHz input clock instead of 133 MHz
that was our preliminary information. This will result slower I2C bus
clock when driver calculates its timing parameters in case ACPI tables
don't provide them.
Slower I2C bus clock is allowed but let's fix this to match with
reality.
While at it, keep the same default I2C device properties as Intel
Broxton since it is not known do they need any update.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is still one call of sprintf() without checking the proper
buffer overflow in aat2870_dump_reg(). Replace it with scnprintf()
call for covering that.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On some platforms user may want to enumerate DLN2 device, its children,
to be enumerated via ACPI. In order to achieve this, let's distinguish
children by _ADR value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The da9062 interrupt handler cannot necessarily be low active.
Add a function to configure the interrupt type based on what is defined in the device tree.
The allowable interrupt type is either low or high level trigger.
Signed-off-by: Shreyas Joshi <shreyas.joshi@biamp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
While the commit 2b8bd606b1 ("mfd: dln2: More sanity checking for endpoints")
tries to harden the sanity checks it made at the same time a regression,
i.e. mixed in and out endpoints. Obviously it should have been not tested on
real hardware at that time, but unluckily it didn't happen.
So, fix above mentioned typo and make device being enumerated again.
While here, introduce an enumerator for magic values to prevent similar issue
to happen in the future.
Fixes: 2b8bd606b1 ("mfd: dln2: More sanity checking for endpoints")
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Comet Lake PCH-V has the same LPSS than Intel Kaby Lake.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Spreadtrum SC27XX series PMICs supply the USB charger type detection
function, and related registers are located on the PMIC global registers
region, thus we implement and export this function in the MFD driver for
users to get the USB charger type.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
RK805 has the same kind of dual-role sleep/shutdown pin as RK809/RK817,
so it makes little sense for the driver to have to have two completely
different mechanisms to handle essentially the same thing. Move RK805
over to the shutdown/suspend flow to clean things up.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rather than having 3 almost-identical functions plus the machinery to
keep track of them, it's far simpler to just dynamically select the
appropriate register field per variant.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Setting the SLEEP pin to its shutdown function for appropriate PMICs
doesn't need to happen in single-CPU context, so there's really no point
involving the syscore machinery. Hook it up to the standard driver model
shutdown method instead. This also obviates the issue that the syscore
ops weren't being unregistered on probe failure or module removal.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK809/RK817 suspend/resume hooks should not have to depend on
whether this driver owns the pm_power_off hook, and thus the global
rk808_i2c_client is set - indeed, the GPIO-based control is really
only relevant when PSCI firmware is in charge of power rather than
the kernel. As driver model callbacks, they have an appropriate
device argument to hand, so can just always use that.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With the device tree property "rockchip,system-power-controller" we
explicitly request to use this PMIC to power off the system. So always
register our poweroff function, even if some other handler (probably
PSCI poweroff) was registered before.
This does tend to reveal a warning on shutdown due to the Rockchip I2C
driver not implementing an atomic transfer method, however since the
write to DEV_OFF takes effect immediately the I2C completion interrupt
is moot anyway, and as the very last thing written to the console it is
only visible to users going out of their way to capture serial output.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
[ rm: note potential warning in commit message ]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
device_driver name is const char pointer, so it not useful to cast
xx_driver_name (which is already const char).
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix several variations of typo around functionali{ty,es}.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If only cpcap mfd driver is selected we will get:
ERROR: "devm_mfd_add_devices" [drivers/mfd/motorola-cpcap.ko] undefined!
This is because Kconfig is missing select for MFD_CORE.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a check to ensure there is indeed an EC device tree entry before
adding the cros-usbpd-notify device. This covers configs where both
CONFIG_ACPI and CONFIG_OF are defined, but the EC device is defined
using device tree and not in ACPI.
Fixes: 4602dce036 ("mfd: cros_ec: Add cros-usbpd-notify subdevice")
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
That list was just empty, so it can be removed if .probe_new
instead of .probe is used
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the RC5T619 has a RTC, use a separate subdevice list for that.
The ADC should be the same as in the RN5T618, according to drivers
in the wild, but since it is not tested, the ADC is only added for
the RC5T619.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Defines for some RTC related registers were missing, also
they were not included in the volatile register list
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds support for IRQ handling in the RC5T619 which is required
for properly implementing subdevices like RTC.
For now only definitions for the variant RC5T619 are included.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds core support for the Azoteq IQS620A, IQS621, IQS622,
IQS624 and IQS625 multi-function sensors.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
* CrOS EC
- Refactoring of some of cros_ec's headers. include/linux/mfd/cros_ec.h now
removed, new cros_ec.h added drivers/platform/chrome which contains shared
operations of cros_ec transport drivers.
- Response tracing in cros_ec_proto
* Wilco EC
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
* Misc
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXjij4AAKCRBzbaomhzOw
wrFjAP0bU5PFkxprCOTY9kF/cMgHPDljEPES4FVV11eGyYr3HgD/StpuIhFGrh7+
Fz96dDdNu1melyGjmMqSN/M9JFo+Hw4=
=FB/I
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Refactoring of some of cros_ec's headers:
include/linux/mfd/cros_ec.h now removed, new cros_ec.h added to
drivers/platform/chrome which contains shared operations of cros_ec
transport drivers.
- Response tracing in cros_ec_proto
Wilco EC:
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard
backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
Misc:
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device"
* tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec: Match implementation with headers
platform/chrome: cros_ec: Drop unaligned.h include
platform/chrome: wilco_ec: Allow wilco to be compiled in COMPILE_TEST
platform/chrome: wilco_ec: Add newlines to printks
platform/chrome: wilco_ec: Fix unregistration order
cros_ec: treewide: Remove 'include/linux/mfd/cros_ec.h'
platform/chrome: cros_ec_ishtp: Make init_lock static
platform/chrome: chromeos_laptop: Convert to i2c_new_scanned_device
platform/chrome: cros_ec_lpc: Use platform_get_irq_optional() for optional IRQs
platform/chrome: cros_ec_proto: Add response tracing
platform/chrome: cros_ec_trace: Match trace commands with EC commands
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
- New Device Support
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
- New Functionality
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
- Fix-ups
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers; madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
- Bug Fixes
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon
-----BEGIN PGP SIGNATURE-----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=t4+B
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
- Support mremap() for the VDSO, primarily to allow CRIU to restore the
VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement of
the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs by
running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to
take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXjRnpxYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDdNYoA/3ZhgKX1L/hwvkPKwu7FxbL41pjB
WAm8IYDaxPvgxkcSAP9FNNepHK+oBPM8I2e3DvDvmcuYjumztdikzYbJ5HuMBA==
=MV2S
-----END PGP SIGNATURE-----
Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS changes from Paul Burton:
"Nothing too big or scary in here:
- Support mremap() for the VDSO, primarily to allow CRIU to restore
the VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement
of the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs
by running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style
MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them
to take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups"
* tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits)
MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel
MIPS: Loongson64: Disable exec hazard
MIPS: Loongson64: Bump ISA level to MIPSR2
MIPS: Make DIEI support as a config option
MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too"
MIPS: asm: local: add barriers for Loongson
MIPS: Loongson64: Select mac2008 only feature
MIPS: Add MAC2008 Support
Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel"
MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again)
MIPS: make CPU_HAS_LOAD_STORE_LR opt-out
MIPS: generic: don't unconditionally select PINCTRL
MIPS: don't explicitly select LIBFDT in Kconfig
MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts
MIPS: SGI-IP30: Check for valid pointer before using it
MIPS: syscalls: fix indentation of the 'SYSNR' message
MIPS: boot: fix typo in 'vmlinux.lzma.its' target
MIPS: fix indentation of the 'RELOCS' message
dt-bindings: Document loongson vendor-prefix
MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi.
