Mark the OMAP3-specific DPLL functions as being OMAP3-specific by moving
them from mach-omap2/dpll.c to mach-omap2/dpll3xxx.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Some HW blocks have errata which requires specific slave idle mode
under certain conditions.
This patch adds an hwmod API to allow setting slave idlemode
ensuring that any SYSCONFIG register updates go through hwmod.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
First, this patch adds new worst-case latency values to the
omap_device_pm_latency struct. Here the worst-case measured latencies
for the activate and deactivate hooks are stored.
In addition, add an option to auto-adjust the latency values used for
device activate/deactivate.
By setting a new 'OMAP_DEVICE_LATENCY_AUTO_ADJUST' flag in the
omap_device_pm_latency struct, the omap_device layer automatically
adjusts the activate/deactivate latencies to the worst-case measured
values.
Anytime a new worst-case value is found, it is printed to the console.
Here is an example log during boot using UART2 s an example. After
boot, the OPP is manually changed to the 125MHz OPP:
[...]
Freeing init memory: 128K
omap_device: serial8250.2: new worst case deactivate latency 0: 30517
omap_device: serial8250.2: new worst case activate latency 0: 30517
omap_device: serial8250.2: new worst case activate latency 0: 218139648
omap_device: serial8250.2: new worst case deactivate latency 0: 61035
omap_device: serial8250.2: new worst case activate latency 0: 278076171
omap_device: serial8250.2: new worst case activate latency 0: 298614501
omap_device: serial8250.2: new worst case activate latency 0: 327331542
/ # echo 125000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_setspeed
omap_device: serial8250.2: new worst case deactivate latency 0: 91552
Motivation: this can be used as a technique to automatically determine
the worst case latency values. The current method of printing a
warning on every violation is too noisy to actually interact the
console in order to set low OPP to discover latencies.
Another motivation for this patch is that the activate/deactivate
latenices can vary depending on the idlemode of the device. While
working on the UARTs, I noticed that when using no-idle, the activate
latencies were as high as several hundred msecs as shown above. When
the UARTs are in smart-idle, the max latency is well under 100 usecs.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch only affects documentation; no functional changes are
included.
Clean up comments in the current clockdomain, powerdomain code and
header files. This mostly involves conversion to kerneldoc format,
although some clarifications are also included.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Nothing calls pwrdm_clk_state_switch(), and the function that seems to be
its ideal use case calls pwrdm_clkdm_state_switch(clk->clkdm), so remove it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
This patch rearranges the order of structure members in struct powerdomain
to avoid wasting memory due to alignment restrictions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add usecounting for wakeup and sleep dependencies. In the current
situation, if several functions add dependencies on the same
clockdomains, when the first dependency removal function is called,
the dependency will be incorrectly removed from the hardware.
Add clkdm_clear_all_wkdeps() and clkdm_clear_all_sleepdeps(), which
provide a fast and usecounting-consistent way to clear all hardware
clockdomain dependencies, since accesses to these registers can be
quite slow. pm{2,3}4xx.c has been updated to use these new functions.
The original version of this patch did not touch these files, which
previously wrote directly to the wkdep registers, and thus confused
the usecounting code. This problem was found by Kevin Hilman
<khilman@deeprootsystems.com>.
N.B.: This patch introduces one significant functional difference over
the previous pm34xx.c code: sleepdeps are now cleared during
clockdomain initialization, whereas previously they were left
untouched. This has been tested by Kevin and confirmed to work.
The original version of this patch also did not take into
consideration that some clockdomains do not have sleep or wakeup
dependency sources, which caused NULL pointer dereferences. This
problem was debugged and fixed by Kevin Hilman
<khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
OMAP clockdomains and powerdomains are currently defined statically,
only registered at boot, and never unregistered, so we can remove the
unregister function and the locking. A variant of this was originally
suggested a while ago by Dmitry Baryshkov <dbaryshkov@gmail.com>.
