The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If firmware controls DPC, it is generally responsible for managing the DPC
capability and events, and the OS should not access the DPC capability.
However, if firmware controls DPC and both the OS and the platform support
Error Disconnect Recover (EDR) notifications, the OS EDR notify handler is
responsible for recovery, and the notify handler may read/write the DPC
capability until it clears the DPC Trigger Status bit. See [1], sec 4.5.1,
table 4-6.
Expose some DPC error handling functions so they can be used by the EDR
notify handler.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
Link: https://lore.kernel.org/r/e9000bb15b3a4293e81d98bb29ead7c84a6393c9.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per the SFI _OSC and DPC Updates ECN [1] implementation note flowchart, the
OS seems to be expected to clear AER status even if it doesn't have
ownership of the AER capability. Unlike the DPC capability, where a DPC
ECN [2] specifies a window when the OS is allowed to access DPC registers
even if it doesn't have ownership, there is no clear model for AER.
Add pci_aer_raw_clear_status() to clear the AER error status registers
unconditionally. This is intended for use only by the EDR path (see [2]).
[1] System Firmware Intermediary (SFI) _OSC and DPC Updates ECN, Feb 24,
2020, affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/14076
[2] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
[bhelgaas: changelog]
Link: https://lore.kernel.org/r/c19ad28f3633cce67448609e89a75635da0da07d.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As per the DPC Enhancements ECN [1], sec 4.5.1, table 4-4, if the OS
supports Error Disconnect Recover (EDR), it must invalidate the software
state associated with child devices of the port without attempting to
access the child device hardware. In addition, if the OS supports DPC, it
must attempt to recover the child devices if the port implements the DPC
Capability. If the OS continues operation, the OS must inform the firmware
of the status of the recovery operation via the _OST method.
Return the result of pcie_do_recovery() so we can report it to firmware via
_OST.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
Link: https://lore.kernel.org/r/eb60ec89448769349c6722954ffbf2de163155b5.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we passed the PCIe service type parameter to pcie_do_recovery(),
where reset_link() looked up the underlying pci_port_service_driver and its
.reset_link() function pointer. Instead of using this roundabout way, we
can just pass the driver-specific .reset_link() callback function when
calling pcie_do_recovery() function.
This allows us to call pcie_do_recovery() from code that is not a PCIe port
service driver, e.g., Error Disconnect Recover (EDR) support.
Remove pcie_port_find_service() and pcie_port_service_driver.reset_link
since they are now unused.
Link: https://lore.kernel.org/r/60e02b87b526cdf2930400059d98704bf0a147d1.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add PCIE_LNKCAP2_SLS2SPEED macro for transforming raw Link Capabilities 2
values to the pci_bus_speed. This is next to PCIE_SPEED2MBS_ENC() to make
it easier to update both places when adding support for new speeds.
Link: https://lore.kernel.org/r/1581937984-40353-10-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously some PCI speed strings came from pci_speed_string(), some came
from the PCIe-specific PCIE_SPEED2STR(), and some came from a PCIe-specific
switch statement. These methods were inconsistent:
pci_speed_string() PCIE_SPEED2STR() switch
------------------ ---------------- ------
33 MHz PCI
...
2.5 GT/s PCIe 2.5 GT/s 2.5 GT/s
5.0 GT/s PCIe 5 GT/s 5 GT/s
8.0 GT/s PCIe 8 GT/s 8 GT/s
16.0 GT/s PCIe 16 GT/s 16 GT/s
32.0 GT/s PCIe 32 GT/s 32 GT/s
Standardize on pci_speed_string() as the single source of these strings.
Note that this adds ".0" and "PCIe" to some messages, including sysfs
"max_link_speed" files, a brcmstb "link up" message, and the link status
dmesg logging, e.g.,
nvme 0000:01:00.0: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:01.1 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
I think it's better to standardize on a single version of the speed text.