...
Qualcomm WCD9340/WCD9341 Codec is a standalone Hi-Fi audio codec IC.
This codec has integrated SoundWire controller, pin controller and
interrupt controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are a lot of similar global registers being used across multiple SoCs
from Unisoc. But most of these registers are assigned with different offset
for different SoCs. It is hard to handle all of them in an all-in-one
kernel image.
Add a helper function to get regmap with arguments where we could put some
extra information such as the offset value.
Signed-off-by: Orson Zhai <orson.zhai@unisoc.com>
Tested-by: Baolin Wang <baolin.wang@unisoc.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a bit which gets cleared after conversion.
Fixes: 9bb9e29c78 ("mfd: Add Ricoh RN5T618 PMIC core driver")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the cros-usbpd-notify driver as a subdevice on platforms that
support the EC_FEATURE_USB_PD EC feature flag and don't have the
ACPI PD notification device defined.
This driver allows other cros-ec devices to receive PD event
notifications from the Chrome OS Embedded Controller (EC) via a
notification chain.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The watchdog driver compatible is "dlg,da9062-watchdog" and not
"dlg,da9062-wdt". Therefore the mfd-core can't populate the of_node and
fwnode. As result the watchdog driver can't parse the devicetree.
Fixes: 9b40b030c4 ("mfd: da9062: Supply core driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Both manual and power on resets have a brief period where the chip will
not be accessible immediately afterwards. Extend the time allowed for
this from a minimum of 1mS to 2mS based on newer evaluation of the
hardware and ensure this reset happens in all reset conditions. Whilst
making the change also remove the redundant NULL checks in the reset
functions as the GPIO functions already check for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Accessory detect mode 1 is missing a default, add one to the table.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is advised to wait for the boot done bit to be set before reading
any other register, update the driver to respect this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
name.
"SAMSUNG" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mfd/tqmx86.c: In function ‘tqmx86_probe’:
drivers/mfd/tqmx86.c:161:29: warning: variable ‘i2c_ien’
set but not used I[-Wunused-but-set-variable]
It is never used, and so can be removed.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DSI PLLs are handled by the generic clock framework
since ages, this code is completely unused and misleading.
Delete it.
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The display clocks are handled by the generic clock framework
since ages, this code is completely unused and misleading.
Delete it.
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MAX77650 MFD driver uses regmap_irq API but doesn't select the required
REGMAP_IRQ option in Kconfig. This can cause the following build error
if regmap irq is not enabled implicitly by someone else:
ld: drivers/mfd/max77650.o: in function `max77650_i2c_probe':
max77650.c:(.text+0xcb): undefined reference to `devm_regmap_add_irq_chip'
ld: max77650.c:(.text+0xdb): undefined reference to `regmap_irq_get_domain'
make: *** [Makefile:1079: vmlinux] Error 1
Fix it by adding the missing option.
Fixes: d0f6033450 ("mfd: Add new driver for MAX77650 PMIC")
Reported-by: Paul Gazzillo <paul@pgazz.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On AXP288 and newer PMICs, bit 7 of AXP20X_VBUS_IPSOUT_MGMT can be set
to prevent using the VBUS input. However, when the VBUS unplugged and
plugged back in, the bit automatically resets to zero.
We need to set the register as volatile to prevent regmap from caching
that bit. Otherwise, regcache will think the bit is already set and not
write the register.
Fixes: cd53216625 ("mfd: axp20x: Fix axp288 volatile ranges")
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit f4d41ad844 ("mfd: ab8500: Example using new OF_MFD_CELL MACRO")
has a typo error renaming "ab8500-clk" to "abx500-clk"
with the result att ALSA SoC audio broke as the clock
driver was not probing anymore. Fixed it up.
Fixes: f4d41ad844 ("mfd: ab8500: Example using new OF_MFD_CELL MACRO")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Jasper Lake has the same LPSS than Intel Ice Lake.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
AB8505 support was never fully converted to the device tree.
Most of the MFD cells for AB8505 lack an "of_compatible",
which prevents them from being configured through the device tree.
Align the definition of the AB8505 MFD cells with the ones for AB8500,
and add device tree compatibles. Except for GPIO and regulators the
compatibles are equal to those used for AB8500 because the hardware
does not differ much.
Finally, change db8500_prcmu_register_ab8500() to check for the AB8505
device tree node additionally, and probe it if it is found.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the da9062 GPIO's aren't available. The patch adds the support
to make these available by adding a gpio device with the corresponding
irq resources. Furthermore the patch fixes a minor style issue for the
onkey device.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is not enough to check for the number of endpoints.
The types must also be correct.
Reported-and-tested-by: syzbot+48a2851be24583b864dc@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver misuses release_resource + kfree to match request_mem_region,
which is incorrect.
The right way is to use release_mem_region.
Replace the mismatched calls with the right ones to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of open coded variant use resource_size() and replace
weird '- 3' to more understandable '- 4'.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use gpio_keys to send power input-event to user-space when power
button (short) press is detected.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
BD71828GW is a single-chip power management IC for battery-powered portable
devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA
single-cell linear charger. Also included is a Coulomb counter, a real-time
clock (RTC), 3 GPO/regulator control pins, HALL input and a 32.768 kHz
clock gate.
Add MFD core driver providing interrupt controller facilities and i2c
access to sub device drivers.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ROHM BD71850 PMIC is almost identical to BD71847. Main difference is some
initial voltage values for regulators. The BD71850 can be handled by
BD71847 driver but adding own compatible makes it clearer for one who
creates the DT for board containing this PMIC and allows SW to be
differentiating PMICs if needed.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Thanks to Stephen Boyd I today learned we can use platform_device_id
to do device and module matching for MFD sub-devices!
Do device matching using the platform_device_id instead of using
explicit module_aliases to load modules and custom parent-data field
to do module loading and sub-device matching.
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
SGI IOC3 chip has integrated ethernet, keyboard and mouse interface.
It also supports connecting a SuperIO chip for serial and parallel
interfaces. IOC3 is used inside various SGI systemboards and add-on
cards with different equipped external interfaces.
Support for ethernet and serial interfaces were implemented inside
the network driver. This patchset moves out the not network related
parts to a new MFD driver, which takes care of card detection,
setup of platform devices and interrupt distribution for the subdevices.