This version of this patch contains an additional fix from Kevin Hilman
<khilman@deeprootsystems.com> to address one of the pwrdm_for_each_nolock()
users in mach-omap2/pm-debug.c. Thanks Kevin.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
For some reason, previously, we included the MDM clockdomain on all 24xx,
but the stacked die-on-die modem configuration (chassis mode) is only
available on OMAP2430.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Previously some of the clockdomain wakeup/sleep dependency structures
were shared between several domains. For the subsequent wakeup and sleep
dependency usecounting patch to work, these can no longer be
shared. This patch splits the shared structures apart.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move clockdomain wakeup dependency and sleep dependency data
structures from the powerdomain layer to the clockdomain layer, where
they belong. These dependencies were originally placed in the
powerdomain layer due to unclear documentation; however, it is clear
now that these dependencies are between clockdomains. For OMAP2/3,
this is not such a big problem, but for OMAP4 this needs to be fixed.
Thanks to Benoît Cousson <b-cousson@ti.com> for his advice on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
One of the clock domains was missing from the auto-generated file.
It has been added here.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clockdomain related code being in place, it is not necessary to have
some part of the clock code commented out. This would help the validation of
the clockdomain functions using the clock level interfaces.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The armwdt_ck clock uses a fixed divisor, so it can use the OMAP clock
fixed divisor recalculation code, rather than a custom function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
One of the OMAP1 clocks can use the fixed divisor recalculation code
introduced in the OMAP2 clock code, so rename the
omap2_fixed_divisor_recalc() function to omap_fixed_divisor_recalc()
and make it available to all OMAPs. A followup patch converts the OMAP1
clock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM3505/17 though a OMAP3530 derivative have the following
main differences
- Removal of the following OMAP3 modules
- IVA
- ISP/CAM
- Modem and D2D components (MAD2D, SAD2D)
- USIM
- SSI
- Mailboxes
- USB OTG
- ICR
- MSPRO
- SmartReflex
- SDRC replaced with EMIF4 Controller in the SDRC subsystem
thus adding support for DDR2 memory devices
- Addition of the following new modules
- Ethernet MAC (CPGMAC)
- CAN Controller (HECC)
- New USB OTG Controller with integrated Phy
- Video Processing Front End (VPFE)
- Additional UART (UART4)
- All security accelerators disabled on GP devices and not to
be accessed or configured
This patch defines CPU flags for AM3505/17 and update the clock table.
Clock support for new modules will be added by subsequent patches.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
[paul@pwsan.com: updated for 2.6.34 clock layout]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add CK_* flags for the two new Sitara chips, AM3505 and AM3517, and
the OMAP34xx die shrink, OMAP36xx/OMAP37xx. Introduce a new CK_*
flag, CK_3XXX, that marks all clocks that are common to OMAP3 family
chips. CK_343X now refers to clocks that are available only on
OMAP34{1,2,3,4}0 (WTBU) and OMAP35{03,15,25,30} (any version).
At some point, the RATE_IN_* flags should be updated also.
While here, add some documentation describing the chip families
covered by these clock flags.
This patch is partially based on patches from Ranjith Lohithakshan
<ranjithl@ti.com> and Vishwanath Sripathy <vishwanath.bs@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Cc: Vishwanath Sripathy <vishwanath.bs@ti.com>
AM3517/05 has a few additional control module registers defined mainly
to control the new IP's. This patch adds support for those new registers.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Port the APIs to support the OMAP4 clockdomain framework.
Also take care of the compiling requirements for the same.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The introduction of the OMAP4 Clock Domain framework requires
some adaptaions to be done in the earlier files to place the
common and uncommon data in the proper places where they belong.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The Autogenerated OMAP4 clock domain specific file
(mach-omap2/clockdomains44xx.h) is added here. This file is
auto-generated using python scripting, and following is the lsit of
the people involved:
Benoit Cousson
Abhijit Pagare
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Here the APIs are modified to use absolute addresses instead of module offsets.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Here the ".clkstctrl_reg" field is added to the clockdomain stucture
as the module offsets for OMAP4 do not map one to one for powerdomains
and clockdomains as it used to for OMAP3. Hence we need to use absolute
addresses to access the control registers. Some of the clock domains have
modules falling in the address space of PRM partition. Hence necessitating
the use of absolute adresses.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The proper Macros have to be used for platform specific calls and
some of the compiling requirements and init calls are taken care of.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Taking care of the platform specific and common power domains with
proper checks. Also refining some Macros according to the latest
OMAP4 requirements.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The Autogenerated OMAP4 power domain specific file (mach-omap2/powerdomains44xx.h)
is added here.
