Bump the ZO_z_extra_bytes margin for zstd.
Zstd needs 3 bytes per 128 KB, and has a 22 byte fixed overhead.
Zstd needs to maintain 128 KB of space at all times, since that is
the maximum block size. See the comments regarding in-place
decompression added in lib/decompress_unzstd.c for details.
The existing code is written so that all the compression algorithms use
the same ZO_z_extra_bytes. It is taken to be the maximum of the growth
rate plus the maximum fixed overhead. The comments just above this diff
state that:
Signed-off-by: Nick Terrell <terrelln@fb.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200730190841.2071656-6-nickrterrell@gmail.com
Store the kernel's link address as ImageBase in the PE header. Note that
the PE specification requires the ImageBase to be 64k aligned. The
preferred address should almost always satisfy that, except for 32-bit
kernel if the configuration has been customized.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200303221205.4048668-4-nivedita@alum.mit.edu
Link: https://lore.kernel.org/r/20200308080859.21568-18-ardb@kernel.org
Now that we have added new ways to load the initrd or the mixed mode
kernel, we will also need a way to tell the loader about this. Add
symbolic constants for the PE/COFF major/minor version numbers (which
fortunately have always been 0x0 for all architectures), so that we
can bump them later to document the capabilities of the stub.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Replace bare numbers in the PE/COFF header structure with symbolic
constants so they become self documenting.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Currently, mixed mode is closely tied to the EFI handover protocol
and relies on intimate knowledge of the bootparams structure, setup
header etc, all of which are rather byzantine and entirely specific
to x86.
Even though no other EFI supported architectures are currently known
that could support something like mixed mode, it still makes sense to
abstract a bit from this, and make it part of a generic Linux on EFI
boot protocol.
To that end, add a .compat section to the mixed mode binary, and populate
it with the PE machine type and entry point address, allowing firmware
implementations to match it to their native machine type, and invoke
non-native binaries using a secondary entry point.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
In commit
c7fb93ec51 ("x86/efi: Include a .bss section within the PE/COFF headers")
we added a separate .bss section to the PE/COFF header of the compressed
kernel describing the static memory footprint of the decompressor, to
ensure that it has enough headroom to decompress itself.
We can achieve the exact same result by increasing the virtual size of
the .text section, without changing the raw size, which, as per the
PE/COFF specification, requires the loader to zero initialize the delta.
Doing so frees up a slot in the section table, which we will use later
to describe the mixed mode entrypoint.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The setup_data is a bit awkward to use for extremely large data objects,
both because the setup_data header has to be adjacent to the data object
and because it has a 32-bit length field. However, it is important that
intermediate stages of the boot process have a way to identify which
chunks of memory are occupied by kernel data. Thus introduce an uniform
way to specify such indirect data as setup_indirect struct and
SETUP_INDIRECT type.
And finally bump setup_header version in arch/x86/boot/header.S.
Suggested-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Ross Philipson <ross.philipson@oracle.com>
Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: ard.biesheuvel@linaro.org
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: dave.hansen@linux.intel.com
Cc: eric.snowberg@oracle.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Juergen Gross <jgross@suse.com>
Cc: kanth.ghatraju@oracle.com
Cc: linux-doc@vger.kernel.org
Cc: linux-efi <linux-efi@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rdunlap@infradead.org
Cc: ross.philipson@oracle.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Cc: xen-devel@lists.xenproject.org
Link: https://lkml.kernel.org/r/20191112134640.16035-4-daniel.kiper@oracle.com
The relationships between the headers are analogous to the various data
sections:
setup_header = .data
boot_params/setup_data = .bss
What is missing from the above list? That's right:
kernel_info = .rodata
We have been (ab)using .data for things that could go into .rodata or .bss for
a long time, for lack of alternatives and -- especially early on -- inertia.
Also, the BIOS stub is responsible for creating boot_params, so it isn't
available to a BIOS-based loader (setup_data is, though).
setup_header is permanently limited to 144 bytes due to the reach of the
2-byte jump field, which doubles as a length field for the structure, combined
with the size of the "hole" in struct boot_params that a protected-mode loader
or the BIOS stub has to copy it into. It is currently 119 bytes long, which
leaves us with 25 very precious bytes. This isn't something that can be fixed
without revising the boot protocol entirely, breaking backwards compatibility.
boot_params proper is limited to 4096 bytes, but can be arbitrarily extended
by adding setup_data entries. It cannot be used to communicate properties of
the kernel image, because it is .bss and has no image-provided content.
kernel_info solves this by providing an extensible place for information about
the kernel image. It is readonly, because the kernel cannot rely on a
bootloader copying its contents anywhere, but that is OK; if it becomes
necessary it can still contain data items that an enabled bootloader would be
expected to copy into a setup_data chunk.
