The SGI Altix UV2 BAU (Broadcast Assist Unit) as used for
tlb-shootdown (selective broadcast mode) always uses UV2
broadcast descriptor format. There is no need to clear the
'legacy' (UV1) mode, because the hardware always uses UV2 mode
for selective broadcast.
But the BIOS uses general broadcast and legacy mode, and the
hardware pays attention to the legacy mode bit for general
broadcast. So the kernel must not clear that mode bit.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/E1SccoO-0002Lh-Cb@eag09.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Current cpu_mask_to_apicid() and cpu_mask_to_apicid_and()
implementations have few shortcomings:
1. A value returned by cpu_mask_to_apicid() is written to
hardware registers unconditionally. Should BAD_APICID get ever
returned it will be written to a hardware too. But the value of
BAD_APICID is not universal across all hardware in all modes and
might cause unexpected results, i.e. interrupts might get routed
to CPUs that are not configured to receive it.
2. Because the value of BAD_APICID is not universal it is
counter- intuitive to return it for a hardware where it does not
make sense (i.e. x2apic).
3. cpu_mask_to_apicid_and() operation is thought as an
complement to cpu_mask_to_apicid() that only applies a AND mask
on top of a cpumask being passed. Yet, as consequence of 18374d8
commit the two operations are inconsistent in that of:
cpu_mask_to_apicid() should not get a offline CPU with the cpumask
cpu_mask_to_apicid_and() should not fail and return BAD_APICID
These limitations are impossible to realize just from looking at
the operations prototypes.
Most of these shortcomings are resolved by returning a error
code instead of BAD_APICID. As the result, faults are reported
back early rather than possibilities to cause a unexpected
behaviour exist (in case of [1]).
The only exception is setup_timer_IRQ0_pin() routine. Although
obviously controversial to this fix, its existing behaviour is
preserved to not break the fragile check_timer() and would
better addressed in a separate fix.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/20120607131559.GF4759@dhcp-26-207.brq.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The allmodconfig hits:
WARNING: vmlinux.o(.text+0x6553d): Section mismatch in
reference from the function intel_scu_devices_create() to the
function .devinit.text: spi_register_board_info()
[...]
This patch marks intel_scu_devices_create() as devinit because
it only calls a devinit function, spi_register_board_info().
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Link: http://lkml.kernel.org/r/20120531212025.GA8519@breakpoint.cc
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Other than ix86, x86-64 on EFI so far didn't set the
{g,s}et_wallclock accessors to the EFI routines, thus
incorrectly using raw RTC accesses instead.
Simply removing the #ifdef around the respective code isn't
enough, however: While so far early get-time calls were done in
physical mode, this doesn't work properly for x86-64, as virtual
addresses would still need to be set up for all runtime regions
(which wasn't the case on the system I have access to), so
instead the patch moves the call to efi_enter_virtual_mode()
ahead (which in turn allows to drop all code related to calling
efi-get-time in physical mode).
Additionally the earlier calling of efi_set_executable()
requires the CPA code to cope, i.e. during early boot it must be
avoided to call cpa_flush_array(), as the first thing this
function does is a BUG_ON(irqs_disabled()).
Also make the two EFI functions in question here static -
they're not being referenced elsewhere.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4FBFBF5F020000780008637F@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The interrupt chip irq_set_affinity() functions copy the affinity mask
to irq_data->affinity but return 0, i.e. IRQ_SET_MASK_OK.
IRQ_SET_MASK_OK causes the core code to do another redundant copy.
Return IRQ_SET_MASK_OK_NOCOPY to avoid this.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Cliff Wickman <cpw@sgi.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Keping Chen <chenkeping@huawei.com>
Link: http://lkml.kernel.org/r/1333120296-13563-4-git-send-email-jiang.liu@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull x86 platform changes from Ingo Molnar:
"This tree includes assorted platform driver updates and a preparatory
series for a platform with custom DMA remapping semantics (sta2x11 I/O
hub)."
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vsmp: Fix number of CPUs when vsmp is disabled
keyboard: Use BIOS Keyboard variable to set Numlock
x86/olpc/xo1/sci: Report RTC wakeup events
x86/olpc/xo1/sci: Produce wakeup events for buttons and switches
x86, platform: Initial support for sta2x11 I/O hub
x86: Introduce CONFIG_X86_DMA_REMAP
x86-32: Introduce CONFIG_X86_DEV_DMA_OPS
It seems that there was an error with the active_low = 1 for the
LED, since it should be set to 0 (meaning that active is high,
since 0 is false, hence the confusion.
The wiki article about it confuses it, since it contradicts itself,
regarding what turns on the LED.
I have tested 3.4-rc2 on my net5501 with this patch, and it makes the LED
behave correctly, where "none" turns it off, and "default-on" turns it on,
when echoed onto the trigger "file" in /sys/class/leds.
Signed-off-by: Bjarke Istrup Pedersen <gurligebis@gentoo.org>
Link: http://lkml.kernel.org/r/20120504210146.62186A018B@akpm.mtv.corp.google.com
Cc: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The second parameter to intel_scu_notifier_post is a void *, not
an integer.
This quiets the sparse noise:
arch/x86/platform/mrst/mrst.c:808:48: warning: Using plain integer as NULL pointer
arch/x86/platform/mrst/mrst.c:817:43: warning: Using plain integer as NULL pointer
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/201204241500.53685.hartleys@visionengravers.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 updates from Ingo Molnar.
This touches some non-x86 files due to the sanitized INLINE_SPIN_UNLOCK
config usage.
Fixed up trivial conflicts due to just header include changes (removing
headers due to cpu_idle() merge clashing with the <asm/system.h> split).
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/amd: Be more verbose about LVT offset assignments
x86, tls: Off by one limit check
x86/ioapic: Add io_apic_ops driver layer to allow interception
x86/olpc: Add debugfs interface for EC commands
x86: Merge the x86_32 and x86_64 cpu_idle() functions
x86/kconfig: Remove CONFIG_TR=y from the defconfigs
x86: Stop recursive fault in print_context_stack after stack overflow
x86/io_apic: Move and reenable irq only when CONFIG_GENERIC_PENDING_IRQ=y
x86/apic: Add separate apic_id_valid() functions for selected apic drivers
locking/kconfig: Simplify INLINE_SPIN_UNLOCK usage
x86/kconfig: Update defconfigs
x86: Fix excessive MSR print out when show_msr is not specified
Pull x86 platform driver updates from Matthew Garrett:
"Some significant updates to samsung-laptop, additional hardware
support for Toshibas, misc updates to various hardware and a new
backlight driver for some Apple machines."
Fix up trivial conflicts: geode Geos update happening next to net5501
support, and MSIC thermal platform support added twice.
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (77 commits)
acer-wmi: add quirk table for video backlight vendor mode
drivers/platform/x86/amilo-rfkill.c::amilo_rfkill_probe() avoid NULL deref
samsung-laptop: unregister ACPI video module for some well known laptops
acer-wmi: No wifi rfkill on Sony machines
thinkpad-acpi: recognize Lenovo as version string in newer V-series BIOS
asus-wmi: don't update power and brightness when using scalar
eeepc-wmi: split et2012 specific hacks
eeepc-wmi: refine quirks handling
asus-nb-wmi: set panel_power correctly
asus-wmi: move WAPF variable into quirks_entry
asus-wmi: store backlight power status for AIO machine
asus-wmi: add scalar board brightness adj. support
samsung-laptop: cleanup return type: mode_t vs umode_t
drivers, samsung-laptop: fix usage of isalnum
drivers, samsung-laptop: fix initialization of sabi_data in sabi_set_commandb
asus-wmi: on/off bit is not set when reading the value
eeepc-wmi: add extra keymaps for EP121
asus-nb-wmi: ignore useless keys
acer-wmi: support Lenovo ideapad S205 Brazos wifi switch
acer-wmi: fix out of input parameter size when set
...
Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BSW8
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO changes for v3.4 from Grant Likely:
"Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties."
Fix up context conflict due to Laxman Dewangan adding sleep control for
the tps65910 driver separately for gpio's and regulators.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio/ep93xx: Remove unused inline function and useless pr_err message
gpio/sodaville: Mark broken due to core irqdomain migration
gpio/omap: fix redundant decoding of gpio offset
gpio/omap: fix incorrect update to context.irqenable1
gpio/omap: fix incorrect context restore logic in omap_gpio_runtime_*
gpio/omap: fix missing dataout context save in _set_gpio_dataout_reg
gpio/omap: fix _set_gpio_irqenable implementation
gpio/omap: fix trigger type to unsigned
gpio/omap: fix wakeup_en register update in _set_gpio_wakeup()
gpio: tegra: tegra_gpio_config shouldn't be __init
gpio/davinci: fix enabling unbanked GPIO IRQs
gpio/davinci: fix oops on unbanked gpio irq request
gpio/omap: Fix section warning for omap_mpuio_alloc_gc()
ARM: tegra: export tegra_gpio_{en,dis}able
gpio/gpio-stmpe: Fix the value returned by _get_value routine
Documentation/gpio.txt: Explain expected pinctrl interaction
GPIO: LPC32xx: Add output reading to GPO P3
GPIO: LPC32xx: Fix missing bit selection mask
gpio/omap: fix wakeups on level-triggered GPIOs
gpio/omap: Fix IRQ handling for SPARSE_IRQ
...
Add a debugfs interface for sending commands to the OLPC
Embedded Controller (EC) and reading the responses. The EC
provides functionality for machine identification, battery and
AC control, wakeup control, etc.
Having a debugfs interface available is useful for EC
development and debugging.
Based on code by Paul Fox (who also approves of the end result).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Paul Fox <pgf@laptop.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andres Salomon <dilinger@queued.net>
Link: http://lkml.kernel.org/r/20120327150740.667D09D401E@zog.reactivated.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull drm main changes from Dave Airlie:
"This is the main drm pull request, I'm probably going to send two more
smaller ones, will explain below.
This contains a patch that is also in the fbdev tree, but it should be
the same patch, it added an API for hot unplugging framebuffer
devices, and I need that API for a new driver.
It also contains some changes to the i2c tree which Jean has acked,
and one change to moorestown platform stuff in x86.
Highlights:
- new drivers: UDL driver for USB displaylink devices, kms only,
should support correct hotplug operations.
- core: i2c speedups + better hotplug support, EDID overriding via
firmware interface - allows user to load a firmware for a broken
monitor/kvm from userspace, it even has documentation for it.
- exynos: new HDMI audio + hdmi 1.4 + virtual output driver
- gma500: code cleanup
- radeon: cleanups, CS optimisations, streamout support and pageflip
fix
- nouveau: NVD9 displayport support + more reclocking work
- i915: re-enabling GMBUS, finish gpu patch (might help hibernation
who knows), missed irq fixes, stencil tiling fixes, interlaced
support, aliasesd PPGTT support for SNB/IVB, swizzling for SNB/IVB,
semaphore fixes
As well as the usual bunch of cleanups and fixes all over the place.
I've got two things I'd like to merge a bit later:
a) AMD support for all their new radeonhd 7000 series GPU and APUs.
AMD dropped this a bit late due to insane internal review
processes, (please AMD just follow Intel and let open source guys
ship stuff early) however I don't want to penalise people who own
this hardware (since its been on sale for 3-4 months and GPU hw
doesn't exactly have a lifetime in years) and consign them to
using closed drivers for longer than necessary. The changes are
well contained and just plug into the driver new gpu functionality
so they should be fairly regression proof. I just want to give
them a bit of a run on the hw AMD kindly sent me.
b) drm prime/dma-buf interface code. This is just infrastructure
code to expose the dma-buf stuff to drm drivers and to userspace.
I'm not planning on pushing any driver support in this cycle
(except maybe exynos), but I'd like to get the infrastructure code
in so for the next cycle I can start getting the driver support
into the individual drivers. We have started driver support for
i915, nouveau and udl along with I think exynos and omap in
staging. However this code relies on the dma-buf tree being
pulled into your tree first since it needs the latest interfaces
from that tree. I'll push to get that tree sent asap.
(oh and any warnings you see in i915 are gcc's fault from what anyone
can see)."
Fix up trivial conflicts in arch/x86/platform/mrst/mrst.c due to the new
msic_thermal_platform_data() thermal function being added next to the
tc35876x_platform_data() i2c device function..
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (326 commits)
drm/i915: use DDC_ADDR instead of hard-coding it
drm/radeon: use DDC_ADDR instead of hard-coding it
drm: remove unneeded redefinition of DDC_ADDR
drm/exynos: added virtual display driver.
drm: allow loading an EDID as firmware to override broken monitor
drm/exynos: enable hdmi audio feature
drm/exynos: add default pixel format for plane
drm/exynos: cleanup exynos_hdmi.h
drm/exynos: add is_local member in exynos_drm_subdrv struct
drm/exynos: add subdrv open/close functions
drm/exynos: remove module of exynos drm subdrv
drm/exynos: release pending pageflip events when closed
drm/exynos: added new funtion to get/put dma address.
drm/exynos: update gem and buffer framework.
drm/exynos: added mode_fixup feature and code clean.
drm/exynos: add HDMI version 1.4 support
drm/exynos: remove exynos_mixer.h
gma500: Fix mmap frambuffer
drm/radeon: Drop radeon_gem_object_(un)pin.
drm/radeon: Restrict offset for legacy display engine.
...
Pull x86 platform changes from Ingo Molnar.
Removes the Moorestown platform that nobody ever used.
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform: Move APIC ID validity check into platform APIC code
x86/olpc/xo15/sci: Enable lid close wakeup control
x86/geode/net5501: Add platform driver for Soekris Engineering net5501
x86/geode/alix2: Supplement driver to include GPIO button support
x86/mid/powerbtn: Use MSIC read/write instead of ipc_scu
x86/mid/thermal: Turn off thermistor
x86/mid/thermal: Add msic_thermal alias
x86/mid/thermal: Convert to use Intel MSIC API
x86/mid/scu_ipc: Remove Moorestown support
x86/mid: Kill off Moorestown
x86/mrst: Add msic_thermal platform support
x86/config: Select MSIC MFD driver on Intel Medfield platform
x86/mid: Remove Intel Moorestown
x86/mrst: Set ISA bus type for fake MP IRQs
x86/ioapic: Use legacy_pic to set correct gsi-irq mapping
Pull trivial x86 branches from Ingo Molnar: small one-liners to fix up
details.
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove some noise from boot log when starting cpus
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Fix port argument to inl() function
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: Add CPU features from Intel document 319433-012A
* 'x86-process-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64: Record stack pointer before task execution begins
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/UV: Lower UV rtc clocksource rating
Trivial platform driver for Traverse Technologies Geos and Geos2
single-board computers. Uses SMBIOS to identify platform.
Based on progressive revisions of the leds-net5501 driver that
was rewritten by Ed Wildgoose as a platform driver.
Supports GPIO-based LEDs (3) and 1 polled button which is
typically used for a soft reset.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Reviewed-by: Ed Wildgoose <ed@wildgooses.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This will let the MSIC driver to create platform device for the thermal
driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
We need to merge this ahead of some of the cleanup because a lot of needed
cleanup spans both new and old chips. If we try and clean up and the merge
we end up fighting ourselves.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[With a load of the cleanup stuff folded in, register stuff reworked sanely]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Like most systems, OLPC's ACPI LID switch wakes up the system
when the lid is opened, but not when it is closed.
