We've tried several times to make this machine 'just work', but every
patch that does causes many other machines to fail. This adds a quirk
which special cases this hardware and forces ssc to be
disabled. There's no way to override this from the command line; that
would be a significantly more invasive change.
This patch fixes#36656 on fdo bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=36656
Signed-off-by: Keith Packard <keithp@keithp.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36656
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Upon review, all path share the same dependencies for updating the
registers and so we can benefit from sharing the code and checking
early.
This removes the unsightly intel_wait_for_vblank() from the lowlevel
functions and upon further analysis the only path that will require a
wait is if we are performing an instantaneous transition between two
valid FBC configurations. The page-flip path itself will have disabled
FBC registers and will have waited for at least one vblank before
finishing the flip and attempting to re-enable FBC. This wait can be
accomplished simply by delaying the enable until after we are sure that
a vblank will have passed, which we are already doing to make sure that
the display is settled before enabling FBC.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
In order to accommodate the requirements of re-enabling FBC after
page-flipping, but to avoid doing so and incurring the cost of a wait
for vblank in the middle of a page-flip sequence, we defer the actual
enablement by 50ms. If any request to disable FBC arrive within that
interval, the enablement is cancelled and we are saved from blocking on
the wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Page-flipping updates the scanout address, nukes the FBC compressed
image and so forces an FBC update so that the displayed image remains
consistent. However, page-flipping does not update the FBC registers
themselves, which remain pointing to both the old address and the old
CPU fence. Future updates to the new front-buffer (scanout) are then
undetected!
This first approach to demonstrate the issue and highlight the fix,
simply disables FBC upon page-flip (a recompression will be forced on
every flip so FBC becomes immaterial) and then re-enables FBC in the
page-flip finish work function, so that the FBC registers are now
pointing to the new framebuffer and front-buffer rendering works once
more.
Ideally, we want to only re-enable FBC after page-flipping is complete,
as otherwise we are just wasting cycles and power (with needless
recompression) whilst the page-flipping application is still running.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33487
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Persistent mode is intended for use with front-buffer rendering, such as
X, where it is necessary to detect writes to the scanout either by the
GPU or through the CPU's fence, and recompress the dirty regions on the
fly. (By comparison to the back-buffer rendering, the scanout is always
recompressed after a page-flip.)
References: https://bugs.freedesktop.org/show_bug.cgi?id=33487
References: https://bugs.freedesktop.org/show_bug.cgi?id=31742
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
...and this requirement is enforced by intel_update_fbc() so we can
remove the later check from g4x_enable_fbc() and ironlake_enable_fbc().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The cfb_pitch was only used for 8xx_enable_fbc(), every later routine
was just overwriting the value with itself thanks to a copy'n'paste
error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
...to ensure that any pending FBC enable tasklet is cancelled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As the enable/disable routines will be gain additional complexity in
future patches, it is necessary that all callers do not bypass the
generic interface by calling into the chipset routines directly. to do
this we make the chipset routines static, so there is no choice.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This will catch bad fb configs earlier.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Updating the planes is device specific, so create a new display callback
and use it in pipe_set_base. (In fact we could go even further, valid
display plane bits have changed with each generation, as has tiled
buffer handling.)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Figuring out which pipe bpp to use is a bit painful. It depends on both
the encoder and display configuration attached to a pipe. For instance,
to drive a 24bpp framebuffer out to an 18bpp panel, we need to use 6bpc
on the pipe but also enable dithering. But driving that same
framebuffer to a DisplayPort output on another pipe means using 8bpc and
no dithering.
So split out and enhance the code to handle the various cases, returning
an appropriate pipe bpp as well as whether dithering should be enabled.
Save the resulting pipe bpp in the intel_crtc struct for use by encoders
in calculating bandwidth requirements (defaults to 24bpp on pre-ILK).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This may not be the default value, so pull the bpc out of the pipe reg
and write it to the DP transcoder so proper dithering and signaling
occurs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This prevents us from setting reserved or incorrect bits on CougarPoint.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
They use the same register interfaces, so we can simply enable the
existing code on IVB.
v2:
- resolve conflict with ring freq scaling, we can enable it too
v3:
- resolve conflict again, this time on drm-intel-next
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The ring frequency scaling table tells the PCU to treat certain GPU
frequencies as if they were a given CPU frequency for purposes of
scaling the ring frequency. Normally the PCU will scale the ring
frequency based on the CPU P-state, but with the table present, it will
also take the GPU frequency into account.
