These macros are applicable to pre-AR9003 chips
and the addresses are different for the AR9003
family. Since they are unused anyway, remove them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the number of patterns that can be configured in
the HW is higher for newer chips, store the chip-specific
value in ath9k_hw_wow.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be used to hold the WOW state in
ath9k_hw.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to allocate a new structure and
free it for every user pattern, instead use local
variables.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be used to force WOW for cards that
are not present in the supported PCI ID list.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Printing the value of the wakeup status is sufficient.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The various variables tracking bmiss interrupts
are not really used anywhere except in a debug
message. Remove them since they have no functional
purpose.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch makes sure that valid WOW triggers
are present before trying to suspend the device.
Also, introduce and use ATH_OP_WOW_ENABLED to
bypass PCI suspend and clear it in resume().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Registering the card as a wakeup source needs to
be done once, during initialization. When the WOW
configuration changes, the card's status as wakeup
source needs to be changed too and this is done
via the set_wakeup() callback. Also, make sure
the device is removed properly using ath9k_deinit_wow().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If CONFIG_ATH9K_CHANNEL_CONTEXT is enabled, check whether
multiple contexts are active and if so, return 1 without
enabling WOW since we don't support it in this case.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If multiple interfaces are active or there is no
associated station interface, bail out early and
return 1 so that mac80211 can proceed with the normal
suspend routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WOW capability is registered with mac80211 only when
the device has the ability to wakeup, so there is no
need to check in the suspend() routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not try to cancel work instances and ANI when
the device is not present or WOW triggers are
not configured. Bail out early and use ath_err()
for such error conditions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enabling WOW based on the chip is incorrect since
it needs to be done for specific sub-devices which
have proper platform support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When AP is started, firmware exits power save mode. This
means power save manager of AP takes priority over station.
Firmware stop sending periodic AWAKE events to host.
We may have UAPSD enabled on station which buffers data
packets until AWAKE event from firmware. Data path is
unnecessarily blocked in this case. This patch disables
UAPSD mode to reenable transmit data path.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch makes sure that skb is freed after downloading
NULL packet in error cases. Also, USB chipsets return
-EINPROGRESS after downloading packets, they are freed in
USB completion handler later. We will add missing change
to set tx_lock_flag for USB which blocks further packets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory is leaked after downloading already processed packet. This
patch fixes the problem by freeing returned skb. Other transmit
paths don't have this problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wakeup timer is in sync with 'pm_wakeup_fw_try' flag. It
has been started instead of cancelling at one place. This
patch corrects it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are instances where the DMA engine stalls. The new code detects
such stalls and restarts DMA without needing a power reset.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware supplies two kinds of packets via the RX mechanism. Besides the
normal data received over the air, these packets may contain bluetooth status
and other information. The present code fails to detect which kind of
information was received.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initially, the routine to update the write point in the FIFO buffer was
coded to save CPU time by not doing the calculation every interrupt. This
was an error and results in TX hangs.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the buffer descriptor index exceeds 2, then a TX HANG condition
will result.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The quota threshold should be reduced to 4 to update the
firmware more frequently.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After commit e9d8b2c296 (xen-netback:
disable rogue vif in kthread context), a fatal (protocol) error would
leave the guest Rx thread spinning, wasting CPU time. Commit
ecf08d2dbb (xen-netback: reintroduce
guest Rx stall detection) made this even worse by removing a
cond_resched() from this path.
Since a fatal error is non-recoverable, just allow the guest Rx thread
to exit. This requires taking additional refs to the task so the
thread exiting early is handled safely.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Julien Grall <julien.grall@linaro.org>
Tested-by: Julien Grall <julien.grall@linaro.org>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de966c5928 (net/mlx4_core: Support more than 64 VFs) was meant to
allow up to 126 VFs. However, due to leaving MLX4_MFUNC_MAX too low, using
more than 80 VFs resulted in memory corruptions (and Oopses) when more than
80 VFs were requested. In addition, the number of slaves was left too high.
This commit fixes these issues.
Fixes: de966c5928 ("net/mlx4_core: Support more than 64 VFs")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Add support for IEEE ets & pfc api.
* Fix bug that resulted in incorrect bandwidth percentage being returned for
CEE peers
* Convert pfc enabled info from firmware format to what dcbnl expects before
returning
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM has 32-byte cache lines, which according to the comment in
the init registers function seems to work best with the default
value of 0x4800 that is also used on sparc and parisc.
This adds ARM to the same list, to use that default but no
longer warn about it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hip04 ethernet driver causes a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/hisilicon/hip04_eth.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug where vnet_skb_shape() didn't set the already-selected
queue mapping when a packet copy was required. This results in using the
wrong queue index for stops/starts, hung tx queues and watchdog timeouts
under heavy load.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qlge_update_hw_vlan_features() will always first put the
interface down, then update features and then bring it up again. But it
is possible to hit this code while the adapter is down and this causes a
non-paired call to napi_disable(), which will get stuck.
This patch fixes it by skipping these down/up actions if the interface
is already down.
Fixes: a45adbe8d3 ("qlge: Enhance nested VLAN (Q-in-Q) handling.")
Cc: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for retrieving port level statistics from device.
Hook is added for ethtool's stats functionality. For example,
$ ethtool -S eth3
NIC statistics:
rx_packets: 12
rx_bytes: 2790
rx_dropped: 0
rx_errors: 0
tx_packets: 8
tx_bytes: 728
tx_dropped: 0
tx_errors: 0
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ndo_bridge_setlink and ndo_bridge_dellink handlers point
to the default switchdev handlers
This follows my bonding driver changes.
I have only compile tested this patch. However similar
bonding code has been tested.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want bond to pick up the offload flag if any of its slaves have it.
NETIF_F_HW_SWITCH_OFFLOAD flag is added to the mask, so that
netdev_increment_features does not ignore it.
This also adds ndo_bridge_setlink and ndo_bridge_dellink handlers.
These currently point to the default handlers provided by the
switchdev api.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the NETIF_F_HW_SWITCH_OFFLOAD feature flag on rocker ports
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- In tx_hard_error_bump_tc interrupt, tc should be bumped only when current
device instance is in DMA threshold mode. Check per device xstats.threshold
other than global tc.
- Set per device xstats.threshold to SF_DMA_MODE when current device
instance is set to SF mode.
v2-changes:
- fix ident style
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit dc9daab226 ("cxgb4: Added support in debugfs to dump
sge_qinfo") a preprocessor check for CONFIG_CXGB4_DCB got added, which should
have been CONFIG_CHELSIO_T4_DCB. After adding the right preprocessor, build
fails due to missing function ethqset2pinfo. Fixing that as well.
V2: Updated description since the patch also fixes build failure
Reported-by: Paul Bolle <pebolle@tiscal.nl>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the warnings (space before , ) shown by
checkpatch.pl
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces the shifting operations by BIT macro
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By using only the usb interface number for the rfkill name, we might
have a name conflicts in case two similar hso devices are connected.
In this patch, the name of the hso rfkill interface embed the value
of a counter that is incremented each time a new rfkill interface is
added.
Suggested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hso serial devices, two cancel_work_sync were missing in the
disconnect method.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serial_table is used to map the minor number of the usb serial device
to its associated context. The table is updated in the probe method and
in hso_serial_ref_free() which is called either from the tty cleanup
method or from the usb disconnect method.
This patch ensures that the serial_table is updated in the disconnect
method and no more from the cleanup method to avoid the following
potential race condition.
- hso_disconnect() is called for usb interface "x". Because the serial
port was open and because the cleanup method of the tty_port hasn't
been called yet, hso_serial_ref_free() is not run.
