Commit Graph

2830 Commits

Author SHA1 Message Date
John W. Linville c6b6eedc29 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 2012-08-23 09:51:15 -04:00
Thomas Pedersen 27f011243a mac80211: fix DS to MBSS address translation
The destination address of unicast frames forwarded through a mesh gate
was being replaced with the broadcast address. Instead leave the
original destination address as the mesh DA. If the nexthop address is
not in the mpath table it will be resolved. If that fails, the frame
will be forwarded to known mesh gates.

Reported-by: Cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-08-22 09:45:05 +02:00
John W. Linville 1a26904eb6 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 2012-08-02 13:49:38 -04:00
Johannes Berg dd4c9260e7 mac80211: cancel mesh path timer
The mesh path timer needs to be canceled when
leaving the mesh as otherwise it could fire
after the interface has been removed already.

Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-08-01 21:03:21 +02:00
Johannes Berg 2d9957cce6 mac80211: clear timer bits when disconnecting
There's a corner case that can happen when we
suspend with a timer running, then resume and
disconnect. If we connect again, suspend and
resume we might start timers that shouldn't be
running. Reset the timer flags to avoid this.

This affects both mesh and managed modes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-08-01 20:58:28 +02:00
Eliad Peller ba846a502c mac80211: don't clear sched_scan_sdata on sched scan stop request
ieee80211_request_sched_scan_stop() cleared
local->sched_scan_sdata. However, sched_scan_sdata
should be cleared only after the driver calls
ieee80211_sched_scan_stopped() (like with normal hw scan).

Clearing sched_scan_sdata too early caused
ieee80211_sched_scan_stopped_work to exit prematurely
without properly cleaning all the sched scan resources
and without calling cfg80211_sched_scan_stopped (so
userspace wasn't notified about sched scan completion).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-30 09:14:36 +02:00
Johannes Berg fcb06702f0 Merge remote-tracking branch 'wireless/master' into mac80211 2012-07-30 09:13:03 +02:00
Linus Torvalds aa0b3b2bee Merge branch 'for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED subsystem update from Bryan Wu.

* 'for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (50 commits)
  leds-lp8788: forgotten unlock at lp8788_led_work
  LEDS: propagate error codes in blinkm_detect()
  LEDS: memory leak in blinkm_led_common_set()
  leds: add new lp8788 led driver
  LEDS: add BlinkM RGB LED driver, documentation and update MAINTAINERS
  leds: max8997: Simplify max8997_led_set_mode implementation
  leds/leds-s3c24xx: use devm_gpio_request
  leds: convert Network Space v2 LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert DAC124S085 LED driver to devm_kzalloc()
  leds: convert LM3530 LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert TCA6507 LED driver to devm_kzalloc()
  leds: convert Freescale MC13783 LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert ADP5520 LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert PCA955x LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert Sun Fire LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert PCA9532 LED driver to devm_kzalloc()
  leds: convert LT3593 LED driver to devm_kzalloc()
  leds: convert Renesas TPU LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert LP5523 LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert PCA9633 LED driver to devm_kzalloc()
  ...
2012-07-26 20:26:27 -07:00
Johannes Berg 3aa569c3fe mac80211: fix scan_sdata assignment
We need to use RCU to assign scan_sdata.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-24 16:54:11 +02:00
Shuah Khan 19cd67e2d5 leds: Rename led_brightness_set() to led_set_brightness()
Rename leds external interface led_brightness_set() to led_set_brightness().
This is the second phase of the change to reduce confusion between the
leds internal and external interfaces that set brightness. With this change,
now the external interface is led_set_brightness(). The first phase renamed
the internal interface led_set_brightness() to __led_set_brightness().
There are no changes to the interface implementations.

Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
2012-07-24 07:52:34 +08:00
John W. Linville 90b90f60c4 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2012-07-20 12:30:48 -04:00
John W. Linville 3e497e0215 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next 2012-07-19 12:35:00 -04:00
Eliad Peller 99102bd380 mac80211: flush stations before stop beaconing
When AP interface is going down, the stations
are flushed (in ieee80211_do_stop()) only after
the beaconing was stopped.