The main downside of keeping the ring frequency high while the CPU is
at a low frequency (or asleep altogether) is increased power
consumption. But then if you're keeping your GPU busy, you probably
want the extra performance.
v2:
- add units to debug table header (from Eric)
- use tsc_khz as a fallback if the cpufreq driver doesn't give us a freq
(from Chris)
v3:
- fix comments & debug output
- remove unneeded force wake get/put
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This makes things a little clearer and prevents us from running old code
on a new chipset that may not be supported.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewied-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
We need to perform a few operations in order to move the object into the
display plane (where it can be accessed coherently by the display
engine) that are important for future safety to forbid whilst pinned. As a
result, we want to need to perform some of the operations before pinning,
but some are required once we have been bound into the GTT. So combine
the pinning performed by all the callers with set_to_display_plane(), so
this complication is contained within the single function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... reincarnated from i915_gem_object_flush_gpu(). The semantic
difference is that after calling finish_gpu() the object no longer
resides in any GPU domain, and so will cause the GPU caches to be
invalidated if it is ever used again.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The computation of the first-level watermarks for g4x and gen5+ are
based on the same algorithm, so we can refactor those code paths to
use a single function.
Note that g4x_compute_wm0 takes a 'plane' argument while
ironlake_compute_wm0 took a 'pipe' argument. Both should have used a
'plane' argument, so this patch fixes that as well (not that it caused
a problem; ironlake always uses pipe == plane).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
During the refactoring in revision 6067aaeadb,
the intel_enable_clock_gating was split up into several functions that are
then called indirectly. However, which function to call was not specified for
the IS_PINEVIEW() case. This patch specifies the correct gating function.
Signed-off-by: Jason Stubbs <jasonbstubbs@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits)
drivers/gpu/drm/radeon/atom.c: fix warning
drm/radeon/kms: bump kms version number
drm/radeon/kms: properly set num banks for fusion asics
drm/radeon/kms/atom: move dig phy init out of modesetting
drm/radeon/kms/cayman: fix typo in register mask
drm/radeon/kms: fix typo in spread spectrum code
drm/radeon/kms: fix tile_config value reported to userspace on cayman.
drm/radeon/kms: fix incorrect comparison in cayman setup code.
drm/radeon/kms: add wait idle ioctl for eg->cayman
drm/radeon/cayman: setup hdp to invalidate and flush when asked
drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked
agp/uninorth: Fix lockups with radeon KMS and >1x.
drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only
drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices
drm/radeon/kms: fixup eDP connector handling
drm/radeon/kms: bail early for eDP in hotplug callback
drm/radeon/kms: simplify hotplug handler logic
drm/radeon/kms: rewrite DP handling
drm/radeon/kms/atom: add support for setting DP panel mode
drm/radeon/kms: atombios.h updates for DP panel mode
...
* 'keithp/drm-intel-next' of ../drm-next:
drm/i915: initialize gen6 rps work queue on Sandy Bridge and Ivy Bridge
drm/i915/sdvo: Reorder i2c initialisation before ddc proxy
drm/i915: FDI link training broken on Ironlake by Ivybridge integration
drm/i915: enable rc6 by default
drm/i915: add fbc enable flag, but disable by default
drm/i915: clean up unused ring_get_irq/ring_put_irq functions
drm/i915: fix user irq miss in BSD ring on g4x
Commit 357555c00f split out IVB-specific
register definitions for FDI link training, but a piece of that commit
stopped executing some critical code on Ironlake systems while leaving
it running on Sandybridge.
Turn that code back on both Ironlake and Sandybridge
Signed-off-by: Keith Packard <keithp@keithp.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
FBC has too many corner cases that we don't currently deal with, so
disable it by default so we can enable more important features like RC6,
which conflicts in some configurations.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31742
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'keithp/drm-intel-next' of /ssd/git/drm-next: (301 commits)
drm/i915: split PCH clock gating init
drm/i915: add Ivybridge clock gating init function
drm/i915: Update the location of the ringbuffers' HWS_PGA registers for IVB.
drm/i915: Add support for fence registers on Ivybridge.
drm/i915: Use existing function instead of open-coding fence reg clear.