Previously we had strings like this:
/sys/bus/pci/slots/0/cur_bus_speed: 8.0 GT/s PCIe
/sys/bus/pci/slots/0/max_bus_speed: 8.0 GT/s PCIe
/sys/devices/pci0000:00/0000:00:1c.0/current_link_speed: 8 GT/s
/sys/devices/pci0000:00/0000:00:1c.0/max_link_speed: 8 GT/s
This changes the latter two to match the slots files:
/sys/devices/pci0000:00/0000:00:1c.0/current_link_speed: 8.0 GT/s PCIe
/sys/devices/pci0000:00/0000:00:1c.0/max_link_speed: 8.0 GT/s PCIe
Based-on-patch by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pci_speed_string() to return a text description of the supplied bus or
link speed. The slot code previously used the private
pci_bus_speed_strings[] array for this purpose, but adding this interface
will enable us to consolidate similar code elsewhere.
Export pcie_link_speed[] and pci_speed_string() so they can be used by
modules.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link speed 32.0 GT/s is supported in PCIe r5.0. Add this speed to
PCIE_SPEED2STR() and PCIE_SPEED2MBS_ENC() to correctly decode it.
This is complementary to de76cda215 ("PCI: Decode PCIe 32 GT/s link
speed").
Link: https://lore.kernel.org/r/1581937984-40353-2-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The number of possible devfns is 256, but pci_add_dma_alias() allocated a
bitmap of size 255. Fix this off-by-one error.
This fixes commits 338c3149a2 ("PCI: Add support for multiple DMA
aliases") and c663579273 ("PCI: Allocate dma_alias_mask with
bitmap_zalloc()"), but I doubt it was possible to see a problem because
it takes 4 64-bit longs (or 8 32-bit longs) to hold 255 bits, and
bitmap_zalloc() doesn't save the 255-bit size anywhere.
[bhelgaas: commit log, move #define to drivers/pci/pci.h, include loop
limit fix from Qian Cai:
https://lore.kernel.org/r/20191218170004.5297-1-cai@lca.pw]
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
- Consolidate DT "dma-ranges" parsing and convert all host drivers to use
shared parsing (Rob Herring)
* remotes/lorenzo/pci/mmio-dma-ranges:
PCI: Make devm_of_pci_get_host_bridge_resources() static
PCI: rcar: Use inbound resources for setup
PCI: iproc: Use inbound resources for setup
PCI: xgene: Use inbound resources for setup
PCI: v3-semi: Use inbound resources for setup
PCI: ftpci100: Use inbound resources for setup
PCI: of: Add inbound resource parsing to helpers
PCI: versatile: Enable COMPILE_TEST
PCI: versatile: Remove usage of PHYS_OFFSET
PCI: versatile: Use pci_parse_request_of_pci_ranges()
PCI: xilinx-nwl: Use pci_parse_request_of_pci_ranges()
PCI: xilinx: Use pci_parse_request_of_pci_ranges()
PCI: xgene: Use pci_parse_request_of_pci_ranges()
PCI: v3-semi: Use pci_parse_request_of_pci_ranges()
PCI: rockchip: Drop storing driver private outbound resource data
PCI: rockchip: Use pci_parse_request_of_pci_ranges()
PCI: mobiveil: Use pci_parse_request_of_pci_ranges()
PCI: mediatek: Use pci_parse_request_of_pci_ranges()
PCI: iproc: Use pci_parse_request_of_pci_ranges()
PCI: faraday: Use pci_parse_request_of_pci_ranges()
PCI: dwc: Use pci_parse_request_of_pci_ranges()
PCI: altera: Use pci_parse_request_of_pci_ranges()
PCI: aardvark: Use pci_parse_request_of_pci_ranges()
PCI: Export pci_parse_request_of_pci_ranges()
resource: Add a resource_list_first_type helper
# Conflicts:
# drivers/pci/controller/pcie-rcar.c
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the VFs,
but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and associated
VFs can be enabled independently (Kuppuswamy Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn Helgaas)
- Hide PRI and PASID state restoration functions used only inside the PCI
core (Bjorn Helgaas)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George Cherian)