However, drivers might rely on stations being
removed before the beaconing was stopped, in
order to clean up properly.

Fix it by flushing the stations on ap stop.

(we already do the same for other interface
types, e.g. in ieee80211_set_disassoc())

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-18 17:03:51 +02:00
John W. Linville d369f7b2b2 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2012-07-17 15:31:33 -04:00
John W. Linville 707be0ae13 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next 2012-07-17 15:07:31 -04:00
Eliad Peller 88bc40e8c3 mac80211: go out of PS before sending disassoc
on disassoc, ieee80211_set_disassoc() goes out of PS
before indicating BSS_CHANGED_ASSOC (not sure why this
is needed, but some drivers might count on the current
behavior).

However, it does it after sending the disassoc
frame, which results in null-data frame being sent
(in order to go out of ps) after we were already sent
the disassoc, which is invalid.

Fix it by going out of ps before sending the disassoc.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-17 12:17:42 +02:00
Nicolas Cavallari 7f9f78ab96 mac80211: fix tx-mgmt cookie value being left uninitialized
commit "mac80211: unify SW/offload remain-on-channel"
moved the cookie assignment from ieee80211_mgmt_tx()
to ieee80211_start_roc_work().  But the latter is only
called where offchannel is needed.  If offchannel isn't
needed/used, a uninitialized cookie value would be returned
to userspace.

This patch sets the cookie value when offchannel isn't used.

Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-17 11:22:42 +02:00
Johannes Berg 5b7ccaf3fc cfg80211/mac80211: re-add get_channel operation
This essentially reverts commit 2e165b8184 but
introduces the get_channel operation with a new
wireless_dev argument so that you can retrieve
the channel per interface. This is necessary as
even though we can track all interface channels
(except monitor) we can't track the channel type
used.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-13 16:16:11 +02:00
Johannes Berg 075e08477d Revert "mac80211: refactor virtual monitor code"
This reverts commit 870d37fc22.

This code doesn't work as cfg80211 will call
set_monitor_enabled at the wrong time and it
doesn't seem to be possible to fix this.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-13 16:16:10 +02:00
Alan Cox 4b4b8229ae mac80211: fix use after free
roc is destroyed then roc->started is referenced. Keep a local cache.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-13 16:15:54 +02:00
John W. Linville d07d152892 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
	drivers/net/wireless/iwmc3200wifi/cfg80211.c
	drivers/net/wireless/mwifiex/cfg80211.c
2012-07-12 15:21:05 -04:00
John W. Linville 38a0084063 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2012-07-12 13:44:50 -04:00
Johannes Berg 685fb72b63 mac80211: iterate the virtual monitor interface
If the virtual monitor interface is requested
by the driver, it should also be iterated over
when the driver wants to iterate all active
interfaces.

To allow that protect it with the iflist_mtx.

Change-Id: I58ac5de2f4ce93d12c5a98ecd2859f60158d5d69
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:50 +02:00
Sylvain Roger Rieunier 2a9e6c5887 minstrel_ht: enable frame aggregation for fixed rate
When sample_idx is set to a value other than -1 it activates
the IEEE80211_TX_CTL_RATE_CTRL_PROBE flag which disables
frame aggregation. To allow frame aggregation during fixed
rate it is necessary to set max_tp_rate, max_tp_rate2 and
max_prob_rate instead of sample_idx.

Signed-off-by: Sylvain Roger Rieunier <sylvain.roger.rieunier@gmail.com>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:48 +02:00
Nicolas Cavallari 4922f71f25 mac80211: tx: do not drop non-robust mgmt to non-MFP stas.
When drop_unencrypted is enabled and MFP is disabled,
non-robust management frames for not-yet associated STA are dropped.
This isn't visible as many management frames sent from the kernel
have TX_INTFL_DONT_ENCRYPT set and management frames injected
from a monitor vif have TX_CTL_INJECTED so aren't dropped.
But management frames sent from userspace via NL80211_CMD_FRAME
do not have this flag set, so are dropped.

This patch make it always accept non-robust management frames.

Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:48 +02:00
Johannes Berg 46e6de159d mac80211: restructure key selection
The "no key" case in key selection that decides
whether to drop the frame or not is impossible
to understand, restructure the code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[cavallar@lri.fr: removed blank line and restructured action frame clause]
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
2012-07-12 12:10:47 +02:00
Johannes Berg 8c358bcd09 mac80211: add time synchronisation with BSS for assoc
Some drivers (iwlegacy, iwlwifi and rt2x00) today use the
bss_conf.last_tsf value. By itself though that value is
completely worthless since it may be ancient. What really
is needed is synchronisation between some device time and
the TSF.

To clarify this, rename bss_conf.last_tsf to sync_tsf and
add sync_device_ts which is obtained from rx_status which
gets a new field device_timestamp for this purpose. This
is intentionally not using the mactime field since that
is used for other things and in IBSS is expected to sync
with the IBSS's TSF which isn't necessarily true for the
device timestamp.

Also, since we have the information and it's useful even
before the connection has been established, give all the
timing details to the driver before authenticating.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:46 +02:00
Johannes Berg d48b296850 mac80211: redesign scan RX
Scan receive is rather inefficient when there are
multiple virtual interfaces. We iterate all of the
virtual interfaces and then notify cfg80211 about
each beacon many times.

Redesign scan RX to happen before everything else.
Then we can also get rid of IEEE80211_RX_IN_SCAN
since we don't have to accept frames into the RX
handlers for scanning or scheduled scanning any
more. Overall, this simplifies the code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:44 +02:00
Johannes Berg 5260a5b2c3 mac80211: track scheduled scan virtual interface
Instead of tracking whether or not we're in a
scheduled scan, track the virtual interface
(sdata) in an RCU-protected pointer to make it
usable from RX to check the MAC address.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:43 +02:00
Johannes Berg e2fd5dbc1c mac80211: make scan_sdata pointer usable with RCU
Making the scan_sdata pointer usable with RCU makes
it possible to dereference it in the RX path to see
if a received frame actually matches the interface
that is scanning. This is just preparations, making
the pointer __rcu.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:43 +02:00
Arik Nemtsov d811b3d556 mac80211: fix invalid band deref building preq IEs
The function building probe-request IEs does not validate the band is
supported before dereferencing it. This can result in a panic when
all bands are traversed, as done during sched-scan start.

Warn when this happens and return an empty probe request. Also fix
sched-scan to not waste memory on unsupported bands.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:42 +02:00
Johannes Berg fd0142844e nl80211: move scan API to wdev
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:41 +02:00
Johannes Berg 84efbb84cf cfg80211: use wireless_dev for interface management
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:08:10 +02:00
Chun-Yeow Yeoh 7c41f3159c mac80211: Fix the Problem of Unreachable Mesh STA from DS
This patch fixes the problem of unreachable mesh STA from
Distribution System (DS) due to the introduction of previous
patch solving the mesh STA joining from one MBSS to another
MBSS.

Reported-by: Georgiewskiy Yuriy <bottleman@icf.org.ru>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-11 16:24:54 -04:00
David S. Miller 04c9f416e3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	net/batman-adv/bridge_loop_avoidance.c
	net/batman-adv/bridge_loop_avoidance.h
	net/batman-adv/soft-interface.c
	net/mac80211/mlme.c

With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).

The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-10 23:56:33 -07:00
Ben Hutchings 2c53040f01 net: Fix (nearly-)kernel-doc comments for various functions
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-10 23:13:45 -07:00
Christian Lamparter 353d09c6ce mac80211: fix read outside array bounds
ieee802_1d_to_ac is defined as a const int[8],
but the tid parameter has a range from 0 to 15.

Cc: stable@vger.kernel.org
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10 11:42:52 -04:00
John W. Linville 0af5491c2f Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next 2012-07-09 16:34:39 -04:00
John W. Linville 635d999fd3 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	net/mac80211/mlme.c
2012-07-09 16:34:34 -04:00
Eliad Peller 10a9109f27 mac80211: destroy assoc_data correctly if assoc fails
If association failed due to internal error (e.g. no
supported rates IE), we call ieee80211_destroy_assoc_data()
with assoc=true, while we actually reject the association.