drm/i915: split clock gating init into per-chipset functions
drm/i915: set IBX pch type explicitly
drm/i915: add Ivy Bridge PCI IDs and driver feature structs
drm/i915: add PantherPoint PCH ID
agp/intel: add Ivy Bridge support
drm/i915: ring support for Ivy Bridge
drm/i915: page flip support for Ivy Bridge
drm/i915: interrupt & vblank support for Ivy Bridge
drm/i915: treat Ivy Bridge watermarks like Sandy Bridge
drm/i915: manual FDI training for Ivy Bridge
drm/i915: add swizzle/tiling support for Ivy Bridge
drm/i915: Ivy Bridge has split display and pipe control
drm/i915: add IS_IVYBRIDGE macro for checks
drm/i915: add IS_GEN7 macro to cover Ivy Bridge and later
drm/i915: split enable/disable vblank code into chipset specific functions
...
Ibex Peak and CougarPoint already require a different setting (added
here), and future chips will likely follow that precedent.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Some of the bits have changed, including one we were setting that enables
a VGA test mode, preventing pipe B from working at all. So add a new
IVB specific function with the right bits.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
This helps contain the mess to init_display() instead.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Treat Ivy Bridge like previous chips as far as flip submission is
concerned.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Not fully tested.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
A0 stepping chips need to use manual training, but the bits have all
moved. So fix things up so we can at least train FDI for VGA links.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Rather than branching in ironlake_pch_enable, add a new train_fdi
function to the display function pointer struct and use it instead.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
This reverts commit 49183b2818.
Quoth Franz Melchior:
"This patch introduces a bug on my infamous "Acer Travelmate
5735Z-452G32Mnss": when KMS takes over, the frame buffer contents get
completely garbled up on screen, with colored stripes and unreadable
text (photo on request). Only when X11 is started, the screen gets
restored again. Closing and re-opening the lid partly cures the
mess, too: it makes the font readable, though horizontally stretched."
Acked-by: Keith Packard <keithp@keithp.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The render P-state handling code requires reading from a GT register.
This means that FORCEWAKE must be written to, a resource which is shared
and should be protected by struct_mutex. Hence we can not manipulate
that register from within the interrupt handling and so must delegate
the task to a workqueue.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Found by the new strict checking for the mutex being held whilst
manipulating the forcewake status.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Provide a reference count to track the forcewake state of the GPU and
give a safe mechanism for userspace to wake the GT. This also potentially
saves a UC read if the GT is known to be awake already.
The reference count is atomic, but the register access and hardware wake
sequence is protected by struct_mutex.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the outputs are active and continuing to access the GATT when we
teardown the PTEs, then there is a potential for us to hang the GPU.
The hang tends to be a PGTBL_ER with either an invalid host access or
an invalid display plane fetch.
v2: Reorder IRQ initialisation to defer until after GEM is setup.
Reported-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch> (855GM)
Tested-by: Pekka Enberg <penberg@kernel.org>
# note that this doesn't fix the underlying problem of the
PGTBL_ER and pipe underruns being reported immediately upon
init on his 965GM MacBook
Reported-and-tested-by: Rick Bramley <richard.bramley@hp.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35635
Reported-and-tested-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36048
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
For debug & testing.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There is a race condition between setting PWRCTXA and executing
MI_SET_CONTEXT. PWRCTXA must not be set until a valid context has been
written (or else the GPU could possible go into rc6, and return to an
invalid context).
Reported-and-Tested-by: Gu Rui <chaos.proton@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28582
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
In the failure cases during rc6 initialization, both the power context
and render context may get !refcount without holding struct_mutex.
However, on rc6 disabling, the lock is held by the caller.
Rearranged the locking so that it's safe in both cases.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
They're used in one place, and not providing any descriptive value,
with their names just being approximately the conjunction of the
struct name and the struct field.
This diff was produced with gcc -E, copying the new struct definitions
out, moving a couple of the old comments into place in the new
structs, and reindenting.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We used to have these from the product of (pch, non-pch) * (pipe a,
pipe b). Now we can just use the nice per-pipe reg macros in the
split out crtc_mode_sets.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
While g4x had DP, eDP came with Ironlake, so we don't need that code here.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This path, which shouldn't be *that* complicated, is now so littered
with per-chipset tweaks that it's hard to trace the order of what
happens. HAS_PCH_SPLIT() is the most radical change across chipsets,
so it seems like a natural split to simplify the code.
