We're planning to remove the gpiochip_add() function to swith
to gpiochip_add_data() with NULL for data argument.
Cc: linux-mips@linux-mips.org
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11921/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mtd_to_nand() was recently introduced to avoid direct accesses to the
mtd->priv field. Update all MIPS specific implementations to use this
helper.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate alchemy driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We weren't doing anything in the ->set_mode() callback. So, this patch
doesn't provide any set-state callbacks.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linaro-kernel@lists.linaro.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/10599/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
bcsr_csc_handler() is a cascading interrupt handler. It has a
disable_irq_nosync()/enable_irq() pair around the generic_handle_irq()
call. The value of this disable/enable is zero because its a complete
noop:
disable_irq_nosync() merily increments the disable count without
actually masking the interrupt. enable_irq() soleley decrements the
disable count without touching the interrupt chip. The interrupt
cannot arrive again because the complete call chain runs with
interrupts disabled.
Remove it.
[ralf@linux-mips.org: Fold in followup fix from Thomas Gleixner.]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10702/
Patchwork: https://patchwork.linux-mips.org/patch/10708/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hand in irq_data and avoid the redundant lookup of irq_desc.
Originally-from: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* cleanup-clk-h-includes: (62 commits)
clk: Remove clk.h from clk-provider.h
clk: h8300: Remove clk.h and clkdev.h includes
clk: at91: Include clk.h and slab.h
clk: ti: Switch clk-provider.h include to clk.h
clk: pistachio: Include clk.h
clk: ingenic: Include clk.h
clk: si570: Include clk.h
clk: moxart: Include clk.h
clk: cdce925: Include clk.h
clk: Include clk.h in clk.c
clk: zynq: Include clk.h
clk: ti: Include clk.h
clk: sunxi: Include clk.h and remove unused clkdev.h includes
clk: st: Include clk.h
clk: qcom: Include clk.h
clk: highbank: Include clk.h
clk: bcm: Include clk.h
clk: versatile: Remove clk.h and clkdev.h includes
clk: ux500: Remove clk.h and clkdev.h includes
clk: tegra: Properly include clk.h
...
Some determine_rate implementations are not returning an error
when they failed to adapt the rate according to the rate request.
Fix them so that they return an error instead of silently
returning 0.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: "Emilio López" <emilio@elopez.com.ar>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Tero Kristo <t-kristo@ti.com>
CC: Peter De Schrijver <pdeschrijver@nvidia.com>
CC: Prashant Gaikwad <pgaikwad@nvidia.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-doc@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-omap@vger.kernel.org
CC: linux-mips@linux-mips.org
CC: linux-tegra@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock rates are stored in an unsigned long field, but ->determine_rate()
(which returns a rounded rate from a requested one) returns a long
value (errors are reported using negative error codes), which can lead
to long overflow if the clock rate exceed 2Ghz.
Change ->determine_rate() prototype to return 0 or an error code, and pass
a pointer to a clk_rate_request structure containing the expected target
rate and the rate constraints imposed by clk users.
The clk_rate_request structure might be extended in the future to contain
other kind of constraints like the rounding policy, the maximum clock
inaccuracy or other things that are not yet supported by the CCF
(power consumption constraints ?).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: "Emilio López" <emilio@elopez.com.ar>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
CC: Peter De Schrijver <pdeschrijver@nvidia.com>
CC: Prashant Gaikwad <pgaikwad@nvidia.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-doc@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-omap@vger.kernel.org
CC: linux-mips@linux-mips.org
CC: linux-tegra@vger.kernel.org
[sboyd@codeaurora.org: Fix parent dereference problem in
__clk_determine_rate()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[sboyd@codeaurora.org: Folded in fix from Heiko for fixed-rate
clocks without parents or a rate determining op]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock provider uses the consumer API, so include clk.h
explicitly.
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
The current code uses bits 0-6 of the sys_cpupll register to calculate
core clock speed. However this is only valid on Au1300, on all earlier
models the hardware only uses bits 0-5 to generate core clock.
This fixes clock calculation on the MTX1 (Au1500), where bit 6 of cpupll
is set as well, which ultimately lead the code to calculate a bogus cpu
core clock and also uart base clock down the line.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Reported-by: John Crispin <blogic@openwrt.org>
Tested-by: Bruno Randolf <br1@einfach.org>
Cc: stable@vger.kernel.org [v3.17+]
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9279/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
set_cpuspec() has been dropped with commit 074cf65670
("MIPS: Alchemy: remove cpu_table.") in late 2008.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9150/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This was lost during the rewrite of clock framework support.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9149/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Au1000 and Au1500 calculate the LRCLK a bit differently than
newer models: a single bit in MEM_STCFG0 selects if pclk is divided
by 4 or 5.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9148/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They were added to this function by mistake when they were added to the
clk_ops.determine_rate callback.
Fixes: 1c8e600440 ("clk: Add rate constraints to clocks")
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Adds a way for clock consumers to set maximum and minimum rates. This
can be used for thermal drivers to set minimum rates, or by misc.
drivers to set maximum rates to assure a minimum performance level.
Changes the signature of the determine_rate callback by adding the
parameters min_rate and max_rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[sboyd@codeaurora.org: set req_rate in __clk_init]
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: min/max rate for sun6i_ahb1_clk_determine_rate
migrated clk-private.h changes to clk.c]
much later than usual due to several last minute bugs that had to be
addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future which
will better parition clock providers from clock consumers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jD84
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
This is in preparation for clock providers to not have to deal with struct clk.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Replacing it with a call to __clk_is_prepared(), which isn't entirely
equivalent but in practice shouldn't matter.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8120/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add an explicit call to set the desired rate to get the correct
clock routing for the PSC clocks. It wasn't broken before, but
now it's less affected by bootloader changes.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7554/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On boards which don't support poweroff, systemd complains about this fact.
In case poweroff fails, just sit and spin in the wait loop.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7558/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the clock framework in place, remove unused functions and bits,
and drop the CLK_IGNORE_UNUSED flag, which is now unneeded.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7473/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the clock framework to en/disable the clock to the au1100
framebuffer device.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7474/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the clk framework to set up and enable all PSC clocks.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7469/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add use of the common clock framework to set and enable the 48MHz
clock source for the onchip OHCI and UDC blocks.
Tested on a DB1500. (Au1200 and Au1300 use an external 48MHz crystal).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7467/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the clock framework to get the rate of the peripheral clock.
Remove the now obsolete get_uart_baud_base function.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7468/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces common clock framework integration for all
configurable on-chip clocks on Alchemy chips:
- 2 or 3 PLLs which generate integer multiples of the root rate 12MHz,
- 6 dividers which take one of the 3 PLLs as input and divide their
rate by either multiples of 2 or 1 (Au1300).
- another bank of up to 6 muxes which take either one of the 6
above dividers or one of the PLLs directly and divide their rate
further by 1, 2, 3 or 4.
- a few other sources which are used by onchip peripherals and are
informational.
This implementation will take the clock tree as it was set up
by boot firmware: all in-kernel boards should continue to work
without having to set up the clock tree in board code.
CLK_IGNORE_DISABLED will be removed once all drivers have been
converted.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7466/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes the static memory controller registers to offsets
from base, prefixes them with AU1000_ to avoid silent failures due to
changed addresses and introduces helpers to access them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7463/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes all absolute SYS_XY registers to offsets from the
SYS block base, prefixes them with AU1000 to avoid silent failures due
to changed addresses, and introduces helper functions to read/write
them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7464/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_DMA_COHERENT is no longer set; default to noncoherent io on
Au1200 revision AB to make USB work.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6745/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With binutils 2.24 the attempt to switch with microMIPS mode to MIPS III
mode through .set mips3 results in *lots* of warnings like
{standard input}: Assembler messages:
{standard input}:397: Warning: the 64-bit MIPS architecture does not support the `smartmips' extension
during a kernel build. Fixed by using .set arch=r4000 instead.
This breaks support for building the kernel with binutils 2.13 which
was supported for 32 bit kernels only anyway and 2.14 which was a bad
vintage for MIPS anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The au1xxx-ide driver isn't any faster than pata_platform since it
spends a lot of time busy waiting for DMA to finish; faster PIO/DMA
modes only work on the db1200 with a certain cpu speed, UDMA is broken,
and finally the old IDE layer is on death row, so time to switch to
the newer ATA layer.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6662/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge the db1200.h and db1300.h headers into their only users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6660/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch merges support for all DB1xxx and PB1xxx
boards into a single image, along with a new single defconfig
for them.
Run-tested on DB1300 and DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6577/
Patchwork: https://patchwork.linux-mips.org/patch/6659/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Alchemy chips have coherent DMA, but for example the USB or AC97
peripherals on the Au1000/1500/1100 are not.
This patch uses DMA_MAYBE_COHERENT on Alchemy and sets coherentio based
on CPU type.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6576/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
enabled __must_check logic triggers a build error for mtx1 and gpr
in the prom init code. Fix by checking the kstrtoul() return value.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6574/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With CONFIG_GPIOLIB=y gpios need to be requested before they can be
modified. Request the SD carddetect pins, and drop the SPI direction
setup, as the driver does that for us anyway. This gets rid of a
lot of WARN_ON()s triggered by GPIO core, and restores functionality
of the touschreen controller.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6497/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6320/
Panic() is going to add a \n itself and it's annoying if a panic message rolls
of the screen on a device with no scrollback.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5934/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace hardcoded CP0 PRId and CP1 FPIR register access masks throughout.
The change does not touch places that use shifted or partial masks.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Kconfig symbol MIPS_DISABLE_OBSOLETE_IDE was added in v2.6.10. It
has never been used. Let's remove it.
The symbol was originally introduced by the following commit
commit 2bfa662b64a7ee593f3039c1d3fd81a7766a63cd
Author: Pete Popov <ppopov@embeddedalley.com>
Date: Tue Oct 12 06:24:19 2004 +0000
- Db1550 bug fixes
- updated defconfig
- updated Kconfig to use DMA_COHERENT since new silicon is coherent
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Patchwork: http://patchwork.linux-mips.org/patch/5064/
Acked-by: John Crispin <blogic@openwrt.org>
The support for PB1100, PB1500, and PB1550 got merged into the code for
DB1000 and DB1550 code in v3.7. When that was done the three related
Kconfig symbols were dropped. But not all related Kconfig macros were
removed. Do so now.
Note that the PB1100 code in the Au1100 LCD driver is removed entirely
and not converted to use its current Kconfig macro. That is done because
the macros it uses (PB1100_G_CONTROL, PB1100_G_CONTROL_BL, and
PB1100_G_CONTROL_VDD) are never defined. Actually only one of these was
ever defined (PB1100_G_CONTROL) but that define was removed in v2.6.34.
So, as far as I can tell, this code could have never compiled.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Patchwork: http://patchwork.linux-mips.org/patch/5040/
Acked-by: John Crispin <blogic@openwrt.org>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that the r4k timer is registered no matter what, bump the rating of
the Alchemy 32kHz timer so that it gets used when it is working,
and fall back on the r4k when it isn't.
This fixes a timer-related hang on platform with a working 32kHz timer
(the better rated c0 timer stops while executing 'wait' leading to (almost)
eternal sleep) and an oops on boot on platforms without a working 32kHz
timer (due to double registration of the r4k timer).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/4728/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A previous patch converted the Alchemy platform to use the OHCI and EHCI
platform drivers. As a result, all the common logic to handle USB present in
drivers/usb/host/alchemy-common.c has no reason to remain here, so we move it
to arch/mips/alchemy/common/usb.c which is a more appropriate place. This
change was suggested by Manuel Lauss.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the Alchemy platform to register the ohci-platform driver, now that
the ohci-platform driver properly handles the specific ohci-au1xxx resume
from suspend case.
This also greatly simplifies the power_{on,off} callbacks and make them
work on platform device id instead of checking the OHCI controller base
address like what was done in ohci-au1xxx.c.
Impacted defconfigs are also updated accordingly to select the OHCI platform
driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the ehci platform driver power_{on,suspend,off} callbacks to perform the
USB block gate enabling/disabling as what the ehci-au1xxx.c driver does.
Update the db1200 and db1300 defconfigs to now select the EHCI platform
driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PB1100/1500 are similar to their DB-cousins but with a few
more devices on the bus.
This patch adds PB1100/1500 support to the existing DB1100/1500
code.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: lnux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1550 is more or less a DB1550 without the PCI IDE controller,
a more complicated (read: configurable) Flash setup and some other
minor changes. Like the DB1550 it can be automatically detected by
reading the CPLD ID register bits.
This patch adds PB1550 detection and setup to the DB1550 code.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Combine support for the DB1200/PB1200, DB1300 and DB1550 boards into
a single kernel image.
defconfig-generated image verified on DB1200, DB1300 and DB1550.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4335/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Without this udelay(1) PCI idsel does not work correctly on the
"singleboard" (T-Mobile Surfbox) for the MiniPCI device. The result is
that PCI configuration fails and the MiniPCI card is not detected
correctly. Instead of
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:03.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40011000-0x40011fff]
We see only the CardBus device:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x40000fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40001000-0x40001fff]
Later the device driver shows this error:
ath5k 0000:00:03.0: cannot remap PCI memory region
ath5k: probe of 0000:00:03.0 failed with error -5
I assume that the logic chip which usually supresses the signal to the CardBus
card has some settling time and without the delay it would still let the
Cardbus interfere with the response from the MiniPCI card.
