The USB 2.0 specification says that bMaxPower is the maximum power
consumption expressed in 2 mA units and the USB 3.0 specification says
that it is expressed in 8 mA units.
This patch adds a helper function usb_get_max_power() which computes the
value based on config & usb_device's speed value. The the device descriptor
dump computes the value on its own.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
although we can not say it is surely a bug.
it is better to set urb->hcpriv = NULL, after finish calling
urb_free_priv.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Basically remove unneeded code. Since that 'continue' is at the end
of the for() there's no need for it.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new function to unlink and abort requests from the work
list, call it on bus reset and disconnect where we kill all
in-flight urbs. Also reorder calls in disconnect to first
cancel transfers, then remove the scsi hba.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two changes. First we check whenever the request is linked in the work
list and if so take it out. Second check whenever the command is
actually in flight before asking the device to cancel it via task
management, and in case it isn't just zap the data urbs and finish it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep track whenever the request is linked into the work list or not.
Needed for request abort.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uas_unlink_data_urbs uses this to make sure the the scsi command is
not released while looking at it. This will be needed when we start
calling uas_unlink_data_urbs in the request cancel code paths.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add uas_unlink_data_urbs function to cancel in-flight data urbs.
Moves existing code into a separate function.
[ v2: also drop the locking, just call usb_unlink_urb no matter what,
which is safe because the usb core guarantees the completion
callback is called only once ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds new driver of SMSC USB3503 USB 2.0 hub controller with HSIC
upstream connectivity and three USB 2.0 downstream ports. The specification
can be found from 'http://www.smsc.com/index.php?tid=295&pid=325'.
The current version have been tested very basic features switching the modes,
HUB-MODE and STANDBY-MODE.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's some patches for 3.9. They further improve the warm reset
error handling, but they're too big to go into stable. There's also a
patch to remove an unused variable in the xHCI driver.
As I mentioned, you'll need to merge usb-linus into usb-next before
applying these patches.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=VBlC
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
usb-next: Further warm reset improvements
Hi Greg,
Here's some patches for 3.9. They further improve the warm reset
error handling, but they're too big to go into stable. There's also a
patch to remove an unused variable in the xHCI driver.
As I mentioned, you'll need to merge usb-linus into usb-next before
applying these patches.
Sarah Sharp
Hi Greg,
Happy New Year! Here's some bug fixes for 3.8. I have usb-next
patches that are based on this set, so please merge your usb-linus
branch into usb-next after this set is applied.
The bulk of the patchset (patches 2-7) improve the USB core's warm
reset error handling.
There's also one patch that fixes an arithmetic error in the xHCI
driver, and another to avoid the "dead ports" issue caused by
unhandled port status change events.
These are all marked for stable.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9YSo
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2013-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah says:
usb-linus: USB core fixes for warm reset
Hi Greg,
Happy New Year! Here's some bug fixes for 3.8. I have usb-next
patches that are based on this set, so please merge your usb-linus
branch into usb-next after this set is applied.
The bulk of the patchset (patches 2-7) improve the USB core's warm
reset error handling.
There's also one patch that fixes an arithmetic error in the xHCI
driver, and another to avoid the "dead ports" issue caused by
unhandled port status change events.
These are all marked for stable.
Sarah Sharp
Here is the first set of fixes for v3.8-rc cycle.
There is a build fix for musb's dsps glue layer caused
by some header cleanup on the OMAP tree.
Marvel's USB drivers got a fix up for clk API usage
switching over to clk_prepare() calls.
u_serial has a bug fix for a missing wake_up() which
would make gs_cleanup() wait forever for gs_close()
to finish.
A minor bug fix on dwc3's debugfs interface which
would make us read wrong addresses when dumping
all registers.
dummy_hcd learned how to enumerate g_multi.
s3c-hsotg now understands that we shouldn't kfree()
memory allocated with devm_*.
Other than that, there are a bunch of other minor fixes
on renesas_usbhs, tcm_usb_gadget and amd5536udc.
All patches have been pending on mailing for many weeks
and shouldn't cause any problems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UsKi
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe says:
usb: fixes for v3.8-rc2
Here is the first set of fixes for v3.8-rc cycle.