This first commit just copies the existing code without changing
anything.
v2: updated to track removal of call to intel_enable_plane from i9xx_crtc_mode_set
Signed-off-by: Eric Anholt <eric@anholt.net>
Hella-acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to ensure that we feed valid memory into the display plane
attached to the pipe when switching the pipe on. Otherwise, the display
engine may read through an invalid PTE and so throw an PGTBL_ER
exception.
As we need to perform load detection before even the first object is
allocated for the fbdev, there is no pre-existing object large enough
for us to borrow to use as the framebuffer. So we need to create one
and cleanup afterwards. At other times, the current fbcon may be large
enough for us to borrow it for duration of load detection.
Found by assert_fb_bound_for_plane().
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As we now never attempt to steal a crtc for load detection, we either
set a mode on a new pipe, or change the dpms mode on an existing pipe.
Never both, so we can simplify the code slightly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As we only allow the use of a disabled CRTC, we don't need to handle the
case where we are reusing an already enabled pipe.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and the no longer relevant comment. The code ceased stealing a pipe
for load detection a long time ago.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Keep all the state required for undoing and restoring the previous pipe
configuration together in a single struct passed from
intel_get_load_detect_pipe() to intel_release_load_detect_pipe() rather
than stuffing them inside the common encoder structure.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Check the return value from drm_crtc_set_mode(), report the failure
via a debug message and propagate the error back to the caller. This
prevents us from blissfully continuing to do the load detection on a
disabled pipe. Fortunately actual failure for modesetting is very rare,
and reported failures even rarer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and so remove the confusion as to whether to use the returned crtc
or intel_encoder->base.crtc with the subsequent load-detection. Even
though they were the same, the two instances of load-detection code
disagreed over which was the more correct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Despite the fixes in 548f245ba6 (drm/i915: fix per-pipe reads after
"cleanup"), we missed one neighbouring read that was mistakenly replaced
with the reg value in 9db4a9c (drm/i915: cleanup per-pipe reg usage).
This was preventing us from correctly determining the mode the BIOS left
the panel in for machines that neither have an OpRegion nor access to
the VBT, (e.g. the EeePC 700).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
When enabling the plane, it is helpful to have already pointed that
plane to valid memory or else we may incur the wrath of a PGTBL_ER.
This code preserved the behaviour from the bad old days for unknown
reasons...
Found by assert_fb_bound_for_plane().
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Add __attribute__((format (printf, 4, 5))) to drm_ut_debug_printk
and fix fallout.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were using uninitialised watermarks values for disabled pipes which
were combined into a single WM register and so corrupting the values for
the enabled pipe and upsetting the display hardware.
Reported-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32612
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Similar to booting, we need to inspect the state left by the BIOS and
remove any conflicting bits before we take over. The example reported by
Seth Forshee is very similar to the bug we encountered with the state left
by grub2, that the crtc pipe<->planning mapping was reversed from our
expectations and so we failed to turn off the outputs when booting or,
in this case, resuming. This may be in fact the same bug, but triggered
at resume time.
This patch rearranges the code we already have to clear up the
conflicting state upon init and calls it from reset (which is called
after we have lost control of the hardware, i.e. along both the boot and
resume paths) instead.
Reported-and-tested-by: Seth Forshee <seth.forshee@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35796
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Fix up the debug file to report the right frequencies. On SNB, we program
the PCU with a frequency ratio, which is multiplied by 100MHz on the CPU
side. But GFX only runs at half that, so report it as such to avoid
confusion.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
A broken implementation of is_pot() prevented the detection of when a
singular pipe was enabled. Eric Anholt pointed out the existence of
is_power_of_2() so use that instead of our broken code!
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35402
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Tested-by: xunx.fang@intel.com
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the pipe or plane is already enabled, then we do not need to enable
it again and can skip the delay. Similarly if it is already disabled
when we want to disable it, we can also skip it.
This fixes a regression from b24e717988, which caused the LVDS
output on one PineView machine to become corrupt after changing
orientation several times.
References: https://bugs.freedesktop.org/show_bug.cgi?id=34601
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Tested-by: mengmeng.meng@intel.com
... as wait_for_vblank (and friends) will do a flush of the MMIO writes
anyway.
References: https://bugs.freedesktop.org/show_bug.cgi?id=34601
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Whilst the GT is powered down (rc6), writes to MMADDR are placed in a
FIFO by the System Agent. This is a limited resource, only 64 entries, of
which 20 are reserved for Display and PCH writes, and so we must take
care not to queue up too many writes. To avoid this, there is counter
which we can poll to ensure there are sufficient free entries in the
fifo.