What I cannot explain is why this behaviour shows up now and not in earlier
kernel versions before. Maybe older PCI code was slower?
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: linux-mips@linux-mips.org
Cc: manuel.lauss@googlemail.com
Cc: florian@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/4087/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the loop in the cascade handler and instead unconditionally
handle just the first set interrupt coming from the CPLD.
This gets rid of a lot of spurious interrupts being triggered for
the SMSC91111 ethernet chip especially under high(er) IDE load:
"eth0: spurious interrupt (mask = 0xb3)"
Verified on DB1200 and DB1300.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3288/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
YAMON on all devboards provides the "memsize" envvar; in the unlikely
case that it can't be parsed just assume 64MB, which all boards have
at least.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3286/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
These will show up as a build failure once we clean up a
misuse of module.h in the mips termios header.
Uses export.h: (EXPORT_SYMBOL)
arch/mips/cavium-octeon/setup.c
arch/mips/pmc-sierra/yosemite/setup.c
arch/mips/rb532/devices.c
arch/mips/sni/setup.c
Uses module.h: (symbol_get/put)
arch/mips/alchemy/devboards/db1200.c
Uses module.h: (print_modules)
arch/mips/kernel/traps.c
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3448/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the default partition parser, cmdlinepart, provided by the plat_nand driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since a clocksource change post 3.2-rc1, tasks on my DB1500 board
hang after random amounts of time (from a few minutes to a few hours),
regardless of load. Debugging showed that the compare-match register
value is a few seconds lower than the current counter value.
The minimum value of 8 was initialy determined by a trial-and-error
approach. Currently it is sufficient for all Alchemys (without PCI
apparently), independent of CPU clock; only the DB1500 and DB1550
boards experience these timer-related tasks hangs now.
This patch increases the minimum timeout by 1 (to 9 counter ticks)
which seems sufficient since the systems are still working perfectly
fine after over 24 hours.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3214/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1200 has the CPLD located at an address which on the DB1200 is
RAM; reading the Board-ID sometimes results in a PB1200 being detected
instead (especially during reboots after long uptimes).
On the other hand, the address of the DB1200's CPLD is hosting Flash
chips on the PB1200. Test for the DB1200 first and additionally do a
quick write-test to the hexleds register to make sure we're writing
to the CPLD.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3005/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With a generic plat_irq_dispatch (for Alchemy at least) code for both
interrupt controller types can coexist in a single kernel image and be
autodetected at runtime.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2935/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add necessary transceiver control platform data and hook up the
IrDA peripheral on the DB1000 and DB1100 boards.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2878/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled and we even check
and yell when an interrupt handler returns with interrupts enabled (see
commit [b738a50a: genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
[ralf@linux-mips.org: Fixed up conflicts in
arch/mips/alchemy/common/dbdma.c, arch/mips/cavium-octeon/smp.c and
arch/mips/kernel/perf_event.c.]
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.delinux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Devboards can use the 32kHz counter as a RTC device.
Also delete the custom CMOS RTC header, which can be used for the
DS1693 on the PB1500. But since it doesn't have a buffer battery
it is as useful as the on-chip RTC which I prefer.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These 3 boards are very similar; with this patch a single kernel image
which runs on all three can be built.
Tested on DB1500 and DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1200 is basically a DB1200 with additional MMC and camera sockets
and different base addresses for external hardware (CPLD, IDE, Net, NAND).
This patch implements the missing PB1200 features in DB1200 support code
and runtime board detection.
Tested on DB1200 only.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2880/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of these files are have more comments than real code; merge
them all into single board-<name>.c files.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2869/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Initially I had to write to both the MASK and ENABLE registers, otherwise
the CPLD would generate tons of spurious interrupts. With the change to
the demux handler to disable the muxed line, it is now sufficient to
disable the interrupt by writing either the enable or mask register.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No test hardware and no (apparent) users. These boards seem very
similar to the DB1500, so if required support can be brought back
again (I have datasheets) but then with dedicated board code, not
tacked on to DB1000 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2864/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Walleij