Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
- Not a single new clocksource or clockevent driver!
- Device tree updates for various chips
- Fixes and improvements and cleanups all over the place
-----BEGIN PGP SIGNATURE-----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=FFm0
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The truly boring timer and clocksource updates for 5.8:
- Not a single new clocksource or clockevent driver!
- Device tree updates for various chips
- Fixes and improvements and cleanups all over the place"
* tag 'timers-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
dt-bindings: timer: Add renesas,em-sti bindings
clocksource/drivers/timer-versatile: Clear OF_POPULATED flag
clocksource: mips-gic-timer: Mark GIC timer as unstable if ref clock changes
clocksource: mips-gic-timer: Register as sched_clock
clocksource: dw_apb_timer_of: Fix missing clockevent timers
clocksource: dw_apb_timer: Affiliate of-based timer with any CPU
clocksource: dw_apb_timer: Make CPU-affiliation being optional
dt-bindings: timer: Move snps,dw-apb-timer DT schema from rtc
dt-bindings: rtc: Convert snps,dw-apb-timer to DT schema
clocksource/drivers/timer-ti-dm: Do one override clock parent in prepare()
clocksource/drivers/timer-ti-dm: Fix spelling mistake "detectt" -> "detect"
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
drivers/clocksource/arm_arch_timer: Remove duplicate error message
clocksource/drivers/arc_timer: Remove duplicate error message
clocksource/drivers/rda: drop redundant Kconfig dependency
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
...
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
-----BEGIN PGP SIGNATURE-----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=vMHE
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8980/1: Allow either FLATMEM or SPARSEMEM on the multiplatform build
ARM: 8979/1: Remove redundant ARCH_SPARSEMEM_DEFAULT setting
ARM: 8978/1: mm: make act_mm() respect THREAD_SIZE
ARM: decompressor: run decompressor in place if loaded via UEFI
ARM: decompressor: move GOT into .data for EFI enabled builds
ARM: decompressor: defer loading of the contents of the LC0 structure
ARM: decompressor: split off _edata and stack base into separate object
ARM: decompressor: move headroom variable out of LC0
ARM: 8976/1: module: allow arch overrides for .init section names
ARM: 8975/1: module: fix handling of unwind init sections
ARM: 8974/1: use SPARSMEM_STATIC when SPARSEMEM is enabled
ARM: 8971/1: replace the sole use of a symbol with its definition
ARM: 8969/1: decompressor: simplify libfdt builds
Update rmk's email address in various drivers
ARM: compat: remove KERNEL_DS usage in sys_oabi_epoll_ctl()
- preliminary changes for RISC-V
- Add support for setting the resolution on the EFI framebuffer
- Simplify kernel image loading for arm64
- Move .bss into .data via the linker script instead of relying on symbol
annotations.
- Get rid of __pure getters to access global variables
- Clean up the config table matching arrays
- Rename pr_efi/pr_efi_err to efi_info/efi_err, and use them consistently
- Simplify and unify initrd loading
- Parse the builtin command line on x86 (if provided)
- Implement printk() support, including support for wide character strings
- Simplify GDT handling in early mixed mode thunking code
- Some other minor fixes and cleanups
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XG4E
-----END PGP SIGNATURE-----
Merge tag 'efi-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Ingo Molnar:
"The EFI changes for this cycle are:
- preliminary changes for RISC-V
- Add support for setting the resolution on the EFI framebuffer
- Simplify kernel image loading for arm64
- Move .bss into .data via the linker script instead of relying on
symbol annotations.