"Issuing a write to a full FIFO is not supported; at worst it could
result in corruption or a system hang."
Reported-and-Tested-by: Matt Turner <mattst88@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34056
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After disabling, we're meant to teardown the bo used for the contexts,
not recurse into ourselves again and preventing module unload.
Reported-and-tested-by: Ben Widawsky <bwidawsk@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The code paths for modesetting are growing in complexity as we may need
to move the buffers around in order to fit the scanout in the aperture.
Therefore we face a choice as to whether to thread the interruptible status
through the entire pinning and unbinding code paths or to add a flag to
the device when we may not be interrupted by a signal. This does the
latter and so fixes a few instances of modesetting failures under stress.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Dave Airlie spotted that we had a potential bug should we ever rearrange
the drm_i915_gem_object so not the base drm_gem_object was not its first
member. He noticed that we often convert the return of
drm_gem_object_lookup() immediately into drm_i915_gem_object and then
check the result for nullity. This is only valid when the base object is
the first member and so the superobject has the same address. Play safe
instead and use the compiler to convert back to the original return
address for sanity testing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In a few places I replaced reads of per-pipe registers with the actual
register offsets themselves (converting I915_READ(reg) to _PIPE(reg)).
Alexey caught this on his 9xx machine because the cursor control write
was affected. A quick audit showed a few more places where I'd borked
a read, so here's a patch to fix things up.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: compilation fix]
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 633f2ea266 and the
attempted fix dcbe6f2b3d.
There is a single clock source used for both SSC (some LVDS and DP) and
non-SSC (VGA, DVI) outputs. So we need to be careful to only enable SSC
as necessary. However, fiddling with DREFCLK was causing DP links to be
dropped and we do not have a fix ready, so revert.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
eDP on the CPU doesn't need the PCH set up at all, it can in fact cause
problems. So avoid FDI training and PCH PLL enabling in that case.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the gpu is hung, then whatever was inside the render cache is lost
and there is little point waiting for it. Or complaining if we see an
EIO or EAGAIN instead. So, if the GPU is indeed in its death throes when
we need to rewrite the registers for a new framebuffer, just ignore the
error and proceed with the update.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Grab the latest stabilisation bits from -fixes and some suspend and
resume fixes from linus.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_irq.c
If the gpu is hung, then whatever was inside the render cache is lost
and there is little point waiting for it. Or complaining if we see an
EIO or EAGAIN instead. So, if the GPU is indeed in its death throes when
we need to rewrite the registers for a new framebuffer, just ignore the
error and proceed with the update.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Disable any PCH ports associated with a pipe when disabling it. This
should prevent transcoder disable failures due to ports still being on.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: introduce *_PIPE_ENABLED() macro]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The irony of the patch to fix the resume regression on PineView causing
a further regression on Ironlake is not lost on me.
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Reported-by: Björn Schließmann <chronoss@gmx.de>
Tested-by: Björn Schließmann <chronoss@gmx.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28802
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The automatic powersaving feature is once again causing havoc, with 100%
reliable hangs on boot and resume on affected machines.
Reported-by: Francesco Allertsen <fallertsen@gmail.com>
Reported-by: Gui Rui <chaos.proton@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28582
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We had some conversions over to the _PIPE macros, but didn't get
everything. So hide the per-pipe regs with an _ (still used in a few
places for legacy) and add a few _PIPE based macros, then make sure
everyone uses them.
[update: remove usage of non-existent no-op macro]
[update 2: keep modesetting suspend/resume code, update to new reg names]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: stylistic cleanups for checkpatch and taste]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The PCH can drive several reference clocks simultaneously, and needs to
with multiple display configurations. So we can't just clobber the
existing state everytime we set a mode, we need to take into account
what the other CRTCs are doing at the time.
Doing so fixes an issue where you'd lose the LVDS display at boot if you
had an LVDS+DP config.
[updated: init bools and check CRTC status correctly]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When a transcoder is disabled, any ports pointing at it should also be
disabled. If they're not, we may fail to disable the transcoder,
leading to blank displays.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These bits have a different meaning on ILK+, where planes are hardwired
to pipes. Fixing this avoid some spurious assertion failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Based on a patch by Takashi Iwai.
Reported-by: Matthias Hopf <mat@mshopf.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=27272
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Move the plane->mode config to the point of use rather than repeatedly
querying the same information.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Keith Packard