Turned out that "switchdev" sticks. So just unify all related terms to use
this prefix.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "ntohs(proto) >= ETH_P_802_3_MIN" w/ eth_proto_is_802_3(proto).
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BR_GROUPFWD_RESTRICTED bitmask restricts users from setting values to
/sys/class/net/brX/bridge/group_fwd_mask that allow forwarding of
some IEEE 802.1D Table 7-10 Reserved addresses:
(MAC Control) 802.3 01-80-C2-00-00-01
(Link Aggregation) 802.3 01-80-C2-00-00-02
802.1AB LLDP 01-80-C2-00-00-0E
Change BR_GROUPFWD_RESTRICTED to allow to forward LLDP frames and document
group_fwd_mask.
e.g.
echo 16384 > /sys/class/net/brX/bridge/group_fwd_mask
allows to forward LLDP frames.
This may be needed for bridge setups used for network troubleshooting or
any other scenario where forwarding of LLDP frames is desired (e.g. bridge
connecting a virtual machine to real switch transmitting LLDP frames that
virtual machine needs to receive).
Tested on a simple bridge setup with two interfaces and host transmitting
LLDP frames on one side of this bridge (used lldpd). Setting group_fwd_mask
as described above lets LLDP frames traverse bridge.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, the IGMP and MLD message validation functions are moved
from the bridge code to IPv4/IPv6 multicast files. Some small
refactoring was done to enhance readibility and to iron out some
differences in behaviour between the IGMP and MLD parsing code (e.g. the
skb-cloning of MLD messages is now only done if necessary, just like the
IGMP part always did).
Finally, these IGMP and MLD message validation functions are exported so
that not only the bridge can use it but batman-adv later, too.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's use these new, neat helpers.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 37a393bc49 ("bridge: notify mdb changes via netlink")
CC: Cong Wang <amwang@redhat.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the nf_tables registers from 128 bit addressing to 32 bit
addressing to support so called concatenations, where multiple values
can be concatenated over multiple registers for O(1) exact matches of
multiple dimensions using sets.
The old register values are mapped to areas of 128 bits for compatibility.
When dumping register numbers, values are expressed using the old values
if they refer to the beginning of a 128 bit area for compatibility.
To support concatenations, register loads of less than a full 32 bit
value need to be padded. This mainly affects the payload and exthdr
expressions, which both unconditionally zero the last word before
copying the data.
Userspace fully passes the testsuite using both old and new register
addressing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add helper functions to parse and dump register values in netlink attributes.
These helpers will later be changed to take care of translation between the
old 128 bit and the new 32 bit register numbers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simple conversion to use u32 pointers to the beginning of the registers
to keep follow up patches smaller.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Replace the array of registers passed to expressions by a struct nft_regs,
containing the verdict as a seperate member, which aliases to the
NFT_REG_VERDICT register.
This is needed to seperate the verdict from the data registers completely,
so their size can be changed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All users of nft_validate_register_store() first invoke
nft_validate_output_register(). There is in fact no use for using it
on its own, so simplify the code by folding the functionality into
nft_validate_register_store() and kill it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The existing name is ambiguous, data is loaded as well when we read from
a register. Rename to nft_validate_register_store() for clarity and
consistency with the upcoming patch to introduce its counterpart,
nft_validate_register_load().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For values spanning multiple registers, we need to validate that enough
space is available from the destination register onwards. Add a len
argument to nft_validate_data_load() and consolidate the existing length
validations in preparation of that.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree.
They are:
* nf_tables set timeout infrastructure from Patrick Mchardy.
1) Add support for set timeout support.
2) Add support for set element timeouts using the new set extension
infrastructure.
4) Add garbage collection helper functions to get rid of stale elements.
Elements are accumulated in a batch that are asynchronously released
via RCU when the batch is full.
5) Add garbage collection synchronization helpers. This introduces a new
element busy bit to address concurrent access from the netlink API and the
garbage collector.
5) Add timeout support for the nft_hash set implementation. The garbage
collector peridically checks for stale elements from the workqueue.
* iptables/nftables cgroup fixes:
6) Ignore non full-socket objects from the input path, otherwise cgroup
match may crash, from Daniel Borkmann.
7) Fix cgroup in nf_tables.
8) Save some cycles from xt_socket by skipping packet header parsing when
skb->sk is already set because of early demux. Also from Daniel.
* br_netfilter updates from Florian Westphal.
9) Save frag_max_size and restore it from the forward path too.
10) Use a per-cpu area to restore the original source MAC address when traffic
is DNAT'ed.
11) Add helper functions to access physical devices.
12) Use these new physdev helper function from xt_physdev.
13) Add another nf_bridge_info_get() helper function to fetch the br_netfilter
state information.
14) Annotate original layer 2 protocol number in nf_bridge info, instead of
using kludgy flags.
15) Also annotate the pkttype mangling when the packet travels back and forth
from the IP to the bridge layer, instead of using a flag.
* More nf_tables set enhancement from Patrick:
16) Fix possible usage of set variant that doesn't support timeouts.
17) Avoid spurious "set is full" errors from Netlink API when there are pending
stale elements scheduled to be released.
18) Restrict loop checks to set maps.
19) Add support for dynamic set updates from the packet path.
20) Add support to store optional user data (eg. comments) per set element.
BTW, I have also pulled net-next into nf-next to anticipate the conflict
resolution between your okfn() signature changes and Florian's br_netfilter
updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
More recent GCC warns about two kinds of switch statement uses:
1) Switching on an enumeration, but not having an explicit case
statement for all members of the enumeration. To show the
compiler this is intentional, we simply add a default case
with nothing more than a break statement.
2) Switching on a boolean value. I think this warning is dumb
but nevertheless you get it wholesale with -Wswitch.
This patch cures all such warnings in netfilter.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_bridge_info->mask is used for several things, for example to
remember if skb->pkt_type was set to OTHER_HOST.
For a bridge, OTHER_HOST is expected case. For ip forward its a non-starter
though -- routing expects PACKET_HOST.
Bridge netfilter thus changes OTHER_HOST to PACKET_HOST before hook
invocation and then un-does it after hook traversal.
This information is irrelevant outside of br_netfilter.
After this change, ->mask now only contains flags that need to be
known outside of br_netfilter in fast-path.
Future patch changes mask into a 2bit state field in sk_buff, so that
we can remove skb->nf_bridge pointer for good and consider all remaining
places that access nf_bridge info content a not-so fastpath.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
->mask is a bit info field that mixes various use cases.
In particular, we have flags that are mutually exlusive, and flags that
are only used within br_netfilter while others need to be exposed to
other parts of the kernel.
Remove BRNF_8021Q/PPPoE flags. They're mutually exclusive and only
needed within br_netfilter context.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Don't access skb->nf_bridge directly, this pointer will be removed soon.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
br_netfilter maintains an extra state, nf_bridge_info, which is attached
to skb via skb->nf_bridge pointer.
Amongst other things we use skb->nf_bridge->data to store the original
mac header for every processed skb.
This is required for ip refragmentation when using conntrack
on top of bridge, because ip_fragment doesn't copy it from original skb.
However there is no need anymore to do this unconditionally.
Move this to the one place where its needed -- when br_netfilter calls
ip_fragment().
Also switch to percpu storage for this so we can handle fragmenting
without accessing nf_bridge meta data.
Only user left is neigh resolution when DNAT is detected, to hold
the original source mac address (neigh resolution builds new mac header
using bridge mac), so rename ->data and reduce its size to whats needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On the output paths in particular, we have to sometimes deal with two
socket contexts. First, and usually skb->sk, is the local socket that
generated the frame.
And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.
We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.
The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device. We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to prepare the removal of the iflink field. It
introduces a new ndo function, which will be implemented by virtual interfaces.
There is no functional change into this patch. All readers of iflink field
now call dev_get_iflink().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We also need to save/store in forward, else br_parse_ip_options call
will zero frag_max_size as well.
Fixes: 93fdd47e5 ('bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING')
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next.