- Unify ACS quirk implementations (Bjorn Helgaas)
* pci/virtualization:
PCI: Unify ACS quirk desired vs provided checking
PCI: Make ACS quirk implementations more uniform
PCI: Apply Cavium ACS quirk to ThunderX2 and ThunderX3
PCI/IOV: Serialize sysfs sriov_numvfs reads vs writes
PCI: Add DMA alias quirk for Intel VCA NTB
PCI: Fix Intel ACS quirk UPDCR register address
PCI/ATS: Make pci_restore_pri_state(), pci_restore_pasid_state() private
PCI/ATS: Remove unnecessary EXPORT_SYMBOL_GPL()
PCI/ATS: Remove unused PRI and PASID stubs
PCI/ATS: Consolidate ATS declarations in linux/pci-ats.h
PCI/ATS: Cache PRI PRG Response PASID Required bit
PCI/ATS: Cache PASID Capability offset
PCI/ATS: Cache PRI Capability offset
PCI/ATS: Disable PF/VF ATS service independently
PCI/ATS: Handle sharing of PF PASID Capability with all VFs
PCI/ATS: Handle sharing of PF PRI Capability with all VFs
PCI/ATS: Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI
iommu/vt-d: Select PCI_PRI for INTEL_IOMMU_SVM
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we only
did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0) instead
of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
* pci/pm:
PCI/PM: Move pci_dev_wait() definition earlier
PCI/PM: Add missing link delays required by the PCIe spec
PCI/PM: Add pcie_wait_for_link_delay()
PCI/PM: Return error when changing power state from D3cold
PCI/PM: Decode D3cold power state correctly
PCI/PM: Fold __pci_complete_power_transition() into its caller
PCI/PM: Avoid exporting __pci_complete_power_transition()
PCI/PM: Fold __pci_start_power_transition() into its caller
PCI/PM: Use pci_power_up() in pci_set_power_state()
PCI/PM: Move power state update away from pci_power_up()
PCI/PM: Remove unused pci_driver.suspend_late() hook
PCI/PM: Remove unused pci_driver.resume_early() hook
xen-platform: Convert to generic power management
PCI/PM: Simplify pci_set_power_state()
PCI/PM: Expand PM reset messages to mention D3hot (not just D3)
PCI/PM: Apply D2 delay as milliseconds, not microseconds
PCI/PM: Use pci_WARN() to include device information
PCI/PM: Use PCI dev_printk() wrappers for consistency
PCI/PM: Wrap long lines in documentation
PCI/PM: Note that PME can be generated from D0
PCI/PM: Make power management op coding style consistent
PCI/PM: Run resume fixups before disabling wakeup events
PCI/PM: Clear PCIe PME Status even for legacy power management
PCI/PM: Correct pci_pm_thaw_noirq() documentation
PCI/PM: Always return devices to D0 when thawing
Previously, CONFIG_PCIEASPM_DEBUG enabled "link_state" and "clk_ctl" sysfs
files that controlled ASPM. We believe these files were rarely if ever
used.
We recently added sysfs ASPM controls that are always present, so the debug
code is no longer needed. Removing this debug code has been discussed for
quite some time, see e.g. [0].
Remove PCIEASPM_DEBUG and the related code.
[0] https://lore.kernel.org/lkml/20180727202619.GD173328@bhelgaas-glaptop.roam.corp.google.com/
Link: https://lore.kernel.org/r/ec935d8e-c084-3938-f1d1-748617596b25@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes to Endpoints and other Upstream Ports to control ASPM,
Clock PM, and L1 PM Substates. The new attributes are:
/sys/devices/pci*/.../link/clkpm
/sys/devices/pci*/.../link/l0s_aspm
/sys/devices/pci*/.../link/l1_aspm
/sys/devices/pci*/.../link/l1_1_aspm
/sys/devices/pci*/.../link/l1_2_aspm
/sys/devices/pci*/.../link/l1_1_pcipm
/sys/devices/pci*/.../link/l1_2_pcipm
An attribute is only visible if both ends of the Link leading to the device
support the state. Writing y/1/on to the file enables the state; n/0/off
disables it.
These attributes can be used to tune the power/performance tradeoff for
individual devices.
[bhelgaas: commit log, rename directory to "link"]
Link: https://lore.kernel.org/r/b1c83f8a-9bf6-eac5-82d0-cf5b90128fbf@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently Linux does not follow PCIe spec regarding the required delays
after reset. A concrete example is a Thunderbolt add-in-card that consists
of a PCIe switch and two PCIe endpoints:
+-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
+-01.0-[04-36]-- DS hotplug port
+-02.0-[37]----00.0 xHCI controller
\-04.0-[38-6b]-- DS hotplug port
The root port (1b.0) and the PCIe switch downstream ports are all PCIe Gen3
so they support 8GT/s link speeds.
We wait for the PCIe hierarchy to enter D3cold (runtime):
pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
When it wakes up from D3cold, according to the PCIe 5.0 section 5.8 the
PCIe switch is put to reset and its power is re-applied. This means that we
must follow the rules in PCIe 5.0 section 6.6.1.
For the PCIe Gen3 ports we are dealing with here, the following applies:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Translating this into the above topology we would need to do this (DLLLA
stands for Data Link Layer Link Active):
0000:00:1b.0: wait for 100 ms after DLLLA is set before access to 0000:01:00.0
0000:02:00.0: wait for 100 ms after DLLLA is set before access to 0000:03:00.0
0000:02:02.0: wait for 100 ms after DLLLA is set before access to 0000:37:00.0
I've instrumented the kernel with some additional logging so we can see the
actual delays performed:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
For the switch upstream port (01:00.0 reachable through 00:1b.0 root port)
we wait for 100 ms but not taking into account the DLLLA requirement. We
then wait 10 ms for D3hot -> D0 transition of the root port and the two
downstream hotplug ports. This means that we deviate from what the spec
requires.
Performing the same check for system sleep (s2idle) transitions it turns
out to be even worse. None of the mandatory delays are performed. If this
would be S3 instead of s2idle then according to PCI FW spec 3.2 section
4.6.8. there is a specific _DSM that allows the OS to skip the delays but
this platform does not provide the _DSM and does not go to S3 anyway so no
firmware is involved that could already handle these delays.
On this particular platform these delays are not actually needed because
there is an additional delay as part of the ACPI power resource that is
used to turn on power to the hierarchy but since that additional delay is
not required by any of standards (PCIe, ACPI) it is not present in the
Intel Ice Lake, for example where missing the mandatory delays causes
pciehp to start tearing down the stack too early (links are not yet
trained). Below is an example how it looks like when this happens:
pcieport 0000:83:04.0: pciehp: Slot(4): Card not present
pcieport 0000:87:04.0: PME# disabled
pcieport 0000:83:04.0: pciehp: pciehp_unconfigure_device: domain🚌dev = 0000:86:00
pcieport 0000:86:00.0: Refused to change power state, currently in D3
pcieport 0000:86:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x201ff)
pcieport 0000:86:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
There is also one reported case (see the bugzilla link below) where the
missing delay causes xHCI on a Titan Ridge controller fail to runtime
resume when USB-C dock is plugged. This does not involve pciehp but instead
the PCI core fails to runtime resume the xHCI device:
pcieport 0000:04:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:04:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100406)
xhci_hcd 0000:39:00.0: Refused to change power state, currently in D3
xhci_hcd 0000:39:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x1ff)
xhci_hcd 0000:39:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
Add a new function pci_bridge_wait_for_secondary_bus() that is called on
PCI core resume and runtime resume paths accordingly if the bridge entered
D3cold (and thus went through reset).
This is second attempt to add the missing delays. The previous solution in
c2bf1fc212 ("PCI: Add missing link delays required by the PCIe spec") was
reverted because of two issues it caused:
1. One system become unresponsive after S3 resume due to PME service
spinning in pcie_pme_work_fn(). The root port in question reports that
the xHCI sent PME but the xHCI device itself does not have PME status
set. The PME status bit is never cleared in the root port resulting
the indefinite loop in pcie_pme_work_fn().
2. Slows down resume if the root/downstream port does not support Data
Link Layer Active Reporting because pcie_wait_for_link_delay() waits
1100 ms in that case.
This version should avoid the above issues because we restrict the delay to
happen only if the port went into D3cold.
Link: https://lore.kernel.org/linux-pci/SL2P216MB01878BBCD75F21D882AEEA2880C60@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM/
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203885
Link: https://lore.kernel.org/r/20191112091617.70282-3-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make it explicitly clear that the code to put devices into D0 in
pci_set_power_state() and in pci_pm_default_resume_early() is the
same by making the latter use pci_power_up() for transitions into D0.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/2520019.OZ1nXS5aSj@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that all the PCI host drivers are using pci_parse_request_of_pci_ranges(),
make devm_of_pci_get_host_bridge_resources() static.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Extend devm_of_pci_get_host_bridge_resources() and
pci_parse_request_of_pci_ranges() helpers to also parse the inbound
addresses from DT 'dma-ranges' and populate a resource list with the
translated addresses. This will help ensure 'dma-ranges' is always
parsed in a consistent way.
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> # for AArdvark
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Will Deacon <will@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: rfi@lists.rocketboards.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
The existing "pci=hpmemsize=nn[KMG]" kernel parameter overrides the default
size of both the non-prefetchable and the prefetchable MMIO windows for
hotplug bridges.
Add "pci=hpmmiosize=nn[KMG]" to override the default size of only the
non-prefetchable MMIO window.
Add "pci=hpmmioprefsize=nn[KMG]" to override the default size of only the
prefetchable MMIO window.
Link: https://lore.kernel.org/r/SL2P216MB0187E4D0055791957B7E2660806B0@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Previously we did not save and restore the AER configuration on
suspend/resume, so the configuration may be lost after resume.
Save the AER configuration during suspend and restore it during resume.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/92EBB4272BF81E4089A7126EC1E7B28492C3B007@IRSMSX101.ger.corp.intel.com
Signed-off-by: Mayurkumar Patel <mayurkumar.patel@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
These interfaces:
void pci_restore_pri_state(struct pci_dev *pdev);
void pci_restore_pasid_state(struct pci_dev *pdev);
are only used in drivers/pci and do not need to be seen by the rest of the
kernel. Most them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
- Use devm_add_action_or_reset() helper (Fuqian Huang)
- Mark expected switch fall-through (Gustavo A. R. Silva)
- Convert sysfs device attributes from __ATTR() to DEVICE_ATTR() (Kelsey
Skunberg)
- Convert sysfs file permissions from S_IRUSR etc to octal (Kelsey
Skunberg)
- Move SR-IOV sysfs functions to iov.c (Kelsey Skunberg)
- Add pci_info_ratelimited() to ratelimit PCI messages separately
(Krzysztof Wilczynski)
- Fix "'static' not at beginning of declaration" warnings (Krzysztof
Wilczynski)
- Clean up resource_alignment parameter to not require static buffer
(Logan Gunthorpe)
- Add ACS quirk for iProc PAXB (Abhinav Ratna)
- Add pci_irq_vector() and other stubs for !CONFIG_PCI (Herbert Xu)
* pci/misc:
PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI
PCI: Add ACS quirk for iProc PAXB
PCI: Force trailing new line to resource_alignment_param in sysfs
PCI: Move pci_[get|set]_resource_alignment_param() into their callers
PCI: Clean up resource_alignment parameter to not require static buffer
PCI: Use static const struct, not const static struct
PCI: Add pci_info_ratelimited() to ratelimit PCI separately
PCI/IOV: Remove group write permission from sriov_numvfs, sriov_drivers_autoprobe
PCI/IOV: Move sysfs SR-IOV functions to iov.c
PCI: sysfs: Change permissions from symbolic to octal
PCI: sysfs: Change DEVICE_ATTR() to DEVICE_ATTR_WO()
PCI: sysfs: Define device attributes with DEVICE_ATTR*()
PCI: Mark expected switch fall-through
PCI: Use devm_add_action_or_reset()
- Consolidate _HPP & _HPX code in pci-acpi.h and remove unnecessary
struct hotplug_program_ops (Krzysztof Wilczynski)
- Fixup PCIe device types to remove the need for dev->has_secondary_link
(Mika Westerberg)
* pci/enumeration:
PCI: Get rid of dev->has_secondary_link flag
PCI: Make pcie_downstream_port() available outside of access.c
PCI/ACPI: Remove unnecessary struct hotplug_program_ops
PCI/ACPI: Move _HPP & _HPX functions to pci-acpi.c
PCI/ACPI: Rename _HPX structs from hpp_* to hpx_*
pcie_downstream_port() is useful in other places where code needs to
determine whether the PCIe port is downstream so make it available outside
of access.c.
Link: https://lore.kernel.org/r/20190822085553.62697-1-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Move the ACPI-specific structs hpx_type0, hpx_type1, hpx_type2 and
hpx_type3 to drivers/pci/pci-acpi.c as they are not used anywhere else.
Then remove the struct hotplug_program_ops that has been shared between
drivers/pci/probe.c and drivers/pci/pci-acpi.c from drivers/pci/pci.h as it
is no longer needed.
The struct hotplug_program_ops was added by 87fcf12e84 ("PCI/ACPI: Remove
the need for 'struct hotplug_params'") and replaced previously used struct
hotplug_params enabling the support for the _HPX Type 3 Setting Record that
was added by f873c51a15 ("PCI/ACPI: Implement _HPX Type 3 Setting
Record").
The new struct allowed for the static functions such program_hpx_type0(),
program_hpx_type1(), etc., from the drivers/pci/probe.c to be called from
the function pci_acpi_program_hp_params() in the drivers/pci/pci-acpi.c.
Previously a programming of _HPX Type 0 was as follows:
drivers/pci/probe.c:
program_hpx_type0()
...
pci_configure_device()
hp_ops = {
.program_type0 = program_hpx_type0,
...
}
pci_acpi_program_hp_params(&hp_ops)
drivers/pci/pci-acpi.c:
pci_acpi_program_hp_params(&hp_ops)
acpi_run_hpx(hp_ops)
decode_type0_hpx_record()
hp_ops->program_type0 # program_hpx_type0() called via hp_ops
After the ACPI-specific functions, structs, enums, etc., have been moved to
drivers/pci/pci-acpi.c there is no need for the hotplug_program_ops as all
of the _HPX Type 0, 1, 2 and 3 are directly accessible.
Link: https://lore.kernel.org/r/20190827094951.10613-4-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move program_hpx_type0(), program_hpx_type1(), etc., and enums
hpx_type3_dev_type, hpx_type3_fn_type and hpx_type3_cfg_loc to
drivers/pci/pci-acpi.c as these functions and enums are ACPI-specific.
Move structs hpx_type0, hpx_type1, hpx_type2 and hpx_type3 to
drivers/pci/pci.h as these are shared between drivers/pci/pci-acpi.c and
drivers/pci/probe.c.
Link: https://lore.kernel.org/r/20190827094951.10613-3-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sysfs SR-IOV functions are only needed when the kernel is built with
SR-IOV support. Rather than put them in pci-sysfs.c under #ifdef
CONFIG_PCI_IOV, move them to iov.c, which is only compiled when
CONFIG_PCI_IOV=y.