This file is auto-generated using python scripting and following is the list of the people
involved:
Paul Walmsley
Benoit Cousson
Abhijit Pagare
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Module offsets were same for OMAP2 and OMAP3 while they differ for OMAP4.
Hence we need different macros for identifying platform specific offsets.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Some of the OMAP4 specific chip level initialisations are taken care of.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: updated to use '4430ES1' rather than simply '4430'; updated
to apply after the intervening cpu.h/id.c patch; thanks also to Tony
for catching a bug in my rewrite]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This makes the FEC clock configuration consistent with the UART one.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The gpt_clk rate function doesn't consider the PER divider. This causes a
significant drift in time accounting. Fix this by introducing the correct rate
calculation function.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch disables all unnecessary clock in mx25_clocks_init() to make a clean
start, the same as is being done for the rest of the i.MX chips.
This patch was tested on i.MX25 PDK.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The fref is needless on mx25 since the reference clock is fixed at 24MHz.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (25 commits)
OMAP2/3: DMTIMER: Clear pending interrupts when stopping a timer
PM debug: Fix warning when no CONFIG_DEBUG_FS
OMAP3: PM: DSS PM_WKEN to refill DMA
OMAP: timekeeping: time should not stop during suspend
OMAP3: PM: Force write last pad config register into save area
OMAP: omap3_pm_get_suspend_state() error ignored in pwrdm_suspend_get()
OMAP3: PM: Enable wake-up from McBSP2, 3 and 4 modules
OMAP3: PM debug: fix build error when !CONFIG_DEBUG_FS
OMAP3: PM: Removing redundant and potentially dangerous PRCM configration
OMAP3: Fixed ARM aux ctrl register save/restore
OMAP3: CPUidle: Fixed timer resolution
OMAP3: PM: Remove duplicate code blocks
OMAP3: PM: Disable interrupt controller AUTOIDLE before WFI
OMAP3: PM: Enable system control module autoidle
OMAP3: PM: Ack pending interrupts before entering suspend
omap: Enable GPMC clock in gpmc_init
OMAP1 clock: fix for "BUG: spinlock lockup on CPU#0"
OMAP4: clocks: Fix the clksel_rate struct DPLL divs
OMAP4: PRCM: Fix the base address for CHIRONSS reg defines
OMAP: dma_chan[lch_head].flag & OMAP_DMA_ACTIVE tested twice in omap_dma_unlink_lch()
...
This patch fixes power LED blinking and power-off on DNS-323 rev. B1.
GPIO pin 3 has to be set to 1 to stop power LED blinking and to allow the LED to be controlled via leds-gpio. This pin has to be also set to 1 for power-off to work.
To power-off the rev. B1 machine, pin 8 has to be set to 1 and then set to 0 to do actual power-off.
Tested on my DNS-323 rev. B1
Signed-off-by: Erik Benada <erikbenada@yahoo.ca>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
OMAP GP timers keep running for a few cycles after they are stopped,
which can cause the timer to expire and generate an interrupt. The
pending interrupt will prevent e.g. OMAP from entering suspend, thus
we ack it manually. Only applicable on OMAP2/3/4.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit cfc38999f (backlight: Pass device through notify callback)
added a struct device argument to the notify callback, but didn't
update the user of it in mach-hmt.c
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments
ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work
ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot()
ARM: 5884/1: arm: Fix DCC console for v7
ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels"
ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void)
ARM: fix badly placed mach/plat entries in Kconfig & Makefile
To distinguish between mx31lite and mx31lilly boards better to use
different enum types.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix following warning when CONFIG_DEBUG_FS wasn't selected:
arch/arm/mach-omap2/pm-debug.c:57: warning: 'pm_dbg_init' declared 'static' but never defined
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, DSS does not wakeup when there is a DMA request. DSS wake
up event must be enabled so that the DMA request to refill the FIFO
will wake up the CORE domain.
Signed-off-by: Subramani Venkatesh <subramani.venkatesh@windriver.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
During suspend, the kernel timekeeping subsystem is shut down. Before
suspend and upon resume, it uses a weak function
read_persistent_clock() to determine the amount of time that elapsed
during suspend.