Under OLPC's opportunistic suspend model, the lid may be closed
while the system was oportunistically suspended with the screen
running. In this event, we want to wake up to turn the screen
off.
Enable control of normal ACPI wakeups through lid close events
through a new sysfs attribute "lid_wake_on_closed". When set,
and when LID wakeups are enabled through ACPI, the system will
wake up on both open and close lid events.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Matthew Garrett <mjg@redhat.com>
[ Fixed sscanf checking]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-bgt8hxu2wwe0x5p8edhogtf7@git.kernel.org
[ Did very minor readability tweaks ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add platform driver for the Soekris Engineering net5501 single-board
computer. Probes well-known locations in ROM for BIOS signature
to confirm correct platform. Registers 1 LED and 1 GPIO-based
button (typically used for soft reset).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Matthew Garrett <mjg@redhat.com>
[ Removed Kconfig and Makefile detritus from drivers/leds/]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-jv5uf34996juqh5syes8mn4h@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
GPIO 24 is used in reference designs as a soft-reset button, and
the alix2 is no exception. Add it as a gpio-button.
Use symbolic values to describe BIOS addresses.
Record the model number.
Signed-off-by: Philip A. Prindeville <philipp@redfish-solutions.com>
Acked-by: Ed Wildgoose <kernel@wildgooses.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-sjp6k1rjksitx1pej0c0qxd1@git.kernel.org
[ tidied up the code a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Traditionally the kernel has refused to setup EFI at all if there's been
a mismatch in 32/64-bit mode between EFI and the kernel.
On some platforms that boot natively through EFI (Chrome OS being one),
we still need to get at least some of the static data such as memory
configuration out of EFI. Runtime services aren't as critical, and
it's a significant amount of work to implement switching between the
operating modes to call between kernel and firmware for thise cases. So
I'm ignoring it for now.
v5:
* Fixed some printk strings based on feedback
* Renamed 32/64-bit specific types to not have _ prefix
* Fixed bug in printout of efi runtime disablement
v4:
* Some of the earlier cleanup was accidentally reverted by this patch, fixed.
* Reworded some messages to not have to line wrap printk strings
v3:
* Reorganized to a series of patches to make it easier to review, and
do some of the cleanups I had left out before.
v2:
* Added graceful error handling for 32-bit kernel that gets passed
EFI data above 4GB.
* Removed some warnings that were missed in first version.
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/1329081869-20779-6-git-send-email-olof@lixom.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
It's not perfect, but way better than before. Mark efi_enabled as false in
case of error and at least stop dereferencing pointers that are known to
be invalid.
The only significant missing piece is the lack of undoing the
memblock_reserve of the memory that efi marks as in use. On the other
hand, it's not a large amount of memory, and leaving it unavailable for
system use should be the safer choice anyway.
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/1329081869-20779-5-git-send-email-olof@lixom.net
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Trivial cleanup, move guid and table pointers to local copies to
make the code cleaner.
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/1329081869-20779-4-git-send-email-olof@lixom.net
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Alright, I guess I'll go through and convert them, even though
there's no net gain to speak of.
v4:
* Switched to pr_fmt and removed some redundant use of "EFI" in
messages.
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/1329081869-20779-3-git-send-email-olof@lixom.net
Cc: Joe Perches <joe@perches.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Break out some of the init steps into helper functions.
Only change to execution flow is the removal of the warning when the
kernel memdesc structure differ in size from what firmware specifies
since it's a bogus warning (it's a valid difference per spec).
v4:
* Removed memdesc warning as per above
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/1329081869-20779-2-git-send-email-olof@lixom.net
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Lower the rating of the UV rtc clocksource to just below that of
the tsc, to improve performance.
Reading the tsc clocksource has lower latency than reading the
rtc, so favor it in situations where it is synchronized and
stable. When the tsc is unsynchronized, the rtc needs to be the
chosen clocksource.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20120217141641.GA28063@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Sodaville has GPIO controller behind the PCI bus. To my suprissed it is
not the same as on PXA.
The interrupt & gpio chip can be referenced from the device tree like
from any other driver. Unfortunately the driver which uses the gpio
interrupt has to use irq_of_parse_and_map() instead of
platform_get_irq(). The problem is that the platform device (which is
created from the device tree) is most likely created before the
interrupt chip is registered and therefore irq_of_parse_and_map() fails.
In theory the driver works as module. In reality most of the irq
functions are not exported to modules and it is possible that _this_
module is unloaded while the provided irqs are still in use.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
[torbenh@linutronix.de: make it work after the irq namespace cleanup,
add some device tree entries.]
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
[bigeasy@linutronix.de: convert to generic irq & gpio chip]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[grant.likely@secretlab.ca: depend on x86 to avoid irq_domain breakage]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
update scx200_32.c to use pr_<level>, also 2 whitespaces.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This will let the MSIC driver to create platform device for the
thermal driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: jacob.jun.pan@linux.intel.com
Link: http://lkml.kernel.org/n/tip-rh1jaft9tjpzfql76gd56h1q@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All production devices operate in the Oaktrail configuration
with legacy PC elements present and an ACPI BIOS. Continue
stripping out the Moorestown elements from the tree leaving
Medfield.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: jacob.jun.pan@linux.intel.com
Link: http://lkml.kernel.org/n/tip-fvm1hgpq99jln6l0fbek68ik@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Initialize two spinlocks in tlb_uv.c and also properly define/initialize
the uv_irq_lock.
The lack of explicit initialization seems to be functionally
harmless, but it is diagnosed when these are turned on:
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_LOCKDEP=y
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/E1RnXd1-0003wU-PM@eag09.americas.sgi.com
[ Added the uv_irq_lock initialization fix by Dimitri Sivanich ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds separate accounting of UV2 message "strong
nack's" in the BAU statistics.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116212238.GF5767@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch moves the ack of the BAU interrupt to the beginning
of the interrupt handler so that there is less possibility of a
lost interrupt and slower response to a shootdown message.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116212146.GE5767@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch removes an unnecessary test for a
no-destination-resources-available condition that looks like a
destination timeout in UV1, but is separately distinguishable in
UV2.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116212050.GD5767@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch implements a workaround for a UV2 hardware bug.
The bug is a non-atomic update of a memory-mapped register. When
hardware message delivery and software message acknowledge occur
simultaneously the pending message acknowledge for the arriving
message may be lost. This causes the sender's message status to
stay busy.
Part of the workaround is to not acknowledge a completed message
until it is verified that no other message is actually using the
resource that is mistakenly recorded in the completed message.
Part of the workaround is to test for long elapsed time in such
a busy condition, then handle it by using a spare sending
descriptor. The stay-busy condition is eventually timed out by
hardware, and then the original sending descriptor can be
re-used. Most of that logic change is in keeping track of the
current descriptor and the state of the spares.
The occurrences of the workaround are added to the BAU
statistics.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116211947.GC5767@sgi.com
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the call to enable_timeouts() forward so that
BAU_MISC_CONTROL is initialized before using it in
calculate_destination_timeout().
Fix the calculation of a BAU destination timeout
for UV2 (in calculate_destination_timeout()).
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116211848.GB5767@sgi.com
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update the use of the Broadcast Assist Unit on SGI Altix UV2 to
the use of native UV2 mode on new hardware (not the legacy mode).
UV2 native mode has a different format for a broadcast message.