Basically, more incremental updates for br_netfilter from Florian
Westphal, small nf_tables updates (including one fix for rb-tree
locking) and small two-liner to add extra validation for the REJECT6
target.
More specifically, they are:
1) Use the conntrack status flags from br_netfilter to know that DNAT is
happening. Patch for Florian Westphal.
2) nf_bridge->physoutdev == NULL already indicates that the traffic is
bridged, so let's get rid of the BRNF_BRIDGED flag. Also from Florian.
3) Another patch to prepare voidization of seq_printf/seq_puts/seq_putc,
from Joe Perches.
4) Consolidation of nf_tables_newtable() error path.
5) Kill nf_bridge_pad used by br_netfilter from ip_fragment(),
from Florian Westphal.
6) Access rb-tree root node inside the lock and remove unnecessary
locking from the get path (we already hold nfnl_lock there), from
Patrick McHardy.
7) You cannot use a NFT_SET_ELEM_INTERVAL_END when the set doesn't
support interval, also from Patrick.
8) Enforce IP6T_F_PROTO from ip6t_REJECT to make sure the core is
actually restricting matches to TCP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The br_netfilter frag output function calls skb_cow_head() so in
case it needs a larger headroom to e.g. re-add a previously stripped PPPOE
or VLAN header things will still work (at cost of reallocation).
We can then move nf_bridge_encap_header_len to br_netfilter.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Its not needed anymore since 2bf540b73e
([NETFILTER]: bridge-netfilter: remove deferred hooks).
Before this it was possible to have physoutdev set for locally generated
packets -- this isn't the case anymore:
BRNF_STATE_BRIDGED flag is set when we assign nf_bridge->physoutdev,
so physoutdev != NULL means BRNF_STATE_BRIDGED is set.
If physoutdev is NULL, then we are looking at locally-delivered and
routed packet.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ask conntrack instead of storing ipv4 address in nf_bridge_info->data.
Ths avoids the need to use ->data during NF_PRE_ROUTING.
Only two functions that need ->data remain.
These will be addressed in followup patches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On adding an interface br_add_if() sets the MTU to the min of
all the interfaces. Do the same thing on removing an interface too
in br_del_if.
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e5de75b ("netfilter: bridge: move DNAT helper to br_netfilter") results
in the following link problem:
net/bridge/br_device.c:29: undefined reference to `br_nf_prerouting_finish_bridge`
Moreover it creates a hard dependency between br_netfilter and the
bridge core, which is what we've been trying to avoid so far.
Resolve this problem by using a hook structure so we reduce #ifdef
pollution and keep bridge netfilter specific code under br_netfilter.c
which was the original intention.
Reported-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
make C=1 CF=-D__CHECK_ENDIAN__ shows following:
net/bridge/netfilter/nft_reject_bridge.c:65:50: warning: incorrect type in argument 3 (different base types)
net/bridge/netfilter/nft_reject_bridge.c:65:50: expected restricted __be16 [usertype] protocol [..]
net/bridge/netfilter/nft_reject_bridge.c:102:37: warning: cast from restricted __be16
net/bridge/netfilter/nft_reject_bridge.c:102:37: warning: incorrect type in argument 1 (different base types) [..]
net/bridge/netfilter/nft_reject_bridge.c:121:50: warning: incorrect type in argument 3 (different base types) [..]
net/bridge/netfilter/nft_reject_bridge.c:168:52: warning: incorrect type in argument 3 (different base types) [..]
net/bridge/netfilter/nft_reject_bridge.c:233:52: warning: incorrect type in argument 3 (different base types) [..]
Caused by two (harmless) errors:
1. htons() instead of ntohs()
2. __be16 for protocol in nf_reject_ipXhdr_put API, use u8 instead.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After my change to neigh_hh_init to obtain the protocol from the
neigh_table there are no more users of protocol in struct dst_ops.
Remove the protocol field from dst_ops and all of it's initializers.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, improvements for the packet rejection infrastructure,
deprecation of CLUSTERIP, cleanups for nf_tables and some untangling for
br_netfilter. More specifically they are:
1) Send packet to reset flow if checksum is valid, from Florian Westphal.
2) Fix nf_tables reject bridge from the input chain, also from Florian.
3) Deprecate the CLUSTERIP target, the cluster match supersedes it in
functionality and it's known to have problems.
4) A couple of cleanups for nf_tables rule tracing infrastructure, from
Patrick McHardy.
5) Another cleanup to place transaction declarations at the bottom of
nf_tables.h, also from Patrick.
6) Consolidate Kconfig dependencies wrt. NF_TABLES.
7) Limit table names to 32 bytes in nf_tables.
8) mac header copying in bridge netfilter is already required when
calling ip_fragment(), from Florian Westphal.
9) move nf_bridge_update_protocol() to br_netfilter.c, also from
Florian.
10) Small refactor in br_netfilter in the transmission path, again from
Florian.
11) Move br_nf_pre_routing_finish_bridge_slow() to br_netfilter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one caller, there is no need to keep this in a header.
Move it to br_netfilter.c where this belongs to.
Based on patch from Florian Westphal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The mac header only has to be copied back into the skb for
fragments generated by ip_fragment(), which only happens
for bridge forwarded packets with nf-call-iptables=1 && active nf_defrag.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This extends the design in commit 958501163d ("bridge: Add support for
IEEE 802.11 Proxy ARP") with optional set of rules that are needed to
meet the IEEE 802.11 and Hotspot 2.0 requirements for ProxyARP. The
previously added BR_PROXYARP behavior is left as-is and a new
BR_PROXYARP_WIFI alternative is added so that this behavior can be
configured from user space when required.
In addition, this enables proxyarp functionality for unicast ARP
requests for both BR_PROXYARP and BR_PROXYARP_WIFI since it is possible
to use unicast as well as broadcast for these frames.
The key differences in functionality:
BR_PROXYARP:
- uses the flag on the bridge port on which the request frame was
received to determine whether to reply
- block bridge port flooding completely on ports that enable proxy ARP
BR_PROXYARP_WIFI:
- uses the flag on the bridge port to which the target device of the
request belongs
- block bridge port flooding selectively based on whether the proxyarp
functionality replied
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the STP timer fires, it can call br_ifinfo_notify(),
which in turn ends up in the new br_get_link_af_size().
This function is annotated to be using RTNL locking, which
clearly isn't the case here, and thus lockdep warns:
===============================
[ INFO: suspicious RCU usage. ]
3.19.0+ #569 Not tainted
-------------------------------
net/bridge/br_private.h:204 suspicious rcu_dereference_protected() usage!
Fix this by doing RCU locking here.
Fixes: b7853d73e3 ("bridge: add vlan info to bridge setlink and dellink notification messages")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
make build fail if structure no longer fits into ->cb storage.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge reject handling is not straightforward, there are many subtle
differences depending on configuration.
skb->dev is either the bridge port (PRE_ROUTING) or the bridge
itself (INPUT), so we need to use indev instead.
Also, checksum validation will only work reliably if we trim skb
according to the l3 header size.
While at it, add csum validation for ipv6 and skip existing tests
if skb was already checked e.g. by GRO.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
my previous patch skipped vlan range optimizations during skb size
calculations for simplicity.
This incremental patch considers vlan ranges during
skb size calculations. This leads to a bit of code duplication
in the fill and size calculation functions. But, I could not find a
prettier way to do this. will take any suggestions.
Previously, I had reused the existing br_get_link_af_size size calculation
function to calculate skb size for notifications. Reusing it this time
around creates some change in behaviour issues for the usual
.get_link_af_size callback.
This patch adds a new br_get_link_af_size_filtered() function to
base the size calculation on the incoming filter flag and include
vlan ranges.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan add/deletes are not notified to userspace today. This patch adds
vlan info to bridge newlink/dellink notifications generated from the
bridge driver. Notifications use the RTEXT_FILTER_BRVLAN_COMPRESSED
flag to compress vlans into ranges whereever applicable.
The size calculations does not take ranges into account for
simplicity. This has the potential for allocating a larger skb than
required.