Do not bump setup_header version in arch/x86/boot/header.S because it
will be followed by additional changes coming into the Linux/x86 boot
protocol.
Suggested-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Ross Philipson <ross.philipson@oracle.com>
Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: ard.biesheuvel@linaro.org
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: dave.hansen@linux.intel.com
Cc: eric.snowberg@oracle.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Juergen Gross <jgross@suse.com>
Cc: kanth.ghatraju@oracle.com
Cc: linux-doc@vger.kernel.org
Cc: linux-efi <linux-efi@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rdunlap@infradead.org
Cc: ross.philipson@oracle.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Cc: xen-devel@lists.xenproject.org
Link: https://lkml.kernel.org/r/20191112134640.16035-2-daniel.kiper@oracle.com
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
The current kernel supports 5-level paging mode, and supports dynamically
choosing the paging mode during bootup depending on the kernel image,
hardware and kernel parameter settings. This flexibility brings several
issues to kexec/kdump:
1) Dynamic switching between paging modes requires support in the target
kernel. This means kexec from a 5-level paging kernel into a kernel
which does not support mode switching is not possible. So the loader
needs to be able to analyze the supported paging modes of the kexec
target kernel.
2) If running on a 5-level paging kernel and the kexec target kernel is a
4-level paging kernel, the target immage cannot be loaded above the 64TB
address space limit. But the kexec loader searches for a load area from
top to bottom which would eventually put the target kernel above 64TB
when the machine has large enough RAM size. So the loader needs to be
able to analyze the paging mode of the target kernel to load it at a
suitable spot in the address space.
Solution:
Add two bits XLF_5LEVEL and XLF_5LEVEL_ENABLED:
- Bit XLF_5LEVEL indicates whether 5-level paging mode switching support
is available. (Issue #1)
- Bit XLF_5LEVEL_ENABLED indicates whether the kernel was compiled with
full 5-level paging support (CONFIG_X86_5LEVEL=y). (Issue #2)
The loader will use these bits to verify whether the target kernel is
suitable to be kexec'ed to from a 5-level paging kernel and to determine
the constraints of the target kernel load address.
The flags will be used by the kernel kexec subsystem and the userspace
kexec tools.
[ tglx: Massaged changelog ]
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dyoung@redhat.com
Link: https://lkml.kernel.org/r/20190524073810.24298-2-bhe@redhat.com
Mostly due to x86 and acpi conversion, several documentation
links are still pointing to the old file. Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Peter Anvin pointed out that commit:
ae7e1238e6 ("x86/boot: Add ACPI RSDP address to setup_header")
should be reverted as setup_header should only contain items set by the
legacy BIOS.
So revert said commit. Instead of fully reverting the dependent commit
of:
e7b66d16fe ("x86/acpi, x86/boot: Take RSDP address for boot params if available")
just remove the setup_header reference in order to replace it by
a boot_params in a followup patch.
Suggested-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: boris.ostrovsky@oracle.com
Cc: bp@alien8.de
Cc: daniel.kiper@oracle.com
Cc: sstabellini@kernel.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20181120072529.5489-2-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Xen PVH guests receive the address of the RSDP table from Xen. In order
to support booting a Xen PVH guest via Grub2 using the standard x86
boot entry we need a way for Grub2 to pass the RSDP address to the
kernel.
For this purpose expand the struct setup_header to hold the physical
address of the RSDP address. Being zero means it isn't specified and
has to be located the legacy way (searching through low memory or
EBDA).
While documenting the new setup_header layout and protocol version
2.14 add the missing documentation of protocol version 2.13.
There are Grub2 versions in several distros with a downstream patch
violating the boot protocol by writing past the end of setup_header.
This requires another update of the boot protocol to enable the kernel
to distinguish between a specified RSDP address and one filled with
garbage by such a broken Grub2.