We also need quick differentiaton between UV1 and UV2.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116211750.GA5767@sgi.com
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel config: Fix the APB_TIMER selection
x86/mrst: Add additional debug prints for pb_keys
x86/intel config: Revamp configuration to allow for Moorestown and Medfield
x86/intel/scu/ipc: Match the changes in the x86 configuration
x86/apb: Fix configuration constraints
x86: Fix INTEL_MID silly
x86/Kconfig: Cyclone-timer depends on x86-summit
x86: Reduce clock calibration time during slave cpu startup
x86/config: Revamp configuration for MID devices
x86/sfi: Kill the IRQ as id hack
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: imx: move del_timer_sync() to avoid potential deadlock
imx: add polled io uart methods
imx: Add save/restore functions for UART control regs
serial/imx: let probing fail for the dt case without a valid alias
serial/imx: propagate error from of_alias_get_id instead of using -ENODEV
tty: serial: imx: Allow UART to be a source for wakeup
serial: driver for m32 arch should not have DEC alpha errata
serial/documentation: fix documented name of DCD cpp symbol
atmel_serial: fix spinlock lockup in RS485 code
tty: Fix memory leak in virtual console when enable unicode translation
serial: use DIV_ROUND_CLOSEST instead of open coding it
serial: add support for 400 and 800 v3 series Titan cards
serial: bfin-uart: Remove ASYNC_CTS_FLOW flag for hardware automatic CTS.
serial: bfin-uart: Enable hardware automatic CTS only when CTS pin is available.
serial: make FSL errata depend on 8250_CONSOLE, not just 8250
serial: add irq handler for Freescale 16550 errata.
serial: manually inline serial8250_handle_port
serial: make 8250 timeout use the specified IRQ handler
serial: export the key functions for an 8250 IRQ handler
serial: clean up parameter passing for 8250 Rx IRQ handling
...
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86: Fix atomic64_xxx_cx8() functions
x86: Fix and improve cmpxchg_double{,_local}()
x86_64, asm: Optimise fls(), ffs() and fls64()
x86, bitops: Move fls64.h inside __KERNEL__
x86: Fix and improve percpu_cmpxchg{8,16}b_double()
x86: Report cpb and eff_freq_ro flags correctly
x86/i386: Use less assembly in strlen(), speed things up a bit
x86: Use the same node_distance for 32 and 64-bit
x86: Fix rflags in FAKE_STACK_FRAME
x86: Clean up and extend do_int3()
x86: Call do_notify_resume() with interrupts enabled
x86/div64: Add a micro-optimization shortcut if base is power of two
x86-64: Cleanup some assembly entry points
x86-64: Slightly shorten line system call entry and exit paths
x86-64: Reduce amount of redundant code generated for invalidate_interruptNN
x86-64: Slightly shorten int_ret_from_sys_call
x86, efi: Convert efi_phys_get_time() args to physical addresses
x86: Default to vsyscall=emulate
x86-64: Set siginfo and context on vsyscall emulation faults
x86: consolidate xchg and xadd macros
...
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sysdev.h file should not be needed by any in-kernel code, so remove
the .h file from these random files that seem to still want to include
it.
The sysdev code will be going away soon, so this include needs to be
removed no matter what.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "Venkatesh Pallipadi
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Added additional debug output that we always seem to add
during power ons to validate firmware operation.
Signed-off-by: Michael Demeter <michael.demeter@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111215223116.10166.50803.stgit@bob.linux.org.uk
[ fixed line breaks, formatting and commit title. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This hangs my MacBook Air at boot time; I get no console
messages at all. I reverted this on top of -rc5 and my machine
boots again.
This reverts commit e8c7106280.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console
Signed-off-by: Ingo Molnar <mingo@elte.hu>
efi_call_phys_prelog() sets up a 1:1 mapping of the physical address
range in swapper_pg_dir. Instead of replacing then restoring entries
in swapper_pg_dir we should be using initial_page_table which already
contains the 1:1 mapping.
It's safe to blindly switch back to swapper_pg_dir in the epilog
because the physical EFI routines are only called before
efi_enter_virtual_mode(), e.g. before any user processes have been
forked. Therefore, we don't need to track which pgd was in %cr3 when
we entered the prelog.
The previous code actually contained a bug because it assumed that the
kernel was loaded at a physical address within the first 8MB of ram,
usually at 0x100000. However, this isn't the case with a
CONFIG_RELOCATABLE=y kernel which could have been loaded anywhere in
the physical address space.
Also delete the ancient (and bogus) comments about the page table
being restored after the lock is released. There is no locking.
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Darrent Hart <dvhart@linux.intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1323346250.3894.74.camel@mfleming-mobl1.ger.corp.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If we encounter an efi_memory_desc_t without EFI_MEMORY_WB set
in ->attribute we currently call set_memory_uc(), which in turn
calls __pa() on a potentially ioremap'd address.
On CONFIG_X86_32 this is invalid, resulting in the following
oops on some machines:
BUG: unable to handle kernel paging request at f7f22280
IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210
[...]
Call Trace:
[<c104f8ca>] ? page_is_ram+0x1a/0x40
[<c1025aff>] reserve_memtype+0xdf/0x2f0
[<c1024dc9>] set_memory_uc+0x49/0xa0
[<c19334d0>] efi_enter_virtual_mode+0x1c2/0x3aa
[<c19216d4>] start_kernel+0x291/0x2f2
[<c19211c7>] ? loglevel+0x1b/0x1b
[<c19210bf>] i386_start_kernel+0xbf/0xc8
A better approach to this problem is to map the memory region
with the correct attributes from the start, instead of modifying
it after the fact. The uncached case can be handled by
ioremap_nocache() and the cached by ioremap_cache().
Despite first impressions, it's not possible to use
ioremap_cache() to map all cached memory regions on
CONFIG_X86_64 because EFI_RUNTIME_SERVICES_DATA regions really
don't like being mapped into the vmalloc space, as detailed in
the following bug report,
https://bugzilla.redhat.com/show_bug.cgi?id=748516
Therefore, we need to ensure that any EFI_RUNTIME_SERVICES_DATA
regions are covered by the direct kernel mapping table on
CONFIG_X86_64. To accomplish this we now map E820_RESERVED_EFI
regions via the direct kernel mapping with the initial call to
init_memory_mapping() in setup_arch(), whereas previously these
regions wouldn't be mapped if they were after the last E820_RAM
region until efi_ioremap() was called. Doing it this way allows
us to delete efi_ioremap() completely.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console-pimps.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This follows on from the patch applied in 3.2rc1 which creates
an INTEL_MID configuration. We can now add the entry for
Medfield specific code. After this is merged the final patch
will be submitted which moves the rest of the device Kconfig
dependancies to MRST/MEDFIELD/INTEL_MID as appropriate.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Because callers of efi_phys_get_time() pass virtual stack
addresses as arguments, we need to find their corresponding
physical addresses and when calling GetTime() in physical mode.
Without this patch the following line is printed on boot,
"Oops: efitime: can't read time!"
Signed-off-by: Maurice Ma <maurice.ma@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1318330333-4617-1-git-send-email-matt@console-pimps.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In latest firmware's SFI tables, pmic_gpio has been set to
IPC type of device, so we need handle it too.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add SFI glue for the following devices:
tca6416: a gpio expander compatible with max7315
mpu3050: gyro sensor
Both of these actual drivers are already upstream
Signed-off-by: Jekyll Lai <jekyll_lai@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On the Intel MID devices SCU commands are issued to manage power
off and the like. We need to issue different ones for
non-Lincroft based devices.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts & resolutions:
* arch/x86/xen/setup.c
dc91c728fd "xen: allow extra memory to be in multiple regions"
24aa07882b "memblock, x86: Replace memblock_x86_reserve/free..."
conflicted on xen_add_extra_mem() updates. The resolution is
trivial as the latter just want to replace
memblock_x86_reserve_range() with memblock_reserve().
* drivers/pci/intel-iommu.c
166e9278a3 "x86/ia64: intel-iommu: move to drivers/iommu/"
5dfe8660a3 "bootmem: Replace work_with_active_regions() with..."
conflicted as the former moved the file under drivers/iommu/.
Resolved by applying the chnages from the latter on the moved
file.
* mm/Kconfig
6661672053 "memblock: add NO_BOOTMEM config symbol"
c378ddd53f "memblock, x86: Make ARCH_DISCARD_MEMBLOCK a config option"
conflicted trivially. Both added config options. Just
letting both add their own options resolves the conflict.