There is an existing inconsistency with bridge NEWLINK and DELLINK
change notifications. Both generate NEWLINK notifications. Since its
always a NEWLINK notification, this patch includes all vlans the port
belongs to in the notification. The NEWLINK and DELLINK request
messages however only include the vlans to be added and deleted.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_SYSCTL=n:
net/bridge/br_netfilter.c: In function ‘br_netfilter_init’:
net/bridge/br_netfilter.c:996: warning: label ‘err1’ defined but not used
Move the label and the code after it inside the existing #ifdef to get
rid of the warning.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge's default_pvid adds a vid by default, by which we cannot add a
non-vlan fdb entry by default, because br_fdb_add() adds fdb entries for
all vlans instead of a non-vlan one when any vlan is configured.
# ip link add br0 type bridge
# ip link set eth0 master br0
# bridge fdb add 12:34:56:78:90:ab dev eth0 master temp
# bridge fdb show brport eth0 | grep 12:34:56:78:90:ab
12:34:56:78:90:ab dev eth0 vlan 1 static
We expect a non-vlan fdb entry as well as vlan 1:
12:34:56:78:90:ab dev eth0 static
To fix this, we need to insert a non-vlan fdb entry if vlan is not
specified, even when any vlan is configured.
Fixes: 5be5a2df40 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a missing bridge port check caught by smatch.
setlink/dellink of attributes like vlans can come for a bridge device
and there is no need to offload those today. So, this patch adds a bridge
port check. (In these cases however, the BRIDGE_SELF flags will always be set
and we may not hit a problem with the current code).
smatch complaint:
The patch 68e331c785b8: "bridge: offload bridge port attributes to
switch asic if feature flag set" from Jan 29, 2015, leads to the
following Smatch complaint:
net/bridge/br_netlink.c:552 br_setlink()
error: we previously assumed 'p' could be null (see line 518)
net/bridge/br_netlink.c
517
518 if (p && protinfo) {
^
Check for NULL.
Reported-By: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
When 'learned_sync' flag is turned on, the offloaded switch
port syncs learned MAC addresses to bridge's FDB via switchdev notifier
(NETDEV_SWITCH_FDB_ADD). Currently, FDB entries learnt via this mechanism are
wrongly being deleted by bridge aging logic. This patch ensures that FDB
entries synced from offloaded switch ports are not deleted by bridging logic.
Such entries can only be deleted via switchdev notifier
(NETDEV_SWITCH_FDB_DEL).
Signed-off-by: Siva Mannem <siva.mannem.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to set/del bridge port attributes in hardware from
the bridge driver.
With this, when the user sends a bridge setlink message with no flags or
master flags set,
- the bridge driver ndo_bridge_setlink handler sets settings in the kernel
- calls the swicthdev api to propagate the attrs to the switchdev
hardware
You can still use the self flag to go to the switch hw or switch port
driver directly.
With this, it also makes sure a notification goes out only after the
attributes are set both in the kernel and hw.
The patch calls switchdev api only if BRIDGE_FLAGS_SELF is not set.
This is because the offload cases with BRIDGE_FLAGS_SELF are handled in
the caller (in rtnetlink.c).
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are all either written once or extremly rarely (e.g. from init
code), so we can move them to the .data..read_mostly section.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static checkers complain that we should maybe set "ret" before we do the
"goto out;". They interpret the NULL return from br_port_get_rtnl() as
a failure and forgetting to set the error code is a common bug in this
situation.
The code is confusing but it's actually correct. We are returning zero
deliberately. Let's re-write it a bit to be more clear.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA-enabled master network devices with a switch tagging protocol should
strip the protocol specific format before handing the frame over to
higher layer.
When adding such a DSA master network device as a bridge member, we go
through the following code path when receiving a frame:
__netif_receive_skb_core
-> first ptype check against ptype_all is not returning any
handler for this skb
-> check and invoke rx_handler:
-> deliver frame to the bridge layer: br_handle_frame
DSA registers a ptype handler with the fake ETH_XDSA ethertype, which is
called *after* the bridge-layer rx_handler has run. br_handle_frame()
tries to parse the frame it received from the DSA master network device,
and will not be able to match any of its conditions and jumps straight
at the end of the end of br_handle_frame() and returns
RX_HANDLER_CONSUMED there.
Since we returned RX_HANDLER_CONSUMED, __netif_receive_skb_core() stops
RX processing for this frame and returns NET_RX_SUCCESS, so we never get
a chance to call our switch tag packet processing logic and deliver
frames to the DSA slave network devices, and so we do not get any
functional bridge members at all.
Instead of cluttering the bridge receive path with DSA-specific checks,
and rely on assumptions about how __netif_receive_skb_core() is
processing frames, we simply deny adding the DSA master network device
(conduit interface) as a bridge member, leaving only the slave DSA
network devices to be bridge members, since those will work correctly in
all circumstances.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user can crash the kernel if it uses any of the existing NAT
expressions from the wrong hook, so add some code to validate this
when loading the rule.
This patch introduces nft_chain_validate_hooks() which is based on
an existing function in the bridge version of the reject expression.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch benefits from newly introduced switchdev notifier and uses it
to propagate fdb learn events from rocker driver to bridge. That avoids
direct function calls and possible use by other listeners (ovs).
Suggested-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
problems with bridge getlink/setlink notifications today:
- bridge setlink generates two notifications to userspace
- one from the bridge driver
- one from rtnetlink.c (rtnl_bridge_notify)
- dellink generates one notification from rtnetlink.c. Which
means bridge setlink and dellink notifications are not
consistent
- Looking at the code it appears,
If both BRIDGE_FLAGS_MASTER and BRIDGE_FLAGS_SELF were set,
the size calculation in rtnl_bridge_notify can be wrong.
Example: if you set both BRIDGE_FLAGS_MASTER and BRIDGE_FLAGS_SELF
in a setlink request to rocker dev, rtnl_bridge_notify will
allocate skb for one set of bridge attributes, but,
both the bridge driver and rocker dev will try to add
attributes resulting in twice the number of attributes
being added to the skb. (rocker dev calls ndo_dflt_bridge_getlink)
There are multiple options:
1) Generate one notification including all attributes from master and self:
But, I don't think it will work, because both master and self may use
the same attributes/policy. Cannot pack the same set of attributes in a
single notification from both master and slave (duplicate attributes).
2) Generate one notification from master and the other notification from
self (This seems to be ideal):
For master: the master driver will send notification (bridge in this
example)
For self: the self driver will send notification (rocker in the above
example. It can use helpers from rtnetlink.c to do so. Like the
ndo_dflt_bridge_getlink api).
This patch implements 2) (leaving the 'rtnl_bridge_notify' around to be used
with 'self').
v1->v2 :
- rtnl_bridge_notify is now called only for self,
so, remove 'BRIDGE_FLAGS_SELF' check and cleanup a few things
- rtnl_bridge_dellink used to always send a RTM_NEWLINK msg
earlier. So, I have changed the notification from br_dellink to
go as RTM_NEWLINK
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a cleanup, because in the current code MDBA_SET_ENTRY_MAX ==
MDBA_SET_ENTRY.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPV4 support is disabled, we cannot call arp_send from
the bridge code, which would result in a kernel link error:
net/built-in.o: In function `br_handle_frame_finish':
:(.text+0x59914): undefined reference to `arp_send'
:(.text+0x59a50): undefined reference to `arp_tbl'
This makes the newly added proxy ARP support in the bridge
code depend on the CONFIG_INET symbol and lets the compiler
optimize the code out to avoid the link error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 958501163d ("bridge: Add support for IEEE 802.11 Proxy ARP")
Cc: Kyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/bridge/br_netlink.c: In function ‘br_fill_ifinfo’:
net/bridge/br_netlink.c:146:32: warning: ‘vid_range_flags’ may be used uninitialized in this function [-Wmaybe-uninitialized]
err = br_fill_ifvlaninfo_range(skb, vid_range_start,
^
net/bridge/br_netlink.c:108:6: note: ‘vid_range_flags’ was declared here
u16 vid_range_flags;
Reported-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new function to pack vlans into ranges
whereever applicable using the flags BRIDGE_VLAN_INFO_RANGE_BEGIN
and BRIDGE VLAN_INFO_RANGE_END
Old vlan packing code is moved to a new function and continues to be
called when filter_mask is RTEXT_FILTER_BRVLAN.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes bridge IFLA_AF_SPEC netlink attribute parser to
look for more than one IFLA_BRIDGE_VLAN_INFO attribute. This allows
userspace to pack more than one vlan in the setlink msg.