- hso_probe() is called and fails for a new hso serial usb interface
"y". The function hso_free_interface() is called and iterates
over the element of serial_table to find the device associated to
the usb interface context.
If the usb interface context of usb interface "y" has been created
at the same place as for usb interface "x", then the cleanup
functions are called for usb interfaces "x" and "y" and
hso_serial_ref_free() is called for both interfaces.
- release_tty() is called for serial port linked to usb interface "x"
and possibly crash because the tty_port structure contained in the
hso_device structure has been freed.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function hso_serial_common_free() is called either by the cleanup
method of the tty or by the usb disconnect method.
In the former case, the usb_disconnect() has been already called
and the sysfs group associated to the device has been removed.
By calling tty_unregister directly from the usb_disconnect() method,
we avoid a warning due to the removal of the sysfs group of the usb
device.
Example of warning:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 778 at fs/sysfs/group.c:225 sysfs_remove_group+0x50/0x94()
sysfs group c0645a88 not found for kobject 'ttyHS5'
Modules linked in:
CPU: 0 PID: 778 Comm: kworker/0:3 Tainted: G W 3.18.0+ #105
Workqueue: events release_one_tty
[<c000dfe4>] (unwind_backtrace) from [<c000c014>] (show_stack+0x14/0x1c)
[<c000c014>] (show_stack) from [<c0016bac>] (warn_slowpath_common+0x5c/0x7c)
[<c0016bac>] (warn_slowpath_common) from [<c0016c60>] (warn_slowpath_fmt+0x30/0x40)
[<c0016c60>] (warn_slowpath_fmt) from [<c00ddd14>] (sysfs_remove_group+0x50/0x94)
[<c00ddd14>] (sysfs_remove_group) from [<c0221e44>] (device_del+0x30/0x190)
[<c0221e44>] (device_del) from [<c0221fb0>] (device_unregister+0xc/0x18)
[<c0221fb0>] (device_unregister) from [<c0221fec>] (device_destroy+0x30/0x3c)
[<c0221fec>] (device_destroy) from [<c01fe1dc>] (tty_unregister_device+0x2c/0x5c)
[<c01fe1dc>] (tty_unregister_device) from [<c029a428>] (hso_serial_common_free+0x2c/0x88)
[<c029a428>] (hso_serial_common_free) from [<c029a4c0>] (hso_serial_ref_free+0x3c/0xb8)
[<c029a4c0>] (hso_serial_ref_free) from [<c01ff430>] (release_one_tty+0x30/0x84)
[<c01ff430>] (release_one_tty) from [<c00271d4>] (process_one_work+0x21c/0x3c8)
[<c00271d4>] (process_one_work) from [<c0027758>] (worker_thread+0x3d8/0x560)
[<c0027758>] (worker_thread) from [<c002be4c>] (kthread+0xc0/0xcc)
[<c002be4c>] (kthread) from [<c0009630>] (ret_from_fork+0x14/0x24)
---[ end trace cb88537fdc8fa208 ]---
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for a dedicated reset work in the hso driver since
there is already a reset work foreseen in usb_interface that does
the same.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In other functions of the driver, variables of type "struct hso_serial"
are denoted by "serial" and variables of type "struct hso_device" are
denoted by "hso_dev". This patch makes the hso_free_interface()
consistent with these notations.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the rfkill interface was created, a buffer containing the name
of the rfkill node was allocated. This buffer was never freed when the
device disappears.
To fix the problem, we put the name given to rfkill_alloc() in
the hso_net structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the disconnect path, tx_buffer should freed like tx_data to avoid
a memory leak when the device disconnects.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device disappear, the function hso_disconnect() is called to
perform cleanup. In the cleanup function, hso_free_interface() calls
tty_port_tty_hangup() in view of scheduling a work to hang up the tty if
needed. If the port was not open then hso_serial_ref_free() is called
directly to cleanup everything. Otherwise, hso_serial_ref_free() is called
when the last fd associated to the port is closed.
For each open port, tty_release() will call the close method,
hso_serial_close(), which drops the last kref and call
hso_serial_ref_free() which unregisters, destroys the tty port
and finally frees the structure in which the tty_port structure
is included. Later, in tty_release(), more precisely when release_tty()
is called, the tty_port previously freed is accessed to cancel
the tty buf workqueue and it leads to a crash.
In view of avoiding this crash, we add a cleanup method that is called
at the end of the hangup process and we drop the last kref in this
function when all the ports have been closed, when tty_port is no
more needed and when it is safe to free the structure containing the
tty_port structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
No timer related function is used in this driver.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the chanel hw_value and not the center frequency when
building channel array for scan_config_cmd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable EBS on one shot scans if supported by FW.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When iwl_mvm_power_update_mac() is called, we have already added the
mac context, so if this call fails we should remove the mac.
CC: <stable@vger.kernel.org> [3.15+]
Fixes: commit e5e7aa8e25 ('iwlwifi: mvm: refactor power code')
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Last EBS status wasn't set to success in the initialization, which
caused the first scan to be without EBS. Fix that.
When EBS is not enabled by the driver, the FW still sends ebs_status success,
which can override EBS failure state. Consider only EBS failures, to avoid
such override. Last_ebs_success is set back to true upon disconnection.
Last_ebs_success wasn't set in umac scan abort flow, fix that too.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Different queue can have different behavior. While it can be
unacceptable for a certain queue to be stuck for 2 seconds
(e.g. the command queue), it can happen that another queue
will stay stuck for even longer (a queue servicing a power
saving client in GO).
The op_mode can even make the timeout be a function of the
listen interval.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This watchdog allows to monitor the transmit queues. When a
queue doesn't progress for a too long time, a timer fires
and then, debug data can be collected.
This watchdog has never been enabled on dvm controlled
devices, so don't enable it there.
In order to have it running on mvm controlled devices, we
need to fix a small issue in the transport layer: mvm
controlled devices use the shadow registers optimization.
In this case, the watchdog wasn't running at all, even if
enabled by the module parameter. Fix that on the way.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
During out-of-channel activities (e.g. scan) TDLS ch-switch responses from
a peer are kept in FW. These packets arrive only after the out-of-channel
activity is complete, which can be in the order of several seconds.
Since TDLS ch-sw has no dialog-token-like mechanism for distinguishing
sessions, use the GP2 time of the incoming ch-switch response to discern
validity. For this purpose record the GP2 time of an outgoing TDLS ch-sw
request and compare to the Rx time of the ch-sw response.
The methods works in practice since the GP2 time of FW-deferred Rx is
accurate and contains the real Rx timestamp.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a response-received state and add more limits on allowed requests
in each state of the connection. Previously ch-switch requests from
other peers could interrupt an outgoing active ch-switch. Also stale
packets from the current peer could disrupt the channel switch state.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The base address of the scheduler in the device's memory
(SRAM) comes from two different sources. The periphery
register and the alive notification from the firmware.
We have a check in iwl_pcie_tx_start that ensures that
they are the same.
When we resume from WoWLAN, the firmware may have crashed
for whatever reason. In that case, the whole device may be
reset which means that the periphery register will hold a
meaningless value. When we come to compare
trans_pcie->scd_base_addr (which really holds the value we
had when we loaded the WoWLAN firmware upon suspend) and
the current value of the register, we don't see a match
unsurprisingly.
Trick the check to avoid a loud yet harmless WARN.
Note that when the WoWLAN has crashed, we will see that
in iwl_trans_pcie_d3_resume which will let the op_mode
know. Once the op_mode is informed that the WowLAN firmware
has crashed, it can't do much besides resetting the whole
device.