* mm/memblock.c
d1f0ece6cd "mm/memblock.c: small function definition fixes"
ed7b56a799 "memblock: Remove memblock_memory_can_coalesce()"
confliected. The former updates function removed by the
latter. Resolution is trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
random: Fix handing of arch_get_random_long in get_random_bytes()
x86: Call stop_machine_text_poke() on all CPUs
x86, ioapic: Only print ioapic debug information for IRQs belonging to an ioapic chip
x86/mrst: Avoid reporting wrong nmi status
x86/mrst: Add support for Penwell clock calibration
x86/apic: Allow use of lapic timer early calibration result
x86/apic: Do not clear nr_irqs_gsi if no legacy irqs
x86/platform: Add a wallclock_init func to x86_platforms ops
x86/mce: Make mce_chrdev_ops 'static const'
Add support to specify which HSU port to use as an early console. This can
be selected by passing "earlyprintk=hsu<n>" on the kernel command line. By
default port 0 is still used.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This needed the sfi IRQ 0xFF fix to go in first. It simply plumbs in the
bma023 driver with the firmware naming of it.
Signed-off-by: William Douglas <william.douglas@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Real world year equals the value in vrtc YEAR register plus an offset.
We used 1960 as the offset to make leap year consistent, but for a
device's first use, its YEAR register is 0 and the system year will
be parsed as 1960 which is not a valid UNIX time and will cause many
applications to fail mysteriously. So we use 1972 instead to fix this
issue.
Updated patch which adds a sanity check suggested by Mathias
This isn't a change in behaviour for systems, because 1972 is the one we
actually use. It's the old version in upstream which is out of sync with
all devices.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a build error. CE4100 with no serial errors because the alternate
function is only a prototype not a null function as intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Moorestown/Medfield platform does not have port 0x61 to report
NMI status, nor does it have external NMI sources. The only NMI
sources are from lapic, as results of perf counter overflow or
IPI, e.g. NMI watchdog or spin lock debug.
Reading port 0x61 on Moorestown will return 0xff which misled
NMI handlers to false critical errors such memory parity error.
The subsequent ioport access for NMI handling can also cause
undefined behavior on Moorestown.
This patch allows kernel process NMI due to watchdog or backrace
dump without unnecessary hangs.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[hand applied]
Signed-off-by: Alan Cox <alan@linux.intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
cpuidle: Single/Global registration of idle states
cpuidle: Split cpuidle_state structure and move per-cpu statistics fields
cpuidle: Remove CPUIDLE_FLAG_IGNORE and dev->prepare()
cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
ACPI: Fix CONFIG_ACPI_DOCK=n compiler warning
ACPI: Export FADT pm_profile integer value to userspace
thermal: Prevent polling from happening during system suspend
ACPI: Drop ACPI_NO_HARDWARE_INIT
ACPI atomicio: Convert width in bits to bytes in __acpi_ioremap_fast()
PNPACPI: Simplify disabled resource registration
ACPI: Fix possible recursive locking in hwregs.c
ACPI: use kstrdup()
mrst pmu: update comment
tools/power turbostat: less verbose debugging
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
We want to clean up the chain of includes stumbling through
module.h, and when we do that, we'll see:
CC arch/x86/platform/efi/efi_32.o
efi/efi_32.c: In function ‘efi_call_phys_prelog’:
efi/efi_32.c:80: error: implicit declaration of function ‘get_cpu_gdt_table’
efi/efi_32.c:82: error: implicit declaration of function ‘load_gdt’
make[4]: *** [arch/x86/platform/efi/efi_32.o] Error 1
Include asm/desc.h so that there are no implicit include assumptions.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were implicitly getting EXPORT_SYMBOL via device.h
which was including module.h, but that will be fixed up shortly.
By fixing these now, we can avoid seeing things like:
arch/x86/kernel/rtc.c:29: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/x86/kernel/pci-dma.c:20: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/x86/kernel/e820.c:69: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’
[ with input from Randy Dunlap <rdunlap@xenotime.net> and also
from Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
TTY: serial_core: Fix crash if DCD drop during suspend
tty/serial: atmel_serial: bootconsole removed from auto-enumerates
Revert "TTY: call tty_driver_lookup_tty unconditionally"
tty/serial: atmel_serial: add device tree support
tty/serial: atmel_serial: auto-enumerate ports
tty/serial: atmel_serial: whitespace and braces modifications
tty/serial: atmel_serial: change platform_data variable name
tty/serial: RS485 bindings for device tree
TTY: call tty_driver_lookup_tty unconditionally
TTY: pty, release tty in all ptmx_open fail paths
TTY: make tty_add_file non-failing
TTY: drop driver reference in tty_open fail path
8250_pci: Fix kernel panic when pch_uart is disabled
h8300: drivers/serial/Kconfig was moved
parport_pc: release IO region properly if unsupported ITE887x card is found
tty: Support compat_ioctl get/set termios_locked
hvc_console: display printk messages on console.
TTY: snyclinkmp: forever loop in tx_load_dma_buffer()
tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output
tty/n_gsm: fix a bug in gsm_dlci_data_output (adaption = 2 case)
...
Fix up Conflicts in:
- drivers/tty/serial/8250_pci.c
Trivial conflict with removed duplicate device ID
- drivers/tty/serial/atmel_serial.c
Annoying silly conflict between "specify the port num via
platform_data" and other changes to atmel_console_init
The MSIC MFD driver creates platform devices for MSIC device drivers so we
don't need to create them in platform code anymore.
This patch adds a new runtime check which determines whether we are running
on a Medfield platform and enables the MSIC MFD driver accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a notifier so that drivers can hook into SCU availability in order to
take actions post initialisation when/if the SCU becomes available.
In the ideal world we wouldn't need this and we could avoid any init
dependancies of this form, but in practice we can't do it for some cases.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
SFI tables reside in RAM and should not be modified once they are
written. Current code went to set pentry->irq to zero which causes
subsequent reads to fail with invalid SFI table checksum. This will
break kexec as the second kernel fails to validate SFI tables.
To fix this we use temporary variable for irq number.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A deadlock was introduced on x86 in commit ef68c8f87e ("x86:
Serialize EFI time accesses on rtc_lock") because efi_get_time()
and friends can be called with rtc_lock already held by
read_persistent_time(), e.g.:
timekeeping_init()
read_persistent_clock() <-- acquire rtc_lock
efi_get_time()
phys_efi_get_time() <-- acquire rtc_lock <DEADLOCK>
To fix this let's push the locking down into the get_wallclock()
and set_wallclock() implementations. Only the clock
implementations that access the x86 RTC directly need to acquire
rtc_lock, so it makes sense to push the locking down into the
rtc, vrtc and efi code.
The virtualization implementations don't require rtc_lock to be
held because they provide their own serialization.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Avi Kivity <avi@redhat.com> [for the virtualization aspect]
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is a workaround for a UV2 hub bug that affects the format of system
global addresses.
The GRU API for UV2 was inadvertently broken by a hardware change. The
format of the physical address used for TLB dropins and for addresses used
with instructions running in unmapped mode has changed. This change was
not documented and became apparent only when diags failed running on
system simulators.
For UV1, TLB and GRU instruction physical addresses are identical to
socket physical addresses (although high NASID bits must be OR'ed into the
address).
For UV2, socket physical addresses need to be converted. The NODE portion
of the physical address needs to be shifted so that the low bit is in bit
39 or bit 40, depending on an MMR value.