This function was not implemented on OMAP, so from the timekeeping
subsystem perspective (and thus userspace as well) it appeared that no
time elapsed during suspend.
This patch uses the 32k sync timer as a the persistent clock.
NOTE: This does *NOT* fully handle wrapping of the 32k sync timer, so
more than one wrapping of the 32k sync timer during suspend may
cause problems. Also note there are not interrupts when the 32k
sync timer wraps, so something else has to be done.
Reported-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register
(ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous
OCP access to the SCM register area. Fixed by writing the last
register to the save area.
Also, optimized the delay loop for the HW save to include an udelay(1),
which limits the number of unnecessary HW accesses to SCM register area
during the save.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
val is an u64 pointer, we need an int to check the error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Wake-up from McBSP ports are needed, especially when the THRESHOLD
dma mode is in use for audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The PM debug code fails to build on when CONFIG_DEBUG_FS is not
enabled.
Build error log:
arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/built-in.o: In function `configure_vc':
arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init'
arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init'
make: *** [.tmp_vmlinux1] Error 1
This patch fixes the above errors.
Kernel booting is tested on omap zoom2 and zoom3 boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
As part of Core domain context restoration while coming out of off mode
there are some registers being restored which are not required to be restored.
ROM code will have restored them already. Overwriting some of them can have
potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked.
Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Current value is stored on SDRAM and it is written back during wakeup.
Previously a static value of 0x72 was written there.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Previously used u32 as temporary data storage that wraps around at 4.294s.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes code blocks that are repeated
in function prcm_setup_regs().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enable the auto-idle feature of the SCM block to save some additional
power.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Don't assume that gpmc_l3_clk is on, enable it before touching
configuration registers.
Note that the current code assumes that this clock is always
enabled. We are already setting smart idle and L3 autogating
for GPMC clock in gpmc_init.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 52650505fb caused clock initialization
to fail on OMAP1 with "BUG: spinlock lockup on CPU#0" -- this is because
omap1_select_table_rate() and omap1_round_to_table_rate() call clk_get_rate()
with the clockfw spinlock held. Fix by accessing the rate directly from
the internal clock framework functions.
Thanks to Tony Lindgren <tony@atomide.com> for reporting and testing the fix.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
For all DPLL's the valid dividers are same as the values
to be programmed in the register. 0 is an invalid value.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The CHIRONSS has its own local PRCM module and the register defines
need to use the CHIRONSS base and not the PRM base.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We need to set the omap_chip.oc carefully for the clocks to work.
To fix this, set the omap_chip.oc in omap3_check_features() based
on the CONTROL_IDCODE and silicon revision registers.
Also add handling for 34xx es3.1.2 as es3.1 for now.
Fixes booting on at least overo board.
Based on an earlier patch by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make the omap_mux_read and write available for board code,
and rename omap_mux_set_board_signals into omap_mux_write_array.
Also add the related prototypes and comments into mux.h.
In some cases we want to change the signals dynamically,
mostly for power management.
Note that we cannot use the signal names as they are set
__init to save memory.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like cmdline muxing got broken at some point when we
decided to limit muxing to __init code. Currently omap_mux_entry
list is not yet initialized when we try to initialize cmdline
muxing.
Fix this by calling omap_mux_init_list() before calling
omap_mux_set_cmdline_signals().
Reported-by: Philip Balister <philip@balister.org>
Tested-by: Philip Balister <philip@balister.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The first thing that omap2_init_clksel_parent() does is check for
a non-zero .clksel field in the struct clk. Therefore, it is
pointless calling this function on clocks where the clksel field
is unset.
Remove init calls to omap2_init_clksel_parent() on clocks without
a clksel field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the current implementation the sysconfig value is read into
_sysc_cache once and an actual update to the sysconfig register
happens only if the new value paased is differnt from the one in _sysc_cache.
_sysc_cache is updated only if _HWMOD_SYSCONFIG_LOADED is not set.
This can lead to the follwing issue if off mode is enabled in modules
which employs "always-retore" mechanism of context save and restore.
a. The module sets the sysconfig register through omap_device_enable.