CC: <stable@vger.kernel.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some devices have 31 TFD queues. Don't enable it yet since
there are still issues with it, but at least prepare the
code for it. There was a bug in the read pointer assignment,
fix that. Also, move the inline functions to iwl-scd.h which
is the right place.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In certain testing scenarios we'd like to force a decision
between STBC/BFER/SISO. In the normal scenario this decision
is done by the FW. Enable this option vis debugfs.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
VHT Beamformer (BFER) will be used if the peer supports it
and there's a benefit to use it vs. STBC or SISO.
The driver now tells the FW whether BFER and/or STBC are
allowed but the FW will make the decision to use either
or stick to SISO on its own.
BFER is limited to a single remote peer. The driver takes
care of ensuring this to the FW and prioritizes with which
peer BFER will be used.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Printing all the scratch data of the TFDs of that queue is
useless and stuffed the kernel log with data. Remove that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We don't really need to use different mac colors when adding mac
contexts, because they're not used anywhere. In fact, the firmware
doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401
when we reach that.
Remove the color increment to use always zero and avoid reaching 255.
CC: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There's really no reason to pad out the field with spaces at the
end of the line - they're practically invisible there anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we don't want to restart the firmware, don't reprobe either in case
of a failure during reconfiguration. This allows us to debug failures
in the reconfig flow as well.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
NetCP on Keystone has cpsw ale function similar to other TI SoCs
and this driver is re-used. To allow both ti cpsw and keystone netcp
to re-use the driver, convert the cpsw ale to a module and configure
it through Kconfig option CONFIG_TI_CPSW_ALE. Currently it is statically
linked to both TI CPSW and NetCP and this causes issues when the above
drivers are built as dynamic modules. This patch addresses this issue
While at it, fix the Makefile and code to build both netcp_core and
netcp_ethss as dynamic modules. This is needed to support arm allmodconfig.
This also requires exporting of API calls provided by netcp_core so that
both the above can be dynamic modules.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing code frees the skb in EAGAIN case, in which the skb will be
retried from upper layer and used again.
Also, the existing code doesn't free send buffer slot in error case, because
there is no completion message for unsent packets.
This patch fixes these problems.
(Please also include this patch for stable trees. Thanks!)
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following kernel crash,
WARNING: CPU: 2 PID: 0 at net/ipv4/tcp_input.c:3079 tcp_clean_rtx_queue+0x658/0x80c()
Call trace:
[<fffffe0000096b7c>] dump_backtrace+0x0/0x184
[<fffffe0000096d10>] show_stack+0x10/0x1c
[<fffffe0000685ea0>] dump_stack+0x74/0x98
[<fffffe00000b44e0>] warn_slowpath_common+0x88/0xb0
[<fffffe00000b461c>] warn_slowpath_null+0x14/0x20
[<fffffe00005b5c1c>] tcp_clean_rtx_queue+0x654/0x80c
[<fffffe00005b6228>] tcp_ack+0x454/0x688
[<fffffe00005b6ca8>] tcp_rcv_established+0x4a4/0x62c
[<fffffe00005bf4b4>] tcp_v4_do_rcv+0x16c/0x350
[<fffffe00005c225c>] tcp_v4_rcv+0x8e8/0x904
[<fffffe000059d470>] ip_local_deliver_finish+0x100/0x26c
[<fffffe000059dad8>] ip_local_deliver+0xac/0xc4
[<fffffe000059d6c4>] ip_rcv_finish+0xe8/0x328
[<fffffe000059dd3c>] ip_rcv+0x24c/0x38c
[<fffffe0000563950>] __netif_receive_skb_core+0x29c/0x7c8
[<fffffe0000563ea4>] __netif_receive_skb+0x28/0x7c
[<fffffe0000563f54>] netif_receive_skb_internal+0x5c/0xe0
[<fffffe0000564810>] napi_gro_receive+0xb4/0x110
[<fffffe0000482a2c>] xgene_enet_process_ring+0x144/0x338
[<fffffe0000482d18>] xgene_enet_napi+0x1c/0x50
[<fffffe0000565454>] net_rx_action+0x154/0x228
[<fffffe00000b804c>] __do_softirq+0x110/0x28c
[<fffffe00000b8424>] irq_exit+0x8c/0xc0
[<fffffe0000093898>] handle_IRQ+0x44/0xa8
[<fffffe000009032c>] gic_handle_irq+0x38/0x7c
[...]
Software writes poison data into the descriptor bytes[15:8] and upon
receiving the interrupt, if those bytes are overwritten by the hardware with
the valid data, software also reads bytes[7:0] and executes receive/tx
completion logic.
If the CPU executes the above two reads in out of order fashion, then the
bytes[7:0] will have older data and causing the kernel panic. We have to
force the order of the reads and thus this patch introduces read memory
barrier between these reads.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbevf_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.
Use first->protocol instead of skb->protocol to get the proper network
protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbe_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.
Use vlan_get_protocol() to get the proper network protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
igbvf_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.
Use vlan_get_protocol() to get the proper network protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are all either written once or extremly rarely (e.g. from init
code), so we can move them to the .data..read_mostly section.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like on 3517 davinci_emac MAC address registers have a
different layout compared to dm816x and am33xx.
Let's add a function to get the 3517 MAC address.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on dm81xx, we can get the davinci_emac MAC address the same
way as on am33xx cpsw.
Let's also use ether_addr_copy() for davinci_emac while at it.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like davinci_emac and cpsw can share some code although the
device registers have a different layout.
At least the code for getting the MAC address using syscon can
be shared by passing the register offset. Let's start with that
and set up a minimal shared cpsw-shared.c.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch tried to work around a valid warning for the use of a
deprecated interface by blindly changing from the old
pcmcia_request_exclusive_irq() interface to pcmcia_request_irq().
This driver has an interrupt handler that is not currently aware
of shared interrupts, but can be easily converted to be.
At the moment, the driver reads the interrupt status register
repeatedly until it contains only zeroes in the interesting bits,
and handles each bit individually.
This patch adds the missing part of returning IRQ_NONE in case none
of the bits are set to start with, so we can move on to the next
interrupt source.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5f5316fcd0 ("am2150: Update nmclan_cs.c to use update PCMCIA API")
Signed-off-by: David S. Miller <davem@davemloft.net>
The ni65 and lance ethernet drivers manually program the ISA DMA
controller that is only available on x86 PCs and a few compatible
systems. Trying to build it on ARM results in this error:
ni65.c: In function 'ni65_probe1':
ni65.c:496:62: error: 'DMA1_STAT_REG' undeclared (first use in this function)
((inb(DMA1_STAT_REG) >> 4) & 0x0f)
^
ni65.c:496:62: note: each undeclared identifier is reported only once for each function it appears in
ni65.c:497:63: error: 'DMA2_STAT_REG' undeclared (first use in this function)
| (inb(DMA2_STAT_REG) & 0xf0);
The DMA1_STAT_REG and DMA2_STAT_REG registers are only defined for
alpha, mips, parisc, powerpc and x86, although it is not clear
which subarchitectures actually have them at the correct location.
This patch for now just disables it for ARM, to avoid randconfig
build errors. We could also decide to limit it to the set of
architectures on which it does compile, but that might look more
deliberate than guessing based on where the drivers build.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cosa driver is rather outdated and does not get built on most
platforms because it requires the ISA_DMA_API symbol. However
there are some ARM platforms that have ISA_DMA_API but no virt_to_bus,
and they get this build error when enabling the ltpc driver.
drivers/net/wan/cosa.c: In function 'tx_interrupt':
drivers/net/wan/cosa.c:1768:3: error: implicit declaration of function 'virt_to_bus'
unsigned long addr = virt_to_bus(cosa->txbuf);
^
The same problem exists for the Hostess SV-11 and Sealevel Systems 4021
drivers.
This adds another dependency in Kconfig to avoid that configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cs89x0 driver can either be built as an ISA driver or a platform
driver, the choice is controlled by the CS89x0_PLATFORM Kconfig
symbol. Building the ISA driver on a system that does not have
a way to map I/O ports fails with this error:
drivers/built-in.o: In function `cs89x0_ioport_probe.constprop.1':
:(.init.text+0x4794): undefined reference to `ioport_map'
:(.init.text+0x4830): undefined reference to `ioport_unmap'
This changes the Kconfig logic to take that option away and
always force building the platform variant of this driver if
CONFIG_HAS_IOPORT_MAP is not set. This is the only correct
choice in this case, and it avoids the build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PZQW
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.20-20150128' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-28-01
this is a pull request of 12 patches for net-next/master.
There are 3 patches by Ahmed S. Darwish, which update the kvaser_usb
driver and add support for the USBcan-II based adapters. Stéphane
Grosjean contributes 7 patches for the peak_usb driver, which add
support for the CANFD USB adapters. I contribute 2 patches which clean
up the peak_usb driver structure a bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cd1e65044d ("of/device: Don't register disabled
devices"), the disabled device will not be registered at all. So we
don't need to do the check again in the platform device driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we've run out of space in the output buffer to store more data, we
will call zlib_deflate with a NULL output buffer until we've consumed
remaining input.
When this happens, olen contains the size the output buffer would have
consumed iff we'd have had enough room.
This can later cause skb_over_panic when ppp_generic skb_put()s
the returned length.
Reported-by: Iain Douglas <centos@1n6.org.uk>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the netns to src_net to avoid confusion with the netns where the
interface stands. The user may specify IFLA_NET_NS_[PID|FD] to create
a x-netns netndevice: IFLA_NET_NS_[PID|FD] points to the netns where the
netdevice stands and src_net to the link netns.
Note that before commit f01ec1c017 ("vxlan: add x-netns support"), it was
possible to create a x-netns vxlan netdevice, but the netdevice was not
operational.
Fixes: f01ec1c017 ("vxlan: add x-netns support")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
src_net points to the netns where the netlink message has been received. This
netns may be different from the netns where the interface is created (because
the user may add IFLA_NET_NS_[PID|FD]). In this case, src_net is the link netns.
It seems wrong to override the netns in the newlink() handler because if it
was not already src_net, it means that the user explicitly asks to create the
netdevice in another netns.
CC: Sjur Brændeland <sjur.brandeland@stericsson.com>
CC: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Fixes: 8391c4aab1 ("caif: Bugfixes in CAIF netdevice for close and flow control")
Fixes: c412540063 ("caif-hsi: Add rtnl support")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During drv_start/drv_stop stress testing in ARM platform,
sometimes target is taking more that 5ms to wake up. Similar
behaviour also noted during driver load and unload iterations.
On such cases, the wakup duration lies between 5-6ms. Hence
increasing pci wakup timeout 10ms to be more safer. With this
changes, able to complete power down/up >100 iterations without
any issues.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable the MCS8 and MCS9 support for 2.4G band, it will
use these data rate with other devices having the same
capability.
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware revisions providing sta keepalive service
have it enabled by default.
mac80211 already does idle connection polling so
it makes no sense to duplicate this in ath10k.
mac80211 wouldn't even know of the offloaded
keepalive NullFunc frames.
This prevents sending out some extraneous frames
on the air.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 has STA keepalive
service available. The service can provide
automatic idle connection polling via NullFunc
frames to AP when acting as a client.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 supports this.
This should fix issues related to multi-vif WMM.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 supports this.
This will be used soon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 already requests WMM per vif but firmware
wasn't able to handle this until now. However new
wmi-tlv firmware for qca6174 is capable of this.
This prepares per-vif WMM param setup.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are new (not anymore?) Broadcom 802.11ac wireless cards based on
chipsets like BCM4352 and BCM4360. They use a new PHY type (called
simply AC) that will require new specific code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AC-PHY hardware includes new control 0x3 bits that need to be set to the
0x1 by default.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some AR955x/QCA953x boards, noise floor calibration
gets stuck and the cause is a hardware/BB issue. To fix
this, peak detect calibration in the HW is disabled
and is done in the driver instead. There a few differences
with the calibration routine for older chips like
AR9331.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The value is different for PCOEM cards and AR955x/AR953x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The LNA gain setting override needs to be done
only for AR9330 and PCOEM chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be used if we need to apply register settings
for all PCOEM solutions (in the AR9003 family).
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch disables HW peak detect calibration for
AR955x, since it is problematic on a few boards.
Instead, manual calibration will be done in the
driver.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch disables HW peak detect calibration for
QCA953x, since it is problematic on a few boards.
Instead, manual calibration will be done in the
driver.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
b43 has a FIXME about locking in the mac80211 set-beacon-int callback for a long time.
As it turns out there actually is a tiny race window that could result in
a use-after-free bug of the 'current_beacon' memory.
Nobody ever reported this, so it probably never happened.
Fix this by adding a spin lock that protects the current_beacon access.
We must not be in atomic context while accessing hardware (due to SDIO),
so the beacon update bottom half has to clone the skb and release the lock
before writing it to hardware.
Let's all hope that this stops the troll who is trying to submit incorrect
fixes for this issue repeatedly.
And let's hope that I'm not a troll, too, who just hides even more evil code
in an even more complex attempt to fix the issue.
Signed-off-by: Michael Buesch <m@bues.ch>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch enables 11h extensions in FW upon detecting DFS
channel in start radar detection/channel switch handlers.
Patch also takes care of disabling 11h when non DFS channels
are to be set during start_ap handler.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds cfg80211 channel_switch support for mwifiex.
Upon receiving channel switch request, driver would parse channel
switch announcement IE from beacon_data.
If TX is blocked, netdev queues are stopped. IEs from csa_beacon
are then parsed and set to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for radar_detected event from FW.
Driver in turn would stop netdev queues to stop TX traffic and
issue RADAR_DETECT event to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for channel report enabling.
Channel report event happens if radar is detected on specified channel
after driver has issued radar detect command within CAC time.
Driver in turn sends RADAR_DETECTED event to cfg80211 to tell radar was
detected within CAC time.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for cfg80211 start_radar_detection handler.
Upon reception of start_radar_detection, driver prepares radar detect
command to FW.
Delayed work is queued for CAC time which sends radar detection finished
event to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Head & Tail IEs are supposed to be added to beacon and probe response.
This patch adds separate function for parsing head and tail IEs from
cfg80211_beacon_data and sets them to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Refactor mwifiex_cfg80211_start_ap by creating separate function
to set AP channel and another for configuring other AP parameters
and starting AP.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch moves IE management routine to end of start_ap handler.
IEs now would be updated after AP has started.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Store AP configuration in private structure so that we know
current AP configuration.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When regulatory domain changes, cfg80211 already issues request
to change regulatory domain to driver via reg_notifier.
There is no need to set regulatory again during start_ap.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, we support virtual interface type change from
station<=>adhoc or station <=> p2p client/GO.
This patch adds support to change virtual interface type to
any of the type advertised in interface combinations.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to handle PS events on AP interface as well.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently interface limits are checked by seeing if bss_mode for
particular priv is set. If bss_mode is not set, interface creation
is allowed. This patch adds framework to initializes maximum virtual
interfaces supported during load time and check current number of
interfaces created agains allowed interface limit during new virtual
interface creation.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW initialization routine can also be called while changing
virtual interface types.
This patch adds bool parameter "init" to init command routine
so as to differentiate between initialization during driver load
and change virtual interface handler.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This would be used to set mac address while changing virtual
interface to different types.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wdev is used even after del_virtual_interface handler in cfg80211
in nl80211_post_doit. Since we have freed wdev in handling of
del_virtual_intf, this can result into crash while deleting
interface.