Serial portion: Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Network part: Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Network part: Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-serial@vger.kernel.org
This header file now only includes the cros_ec_dev struct, however, is the
'include/linux/platform_data/cros_ec_proto.h' who contains the definition of
all the Chrome OS EC related structs. There is no reason to have a
separate include for this struct so move to the place where other
structs are defined. That way, we can remove the include itself, but also
simplify the common pattern
#include <linux/mfd/cros_ec.h>
#include <linux/platform_data/cros_ec_proto.h>
for a single include
#include <linux/platform_data/cros_ec_proto.h>
The changes to remove the cros_ec.h include were generated with the
following shell script:
git grep -l "<linux/mfd/cros_ec.h>" | xargs sed -i '/<linux\/mfd\/cros_ec.h>/d'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
For HLCDC timing engine configurations bit ATMEL_HLCDC_SIP of
ATMEL_HLCDC_SR needs to be polled before applying new config. In case of
timeout there is no indicator about this, so, return in case of timeout
and also print a message about this.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add struct device member to struct atmel_hlcdc_regmap to be
able to use dev_*() specific logging functions.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move the Crystal Cove PMIC panel GPIO lookup-table from
drivers/mfd/intel_soc_pmic_core.c to the i915 driver.
The moved looked-up table is adding a GPIO lookup to the i915 PCI
device and the GPIO subsys allows only one lookup table per device,
The intel_soc_pmic_core.c code only adds lookup-table entries for the
PMIC panel GPIO (as it deals only with the PMIC), but we also need to be
able to access some GPIOs on the SoC itself, which requires entries for
these GPIOs in the lookup-table.
Since the lookup-table is attached to the i915 PCI device it really
should be part of the i915 driver, this will also allow us to extend
it with GPIOs from other sources when necessary.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-5-hdegoede@redhat.com
At least Bay Trail (BYT) and Cherry Trail (CHT) devices can use 1 of 2
different PWM controllers for controlling the LCD's backlight brightness.
Either the one integrated into the PMIC or the one integrated into the
SoC (the 1st LPSS PWM controller).
So far in the LPSS code on BYT we have skipped registering the LPSS PWM
controller "pwm_backlight" lookup entry when a Crystal Cove PMIC is
present, assuming that in this case the PMIC PWM controller will be used.
On CHT we have been relying on only 1 of the 2 PWM controllers being
enabled in the DSDT at the same time; and always registered the lookup.
So far this has been working, but the correct way to determine which PWM
controller needs to be used is by checking a bit in the VBT table and
recently I've learned about 2 different BYT devices:
Point of View MOBII TAB-P800W
Acer Switch 10 SW5-012
Which use a Crystal Cove PMIC, yet the LCD is connected to the SoC/LPSS
PWM controller (and the VBT correctly indicates this), so here our old
heuristics fail.
Since only the i915 driver has access to the VBT, this commit renames
the "pwm_backlight" lookup entries for the Crystal Cove PMIC's PWM
controller to "pwm_pmic_backlight" so that the i915 driver can do a
pwm_get() for the right controller depending on the VBT bit, instead of
the i915 driver relying on a "pwm_backlight" lookup getting registered
which magically points to the right controller.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216202906.1662893-3-hdegoede@redhat.com
* CrOS EC / MFD / IIO
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part of a
series from Gwendal to refactor sensor code between MFD, CrOS EC, iio
and input in order to add a new sensorhub driver and FIFO processing
* Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
* Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXeaqtwAKCRBzbaomhzOw
wilIAQCQ3/dpAwg2skKYYf3RBLDJeDLA1id7rNSgMOXc2aKyTAD/fCQtNhwj+Hal
W//04WWngTCQF5fkE9OCJrDwbm5eRwc=
=uOGe
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform changes from Benson Leung:
"CrOS EC / MFD / IIO:
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part
of a series from Gwendal to refactor sensor code between MFD, CrOS
EC, iio and input in order to add a new sensorhub driver and FIFO
processing
Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue)"
* tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: fix use after free issue
platform/chrome: cros_ec: Add Kconfig default for cros-ec-sensorhub
Revert "Input: cros_ec_keyb: mask out extra flags in event_type"
Revert "Input: cros_ec_keyb - add back missing mask for event_type"
platform/chrome: cros_ec: handle MKBP more events flag
platform/chrome: cros_ec: Do not attempt to register a non-positive IRQ number
platform/chrome: cros-ec: Record event timestamp in the hard irq
mfd / platform / iio: cros_ec: Register sensor through sensorhub
iio / platform: cros_ec: Add cros-ec-sensorhub driver
mfd / platform: cros_ec: Add sensor_count and make check_features public
platform/chrome: cros_ec: Put docs with the code
platform/chrome: cros_usbpd_logger: add missed destroy_workqueue in remove
platform/chrome: cros_ec: Fix Kconfig indentation
platform/chrome: wilco_ec: Add keyboard backlight LED support
platform/chrome: wilco_ec: Add charging config driver
platform/chrome: wilco_ec: Add Dell's USB PowerShare Policy control
platform/chrome: wilco_ec: Add debugfs test_event file
- Add support for a "resource managed strongly uncachable ioremap" call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
- New Drivers
- Add support for MediaTek MT6323 PMIC
- New Device Support
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
- New Functionality
- Add support for requested supply clocks; madera-core
- Fix-ups
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona, syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
- Bug Fixes
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc
-----BEGIN PGP SIGNATURE-----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=mugH
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for a "resource managed strongly uncachable ioremap"
call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
New Drivers:
- Add support for MediaTek MT6323 PMIC
New Device Support:
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC
CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
New Functionality:
- Add support for requested supply clocks; madera-core
Fix-ups:
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona,
syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
Bug Fixes:
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc"
* tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (47 commits)
Revert "mfd: syscon: Set name of regmap_config"
mfd: ti_am335x_tscadc: Fix static checker warning
mfd: bd70528: Staticize bit value definitions
mfd: mfd-core: Honour Device Tree's request to disable a child-device
dt-bindings: mfd: max77693: Fix missing curly brace
mfd: intel-lpss: Add Intel Comet Lake PCH-H PCI IDs
mfd: db8500-prcmu: Support U8420-sysclk firmware
dt-bindings: mfd: max77650: Convert the binding document to yaml
mfd: mfd-core: Move pdev->mfd_cell creation back into mfd_add_device()
mfd: mfd-core: Remove usage counting for .{en,dis}able() call-backs
x86: olpc-xo1-sci: Remove invocation of MFD's .enable()/.disable() call-backs
x86: olpc-xo1-pm: Remove invocation of MFD's .enable()/.disable() call-backs
mfd: mfd-core: Remove mfd_clone_cell()
mfd: mfd-core: Protect against NULL call-back function pointer
mfd: cs5535-mfd: Register clients using their own dedicated MFD cell entries
mfd: cs5535-mfd: Request shared IO regions centrally
mfd: cs5535-mfd: Remove mfd_cell->id hack
mfd: cs5535-mfd: Use PLATFORM_DEVID_* defines and tidy error message
mfd: intel_soc_pmic_crc: Add "cht_crystal_cove_pmic" cell to CHT cells
mfd: madera: Add support for requesting the supply clocks
...