- Get rid of __pure getters to access global variables
- Clean up the config table matching arrays
- Rename pr_efi/pr_efi_err to efi_info/efi_err, and use them
consistently
- Simplify and unify initrd loading
- Parse the builtin command line on x86 (if provided)
- Implement printk() support, including support for wide character
strings
- Simplify GDT handling in early mixed mode thunking code
- Some other minor fixes and cleanups"
* tag 'efi-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
efi/x86: Don't blow away existing initrd
efi/x86: Drop the special GDT for the EFI thunk
efi/libstub: Add missing prototype for PE/COFF entry point
efi/efivars: Add missing kobject_put() in sysfs entry creation error path
efi/libstub: Use pool allocation for the command line
efi/libstub: Don't parse overlong command lines
efi/libstub: Use snprintf with %ls to convert the command line
efi/libstub: Get the exact UTF-8 length
efi/libstub: Use %ls for filename
efi/libstub: Add UTF-8 decoding to efi_puts
efi/printf: Add support for wchar_t (UTF-16)
efi/gop: Add an option to list out the available GOP modes
efi/libstub: Add definitions for console input and events
efi/libstub: Implement printk-style logging
efi/printf: Turn vsprintf into vsnprintf
efi/printf: Abort on invalid format
efi/printf: Refactor code to consolidate padding and output
efi/printf: Handle null string input
efi/printf: Factor out integer argument retrieval
efi/printf: Factor out width/precision parsing
...
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
This time there is one fix for the error path in the mediatek cmdq driver
(used by their video driver) and a couple of devicetree fixes, mostly
for 32-bit ARM, and fairly harmless:
- On OMAP2 there were a few regressions in the ethernet drivers,
one of them leading to an external abort trap
- One Raspberry Pi version had a misconfigured LED
- Interrupts on Broadcom NSP were slightly misconfigured
- One i.MX6q board had issues with graphics mode setting
- On mmp3 there are some minor fixes that were submitted for
v5.8 with a cc:stable tag, so I ended up picking them up
here as well
- The Mediatek Video Codec needs to run at a higher frequency
than configured originally
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl7Rin0ACgkQmmx57+YA
GNlD7A//ehGZi+AinBWiCupunm26EekqJE2hp8gZMCYAil5jm3Djk4oib6xHFSIB
+z6H0gXfi/cqeMNkch3aPW0Rhqm6JhvOpkVmBEzwXSj1W9TQz6Xvhy58Aa3E1h/A
2FyoC4pm9hKOlamaEUkaOLblMhLRla1fpgewmB6qGPNWZx6gNX45cxawqn9t4M7/
tjDa9s+Df8YxeS08thK6PVwZ3zdVQLFfhuZR0/tCpBgikYSuK+e9W9R7IealPPs5
iPTBeFpJVbtapaEaXHyjlyUn+0TdiEq5nrFwv6vMc08kIrZl9Ej9DSel0pq+mEDT
b/v5J3FBgcq20kTBfeU2fYw5Sr6bZ7Ojm0ZMnFou60CPX7R18FDbgl8+ISOK8wmV
1m+0V+tNYg7Mxu0IXBTHuZ98oMH3YeFmmYUOUIp5wmxHH/wsAePUxroRQXDZHtBA
XEAN4qOztNtNrz1+iKwe03tls50baF0oey0N6AqH+yH6DvBbbIRYZxgAvErdh8YU
67hbKnhYpK7gsGeCJ/f056TKUizsX923pU6e5XapdG9bNXLm5lgC2dSA2iPJjws/
ppcbQjQTef1j2MPs97Al0Q3wbPTiq4dM0na1B//iyBZOAQf3niZPaUdbPngbNCra
FZmVhdKkhI7EAIBAS+9haK/v6RKrMJytJd6z6o4GTRL0CElahdw=
=E8Pg
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This time there is one fix for the error path in the mediatek cmdq
driver (used by their video driver) and a couple of devicetree fixes,
mostly for 32-bit ARM, and fairly harmless:
- On OMAP2 there were a few regressions in the ethernet drivers, one
of them leading to an external abort trap
- One Raspberry Pi version had a misconfigured LED
- Interrupts on Broadcom NSP were slightly misconfigured
- One i.MX6q board had issues with graphics mode setting
- On mmp3 there are some minor fixes that were submitted for v5.8
with a cc:stable tag, so I ended up picking them up here as well
- The Mediatek Video Codec needs to run at a higher frequency than
configured originally"
* tag 'armsoc-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
ARM: dts/imx6q-bx50v3: Set display interface clock parents
soc: mediatek: cmdq: return send msg error code
arm64: dts: mt8173: fix vcodec-enc clock
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
Enable ethernet wake-on-lan feature for imx6q/dl/qp sabresd
boards since the PHY clock is supplied by external osc.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update the imx6qdl gpr property to define gpr register
offset and bit in DT.
- Add imx6sx/imx6ul/imx7d ethernet stop mode property.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- correct value of decompressor tag size in header
- fix DACR value when we have nested exceptions
- fix a missing newline on a kernel message
- fix mask for ptrace thumb breakpoint hook
-----BEGIN PGP SIGNATURE-----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=dAx4
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- correct value of decompressor tag size in header
- fix DACR value when we have nested exceptions
- fix a missing newline on a kernel message
- fix mask for ptrace thumb breakpoint hook
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8977/1: ptrace: Fix mask for thumb breakpoint hook
ARM: 8973/1: Add missing newline terminator to kernel message
ARM: uaccess: fix DACR mismatch with nested exceptions
ARM: uaccess: integrate uaccess_save and uaccess_restore
ARM: uaccess: consolidate uaccess asm to asm/uaccess-asm.h
ARM: 8970/1: decompressor: increase tag size
Recent cpsw driver changes exposed few regressions in the cpsw related
dts configuration that would be good to fix:
- Few more boards still need to be updated to use rgmii-rxid phy caused
by the fallout from commit bcf3440c6d ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY" as the rx delay is now disabled unless we
use rgmii-rxid.
- On dm814x we have been using a wrong clock for mdio that now can produce
external abort on some boards
-----BEGIN PGP SIGNATURE-----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=tWSS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/cpsw-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few cpsw related dts fixes for omaps
Recent cpsw driver changes exposed few regressions in the cpsw related
dts configuration that would be good to fix:
- Few more boards still need to be updated to use rgmii-rxid phy caused
by the fallout from commit bcf3440c6d ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY" as the rx delay is now disabled unless we
use rgmii-rxid.
- On dm814x we have been using a wrong clock for mdio that now can produce
external abort on some boards
* tag 'omap-for-v5.7/cpsw-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
Link: https://lore.kernel.org/r/pull-1589472123-367692@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Rename pr_efi/pr_efi_err to efi_info/efi_err, and use them consistently
- Simplify and unify initrd loading
- Parse the builtin command line on x86 (if provided)
- Implement printk() support, including support for wide character strings
- Some fixes for issues introduced by the first batch of v5.8 changes
- Fix a missing prototypes warning
- Simplify GDT handling in early mixed mode thunking code
- Some other minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEnNKg2mrY9zMBdeK7wjcgfpV0+n0FAl7Lb8UACgkQwjcgfpV0
+n3/aAgAkEqqR/BoyzFiyYHujq6bXjESKYr8LrIjNWfnofB6nZqp1yXwFdL0qbj/
PTZ1qIQAnOMmj11lvy1X894h2ZLqE6XEkqv7Xd2oxkh3fF6amlQUWfMpXUuGLo1k
C4QGSfA0OOiM0OOi0Aqk1fL7sTmH23/j63dTR+fH8JMuYgjdls/yWNs0miqf8W2H
ftj8fAKgHIJzFvdTC0vn1DZ6dEKczGLPEcVZ2ns2IJOJ69DsStKPLcD0mlW+EgV2
EyfRSCQv55RYZRhdUOb+yVLRfU0M0IMDrrCDErHxZHXnQy00tmKXiEL20yuegv3u
MUtRRw8ocn2/RskjgZkxtMjAAlty9A==
=AwCh
-----END PGP SIGNATURE-----
Merge tag 'efi-changes-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/core
More EFI changes for v5.8:
- Rename pr_efi/pr_efi_err to efi_info/efi_err, and use them consistently
- Simplify and unify initrd loading
- Parse the builtin command line on x86 (if provided)
- Implement printk() support, including support for wide character strings
- Some fixes for issues introduced by the first batch of v5.8 changes
- Fix a missing prototypes warning
- Simplify GDT handling in early mixed mode thunking code
- Some other minor fixes and cleanups
Conflicts:
drivers/firmware/efi/libstub/efistub.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
5.7, please pull the following:
- Vincent fixes the polarity of the ACT LED on the Raspberry Pi Zero W
board
- Hamish fixes the ARM PPI interrupts sensitivy for the Hurricane 2
SoCs
-----BEGIN PGP SIGNATURE-----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=klA0
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.7/devicetree-fixes-part2-v2' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.7, please pull the following:
- Vincent fixes the polarity of the ACT LED on the Raspberry Pi Zero W
board
- Hamish fixes the ARM PPI interrupts sensitivy for the Hurricane 2
SoCs
* tag 'arm-soc/for-5.7/devicetree-fixes-part2-v2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
Link: https://lore.kernel.org/r/20200524203714.17035-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a missing prototype warning by adding a forward declaration
for the PE/COFF entrypoint, and while at it, align the function
name between the x86 and ARM versions of the stub.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
One imx6q-bx50v3 device tree change to fix an issue, attempting atomic
modeset while using HDMI and display port at the same time causes LDB
clock programming to destroy the programming of HDMI.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7Glo8UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5L1wf9ErUGnk73syGW6Hhr8VRRGocK8Zj7
Skh0E2k1ZT0YXRn5h6dikZw9TsR8IVt5CSt57NxvR61i4PnPm8PEBZdIl80kMu3P
3wO28Z4oIqhi9tzI+fM6uRV6WGxp5fIuwyEghAPpv0Xo/XKDbDQZkk/TtQDhqvVC
n7rjgk+N/x6kVTfRTYYIvI+XSoGM1lGdBl9DdAxKc2Suxr27qFcopYIE6JKsapoo
0khguE7v8BNG+N7iJ6tDXRcn4MV1TEDpTQ0cwZr1zIAiA3P5ZYKIGdweScVJ80fa
RGllUMBBrs7r0cNTpA8hu76omF2Kim0D8QsvLMDLELOijB4b/qBf2bU9AA==
=cAJG
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.7, round 2:
One imx6q-bx50v3 device tree change to fix an issue, attempting atomic
modeset while using HDMI and display port at the same time causes LDB
clock programming to destroy the programming of HDMI.
* tag 'imx-fixes-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts/imx6q-bx50v3: Set display interface clock parents
Link: https://lore.kernel.org/r/20200521150719.GB24084@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These three fixes should make it into linux-5.7 and
also into the branch for other mmp dt changes for v5.8,
so I created a branch for them.
* mmp/fixes:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
"usb-nop-xceiv" is good enough if we don't lose the configuration done
by the firmware, but we'd really prefer a real driver.
Unfortunately, the PHY core is odd in that when the node is compatible
with "usb-nop-xceiv", it ignores the other compatible strings. Let's
just remove it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I've managed to get about everything wrong while digging these out of
OEM's board file.
Correct the bus numbers, the exact model of the NOR flash, polarity of
the chip selects and align the SPI frequency with the data sheet.
Tested that it works now, with a slight fix to the PXA SSP driver.
Link: https://lore.kernel.org/r/20200419171157.672999-16-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Clocks are in fact slightly different on MMP3. In particular, PLL2 is
fixed to a different frequency, there's an extra PLL3, and the GPU
clocks are configured differently.
Link: https://lore.kernel.org/r/20200419171157.672999-15-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These error messages are output when booting on a BCM HR2 system:
GIC: PPI11 is secure or misconfigured
GIC: PPI13 is secure or misconfigured
Per ARM documentation these interrupts are triggered on a rising edge.
See ARM Cortex A-9 MPCore Technical Reference Manual, Revision r4p1,
Section 3.3.8 Interrupt Configuration Registers.
The same issue was resolved for NSP systems in commit 5f1aa51c7a
("ARM: dts: NSP: Fix PPI interrupt types").
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The status "ACT" led on the Raspberry Pi Zero W is on when GPIO 47 is low.
This has been verified on a board and somewhat confirmed by both the GPIO
name ("STATUS_LED_N") and the reduced schematics [1].
[1]: https://www.raspberrypi.org/documentation/hardware/raspberrypi/schematics/rpi_SCH_ZeroW_1p1_reduced.pdf
Fixes: 2c7c040c73 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates]
Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The decompressor can load from anywhere in memory, and the only reason
the EFI stub code relocates it is to ensure it appears within the first
128 MiB of memory, so that the uncompressed kernel ends up at the right
offset in memory.