Avoid this be not declaring wdev which part of
mwifiex_private structure but struct wireless_dev type.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RTS threshold, fragmentation threshold are per device properties.
Setting them on any interface would be reflected for all other
interfaces as well. This patch removes unnesessary command download
per interface.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is not used anywhere execpt initialization.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The nvram file can hold a key=value combination in which the value
may have spaces, ie. 'RAW1=80 02 fe ff'. The parsing functionality
did not deal with this so it gives an error message:
[621746.311635] brcmfmac: brcmf_nvram_handle_key
warning: ln=90:col=11: '=' expected, skip invalid key entry
because RAW1=80 is being considerd as key=value pair and it expects
'=' sign after '02' for next key=value pair. This entry can be
completely ignored as firmware does not need it.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When revinfo retrieval fails we can not show the firmware version
in ethtool driver info. Store the result to be used when handling
ethtool driver info callback.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Obtain device revision information and store it.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some scenarios the chip number and revision may not be provided
by the bus layer. If the chip number is not filled, the common
layer will ask the firmware for this information.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introducing a define that the caller of brcmu_boardrev_str() can
use to allocate enough room for buffer passed to the function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_usb_probe_cb() the device is checked to determine whether
it is already running firmware. However, when no firmware download
is needed it still continues to request the firmware files. This
is fixed by returning after successful setup.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During suspend the bus state is put in the down state. When data
is being transmitted during this state then the netdev queue will
be close. This patch will wake the queue on state data if the
queue was closed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each bus driver is maintaing an exported bus state indicating
if upper layers can or cannot send data. SDIO is using this state
also for more private states. This makes handling the states and
state changes complex. This patch minimises the exposed states
and makes SDIO keep track of an internal state where necessary.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before going in suspend state the watchdog thread needs to put the
device in bus sleep state, which assures it can go in deep-sleep
state during D3 state.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver always called cfg80211_disconnected() with reason parameter
set to zero, ie. unknown. However, firmware does provide a valid
802.11 reason code in DEAUTH and DISASSOC event message to the driver.
This patch passes the reason code to cfg80211_disconnected().
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Control frames are normally handled outside DPC, but sometimes
within DPC. To simplify code always handle control within DPC.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the system is resumed a deadlock can occur when DPC gets
entered before resume is complete. This patch fixes this by
properly checking the suspend state outside the claim_host code
block.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On every tx the flow worker is triggered. When running high
throughput data this causes an excessive amount of times the worker
gets activated. This patch starts scheduling the worker more relaxed
once outstanding tx has reached a certain depth.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Access point require this API to check peer alive status.
Assume peer is alive when it is connected, because
firmware implements keep alive checks and will disconnect
peer if it is not alive.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement Tx status reporting using skb_complete_wifi_ack().
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Interrupt moderation parameters will never be passed as module
parameters. For product, they will be hard-coded after lab testing,
and for debugging, they can be altered via debugfs.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to HW limitation, inter-packet gap timeout max value is 13 usec.
Update of current thresholds from 15 to 13 usec.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tuning rings size for performance optimization.
Increasing Tx ring size, allows buffering more packets for HW, thus
eliminating idle periods which were observed with smaller ring at
high throughput, because HW was fetching packets faster than driver was
filling them into the TX ring. Rx ring was similarly increased to
avoid same problems in Rx.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tx queue was hard-coded to 1000 in ether_setup. Add wil_dev_setup
function which configures tx queue len to chosen default value
after calling ether_setup.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
upon cfg80211_stop_ap, a graceful AP shutdown is requested from firmware
followed by firmware reset.
In case graceful request failed, error was returned to cfg80211.
The change is to return success in this scenario, because firmware
reset will anyhow shutdown the AP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
netif_carrier_on indication was too late. In case Rx packet received
before netif_carrier_on indication, upper layers could not send
Tx packet back.
The fix is to indicate netif_carrier_on earlier:
for STA, indicate netif_carrier_on when association starts.
for AP/PCP, indicate netif_carrier_on upon starting AP/PCP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The if block was supposed to have curly braces. In the current code we
complain about dropped rx packets when we shouldn't.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the foreign page flag in netback to get the domid and grant ref
needed for the grant copy. This signficiantly simplifies the netback
code and makes netback work with foreign pages from other backends
(e.g., blkback).
This allows blkback to use iSCSI disks provided by domUs running on
the same host.
Signed-off-by: Jennifer Herbert <jennifer.herbert@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Add gnttab_alloc_pages() and gnttab_free_pages() to allocate/free pages
suitable to for granted maps.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Ballooned pages are always used for grant maps which means the
original frame does not need to be saved in page->index nor restored
after the grant unmap.
This allows the workaround in netback for the conflicting use of the
(unionized) page->index and page->pfmemalloc to be removed.
Signed-off-by: Jennifer Herbert <jennifer.herbert@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Add support for the following new PEAK-System technik CANFD USB adapters:
PCAN-USB FD single CANFD channel USB adapter
PCAN-USB Pro FD dual CANFD channels USB adapter
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a common function that pushes the skb in the network queue with adding
timestamps information, converted from time values read from the
PEAK USB adapters.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for the following new PEAK-System technik CANFD USB adapters:
PCAN-USB FD single CANFD channel USB adapter
PCAN-USB Pro FD dual CANFD channels USB adapter
The communication protocol has been developed using some mechanisms that
did exist in the PCAN-USB Pro, thus, this patch also changes some
previously static functions and data into global ones.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upgrade PEAK-System USB adapters core to the new data structures (names) and
callbacks added for the support of the CANFD extension. This specific patch
includes changes that deal with the new struct canfd_frame.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upgrade PEAK-System USB adapters core to the new data structures (names) and
callbacks added for the support of the CANFD extension. This specific patch
does the mandatory changes to support new data bittiming specs.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the definition of a new callback that enable any PEAK-System CAN USB
adapter to grant read access to its Bus Error Counters value. This ability is
not supported by all the PEAK-System adapters, thus, for those, the callback
pointer will be initiaized to NULL, which is correct regarding the linux-can
device driver specs.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Export the ctrlmode_supported value from the core file to each adapter specific
file. This has been mandatory for supporting the new CANFD extension.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A "struct peak_usb_adapter" describes a certain USB adapter, as this doesn't
change during runtime, this patch marks all USB adapter definitions as const.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the list "static struct peak_usb_adapter
*peak_usb_adapters_list[]" to be used with ARRAY_SIZE not with a NULL
termination, as the size is known during compile time.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CAN to USB interfaces sold by the Swedish manufacturer Kvaser are
divided into two major families: 'Leaf', and 'USBcanII'. From an
Operating System perspective, the firmware of both families behave
in a not too drastically different fashion.
This patch adds support for the USBcanII family of devices to the
current Kvaser Leaf-only driver.
CAN frames sending, receiving, and error handling paths has been
tested using the dual-channel "Kvaser USBcan II HS/LS" dongle. It
should also work nicely with other products in the same category.
List of new devices supported by this driver update:
- Kvaser USBcan II HS/HS
- Kvaser USBcan II HS/LS
- Kvaser USBcan Rugged ("USBcan Rev B")
- Kvaser Memorator HS/HS
- Kvaser Memorator HS/LS
- Scania VCI2 (if you have the Kvaser logo on top)
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace most of the can interface's state and error counters
handling with the new can-dev can_change_state() mechanism.