From protocol 2.14 on Grub2 will write the version it is supporting
(but never a higher value than found to be supported by the kernel)
ored with 0x8000 to the version field of setup_header. This enables
the kernel to know up to which field Grub2 has written information
to. All fields after that are supposed to be clobbered.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: boris.ostrovsky@oracle.com
Cc: bp@alien8.de
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20181010061456.22238-3-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The <generated/utsrelease.h> defines UTS_RELEASE, but I do not
see any reference to it in arch/x86/boot/header.S.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1505921232-8960-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current slack space is not enough for LZ4, which has a worst case
overhead of 0.4% for data that cannot be further compressed. With
an LZ4 compressed kernel with an embedded initrd, the output is likely
to overwrite the input.
Increase the slack space to avoid that.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1503842124-29718-1-git-send-email-jschoenh@amazon.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There's an assembly guard in asm/e820/types.h, and only
a single .S file includes this header: arch/x86/boot/header.S,
but it does not actually make use of any of the E820 defines.
Remove the inclusion and remove the assembly guard as well.
No change in functionality.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In line with asm/e820/types.h, move the e820 API declarations to
asm/e820/api.h and update all usage sites.
This is just a mechanical, obviously correct move & replace patch,
there will be subsequent changes to clean up the code and to make
better use of the new header organization.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently z_extract_offset is calculated in boot/compressed/mkpiggy.c.
This doesn't work well because mkpiggy.c doesn't know the details of the
decompressor in use. As a result, it can only make an estimation, which
has risks:
- output + output_len (VO) could be much bigger than input + input_len
(ZO). In this case, the decompressed kernel plus relocs could overwrite
the decompression code while it is running.
- The head code of ZO could be bigger than z_extract_offset. In this case
an overwrite could happen when the head code is running to move ZO to
the end of buffer. Though currently the size of the head code is very
small it's still a potential risk. Since there is no rule to limit the
size of the head code of ZO, it runs the risk of suddenly becoming a
(hard to find) bug.
Instead, this moves the z_extract_offset calculation into header.S, and
makes adjustments to be sure that the above two cases can never happen,
and further corrects the comments describing the calculations.
Since we have (in the previous patch) made ZO always be located against
the end of decompression buffer, z_extract_offset is only used here to
calculate an appropriate buffer size (INIT_SIZE), and is not longer used
elsewhere. As such, it can be removed from voffset.h.
Additionally clean up #if/#else #define to improve readability.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Baoquan He <bhe@redhat.com>
[ Rewrote the changelog and comments. ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: lasse.collin@tukaani.org
Link: http://lkml.kernel.org/r/1461888548-32439-4-git-send-email-keescook@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The comment that describes the analysis for the size of the decompressor
code only took gzip into account (there are currently 6 other decompressors
that could be used). The actual z_extract_offset calculation in code was
already handling the correct maximum size, but this documentation hadn't
been updated. This updates the documentation, fixes several typos, moves
the comment to header.S, updates references, and adds a note at the end
of the decompressor include list to remind us about updating the comment
in the future.
(Instead of moving the comment to mkpiggy.c, where the calculation
is currently happening, it is being moved to header.S because
the calculations in mkpiggy.c will be removed in favor of header.S
calculations in a following patch, and it seemed like overkill to move
the giant comment twice, especially when there's already reference to
z_extract_offset in header.S.)
Signed-off-by: Baoquan He <bhe@redhat.com>
[ Rewrote changelog, cleaned up comment style, moved comments around. ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1461185746-8017-2-git-send-email-keescook@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are two kexec load syscalls, kexec_load another and kexec_file_load.
kexec_file_load has been splited as kernel/kexec_file.c. In this patch I
split kexec_load syscall code to kernel/kexec.c.
And add a new kconfig option KEXEC_CORE, so we can disable kexec_load and
use kexec_file_load only, or vice verse.
The original requirement is from Ted Ts'o, he want kexec kernel signature
being checked with CONFIG_KEXEC_VERIFY_SIG enabled. But kexec-tools use
kexec_load syscall can bypass the checking.
Vivek Goyal proposed to create a common kconfig option so user can compile
in only one syscall for loading kexec kernel. KEXEC/KEXEC_FILE selects
KEXEC_CORE so that old config files still work.
Because there's general code need CONFIG_KEXEC_CORE, so I updated all the
architecture Kconfig with a new option KEXEC_CORE, and let KEXEC selects
KEXEC_CORE in arch Kconfig. Also updated general kernel code with to
kexec_load syscall.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit:
aeffc4928e ("x86/efi: Request desired alignment via the PE/COFF headers")
Linn reports that Signtool complains that kernels built with
CONFIG_EFI_STUB=y are violating the PE/COFF specification because
the 'SizeOfImage' field is not a multiple of 'SectionAlignment'.
This violation was introduced as an optimisation to skip having
the kernel relocate itself during boot and instead have the
firmware place it at a correctly aligned address.
No one else has complained and I'm not aware of any firmware
implementations that refuse to boot with commit aeffc4928e,
but it's a real bug, so revert the offending commit.
Reported-by: Linn Crosetto <linn@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Brown <mbrown@fensystems.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1438936621-5215-3-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull EFI changes from Ingo Molnar:
"Main changes in this cycle are:
- arm64 efi stub fixes, preservation of FP/SIMD registers across
firmware calls, and conversion of the EFI stub code into a static
library - Ard Biesheuvel
- Xen EFI support - Daniel Kiper
- Support for autoloading the efivars driver - Lee, Chun-Yi
- Use the PE/COFF headers in the x86 EFI boot stub to request that
the stub be loaded with CONFIG_PHYSICAL_ALIGN alignment - Michael
Brown
- Consolidate all the x86 EFI quirks into one file - Saurabh Tangri
- Additional error logging in x86 EFI boot stub - Ulf Winkelvos
- Support loading initrd above 4G in EFI boot stub - Yinghai Lu
- EFI reboot patches for ACPI hardware reduced platforms"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
efi/arm64: Handle missing virtual mapping for UEFI System Table
arch/x86/xen: Silence compiler warnings
xen: Silence compiler warnings
x86/efi: Request desired alignment via the PE/COFF headers
x86/efi: Add better error logging to EFI boot stub
efi: Autoload efivars
efi: Update stale locking comment for struct efivars
arch/x86: Remove efi_set_rtc_mmss()
arch/x86: Replace plain strings with constants
xen: Put EFI machinery in place
xen: Define EFI related stuff
arch/x86: Remove redundant set_bit(EFI_MEMMAP) call
arch/x86: Remove redundant set_bit(EFI_SYSTEM_TABLES) call
efi: Introduce EFI_PARAVIRT flag
arch/x86: Do not access EFI memory map if it is not available
efi: Use early_mem*() instead of early_io*()
arch/ia64: Define early_memunmap()
x86/reboot: Add EFI reboot quirk for ACPI Hardware Reduced flag
efi/reboot: Allow powering off machines using EFI
efi/reboot: Add generic wrapper around EfiResetSystem()
...
The EFI boot stub goes to great pains to relocate the kernel image to
an appropriately aligned address, as indicated by the ->kernel_alignment
field in the bzImage header. However, for the PE stub entry case, we
can request that the EFI PE/COFF loader do the work for us.
Fix by exposing the desired alignment via the SectionAlignment field
in the PE/COFF headers. Despite its name, this field provides an
overall alignment requirement for the loaded file. (Naturally, the
FileAlignment field describes the alignment for individual sections.)
There is no way in the PE/COFF headers to express the concept of
min_alignment; we therefore do not expose the minimum (as opposed to
preferred) alignment.
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The PE/COFF headers currently describe only the initialised-data
portions of the image, and result in no space being allocated for the
uninitialised-data portions. Consequently, the EFI boot stub will end
up overwriting unexpected areas of memory, with unpredictable results.
Fix by including a .bss section in the PE/COFF headers (functionally
equivalent to the init_size field in the bzImage header).
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Cc: Thomas Bächler <thomas@archlinux.org>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
commit 7d453eee36 ("x86/efi: Wire up CONFIG_EFI_MIXED") introduced a
regression for the functionality to load kernels above 4G. The relevant
(incorrect) reasoning behind this change can be seen in the commit
message,
"The xloadflags field in the bzImage header is also updated to reflect
that the kernel supports both entry points by setting both of
XLF_EFI_HANDOVER_32 and XLF_EFI_HANDOVER_64 when CONFIG_EFI_MIXED=y.
XLF_CAN_BE_LOADED_ABOVE_4G is disabled so that the kernel text is
guaranteed to be addressable with 32-bits."
This is obviously bogus since 32-bit EFI loaders will never place the
kernel above the 4G mark. So this restriction is entirely unnecessary.
But things are worse than that - since we want to encourage people to
always compile with CONFIG_EFI_MIXED=y so that their kernels work out of
the box for both 32-bit and 64-bit firmware, commit 7d453eee36
effectively disables XLF_CAN_BE_LOADED_ABOVE_4G completely.
Remove the overzealous and superfluous restriction and restore the
XLF_CAN_BE_LOADED_ABOVE_4G functionality.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1402140380-15377-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Pull x86 EFI changes from Ingo Molnar:
"The main changes:
- Add debug code to the dump EFI pagetable - Borislav Petkov
- Make 1:1 runtime mapping robust when booting on machines with lots
of memory - Borislav Petkov
- Move the EFI facilities bits out of 'x86_efi_facility' and into
efi.flags which is the standard architecture independent place to
keep EFI state, by Matt Fleming.
- Add 'EFI mixed mode' support: this allows 64-bit kernels to be
booted from 32-bit firmware. This needs a bootloader that supports
the 'EFI handover protocol'. By Matt Fleming"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
x86, efi: Abstract x86 efi_early calls
x86/efi: Restore 'attr' argument to query_variable_info()
x86/efi: Rip out phys_efi_get_time()
x86/efi: Preserve segment registers in mixed mode
x86/boot: Fix non-EFI build
x86, tools: Fix up compiler warnings
x86/efi: Re-disable interrupts after calling firmware services
x86/boot: Don't overwrite cr4 when enabling PAE
x86/efi: Wire up CONFIG_EFI_MIXED
x86/efi: Add mixed runtime services support
x86/efi: Firmware agnostic handover entry points
x86/efi: Split the boot stub into 32/64 code paths
x86/efi: Add early thunk code to go from 64-bit to 32-bit
x86/efi: Build our own EFI services pointer table
efi: Add separate 32-bit/64-bit definitions
x86/efi: Delete dead code when checking for non-native
x86/mm/pageattr: Always dump the right page table in an oops
x86, tools: Consolidate #ifdef code
x86/boot: Cleanup header.S by removing some #ifdefs
efi: Use NULL instead of 0 for pointer
...
Add the Kconfig option and bump the kernel header version so that boot
loaders can check whether the handover code is available if they want.
The xloadflags field in the bzImage header is also updated to reflect
that the kernel supports both entry points by setting both of
XLF_EFI_HANDOVER_32 and XLF_EFI_HANDOVER_64 when CONFIG_EFI_MIXED=y.
XLF_CAN_BE_LOADED_ABOVE_4G is disabled so that the kernel text is
guaranteed to be addressable with 32-bits.
Note that no boot loaders should be using the bits set in xloadflags to
decide which entry point to jump to. The entire scheme is based on the
concept that 32-bit bootloaders always jump to ->handover_offset and
64-bit loaders always jump to ->handover_offset + 512. We set both bits
merely to inform the boot loader that it's safe to use the native
handover offset even if the machine type in the PE/COFF header claims
otherwise.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
handover_offset is now filled out by build.c. Don't set a default value
as it will be overwritten anyway.
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Old kexec-tools can not load new kernels. The reason is kexec-tools does
not fill efi_info in x86 setup header previously, thus EFI failed to
initialize. In new kexec-tools it will by default to fill efi_info and
pass other EFI required infomation to 2nd kernel so kexec kernel EFI
initialization can succeed finally.
To prevent from breaking userspace, add a new xloadflags bit so
kexec-tools can check the flag and switch to old logic.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
xloadflags bit 1 indicates that we can load the kernel and all data
structures above 4G; it is set if kernel is relocatable and 64bit.
bootloader will check if xloadflags bit 1 is set to decide if
it could load ramdisk and kernel high above 4G.
bootloader will fill value to ext_ramdisk_image/size for high 32bits
when it load ramdisk above 4G.
kernel use get_ramdisk_image/size to use ext_ramdisk_image/size to get
right positon for ramdisk.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Rob Landley <rob@landley.net>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Define the 2.12 bzImage boot protocol: add xloadflags and additional
fields to allow the command line, initramfs and struct boot_params to
live above the 4 GiB mark.
The xloadflags now communicates if this is a 64-bit kernel with the
legacy 64-bit entry point and which of the EFI handover entry points
are supported.
Avoid adding new read flags to loadflags because of claimed
bootloaders testing the whole byte for == 1 to determine bzImageness
at least until the issue can be researched further.
This is based on patches by Yinghai Lu and David Woodhouse.
Originally-by: Yinghai Lu <yinghai@kernel.org>
Originally-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
Commit 2e064b1 (x86, efi: Fix issue of overlapping .reloc section for
EFI_STUB) removed a dummy reloc added by commit 291f363 (x86, efi: EFI
boot stub support), but forgot to remove the dummy long used by that
reloc.
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Tested-by: Lee G Rosenbaum <lee.g.rosenbaum@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The named constant RAMDISK is unused. It used to set the (obsolete)
kernel boot header field ram_size, but its usage for that purpose got
dropped in commit 5e47c478b0 ("x86: remove
zImage support"). Now remove this constant too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Link: http://lkml.kernel.org/r/1345396003.1771.9.camel@x61.thuisdomein
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pul x86/efi changes from Ingo Molnar:
"This tree adds an EFI bootloader handover protocol, which, once
supported on the bootloader side, will make bootup faster and might
result in simpler bootloaders.
The other change activates the EFI wall clock time accessors on x86-64
as well, instead of the legacy RTC readout."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Handover Protocol
x86-64/efi: Use EFI to deal with platform wall clock
Pull x86 cleanup and cpufeature from Ingo Molnar:
"Just a single cleanup and and a commit that adds new CPU feature
names"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Remove ancient, unconditionally #ifdef'd out dead code
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: Add the RDSEED and ADX features
As things currently stand, traditional EFI boot loaders and the EFI
boot stub are carrying essentially the same initialisation code
required to setup an EFI machine for booting a kernel. There's really
no need to have this code in two places and the hope is that, with
this new protocol, initialisation and booting of the kernel can be
left solely to the kernel's EFI boot stub. The responsibilities of the
boot loader then become,
o Loading the kernel image from boot media
File system code still needs to be carried by boot loaders for the
scenario where the kernel and initrd files reside on a file system
that the EFI firmware doesn't natively understand, such as ext4, etc.
o Providing a user interface
Boot loaders still need to display any menus/interfaces, for example
to allow the user to select from a list of kernels.
Bump the boot protocol number because we added the 'handover_offset'
field to indicate the location of the handover protocol entry point.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-and-Tested-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1342689828-16815-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Release v1.3.82 wrapped a few lines of code in an "#ifdef
SAFE_RESET_DISK_CONTROLLER" and "#endif" pair. Since
SAFE_RESET_DISK_CONTROLLER was never defined anywhere that was basically
a verbose "#ifdef 0" and "#endif" pair. These dead lines have been in
the tree for sixteen years but now the time has come to remove them.
I guess the main lesson here is that if you want your dead code in the
tree for a very long time you'd better be creative. A plain old "#ifdef
0" and "#endif" pair just doesn't cut it!
See: http://lkml.kernel.org/r/199603301718.LAA00178@craie.inetnebr.com
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Link: http://lkml.kernel.org/r/1340230589.1773.7.camel@x61.thuisdomein
Acked-by: Jeff Epler <jepler@unpythonic.net>
Acked-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Some UEFI firmware will not load a .efi with a .reloc section
with a size of 0.
Therefore, we create a .efi image with 4 main areas and 3 sections.
1. PE/COFF file header
2. .setup section (covers all setup code following the first sector)
3. .reloc section (contains 1 dummy reloc entry, created in build.c)
4. .text section (covers the remaining kernel image)
To make room for the new .setup section data, the header
bugger_off_msg had to be shortened.
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Link: http://lkml.kernel.org/r/1339085121-12760-1-git-send-email-jordan.l.justen@intel.com
Tested-by: Lee G Rosenbaum <lee.g.rosenbaum@intel.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We've actually got six data directories in the header, not one. Even
though the firmware loader doesn't seem to mind, when we come to sign
the kernel image the signing tool thinks that there is no Certificate
Table data directory, even though we've allocated space for one.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1332520506-6472-4-git-send-email-jordan.l.justen@intel.com
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This change modifes the PE .text section to start after
the first sector of the kernel image.
The header may be modified by the UEFI secure boot signing,
so it is not appropriate for it to be included in one of the
image sections. Since the sections are part of the secure
boot hash, this modification to the .text section contents
would invalidate the secure boot signed hash.
Note: UEFI secure boot does hash the image header, but
fields that are changed by the signing process are excluded
from the hash calculation. This exclusion process is only
handled for the image header, and not image sections.
Luckily, we can still easily boot without the first sector
by initializing a few fields in arch/x86/boot/compressed/eboot.c.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1332520506-6472-3-git-send-email-jordan.l.justen@intel.com
[jordan.l.justen@intel.com: set .text vma & file offset]
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Previously the .reloc section was embedded in the .text
section.
No relocations are required during the PE/COFF loading phase
for the kernel using the EFI_STUB UEFI loader. To fix the
issue of overlapping sections, create a .reloc section with a
zero length.
The .reloc section header must exist to make sure the image
will be loaded by the UEFI firmware, but a zero-length
section header seems to be sufficient.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Link: http://lkml.kernel.org/r/1332520506-6472-2-git-send-email-jordan.l.justen@intel.com
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There is currently a large divide between kernel development and the
development of EFI boot loaders. The idea behind this patch is to give
the kernel developers full control over the EFI boot process. As
H. Peter Anvin put it,
"The 'kernel carries its own stub' approach been very successful in
dealing with BIOS, and would make a lot of sense to me for EFI as
well."
This patch introduces an EFI boot stub that allows an x86 bzImage to
be loaded and executed by EFI firmware. The bzImage appears to the
firmware as an EFI application. Luckily there are enough free bits
within the bzImage header so that it can masquerade as an EFI
application, thereby coercing the EFI firmware into loading it and
jumping to its entry point. The beauty of this masquerading approach
is that both BIOS and EFI boot loaders can still load and run the same
bzImage, thereby allowing a single kernel image to work in any boot
environment.
The EFI boot stub supports multiple initrds, but they must exist on
the same partition as the bzImage. Command-line arguments for the
kernel can be appended after the bzImage name when run from the EFI
shell, e.g.
Shell> bzImage console=ttyS0 root=/dev/sdb initrd=initrd.img
v7:
- Fix checkpatch warnings.
v6:
- Try to allocate initrd memory just below hdr->inird_addr_max.
v5:
- load_options_size is UTF-16, which needs dividing by 2 to convert
to the corresponding ASCII size.
v4:
- Don't read more than image->load_options_size
v3:
- Fix following warnings when compiling CONFIG_EFI_STUB=n
arch/x86/boot/tools/build.c: In function ‘main’:
arch/x86/boot/tools/build.c:138:24: warning: unused variable ‘pe_header’
arch/x86/boot/tools/build.c:138:15: warning: unused variable ‘file_sz’
- As reported by Matthew Garrett, some Apple machines have GOPs that
don't have hardware attached. We need to weed these out by
searching for ones that handle the PCIIO protocol.
- Don't allocate memory if no initrds are on cmdline
- Don't trust image->load_options_size
Maarten Lankhorst noted:
- Don't strip first argument when booted from efibootmgr
- Don't allocate too much memory for cmdline
- Don't update cmdline_size, the kernel considers it read-only
- Don't accept '\n' for initrd names
v2:
- File alignment was too large, was 8192 should be 512. Reported by
Maarten Lankhorst on LKML.
- Added UGA support for graphics
- Use VIDEO_TYPE_EFI instead of hard-coded number.
- Move linelength assignment until after we've assigned depth
- Dynamically fill out AddressOfEntryPoint in tools/build.c
- Don't use magic number for GDT/TSS stuff. Requested by Andi Kleen
- The bzImage may need to be relocated as it may have been loaded at
a high address address by the firmware. This was required to get my
macbook booting because the firmware loaded it at 0x7cxxxxxx, which
triggers this error in decompress_kernel(),
if (heap > ((-__PAGE_OFFSET-(128<<20)-1) & 0x7fffffff))
error("Destination address too large");
Cc: Mike Waychison <mikew@google.com>
Cc: Matthew Garrett <mjg@redhat.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1321383097.2657.9.camel@mfleming-mobl1.ger.corp.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Correct the calculation of ZO_INIT_SIZE (the amount of memory we need
during decompression). One symbol (ZO_startup_32) was missing from
zoffset.h, and another (ZO_z_extract_offset) was misspelled.
[ Impact: build fix ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Nick Terrell