Just four simple fixes this week:
- one missing of_node_put() on armv7 based mvebu
- forcing the USB host into the right mode on Chromebook (exynos5-snow)
- enabling two important drivers for exynos_defconfig
- fixing a noncritical bug for tegra that would cause a
regression with common code patches queued for 3.19
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=68UY
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Not much interesting going on fixes-wise for us this week, as it
should be for an -rc7. I'm not expecting Olof to work much over
Thanksgiving weekend, so I decided to take over again and push these
out to you.
Just four simple fixes this week:
- one missing of_node_put() on armv7 based mvebu
- forcing the USB host into the right mode on Chromebook
(exynos5-snow)
- enabling two important drivers for exynos_defconfig
- fixing a noncritical bug for tegra that would cause a regression
with common code patches queued for 3.19"
* tag 'armsoc-for-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: irq: fix buggy usage of irq_data irq field
ARM: exynos_defconfig: Enable max77802 rtc and clock drivers
ARM: dts: Explicitly set dr_mode on exynos5250-snow
ARM: mvebu: add missing of_node_put() call in coherency.c
Pull ARM fixes from Russell King:
"Another round of relatively small ARM fixes.
Thomas spotted that the strex backoff delay bit was a disable bit, so
it needed to be clear for this to work. Vladimir spotted that using a
restart block for the cache flush operation would return -EINTR, which
userspace was not expecting. Dmitry spotted that the auxiliary
control register accesses for Xscale were not correct"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8226/1: cacheflush: get rid of restarting block
ARM: 8222/1: mvebu: enable strex backoff delay
ARM: 8216/1: xscale: correct auxiliary register in suspend/resume
Pull mips fixes from Ralf Baechle:
"The hopefully final round of fixes for 3.18:
- Fix a number of build errors affecting particular configurations.
- Handle EVA correctly when flushing a signal trampoline and dcache
lines.
- Fix printks printing jibberish.
- Handle 64 bit memory addresses correctly when adding memory chunk
on 32 bit kernels.
- Fix a race condition in the hardware tablewalker code"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: tlbex: Fix potential HTW race on TLBL/M/S handlers
MIPS: Fix address type used for early memory detection.
MIPS: Kconfig: Don't allow both microMIPS and SmartMIPS to be selected.
MIPS: kernel: cps-vec: Set ISA level to mips32r2 for the MIPS MT ASE
MIPS: Netlogic: handle modular AHCI builds
MIPS: Netlogic: handle modular USB case
MIPS: Loongson: Make platform serial setup always built-in.
MIPS: fix EVA & non-SMP non-FPU FP context signal handling
MIPS: cpu-probe: Set the FTLB probability bit on supported cores
MIPS: BMIPS: Fix ".previous without corresponding .section" warnings
MIPS: uaccess.h: Fix strnlen_user comment.
MIPS: r4kcache: Add EVA case for protected_writeback_dcache_line
MIPS: Fix info about plat_setup in arch_mem_init comment
MIPS: rtlx: Remove KERN_DEBUG from pr_debug() arguments in rtlx.c
MIPS: SEAD3: Fix LED device registration.
MIPS: Fix a copy & paste error in unistd.h
Pull powerpc fixes from Michael Ellerman:
"Here are five fixes for you to pull please.
They're all CC'ed to stable except the "Fix PE state format" one which
went in this release"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc: 32 bit getcpu VDSO function uses 64 bit instructions
powerpc/powernv: Replace OPAL_DEASSERT_RESET with EEH_RESET_DEACTIVATE
powerpc/eeh: Fix PE state format
powerpc/pseries: Fix endiannes issue in RTAS call from xmon
powerpc/powernv: Fix the hmi event version check.
Pull sparc fixlet from David Miller:
"Aparc fix to add dma_cache_sync(), even if a nop it should be provided
if dma_{alloc,free}_noncoherent() is provided too"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Add NOP dma_cache_sync() implementation.
There is a potential race when probing the TLB in TLBL/M/S exception
handlers for a matching entry. Between the time we hit a TLBL/S/M
exception and the time we get to execute the TLBP instruction, the
HTW may have replaced the TLB entry we are interested in hence the TLB
probe may fail. However, in the existing handlers, we never checked the
status of the TLBP (ie check the result in the C0/Index register). We
fix this by adding such a check when the core implements the HTW. If
we couldn't find a matching entry, we return back and try again.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.17+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8599/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We cannot restart cacheflush safely if a process provides user-defined
signal handler and signal is pending. In this case -EINTR is returned
and it is expected that process re-invokes syscall. However, there are
a few problems with that:
* looks like nobody bothers checking return value from cacheflush
* but if it did, we don't provide the restart address for that, so the
process has to use the same range again
* ...and again, what might lead to looping forever
So, remove cacheflush restarting code and terminate cache flushing
as early as fatal signal is pending.
Cc: stable@vger.kernel.org # 3.12+
Reported-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Under extremely rare conditions, in an MPCore node consisting of at
least 3 CPUs, two CPUs trying to perform a STREX to data on the same
shared cache line can enter a livelock situation.
This patch enables the HW mechanism that overcomes the bug. This fixes
the incorrect setup of the STREX backoff delay bit due to a wrong
description in the specification.
Note that enabling the STREX backoff delay mechanism is done by
leaving the bit *cleared*, while the bit was currently being set by
the proc-v7.S code.
[Thomas: adapt to latest mainline, slightly reword the commit log, add
stable markers.]
Fixes: de4901933f ("arm: mm: Add support for PJ4B cpu and init routines")
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- enable max77802 rtc and clock drivers for exynos_defconfig
: enable the kernel config options to have the drivers for
max77802 including rtc and 2-ch 32kHz clock outputs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gg9h
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull "Samsung defconfig update for v3.18" from Kukjin Kim:
- enable max77802 rtc and clock drivers for exynos_defconfig
: enable the kernel config options to have the drivers for
max77802 including rtc and 2-ch 32kHz clock outputs
* tag 'samsung-defconfig-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: Enable max77802 rtc and clock drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- explicitly set dr_mode on exynos5250-snow
this is required when kernel is built with USB gadget support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=R/UY
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull "Samsung fixes for v3.18" from Kukjin Kim:
- explicitly set dr_mode on exynos5250-snow
this is required when kernel is built with USB gadget support.
* tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5250-snow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The crazy gic_arch_extn thing that Tegra uses contains multiple
references to the irq field in struct irq_data, and uses this
to directly poke hardware register.
But irq is the *virtual* irq number, something that has nothing
to do with the actual HW irq (stored in the hwirq field). And once
we put the stacked domain code in action, the whole thing explodes,
as these two values are *very* different:
root@bacon-fat:~# cat /proc/interrupts
CPU0 CPU1
16: 25801 2075 GIC 29 twd
17: 0 0 GIC 73 timer0
112: 0 0 GPIO 58 c8000600.sdhci cd
123: 0 0 GPIO 69 c8000200.sdhci cd
279: 1126 0 GIC 122 serial
281: 0 0 GIC 70 7000c000.i2c
282: 0 0 GIC 116 7000c400.i2c
283: 0 0 GIC 124 7000c500.i2c
284: 300 0 GIC 85 7000d000.i2c
[...]
Just replacing all instances of irq with hwirq fixes the issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I used some 64 bit instructions when adding the 32 bit getcpu VDSO
function. Fix it.
Fixes: 18ad51dd34 ("powerpc: Add VDSO version of getcpu")
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The flag passed to ioda_eeh_phb_reset() should be EEH_RESET_DEACTIVATE,
which is translated to OPAL_DEASSERT_RESET or something else by the
EEH backend accordingly.
The patch replaces OPAL_DEASSERT_RESET with EEH_RESET_DEACTIVATE for
ioda_eeh_phb_reset().