Suggested-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Update all of the can interface's state and error counters before
trying any skb allocation that can actually fail with -ENOMEM.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In Intel Quark SoC X1000, both of the Ethernet controllers support
MSI interrupt handling. This patch enables them to use MSI interrupt
servicing in stmmac_pci for Intel Quark X1000.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces run-time board detection through DMI and MAC-PHY
configuration function used by quark_default_data() during initialization. It
fills up the phy_addr for Galileo and Galileo Gen2 boards to indicate that the
Ethernet MAC controller is or is not connected to any PHY.
The implementation takes into consideration for future expansion in Quark
series boards that may have different PHY address that is linked to its MAC
controllers.
This piece of work is derived from Bryan O'Donoghue's initial work for Quark
X1000 enabling.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel Quark SoC X1000 provides two 10/100 Mbps Ethernet MAC
controllers which may or may not be connected to PHY on board.
This MAC controller only supports RMII PHY. This patch add Quark
PCI ID as well as Quark default platform data info to this driver.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently CPTS is built into the netcp driver even though there is no
call out to the CPTS driver. This patch removes the dependency in Kconfig
and remove cpts.o from the Makefile for NetCP.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move firmware version MACRO to a new t4fw_version.h file so that csiostor driver
can also use it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware might change the hca core clock frequency after the driver
issues the INIT_PORT command. Therefore we need to query the new
value again and save in to the cached dev caps.
Fixes: ddd8a6c1 ('net/mlx4_core: Read HCA frequency and map internal clock')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are dumping device capabilities which are supported both by the
firmware and the driver. Align the array that holds the capability
strings with this practice.
Reported-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory corruption at mlx4_MAD_IFC_wrapper.
A table of size dev->caps.pkey_table_len[port]*sizeof(*table)
was allocated, but get_full_pkey_table() assumes that the number
of entries in the table is a multiplication of 32 (which isn't always
correct).
Fixes: 0a9a018 ('mlx4: MAD_IFC paravirtualization')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cmd->autoneg as a user hint to decide what to set in ethtool set settings callback.
When cmd->autoneg == AUTONEG_ENABLE set according to ethtool->advertise otherwise,
set according to ethtool->speed.
Usage:
- ethtool -s eth<x> speed 56000 autoneg off
- ethtool -s eth<x> advertise 0x800000 autoneg on
While we're here:
- Move proto_admin masking outcome check to be adjacent to the operation.
- Move en_warn("port reset..") print to "port reset" block.
Fixes: 312df74 ("net/mlx4_en: mlx4_en_set_settings() always fails when autoneg is set")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_bf_alloc had an unnecessary/duplicate code line. Did no harm,
but not good practice.
Reported by the Mellanox Beijing team.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct mlx4_vhcr was implicitly padded by the gcc compiler on 64-bit
architectures.
This commit makes that padding explicit, to prevent issues with
changing compilers and with incompatibilities between 32-bit architecture
implicit padding and 64-bit architecture implicit padding.
This structure is used in virtualization for communication between
the Host and its Guests. The explicit padding allows 64-bit Hosts
(old and new) to continue to interoperate with 64-bit Guests (old and new).
However, without this fix, 64-bit Hosts could not interoperate with 32-bit
Guests (since these did not insert the padding dword). With this fix,
32-bit Guests will be able to interoperate with 64-bit Hosts (since
the structure offsets will be identical on both).
Reported-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver incorrectly assigned an out-mailbox to this command,
and used an opcode modifier = 0, which is a reserved value (it
should use opcode modifier = 1).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware spec states that the timeout for all commands should be 60 seconds.
In the past, the spec indicated that there were several classes of timeout
(short, medium, and long). The driver has these different timeout classes.
We leave the class differentiation in the driver as-is (to protect against any
future spec changes), but set the timeout for all classes to be 60 seconds.
In addition, we fix a few commands which had hard-coded numeric timeouts specified.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Structs allocated for the resource tracker must be freed in
the error flow.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reserved lKey is different for each VF.
A base lkey value is returned in QUERY_DEV_CAP at offset 0x98.
The reserved L_key value for a VF is:
VF_lkey = base_lkey + (VF_number << 8).
This VF L_key value should be returned in QUERY_FUNC_CAP
(opcode-modifier = 0) at offset 0x48.
To indicate that the lkey value at offset 0x48 is valid, the Hypervisor
sets a flag bit in dword 0x0, offset 27 in the QUERY_FUNC_CAP wrapper
function.
When the VF calls QUERY_FUNC_CAP, it should check if this flag bit is set.
If it is set, the VF should take the reserved lkey value at offset 0x48.
If the bit is not set, the VF should not use a reserved lkey
(i.e., should set its reserved lkey value to 0).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the firmware can detect a bad cable, allow it to generate an
event, and print the problem in the log.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commit is based on a wrong assumption, fdb messages are always sent
into the netns where the interface stands (see vxlan_fdb_notify()).
These fdb messages doesn't embed the rtnl attribute IFLA_LINK_NETNSID, thus we
need to add it (useful to interpret NDA_IFINDEX or NDA_DST for example).
Note also that vxlan_nlmsg_size() was not updated.
Fixes: 193523bf93 ("vxlan: advertise netns of vxlan dev in fdb msg")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix sparse warning about non-static function
drivers/net/bonding/bond_main.c:3737:5: warning: symbol
'bond_3ad_xor_xmit' was not declared. Should it be static?
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a slave is added to a bond and it is not in full duplex mode,
AD_PORT_LACP_ENABLED flag is cleared, due to this LACP PDU is not sent
on slave. When the duplex is changed to full, the flag needs to be set
to send LACP PDU.
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch attempts to fix the following problems when an actor or
partner's aggregator is not active:
1. a slave's lacp port state is marked as AD_STATE_SYNCHRONIZATION
even if it is attached to an inactive aggregator. LACP advertises
this state to the partner, making the partner think he can move
into COLLECTING_DISTRIBUTING state even though this link will not
pass traffic on the local side
2. a slave goes into COLLECTING_DISTRIBUTING state without checking
if the aggregator is actually active
3. when in COLLECTING_DISTRIBUTING state, the partner parameters may
change, e.g. the partner_oper_port_state.SYNCHRONIZATION. The
local mux machine is not reacting to the change and continue to
keep the slave and bond up
4. When bond slave leaves an inactive aggregator and joins an active
aggregator, the actor oper port state need to update to SYNC state.
v2:
* fix style issues in bond_3ad.c
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mode 802.3ad, fix incorrect bond slave active state when slave is not in
active aggregator. During bond_open(), the bonding driver always sets
the slave active flag to true if the bond is not in active-backup, alb,
or tlb modes. Bonding should let the aggregator selection logic set the
active flag when in 802.3ad mode.
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
return type of wait_for_completion_timeout is unsigned long not int, this
patch just fixes up the declarations.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case when alloc_netdev fails we return NULL to a caller. But there is no
check for NULL in the probe drivers. This patch changes NULL to an error
pointer. The function description is amended to reflect what we may get
returned.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After rtl8192cu download firmware routine, set fw_ready flag.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some devices do not support extended scan.
This patch adds support to enble ext_scan selectively.
For SD/PCIe interfaces, deefine ext_scan_support as part of
card structure and use it to initialize ext_scan in adapter
during registering device. For USB interfaces, we initialize
ext_scan during register_dev handler.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SD8801 is Marvell's 1x1 802.11bgn offering.
This patch adds Device IDs for SD8801 and also defines card
structure which has definition for register offsets, buffer sizes etc.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k and ath9k_htc use the variable name "led_blink" to indicate
whether the module parameter "blink" is on. This name is easy to
conflict with other variables, and has caused a compiler error found
by kbuild test bot. The compiler error is as following:
drivers/net/wireless/ath/ath9k/ath9k_htc.o:(.data+0x47c): multiple definition of `led_blink'
drivers/net/wireless/ath/ath9k/ath9k.o:(.bss+0x20): first defined here
Fixes: 3a939a6712 ("ath9k_htc: Add a module parameter to disable blink")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hong Xu <hong@topbug.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Patch "rtlwifi: add support to send beacon frame" allows
the beaconing of rtl8192cu. But mesh beaconing is not
working. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In AP mode, beacon frame is necessary to keep connection.
this patch adds a sending beacon frame routine in initialization routine.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds fix to set carrier state off during ndo_open.
Carrier should be set to ON when device is ready to send data.
In case of station/adhoc interface device is able to transfer
data after successful association/join operation.
For AP this would be after bss_active event.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New wmi-tlv firmware uses HTT 3.0 protocol which
uses TX_FRM command for management frames (instead
of a dedicated command). To support PMF it is
necessary to provide explicit tailroom.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Software encryption was never necessary.
Tested with fw 636 and fw 10.x.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It makes little sense to keep handling irqs if fw
is dead.
This prevents multiple fw register dumps upon
crash on some devices (seen on QCA6174).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only userspace can make an educated decision when
a trigger frame is required so make sure the
autotrigger service is disabled.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 has u-UAPSD
autotrigger service. If it is enabled firmware
generates trigger frames automatically as
configured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The workaround couldn't work correctly because the
802.11 header wasn't properly stripped of QoS Data
bit so it wasn't recognized in the later parts of
tx path as NullFunc frame and ended up in HTT Tx
instead of HTT Mgmt Tx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware supporting beacon templates (i.e. wmi-tlv
for qca6174) doesn't implicitly take dtim period
from the template. Instead it requires vdev param
to be set accordingly.
This fixes dtim period being stuck at 3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT Tx protocol uses arbitrary host assigned ids
too associate with MSDUs when delivering
completions.
Instead of rolling out own id generation scheme
use the tools provided in kernel.
This should have little to no effect on
performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace a magic number with a PCI #define symbol.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Both 10.2 firmware binaries 10.2-00082-4 and
10.2.4.20 have introduced ABI changes to fw_stats
each. This caused fw_stats to output wrong data.
Define new structures and use them to parse the
statistics correctly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will make it easier to implement fw stats
parsing for firmware 10.2.
This also renames a few structures for
consistency.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA6174 in combination with new wmi-tlv firmware is capable of
multi-channel, beamforming, tdls and other features.
This patch just makes it possible to boot these devices and do some basic stuff
like connect to an AP without encryption. Some things may not work or may be
unreliable. New features will be implemented later. This will be addressed
eventually with future patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA6174 chip has an extra 4 bytes in
rx_ppdu_end structure which is used in htt_rx_desc
and HTT Rx ring offset setup. This is necessary
for correct Rx for QCA6174 (otherwise Rx
descriptors are overwritten and corrupted).
This means QCA988X will have an extra 4 byte
padding in Rx descriptor layout which is harmless.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are some very rare cases with some hardware
configuration that the device doesn't init quickly
enough in which case reading chip_id yielded 0.
This caused driver to subsequently fail to setup
the device.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware and firmware (qca6174 hw3.0+ and fw
266+) are capable of full aggregation rx
reordering. If it's enabled then Rx is handled via
a new, separate htt event.
The rx ring behaviour is changed a little to
support the new rx scheme. These changes shouldn't
affect qca988x performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to share the
ath10k_skb_cb with Rx path. The Rx path doesn't
need to keep any mac80211's data.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions may report this event as
part of their diagnostics.
This avoids `unknown event` warnings and adds
tracing for the event.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions may report this event as
part of their diagnostics.
This avoids `unknown event` warnings and adds
tracing for the event.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath10k driver only supports HW crypto (except for management
frames or so - CMAC needs to be done in software). Make it use
the new IEEE80211_HW_SW_CRYPTO_CONTROL flag to ensure mac80211
doesn't erroneously attempt to use software crypto.
Taking through my tree after Kalle's ACK to avoid breaking the
ath10k driver with the next crypto patches.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the commit d75b1ade56 ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. When in busy_poll is we return 0
in napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to see the old value of the LP advertising flags
through ethtool after reconfiguring the PHY and before autonegotiation
completes. If autonegotiation is turned off then the last value seen
will persist indefinitely.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a remote machine crashes while there are pending transmit buffers, the
sunvnet driver reallocates the ring descriptors giving us enries that have
state VIO_DESC_FREE but also an allocated skb. This results in a BUG_ON()
call when the remote reboots and we reach that point in the ring.
This patch:
1) clears pending tx packets in the ring on port reset
2) changes a BUG_ON() to a pr_warn() when a remote host has given us an invalid
descriptor state
3) collapses multiple active buffer frees in a ring to a single message per
ring and adds the device name and remote MAC address
This fixes the particular problem of not cleaning up pending buffers on a
reset, but also prevents us from crashing if the remote handles descriptors
out of order or sets an unexpected state for a descriptor.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the clearing of ring data in vnet_port_free_tx_bufs to after
the freeing of pending buffers in the ring. Otherwise, this can result in
dereferencing a NULL pointer.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the return value of dma_map_single(), rather than calling
virt_to_page() separately
- Check for mapping failue
- Call dma_unmap_single() rather than dma_sync_single_for_cpu()
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_map_single() may fail if an IOMMU or swiotlb is in use, so
we need to check for this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we try to clear EDRRR and EDTRR and immediately continue to
free buffers. This is unsafe because:
- In general, register writes are not serialised with DMA, so we still
have to wait for DMA to complete somehow
- The R8A7790 (R-Car H2) manual states that the TX running flag cannot
be cleared by writing to EDTRR
- The same manual states that clearing the RX running flag only stops
RX DMA at the next packet boundary
I applied this patch to the driver to detect DMA writes to freed
buffers:
> --- a/drivers/net/ethernet/renesas/sh_eth.c
> +++ b/drivers/net/ethernet/renesas/sh_eth.c
> @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev)
> /* Free Rx skb ringbuffer */
> if (mdp->rx_skbuff) {
> for (i = 0; i < mdp->num_rx_ring; i++)
> + memcpy(mdp->rx_skbuff[i]->data,
> + "Hello, world", 12);
> + msleep(100);
> + for (i = 0; i < mdp->num_rx_ring; i++) {
> + WARN_ON(memcmp(mdp->rx_skbuff[i]->data,
> + "Hello, world", 12));
> dev_kfree_skb(mdp->rx_skbuff[i]);
> + }
> }
> kfree(mdp->rx_skbuff);
> mdp->rx_skbuff = NULL;
then ran the loop:
while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine. The
warning fired several times a minute.
To fix these issues:
- Deactivate all TX descriptors rather than writing to EDTRR
- As there seems to be no way of telling when RX DMA is stopped,
perform a soft reset to ensure that both DMA enginess are stopped
- To reduce the possibility of the reset truncating a transmitted
frame, disable egress and wait a reasonable time to reach a
packet boundary before resetting
- Update statistics before resetting
(The 'reasonable time' does not allow for CS/CD in half-duplex
mode, but half-duplex no longer seems reasonable!)
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If RX traffic is overflowing the FIFO or DMA ring, logging every time
this happens just makes things worse. These errors are visible in the
statistics anyway.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of a call to ndo_close() a netdevice driver may call
phy_disconnect() -> phy_detach() -> phy_suspend(), such that the PHY is
suspsended at this point and a netdevice driver may clock gate the
backing peripheral providing MDIO bus accessses as well.
Update mdio_bus_phy_may_suspend() to return whether a PHY is allowed to
be suspended and conversely resumed if and only if it was not previously
suspended before while it is currently in detached (netdev pointer is
NULL) state.