It is not yet clear if this bug will be fixed in a silicon respin. If it
is fixed, the hub revision will be incremented & the workaround disabled.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This new driver replaces the old PCEngines Alix 2/3 LED driver with a
new driver that controls the LEDs through the leds-gpio driver. The
old driver accessed GPIOs directly, which created a conflict and
prevented also loading the cs5535-gpio driver to read other GPIOs on
the Alix board. With this new driver, we hook into leds-gpio which in
turn uses GPIO to control the LEDs and therefore it's possible to
control both the LEDs and access onboard GPIOs
Driver is moved to platform/geode as requested by Grant and any other
geode initialisation modules should move here also
This driver is inspired by leds-net5501.c by Alessandro Zummo.
Ideally, leds-net5501.c should also be moved to platform/geode.
Additionally the driver relies on parts of the patch: 7f131cf3ed ("leds:
leds-alix2c - take port address from MSR) by Daniel Mack to perform
detection of the Alix board.
[akpm@linux-foundation.org: include module.h]
Signed-off-by: Ed Wildgoose <kernel@wildgooses.com>
Cc: git@wildgooses.com
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Those info will be used when spi controller driver setup
max3110 as a slave device
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the SFI specification irq number 0xFF means device has no
interrupt or interrupt attached via GPIO.
Currently, we don't handle this special case and set irq field in
*_board_info structs to 255. It leads to confusion in some drivers.
Accelerometer driver tries to register interrupt 255, fails and prints
"Cannot get IRQ" to dmesg.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When executing EC commands, only waiting when there are still
more bytes to write is usually fine. However, if the system
suspends very quickly after a call to olpc_ec_cmd(), the last
data byte may not yet be transferred to the EC, and the command
will not complete.
This solves a bug where the SCI wakeup mask was not correctly
written when going into suspend.
It means that sometimes, on XO-1.5 (but not XO-1), the
devices that were marked as wakeup sources can't wake up
the system. e.g. you ask for wifi wakeups, suspend, but then
incoming wifi frames don't wake up the system as they should.
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
cpuidle: stop depending on pm_idle
x86 idle: move mwait_idle_with_hints() to where it is used
cpuidle: replace xen access to x86 pm_idle and default_idle
cpuidle: create bootparam "cpuidle.off=1"
mrst_pmu: driver for Intel Moorestown Power Management Unit
The Moorestown (MRST) Power Management Unit (PMU) driver
directs the SOC power states in the "Langwell" south complex (SCU).
It hooks pci_platform_pm_ops[] and thus observes all PCI ".set_state"
requests. For devices in the SC, the pmu driver translates those
PCI requests into the appropriate commands for the SCU.
The PMU driver helps implement S0i3, a deep system idle power idle state.
Entry into S0i3 is via cpuidle, just like regular processor c-states.
S0i3 depends on pre-conditions including uni-processor, graphics off,
and certain IO devices in the SC must be off. If those pre-conditions
are met, then the PMU allows cpuidle to enter S0i3, otherwise such requests
are demoted, either to Atom C4 or Atom C6.
This driver is based on prototype work by Bruce Flemming,
Illyas Mansoor, Rajeev D. Muralidhar, Vishwesh M. Rudramuni,
Hari Seshadri and Sujith Thomas. The current driver also
includes contributions from H. Peter Anvin, Arjan van de Ven,
Kristen Accardi, and Yong Wang.
Thanks for additional review feedback from Alan Cox and Randy Dunlap.
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some recent changes to the way that ACPI handles wakeup flags
means that the XO15EC ACPI device is not wakeup-capable by
default so device_set_wakeup_enable() does nothing.
Use device_init_wakeup() to mark the device as wakeup capable,
and to enable wakeups.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/20110724173430.BE03C9D401C@zog.reactivated.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Serialize EFI time accesses on rtc_lock
x86: Serialize SMP bootup CMOS accesses on rtc_lock
rtc: stmp3xxx: Remove UIE handlers
rtc: stmp3xxx: Get rid of mach-specific accessors
rtc: stmp3xxx: Initialize drvdata before registering device
rtc: stmp3xxx: Port stmp-functions to mxs-equivalents
rtc: stmp3xxx: Restore register definitions
rtc: vt8500: Use define instead of hardcoded value for status bit
The EFI specification requires that callers of the time related
runtime functions serialize with other CMOS accesses in the
kernel, as the EFI time functions may choose to also use the
legacy CMOS RTC.
Besides fixing a latent bug, this is a prerequisite to safely
enable the rtc-efi driver for x86, which ought to be preferred
over rtc-cmos on all EFI platforms.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: <mjg@redhat.com>
Link: http://lkml.kernel.org/r/4E257E33020000780004E319@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Matthew Garrett <mjg@redhat.com>
Other than sanity check and debug message, the x86 specific version of
memblock reserve/free functions are simple wrappers around the generic
versions - memblock_reserve/free().
This patch adds debug messages with caller identification to the
generic versions and replaces x86 specific ones and kills them.
arch/x86/include/asm/memblock.h and arch/x86/mm/memblock.c are empty
after this change and removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1310462166-31469-14-git-send-email-tj@kernel.org
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The return value of memblock_x86_check_reserved_size() doesn't
indicate whether there's an overlapping reservatoin or not. It
indicates whether the caller needs to iterate further to discover all
reserved portions of the specified area.
efi_reserve_boot_esrvices() wants to check whether the boot services
area overlaps with other reservations but incorrectly used
membloc_x86_check_reserved_size(). Use memblock_is_region_reserved()
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1310457490-3356-2-git-send-email-tj@kernel.org
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Testing suggests that at least some Lenovos and some Intels will
fail to reboot via EFI, attempting to jump to an unmapped
physical address. In the long run we could handle this by
providing a page table with a 1:1 mapping of physical addresses,
but for now it's probably just easier to assume that ACPI or
legacy methods will be present and reboot via those.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/1309985557-15350-1-git-send-email-mjg@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a driver for the ACPI-based EC event interface found on the
OLPC XO-1.5 laptop. This enables notification of battery/AC power events,
and enables various devices to be used as wakeup sources through regular
ACPI mechanisms.
This driver can't be built as a module, because some drivers need to know
at boot-time if SCI-based functionality is available via
olpc_ec_wakeup_available().
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-12-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add a driver to configure the XO-1 RTC via CS5536 MSRs, to be used as a
system wakeup source via olpc-xo1-pm.
Device detection is based on finding the relevant device tree node.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-11-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
EC events indicate change in AC power connectivity, battery state of
charge, battery error, battery presence, etc. Send notifications to
the power supply subsystem when changes are detected.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-10-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Configure the XO-1's lid switch GPIO to trigger an SCI interrupt,
and correctly expose this input device which can be used as a wakeup
source.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-9-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The EC in the OLPC XO-1 delivers GPE events to provide various
notifications. Add the basic code for GPE/EC event processing and
enable the ebook switch, which can be used as a wakeup source.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-8-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Update the EC SCI masks with recent additions.
Add functions to query SCI events and set the wakeup mask, to be used by
followup patches.
Add functions to tweak an event mask used to select certain EC events as
a system wakeup source. Also add a function to determine if EC wakeup
functionality is available, as this depends on child drivers (different
for each laptop model) to configure the SCI interrupt.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-7-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The System Control Interrupt is used in the OLPC XO-1 to control various
features of the laptop. Add the driver base and the power button
functionality.
This driver can't be built as a module, because functionality added in
future patches means that some drivers need to know at boot-time whether
SCI-based functionality is available.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-6-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add code needed for basic suspend/resume of the XO-1 laptop.
Based on earlier work by Jordan Crouse, Andres Salomon, and others.
This patch incorporates all earlier feedback from Thomas Gleixner. To
clarify a certain point (now more obvious in the code itself):
On resume, OpenFirmware returns execution to Linux in protected mode
with a kernel-compatible GDT already set up. The changes and
simplifications suggested have all been included.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-5-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Based on earlier review comments, we'll no longer try to stick all of
our XO-1 goodies in a single driver. We'll split it into a power management
driver, and an EC/SCI driver.
As a first step, rename olpc-xo1 to olpc-xo1-pm, and make it builtin
instead of modular.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-4-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Move these definitions into the relevant header file.
This was requested in the review of the upcoming XO-1 suspend/resume code.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-3-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In response to new device tree code in the kernel, OLPC will start
using it for probing of certain devices. However, some firmware fixes
are needed to put the devicetree into a usable state.
Retain compatibility with old firmware by fixing up the device tree
at boot-time if it does not contain the new nodes/properties that
we need for probing. This is the same approach taken on PPC platforms.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-2-git-send-email-dsd@laptop.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Consumers of the table pointers in struct efi check for
EFI_INVALID_TABLE_ADDR to determine validity, hence these
pointers should all be pre-initialized to this value (rather
than zero).
Noticed by the discrepancy between efivars' systab sysfs entry
showing all tables (and their pointers) despite the code
intending to only display the valid ones. No other bad effects
known, but having the various table parsing routines bogusly
access physical address zero is certainly not very desirable
(even though they're unlikely to find anything useful there).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Link: http://lkml.kernel.org/r/4E13100A020000780004C256@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a memory leak in init_per_cpu() when the topology check
fails.
The leak should never occur on deployed systems. It would only occur
in an unexpected topology that would make the BAU unuseable as a result.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122242.981533045@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the large stack-resident cpumask_t from
reset_with_ipi()'s stack by allocating one per uvhub.
Due to the limited size of the stack the potentially huge cpumask_t may
cause stack overrun. We haven't seen it happen yet, but we need to make it
a practice not to push such structures onto the stack.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/20110621122242.832589130@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename 'bau_targ_hubmask' to 'pnmask' for clarity.
The BAU distribution bit mask is indexed by pnode number, not hub or
blade number. This important fact is not clear while the mask is
called a 'hubmask'.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122242.630995969@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix reset_with_ipi() to look up a cpu for a blade based on the
distribution map being indexed by the potentially sparsely
numbered pnode.
This patch is critical to tlb shootdown on a partitioned UV
system, or one with nonconsecutive blade numbers.
The distribution map bits represent pnodes relative to the partition base
pnode. Previous to this patch it had been assuming bits based on 0-based,
consecutive blade ids.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122242.497700003@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix for the topology in which there is a socket 1 on a blade
with no socket 0.
Only call make_per_cpu_thp() for present sockets.
We have only seen this fail for internal configurations.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122242.363757364@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a call by tunables_write() to smp_processor_id() within a
preemptable region.
Call get_cpu()/put_cpu() around the region where the returned
cpu number is actually used, which makes it non-preemptable.
A DEBUG_PREEMPT warning is prevented.
UV does not support cpu hotplug yet, but this is a step toward
that ability as well.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122242.086384966@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 916f676f8d started reserving boot service code since some systems
require you to keep that code around until SetVirtualAddressMap is called.
However, in some cases those areas will overlap with reserved regions.
The proper medium-term fix is to fix the bootloader to prevent the
conflicts from occurring by moving the kernel to a better position,
but the kernel should check for this possibility, and only reserve regions
which can be reserved.
Signed-off-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Link: http://lkml.kernel.org/r/4DF7A005.1050407@gmail.com
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We're currently missing support for any of the runtime service calls
introduced with the UEFI 2.0 spec in 2006. Add the infrastructure for
supporting them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1307388985-7852-2-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
UEFI stands for "Unified Extensible Firmware Interface", where "Firmware"
is an ancient African word meaning "Why do something right when you can
do it so wrong that children will weep and brave adults will cower before
you", and "UEI" is Celtic for "We missed DOS so we burned it into your
ROMs". The UEFI specification provides for runtime services (ie, another
way for the operating system to be forced to depend on the firmware) and
we rely on these for certain trivial tasks such as setting up the
bootloader. But some hardware fails to work if we attempt to use these
runtime services from physical mode, and so we have to switch into virtual
mode. So far so dreadful.
The specification makes it clear that the operating system is free to do
whatever it wants with boot services code after ExitBootServices() has been
called. SetVirtualAddressMap() can't be called until ExitBootServices() has
been. So, obviously, a whole bunch of EFI implementations call into boot
services code when we do that. Since we've been charmingly naive and
trusted that the specification may be somehow relevant to the real world,
we've already stuffed a picture of a penguin or something in that address
space. And just to make things more entertaining, we've also marked it
non-executable.
This patch allocates the boot services regions during EFI init and makes
sure that they're executable. Then, after SetVirtualAddressMap(), it
discards them and everyone lives happily ever after. Except for the ones
who have to work on EFI, who live sad lives haunted by the knowledge that
someone's eventually going to write yet another firmware specification.
[ hpa: adding this to urgent with a stable tag since it fixes currently-broken
hardware. However, I do not know what the dependencies are and so I do
not know which -stable versions this may be a candidate for. ]
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1306331593-28715-1-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <stable@kernel.org>
SGI UV's uv_tlb.c driver has become rather hard to read, with overly large
functions, non-standard coding style and (way) too long variable, constant
and function names and non-obvious code flow sequences.
This patch improves the readability and maintainability of the driver
significantly, by doing the following strict code cleanups with no side
effects:
- Split long functions into shorter logical functions.
- Shortened some variable and structure member names.
- Added special functions for reads and writes of MMR regs with
very long names.
- Added the 'tunables' table to shortened tunables_write().
- Added the 'stat_description' table to shorten uv_ptc_proc_write().
- Pass fewer 'stat' arguments where it can be derived from the 'bcp'
argument.
- Function definitions consistent on one line, and inline in few (short) cases.
- Moved some small structures and an atomic inline function to the header file.
- Moved some local variables to the blocks where they are used.
- Updated the copyright date.
- Shortened uv_write_global_mmr64() etc. using some aliasing; no
line breaks. Renamed many uv_.. functions that are not exported.
- Aligned structure fields.
[ note that not all structures are aligned the same way though; I'd like
to keep the extensive commenting in some of them. ]
- Shortened some long structure names.
- Standard pass/fail exit from init_per_cpu()
- Vertical alignment for mass initializations.
- More separation between blocks of code.
Tested on a 16-processor Altix UV.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: penberg@kernel.org
Link: http://lkml.kernel.org/r/E1QOw12-0004MN-Lp@eag09.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds support for a new version of the SGI UV hub
chip. The hub chip is the node controller that connects multiple
blades into a larger coherent SSI.
For the most part, UV2 is compatible with UV1. The majority of
the changes are in the addresses of MMRs and in a few cases, the
contents of MMRs. These changes are the result in changes in the
system topology such as node configuration, processor types,
maximum nodes, physical address sizes, etc.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20110511175028.GA18006@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Introduce pci_map_biosrom()
x86, olpc: Use device tree for platform identification
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, efi: Ensure that the entirity of a region is mapped
x86, efi: Pass a minimal map to SetVirtualAddressMap()
x86, efi: Merge contiguous memory regions of the same type and attribute
x86, efi: Consolidate EFI nx control
x86, efi: Remove virtual-mode SetVirtualAddressMap call
* 'x86-gart-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, gart: Don't enforce GART aperture lower-bound by alignment
* 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Don't unmask disabled irqs when migrating them
x86: Skip migrating IRQF_PER_CPU irqs in fixup_irqs()
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mce: Drop the default decoding notifier
x86, MCE: Do not taint when handling correctable errors
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: convert mips to generic i8253 clocksource
clocksource: convert x86 to generic i8253 clocksource
clocksource: convert footbridge to generic i8253 clocksource
clocksource: add common i8253 PIT clocksource
blackfin: convert to clocksource_register_hz
mips: convert to clocksource_register_hz/khz
sparc: convert to clocksource_register_hz/khz
alpha: convert to clocksource_register_hz
microblaze: convert to clocksource_register_hz/khz
ia64: convert to clocksource_register_hz/khz
x86: Convert remaining x86 clocksources to clocksource_register_hz/khz
Make clocksource name const
Conflicts:
arch/ia64/kernel/cyclone.c
arch/mips/kernel/i8253.c
arch/x86/kernel/i8253.c
Reason: Resolve conflicts so further cleanups do not conflict further
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is a fix for the SGI Altix-UV Broadcast Assist Unit code,
which is used for TLB flushing.