We can short circuit this, and simply jump into the decompressor startup
code at the point where it knows where the base of memory lives. This
also means there is no need to disable the MMU and caches, create new
page tables and re-enable them.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
We will be running the decompressor in place after a future patch,
instead of copying it around first. This means we no longer have to
disable and re-enable the MMU and caches either. However, this means
we will be loaded with the restricted permissions set by the UEFI
firmware, which means that we have to move the GOT table into the
data section in order for the contents to be writable by the code
itself.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
The remaining contents of LC0 are only used after the point in the
decompressor startup code where we enter via 'wont_overwrite'. So
move the loading of the LC0 structure after it. This will allow us
to jump to wont_overwrite directly from the EFI stub, and execute
the decompressor in place at the offset it was loaded by the UEFI
firmware.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
In preparation of moving the handling of the LC0 object to a later stage
in the decompressor startup code, move out _edata and the initial value
of the stack pointer, which are needed earlier than the remaining
contents of LC0.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Before breaking up LC0 into different pieces, move out the variable
that is already place-relative (given that it subtracts 'restart' in
the expression) and so its value does not need to be added to the
runtime address of the LC0 symbol itself.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
- Fix a wrong clock configuration on R-Mobile A1,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXr5jTgAKCRCKwlD9ZEnx
cKSMAQCGIyrVtXHISZSFlp3poR1bBMejfxvZWmLIBzIPSw28SQEAqGTxP7dONrXY
JIbYmduRiRfWK6h0ghr769xp/KQPIAQ=
=dl06
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.7 (take two)
- Fix a wrong clock configuration on R-Mobile A1,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
* tag 'renesas-fixes-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: iwg20d-q7-dbcm-ca: Remove unneeded properties in hdmi@39
ARM: dts: renesas: Make hdmi encoder nodes compliant with DT bindings
arm64: dts: renesas: Make hdmi encoder nodes compliant with DT bindings
ARM: dts: r8a7740: Add missing extal2 to CPG node
Link: https://lore.kernel.org/r/20200515125043.22811-1-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove the adi,input-style and adi,input-justification properties of
hdmi@39 to make it compliant with the "adi,adv7511w" DT binding.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-6-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Small fixes to make these DTs compliant with the adi,adv7511w and
adi,adv7513 bindings:
r8a7745-iwg22d-sodimm-dbhd-ca.dts
r8a7790-lager.dts
r8a7790-stout.dts
r8a7791-koelsch.dts
r8a7791-porter.dts
r8a7792-blanche.dts
r8a7793-gose.dts
r8a7794-silk.dts:
Remove the adi,input-style and adi,input-justification properties.
r8a7792-wheat.dts:
Reorder the I2C slave addresses of hdmi@3d and hdmi@39 and remove
the adi,input-style and adi,input-justification properties.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-3-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Few device tree fixes for various devices:
- A regression fix for non-existing can device on am534x-idk
- Fix missing dma-ranges for dra7 pcie
- Fix flakey wlan on droid4 where some devices would not connect
at all because of internal pull being used with an external pull
- Fix occasional missed wake-up events on droid4 modem uart
-----BEGIN PGP SIGNATURE-----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=umsu
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.6-rc cycle
Few device tree fixes for various devices:
- A regression fix for non-existing can device on am534x-idk
- Fix missing dma-ranges for dra7 pcie
- Fix flakey wlan on droid4 where some devices would not connect
at all because of internal pull being used with an external pull
- Fix occasional missed wake-up events on droid4 modem uart
* tag 'omap-for-v5.6/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix occasional lost wakeirq for uart1
ARM: dts: omap4-droid4: Fix flakey wlan by disabling internal pull for gpio
ARM: dts: dra7: Fix bus_dma_limit for PCIe
ARM: dts: am574x-idk: Disable m_can node
Link: https://lore.kernel.org/r/pull-1588872844-804667@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
make dtc and the new dtscheck against yaml bindings happy.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl6yA9QQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeX0CACEwXPa8ChfXg+N4846D/wcwkpMVQqnTbMR
WrnqVLUNHf71h7Yej/aXpBSgEq5er1Q/HVgbjvkAAYNw633MNWgaNMi9AFl03gTF
uSOSUoiwauUUlvWt2aZ44IHxHS/WC0FB9/wIROpnD0SJvmYX9MJF8AVITNDsTDGv
EsSswwAXiBxILDWWdBM2QgAZxEhan3MwBbHQrmPRePDAWylluT3tMGjEfLgIapcW
9w44tw0kR8g7Zwgq+MYcfyHoNhUXOr1iMlCCA0LWOOtNBJAbXKM4XDp4cWwHLiI3
nktZSWXN7B08dx4hi/++18izC6N/ZwoGycMN4wG9kvdaRnpwh3KN
=vkl2
-----END PGP SIGNATURE-----
Merge tag 'v5.7-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Some fixes for the newly added Pinebook Pro and other fixes to
make dtc and the new dtscheck against yaml bindings happy.
* tag 'v5.7-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix pinctrl sub nodename for spi in rk322x.dtsi
arm64: dts: rockchip: Fix Pinebook Pro FUSB302 interrupt
ARM: dts: rockchip: swap clock-names of gpu nodes
arm64: dts: rockchip: swap interrupts interrupt-names rk3399 gpu node
arm64: dts: rockchip: fix status for &gmac2phy in rk3328-evb.dts
arm64: dts: rockchip: remove extra assigned-clocks property from &gmac2phy node in rk3328-evb.dts
ARM: dts: rockchip: fix phy nodename for rk3229-xms6
ARM: dts: rockchip: fix phy nodename for rk3228-evb
arm64: dts: rockchip: Rename dwc3 device nodes on rk3399 to make dtc happy
arm64: dts: rockchip: drop #address-cells, #size-cells from rk3399 pmugrf node
arm64: dts: rockchip: drop #address-cells, #size-cells from rk3328 grf node
arm64: dts: rockchip: drop non-existent gmac2phy pinmux options from rk3328
arm64: dts: rockchip: Replace RK805 PMIC node name with "pmic" on rk3328 boards
arm64: dts: rockchip: enable DC charger detection pullup on Pinebook Pro
arm64: dts: rockchip: fix inverted headphone detection on Pinebook Pro
arm64: dts: rockchip: Correct PMU compatibles for PX30 and RK3308
Link: https://lore.kernel.org/r/1738941.6LdaBJIBqS@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix IOMMU support on R-Car V3H,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXqqEEQAKCRCKwlD9ZEnx
cK6VAQDEYT5s4bzgLANPkTuvz3n5NgmS1nSC9tGrUX9co4OEUgD+OkwEnFJgLF1+
LbwisW1fNfCz1looPeyyZTl9Q8o5Yg0=
=cIRT
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.7
- Fix IOMMU support on R-Car V3H,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
* tag 'renesas-fixes-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: r7s9210: Remove bogus clock-names from OSTM nodes
arm64: dts: renesas: r8a77980: Fix IPMMU VIP[01] nodes
ARM: dts: r8a73a4: Add missing CMT1 interrupts
Link: https://lore.kernel.org/r/20200430084834.1384-1-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Set correct AHB clock for i.MX8MN SDMA1 device to fix a "Timeout
waiting for CH0" error.
- Fix a linker error for i.MX6 configurations that have ARM_CPU_SUSPEND=n,
which can happen if neither CONFIG_PM, CONFIG_CPU_IDLE, nor ARM_PSCI_FW
are selected.
- Fix I2C1 pinctrl configuration for i.MX27 phytec-phycard board.
- Fix i.MX8M AIPS 'reg' properties to remove DTC simple_bus_reg
warnings.
- Add missing compatible "fsl,vf610-edma" for LS1028A EDMA device, so
that bootloader can fix up the IOMMU entries there. Otherwise, EDMA
just doesn't work on LS1028A with shipped bootloader.
- Fix imx6dl-yapp4-ursa board Ethernet connection.
- Fix input_val for AUDIOMIX_BIT_STREAM pinctrl defines on i.MX8MP
according to Reference Manual.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl6pHtIUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM69sAgAp/H4BASI7SAbrjYsFjCP+ymPVgeS
Y9oeLm09Q2XEF6GiRhK4SDqN56BOUelRI6nqWx3k6sU5A7SuZMqGSaZZEhCtHhjl
iixyxSccxh4prUWSEDQPHyIJ6yjBt+QkKhycOVLwq7FFLdlrSaRuameNQAkjEU4a
YPSL0oBd1xNbz75RaqgmyI0lzOuQg1P+GMQqmVOYfrucK94bq62FMSezyEBQxKU+
0MVG/hEkeLtxFgzE6OpkBs1p1m+KgXE7qvV0W84VyZOKgri1qJ74V1Pl/RJNNVA0
p46c3PH66OATAU7+pbshC0x/hsN8ZVAoBhPit5oLF7ugDNpi377jT/zRrw==
=z3sI
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.7:
- Set correct AHB clock for i.MX8MN SDMA1 device to fix a "Timeout
waiting for CH0" error.
- Fix a linker error for i.MX6 configurations that have ARM_CPU_SUSPEND=n,
which can happen if neither CONFIG_PM, CONFIG_CPU_IDLE, nor ARM_PSCI_FW
are selected.
- Fix I2C1 pinctrl configuration for i.MX27 phytec-phycard board.
- Fix i.MX8M AIPS 'reg' properties to remove DTC simple_bus_reg
warnings.
- Add missing compatible "fsl,vf610-edma" for LS1028A EDMA device, so
that bootloader can fix up the IOMMU entries there. Otherwise, EDMA
just doesn't work on LS1028A with shipped bootloader.
- Fix imx6dl-yapp4-ursa board Ethernet connection.
- Fix input_val for AUDIOMIX_BIT_STREAM pinctrl defines on i.MX8MP
according to Reference Manual.
* tag 'imx-fixes-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: freescale: imx8mp: update input_val for AUDIOMIX_BIT_STREAM
arm64: dts: imx8m: Fix AIPS reg properties
arm64: dts: imx8mn: Change SDMA1 ahb clock for imx8mn
ARM: dts: imx27-phytec-phycard-s-rdk: Fix the I2C1 pinctrl entries
ARM: imx: provide v7_cpu_resume() only on ARM_CPU_SUSPEND=y
ARM: dts: imx6dl-yapp4: Fix Ursa board Ethernet connection
arm64: dts: ls1028a: add "fsl,vf610-edma" compatible
dt-bindings: dma: fsl-edma: fix ls1028a-edma compatible
Link: https://lore.kernel.org/r/20200429063226.GT32592@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Recent PTP-specific cpsw driver changes started exposing an issue on at
at least j5eco-evm:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xf0169004
...
(davinci_mdio_runtime_suspend) from [<c063f2a4>] (__rpm_callback+0x84/0x154)
(__rpm_callback) from [<c063f394>] (rpm_callback+0x20/0x80)
(rpm_callback) from [<c063f4f0>] (rpm_suspend+0xfc/0x6ac)
(rpm_suspend) from [<c0640af0>] (pm_runtime_work+0x88/0xa4)
(pm_runtime_work) from [<c0155338>] (process_one_work+0x228/0x568)
...
Let's fix the issue by using the correct mdio clock as suggested by
Grygorii Strashko <grygorii.strashko@ti.com>.
The DM814_ETHERNET_CPGMAC0_CLKCTRL clock is the interconnect target module
clock and managed by ti-sysc.
Fixes: 6398f3478e ("ARM: dts: Configure interconnect target module for dm814x cpsw")
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Clock Pulse Generator (CPG) device node lacks the extal2 clock.
This may lead to a failure registering the "r" clock, or to a wrong
parent for the "usb24s" clock, depending on MD_CK2 pin configuration and
boot loader CPG_USBCKCR register configuration.
This went unnoticed, as this does not affect the single upstream board
configuration, which relies on the first clock input only.
Fixes: d9ffd583bf ("ARM: shmobile: r8a7740: add SoC clocks to DTS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200508095918.6061-1-geert+renesas@glider.be
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on boards:
am437x-gp-evm
am437x-sk-evm
am437x-idk-evm
All above boards have phy-mode = "rgmii" and this is worked before, because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on boards:
am571x-idk
am572x-idk
am574x-idk
am57xx-beagle-x15
All above boards have phy-mode = "rgmii" and this is worked before because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clocksource to timer configured in pwm mode can be selected using the DT
property ti,clock-source. There are few pwm timers which are not
selecting the clock source and relying on default value in hardware or
selected by driver. Instead of relying on default value, always select
the clock source from DT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like using the UART CTS pin does not always trigger for a wake-up
when the SoC is idle.
This is probably because the modem first uses gpio_149 to signal the SoC
that data will be sent, and the CTS will only get used later when the
data transfer is starting.
Let's fix the issue by configuring the gpio_149 pad as the wakeirq for
UART. We have gpio_149 managed by the USB PHY for powering up the right
USB mode, and after that, the gpio gets recycled as the modem wake-up
pin. If needeed, the USB PHY can also later on be configured to use
gpio_149 pad as the wakeirq as a shared irq.
Let's also configure the missing properties for uart-has-rtscts and
current-speed for the modem port while at it. We already configure the
hardware flow control pins with uart1_pins pinctrl setting.
Cc: maemo-leste@lists.dyne.org
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wlan on droid4 is flakey on some devices, and experiments have shown this
gets fixed if we disable the internal pull for wlan gpio interrupt line.
The symptoms are that the wlan connection is very slow and almost useless
with lots of wlcore firmware reboot warnings in the dmesg.
In addition to configuring the wlan gpio pulls, let's also configure the rest
of the wlan sd pins. We have not configured those eariler as we're booting
using kexec.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the necessary MDIO interface node
to the Qualcomm IPQ4019 DTSI.
Built-in QCA8337N switch is managed using it,
and since we have a driver for it lets add it.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size field of the tag header structure is supposed to be set to the
size of a tag structure including the header.
Fixes: c772568788 ("ARM: add additional table to compressed kernel")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Copying source files during the build time may not end up with
as clean code as expected.
lib/fdt*.c simply wrap scripts/dtc/libfdt/fdt*.c, and it works
nicely. Let's follow this approach for the arm decompressor, too.
Add four wrappers, arch/arm/boot/compressed/fdt*.c and remove
the Makefile messes. Another nice thing is we no longer need to
maintain the own libfdt_env.h because the decompressor can include
<linux/libfdt_env.h>.
There is a subtle problem when generated files are turned into
check-in files.
When you are doing a rebuild of an existing object tree with O=
option, there exists stale "shipped" copies that the old Makefile
implementation created. The build system ends up with compiling the
stale generated files because Make searches for prerequisites in the
current directory, i.e. $(objtree) first, and then the directory
listed in VPATH, i.e. $(srctree).
To mend this issue, I added the following code:
ifdef building_out_of_srctree
$(shell rm -f $(addprefix $(obj)/, fdt_rw.c fdt_ro.c fdt_wip.c fdt.c))
endif
This will need to stay for a while because "git bisect" crossing this
commit, otherwise, would result in a build error.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Usually it does not hurt to add "clock-names" properties, even if the
(pre-json-schema) DT bindings do not mention them.
However, the actual clock names for the OS Timer nodes are not fixed,
but contain the indices of the consumer instances. Hence they cannot
easily be used by a driver, without scanning for all possible indices.
Remove them, as the OSTM DT bindings do not specify clock-names anyway.
Fixes: bbbcd02b82 ("ARM: dts: r7s9210: Initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Chris Brandt <Chris.Brandt@renesas.com>
Link: https://lore.kernel.org/r/20200427192932.28967-1-geert+renesas@glider.be
A test with the command below gives these errors:
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-1:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-1:
'#address-cells' is a required property
The $nodename pattern for spi nodes is
"^spi(@.*|-[0-9a-f])*$". To prevent warnings rename
'spi-0' and 'spi-1' pinctrl sub nodenames to
'spi0' and 'spi1' in 'rk322x.dtsi'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200424123923.8192-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Dts files with Rockchip 'gpu' nodes were manually verified.
In order to automate this process arm,mali-utgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-utgard.yaml expects clock-names values
in the same order, so fix that.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425192500.1808-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3229-xms6.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-2-jbx6244@gmail.com
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3228-evb.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-1-jbx6244@gmail.com
Linus Torvalds