Here _sysc_cache is updated with the value written to the sysconfig
register and left.
b. The power domain containig the module enters off mode and the
module context is lost.
c. The module in use becomes active and calls omap_device_enable to
enable itself. Here a read of sysconfig register does not happen
as _HWMOD_SYSCONFIG_LOADED flag is set. The value to be written
to the sysconfig register will be same as the one written in step a.
Since _sysc_cache reflects the previous written value an update
of the sysconfig register does not happen.
This means in modules which employs "always-restore" mechanism
after off , the sysconfig regsiters will never get updated.
This patch introduces a flag SYSC_NO_CACHE which if set ensures that the
sysconfig register is always read into _sysc_cache before an update is
attempted.
This flags need to be set only by modules which does not do a context save
but re-initializes the registers every time the module is accessed. This
includes modules like i2c, smartreflex etc.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: tweaked to apply on a different head, added flag comment]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The comments in cacheflush.h should follow what's in
struct cpu_cache_fns. The comments for V6 and V7 are
unnecessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The comments in arm_machine_restart() suggest that cpu_proc_fin()
will clean and disable cache and turn off interrupts. This does
not seem to be implemented for proc-v7.S, implement it the same
way as for proc-v6.S.
This also makes kexec work for v7. Note that a related TLB and
branch traget flush patch is also needed to avoid kexec
"crc error".
Note that there are still some issues that seem to be related
to L2 cache being on and causing occasional uncompress "crc error"
with kexec. Anyways, this gets kexec mostly working on V7 for now.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to do that if we tinker with the MMU entries.
This fixes the occasional bug with kexec where the new
fails to uncompress with "crc error". Most likely at
least kexec on v6 and v7 need this fix.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Without this patch arch/arm/compressed/head.S defaults to generic
DCC code that does not work for v7.
For more information on the v7 DCC, see Cortex-A8 TRM
"12.11.1 Debug communications channel".
To use it with post 2.6.33-rc1 or later, you need to have:
CONFIG_DEBUG_LL=y
ONFIG_DEBUG_ICEDCC=y
CONFIG_EARLY_PRINTK=y
Earlier kernels need commit 93fd03a8c6
backported.
Tested on omap3430.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 14f0aa3593.
That commit was needed earlier because system call restarting for
OABI (compat) required an executable stack and thus had problems
with NX. Since ab72b00734 ("ARM: Fix signal restart issues
with NX and OABI compat") has reworked the code to not require an
executable stack anymore, we can re-enable NX support for kernels
with OABI (compat) support.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Because of the include of the decompress_inflate.c file from
boot/compress/misc.c, there are different flush() defines:
In file included from arch/arm/boot/compressed/misc.c:249:
arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:138:29: error: macro "flush" passed 2 arguments, but takes just 0
Fix this by removing the define of flush() in misc.c for
CONFIG_DEBUG_ICEDCC as it's already defined in mach/uncompress.h,
and that is being included unconditionally.
Also use a static inline function instead of define
for mach-mxc and mach-gemini to avoid similar bug
for those platforms.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus/samsung' of git://git.fluff.org/bjdooks/linux:
ARM: MINI2440: Fixup __initdata usage
ARM: MINI2440: Fix crash on boot due to improper __initdata qualifier
ARM: SMDK6410: Specify no GPIO for B_PWR_5V regulator
ARM: S3C: NAND: Check the existence of nr_map before copying
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sentelic - fix left/right horizontal scroll mapping
Input: pmouse - move Sentelic probe down the list
Input: add compat support for sysfs and /proc capabilities output
Input: i8042 - add Dritek quirk for Acer Aspire 5610.
Input: xbox - do not use GFP_KERNEL under spinlock
Input: psmouse - fix Synaptics detection when protocol is disabled
Input: bcm5974 - report ABS_MT events
Input: davinci_keyscan - add device_enable method to platform data
Input: evdev - be less aggressive about sending SIGIO notifies
Input: atkbd - fix canceling event_work in disconnect
Input: serio - fix potential deadlock when unbinding drivers
Input: gf2k - fix &&/|| confusion in gf2k_connect()
Remove some of the __initdata tags which are currently inappropriate for
platform_device and some of the platform data. These can be returned once
support for copying platform devices and data is added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch fix mini2440 crash on boot due to improper __initdata
qualifier on mini2440_led1_pdata.