Link: https://lore.kernel.org/r/20190813204513.4790-4-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Donald Dutile <ddutile@redhat.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
These interfaces:
void pci_set_of_node(struct pci_dev *dev);
void pci_release_of_node(struct pci_dev *dev);
void pci_set_bus_of_node(struct pci_bus *bus);
void pci_release_bus_of_node(struct pci_bus *bus);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-12-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This interface:
int pci_enable_ptm(struct pci_dev *dev, u8 *granularity);
is only used in drivers/pci/ and does not need to be seen by the rest of
the kernel. Move it to drivers/pci/pci.h so it's private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-11-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
void pcie_set_ecrc_checking(struct pci_dev *dev);
void pcie_ecrc_get_policy(char *str);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-10-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This interface:
void pci_ats_init(struct pci_dev *dev);
is only used in drivers/pci/ and does not need to be seen by the rest of
the kernel. Move it to drivers/pci/pci.h so it's private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-9-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This interface:
void pcie_update_link_speed(struct pci_bus *bus, u16 link_status);
is only used in drivers/pci/ and does not need to be seen by the rest of
the kernel. Move it to drivers/pci/pci.h so it's private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-8-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
struct pci_bus *pci_bus_get(struct pci_bus *bus);
void pci_bus_put(struct pci_bus *bus);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-7-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These symbols:
extern unsigned long pci_hotplug_io_size;
extern unsigned long pci_hotplug_mem_size;
extern unsigned long pci_hotplug_bus_size;
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-6-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These Virtual Channel interfaces:
int pci_save_vc_state(struct pci_dev *dev);
void pci_restore_vc_state(struct pci_dev *dev);
void pci_allocate_vc_save_buffers(struct pci_dev *dev);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-5-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
struct device *pci_get_host_bridge_device(struct pci_dev *dev);
void pci_put_host_bridge_device(struct device *dev);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-4-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
bool pci_check_pme_status(struct pci_dev *dev);
void pci_pme_wakeup_bus(struct pci_bus *bus);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-3-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These delay time definitions:
#define PCI_PM_D2_DELAY 200
#define PCI_PM_D3_WAIT 10
#define PCI_PM_D3COLD_WAIT 100
#define PCI_PM_BUS_WAIT 50
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-2-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Revert 975bb8b4dc ("PCI/IOV: Use VF0 cached config space size for other
VFs"), which attempted to cache the config space size from the first VF to
re-use for subsequent VFs.
The cached value was determined prior to discovering the PCIe capability on
the VF, which resulted in the first VF reporting the correct config space
size (4K), as it has a special case through pci_cfg_space_size(), while all
the other VFs only reported 256 bytes. As this was only a performance
optimization, we're better off without it.
Fixes: 975bb8b4dc ("PCI/IOV: Use VF0 cached config space size for other VFs")
Link: https://lore.kernel.org/r/156046663197.29869.3633634445109057665.stgit@gimli.home
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Hao Zheng <yinhe@linux.alibaba.com>
In pci_pm_complete() there are checks to decide whether or not to
resume devices that were left in runtime-suspend during the preceding
system-wide transition into a sleep state. They involve checking the
current power state of the device and comparing it with the power
state of it set before the preceding system-wide transition, but the
platform component of the device's power state is not handled
correctly in there.
Namely, on platforms with ACPI, the device power state information
needs to be updated with care, so that the reference counters of
power resources used by the device (if any) are set to ensure that
the refreshed power state of it will be maintained going forward.
To that end, introduce a new ->refresh_state() platform PM callback
for PCI devices, for asking the platform to refresh the device power
state data and ensure that the corresponding power state will be
maintained going forward, make it invoke acpi_device_update_power()
(for devices with ACPI PM) on platforms with ACPI and make
pci_pm_complete() use it, through a new pci_refresh_power_state()
wrapper function.
Fixes: a0d2a959d3 (PCI: Avoid unnecessary resume after direct-complete)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Bjorn Helgaas