There is a build fix for musb's dsps glue layer caused
by some header cleanup on the OMAP tree.
Marvel's USB drivers got a fix up for clk API usage
switching over to clk_prepare() calls.
u_serial has a bug fix for a missing wake_up() which
would make gs_cleanup() wait forever for gs_close()
to finish.
A minor bug fix on dwc3's debugfs interface which
would make us read wrong addresses when dumping
all registers.
dummy_hcd learned how to enumerate g_multi.
s3c-hsotg now understands that we shouldn't kfree()
memory allocated with devm_*.
Other than that, there are a bunch of other minor fixes
on renesas_usbhs, tcm_usb_gadget and amd5536udc.
All patches have been pending on mailing for many weeks
and shouldn't cause any problems.
The union xhci_trb *trb variable is defined and assigned
inside the xHCI IRQ handler function but is never used.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Refactor hub_port_wait_reset into a small loop to wait for the port
reset to be complete, and then a larger block to deal with the final
port status. This patch should not change any current behavior.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Change the code that manually issues a Set Port Feature(Link State) to
use the new helper function hub_set_port_link_state().
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
A USB 3.0 device can transition to the Inactive state if a U1 or U2 exit
transition fails. The current code in hub_events simply issues a warm
reset, but does not call any pre-reset or post-reset driver methods (or
unbind/rebind drivers without them). Therefore the drivers won't know
their device has just been reset.
hub_events should instead call usb_reset_device. This means
hub_port_reset now needs to figure out whether it should issue a warm
reset or a hot reset.
Remove the FIXME note about needing disconnect() for a NOTATTACHED
device. This patch fixes that.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
When a hot reset fails on a USB 3.0 port, the current port reset code
recursively calls hub_port_reset inside hub_port_wait_reset. This isn't
ideal, since we should avoid recursive calls in the kernel, and it also
doesn't allow us to issue multiple warm resets on reset failures.
Rip out the recursive call. Instead, add code to hub_port_reset to
issue a warm reset if the hot reset fails, and try multiple warm resets
before giving up on the port.
In hub_port_wait_reset, remove the recursive call and re-indent. The
code is basically the same, except:
1. It bails out early if the port has transitioned to Inactive or
Compliance Mode after the reset completed.
2. It doesn't consider a connect status change to be a failed reset. If
multiple warm resets needed to be issued, the connect status may have
changed, so we need to ignore that and look at the port link state
instead. hub_port_reset will now do that.
3. It unconditionally sets udev->speed on all types of successful
resets. The old recursive code would set the port speed when the second
hub_port_reset returned.
The old code did not handle connected devices needing a warm reset well.
There were only two situations that the old code handled correctly: an
empty port needing a warm reset, and a hot reset that migrated to a warm
reset.
When an empty port needed a warm reset, hub_port_reset was called with
the warm variable set. The code in hub_port_finish_reset would skip
telling the USB core and the xHC host that the device was reset, because
otherwise that would result in a NULL pointer dereference.
When a USB 3.0 device reset migrated to a warm reset, the recursive call
made the call stack look like this:
hub_port_reset(warm = false)
hub_wait_port_reset(warm = false)
hub_port_reset(warm = true)
hub_wait_port_reset(warm = true)
hub_port_finish_reset(warm = true)
(return up the call stack to the first wait)
hub_port_finish_reset(warm = false)
The old code didn't want to notify the USB core or the xHC host of device reset
twice, so it only did it in the second call to hub_port_finish_reset,
when warm was set to false. This was necessary because
before patch two ("USB: Ignore xHCI Reset Device status."), the USB core
would pay attention to the xHC Reset Device command error status, and
the second call would always fail.
Now that we no longer have the recursive call, and warm can change from
false to true in hub_port_reset, we need to have hub_port_finish_reset
unconditionally notify the USB core and the xHC of the device reset.
In hub_port_finish_reset, unconditionally clear the connect status
change (CSC) bit for USB 3.0 hubs when the port reset is done. If we
had to issue multiple warm resets for a device, that bit may have been
set if the device went into SS.Inactive and then was successfully warm
reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The next patch will refactor the hub port code to rip out the recursive
call to hub_port_reset on a failed hot reset. In preparation for that,
make sure all code paths can deal with being called with a NULL udev.
The usb_device will not be valid if warm reset was issued because a port
transitioned to the Inactive or Compliance Mode on a device connect.
This patch should have no effect on current behavior.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The EHCI host controller needs to prevent EHCI initialization when the
UHCI or OHCI companion controller is in the middle of a port reset. It
uses ehci_cf_port_reset_rwsem to do this. USB 3.0 hubs can't be under
an EHCI host controller, so it makes no sense to down the semaphore for
USB 3.0 hubs. It also makes the warm port reset code more complex.
Don't down ehci_cf_port_reset_rwsem for USB 3.0 hubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The USB core hub thread (khubd) is designed with external USB hubs in
mind. It expects that if a port status change bit is set, the hub will
continue to send a notification through the hub status data transfer.
Basically, it expects hub notifications to be level-triggered.
The xHCI host controller is designed to be edge-triggered on the logical
'OR' of all the port status change bits. When all port status change
bits are clear, and a new change bit is set, the xHC will generate a
Port Status Change Event. If another change bit is set in the same port
status register before the first bit is cleared, it will not send
another event.
This means that the hub code may lose port status changes because of
race conditions between clearing change bits. The user sees this as a
"dead port" that doesn't react to device connects.
The fix is to turn on port polling whenever a new change bit is set.
Once the USB core issues a hub status request that shows that no change
bits are set in any USB ports, turn off port polling.
We can't allow the USB core to poll the roothub for port events during
host suspend because if the PCI host is in D3cold, the port registers
will be all f's. Instead, stop the port polling timer, and
unconditionally restart it when the host resumes. If there are no port
change bits set after the resume, the first call to hub_status_data will
disable polling.
This patch should be backported to stable kernels with the first xHCI
support, 2.6.31 and newer, that include the commit
0f2a79300a "USB: xhci: Root hub support."
There will be merge conflicts because the check for HC_STATE_SUSPENDED
was moved into xhci_suspend in 3.8.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
An empty port can transition to either Inactive or Compliance Mode if a
newly connected USB 3.0 device fails to link train. In that case, we
issue a warm reset. Some devices, such as John's Roseweil eusb3
enclosure, slip back into Compliance Mode after the warm reset.
The current warm reset code does not check for device connect status on
warm reset completion, and it incorrectly reports the warm reset
succeeded. This causes the USB core to attempt to send a Set Address
control transfer to a port in Compliance Mode, which will always fail.
Make hub_port_wait_reset check the current connect status and link state
after the warm reset completes. Return a failure status if the device
is disconnected or the link state is Compliance Mode or SS.Inactive.
Make hub_events disable the port if warm reset fails. This will disable
the port, and then bring it back into the RxDetect state. Make the USB
core ignore the connect change until the device reconnects.
Note that this patch does NOT handle connected devices slipping into the
Inactive state very well. This is a concern, because devices can go
into the Inactive state on U1/U2 exit failure. However, the fix for
that case is too large for stable, so it will be submitted in a separate
patch.
This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab "usbcore: refine warm
reset logic"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
The port reset code bails out early if the current connect status is
cleared (device disconnected). If we're issuing a hot reset, it may
also look at the link state before the reset is finished.
Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the
Error state or Resetting state, the port connection bit retains the
value from the previous state. Therefore we can't trust it until the
reset finishes. Also, the xHCI spec section 4.19.1.2.5 says software
shall ignore the link state while the port is resetting, as it can be in
an unknown state.
The port state during reset is also unknown for USB 2.0 hubs. The hub
sends a reset signal by driving the bus into an SE0 state. This
overwhelms the "connect" signal from the device, so the port can't tell
whether anything is connected or not.
Fix the port reset code to ignore the port link state and current
connect bit until the reset finishes, and USB_PORT_STAT_RESET is
cleared.
Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case,
because it's redundant. When the warm reset finishes, the port reset
bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set.
Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit
in the code to deal with the finished reset.
This patch should be backported to all stable kernels.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
John's NEC 0.96 xHCI host controller needs a longer timeout for a warm
reset to complete. The logs show it takes 650ms to complete the warm
reset, so extend the hub reset timeout to 800ms to be on the safe side.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
If hot and warm reset fails, or a port remains in the Compliance Mode,
the USB core needs to be able to disable a USB 3.0 port. Unlike USB 2.0
ports, once the port is placed into the Disabled link state, it will not
report any new device connects. To get device connect notifications, we
need to put the link into the Disabled state, and then the RxDetect
state.
The xHCI driver needs to atomically clear all change bits on USB 3.0
port disable, so that we get Port Status Change Events for future port
changes. We could technically do this in the USB core instead of in the
xHCI roothub code, since the port state machine can't advance out of the
disabled state until we set the link state to RxDetect. However,
external USB 3.0 hubs don't need this code. They are level-triggered,
not edge-triggered like xHCI, so they will continue to send interrupt
events when any change bit is set. Therefore it doesn't make sense to
put this code in the USB core.
This patch is part of a series to fix several reports of infinite loops
on device enumeration failure. This includes John, when he boots with
a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96
host controller. The fix requires warm reset support, so it does not
make sense to backport this patch to stable kernels without warm reset
support.
This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab "usbcore: refine warm
reset logic"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
When the USB core finishes reseting a USB device, the xHCI driver sends
a Reset Device command to the host. The xHC then updates its internal
representation of the USB device to the 'Default' device state. If the
device was already in the Default state, the xHC will complete the
command with an error status.
If a device needs to be reset several times during enumeration, the
second reset will always fail because of the xHCI Reset Device command.
This can cause issues during enumeration.
For example, usb_reset_and_verify_device calls into hub_port_init in a
loop. Say that on the first call into hub_port_init, the device is
successfully reset, but doesn't respond to several set address control
transfers. Then the port will be disabled, but the udev will remain in
tact. usb_reset_and_verify_device will call into hub_port_init again.
On the second call into hub_port_init, the device will be reset, and the
xHCI driver will issue a Reset Device command. This command will fail
(because the device is already in the Default state), and
usb_reset_and_verify_device will fail. The port will be disabled, and
the device won't be able to enumerate.
Fix this by ignoring the return value of the HCD reset_device callback.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
USB 3.0 hubs and roothubs will automatically transition a failed hot
reset to a warm (BH) reset. In that case, the warm reset change bit
will be set, and the link state change bit may also be set. Change
hub_port_finish_reset to unconditionally clear those change bits for USB
3.0 hubs. If these bits are not cleared, we may lose port change events
from the roothub.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK. If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).
The xHCI code to compute the NAK interval does not handle the special
case of zero properly. The current code unconditionally subtracts one
from bInterval and uses it as an exponent. This causes a very large
bInterval to be used, and warning messages like these will be printed:
usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes
This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.
This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4ad1 "USB: xhci - fix math in
xhci_get_endpoint_interval()".
Reported-by: Vincent Pelletier <plr.vincent@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Pull LED fix from Bryan Wu.
* 'fixes-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: leds-gpio: set devm_gpio_request_one() flags param correctly
commit a99d76f leds: leds-gpio: use gpio_request_one
changed the leds-gpio driver to use gpio_request_one() instead
of gpio_request() + gpio_direction_output()
Unfortunately, it also made a semantic change that breaks the
leds-gpio driver.
The gpio_request_one() flags parameter was set to:
GPIOF_DIR_OUT | (led_dat->active_low ^ state)
Since GPIOF_DIR_OUT is 0, the final flags value will just be the
XOR'ed value of led_dat->active_low and state.
This value were used to distinguish between HIGH/LOW output initial
level and call gpio_direction_output() accordingly.
With this new semantic gpio_request_one() will take the flags value
of 1 as a configuration of input direction (GPIOF_DIR_IN) and will
call gpio_direction_input() instead of gpio_direction_output().
int gpio_request_one(unsigned gpio, unsigned long flags, const char *label)
{
..
if (flags & GPIOF_DIR_IN)
err = gpio_direction_input(gpio);
else
err = gpio_direction_output(gpio,
(flags & GPIOF_INIT_HIGH) ? 1 : 0);
..
}
The right semantic is to evaluate led_dat->active_low ^ state and
set the output initial level explicitly.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reported-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes some small errors in the new da9055 driver, eliminates a
compiler warning and adds DT support for the twl4030_wdt driver (so
that we can have multiple watchdogs with DT on the omap platforms)."