Signed-off-by: Uri Yosef <uri.yosef@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since the fixed voltage regulator grew support for GPIO based
enables and GPIO 0 is valid on some systems we need to specify
that there is no valid GPIO enable control.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since the structure field nr_map is optional, we need to check whether the
chip number map is provided to avoid unexpected NULL pointer exception.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
There is no such GPIO for udc vbus sensing, put '-1' instead of default
'0' as '0' does mean a valid GPIO.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
ARM: Fix wrong dmb
ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
ARM: 5867/1: Update U300 defconfig
ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
[ARM] pxa: fix strange characters in zaurus gpio .desc
ARM: add missing recvmmsg syscall number
[ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
[ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
[ARM] pxa: enable L2 if present in XSC3
[ARM] pxa: do not enable L2 after MMU is enabled
A kernel with both ARMv6 and ARMv7 selected results in build errors.
Fix this by specifying the proper architectures for these assembly
files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __kuser_cmpxchg code uses an ARMv6 dmb instruction, rather than
one based upon the architecture being built for. Switch to using
the macro provided for this purpose, which also eliminates the
need for an ifdef.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since AUDMUX configuration appears to be one of the common stumbling
blocks for people setting up i.MX audio try to provide some diagnostic
information describing the current setup to assisist people in working
out what's going on.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- changes to ach/arch/boot/Makefile to make it easier to add new
compression types
- new piggy.lzo.S necessary for lzo compression
- changes in arch/arm/boot/compressed/misc.c to allow the use of lzo or
gzip, depending on the config
- Kconfig support
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes it consistent with the extern declaration, used when CONFIG_HIGHMEM
is set Removes redundant casts in printout messages
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extend the patch from Philby John to the other "RealView" boards.
Rename the constants and offsets to reflect their actual functions.
Cc: Philby John <pjohn@in.mvista.com>
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The file arch/arm/include/asm/cpu.h needs to include 'linux/cpu.h' to
meet its dependency. Otherwise when using "struct cpuinfo_arm" and
including just 'asm/cpu.h' throws below error -
arch/arm/include/asm/cpu.h:16: error: field 'cpu' has incomplete type
To fix this otherway, one can also include both linux/cpu.h and
asm/cpu.h but it shoudn't be that way. So this patch fixes this by
including the linux/cpu.h in asm/cpu.h, so that including alone
asm/cpu.h is enough.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a build failure [1] due to missing includes
This should make the arm tree build again with lpd7a404_defconfig
References:
http://kisskb.ellerman.id.au/kisskb/buildresult/1983329/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A lot of ARM-defconfigs (those without CONFIG_ISA_DMA_API set) fail to
build [1][2][3] due to the changes of the patch
[PATCH] PCI: Clean up build for CONFIG_PCI_QUIRKS unset
by Rafael J. Wysocki (Sat, 2 Jan 2010 22:57:24 +0100) [4]
as the referenced variable 'isa_dma_bridge_buggy' in asm/dma.h is
enclosed by the CONFIG_ISA_DMA_API conditional all configs without this
setting fail to build.
I'm not sure wether moving the condition is the right way to solve the
issue, but atleast it fixes the issue :)
References:
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/1983354/
[2] http://kisskb.ellerman.id.au/kisskb/buildresult/1983333/
[3] http://kisskb.ellerman.id.au/kisskb/buildresult/1983337/
[4] http://lkml.org/lkml/2010/1/2/102
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dynamically allocate the CPUFreq frequency table on OMAP2xxx chips.
This fixes some compilation problems, since the kernel may not know
what chip it is running on until boot-time. This also reduces the size
of the CPUFreq frequency table.
Problem originally reported by Felipe Balbi <felipe.balbi@nokia.com>.
Thanks also for comments on the patch from Felipe and Kevin.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
A subsequent patch adds code on OMAP2xxx to dynamically allocate the
CPUFreq frequency table in clk_init_cpufreq_table(), so for it to
avoid a leak, it will need a corresponding function to free the
memory. This patch adds clk_exit_cpufreq_table() with generic
code to call a chip-specific variant inside the clockfw_lock spinlock via
struct clk_functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley