A lot of headsets/headphones have a "Speaker" mixer control. This confuses
PulseAudio to think it is a speaker instead of a headphone/headset.
Therfore, we rename it to "Headphone".
We determine if something is a headphone similar to how udev determines
form factor (see 78-sound-card.rules).
BugLink: https://bugs.launchpad.net/bugs/1082357
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The playback endpoint uses implicit feedback mode, similar
to the M-Audio FTU. Like with the FTU, we need to associate
the sync pipe ourselves.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add ranges for various Fast Track C400 controls, as observed
while using the vendor's mixer control software (res values
are an estimation).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds the unit ID and the control as parameters to the creation of the
effect unit control for the M-Audio Fast Track Ultra. This allows the
code to be shared with other devices that use different unit ID and
control, such as the M-Audio Fast Track C400.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current code mishandles the case where the device is a UAC2
and the bDescriptorSubtype is a UAC2 Effect Unit (0x07).
It tries to parse it as a Processing Unit (which is similar to two
other UAC1 units with overlapping subtypes), but since the structure
is different (See: 4.7.2.10, 4.7.2.11 in UAC2 standard), the parsing
is done incorrectly and prevents the device from initializing.
For now, just ignore the unit.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, channel IDs exceeding 31 (0x1f) cannot be used.
The channel ID is derived from the cmask. Extending cmask
to a 64-bit type would only allow it to go up to 63 (0x3f).
Some devices have channel IDs exceeding that as well.
To address that, add an offset to the mixer element which
is then accounted for in the UAC set/get functions.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For implicit feedback endpoints, the number of bytes for each packet
is matched by the corresponding synchronizing endpoint.
The size is calculated by taking the actual size and dividing it by
the stride - currently by the endpoint's stride, but we should use the
synchronization source's stride.
This is evident when the number of channels differ between the
synchronization source and the implicitly fed-back endpoint, as with
M-Audio Fast Track C400 - the synchronization source (capture)
has 4 channels, while the implicit feedback mode endpoint has 6.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removed unnecessary labels probably left out of some previous cleanup.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As the I2S src clks are registered with clkdev using generic
connection id, driver can get the clk name using generic id.
So the variable representing the array of rclk src clks is
deleted.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the jack detection inforamtion as bool from devicetree.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
devm_regmap_init_i2c() is device managed and makes error
handling and code cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
devm_regmap_init_i2c() is device managed and makes error
handling and code cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
devm_regmap_init_i2c() is device managed and makes error
handling and code cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
devm_regulator_bulk_get() is device managed and makes error
handling and code cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
devm_regulator_bulk_get() is device managed and makes error
handling and code cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
devm_regulator_bulk_get() is device managed and makes error
handling and code cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
devm_regulator_bulk_get() is device managed and makes error
handling and code cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some ADSP devices can make use of DVFS to optimise power consumption
depending on the operating frequency of the DSP core. Implement
support for this in the generic ADSP code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a haptics widget for use by the haptics driver and expose the DAPM
context for it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a haptics widget for use by the haptics driver and expose the DAPM
context for it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Arizona CODECs contain a haptics module providing vibration feedback
support. Implement basic support for this, providing simple start/stop and
signal magnitude control.
Since the output path for haptics is routed through the CODEC audio routing
it is modelled as a signal generator within ASoC, the haptics driver calls
DAPM to start and stop the output drivers. An appropriate output path must
be configured via ALSA to connect the haptics source to the correct output.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some other device functions need to integrate with signal sources in the
audio portion (primarily for haptics) so allow CODEC to export the DAPM
context by pointing to it from the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a preliminary patch for introducing a protection to access
races of snd_array instances. Call snd_array_init() appropriately
at the initialization time and don't call it twice.
Also the allocations of codec-spec structs are cleaned up by helper
functions in patch_sigmatel.c and patch_analog.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We cannot include any plat or mach headers for the multiplatform
support.
Fix the issue by defining local mcbsp_omap1().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Hi Mark,
thanks your insisting on a better description for the patch, I found a
more appropriate solution for the problem:
Compiling the SoC Audio driver for Freescale i.MX as a module
(CONFIG_SND_SOC_IMX_PCM=m) results in a non-functional sound driver
indicated by the error message:
| imx-sgtl5000 sound.1: platform imx-pcm-audio not registered
| imx-sgtl5000 sound.1: snd_soc_register_card failed (-517)
| platform sound.1: Driver imx-sgtl5000 requests probe deferral
instead of the message:
| imx-sgtl5000 sound.1: sgtl5000 <-> 63fcc000.ssi mapping ok
that is to be expected upon loading the snd-soc-imx-pcm.ko module.
The build log reveals, that the file imx-pcm-dma.o (or imx-pcm-fiq.o
depending on the kernel configuration), which should be linked
together with imx-pcm.o into snd-imx-pcm.ko, is not being compiled in
this case.
The make rules for these files shows that the target object imx-pcm.o
is assigned to the variable snd-soc-imx-pcm-y while
imx-pcm-{dma,fiq}.o are added to to
snd-soc-imx-pcm-$(CONFIG_SND_SOC_IMX_PCM_DMA) and
snd-soc-imx-pcm-$(CONFIG_SND_SOC_IMX_PCM_FIQ) which resolve to
snd-soc-imx-pcm-m in this case.
According to Documentation/kbuild/modules.txt:
|When the module is built from multiple sources, an additional line is
|needed listing the files:
|
| <module_name>-y := <src1>.o <src2>.o ...
Thus the type of the config variables CONFIG_SND_SOC_IMX_PCM_DMA and
CONFIG_SND_SOC_IMX_PCM_FIQ should be 'bool' instead of 'tristate' to
resolve to 'y' when selected.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to a broken make rule, sound/soc/fsl/imx-pcm-dma.c or
sound/soc/fsl/imx-pcm-fiq.c (whatever is selected via Kconfig) will
not be compiled into imx-pcm.o when building as module, i.e.:
CONFIG_SND_SOC_IMX_PCM=m
CONFIG_SND_SOC_IMX_PCM_DMA=m
resulting in a non-functional sound driver.
This gives the error messages:
| imx-sgtl5000 sound.1: platform imx-pcm-audio not registered
| imx-sgtl5000 sound.1: snd_soc_register_card failed (-517)
| platform sound.1: Driver imx-sgtl5000 requests probe deferral
when loading the driver instead of what's to be expected:
| imx-sgtl5000 sound.1: sgtl5000 <-> 63fcc000.ssi mapping ok
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The device should not be generating interrupts when it does not have power
so ignore incoming interrupts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't rely on the kcontrol for robustness reasons, the widget mechanism
is what the framework uses.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the support for channel maps of the PCM streams on USB audio
devices. The channel map information is already found in
ChannelConfig descriptor entries, which haven't been referred until
now.
Each chmap entry is added to audioformat list entry and copied to TLV
dynamically instead of creating a whole chmap array.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull powerpc EEH bugfixes from Benjamin Herrenschmidt.
Two one-liner fixes for the new EEH code.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/eeh: Do not invalidate PE properly
powerpc/pseries: Fix oops with MSIs when missing EEH PEs
Pull MIPS fixes from Ralf Baechle:
"Three issues fixed accross the field:
- Some functions that were recently outlined as part of a preemption
fix were causing problems with function tracing.
- The recently merged in-kernel MPI library uses very outdated
headers that contain MIPS-specific code which won't build on with
gcc 4.4 or newer.
- The MIPS non-NUMA memory initialization was making only a very
half-baked attempt at merging adjacent memory ranges. This kept
the code simple enough but is now causing issues with kexec."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
While the EEH does recovery on the specific PE that has PCI errors,
the PCI devices belonging to the PE will be removed and the PE will
be marked as invalid since we still need the information stored in
the PE. We only invalidate the PE when it doesn't have associated
EEH devices and valid child PEs. However, the code used to check
that is wrong. The patch fixes that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
David Henningsson