The dumps were already sending more than one vlan info in the getlink msg.
This patch also adds bridge_vlan_info flags BRIDGE_VLAN_INFO_RANGE_BEGIN and
BRIDGE_VLAN_INFO_RANGE_END to indicate start and end of vlan range
This patch also deletes unused ifla_br_policy.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a bridge device turns off TSO feature if no bridge ports
support it. We can always enable it, since packets can be segmented on
ports by software as well as on the bridge device.
This will reduce the number of packets processed in the bridge.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checking whether the call to ndo_dflt_fdb_dump is needed.
It is not expected to call ndo_dflt_fdb_dump unconditionally
by some drivers (i.e. qlcnic or macvlan) that defines
own ndo_fdb_dump. Other drivers define own ndo_fdb_dump
and don't want ndo_dflt_fdb_dump to be called at all.
At the same time it is desirable to call the default dump
function on a bridge device.
Fix attributes that are passed to dev->netdev_ops->ndo_fdb_dump.
Add extra checking in br_fdb_dump to avoid duplicate entries
as now filter_dev can be NULL.
Following tests for filtering have been performed before
the change and after the patch was applied to make sure
they are the same and it doesn't break the filtering algorithm.
[root@localhost ~]# cd /root/iproute2-3.18.0/bridge
[root@localhost bridge]# modprobe dummy
[root@localhost bridge]# ./bridge fdb add f1:f2:f3:f4:f5:f6 dev dummy0
[root@localhost bridge]# brctl addbr br0
[root@localhost bridge]# brctl addif br0 dummy0
[root@localhost bridge]# ip link set dev br0 address 02:00:00:12:01:04
[root@localhost bridge]# # show all
[root@localhost bridge]# ./bridge fdb show
33:33:00:00:00:01 dev p2p1 self permanent
01:00:5e:00:00:01 dev p2p1 self permanent
33:33:ff:ac:ce:32 dev p2p1 self permanent
33:33:00:00:02:02 dev p2p1 self permanent
01:00:5e:00:00:fb dev p2p1 self permanent
33:33:00:00:00:01 dev p7p1 self permanent
01:00:5e:00:00:01 dev p7p1 self permanent
33:33:ff:79:50:53 dev p7p1 self permanent
33:33:00:00:02:02 dev p7p1 self permanent
01:00:5e:00:00:fb dev p7p1 self permanent
f2:46:50:85:6d:d9 dev dummy0 master br0 permanent
f2:46:50:85:6d:d9 dev dummy0 vlan 1 master br0 permanent
33:33:00:00:00:01 dev dummy0 self permanent
f1:f2:f3:f4:f5:f6 dev dummy0 self permanent
33:33:00:00:00:01 dev br0 self permanent
02:00:00:12:01:04 dev br0 vlan 1 master br0 permanent
02:00:00:12:01:04 dev br0 master br0 permanent
[root@localhost bridge]# # filter by bridge
[root@localhost bridge]# ./bridge fdb show br br0
f2:46:50:85:6d:d9 dev dummy0 master br0 permanent
f2:46:50:85:6d:d9 dev dummy0 vlan 1 master br0 permanent
33:33:00:00:00:01 dev dummy0 self permanent
f1:f2:f3:f4:f5:f6 dev dummy0 self permanent
33:33:00:00:00:01 dev br0 self permanent
02:00:00:12:01:04 dev br0 vlan 1 master br0 permanent
02:00:00:12:01:04 dev br0 master br0 permanent
[root@localhost bridge]# # filter by port
[root@localhost bridge]# ./bridge fdb show brport dummy0
f2:46:50:85:6d:d9 master br0 permanent
f2:46:50:85:6d:d9 vlan 1 master br0 permanent
33:33:00:00:00:01 self permanent
f1:f2:f3:f4:f5:f6 self permanent
[root@localhost bridge]# # filter by port + bridge
[root@localhost bridge]# ./bridge fdb show br br0 brport dummy0
f2:46:50:85:6d:d9 master br0 permanent
f2:46:50:85:6d:d9 vlan 1 master br0 permanent
33:33:00:00:00:01 self permanent
f1:f2:f3:f4:f5:f6 self permanent
[root@localhost bridge]#
Signed-off-by: Hubert Sokolowski <hubert.sokolowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following batch contains netfilter updates for net-next. Basically,
enhancements for xt_recent, skip zeroing of timer in conntrack, fix
linking problem with recent redirect support for nf_tables, ipset
updates and a couple of cleanups. More specifically, they are:
1) Rise maximum number per IP address to be remembered in xt_recent
while retaining backward compatibility, from Florian Westphal.
2) Skip zeroing timer area in nf_conn objects, also from Florian.
3) Inspect IPv4 and IPv6 traffic from the bridge to allow filtering using
using meta l4proto and transport layer header, from Alvaro Neira.
4) Fix linking problems in the new redirect support when CONFIG_IPV6=n
and IP6_NF_IPTABLES=n.
And ipset updates from Jozsef Kadlecsik:
5) Support updating element extensions when the set is full (fixes
netfilter bugzilla id 880).
6) Fix set match with 32-bits userspace / 64-bits kernel.
7) Indicate explicitly when /0 networks are supported in ipset.
8) Simplify cidr handling for hash:*net* types.
9) Allocate the proper size of memory when /0 networks are supported.
10) Explicitly add padding elements to hash:net,net and hash:net,port,
because the elements must be u32 sized for the used hash function.
Jozsef is also cooking ipset RCU conversion which should land soon if
they reach the merge window in time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
When the swdev device learns a new mac/vlan on a port, it sends some async
notification to the driver and the driver installs an FDB in the device.
To give a holistic system view, the learned mac/vlan should be reflected
in the bridge's FBD table, so the user, using normal iproute2 cmds, can view
what is currently learned by the device. This API on the bridge driver gives
a way for the swdev driver to install an FBD entry in the bridge FBD table.
(And remove one).
This is equivalent to the device running these cmds:
bridge fdb [add|del] <mac> dev <dev> vid <vlan id> master
This patch needs some extra eyeballs for review, in paricular around the
locking and contexts.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To notify switch driver of change in STP state of bridge port, add new
.ndo op and provide switchdev wrapper func to call ndo op. Use it in bridge
code then.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current name might seem that this actually offloads the fdb entry to
hw. So rename it to clearly present that this for hardware address
addition/removal.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing bits to allow to match per meta l4proto from
the bridge. Example:
nft add rule bridge filter input ether type {ip, ip6} meta l4proto udp counter
Signed-off-by: Alvaro Neira Ayuso <alvaroneay@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch exports the functions nft_reject_iphdr_validate and
nft_reject_ip6hdr_validate to use it in follow up patches.
These functions check if the IPv4/IPv6 header is correct.
Signed-off-by: Alvaro Neira Ayuso <alvaroneay@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes: c2d3babf ("bridge: implement multicast fast leave")
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter/ipvs updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, this includes the NAT redirection support for nf_tables, the
cgroup support for nft meta and conntrack zone support for the connlimit
match. Coming after those, a bunch of sparse warning fixes, missing
netns bits and cleanups. More specifically, they are:
1) Prepare IPv4 and IPv6 NAT redirect code to use it from nf_tables,
patches from Arturo Borrero.
2) Introduce the nf_tables redir expression, from Arturo Borrero.
3) Remove an unnecessary assignment in ip_vs_xmit/__ip_vs_get_out_rt().
Patch from Alex Gartrell.
4) Add nft_log_dereference() macro to the nf_log infrastructure, patch
from Marcelo Leitner.
5) Add some extra validation when registering logger families, also
from Marcelo.