This fixes bus errors seen during S2/S3 suspend/resume cycles for
netdevice drivers such as GENET which clock gates the entire Ethernet
MAC, including the MDIO bus block.
Acked-by: Fugang Duan <B38611@freescale.com>
Tested-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid double calls to phydev->drv->suspend and resume, keep
track of whether the PHY has already been suspended as a consequence of
a successful call to phy_suspend(). We will use this in our MDIO bus
suspend/resume hooks to avoid a double suspend call.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend and phy_resume are an abstraction on top of the PHY device
driver suspend and resume callbacks, utilize those since they are the
proper interface to suspending and resuming a PHY device.
Acked-by: Fugang Duan <B38611@freescale.com>
Tested-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some busy bits are available in the global register 1, such as the ATU
Busy bit. We may want to use this function to wait for them to change,
so add a new parameter to mv88e6352_wait() instead of hard-coding
REG_GLOBAL2.
In the meantime, since the REG_READ() macro already checks for error,
remove the redundant check for ret < 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds debug messages for the generic mv88e6xxx read and write
routines. The output is similar to this:
mdio-gpio mdio-gpio.0: <- addr: 0x1b reg: 0x05 val: 0x4000
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x07 val: 0x3113
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x08 val: 0x0330
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x09 val: 0x0000
This is convenient to dynamically debug operations through debugfs with:
echo file mv88e6xxx.c +p > <debugfs>/dynamic_debug/control
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While being in an ERROR_WARNING state, and receiving further
bus error events with error counters still in the ERROR_WARNING
range of 97-127 inclusive, the state handling code erroneously
reverts back to ERROR_ACTIVE.
Per the CAN standard, only revert to ERROR_ACTIVE when the
error counters are less than 96.
Moreover, in certain Kvaser models, the BUS_ERROR flag is
always set along with undefined bits in the M16C status
register. Thus use bitwise operators instead of full equality
for checking that register against bus errors.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On some x86 laptops, plugging a Kvaser device again after an
unplug makes the firmware always ignore the very first command.
For such a case, provide some room for retries instead of
completely exiting the driver init code.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Send expected argument to the URB completion hander: a CAN
netdevice instead of the network interface private context
`kvaser_usb_net_priv'.
This was discovered by having some garbage in the kernel
log in place of the netdevice names: can0 and can1.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upon receiving a hardware event with the BUS_RESET flag set,
the driver kills all of its anchored URBs and resets all of
its transmit URB contexts.
Unfortunately it does so under the context of URB completion
handler `kvaser_usb_read_bulk_callback()', which is often
called in an atomic context.
While the device is flooded with many received error packets,
usb_kill_urb() typically sleeps/reschedules till the transfer
request of each killed URB in question completes, leading to
the sleep in atomic bug. [3]
In v2 submission of the original driver patch [1], it was
stated that the URBs kill and tx contexts reset was needed
since we don't receive any tx acknowledgments later and thus
such resources will be locked down forever. Fortunately this
is no longer needed since an earlier bugfix in this patch
series is now applied: all tx URB contexts are reset upon CAN
channel close. [2]
Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF
event, which is the recommended handling method advised by
the device manufacturer.
[1] http://article.gmane.org/gmane.linux.network/239442http://www.webcitation.org/6Vr2yagAQ
[2] can: kvaser_usb: Reset all URB tx contexts upon channel close
889b77f7fd
[3] Stacktrace:
<IRQ> [<ffffffff8158de87>] dump_stack+0x45/0x57
[<ffffffff8158b60c>] __schedule_bug+0x41/0x4f
[<ffffffff815904b1>] __schedule+0x5f1/0x700
[<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10
[<ffffffff81590684>] schedule+0x24/0x70
[<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0
[<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110
[<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80
[<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb]
[<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb]
[<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20
[<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb]
[<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0
[<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110
[<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd]
[<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20
[<ffffffff81069f65>] ? local_clock+0x15/0x30
[<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd]
[<ffffffff814fbb31>] ? process_backlog+0xb1/0x130
[<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd]
[<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30
[<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120
[<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60
[<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110
[<ffffffff81004dfd>] handle_irq+0x1d/0x30
[<ffffffff81004727>] do_IRQ+0x57/0x100
[<ffffffff8159482a>] common_interrupt+0x6a/0x6a
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix compilation warning:
drivers/net/ethernet/cadence/macb.c:2415:12: warning: 'macb_suspend'
defined but not used [-Wunused-function]
static int macb_suspend(struct device *dev)
drivers/net/ethernet/cadence/macb.c:2432:12: warning: 'macb_resume'
defined but not used [-Wunused-function]
static int macb_resume(struct device *dev)
when CONFIG_PM=y, CONFIG_PM_SLEEP=n are used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is trying to acquire clocks which maybe
are not available yet. Allow the driver to request
deffered probe by providing a probe function and
registering it with module_platform_driver. [1]
This patch is based on 3.19-rc5.
[1] https://lkml.org/lkml/2013/9/23/118
Signed-off-by: Nicolae Rosia <nicolae.rosia@certsign.ro>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 69ad0dd7af
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Mon May 19 13:59:59 2014 -0300
net: mv643xx_eth: Use dma_map_single() to map the skb fragments
caused a nasty regression by removing the support for highmem skb
fragments. By using page_address() to get the address of a fragment's
page, we are assuming a lowmem page. However, such assumption is incorrect,
as fragments can be in highmem pages, resulting in very nasty issues.
This commit fixes this by using the skb_frag_dma_map() helper,
which takes care of mapping the skb fragment properly. Additionally,
the type of mapping is now tracked, so it can be unmapped using
dma_unmap_page or dma_unmap_single when appropriate.
This commit also fixes the error path in txq_init() to release the
resources properly.
Fixes: 69ad0dd7af ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments")
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq(). This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it. Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.
I could easily trigger a crash by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine.
To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
handlers before clearing EESIPR in sh_eth_close() and
sh_eth_set_ringparam()
After this, I could run the loop for 100,000 iterations successfully.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.
I could easily trigger this by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding. This could result in leaking sensitive
data. We also pass different lengths to dma_map_single() and
dma_unmap_single().
Use skb_padto() to pad properly, before calling dma_map_single().
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
pull-request: wireless-drivers-next 2015-01-22
now a bigger pull request for net-next. Rafal found a UTF-8 bug in
patchwork[1] and because of that two commits (d0c102f70a and
d0f66df539) have his name corrupted:
Acked-by: Rafa? Mi?ecki <zajec5@gmail.com>
Somehow I failed to spot that when I commited the patches. As rebasing
public git trees is bad, I thought we can live with these and decided
not to rebase. But I'll pay close attention to this in the future to
make sure that it won't happen again. Also we requested an update to
patchwork.kernel.org, the latest patchwork doesn't seem to have this
bug.
Also please note this pull request also adds one DT binding doc, but
this was reviewed in the device tree list:
.../bindings/net/wireless/qcom,ath10k.txt | 30 +
Please let me know if you have any issues.
[1] https://lists.ozlabs.org/pipermail/patchwork/2015-January/001261.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.
Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.
Fixes: d9ba8f9e62 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear the TX COE bit when force_thresh_dma_mode is set even hardware
dma capability says support.
Tested on BF609.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont' pass SF_DMA_MODE to rxmode in this case.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yXcf
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.20-20150121' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-21-01
this is a pull request of 4 patches for net-next/master.
Andri Yngvason contributes one patch to further consolidate the CAN
state change handling. The next patch is by kbuild test robot/Fengguang
Wu which fixes a coccinelle warning in the CAN infrastructure. The two
last patches are by me, they remove a unused variable from the flexcan
and at91_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sujith Manoharan