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: twl4030_wdt: add DT support
watchdog: omap_wdt: eliminate unused variable and a compiler warning
watchdog: da9055: Don't update wdt_dev->timeout in da9055_wdt_set_timeout error path
watchdog: da9055: Fix invalid free of devm_ allocated data
PCI: Reduce Ricoh 0xe822 SD card reader base clock frequency to 50MHz
PCI: Remove spurious error for sriov_numvfs store and simplify flow
PCI: Add PCIe Link Capability link speed and width names
PCI/PM: Do not suspend port if any subordinate device needs PME polling
PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=Ehs+
-----END PGP SIGNATURE-----
Merge tag '3.8-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Some fixes for v3.8. They include a fix for the new SR-IOV sysfs
management support, an expanded quirk for Ricoh SD card readers, a
Stratus DMI quirk fix, and a PME polling fix."
* tag '3.8-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Reduce Ricoh 0xe822 SD card reader base clock frequency to 50MHz
PCI/PM: Do not suspend port if any subordinate device needs PME polling
PCI: Add PCIe Link Capability link speed and width names
PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)
PCI: Remove spurious error for sriov_numvfs store and simplify flow
Commit 56c176c9ca ("UAPI: strip the _UAPI prefix from header guards
during header installation") strips the _UAPI prefix from header guards,
but only if there's a single space between the cpp directive and the
label.
Make it more flexible and able to handle tabs and multiple white space
characters.
Signed-off-by: David Howells <dhowell@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Empty files can get deleted by the patch program, so remove empty Kbuild
files and their links from the parent Kbuilds.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
overwriting a full page in the eCryptfs page cache, skip reading in and
decrypting the corresponding lower page.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JNeQ
-----END PGP SIGNATURE-----
Merge tag 'ecryptfs-3.8-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Two self-explanatory fixes and a third patch which improves
performance: when overwriting a full page in the eCryptfs page cache,
skip reading in and decrypting the corresponding lower page."
* tag 'ecryptfs-3.8-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
fs/ecryptfs/crypto.c: make ecryptfs_encode_for_filename() static
eCryptfs: fix to use list_for_each_entry_safe() when delete items
eCryptfs: Avoid unnecessary disk read and data decryption during writing
Pull Ceph fixes from Sage Weil:
"Two of Alex's patches deal with a race when reseting server
connections for open RBD images, one demotes some non-fatal BUGs to
WARNs, and my patch fixes a protocol feature bit failure path."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: fix protocol feature mismatch failure path
libceph: WARN, don't BUG on unexpected connection states
libceph: always reset osds when kicking
libceph: move linger requests sooner in kick_requests()
Sasha was fuzzing with trinity and reported the following problem:
BUG: sleeping function called from invalid context at kernel/mutex.c:269
in_atomic(): 1, irqs_disabled(): 0, pid: 6361, name: trinity-main
2 locks held by trinity-main/6361:
#0: (&mm->mmap_sem){++++++}, at: [<ffffffff810aa314>] __do_page_fault+0x1e4/0x4f0
#1: (&(&mm->page_table_lock)->rlock){+.+...}, at: [<ffffffff8122f017>] handle_pte_fault+0x3f7/0x6a0
Pid: 6361, comm: trinity-main Tainted: G W
3.7.0-rc2-next-20121024-sasha-00001-gd95ef01-dirty #74
Call Trace:
__might_sleep+0x1c3/0x1e0
mutex_lock_nested+0x29/0x50
mpol_shared_policy_lookup+0x2e/0x90
shmem_get_policy+0x2e/0x30
get_vma_policy+0x5a/0xa0
mpol_misplaced+0x41/0x1d0
handle_pte_fault+0x465/0x6a0
This was triggered by a different version of automatic NUMA balancing
but in theory the current version is vunerable to the same problem.
do_numa_page
-> numa_migrate_prep
-> mpol_misplaced
-> get_vma_policy
-> shmem_get_policy
It's very unlikely this will happen as shared pages are not marked
pte_numa -- see the page_mapcount() check in change_pte_range() -- but
it is possible.
To address this, this patch restores sp->lock as originally implemented
by Kosaki Motohiro. In the path where get_vma_policy() is called, it
should not be calling sp_alloc() so it is not necessary to treat the PTL
specially.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
which could cause file system corruptions when performing file punch
operations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=9R/D
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Various bug fixes for ext4. Perhaps the most serious bug fixed is one
which could cause file system corruptions when performing file punch
operations."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid hang when mounting non-journal filesystems with orphan list
ext4: lock i_mutex when truncating orphan inodes
ext4: do not try to write superblock on ro remount w/o journal
ext4: include journal blocks in df overhead calcs
ext4: remove unaligned AIO warning printk
ext4: fix an incorrect comment about i_mutex
ext4: fix deadlock in journal_unmap_buffer()
ext4: split off ext4_journalled_invalidatepage()
jbd2: fix assertion failure in jbd2_journal_flush()
ext4: check dioread_nolock on remount
ext4: fix extent tree corruption caused by hole punch
Remove the unused argument (formerly no_context) from mpol_parse_str()
and from mpol_to_str().
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently I suggested using "mount -o remount,mpol=local /tmp" in NUMA
mempolicy testing. Very nasty. Reading /proc/mounts, /proc/pid/mounts
or /proc/pid/mountinfo may then corrupt one bit of kernel memory, often
in a page table (causing "Bad swap" or "Bad page map" warning or "Bad
pagetable" oops), sometimes in a vm_area_struct or rbnode or somewhere
worse. "mpol=prefer" and "mpol=prefer:Node" are equally toxic.
Recent NUMA enhancements are not to blame: this dates back to 2.6.35,
when commit e17f74af35 "mempolicy: don't call mpol_set_nodemask() when
no_context" skipped mpol_parse_str()'s call to mpol_set_nodemask(),
which used to initialize v.preferred_node, or set MPOL_F_LOCAL in flags.
With slab poisoning, you can then rely on mpol_to_str() to set the bit
for node 0x6b6b, probably in the next page above the caller's stack.
mpol_parse_str() is only called from shmem_parse_options(): no_context
is always true, so call it unused for now, and remove !no_context code.
Set v.nodes or v.preferred_node or MPOL_F_LOCAL as mpol_to_str() might
expect. Then mpol_to_str() can ignore its no_context argument also,
the mpol being appropriately initialized whether contextualized or not.
Rename its no_context unused too, and let subsequent patch remove them
(that's not needed for stable backporting, which would involve rejects).
I don't understand why MPOL_LOCAL is described as a pseudo-policy:
it's a reasonable policy which suffers from a confusing implementation
in terms of MPOL_PREFERRED with MPOL_F_LOCAL. I believe this would be
much more robust if MPOL_LOCAL were recognized in switch statements
throughout, MPOL_F_LOCAL deleted, and MPOL_PREFERRED use the (possibly
empty) nodes mask like everyone else, instead of its preferred_node
variant (I presume an optimization from the days before MPOL_LOCAL).
But that would take me too long to get right and fully tested.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EPOLL_CTL_MOD sets the interest mask before calling f_op->poll() to
ensure events are not missed. Since the modifications to the interest
mask are not protected by the same lock as ep_poll_callback, we need to
ensure the change is visible to other CPUs calling ep_poll_callback.
We also need to ensure f_op->poll() has an up-to-date view of past
events which occured before we modified the interest mask. So this
barrier also pairs with the barrier in wq_has_sleeper().
This should guarantee either ep_poll_callback or f_op->poll() (or both)
will notice the readiness of a recently-ready/modified item.
This issue was encountered by Andreas Voellmy and Junchang(Jason) Wang in:
http://thread.gmane.org/gmane.linux.kernel/1408782/
Signed-off-by: Eric Wong <normalperson@yhbt.net>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andreas Voellmy <andreas.voellmy@yale.edu>
Tested-by: "Junchang(Jason) Wang" <junchang.wang@yale.edu>
Cc: netdev@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to
probe when booting with DT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We forgot to delete this in the commit 4f4753d9 (watchdog: omap_wdt:
convert to devm_ functions), and as a result the following compilation
warning was introduced:
drivers/watchdog/omap_wdt.c: In function 'omap_wdt_remove':
drivers/watchdog/omap_wdt.c:299:19: warning: unused variable 'res' [-Wunused-variable]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Otherwise, WDIOC_GETTIMEOUT returns wrong value if set_timeout fails.