6) Some spelling cleanups from stephen hemminger.
7) Fix sparse warning in nf_logger_find_get().
8) Add cgroup support to nf_tables meta, patch from Ana Rey.
9) A Kconfig fix for the new redir expression and fix sparse warnings in
the new redir expression.
10) Fix several sparse warnings in the netfilter tree, from
Florian Westphal.
11) Reduce verbosity when OOM in nfnetlink_log. User can basically do
nothing when this situation occurs.
12) Add conntrack zone support to xt_connlimit, again from Florian.
13) Add netnamespace support to the h323 conntrack helper, contributed
by Vasily Averin.
14) Remove unnecessary nul-pointer checks before free_percpu() and
module_put(), from Markus Elfring.
15) Use pr_fmt in nfnetlink_log, again patch from Marcelo Leitner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
Name fits better. Plus there's going to be introduced
__vlan_insert_tag later on.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ebtables on the OUTPUT chain (NF_BR_LOCAL_OUT) would not work as expected
for both locally generated IGMP and MLD queries. The IP header specific
filter options are off by 14 Bytes for netfilter (actual output on
interfaces is fine).
NF_HOOK() expects the skb->data to point to the IP header, not the
ethernet one (while dev_queue_xmit() does not). Luckily there is an
br_dev_queue_push_xmit() helper function already - let's just use that.
Introduced by eb1d164143
("bridge: Add core IGMP snooping support")
Ebtables example:
$ ebtables -I OUTPUT -p IPv6 -o eth1 --logical-out br0 \
--log --log-level 6 --log-ip6 --log-prefix="~EBT: " -j DROP
before (broken):
~EBT: IN= OUT=eth1 MAC source = 02:04:64:a4:39:c2 \
MAC dest = 33:33:00:00:00:01 proto = 0x86dd IPv6 \
SRC=64a4:39c2:86dd:6000:0000:0020:0001:fe80 IPv6 \
DST=0000:0000:0000:0004:64ff:fea4:39c2:ff02, \
IPv6 priority=0x3, Next Header=2
after (working):
~EBT: IN= OUT=eth1 MAC source = 02:04:64:a4:39:c2 \
MAC dest = 33:33:00:00:00:01 proto = 0x86dd IPv6 \
SRC=fe80:0000:0000:0000:0004:64ff:fea4:39c2 IPv6 \
DST=ff02:0000:0000:0000:0000:0000:0000:0001, \
IPv6 priority=0x0, Next Header=0
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
net/bridge/br_netfilter.c:870:6: symbol 'br_netfilter_enable' was not declared. Should it be static?
no; add include
net/ipv4/netfilter/nft_reject_ipv4.c:22:6: symbol 'nft_reject_ipv4_eval' was not declared. Should it be static?
yes
net/ipv6/netfilter/nf_reject_ipv6.c:16:6: symbol 'nf_send_reset6' was not declared. Should it be static?
no; add include
net/ipv6/netfilter/nft_reject_ipv6.c:22:6: symbol 'nft_reject_ipv6_eval' was not declared. Should it be static?
yes
net/netfilter/core.c:33:32: symbol 'nf_ipv6_ops' was not declared. Should it be static?
no; add include
net/netfilter/xt_DSCP.c:40:57: cast truncates bits from constant value (ffffff03 becomes 3)
net/netfilter/xt_DSCP.c:57:59: cast truncates bits from constant value (ffffff03 becomes 3)
add __force, 3 is what we want.
net/ipv4/netfilter/nf_log_arp.c:77:6: symbol 'nf_log_arp_packet' was not declared. Should it be static?
yes
net/ipv4/netfilter/nf_reject_ipv4.c:17:6: symbol 'nf_send_reset' was not declared. Should it be static?
no; add include
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix:
net/bridge/netfilter/nft_reject_bridge.c:
In function 'nft_reject_br_send_v6_unreach':
net/bridge/netfilter/nft_reject_bridge.c:240:3:
error: implicit declaration of function 'csum_ipv6_magic'
csum_ipv6_magic(&nip6h->saddr, &nip6h->daddr,
^
make[3]: *** [net/bridge/netfilter/nft_reject_bridge.o] Error 1
Seen with powerpc:allmodconfig.
Fixes: 523b929d54 ("netfilter: nft_reject_bridge: don't use IP stack to reject traffic")
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict the reject expression to the prerouting and input bridge
hooks. If we allow this to be used from forward or any other later
bridge hook, if the frame is flooded to several ports, we'll end up
sending several reject packets, one per cloned packet.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the packet is received via the bridge stack, this cannot reject
packets from the IP stack.
This adds functions to build the reject packet and send it from the
bridge stack. Comments and assumptions on this patch:
1) Validate the IPv4 and IPv6 headers before further processing,
given that the packet comes from the bridge stack, we cannot assume
they are clean. Truncated packets are dropped, we follow similar
approach in the existing iptables match/target extensions that need
to inspect layer 4 headers that is not available. This also includes
packets that are directed to multicast and broadcast ethernet
addresses.
2) br_deliver() is exported to inject the reject packet via
bridge localout -> postrouting. So the approach is similar to what
we already do in the iptables reject target. The reject packet is
sent to the bridge port from which we have received the original
packet.
3) The reject packet is forged based on the original packet. The TTL
is set based on sysctl_ip_default_ttl for IPv4 and per-net
ipv6.devconf_all hoplimit for IPv6.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This feature is defined in IEEE Std 802.11-2012, 10.23.13. It allows
the AP devices to keep track of the hardware-address-to-IP-address
mapping of the mobile devices within the WLAN network.
The AP will learn this mapping via observing DHCP, ARP, and NS/NA
frames. When a request for such information is made (i.e. ARP request,
Neighbor Solicitation), the AP will respond on behalf of the
associated mobile device. In the process of doing so, the AP will drop
the multicast request frame that was intended to go out to the wireless
medium.
It was recommended at the LKS workshop to do this implementation in
the bridge layer. vxlan.c is already doing something very similar.
The DHCP snooping code will be added to the userspace application
(hostapd) per the recommendation.
This RFC commit is only for IPv4. A similar approach in the bridge
layer will be taken for IPv6 as well.
Signed-off-by: Kyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 462fb2af97
bridge : Sanitize skb before it enters the IP stack
broke when IP options are actually used because it mangles the
skb as if it entered the IP stack which is wrong because the
bridge is supposed to operate below the IP stack.
Since nobody has actually requested for parsing of IP options
this patch fixes it by simply reverting to the previous approach
of ignoring all IP options, i.e., zeroing the IPCB.
If and when somebody who uses IP options and actually needs them
to be parsed by the bridge complains then we can revisit this.
Reported-by: David Newall <davidn@davidnewall.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As we may defragment the packet in IPv4 PRE_ROUTING and refragment
it after POST_ROUTING we should save the value of frag_max_size.
This is still very wrong as the bridge is supposed to leave the
packets intact, meaning that the right thing to do is to use the
original frag_list for fragmentation.
Unfortunately we don't currently guarantee that the frag_list is
left untouched throughout netfilter so until this changes this is
the best we can do.
There is also a spot in FORWARD where it appears that we can
forward a packet without going through fragmentation, mark it
so that we can fix it later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains another batch with Netfilter/IPVS updates
for net-next, they are:
1) Add abstracted ICMP codes to the nf_tables reject expression. We
introduce four reasons to reject using ICMP that overlap in IPv4
and IPv6 from the semantic point of view. This should simplify the
maintainance of dual stack rule-sets through the inet table.
2) Move nf_send_reset() functions from header files to per-family
nf_reject modules, suggested by Patrick McHardy.
3) We have to use IS_ENABLED(CONFIG_BRIDGE_NETFILTER) everywhere in the
code now that br_netfilter can be modularized. Convert remaining spots
in the network stack code.
4) Use rcu_barrier() in the nf_tables module removal path to ensure that
we don't leave object that are still pending to be released via
call_rcu (that may likely result in a crash).
5) Remove incomplete arch 32/64 compat from nft_compat. The original (bad)
idea was to probe the word size based on the xtables match/target info
size, but this assumption is wrong when you have to dump the information
back to userspace.