Certain hardware configurations (that customers are ordering)
cause nasids (numa address space id's) to be non-consecutive.
Specifically, once you have more than 4 blades in a IRU
(Individual Rack Unit - or 1/2 rack) but less than the maximum
of 16, the nasid numbering becomes non-consecutive. This
currently results in a 'catastrophic error' (CATERR) detected by
the firmware during OS boot. The BAU is generating an 'INTD'
request that is targeting a non-existent nasid value. Such
configurations may also occur when a blade is configured off
because of hardware errors. (There is one UV hub per blade.)
This patch is required to support such configurations.
The problem with the tlb_uv.c code is that is using the
consecutive hub numbers as indices to the BAU distribution bit
map. These are simply the ordinal position of the hub or blade
within its partition. It should be using physical node numbers
(pnodes), which correspond to the physical nasid values. Use of
the hub number only works as long as the nasids in the partition
are consecutive and increase with a stride of 1.
This patch changes the index to be the pnode number, thus
allowing nasids to be non-consecutive.
It also provides a table in local memory for each cpu to
translate target cpu number to target pnode and nasid.
And it improves naming to properly reflect 'node' and 'uvhub'
versus 'nasid'.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/E1QJmxX-0002Mz-Fk@eag09.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's possible for init_memory_mapping() to fail to map the entire region
if it crosses a boundary, so ensure that we complete the mapping.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-5-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Experimentation with various EFI implementations has shown that functions
outside runtime services will still update their pointers if
SetVirtualAddressMap() is called with memory descriptors outside the
runtime area. This is obviously insane, and therefore is unsurprising.
Evidence from instrumenting another EFI implementation suggests that it
only passes the set of descriptors covering runtime regions, so let's
avoid any problems by doing the same. Runtime descriptors are copied to
a separate memory map, and only that map is passed back to the firmware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-4-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Some firmware implementations assume that physically contiguous regions
will be contiguous in virtual address space. This assumption is, obviously,
entirely unjustifiable. Said firmware implementations lack the good grace
to handle their failings in a measured and reasonable manner, instead
tending to shit all over address space and oopsing the kernel.
In an ideal universe these firmware implementations would simultaneously
catch fire and cease to be a problem, but since some of them are present
in attractively thin and shiny metal devices vanity wins out and some
poor developer spends an extended period of time surrounded by a
growing array of empty bottles until the underlying reason becomes
apparent. Said developer presents this patch, which simply merges
adjacent regions if they happen to be contiguous and have the same EFI
memory type and caching attributes.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-3-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The core EFI code and 64-bit EFI code currently have independent
implementations of code for setting memory regions as executable or not.
Let's consolidate them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-2-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The spec says that SetVirtualAddressMap doesn't work once you're in
virtual mode, so there's no point in having infrastructure for calling
it from there.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1304623186-18261-1-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fix these Sparse complaints:
CHECK arch/x86/platform/mrst/mrst.c
arch/x86/platform/mrst/mrst.c:197:13: warning: symbol 'mrst_time_init' was not declared. Should it be static?
arch/x86/platform/mrst/mrst.c:219:16: warning: symbol 'mrst_arch_setup' was not declared. Should it be static?
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Roman Gezikov <roman.gezikov@atheros.com>
Cc: Joonas Viskari <joonas.viskari@atheros.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Allen Kao <allen.kao@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Link: http://lkml.kernel.org/r/1304719209-26913-1-git-send-email-lrodriguez@atheros.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The USB and SATA ioapic interrrupt pins are configured as edge type,
but need to be level type interrupts to work correctly.
[ tglx: Split out from the combo patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Moorestown systems crash on boot because the secondary CPU
clockevent (apbt1) will fail to request irq#1, which does not
have ioapic chip in its irq_desc[] entry.
Background:
Moorestown platform does not have ISA bus nor legacy IRQs. It
reuses the range of legacy IRQs for regular device interrupts.
The routing information of early system device IRQs (timers) are
obtained from firmware provided SFI tables. We reuse/fake MP
configuration table to facilitate IRQ setup with IOAPIC.
Maintaining a 1:1 mapping of IOAPIC pin (RTE entry) and IRQ#
makes routing information clean and easy to understand on
Moorestown. Though optional.
This patch allows SFI timer and vRTC IRQ to be treated as ISA
IRQ so that pin2irq mapping will be 1:1.
Also fixed MP table type and use macros to clearly set MP IRQ
entries. As a result, apbt timer and RTC interrupts on
Moorestown are within legacy IRQ range:
# cat /proc/interrupts
CPU0 CPU1
0: 11249 0 IO-APIC-edge apbt0
1: 0 12271 IO-APIC-edge apbt1
8: 887 0 IO-APIC-fasteoi dw_spi
13: 0 0 IO-APIC-fasteoi INTEL_MID_DMAC2
14: 0 0 IO-APIC-fasteoi rtc0
Further discussion of this patch can be found at:
https://lkml.org/lkml/2010/6/10/70
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Link: http://lkml.kernel.org/r/1302286980-21139-1-git-send-email-jacob.jun.pan@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
without the reg property Ben's new code won't find the PCI & ISA
bridge and the devices won't get the DT-node attached.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: monstr@monstr.eu
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/20110407121315.GA9204@linutronix.de
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix FPU exception handling on non-SSE systems
x86, hibernate: Initialize mmu_cr4_features during boot
x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
x86: visws: Fixup irq overhaul fallout
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Clean up rebalance_domains() load-balance interval calculation
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mrst/vrtc: Fix boot crash in mrst_rtc_init()
rtc, x86/mrst/vrtc: Fix boot crash in rtc_read_alarm()
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix cpumask leak in __setup_irq()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix listing incorrect line number with inline function
perf probe: Fix to find recursively inlined function
perf probe: Fix multiple --vars options behavior
perf probe: Fix to remove redundant close
perf probe: Fix to ensure function declared file
The sfi_mrtc_array[] only gets initialized when the sfi mrtc
table is parsed, so the vrtc_paddr should be initalized after it
too.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302140389-27603-1-git-send-email-feng.tang@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stop including <linux/delay.h> in x86 header files which don't
need it. This will let the compiler complain when this header is
not included by source files when it should, so that
contributors can fix the problem before building on other
architectures starts to fail.
Credits go to Geert for the idea.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20110325152014.297890ec@endymion.delvare>
[ this also fixes an upstream build bug in drivers/media/rc/ite-cir.c ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The cs5535-pms cell doesn't actually need to be cloned, so we can drop that
and simply have the olpc-xo1.c driver use "cs5535-pms" directly.
Also, rename the cs5535-acpi clones to what we actually use for the (currently
out-of-tree) SCI driver. In the process, that fixes a subtle bug in
olpc-xo1.c which broke powerdown on XO-1s.. olpc-xo1-ac-acpi was a typo, not
something that actually existed.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace mfd_shared_platform_driver_register with mfd_clone_cell. The
former was called by an mfd client, and registered both a platform driver
and device. The latter is called by an mfd driver, and registers only a
platform device.
The downside of this is that mfd drivers need to be modified whenever
new clients are added that share a cell; the upside is that it fits
Linux's driver model better. It's also simpler.
This also converts cs5535-mfd/olpc-xo1 from the old API. cs5535-mfd
now creates the olpc-xo1-{acpi,pms} devices, while olpc-xo1 binds to
them via platform drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cliff Wickman