The firmware files can be quite large and allocating the whole firmware
a single DMA safe buffer can be problematic if the system is under a
high memory load. Ease the requirements slightly by writing the firmware
out in page sized chunks.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It can be useful for debugging purposes to see at what point the DSP has
powered down, so add a message to inform us of this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the start of booting the DSP to earlier in the DAPM process, and
move the final starting of the DSP to later in the DAPM process. This
allows us to overlap some of the processing with other components of the
system being brought up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the ADSP2 boot proceedure into a work structure in preparation for
running it asynchronously with the reset of the audio path bring up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some devices are getting very close to the limit whilst polling the RAM
start, this patch adds a small delay to this loop to give a longer
startup timeout.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This will allow a marginal speed improvement when used with a bus that
supports async I/O by reducing the amount of context thrashing between
writes, allowing the bus to be more fully utilised.
Signed-off-by: Mark Brown <broonie@linaro.org>
When locating the memory region relating to a coefficient block written
through a bin file we keep processing the list of regions even after we
have found the region we require. This patch adds a break, so we don't
process redundant list items.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch does:
- Move the sanity check with WARN_ON() in wm_adsp_region_to_reg() and
remove the checks in the callers,
- Fix wrong WARN_ON() usages, replaced with WARN(),
- Fix unreachable or wrong BUG_ON() usages and replace with WARN_ON().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pad the ADSP word (3 bytes) to 4 bytes in the kernel and calculate
lengths based on padded ADSP words instead of treating them as bytes
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Do it in a similar fashion as we do for ADSP2.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to hold on to the `codec' pointer. We can use the `dsp'
pointer and grab all the information we need from there. This
makes the parameters for the functions a bit more sane and idiomatic.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Get rid off the wm_coeff struct and the wm_coeff_add_kcontrol()
function. We are now using the snd_soc_card_kcontrol() function to
get the kcontrol pointers. No need to call into ALSA code to
register the kcontrols.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reported-by: Dennis May <dennis.may@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rename `dirty' to `set' as it is a bit more descriptive. A set
control is any control that has been set by the user. We need to ensure
that everytime we boot the DSP we sync out any controls that were
set.
We could at some point start keeping track of the default values of
the controls to suppress some of the device I/O.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are two return paths which don't kfree(name).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add initial support for runtime tuning for the ADSP cores. This
is achieved by exposing the coefficient configuration blocks as
ALSA binary controls.
The current code assumes that no controls on the DSP are volatile.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Firmwares may provide some firmware wide configuration regions which can
be configured by the coefficient files using the firmware ID as the
algorithm ID, include these in the algorithm list.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we have regular register mapped controls we should be splitting
the control sets for ADSP1 and ADSP2 as the register maps are not
identical. Do that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since ASoC does not yet really have the framework features needed to
support propagating sample rates through the device well yet implement
basic support for the ISRCs equivalent to that we currently have for the
ASRCs. The user can opt for 8kHz or 16kHz as the rate for the DSP blocks
in addition to the main audio rate, these being the primary use cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Older .bin files report the global coefficients as absolute address writes
to zero; maintain compatibility with them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
'file' is malloced in wm_adsp_load_coeff() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the regmap API to use asynchronous I/O where supported to minimise
the delay between transfers, reducing firmware download times.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Maximise robustness for the widest range of firmwares by ensuring the DSP
is in a consistent state when halted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch correctly releases the firmware if the magic string in the
firmware header does not match.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Normally kmalloc() returns things that are DMA safe so not visible on all
platforms but we do need to explicitly request DMA safe memory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Normally kmalloc() returns things that are DMA safe so not visible on all
platforms but we do need to explicitly request DMA safe memory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Charles Keepax