6) Allow to filter from prerouting and postrouting in the nf_tables bridge.
In order to emulate the ebtables NAT chains (which are actually simple
filter chains with no special semantics), we have support filtering from
this hooks too.
7) Add explicit module dependency between xt_physdev and br_netfilter.
This provides a way to detect if the user needs br_netfilter from
the configuration path. This should reduce the breakage of the
br_netfilter modularization.
8) Cleanup coding style in ip_vs.h, from Simon Horman.
9) Fix crash in the recently added nf_tables masq expression. We have
to register/unregister the notifiers to clean up the conntrack table
entries from the module init/exit path, not from the rule addition /
deletion path. From Arturo Borrero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when vlan filtering is turned on on the bridge, the bridge
will drop all traffic untill the user configures the filter. This
isn't very nice for ports that don't care about vlans and just
want untagged traffic.
A concept of a default_pvid was recently introduced. This patch
adds filtering support for default_pvid. Now, ports that don't
care about vlans and don't define there own filter will belong
to the VLAN of the default_pvid and continue to receive untagged
traffic.
This filtering can be disabled by setting default_pvid to 0.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if the pvid is not set, we return an illegal vlan value
even though the pvid value is set to 0. Since pvid of 0 is currently
invalid, just return 0 instead. This makes the current and future
checks simpler.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to set and retrieve default_pvid
value. A new value can only be stored when vlan filtering
is disabled.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
You can use physdev to match the physical interface enslaved to the
bridge device. This information is stored in skb->nf_bridge and it is
set up by br_netfilter. So, this is only available when iptables is
used from the bridge netfilter path.
Since 34666d4 ("netfilter: bridge: move br_netfilter out of the core"),
the br_netfilter code is modular. To reduce the impact of this change,
we can autoload the br_netfilter if the physdev match is used since
we assume that the users need br_netfilter in place.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This allows us to emulate the NAT table in ebtables, which is actually
a plain filter chain that hooks at prerouting, output and postrouting.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch introduces the NFT_REJECT_ICMPX_UNREACH type which provides
an abstraction to the ICMP and ICMPv6 codes that you can use from the
inet and bridge tables, they are:
* NFT_REJECT_ICMPX_NO_ROUTE: no route to host - network unreachable
* NFT_REJECT_ICMPX_PORT_UNREACH: port unreachable
* NFT_REJECT_ICMPX_HOST_UNREACH: host unreachable
* NFT_REJECT_ICMPX_ADMIN_PROHIBITED: administratevely prohibited
You can still use the specific codes when restricting the rule to match
the corresponding layer 3 protocol.
I decided to not overload the existing NFT_REJECT_ICMP_UNREACH to have
different semantics depending on the table family and to allow the user
to specify ICMP family specific codes if they restrict it to the
corresponding family.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In preparation for being able to propagate port states to e.g: notifiers
or other kernel parts, do not manipulate the port state directly, but
instead use a helper function which will allow us to do a bit more than
just setting the state.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric reports build failure with
CONFIG_BRIDGE_NETFILTER=n
We insist to build br_nf_core.o unconditionally, but we must only do so
if br_netfilter was enabled, else it fails to build due to
functions being defined to empty stubs (and some structure members
being defined out).
Also, BRIDGE_NETFILTER=y|m makes no sense when BRIDGE=n.
Fixes: 34666d467 (netfilter: bridge: move br_netfilter out of the core)
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
pull request: netfilter/ipvs updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
most relevantly they are:
1) Four patches to make the new nf_tables masquerading support
independent of the x_tables infrastructure. This also resolves a
compilation breakage if the masquerade target is disabled but the
nf_tables masq expression is enabled.
2) ipset updates via Jozsef Kadlecsik. This includes the addition of the
skbinfo extension that allows you to store packet metainformation in the
elements. This can be used to fetch and restore this to the packets through
the iptables SET target, patches from Anton Danilov.
3) Add the hash:mac set type to ipset, from Jozsef Kadlecsick.
4) Add simple weighted fail-over scheduler via Simon Horman. This provides
a fail-over IPVS scheduler (unlike existing load balancing schedulers).
Connections are directed to the appropriate server based solely on
highest weight value and server availability, patch from Kenny Mathis.
5) Support IPv6 real servers in IPv4 virtual-services and vice versa.
Simon Horman informs that the motivation for this is to allow more
flexibility in the choice of IP version offered by both virtual-servers
and real-servers as they no longer need to match: An IPv4 connection
from an end-user may be forwarded to a real-server using IPv6 and
vice versa. No ip_vs_sync support yet though. Patches from Alex Gartrell
and Julian Anastasov.
6) Add global generation ID to the nf_tables ruleset. When dumping from
several different object lists, we need a way to identify that an update
has ocurred so userspace knows that it needs to refresh its lists. This
also includes a new command to obtain the 32-bits generation ID. The
less significant 16-bits of this ID is also exposed through res_id field
in the nfnetlink header to quickly detect the interference and retry when
there is no risk of ID wraparound.
7) Move br_netfilter out of the bridge core. The br_netfilter code is
built in the bridge core by default. This causes problems of different
kind to people that don't want this: Jesper reported performance drop due
to the inconditional hook registration and I remember to have read complains
on netdev from people regarding the unexpected behaviour of our bridging
stack when br_netfilter is enabled (fragmentation handling, layer 3 and
upper inspection). People that still need this should easily undo the
damage by modprobing the new br_netfilter module.
8) Dump the set policy nf_tables that allows set parameterization. So
userspace can keep user-defined preferences when saving the ruleset.
From Arturo Borrero.
9) Use __seq_open_private() helper function to reduce boiler plate code
in x_tables, From Rob Jones.
10) Safer default behaviour in case that you forget to load the protocol
tracker. Daniel Borkmann and Florian Westphal detected that if your
ruleset is stateful, you allow traffic to at least one single SCTP port
and the SCTP protocol tracker is not loaded, then any SCTP traffic may
be pass through unfiltered. After this patch, the connection tracking
classifies SCTP/DCCP/UDPlite/GRE packets as invalid if your kernel has
been compiled with support for these modules.
====================
Trivially resolved conflict in include/linux/skbuff.h, Eric moved some
netfilter skbuff members around, and the netfilter tree adjusted the
ifdef guards for the bridging info pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper reported that br_netfilter always registers the hooks since
this is part of the bridge core. This harms performance for people that
don't need this.
This patch modularizes br_netfilter so it can be rmmod'ed, thus,
the hooks can be unregistered. I think the bridge netfilter should have
been a separated module since the beginning, Patrick agreed on that.
Note that this is breaking compatibility for users that expect that
bridge netfilter is going to be available after explicitly 'modprobe
bridge' or via automatic load through brctl.
However, the damage can be easily undone by modprobing br_netfilter.
The bridge core also spots a message to provide a clue to people that
didn't notice that this has been deprecated.
On top of that, the plan is that nftables will not rely on this software
layer, but integrate the connection tracking into the bridge layer to
enable stateful filtering and NAT, which is was bridge netfilter users
seem to require.
This patch still keeps the fake_dst_ops in the bridge core, since this
is required by when the bridge port is initialized. So we can safely
modprobe/rmmod br_netfilter anytime.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Florian Westphal <fw@strlen.de>
Move nf_bridge_copy_header() as static inline in netfilter_bridge.h
header file. This patch prepares the modularization of the br_netfilter
code.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
As Toshiaki Makita pointed out, the BRIDGE_INPUT_SKB_CB will
not be initialized in br_should_learn() as that function
is called only from br_handle_local_finish(). That is
an input handler for link-local ethernet traffic so it perfectly
correct to check br->vlan_enabled here.
Reported-by: Toshiaki Makita<toshiaki.makita1@gmail.com>
Fixes: 20adfa1 bridge: Check if vlan filtering is enabled only once.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, it is possible to modify the vlan filter
configuration to add pvid or untagged support.
For example:
bridge vlan add vid 10 dev eth0
bridge vlan add vid 10 dev eth0 untagged pvid
The second statement will modify vlan 10 to
include untagged and pvid configuration.
