It is not save to provide memory for an int and then cast the pointer to
it to long*. It is better to standardize the up and down gateway
bandwith representation to simple ints and only use long inside
conversation routines.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv uses pointers which are marked as const and should not
violate that type qualifier by passing it to functions which force a
cast to the non-const version.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The size of void is currently set by gcc to 1, but is not well defined
in general. Therefore it is more advisable to cast it to char* before
doing pointer arithmetic.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Every time that find_router() is invoked, if_status has to be compared with
IF_ACTIVE. Moving this comparison inside find_router() will avoid to write it
each time.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
The broadcast flood protection should be reset to its original value
if the primary interface could not be retrieved.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
add_bcast_packet_to_list increases the refcount for if_incoming but the
reference count is never decreased. The reference count must be
increased for all kinds of forwarded packets which have the primary
interface stored and forw_packet_free must decrease them. Also
purge_outstanding_packets has to invoke forw_packet_free when a work
item was really cancelled.
This regression was introduced in
32ae9b221e.
Reported-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
In function is_bidirectional_neigh the code that find out the one hop
neighbor is duplicated.
Signed-off-by: Daniele Furlan <daniele.furlan@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
It is slightly irritating that comments after a long line span over
multiple lines without any code. It is easier to put them before the
actual code and reduce the number of lines which the eye has to read.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
To be coherent, all the functions/variables/constants have been renamed
to the TranslationTable style
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The hard_if_event is called by the notifier with rtnl_lock and tries to
remove sysfs entries when a NETDEV_UNREGISTER event is received. This
will automatically take the s_active lock.
The s_active lock is also used when a new interface is added to a meshif
through sysfs. In that situation we cannot wait for the rntl_lock before
creating the actual batman-adv interface to prevent a deadlock. It is
still possible to try to get the rtnl_lock and immediately abort the
current operation when the trylock call failed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
hardif_list_lock is unneccessary because we already ensure that no
multiple admin operations can take place through rtnl_lock.
hardif_list_lock only adds additional overhead and complexity.
Critical functions now check whether they are called with rtnl_lock
using ASSERT_RTNL.
It indirectly fixes the problem that orig_hash_del_if() expects that
only one interface is deleted from hardif_list at a time, but
hardif_remove_interfaces() removes all at once and then calls
orig_hash_del_if().
Reported-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The bridge loop detection for batman-adv allows the bat0 interface
to be bridged into an ethernet segment which other batman-adv nodes
are connected to. In order to also allow multiple VLANs on top of
the bat0 interface to be bridged into the ethernet segment this
patch extends the aforementioned bridge loop detection.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The RCU callback softif_neigh_free_rcu() just calls kfree(), so we can
use kfree_rcu() instead of call_rcu().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
The RCU callback neigh_node_free_rcu() just calls kfree(), so we can use
kfree_rcu() instead of call_rcu().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
The RCU callback gw_node_free_rcu() just calls kfree(), so we can use
kfree_rcu() instead of call_rcu().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
The rcu protected macros rcu_dereference() and rcu_assign_pointer()
for the bat_priv->primary_if need to be used, as well as spin/rcu locking.
Otherwise we might end up using a primary_if pointer pointing to already
freed memory.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This is a regression from c4aac1ab9b
- gw_node_update() doesn't add a new gw_node in case of empty curr_gw.
This means that at the beginning no gw_node is added, leading to an
empty gateway list.
- gw_election() is terminating in case of curr_gw == NULL. It has to
terminate in case of curr_gw != NULL
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
atomic_dec_not_zero() is very useful and it is currently defined
multiple times. So it is possible to move it in main.h
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
orig_hash_find() manages rcu_lock/unlock internally and doesn't need to
be surrounded by rcu_read_lock() / rcu_read_unlock() anymore
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Acked-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like other virtual interfaces, e.g. br0, we don't need a transmit
queue. Packets should only be queued on real interfaces which are
underneath. In practice this patch makes little difference since the
virtual interfaces can accept packets as fast as they come, but the
patch will avoid bufferbloat questions to the mailling lists in the
future.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Add get/set wrapper functions for softif_neigh and
use rcu functions to manipulate the pointers.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The rcu protected macros rcu_dereference() and rcu_assign_pointer()
for the orig_node->router need to be used, as well as spin/rcu locking.
Otherwise we might end up using a router pointer pointing to already
freed memory.
Therefore this commit introduces the safe getter method
orig_node_get_router().
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
gw_get_selected() can get us the desired orig_node directly, therefore
reusing that function in gw_check_election().
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Make the return value explicit instead of (void *).
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This decreases the size of find_router() by outsourcing the router
search for the bonding and interface alternating modes to their own sub
functions. This shall make it easier to keep track of the correct
refcounting later.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When trying to associate a net_device with another net_device which
already exists, batman-adv assumes that this interface is a fully
initialized batman mesh interface without checking it. The behaviour
when accessing data behind netdev_priv of a random net_device is
undefined and potentially dangerous.
Reported-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Batman-adv works with "hard interfaces" as well as "soft interfaces".
The new name should better make clear which kind of interfaces this
list stores.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When printing the soft interface table the number of entries in the
softif neigh list are first being counted and a fitting buffer
allocated. After that the softif neigh list gets locked again and
the buffer printed - which has the following two issues:
For one thing, the softif neigh list might have grown when reacquiring
the rcu lock, which results in writing outside of the allocated buffer.
Furthermore 31 Bytes are not enough for printing an entry with a vid
of more than 2 digits.
The manual buffering is unnecessary, we can safely print to the seq
directly during the rcu_read_lock().
Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When unicast_send_skb() is increasing the orig_node's refcount another
thread might have been freeing this orig_node already. We need to
increase the refcount in the rcu read lock protected area to avoid that.
Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The rcu protected macros rcu_dereference() and rcu_assign_pointer()
for the bat_priv->curr_gw need to be used, as well as spin/rcu locking.
Otherwise we might end up using a curr_gw pointer pointing to already
freed memory.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Batman-adv could receive several payload broadcasts at the same time
that would trigger access to the broadcast seqno sliding window to
determine whether this is a new broadcast or not. If these incoming
broadcasts are accessing the sliding window simultaneously it could
be left in an inconsistent state. Therefore it is necessary to make
sure this access is atomic.
Reported-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
bonding / alternating candidates need to be secured by rcu locks
as well. This patch therefore converts the bonding list
from a plain pointer list to a rcu securable lists and references
the bonding candidates.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
hardif_disable_interface() calls purge_orig_ref() to immediately free
all neighbors associated with the interface that is going down.
purge_orig_neighbors() checked if the interface status is IF_INACTIVE
which is set to IF_NOT_IN_USE shortly before calling purge_orig_ref().
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Remove duplicate inclusion of "send.h" and "routing.h" from
net/batman-adv/soft-interface.c
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
For a host in the mesh network, the batman layer should be transparent.
However, we had one exception, data packets within the mesh network
which have the same destination as a originator are being routed to
that node, although there is no host that node's bat0 interface and
therefore gets dropped anyway. This commit removes this exception.
Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
types.h is included by main.h, which is included at the beginning of any
other c-file anyway. Therefore this commit removes those duplicate
inclussions.
Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Multiple variable declarations in a single statements over multiple lines can
be split into multiple variable declarations without changing the actual
behavior.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The two fragments of an unicast packet must have successive sequence numbers to
allow the receiver side to detect matching fragments and merge them again. The
current implementation doesn't provide that property because a sequence of two
atomic_inc_return may be interleaved with another sequence which also changes
the variable.
The access to the fragment sequence number pool has either to be protected by
correct locking or it has to reserve two sequence numbers in a single fetch.
The latter one can easily be done by increasing the value of the last used
sequence number by 2 in a single step. The generated window of two currently
unused sequence numbers can now be scattered across the two fragments.
Reported-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
We access the data inside the skbs of two fragments directly using memmove
during the merge. The data of the skb could span over multiple skb pages. An
direct access without knowledge about the pages would lead to an invalid memory
access.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[lindner_marek@yahoo.de: Move return from function to the end]
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batman_skb_recv can be defined in hard-interface.c as static because it is
never used outside of that file.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Some function parameters are obsolete now and can be removed.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The routing algorithm must be able to decide if a fragment can be merged with
the missing part and still be passed to a forwarding interface. The fragments
can only differ by one byte in case that the original payload had an uneven
length. In that situation the sender has to inform all possible receivers that
the tail is one byte longer using the flag UNI_FRAG_LARGETAIL.
The combination of UNI_FRAG_LARGETAIL and UNI_FRAG_HEAD flag makes it possible
to calculate the correct length for even and uneven sized payloads.
The original formula missed to add the unicast header at all and forgot to
remove the fragment header of the second fragment. This made the results highly
unreliable and only useful for machines with large differences between the
configured MTUs.
Reported-by: Russell Senior <russell@personaltelco.net>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The routing algorithm must know how large two fragments are to be able to
decide that it is safe to merge them or if it should resubmit without waiting
for the second part. When these two fragments have a too different size, it is
not possible to guess right in every situation.
The user could easily configure the MTU of the attached cards so that one
fragment is forwarded and the other one is added to the fragments table to wait
for the missing part.
For even sized packets, it is possible to split it so that the resulting
packages are equal sized by ignoring the old non-fragment header at the
beginning of the original packet.
This still creates different sized fragments for uneven sized packets.
Reported-by: Russell Senior <russell@personaltelco.net>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The batman-adv vis server has to a stack which stores all information
about packets which should be send later. This stack is protected
with a spinlock that is used to prevent concurrent write access to it.
The send_vis_packets function has to take all elements from the stack
and send them to other hosts over the primary interface. The send will
be initiated without the lock which protects the stack.
The implementation using list_for_each_entry_safe has the problem that
it stores the next element as "safe ptr" to allow the deletion of the
current element in the list. The list may be modified during the
unlock/lock pair in the loop body which may make the safe pointer
not pointing to correct next element.
It is safer to remove and use the first element from the stack until no
elements are available. This does not need reduntant information which
would have to be validated each time the lock was removed.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The free_info function will be called when no reference to the info
object exists anymore. It must be ensured that the allocated memory
gets freed and not only the elements which are managed by the info
object.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
A newly created vis info object must be removed when it couldn't be
added to the hash. The old_info which has to be replaced was already
removed and isn't related to the hash anymore.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The hash_iterate removal introduced a bug leading to a kernel panic when
fetching the vis data on a vis server. That commit forgot to rename one
variable name, which this commit fixes now.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Linux 2.6.21 defines different macros for __attribute__ which are also
used inside batman-adv. The next version of checkpatch.pl warns about
the usage of __attribute__((packed))).
Linux 2.6.33 defines an extra macro __always_unused which is used to
assist source code analyzers and can be used to removed the last
existing __attribute__ inside the source code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
There's a problem in net/batman-adv/unicast.c::frag_send_skb().
dev_alloc_skb() allocates memory and may fail, thus returning NULL. If
this happens we'll pass a NULL pointer on to skb_split() which in turn
hands it to skb_split_inside_header() from where it gets passed to
skb_put() that lets skb_tail_pointer() play with it and that function
dereferences it. And thus the bat dies.
While I was at it I also moved the call to dev_alloc_skb() above the
assignment to 'unicast_packet' since there's no reason to do that
assignment if the memory allocation fails.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
hna_local_fill_buffer must return the number of added hna entries and
not the last checked hash bucket.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
B.A.T.M.A.N. (better approach to mobile ad-hoc networking) is a routing
protocol for multi-hop ad-hoc mesh networks. The networks may be wired or
wireless. See http://www.open-mesh.org/ for more information and user space
tools.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sven Eckelmann