Cc: stable@vger.kernel.org
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Obviously I had wrong format given to the PE state output from
/sys/bus/pci/devices/xxxx/eeh_pe_state with some typoes, which
was introduced by commit 2013add4ce. The patch fixes it up.
Fixes: 2013add4ce ("powerpc/eeh: Show hex prefix for PE state sysfs")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On pseries system (LPAR) xmon failed to enter when running in LE mode,
system is hunging. Inititating xmon will lead to such an output on the
console:
SysRq : Entering xmon
cpu 0x15: Vector: 0 at [c0000003f39ffb10]
pc: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
lr: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
sp: c0000003f39ffc70
msr: 8000000000009033
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
Bad kernel stack pointer fafb4b0 at eca7cc4
cpu 0x15: Vector: 300 (Data Access) at [c000000007f07d40]
pc: 000000000eca7cc4
lr: 000000000eca7c44
sp: fafb4b0
msr: 8000000000001000
dar: 10000000
dsisr: 42000000
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
cpu 0x15: Exception 300 (Data Access) in xmon, returning to main loop
xmon: WARNING: bad recursive fault on cpu 0x15
The root cause is that xmon is calling RTAS to turn off the surveillance
when entering xmon, and RTAS is requiring big endian parameters.
This patch is byte swapping the RTAS arguments when running in LE mode.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current HMI event structure is an ABI and carries a version field to
accommodate future changes without affecting/rearranging current structure
members that are valid for previous versions.
The current version check "if (hmi_evt->version != OpalHMIEvt_V1)"
doesn't accomodate the fact that the version number may change in
future.
If firmware starts returning an HMI event with version > 1, this check
will fail and no HMI information will be printed on older kernels.
This patch fixes this issue.
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
[mpe: Reword changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 85c8555ff0 ("KVM: check for !is_zero_pfn() in
kvm_is_mmio_pfn()") and renames the function to kvm_is_reserved_pfn.
The problem being addressed by the patch above was that some ARM code
based the memory mapping attributes of a pfn on the return value of
kvm_is_mmio_pfn(), whose name indeed suggests that such pfns should
be mapped as device memory.
However, kvm_is_mmio_pfn() doesn't do quite what it says on the tin,
and the existing non-ARM users were already using it in a way which
suggests that its name should probably have been 'kvm_is_reserved_pfn'
from the beginning, e.g., whether or not to call get_page/put_page on
it etc. This means that returning false for the zero page is a mistake
and the patch above should be reverted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of using kvm_is_mmio_pfn() to decide whether a host region
should be stage 2 mapped with device attributes, add a new static
function kvm_is_device_pfn() that disregards RAM pages with the
reserved bit set, as those should usually not be mapped as device
memory.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When running on a system with a GICv3, we currenly don't allow the guest
to access the system register interface of the GICv3. We do this by
clearing the ICC_SRE_EL2.Enable, which causes all guest accesses to
ICC_SRE_EL1 to trap to EL2 and causes all guest accesses to other ICC_
registers to cause an undefined exception in the guest.
However, we currently don't handle the trap of guest accesses to
ICC_SRE_EL1 and will spill out a warning. The trap just needs to handle
the access as RAZ/WI, and a guest that tries to prod this register and
set ICC_SRE_EL1.SRE=1, must read back the value (which Linux already
does) to see if it succeeded, and will thus observe that ICC_SRE_EL1.SRE
was not set.
Add the simple trap handler in the sorted table of the system registers.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
[ardb: added cp15 handling]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In 'early_parse_mem' the data type used for the start
and size of a memory region specified on the command line
is incorrect. If 64-bit addressing is used, the value
gets truncated.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8456/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
microMIPS and SmartMIPS can't be used together. This fixes the
following build problem:
Warning: the 32-bit microMIPS architecture does not support the `smartmips' extension
arch/mips/kernel/entry.S:90: Error: unrecognized opcode `mtlhx $24'
[...]
arch/mips/kernel/entry.S:109: Error: unrecognized opcode `mtlhx $24'
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7421/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commits a951440971 ("MIPS: Netlogic: Support for XLP3XX on-chip SATA")
and fedfcb1137 ("MIPS: Netlogic: XLP9XX on-chip SATA support") added
ahci-init and ahci-init-xlp2 as objects to build when CONFIG_SATA_AHCI
is enabled.
If CONFIG_SATA_AHCI is made modular, these two files will also get built
as modules (obj-m), which will result in the following linking failure:
ERROR: "nlm_set_pic_extra_ack" [arch/mips/netlogic/xlp/ahci-init.ko]
undefined!
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/ahci-init.ko] undefined!
ERROR: "nlm_nodes" [arch/mips/netlogic/xlp/ahci-init-xlp2.ko] undefined!
ERROR: "nlm_set_pic_extra_ack"
[arch/mips/netlogic/xlp/ahci-init-xlp2.ko] undefined!
ERROR: "xlp_socdev_to_node" [arch/mips/netlogic/xlp/ahci-init-xlp2.ko]
undefined!
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/ahci-init-xlp2.ko]
undefined!
Just check whether CONFIG_SATA_AHCI is defined for this build, and if
that is the case, add these objects to the list of built-in object
files.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: ganesanr@broadcom.com
Cc: jchandra@broadcom.com
Patchwork: https://patchwork.linux-mips.org/patch/7855/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1004165f34 ("MIPS: Netlogic: USB support for XLP") and then
commit 9eac3591e7 ("MIPS: Netlogic: Add support for USB on XLP2xx")
added usb-init and usb-init-xlp2 as objects to build when CONFIG_USB is
enabled.
If CONFIG_USB is made modular, these two files will also get built as
modules (obj-m), which will result in the following linking failure:
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/usb-init.ko] undefined!
ERROR: "nlm_nodes" [arch/mips/netlogic/xlp/usb-init-xlp2.ko] undefined!
ERROR: "nlm_set_pic_extra_ack" [arch/mips/netlogic/xlp/usb-init-xlp2.ko]
undefined!
ERROR: "xlp_socdev_to_node" [arch/mips/netlogic/xlp/usb-init-xlp2.ko]
undefined!
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/usb-init-xlp2.ko]
undefined!
Just check whether CONFIG_USB is defined for this build, and if that is
the case, add these objects to the list of built-in object files.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: ganesanr@broadcom.com
Cc: jchandra@broadcom.com
Patchwork: https://patchwork.linux-mips.org/patch/7854/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If SERIAL_8250 is compiled as a module, the platform specific setup
for Loongson will be a module too, and it will not work very well.
At least on Loongson 3 it will trigger a build failure,
since loongson_sysconf is not exported to modules.
Fix by making the platform specific serial code always built-in.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Ralf Baechle <ralf@linux-mips.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Markos Chandras <Markos.Chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/8533/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The save_fp_context & restore_fp_context pointers were being assigned
to the wrong variables if either:
- The kernel is configured for UP & runs on a system without an FPU,
since b2ead52828 "MIPS: Move & rename
fpu_emulator_{save,restore}_context".
- The kernel is configured for EVA, since ca750649e0 "MIPS: kernel:
signal: Prevent save/restore FPU context in user memory".
This would lead to FP context being clobbered incorrectly when setting
up a sigcontext, then the garbage values being saved uselessly when
returning from the signal.
Fix by swapping the pointer assignments appropriately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: stable@vger.kernel.org # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8230/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the Config6/FLTBP bit to set the probability of a TLBWR
instruction to hit the FTLB or the VTLB. A value of 0 (which may be
the default value on certain cores, such as proAptiv or P5600)
means that a TLBWR instruction will never hit the VTLB which
leads to performance limitations since it effectively decreases
the number of available TLB slots.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8368/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit de8974e3f7 ("MIPS: asm: r4kcache: Add EVA cache flushing
functions") added cache function for EVA using the cachee instruction.
However, it didn't add a case for the protected_writeback_dcache_line.
mips_dsemul() calls r4k_flush_cache_sigtramp() which in turn uses
the protected_writeback_dcache_line() to flush the trampoline code
back to memory. This used the wrong "cache" instruction leading to
random userland crashes on non-FPU cores.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8331/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is now fully replaced with the generic "no_64bit_msi" one
that is set by the respective drivers directly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead of the arch specific quirk which we are deprecating
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Instead of the arch specific quirk which we are deprecating
and that drivers don't understand.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
x86 call do_notify_resume on paranoid returns if TIF_UPROBE is set but
not on non-paranoid returns. I suspect that this is a mistake and that
the code only works because int3 is paranoid.
Setting _TIF_NOTIFY_RESUME in the uprobe code was probably a workaround
for the x86 bug. With that bug fixed, we can remove _TIF_NOTIFY_RESUME
from the uprobes code.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge x86-64 iret fixes from Andy Lutomirski:
"This addresses the following issues:
- an unrecoverable double-fault triggerable with modify_ldt.
- invalid stack usage in espfix64 failed IRET recovery from IST
context.
- invalid stack usage in non-espfix64 failed IRET recovery from IST
context.
It also makes a good but IMO scary change: non-espfix64 failed IRET
will now report the correct error. Hopefully nothing depended on the
old incorrect behavior, but maybe Wine will get confused in some
obscure corner case"
* emailed patches from Andy Lutomirski <luto@amacapital.net>:
x86_64, traps: Rework bad_iret
x86_64, traps: Stop using IST for #SS
x86_64, traps: Fix the espfix64 #DF fixup and rewrite it in C
It's possible for iretq to userspace to fail. This can happen because
of a bad CS, SS, or RIP.
Historically, we've handled it by fixing up an exception from iretq to
land at bad_iret, which pretends that the failed iret frame was really
the hardware part of #GP(0) from userspace. To make this work, there's
an extra fixup to fudge the gs base into a usable state.
This is suboptimal because it loses the original exception. It's also
buggy because there's no guarantee that we were on the kernel stack to
begin with. For example, if the failing iret happened on return from an
NMI, then we'll end up executing general_protection on the NMI stack.
This is bad for several reasons, the most immediate of which is that
general_protection, as a non-paranoid idtentry, will try to deliver
signals and/or schedule from the wrong stack.
This patch throws out bad_iret entirely. As a replacement, it augments
the existing swapgs fudge into a full-blown iret fixup, mostly written
in C. It's should be clearer and more correct.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a 32-bit kernel, this has no effect, since there are no IST stacks.
On a 64-bit kernel, #SS can only happen in user code, on a failed iret
to user space, a canonical violation on access via RSP or RBP, or a
genuine stack segment violation in 32-bit kernel code. The first two
cases don't need IST, and the latter two cases are unlikely fatal bugs,
and promoting them to double faults would be fine.
This fixes a bug in which the espfix64 code mishandles a stack segment
violation.
This saves 4k of memory per CPU and a tiny bit of code.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's nothing special enough about the espfix64 double fault fixup to
justify writing it in assembly. Move it to C.
This also fixes a bug: if the double fault came from an IST stack, the
old asm code would return to a partially uninitialized stack frame.
Fixes: 3891a04aaf
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A collection of fixes this week:
- A set of clock fixes for shmobile platforms
- A fix for tegra that moves serial port labels to be per board.
We're choosing to merge this for 3.18 because the labels will start
being parsed in 3.19, and without this change serial port numbers that
used to be stable since the dawn of time will change numbers.
- A few other DT tweaks for Tegra.
- A fix for multi_v7_defconfig that makes it stop spewing cpufreq errors on
Arndale (Exynos).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FXz0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes this week:
- A set of clock fixes for shmobile platforms
- A fix for tegra that moves serial port labels to be per board.
We're choosing to merge this for 3.18 because the labels will start
being parsed in 3.19, and without this change serial port numbers
that used to be stable since the dawn of time will change numbers.
- A few other DT tweaks for Tegra.
- A fix for multi_v7_defconfig that makes it stop spewing cpufreq
errors on Arndale (Exynos)"
* tag 'armsoc-for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: fix failure setting CPU voltage by enabling dependent I2C controller
ARM: tegra: roth: Fix SD card VDD_IO regulator
ARM: tegra: Remove eMMC vmmc property for roth/tn7
ARM: dts: tegra: move serial aliases to per-board
ARM: tegra: Add serial port labels to Tegra124 DT
ARM: shmobile: kzm9g legacy: Set i2c clks_per_count to 2
ARM: shmobile: r8a7740 dtsi: Correct IIC0 parent clock
ARM: shmobile: r8a7790: Fix SD3CKCR address to device tree
ARM: shmobile: r8a7740 legacy: Correct IIC0 parent clock
ARM: shmobile: r8a7740 legacy: Add missing INTCA clock for irqpin module
ARM: shmobile: r8a7790: Fix SD3CKCR address
ARM: dts: sun6i: Re-parent ahb1_mux to pll6 as required by dma controller
Pull MIPS fixes from Ralf Baechle:
"More 3.18 fixes for MIPS:
- backtraces were not quite working on on 64-bit kernels
- loongson needs a different cache coherency setting
- Loongson 3 is a MIPS64 R2 version but due to erratum we treat is an
older architecture revision.
- fix build errors due to undefined references to __node_distances
for certain configurations.
- fix instruction decodig in the jump label code.
- for certain configurations copy_{from,to}_user destroy the content
of $3 so that register needs to be marked as clobbed by the calling
code.
- Hardware Table Walker fixes.
- fill the delay slot of the last instruction of memcpy otherwise
whatever ends up there randomly might have undesirable effects.
- ensure get_user/__get_user always zero the variable to be read even
in case of an error"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: jump_label.c: Handle the microMIPS J instruction encoding
MIPS: jump_label.c: Correct the span of the J instruction
MIPS: Zero variable read by get_user / __get_user in case of an error.
MIPS: lib: memcpy: Restore NOP on delay slot before returning to caller
MIPS: tlb-r4k: Add missing HTW stop/start sequences
MIPS: asm: uaccess: Add v1 register to clobber list on EVA
MIPS: oprofile: Fix backtrace on 64-bit kernel
MIPS: Loongson: Set Loongson-3's ISA level to MIPS64R1
MIPS: Loongson: Fix the write-combine CCA value setting
MIPS: IP27: Fix __node_distances undefined error
MIPS: Loongson3: Fix __node_distances undefined error
Pull powerpc fix from Michael Ellerman:
"One fix from Scott, he says:
This patch fixes a crash (introduced in v3.18-rc1) in the FSL MSI driver
when threaded IRQs are enabled"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/fsl_msi: mark the msi cascade handler IRQF_NO_THREAD
Pull x86 fixes from Thomas Gleixner:
"Misc fixes:
- gold linker build fix
- noxsave command line parsing fix
- bugfix for NX setup
- microcode resume path bug fix
- _TIF_NOHZ versus TIF_NOHZ bugfix as discussed in the mysterious
lockup thread"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, syscall: Fix _TIF_NOHZ handling in syscall_trace_enter_phase1
x86, kaslr: Handle Gold linker for finding bss/brk
x86, mm: Set NX across entire PMD at boot
x86, microcode: Update BSPs microcode on resume
x86: Require exact match for 'noxsave' command line option
Pull perf fixes from Ingo Molnar:
"Misc fixes: two Intel uncore driver fixes, a CPU-hotplug fix and a
build dependencies fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Fix boot crash on SBOX PMU on Haswell-EP
perf/x86/intel/uncore: Fix IRP uncore register offsets on Haswell EP
perf: Fix corruption of sibling list with hotplug
perf/x86: Fix embarrasing typo
Linus Torvalds