With a relocatable kernel that could reside at any place in memory, code
and data that has to stay below 2 GB needs special handling.
This patch introduces .dma sections for such text, data and ex_table.
The sections will be part of the decompressor kernel, so they will not
be relocated and stay below 2 GB. Their location is passed over to the
decompressed / relocated kernel via the .boot.preserved.data section.
The duald and aste for control register setup also need to stay below
2 GB, so move the setup code from arch/s390/kernel/head64.S to
arch/s390/boot/head.S. The duct and linkage_stack could reside above
2 GB, but their content has to be preserved for the decompresed kernel,
so they are also moved into the .dma section.
The start and end address of the .dma sections is added to vmcoreinfo,
for crash support, to help debugging in case the kernel crashed there.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With a relocatable kernel that could reside at any place in memory, the
current logic for allocating a kprobes insn_page does not work. The
GFP_DMA allocated buffer might be more than 2 GB away from the kernel.
Use a static buffer for the insn_page instead.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Clear current_kprobe and enable preemption in kprobe
even if pre_handler returns !0.
This simplifies function override using kprobes.
Jprobe used to require to keep the preemption disabled and
keep current_kprobe until it returned to original function
entry. For this reason kprobe_int3_handler() and similar
arch dependent kprobe handers checks pre_handler result
and exit without enabling preemption if the result is !0.
After removing the jprobe, Kprobes does not need to
keep preempt disabled even if user handler returns !0
anymore.
But since the function override handler in error-inject
and bpf is also returns !0 if it overrides a function,
to balancing the preempt count, it enables preemption
and reset current kprobe by itself.
That is a bad design that is very buggy. This fixes
such unbalanced preempt-count and current_kprobes setting
in kprobes, bpf and error-inject.
Note: for powerpc and x86, this removes all preempt_disable
from kprobe_ftrace_handler because ftrace callbacks are
called under preempt disabled.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: linux-arch@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-s390@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Link: https://lore.kernel.org/lkml/152942494574.15209.12323837825873032258.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Don't call the ->break_handler() from the s390 kprobes code,
because it was only used by jprobes which got removed.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-arch@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Link: https://lore.kernel.org/lkml/152942485849.15209.16608277783809018031.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove %p because the kprobe will be dumped in dump_kprobe().
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now that the SPDX tag is in all arch/s390/kernel/ files, that identifies
the license in a specific and legally-defined manner. So the extra GPL
text wording can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the arch/s390/kernel/ files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For an unknown reason the s390 kprobes instruction replacement
function modifies the kprobe_status of the current CPU to
KPROBE_SWAP_INST. This was supposed to catch traps that happened
during instruction patching. Such a fault is not supposed to happen,
and silently discarding such a fault is certainly also not what we
want. In fact s390 is the only architecture which has this odd piece
of code.
Just remove this and behave like all other architectures. This was
pointed out by Jens Remus.
Reported-by: Jens Remus <jremus@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The text patching functions which are invoked from jump_label and kprobes
code are protected against cpu hotplug at the call sites.
Use stop_machine_cpuslocked() to avoid recursion on the cpu hotplug
rwsem. stop_machine_cpuslocked() contains a lockdep assertion to catch any
unprotected callers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20170524081549.354513406@linutronix.de
set_memory_* functions have moved to set_memory.h. Switch to this
explicitly
Link: http://lkml.kernel.org/r/1488920133-27229-5-git-send-email-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bit 0x100 of a page table, segment table of region table entry
can be used to disallow code execution for the virtual addresses
associated with the entry.
There is one tricky bit, the system call to return from a signal
is part of the signal frame written to the user stack. With a
non-executable stack this would stop working. To avoid breaking
things the protection fault handler checks the opcode that caused
the fault for 0x0a77 (sys_sigreturn) and 0x0aad (sys_rt_sigreturn)
and injects a system call. This is preferable to the alternative
solution with a stub function in the vdso because it works for
vdso=off and statically linked binaries as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These files were only including module.h for exception table
related functions. We've now separated that content out into its
own file "extable.h" so now move over to that and avoid all the
extra header content in module.h that we don't really need to compile
these files.
The additions of uaccess.h are to deal with implict includes like:
arch/s390/kernel/traps.c: In function 'do_report_trap':
arch/s390/kernel/traps.c:56:4: error: implicit declaration of function 'extable_fixup' [-Werror=implicit-function-declaration]
arch/s390/kernel/traps.c: In function 'illegal_op':
arch/s390/kernel/traps.c:173:3: error: implicit declaration of function 'get_user' [-Werror=implicit-function-declaration]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This fixes the same issue Steven already fixed for x86
in following commit:
237d28db03 ftrace/jprobes/x86: Fix conflict between jprobes and function graph tracing
It fixes the crash, that happens when function graph tracing
and jprobes are used simultaneously. Please refer to above
commit for details.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Yet another leftover from the 31 bit era. The usual operation
"y = x & PSW_ADDR_INSN" with the PSW_ADDR_INSN mask is a nop for
CONFIG_64BIT.
Therefore remove all usages and hope the code is a bit less confusing.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
This is a leftover from the 31 bit area. For CONFIG_64BIT the usual
operation "y = x | PSW_ADDR_AMODE" is a nop. Therefore remove all
usages of PSW_ADDR_AMODE and make the code a bit less confusing.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Remove the s390 architecture implementation of probe_kernel_write() and
instead use a new function s390_kernel_write() to modify kernel text and
data everywhere.
The s390 implementation of probe_kernel_write() was potentially broken
since it modified memory in a read-modify-write fashion, which read four
bytes, modified the requested bytes within those four bytes and wrote
the result back.
If two cpus would modify the same four byte area at different locations
within that area, this could lead to corruption.
Right now the only places which called probe_kernel_write() did run within
stop_machine_run. Therefore the scenario can't happen right now, however
that might change at any time.
To fix this rename probe_kernel_write() to s390_kernel_write() which can
have special semantics, like only call it while running within stop_machine().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make use of gcc's hotpatch support to generate better code for ftrace
function tracing.
The generated code now contains only a six byte nop in each function
prologue instead of a 24 byte code block which will be runtime patched to
support function tracing.
With the new code generation the runtime overhead for supporting function
tracing is close to zero, while the original code did show a significant
performance impact.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When we generate the instruction for out of line execution the length
of the to be copied instruction was evaluated from a not initialized
memory location.
Therefore we ended up with a random (2, 4 or 6) number of bytes being
copied instead of taking the real instruction length into account.
This works surprisingly well most of the time, but still not always.
Reported-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use NOKPROBE_SYMBOL() instead of __kprobes annotation.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the function tracer is enabled, allow to set kprobes on the first
instruction of a function (which is the function trace caller):
If no kprobe is set handling of enabling and disabling function tracing
of a function simply patches the first instruction. Either it is a nop
(right now it's an unconditional branch, which skips the mcount block),
or it's a branch to the ftrace_caller() function.
If a kprobe is being placed on a function tracer calling instruction
we encode if we actually have a nop or branch in the remaining bytes
after the breakpoint instruction (illegal opcode).
This is possible, since the size of the instruction used for the nop
and branch is six bytes, while the size of the breakpoint is only
two bytes.
Therefore the first two bytes contain the illegal opcode and the last
four bytes contain either "0" for nop or "1" for branch. The kprobes
code will then execute/simulate the correct instruction.
Instruction patching for kprobes and function tracer is always done
with stop_machine(). Therefore we don't have any races where an
instruction is patched concurrently on a different cpu.
Besides that also the program check handler which executes the function
trace caller instruction won't be executed concurrently to any
stop_machine() execution.
This allows to keep full fault based kprobes handling which generates
correct pt_regs contents automatically.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
This patch moves common functions from kprobes.c to probes.c.
Thus its possible for uprobes to use them without enabling kprobes.
Signed-off-by: Jan Willeke <willeke@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Even if it has a __used annotation it is actually unused.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.
The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e. using a global
register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
this_cpu_inc(y)
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: linux390@de.ibm.com
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Since we have an in-kernel disassembler we can make sure that
there won't be any kprobes set on random data.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When checking the insn address wether it is a kernel image or module
address it should be an if-else-if statement not two independent if
statements.
This doesn't really fix a bug, but matches s390_free_insn_slot().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
"execute relative long" may have all sorts of side effects dependend on
the instructions it executes.
Therefore prohibit setting a kprobe on exrl just like we do for the
regular execute instruction.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With the general-instruction extension facility (z10) a couple of
instructions with a pc-relative long displacement were introduced. The
kprobes support for these instructions however was never implemented.
In result, if anybody ever put a probe on any of these instructions the
result would have been random behaviour after the instruction got executed
within the insn slot.
So lets add the missing handling for these instructions. Since all of the
new instructions have 32 bit signed displacement the easiest solution is
to allocate an insn slot that is within the same 2GB area like the
original instruction and patch the displacement field.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compare and branch instructions (not relative) all need special
handling when kprobed:
- if a branch was taken, the instruction pointer should be left alone
- if a branch was not taken, the instruction pointer must be adjusted
The compare and branch instructions family was introduced with the general
instruction extension facility (z10).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the s390 port of 70627654 "x86, extable: Switch to relative
exception table entries".
Reduces the size of our exception tables by 50% on 64 bit builds.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Restructure the kprobe breakpoint handler function. Add comments to
make it more comprehensible and add a sanity check for re-entering
kprobes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Register %r14 and %r15 are already stored in jprobe_saved_regs, no need
to store them a second time in jprobe_saved_r14 / jprobe_saved_r15.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 architecture can execute code on kmalloc/vmalloc memory.
No need for the __ARCH_WANT_KPROBES_INSN_SLOT detour.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace set_current_kprobe/reset_current_kprobe/save_previous_kprobe/
restore_previous_kprobe with a simpler scheme push_kprobe/pop_kprobe.
The mini kprobes stack can store up to two active kprobes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Determine instruction fixup details in resume_execution, no need to do
it beforehand. Remove fixup, ilen and reg from arch_specific_insn.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the definition of the helper structure ins_replace_args to the
only place where it is used and drop the old member as it is not needed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The saved interrupt mask and the saved control registers are only
relevant while single stepping is set up. A secondary kprobe while
kprobe single stepping is active may not occur. That makes is safe
to remove the save and restore of kprobe_saved_imask / kprobe_save_ctl
from save_previous_kprobe and restore_previous_kprobe.
Move all single step related code to two functions, enable_singlestep
and disable_singlestep.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove special case of a kprobe on a breakpoint while a relocated
instruction is single stepped. The only instruction that may cause
a fault while kprobe single stepping is active is the relocated
instruction. There is no kprobe on the instruction slot retrieved
with get_insn_slot().
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Analog to git commit 737480a0d5
fix the return address of subsequent kretprobes when multiple
kretprobes are set on the same function.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Gerald Schaefer