Drivers:
* test_power: add support for current and charge_counter
* cpcap-charger: improve charge calculation and limit default charge voltage
* ab8500: convert to IIO
* misc. small fixes all over drivers
-----BEGIN PGP SIGNATURE-----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=iHhO
-----END PGP SIGNATURE-----
Merge tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- test_power: add support for current and charge_counter
- cpcap-charger: improve charge calculation and limit default charge
voltage
- ab8500: convert to IIO
- misc small fixes all over drivers
* tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (29 commits)
power: supply: bd70528: Add MODULE_ALIAS to allow module auto loading
power: supply: ab8500_charger: Fix inconsistent IS_ERR and PTR_ERR
power: supply: cpcap-charger: cpcap_charger_voltage_to_regval() can be static
power: supply: cpcap-battery: Add basic coulomb counter calibrate support
power: supply: cpcap-battery: Read and save integrator register CCI
power: supply: cpcap-battery: Simplify short term power average calculation
power: supply: cpcap-battery: Simplify coulomb counter calculation with div_s64
power: supply: cpcap-battery: Move coulomb counter units per lsb to ddata
power: supply: cpcap-charger: Allow changing constant charge voltage
power: supply: cpcap-battery: Fix handling of lowered charger voltage
power: supply: cpcap-charger: Improve battery detection
power: supply: cpcap-battery: Check voltage before orderly_poweroff
power: supply: cpcap-charger: Limit voltage to 4.2V for battery
power: supply: ab8500: Handle invalid IRQ from platform_get_irq_byname()
power: supply: ab8500_fg: Do not free non-requested IRQs in probe's error path
power: supply: ab8500: Cleanup probe in reverse order
power: reset: at91: fix __le32 cast in reset code
power: supply: abx500_chargalg: Fix code indentation
mfd: Switch the AB8500 GPADC to IIO
iio: adc: New driver for the AB8500 GPADC
...
- Update the ACPICA code in the kernel to upstream revision 20191018
including:
* Fixes for Clang warnings (Bob Moore).
* Fix for possible overflow in get_tick_count() (Bob Moore).
* Introduction of acpi_unload_table() (Bob Moore).
* Debugger and utilities updates (Erik Schmauss).
* Fix for unloading tables loaded via configfs (Nikolaus Voss).
- Add support for EFI specific purpose memory to optionally allow
either application-exclusive or core-kernel-mm managed access to
differentiated memory (Dan Williams).
- Fix and clean up processing of the HMAT table (Brice Goglin,
Qian Cai, Tao Xu).
- Update the ACPI EC driver to make it work on systems with
hardware-reduced ACPI (Daniel Drake).
- Always build in support for the Generic Event Device (GED) to
allow one kernel binary to work both on systems with full
hardware ACPI and hardware-reduced ACPI (Arjan van de Ven).
- Fix the table unload mechanism to unregister platform devices
created when the given table was loaded (Andy Shevchenko).
- Rework the lid blacklist handling in the button driver and add
more lid quirks to it (Hans de Goede).
- Improve ACPI-based device enumeration for some platforms based
on Intel BayTrail SoCs (Hans de Goede).
- Add an OpRegion driver for the Cherry Trail Crystal Cove PMIC
and prevent handlers from being registered for unhandled PMIC
OpRegions (Hans de Goede).
- Unify ACPI _HID/_UID matching (Andy Shevchenko).
- Clean up documentation and comments (Cao jin, James Pack, Kacper
Piwiński).
-----BEGIN PGP SIGNATURE-----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=7Cqr
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20191018, add support for EFI specific purpose memory, update the ACPI
EC driver to make it work on systems with hardware-reduced ACPI,
improve ACPI-based device enumeration for some platforms, rework the
lid blacklist handling in the button driver and add more lid quirks to
it, unify ACPI _HID/_UID matching, fix assorted issues and clean up
the code and documentation.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20191018
including:
* Fixes for Clang warnings (Bob Moore)
* Fix for possible overflow in get_tick_count() (Bob Moore)
* Introduction of acpi_unload_table() (Bob Moore)
* Debugger and utilities updates (Erik Schmauss)
* Fix for unloading tables loaded via configfs (Nikolaus Voss)
- Add support for EFI specific purpose memory to optionally allow
either application-exclusive or core-kernel-mm managed access to
differentiated memory (Dan Williams)
- Fix and clean up processing of the HMAT table (Brice Goglin, Qian
Cai, Tao Xu)
- Update the ACPI EC driver to make it work on systems with
hardware-reduced ACPI (Daniel Drake)
- Always build in support for the Generic Event Device (GED) to allow
one kernel binary to work both on systems with full hardware ACPI
and hardware-reduced ACPI (Arjan van de Ven)
- Fix the table unload mechanism to unregister platform devices
created when the given table was loaded (Andy Shevchenko)
- Rework the lid blacklist handling in the button driver and add more
lid quirks to it (Hans de Goede)
- Improve ACPI-based device enumeration for some platforms based on
Intel BayTrail SoCs (Hans de Goede)
- Add an OpRegion driver for the Cherry Trail Crystal Cove PMIC and
prevent handlers from being registered for unhandled PMIC OpRegions
(Hans de Goede)
- Unify ACPI _HID/_UID matching (Andy Shevchenko)
- Clean up documentation and comments (Cao jin, James Pack, Kacper
Piwiński)"
* tag 'acpi-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
ACPI: OSI: Shoot duplicate word
ACPI: HMAT: use %u instead of %d to print u32 values
ACPI: NUMA: HMAT: fix a section mismatch
ACPI: HMAT: don't mix pxm and nid when setting memory target processor_pxm
ACPI: NUMA: HMAT: Register "soft reserved" memory as an "hmem" device
ACPI: NUMA: HMAT: Register HMAT at device_initcall level
device-dax: Add a driver for "hmem" devices
dax: Fix alloc_dax_region() compile warning
lib: Uplevel the pmem "region" ida to a global allocator
x86/efi: Add efi_fake_mem support for EFI_MEMORY_SP
arm/efi: EFI soft reservation to memblock
x86/efi: EFI soft reservation to E820 enumeration
efi: Common enable/disable infrastructure for EFI soft reservation
x86/efi: Push EFI_MEMMAP check into leaf routines
efi: Enumerate EFI_MEMORY_SP
ACPI: NUMA: Establish a new drivers/acpi/numa/ directory
ACPICA: Update version to 20191018
ACPICA: debugger: remove leading whitespaces when converting a string to a buffer
ACPICA: acpiexec: initialize all simple types and field units from user input
ACPICA: debugger: add field unit support for acpi_db_get_next_token
...
Remove the duplicated code in MFD, since MFD just registers cros-ec-sensorhub
if at least one sensor is present.
Change IIO cros-ec driver to get the pointer to the cros-ec-dev through
cros-ec-sensorhub.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add a new function to return the number of MEMS sensors available in a
ChromeOS Embedded Controller. It uses MOTIONSENSE_CMD_DUMP if available
or a specific memory map ACPI registers to find out.