This patch also removes unnecessary ret variable in da9055_wdt_ping function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is not required to free devm_ allocated data. Since kref_put
needs a valid release function, da9055_wdt_release_resources()
is not deleted.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull DRM update from Dave Airlie:
"This is a bit larger due to me not bothering to do anything since
before Xmas, and other people working too hard after I had clearly
given up.
It's got the 3 main x86 driver fixes pulls, and a bunch of tegra
fixes, doesn't fix the Ironlake bug yet, but that does seem to be
getting closer.
- radeon: gpu reset fixes and userspace packet support
- i915: watermark fixes, workarounds, i830/845 fix,
- nouveau: nvd9/kepler microcode fixes, accel is now enabled and
working, gk106 support
- tegra: misc fixes."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (34 commits)
Revert "drm: tegra: protect DC register access with mutex"
drm: tegra: program only one window during modeset
drm: tegra: clean out old gem prototypes
drm: tegra: remove redundant tegra2_tmds_config entry
drm: tegra: protect DC register access with mutex
drm: tegra: don't leave clients host1x member uninitialized
drm: tegra: fix front_porch <-> back_porch mixup
drm/nve0/graph: fix fuc, and enable acceleration on all known chipsets
drm/nvc0/graph: fix fuc, and enable acceleration on GF119
drm/nouveau/bios: cache ramcfg strap on later chipsets
drm/nouveau/mxm: silence output if no bios data
drm/nouveau/bios: parse/display extra version component
drm/nouveau/bios: implement opcode 0xa9
drm/nouveau/bios: update gpio parsing apis to match current design
drm/nouveau: initial support for GK106
drm/radeon: add WAIT_UNTIL to evergreen VM safe reg list
drm/i915: disable shrinker lock stealing for create_mmap_offset
drm/i915: optionally disable shrinker lock stealing
drm/i915: fix flags in dma buf exporting
drm/radeon: add support for MEM_WRITE packet
...
From Tony Lindgren:
Here are few more patches to finish the omap changes for
multiplatform conversion that are not strictly fixes, but
were too complex to do with the dependencies during the
merge window. Those are to move of serial-omap.h to
platform_data, and the removal of remaining cpu_is_omap
macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few
minimal omap2plus_defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RE6Z
-----END PGP SIGNATURE-----
Merge tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM cleanups for omap from Olof Johansson:
"From Tony Lindgren:
Here are few more patches to finish the omap changes for multiplatform
conversion that are not strictly fixes, but were too complex to do
with the dependencies during the merge window. Those are to move of
serial-omap.h to platform_data, and the removal of remaining
cpu_is_omap macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few minimal
omap2plus_defconfig updates."
* tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-omap2/dpll3xxx.c: drop if around WARN_ON
OMAP2: Fix a typo - replace regist with register.
ARM/omap: use module_platform_driver macro
ARM: OMAP2+: PMU: Remove unused header
ARM: OMAP4: remove duplicated include from omap_hwmod_44xx_data.c
ARM: OMAP2+: omap2plus_defconfig: enable twl4030 SoC audio
ARM: OMAP2+: omap2plus_defconfig: Add tps65217 support
ARM: OMAP2+: enable devtmpfs and devtmpfs automount
ARM: OMAP2+: omap_twl: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
ARM: OMAP2+: Drop plat/cpu.h for omap2plus
ARM: OMAP: Split fb.c to remove last remaining cpu_is_omap usage
MAINTAINERS: Add an entry for omap related .dts files
It's been quiet over the holidays, but we have had a couple of trivial
fixes coming in for the newly introduced sunxi platform; one to add it
to the multiplatform defconfig for build coverage, and one fixup for
device tree strings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9cQy
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"It's been quiet over the holidays, but we have had a couple of trivial
fixes coming in for the newly introduced sunxi platform; one to add it
to the multiplatform defconfig for build coverage, and one fixup for
device tree strings."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
sunxi: Change the machine compatible string.
ARM: multi_v7_defconfig: Add ARCH_SUNXI
Sebastian Andrzej Siewior