This results in the BSSID not being zeroed out.

After passing assoc=false, we no longer have to call
sta_info_destroy_addr() explicitly. While on it, move
the "associated" message after the assoc_success check.

Cc: stable@vger.kernel.org [3.4+]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 15:01:00 -04:00
Thomas Huehn 472dd35ccb mac80211: correct size the argument to kzalloc in minstrel_ht
msp has type struct minstrel_ht_sta_priv not struct minstrel_ht_sta.

(This incorporates the fixup originally posted as "mac80211: fix kzalloc
memory corruption introduced in minstrel_ht". -- JWL)

Reported-by: Fengguang Wu <wfg@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 14:59:58 -04:00
Johannes Berg 71bbc99438 cfg80211: use wdev in mgmt-tx/ROC APIs
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-09 14:51:47 +02:00
Johannes Berg f72b85b8eb mac80211: remove ieee80211_key_removed
This API call was intended to be used by drivers
if they want to optimize key handling by removing
one key when another is added. Remove it since no
driver is using it. If needed, it can always be
added back.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-09 14:49:15 +02:00
Johannes Berg 31ee67a1ce mac80211: remove unused assignment
ieee80211_mlme_notify_scan_completed() iterates all
interfaces and doesn't need to assign anything to
the sdata variable before the loop.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-09 14:49:11 +02:00
Johannes Berg 7d25745d05 mac80211: update BSS info on AC parameters change
When the AC parameters change, drivers might rely
on getting a bss_info_changed notification with
BSS_CHANGED_QOS in addition to the conf_tx call.

Always call the function when userspace updates
are made (in AP/GO modes) and also set the change
flag when updates were made by the AP (in managed
mode.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-09 14:49:00 +02:00
Christian Lamparter 2f7916f8d6 mac80211: request TX status for BlockAck Requests
Because ieee80211_tx_status in status.c checks if
outgoing BlockAck requests have been acked, it is
necessary to tell the driver that tx feedback for
this sort of frame is important.

Otherwise, the stack will continue to send the same
BlockAck request over and over, which can cause
the receiver to flush or clean its reorder buffer
over and over.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-07 21:35:42 +02:00
Johannes Berg a6f38ac3cc mac80211: fix crash with single-queue drivers
Larry (and some others I think) reported that with
single-queue drivers mac80211 crashes when waking
the queues. This happens because we allocate just
a single queue for each virtual interface in case
the driver doesn't have at least 4 queues, but the
code stopping/waking the virtual interface queues
wasn't taking this into account.

Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-06 15:26:58 +02:00
Eliad Peller c62094889f mac80211: always set in_reconfig=false on wakeup
If the interfaces were removed just before a restart
work was started, open_count will be 0, and most of
the reconfig work will be skipped, including the
resetting of local->in_reconfig to false.

Leaving local->inconfig = true will result in
dropping any incoming packet.

Fix it by always setting local->in_reconfig = false
(even if there are no active interfaces).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-06 08:33:05 +02:00
Johannes Berg 135792ec24 mac80211: fix debugfs default key links
Due to the way the default key links are created,
it happens that a link is left dangling:
 * both unicast/multicast links are created
 * unicast link is destroyed, and the links
   are updated
 * during this update, adding the multicast
   link again fails because it is present,
   destroying the debugfs pointer
 * removing the multicast link won't work as
   the pointer has been destroyed

Fix this by always removing the links and then
re-creating them if needed.

Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Reported-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-06 08:33:04 +02:00
Johannes Berg a1845fc7c5 mac80211: add TX prepare API
Some drivers require setup before being able to send
management frames in managed mode, in particular in
multi-channel cases.

Introduce API to allow the drivers to do such setup
while being able to sleep waiting for the setup to
finish in the device. This isn't possible inside the
TX call since that can't sleep.

A future patch may also restructure the TX retry to
wait for the driver to report the frame status, as
suggested by Arik in
http://mid.gmane.org/CA+XVXffKSEL6ZQPQ98x-zO-NL2=TNF1uN==mprRyUmAaRn254g@mail.gmail.com

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-03 13:50:34 +02:00