However, it is currently impossible to go backwards
bridge vlan add vid 10 dev eth0 untagged pvid
bridge vlan add vid 10 dev eth0
Here nothing happens. This patch correct this so
that any modifiers not supplied are removed from
the configuration.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge code checks if vlan filtering is enabled on both
ingress and egress. When the state flip happens, it
is possible for the bridge to currently be forwarding packets
and forwarding behavior becomes non-deterministic. Bridge
may drop packets on some interfaces, but not others.
This patch solves this by caching the filtered state of the
packet into skb_cb on ingress. The skb_cb is guaranteed to
not be over-written between the time packet entres bridge
forwarding path and the time it leaves it. On egress, we
can then check the cached state to see if we need to
apply filtering information.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
nf-next pull request
The following patchset contains Netfilter/IPVS updates for your
net-next tree. Regarding nf_tables, most updates focus on consolidating
the NAT infrastructure and adding support for masquerading. More
specifically, they are:
1) use __u8 instead of u_int8_t in arptables header, from
Mike Frysinger.
2) Add support to match by skb->pkttype to the meta expression, from
Ana Rey.
3) Add support to match by cpu to the meta expression, also from
Ana Rey.
4) A smatch warning about IPSET_ATTR_MARKMASK validation, patch from
Vytas Dauksa.
5) Fix netnet and netportnet hash types the range support for IPv4,
from Sergey Popovich.
6) Fix missing-field-initializer warnings resolved, from Mark Rustad.
7) Dan Carperter reported possible integer overflows in ipset, from
Jozsef Kadlecsick.
8) Filter out accounting objects in nfacct by type, so you can
selectively reset quotas, from Alexey Perevalov.
9) Move specific NAT IPv4 functions to the core so x_tables and
nf_tables can share the same NAT IPv4 engine.
10) Use the new NAT IPv4 functions from nft_chain_nat_ipv4.
11) Move specific NAT IPv6 functions to the core so x_tables and
nf_tables can share the same NAT IPv4 engine.
12) Use the new NAT IPv6 functions from nft_chain_nat_ipv6.
13) Refactor code to add nft_delrule(), which can be reused in the
enhancement of the NFT_MSG_DELTABLE to remove a table and its
content, from Arturo Borrero.
14) Add a helper function to unregister chain hooks, from
Arturo Borrero.
15) A cleanup to rename to nft_delrule_by_chain for consistency with
the new nft_*() functions, also from Arturo.
16) Add support to match devgroup to the meta expression, from Ana Rey.
17) Reduce stack usage for IPVS socket option, from Julian Anastasov.
18) Remove unnecessary textsearch state initialization in xt_string,
from Bojan Prtvar.
19) Add several helper functions to nf_tables, more work to prepare
the enhancement of NFT_MSG_DELTABLE, again from Arturo Borrero.
20) Enhance NFT_MSG_DELTABLE to delete a table and its content, from
Arturo Borrero.
21) Support NAT flags in the nat expression to indicate the flavour,
eg. random fully, from Arturo.
22) Add missing audit code to ebtables when replacing tables, from
Nicolas Dichtel.
23) Generalize the IPv4 masquerading code to allow its re-use from
nf_tables, from Arturo.
24) Generalize the IPv6 masquerading code, also from Arturo.
25) Add the new masq expression to support IPv4/IPv6 masquerading
from nf_tables, also from Arturo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes an unncessary check in the br_afspec() method of
br_netlink.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow rtnetlink users to set bridge master info via IFLA_INFO_DATA attr
This initial part implements forward_delay, hello_time, max_age options.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow rtnetlink users to get bridge master info in IFLA_INFO_DATA attr
This initial part implements forward_delay, hello_time, max_age options.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow rtnetlink users to set port info via IFLA_INFO_SLAVE_DATA attr
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow rtnetlink users to get port info in IFLA_INFO_SLAVE_DATA attr
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The thing is that netdev_master_upper_dev_link calls
call_netdevice_notifiers(NETDEV_CHANGEUPPER, dev). That generates rtnl
link message and during that, rtnl_link_ops->fill_slave_info is called.
But with current ordering, rx_handler and IFF_BRIDGE_PORT are not set
yet so there would have to be check for that in fill_slave_info callback.
Resolve this by reordering to similar what bonding and team does to
avoid the check.
Also add removal of IFF_BRIDGE_PORT flag into error path.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is already done for x_tables (family AF_INET and AF_INET6), let's
do it for AF_BRIDGE also.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel. When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets. This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.
There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver. These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb. When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.
The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued. The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294838888 ecr 0,nop,wscale 7], length 0
This connection finally times out.
I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver. There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.
The patch attempt to fix this another way. It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core. This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.
CC: Patrick McHardy <kaber@trash.net>
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet reports that getsockopt() or setsockopt() sometimes
returns -EINTR instead of -ENOPROTOOPT, causing headaches to
application developers.
This patch replaces all the mutex_lock_interruptible() by mutex_lock()
in the netfilter tree, as there is no reason we should sleep for a
long time there.
Reported-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now bridge ports can be non-promiscuous, vlan_vid_add() is no longer an
unnecessary operation.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 6cbdceeb1c
bridge: Dump vlan information from a bridge port
introduced a comment in an attempt to explain the
code logic. The comment is unfinished so it confuses more
than it explains, remove it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An FDB entry with vlan_id 0 doesn't mean it is used in vlan 0, but used when
vlan_filtering is disabled.
There is inconsistency around NDA_VLAN whose payload is 0 - even if we add
an entry by RTM_NEWNEIGH without any NDA_VLAN, and even though adding an
entry with NDA_VLAN 0 is prohibited, we get an entry with NDA_VLAN 0 by
RTM_GETNEIGH.
Dumping an FDB entry with vlan_id 0 shouldn't include NDA_VLAN.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ulog targets were recently killed. A few references to the Kconfig
macros CONFIG_IP_NF_TARGET_ULOG and CONFIG_BRIDGE_EBT_ULOG were left
untouched. Kill these too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
So you can reject IPv4 and IPv6 packets from bridge tables. If the ether
proto is now known, default on dropping the packet instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains updates for your net-next tree,
they are:
1) Use kvfree() helper function from x_tables, from Eric Dumazet.
2) Remove extra timer from the conntrack ecache extension, use a
workqueue instead to redeliver lost events to userspace instead,
from Florian Westphal.
3) Removal of the ulog targets for ebtables and iptables. The nflog
infrastructure superseded this almost 9 years ago, time to get rid
of this code.
4) Replace the list of loggers by an array now that we can only have
two possible non-overlapping logger flavours, ie. kernel ring buffer
and netlink logging.
5) Move Eric Dumazet's log buffer code to nf_log to reuse it from
all of the supported per-family loggers.
6) Consolidate nf_log_packet() as an unified interface for packet logging.
After this patch, if the struct nf_loginfo is available, it explicitly
selects the logger that is used.
7) Move ip and ip6 logging code from xt_LOG to the corresponding
per-family loggers. Thus, x_tables and nf_tables share the same code
for packet logging.
8) Add generic ARP packet logger, which is used by nf_tables. The
format aims to be consistent with the output of xt_LOG.
9) Add generic bridge packet logger. Again, this is used by nf_tables
and it routes the packets to the real family loggers. As a result,
we get consistent logging format for the bridge family. The ebt_log
logging code has been intentionally left in place not to break
backward compatibility since the logging output differs from xt_LOG.
10) Update nft_log to explicitly request the required family logger when
needed.
11) Finish nft_log so it supports arp, ip, ip6, bridge and inet families.
Allowing selection between netlink and kernel buffer ring logging.
12) Several fixes coming after the netfilter core logging changes spotted
by robots.
13) Use IS_ENABLED() macros whenever possible in the netfilter tree,
from Duan Jiong.
14) Removal of a couple of unnecessary branch before kfree, from Fabian
Frederick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually better than brctl showmacs because we can filter by bridge
port in the kernel.