Also, make check_features public as it can be useful for other drivers
to know what the Embedded Controller supports.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
This driver currently requires platform data to specify the
operational mode and regulator init data (in case of regulator
mode).
Optionally specify the operational mode by looking at the name
of the devicetree child node.
Example: put chip in regulator mode:
i2c0 {
tps61052@33 {
compatible = "ti,tps61052";
reg = <0x33>;
regulator {
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
};
};
};
Tree: linux-next
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191119154611.29625-2-TheSven73@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 500f9ff518.
The original commit is a duplication of the exactly previously added
commit 408d1d570a ("mfd: syscon: Set regmap name to DT node name").
Revert the unnecessary later one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is possible that platform_get_resource() might return NULL and
therefore code needs to check for this condition before
de-referencing the pointer.
Therefore move the de-referencing of 'res' pointer after
devm_ioremap_resource() which would have checked the validity of the
pointer.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make bit definitions static to reduce the scope.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Until now, MFD has assumed all child devices passed to it (via
mfd_cells) are to be registered. It does not take into account
requests from Device Tree and the like to disable child devices
on a per-platform basis.
Well now it does.
Link: https://www.spinics.net/lists/arm-kernel/msg366309.html
Link: https://lkml.org/lkml/2019/8/22/1350
Reported-by: Barry Song <Baohua.Song@csr.com>
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Comet Lake PCH-H has the same LPSS than Intel Cannon Lake.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a distinct version of the Ux500 U8420 variant
with "sysclk", as can be seen from the vendor code that
didn't make it upstream, this firmware lacks the
ULPPLL (ultra-low power phase locked loop) which in
effect means that the timer clock is instead wired to
the 32768 Hz always-on clock.
This has some repercussions when enabling the timer
clock as the code as it stands will disable the timer
clock on these platforms (lacking the so-called
"doze mode") and obtaining the wrong rate of the timer
clock.
The timer frequency is of course needed very early in
the boot, and as a consequence, we need to shuffle
around the early PRCMU init code: whereas in the past
we did not need to look up the PRCMU firmware version
in the early init, but now we need to know the version
before the core system timers are registered so we
restructure the platform callbacks to the PRCMU so as
not to take any arguments and instead look up the
resources it needs directly from the device tree
when initializing.
As we do not yet support any platforms using this
firmware it is not a regression, but as PostmarketOS
is starting to support products with this firmware we
need to fix this up.
The low rate of 32kHz also makes the MTU timer unsuitable
as delay timer but this needs to be fixed in a separate
patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Most of the complexity of mfd_platform_add_cell() has been removed. The
only functionality left duplicates cell memory into the child's platform
device. Since it's only a few lines, moving it to the main thread and
removing the superfluous function makes sense.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
The MFD implementation for reference counting was complex and unnecessary.
There was only one bona fide user which has now been converted to handle
the process in a different way. Any future resource protection, shared
enablement functions should be handed by the parent device, rather than
through the MFD subsystem API.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Providing a subsystem-level API helper seems over-kill just to save a
few lines of C-code. Previous commits saw us convert mfd_clone_cell()'s
only user over to use a more traditional style of MFD child-device
registration. Now we can remove the superfluous helper from the MFD API.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
If a child device calls mfd_cell_{en,dis}able() without an appropriate
call-back being set, we are likely to encounter a panic. Avoid this
by adding suitable checking.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
CS5535 is the only user of mfd_clone_cell(). It makes more sense to
register child devices in the traditional way and remove the quite
bespoke mfd_clone_cell() call from the MFD API.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Prior to this patch, IO regions were requested via an MFD subsytem-level
.enable() call-back and similarly released by a .disable() call-back.
Double requests/releases were avoided by a centrally handled usage count
mechanism.
This complexity can all be avoided by handling IO regions only once during
.probe() and .remove() of the parent device. Since this is the only
legitimate user of the aforementioned usage count mechanism, this patch
will allow it to be removed from MFD core in subsequent steps.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
The current implementation abuses the platform 'id' mfd_cell member
to index into the correct resources entry. Seeing as enough resource
slots are already available, let's just loop through all available
bars and allocate them to their appropriate slot, even if they happen
to be zero.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
In most contexts '-1' doesn't really mean much to the casual observer.
In almost all cases, it's better to use a human readable define. In
this case PLATFORM_DEVID_* defines have already been provided for this
purpose.
While we're here, let's be specific about the 'MFD devices' which
failed. It will help when trying to distinguish which of the 2 sets
of sub-devices we actually failed to register.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Add a "cht_crystal_cove_pmic" cell to the cells for the Cherry Trail
variant of the Crystal Cove PMIC. Adding this cell enables / hooks-up
the new Cherry Trail Crystal Cove PMIC OpRegion driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the ability to get the clock for each clock input pin of the chip
and enable MCLK2 since that is expected to be a permanently enabled
32kHz clock.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Save a few bytes by removing some registers from the driver that are not
currently used and not intended to be used at any point in the future.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the correct macro when adding the MFD devices instead of using
directly '-1' value.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Part 3 from this series [1] was not merged due to wrong splitting
and breaks mt6323 pmic on bananapi-r2
dmesg prints this line and at least switch is not initialized on bananapi-r2
mt6397 1000d000.pwrap:mt6323: unsupported chip: 0x0
this patch contains only the probe-changes and chip_data structs
from original part 3 by Hsin-Hsiung Wang
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=164155
Fixes: a4872e80ce ("mfd: mt6397: Extract IRQ related code from core driver")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that gpiolib recognizes wlf,reset legacy GPIO and will handle it
even if DTS uses it without -gpio[s] suffix, we can switch to more
standard devm_gpiod_get() and later remove devm_gpiod_get_from_of_node().
Note that we will lose "arizona /RESET" custom GPIO label, but since we
do not set such custom label when using the modern binding, I opted to
not having it here either.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
regmap_add_irq_chip() will try to allocate all of the IRQ descriptors
upfront if passed a non-zero irq_base parameter. However, the intention
is to allocate IRQ descriptors on an as-needed basis if possible. Pass 0
instead of -1 to fix that use-case.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the subtype and compatible strings for PM8950 and PMI8950,
found in various SoCs, including MSM8953, MSM8956, MSM8976 and
APQ variants.
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Do not open code the definition, instead use the nice DEFINE_RES_IRQ
macro for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All other rk8xx operate with the polarity on low and even the old
submitted devicetree snippet for the px30-evb declared the irq as low.
So bring the rk817 preset in line with this, as there is really no
reason for it to be the only with with a high polarity.
The rk809/rk817 hasn't been added to any devicetrees so far, so this
won't break anything.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The pwrkey integration seems to stem from the vendor kernel, as the
compatible is wrong and also the order of key-irqs is swapped.
So fix these issues to make the pwrkey on rk817 actually work.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It turned out Intel Gemini Lake doesn't use the same I2C timing
parameters as Broxton.
I got confirmation from the Windows team that Gemini Lake systems should
use updated timing parameters that differ from those used in Broxton
based systems.
Fixes: f80e78aa11 ("mfd: intel-lpss: Add Intel Gemini Lake PCI IDs")
Tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some BIOS erroneously specifies write-combining BAR for intel-lpss-pci
in MTRR. This will cause the system to hang during boot. If possible,
this bug could be corrected with a firmware update.
This patch use devm_ioremap_uc to overwrite/ignore the MTRR settings
by forcing the use of strongly uncachable pages for intel-lpss.
The BIOS bug is present on Dell XPS 13 7390 2-in-1:
[ 0.001734] 5 base 4000000000 mask 6000000000 write-combining
4000000000-7fffffffff : PCI Bus 0000:00
4000000000-400fffffff : 0000:00:02.0 (i915)
4010000000-4010000fff : 0000:00:15.0 (intel-lpss-pci)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203485
Cc: <stable@vger.kernel.org> # v4.19+
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Tuowen Zhao <ztuowen@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Roman Gilg <subdiff@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Our current Crystal Cove OpRegion driver is only valid for the
Crystal Cove PMIC variant found on Bay Trail (BYT) boards,
Cherry Trail (CHT) based boards use another variant.
At least the regulator registers are different on CHT and these registers
are one of the things controlled by the custom PMIC OpRegion.
Commit 4d9ed62ab1 ("mfd: intel_soc_pmic: Export separate mfd-cell
configs for BYT and CHT") has disabled the intel_pmic_crc.c code for CHT
devices by removing the "crystal_cove_pmic" MFD cell on CHT devices.
This commit renames the intel_pmic_crc.c driver and the cell to be
prefixed with "byt" to indicate that this code is for BYT devices only.
This is a preparation patch for adding a separate PMIC OpRegion
driver for the CHT variant of the Crystal Cove PMIC (sometimes called
Crystal Cove Plus in Android kernel sources).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Part 3 from this series [1] was not merged due to wrong splitting
and breaks mt6323 pmic on bananapi-r2
dmesg prints this line and at least switch is not initialized on bananapi-r2
mt6397 1000d000.pwrap:mt6323: unsupported chip: 0x0
this patch contains only the probe-changes and chip_data structs
from original part 3 by Hsin-Hsiung Wang
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=164155
Fixes: a4872e80ce ("mfd: mt6397: Extract IRQ related code from core driver")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AB8500 GPADC driver is indeed a "general purpose ADC" driver,
and while the IIO subsystem did not exist when the driver was
first merged, it is never too late to clean things up and move it
to the right place.
Nowadays IIO provides the right abstractions and interfaces to
do generic ADC work in the kernel.
We have to cut a bunch of debugfs luggage to make this transition
swift, but all these files to is read out the raw values of the
ADC and the IIO subsystem already has a standard sysfs ABI for
doing exactly this: no debugfs is needed.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull thermal SoC updates from Eduardo Valentin:
"This is a really small pull in the midst of a lot of pending patches.
We are in the middle of restructuring how we are maintaining the
thermal subsystem, as per discussion in our last LPC. For now, I am
sending just some changes that were pending in my tree. Looking
forward to get a more streamlined process in the next merge window"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: db8500: Rewrite to be a pure OF sensor
thermal: db8500: Use dev helper variable
thermal: db8500: Finalize device tree conversion
thermal: thermal_mmio: remove some dead code
At some point there was an attempt to convert the DB8500
thermal sensor to device tree: a probe path was added
and the device tree was augmented for the Snowball board.
The switchover was never completed: instead the thermal
devices came from from the PRCMU MFD device and the probe
on the Snowball was confused as another set of configuration
appeared from the device tree.
Move over to a device-tree only approach, as we fixed up
the device trees.
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
Here is the big set of USB patches for 5.4-rc1.
Two major chunks of code are moving out of the tree and into the staging
directory, uwb and wusb (wireless USB support), because there are no
devices that actually use this protocol anymore, and what we have today
probably doesn't work at all given that the maintainers left many many
years ago. So move it to staging where it will be removed in a few
releases if no one screams.
Other than that, lots of little things. The usual gadget and xhci and
usb serial driver updates, along with a bunch of sysfs file cleanups due
to the driver core changes to support that. Nothing really major, just
constant forward progress.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIYYQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymn8ACfTi8Y2ku/yqw8Nvs4vQjc08MUDhgAoNnbhsI6
H3HUrZTjJJzuxHCM22Lh
=8ZRm
-----END PGP SIGNATURE-----
Merge tag 'usb-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.4-rc1.
Two major chunks of code are moving out of the tree and into the
staging directory, uwb and wusb (wireless USB support), because there
are no devices that actually use this protocol anymore, and what we
have today probably doesn't work at all given that the maintainers
left many many years ago. So move it to staging where it will be
removed in a few releases if no one screams.
Other than that, lots of little things. The usual gadget and xhci and
usb serial driver updates, along with a bunch of sysfs file cleanups
due to the driver core changes to support that. Nothing really major,
just constant forward progress.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: usbcore: Fix slab-out-of-bounds bug during device reset
usb: cdns3: Remove redundant dev_err call in cdns3_probe()
USB: rio500: Fix lockdep violation
USB: rio500: simplify locking
usb: mtu3: register a USB Role Switch for dual role mode
usb: common: add USB GPIO based connection detection driver
usb: common: create Kconfig file
usb: roles: get usb-role-switch from parent
usb: roles: Add fwnode_usb_role_switch_get() function
device connection: Add fwnode_connection_find_match()
usb: roles: Introduce stubs for the exiting functions in role.h
dt-bindings: usb: mtu3: add properties about USB Role Switch
dt-bindings: usb: add binding for USB GPIO based connection detection driver
dt-bindings: connector: add optional properties for Type-B
dt-binding: usb: add usb-role-switch property
usbip: Implement SG support to vhci-hcd and stub driver
usb: roles: intel: Enable static DRD mode for role switch
xhci-ext-caps.c: Add property to disable Intel SW switch
usb: dwc3: remove generic PHY calibrate() calls
usb: core: phy: add support for PHY calibration
...
Here is the big driver core update for 5.4-rc1.
There was a bit of a churn in here, with a number of core and OF
platform patches being added to the tree, and then after much discussion
and review and a day-long in-person meeting, they were decided to be
reverted and a new set of patches is currently being reviewed on the
mailing list.
Other than that churn, there are two "persistent" branches in here that
other trees will be pulling in as well during the merge window. One
branch to add support for drivers to have the driver core automatically
add sysfs attribute files when a driver is bound to a device so that the
driver doesn't have to manually do it (and then clean it up, as it
always gets it wrong).
There's another branch in here for generic lookup helpers for the driver
core that lots of busses are starting to use. That's the majority of
the non-driver-core changes in this patch series.
There's also some on-going debugfs file creation cleanup that has been
slowly happening over the past few releases, with the goal to hopefully
get that done sometime next year.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIVHA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymEVwCfRPxQHQplI6ZR6h0jPscLSaZnaFIAn1a+rjO2
EFuuXJ5Ip72F5Ch9AW3G
=r8lH
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here is the big driver core update for 5.4-rc1.
There was a bit of a churn in here, with a number of core and OF
platform patches being added to the tree, and then after much
discussion and review and a day-long in-person meeting, they were
decided to be reverted and a new set of patches is currently being
reviewed on the mailing list.
Other than that churn, there are two "persistent" branches in here
that other trees will be pulling in as well during the merge window.
One branch to add support for drivers to have the driver core
automatically add sysfs attribute files when a driver is bound to a
device so that the driver doesn't have to manually do it (and then
clean it up, as it always gets it wrong).
There's another branch in here for generic lookup helpers for the
driver core that lots of busses are starting to use. That's the
majority of the non-driver-core changes in this patch series.
There's also some on-going debugfs file creation cleanup that has been
slowly happening over the past few releases, with the goal to
hopefully get that done sometime next year.
All of these have been in linux-next for a while now with no reported
issues"
[ Note that the above-mentioned generic lookup helpers branch was
already brought in by the LED merge (commit 4feaab05dc) that had
shared it.
Also note that that common branch introduced an i2c bug due to a bad
conversion, which got fixed here. - Linus ]
* tag 'driver-core-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (49 commits)
coccinelle: platform_get_irq: Fix parse error
driver-core: add include guard to linux/container.h
sysfs: add BIN_ATTR_WO() macro
driver core: platform: Export platform_get_irq_optional()
hwmon: pwm-fan: Use platform_get_irq_optional()
driver core: platform: Introduce platform_get_irq_optional()
Revert "driver core: Add support for linking devices during device addition"
Revert "driver core: Add edit_links() callback for drivers"
Revert "of/platform: Add functional dependency link from DT bindings"
Revert "driver core: Add sync_state driver/bus callback"
Revert "of/platform: Pause/resume sync state during init and of_platform_populate()"
Revert "of/platform: Create device links for all child-supplier depencencies"
Revert "of/platform: Don't create device links for default busses"
Revert "of/platform: Fix fn definitons for of_link_is_valid() and of_link_property()"
Revert "of/platform: Fix device_links_supplier_sync_state_resume() warning"
Revert "of/platform: Disable generic device linking code for PowerPC"
devcoredump: fix typo in comment
devcoredump: use memory_read_from_buffer
of/platform: Disable generic device linking code for PowerPC
device.h: Fix warnings for mismatched parameter names in comments
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
Now that these drivers use the usb localmem pool there is no need to
select DMA_DECLARE_COHERENT.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190903084615.19161-7-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use mfd_add_hotplug_devices() helper to register the subdevices. The
helper allows us to reduce the boiler plate and also registers the
subdevices in the same way as used in other functions used in this
files.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The CrOS EC is gaining lots of subdevices that are autodetectable by
sending the EC_FEATURE_GET_CMD, it takes fair amount of boiler plate
code to add those devices. So, add a struct that can be used to quickly
add new subdevices without having to duplicate code.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With the increasing use of dedicated CrOS EC MCUs, it takes a fair amount
of boiler plate code to add those devices, add a struct that can be used
to specify a dedicated CrOS EC MCU so we can just add a new item to it to
define a new dedicated MCU.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch makes use of cros_ec_cmd_xfer_status() instead of
cros_ec_cmd_xfer() so we can remove some redundant code. It also uses
kzalloc instead of kmalloc so we can remove more redundant code.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cros-ec-dev is a multifunction device that now doesn't implement any
chardev communication interface. MFD_CROS_EC_CHARDEV doesn't look
a good name to describe that device and can cause confusion. Hence
rename it to CROS_EC_DEV.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With the purpose of remove the things that far extends the bounds of
what a MFD was designed to do, instantiate the new platform misc
cros-ec-chardev driver and get rid of all the unneeded code. After this
patch the misc chardev driver is a sub-device of the MFD, and all the
new file operations should be implemented there.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
That's a driver to talk with the ChromeOS Embedded Controller via a
miscellaneous character device, it creates an entry in /dev for every
instance and implements basic file operations for communicating with the
Embedded Controller with an userspace application. The API is moved to
the uapi folder, which is supposed to contain the user space API of the
kernel.
Note that this will replace current character device interface
implemented in the cros-ec-dev driver in the MFD subsystem. The idea is
to move all the functionality that extends the bounds of what MFD was
designed to platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, the ChromeOS EC core driver has nothing related to an MFD device, so
move that driver from the MFD subsystem to the platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
An MFD is a device that contains several sub-devices (cells). For instance,
the ChromeOS EC fits in this description as usually contains a charger and
can have other devices with different functions like a Real-Time Clock,
an Audio codec, a Real-Time Clock, ...
If you look at the driver, though, we're doing something odd. We have
two MFD cros-ec drivers where one of them (cros-ec-core) instantiates
another MFD driver as sub-driver (cros-ec-dev), and the latest
instantiates the different sub-devices (Real-Time Clock, Audio codec,
etc).
MFD
------------------------------------------
cros-ec-core
|___ mfd-cellA (cros-ec-dev)
| |__ mfd-cell0
| |__ mfd-cell1
| |__ ...
|
|___ mfd-cellB (cros-ec-dev)
|__ mfd-cell0
|__ mfd-cell1
|__ ...
The problem that was trying to solve is to describe some kind of topology for
the case where we have an EC (cros-ec) chained with another EC
(cros-pd). Apart from that this extends the bounds of what MFD was
designed to do we might be interested on have other kinds of topology that
can't be implemented in that way.
Let's prepare the code to move the cros-ec-core part from MFD to
platform/chrome as this is clearly a platform specific thing non-related
to a MFD device.
platform/chrome | MFD
------------------------------------------
|
cros-ec ________|___ cros-ec-dev
| |__ mfd-cell0
| |__ mfd-cell1
| |__ ...
|
cros-pd ________|___ cros-ec-dev
| |__ mfd-cell0
| |__ mfd-cell1
| |__ ...
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add entry for RTC and Power Controller to MT6323.
Signed-off-by: Josef Friedl <josef.friedl@speed.at>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Simplifies and reduces LoC.
Signed-off-by: Josef Friedl <josef.friedl@speed.at>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DB8520 used in a lot of Samsung phones has a slightly higher
maximum ARMSS frequency than the DB8500. In order to not confuse
the OPP framework and cpufreq, make sure the PRCMU driver
returns the correct frequency.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no need to handle optional module request in the driver
when user space tools has that feature for ages.
Replace custom code by MODULE_SOFTDEP() macro to let user space know
that we would like to have the DMA driver loaded first, if any.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver creates a gpio chip so it needs to include the
appropriate header <linux/gpio/driver.h> explicitly rather
than implicitly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some of the laptops, like ASUS U306UA, may expose LPSS devices via ACPI.
Add their IDs to the list.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since we already are using BIT() macro, use GENMASK() as well for sake of
consistency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add an MFD driver for Intel Merrifield Basin Cove PMIC.
Firmware on the platforms which are using Basin Cove PMIC is "smarter"
than on the rest supported by vanilla kernel. It handles first level
of interrupt itself, while others do it on OS level.
The driver is done in the same way as the rest of Intel PMIC MFD drivers
in the kernel to support the initial design. The design allows to use
one driver among few PMICs without knowing implementation details of
the each hardware version or generation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As mutex_lock might sleep. Function pcap_adc_irq is an interrupt handler.
The use of mutex_lock in pcap_adc_irq may cause sleep in IRQ context.
Replace mutex_lock with spin_lock to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Avoids:
../drivers/mfd/rk808.c:771:1: warning: symbol 'rk8xx_pm_ops' \
was not declared. Should it be static?
Fixes: 5752bc4373 ("mfd: rk808: Mark pm functions __maybe_unused")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The newly added suspend/resume functions are only used if CONFIG_PM
is enabled:
drivers/mfd/rk808.c:752:12: error: 'rk8xx_resume' defined but not used [-Werror=unused-function]
drivers/mfd/rk808.c:732:12: error: 'rk8xx_suspend' defined but not used [-Werror=unused-function]
Mark them as __maybe_unused so the compiler can silently drop them
when they are not needed.
Fixes: 586c1b4125 ("mfd: rk808: Add RK817 and RK809 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is a GPIO driver, use the appropriate header
<linux/gpio/driver.h> rather than the legacy <linux/gpio.h>
header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In order to support different types of irq design, we decide to add
separate irq drivers for different design and keep mt6397 mfd core
simple and reusable to all generations of PMICs so far.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mfd/db8500-prcmu.c: In function 'dsiclk_rate':
drivers/mfd/db8500-prcmu.c:1592:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
div *= 2;
~~~~^~~~
drivers/mfd/db8500-prcmu.c:1593:2: note: here
case PRCM_DSI_PLLOUT_SEL_PHI_2:
^~~~
drivers/mfd/db8500-prcmu.c:1594:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
div *= 2;
~~~~^~~~
drivers/mfd/db8500-prcmu.c:1595:2: note: here
case PRCM_DSI_PLLOUT_SEL_PHI:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Tiger Lake has the same LPSS than Intel Broxton.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It has been replaced with the ingenic-iio driver for the ADC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mfd/omap-usb-host.c: In function 'usbhs_runtime_resume':
drivers/mfd/omap-usb-host.c:303:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!IS_ERR(omap->hsic480m_clk[i])) {
^
drivers/mfd/omap-usb-host.c:313:3: note: here
case OMAP_EHCI_PORT_MODE_TLL:
^~~~
drivers/mfd/omap-usb-host.c: In function 'usbhs_runtime_suspend':
drivers/mfd/omap-usb-host.c:345:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!IS_ERR(omap->hsic480m_clk[i]))
^
drivers/mfd/omap-usb-host.c:349:3: note: here
case OMAP_EHCI_PORT_MODE_TLL:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Goodix touchpad may drop its first couple input events when
i2c-designware-platdrv and intel-lpss it connects to took too long to
runtime resume from runtime suspended state.
This issue happens becuase the touchpad has a rather small buffer to
store up to 13 input events, so if the host doesn't read those events in
time (i.e. runtime resume takes too long), events are dropped from the
touchpad's buffer.
The bottleneck is D3cold delay it waits when transitioning from D3cold
to D0, hence remove the delay to make the resume faster. I've tested
some systems with intel-lpss and haven't seen any regression.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202683
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move from i2c_new_dummy() to devm_i2c_new_dummy_device(). So, we now get
an ERRPTR which we use in error handling and we can skip removal of the
created devices.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mfd/omap-usb-host.c: In function 'usbhs_runtime_resume':
drivers/mfd/omap-usb-host.c:303:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!IS_ERR(omap->hsic480m_clk[i])) {
^
drivers/mfd/omap-usb-host.c:313:3: note: here
case OMAP_EHCI_PORT_MODE_TLL:
^~~~
drivers/mfd/omap-usb-host.c: In function 'usbhs_runtime_suspend':
drivers/mfd/omap-usb-host.c:345:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!IS_ERR(omap->hsic480m_clk[i]))
^
drivers/mfd/omap-usb-host.c:349:3: note: here
case OMAP_EHCI_PORT_MODE_TLL:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mfd/db8500-prcmu.c: In function 'dsiclk_rate':
drivers/mfd/db8500-prcmu.c:1592:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
div *= 2;
~~~~^~~~
drivers/mfd/db8500-prcmu.c:1593:2: note: here
case PRCM_DSI_PLLOUT_SEL_PHI_2:
^~~~
drivers/mfd/db8500-prcmu.c:1594:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
div *= 2;
~~~~^~~~
drivers/mfd/db8500-prcmu.c:1595:2: note: here
case PRCM_DSI_PLLOUT_SEL_PHI:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
device_node_to_regmap() is exactly like syscon_node_to_regmap(), but it
does not check that the node is compatible with "syscon", and won't
attach the first clock it finds to the regmap.
The rationale behind this, is that one device node with a standard
compatible string "foo,bar" can be covered by multiple drivers sharing a
regmap, or by a single driver doing all the job without a regmap, but
these are implementation details which shouldn't reflect on the
devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
Cc: Mathieu Malaterre <malat@debian.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20190706164722.18766-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20190706164722.18766-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20190706164722.18766-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building davinci as multiplatform, we get a build error
in this file:
drivers/mfd/davinci_voicecodec.c:22:10: fatal error: 'mach/hardware.h' file not found
The header is only used to access the io_v2p() macro, but the
result is already known because that comes from the resource
a little bit earlier.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Set 'struct device' fwnode when registering a new device
- New Drivers
- Add support for ROHM BD70528 PMIC
- New Device Support
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
- New Functionality
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
- Fix-ups
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
- Bug Fixes
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera
-----BEGIN PGP SIGNATURE-----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=A3jw
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Set 'struct device' fwnode when registering a new device
New Drivers:
- Add support for ROHM BD70528 PMIC
New Device Support:
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
New Functionality:
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
Fix-ups:
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
Bug Fixes:
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera"
* tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: hi655x-pmic: Fix missing return value check for devm_regmap_init_mmio_clk
mfd: madera: Fixup SPDX headers
mfd: madera: Remove some unused registers and fix some defaults
mfd: intel-lpss: Release IDA resources
mfd: intel-lpss: Add Intel Elkhart Lake PCH PCI IDs
mfd: cs5535-mfd: Remove ifdef OLPC noise
mfd: stmfx: Fix macro definition spelling
dt-bindings: mfd: Add link to ROHM BD71847 Datasheet
MAINAINERS: Swap words in INTEL PMIC MULTIFUNCTION DEVICE DRIVERS
mfd: cros_ec_dev: Register cros_ec_accel_legacy driver as a subdevice
mfd: rk808: Prepare rk805 for poweroff
mfd: rk808: Check pm_power_off pointer
mfd: cros_ec: differentiate SCP from EC by feature bit
dt-bindings: Add binding for cros-ec-rpmsg
mfd: madera: Add Madera core support for CS47L92
mfd: madera: Add Madera core support for CS47L15
mfd: madera: Update DT bindings to add additional CODECs
mfd: madera: Add supply mapping for MICVDD
mfd: madera: Fix potential uninitialised use of variable
mfd: madera: Fix bad reference to pinctrl.txt file
...
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Marek Szyprowski