The current bridge netlink interface doesnt scale when you have many
bridges each with large fdbs or even bridges with many bridge ports
And now for the science non-fiction novel you have all been
waiting for..
//lets see what bridge ports we have
root@moja-1:/configs/may30-iprt/bridge# ./bridge link show
8: eth1 state DOWN : <BROADCAST,MULTICAST> mtu 1500 master br0 state
disabled priority 32 cost 19
17: sw1-p1 state DOWN : <BROADCAST,NOARP> mtu 1500 master br0 state
disabled priority 32 cost 100
// show all..
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show
33:33:00:00:00:01 dev bond0 self permanent
33:33:00:00:00:01 dev dummy0 self permanent
33:33:00:00:00:01 dev ifb0 self permanent
33:33:00:00:00:01 dev ifb1 self permanent
33:33:00:00:00:01 dev eth0 self permanent
01:00:5e:00:00:01 dev eth0 self permanent
33:33:ff:22:01:01 dev eth0 self permanent
02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:07 dev eth1 self permanent
33:33:00:00:00:01 dev eth1 self permanent
33:33:00:00:00:01 dev gretap0 self permanent
da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent
33:33:00:00:00:01 dev sw1-p1 self permanent
//filter by bridge
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br br0
02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:07 dev eth1 self permanent
33:33:00:00:00:01 dev eth1 self permanent
da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent
33:33:00:00:00:01 dev sw1-p1 self permanent
// bridge sw1 has no ports attached..
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br sw1
//filter by port
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show brport eth1
02:00:00:12:01:02 vlan 0 master br0 permanent
00:17:42:8a:b4:05 vlan 0 master br0 permanent
00:17:42:8a:b4:07 self permanent
33:33:00:00:00:01 self permanent
// filter by port + bridge
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br br0 brport
sw1-p1
da:ac:46:27:d9:53 vlan 0 master br0 permanent
33:33:00:00:00:01 self permanent
// for shits and giggles (as they say in New Brunswick), lets
// change the mac that br0 uses
// Note: a magical fdb entry with no brport is added ...
root@moja-1:/configs/may30-iprt/bridge# ip link set dev br0 address
02:00:00:12:01:04
// lets see if we can see the unicorn ..
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show
33:33:00:00:00:01 dev bond0 self permanent
33:33:00:00:00:01 dev dummy0 self permanent
33:33:00:00:00:01 dev ifb0 self permanent
33:33:00:00:00:01 dev ifb1 self permanent
33:33:00:00:00:01 dev eth0 self permanent
01:00:5e:00:00:01 dev eth0 self permanent
33:33:ff:22:01:01 dev eth0 self permanent
02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:07 dev eth1 self permanent
33:33:00:00:00:01 dev eth1 self permanent
33:33:00:00:00:01 dev gretap0 self permanent
02:00:00:12:01:04 dev br0 vlan 0 master br0 permanent <=== there it is
da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent
33:33:00:00:00:01 dev sw1-p1 self permanent
//can we see it if we filter by bridge?
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br br0
02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:07 dev eth1 self permanent
33:33:00:00:00:01 dev eth1 self permanent
02:00:00:12:01:04 dev br0 vlan 0 master br0 permanent <=== there it is
da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent
33:33:00:00:00:01 dev sw1-p1 self permanent
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping a bridge fdb dumps every fdb entry
held. With this change we are going to filter
on selected bridge port.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch other modules are able to ask the bridge whether an
IGMP or MLD querier exists on the according, bridged link layer.
Multicast snooping can only be performed if a valid, selected querier
exists on a link.
Just like the bridge only enables its multicast snooping if a querier
exists, e.g. batman-adv too can only activate its multicast
snooping in bridged scenarios if a querier is present.
For instance this export avoids having to reimplement IGMP/MLD
querier message snooping and parsing in e.g. batman-adv, when
multicast optimizations for bridged scenarios are added in the
future.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the generic plain text packet loggger for bridged packets.
It routes the logging message to the real protocol packet logger.
I decided not to refactor the ebt_log code for two reasons:
1) The ebt_log output is not consistent with the IPv4 and IPv6
Netfilter packet loggers. The output is different for no good
reason and it adds redundant code to handle packet logging.
2) To avoid breaking backward compatibility for applications
outthere that are parsing the specific ebt_log output, the ebt_log
output has been left as is. So only nftables will use the new
consistent logging format for logged bridged packets.
More decisions coming in this patch:
1) This also removes ebt_log as default logger for bridged packets.
Thus, nf_log_packet() routes packet to this new packet logger
instead. This doesn't break backward compatibility since
nf_log_packet() is not used to log packets in plain text format
from anywhere in the ebtables/netfilter bridge code.
2) The new bridge packet logger also performs a lazy request to
register the real IPv4, ARP and IPv6 netfilter packet loggers.
If the real protocol logger is no available (not compiled or the
module is not available in the system, not packet logging happens.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that legacy ulog targets are not available anymore in the tree, we
can have up to two possible loggers:
1) The plain text logging via kernel logging ring.
2) The nfnetlink_log infrastructure which delivers log messages
to userspace.
This patch replaces the list of loggers by an array of two pointers
per family for each possible logger and it also introduces a new field
to the nf_logger structure which indicates the position in the logger
array (based on the logger type).
This prepares a follow up patch that consolidates the nf_log_packet()
interface by allowing to specify the logger as parameter.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This has been marked as deprecated for quite some time and the NFLOG
target replacement has been also available since 2006.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
use list_for_each_entry_continue_reverse to rollback in fdb_add_hw
when add address failed
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fields in "struct net_bridge" aren't available when compiling the
kernel without IPv6 support. Therefore adding a check/macro to skip the
complaining code sections in that case.
Introduced by 2cd4143192
("bridge: memorize and export selected IGMP/MLD querier port")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
"New smatch warnings:
net/bridge/br_multicast.c:1368 br_ip6_multicast_query() error:
we previously assumed 'group' could be null (see line 1349)"
In the rare (sort of broken) case of a query having a Maximum
Response Delay of zero, we could create a potential null pointer
dereference.
Fixing this by skipping the multicast specific MLD Query parsing again
if no multicast group address is available.
Introduced by dc4eb53a99
("bridge: adhere to querier election mechanism specified by RFCs")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables us to change the vlan protocol for vlan filtering.
We come to be able to filter frames on the basis of 802.1ad vlan tags
through a bridge.
This also changes br->group_addr if it has not been set by user.
This is needed for an 802.1ad bridge.
(See IEEE 802.1Q-2011 8.13.5.)
Furthermore, this sets br->group_fwd_mask_required so that an 802.1ad
bridge can forward the Nearest Customer Bridge group addresses except
for br->group_addr, which should be passed to higher layer.
To change the vlan protocol, write a protocol in sysfs:
# echo 0x88a8 > /sys/class/net/br0/bridge/vlan_protocol
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bridge is an 802.1ad bridge, it must forward another bridge group
addresses (the Nearest Customer Bridge group addresses).
(For details, see IEEE 802.1Q-2011 8.6.3.)
As user might not want group_fwd_mask to be modified by enabling 802.1ad,
introduce a new mask, group_fwd_mask_required, which indicates addresses
the bridge wants to forward. This will be set by enabling 802.1ad.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables a bridge to have vlan protocol informantion and allows vlan
tag manipulation (retrieve, insert and remove tags) according to the vlan
protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge device doesn't need to embed S-tag into skb->data.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding bridge support to the batman-adv multicast optimization requires
batman-adv knowing about the existence of bridged-in IGMP/MLD queriers
to be able to reliably serve any multicast listener behind this same
bridge.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this new, exported function br_multicast_list_adjacent(net_dev) a
list of IPv4/6 addresses is returned. This list contains all multicast
addresses sensed by the bridge multicast snooping feature on all bridge
ports of the bridge interface of net_dev, excluding addresses from the
specified net_device itself.
Adding bridge support to the batman-adv multicast optimization requires
batman-adv knowing about the existence of bridged-in multicast
listeners to be able to reliably serve them with multicast packets.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko