Annotate UARTs and move the serial UART "nvidia,tegra30-hsuart"
compatible definitions from the carrier board to the module level device
trees. One could still override this in a custom carrier board device
tree if required.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Annotate PCIe port nodes and clean-up PCIe controller/port status' with
respect to carrier board vs. module level device trees. As port 3
connects to the on-module Gigabit Ethernet MACPHY it is always enabled
together with the PCIe controller itself.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to avoid any floating SD card detect pins as may e.g. happen on
Ixora V1.1A pull them all up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is similar to tegra124 and avoids the following being reported
upon boot:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There was a dot instead of a comma. Fix this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the actual dts for the tinker board S, which brings its own emmc
device, not therefore not requiring an sd-card to boot.
Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tinker Board and Tinker Board S share most of their components,
so should also not replicate these for each variant.
So move them to a shared dtsi that then can get included by both
boards.
Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On the imx6qdl-zii-rdu2 board the RTC functionality is provided via
a DS1341 RTC connected via I2C bus, so we can safely disable the internal
one.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/rtc/rtc-ds1307.txt the
original compatible "maxim,ds1341" is not a valid entry.
Switch to the documented "dallas,ds1341" compatible.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6UL, accessing OCOTP directly is wrong because the ocotp clock
needs to be enabled first, so use the nvmem-cells binding instead.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtc has new checks for SPI buses. Fix the warnings in node names and
unit-addresses.
There's over 100 warnings for FSL boards, a few examples:
arch/arm/boot/dts/imx28-duckbill-2-spi.dtb: Warning (spi_bus_bridge): /apb@80000000/apbh@80000000/ssp@80014000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx53-ppd.dtb: Warning (spi_bus_bridge): /soc/aips@50000000/spba@50000000/ecspi@50010000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (spi_bus_reg): /soc/aips-bus@2000000/spba-bus@2000000/spi@2014000/mcp251x@1: SPI bus unit address format error, expected "0"
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To use the "earlycon" kernel command line parameter (without arguments)
we need a stdout-path property under the /chosen node. Add this to make
it easier to spot errors early in the boot process when looking for
them.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Odroid-C1 exposes ADC channels 0 and 1 on the GPIO headers. NOTE: Due
to the SoC design these are limited to 1.8V (instead of 3.3V like all
other pins).
Enable the SAR ADC to enable voltage measurements on these pins.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There are multiple fixed regulators on the Odroid-C1 board. Add them so
they can be used when we add the devices that need them (SAR ADC needs
the 1.8V IOREF, RTC needs VDD_RTC).
These are:
- P5V0 is the main 5V power input
- VCC3V3 / VDDIO_AO3V3 / VDD3V3: fixed regulator with 3.3V output which
is supplied by P5V0
- IOREF_1V8 / VCC1V8 / VDD1V8: fixed regulator with 1.8V output which is
supplied by P5V0
- VDD_RTC: fixed voltage regulator with 0.9V output which is supplied by
VDDIO_AO3V3
- DDR_VDDC / DDR3_1V5: fixed voltage regulator with 1.5V output which is
supplied by P5V0
- the existing TF_IO and RFLASH_VDD_EN regulators are supplied by
VDDIO_AO3V3
- the existing VCCK regulator is supplied by P5V0
This does not add the missing VDDEE regulator (controlled by PWM_D)
because it's not clear yet how to configure the voltage of that
regulator.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The CPU voltage regulator is a "Monolithic Power Systems MP2161"
(according to the Odroid-C1+'s schematics). It is driven by PWM_C on
GPIODV_9.
Hardkernel's 3.10 kernel (based on the Amlogic GPL kernel sources)
defines a PWM voltage table with the following values:
- 0.86 volts = PWM register value 0x10f001b
- (more values in 0.1 volt increments)
- 1.14 volts = PWM register value 0x000012a
When using the XTAL (24MHz) as input this translates into a PWM period
of 12218ns with 0.86V using a duty cycle of 91% and 1.14V using a duty
cycle of 0%.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Endless Mini (EC-100) is a grapefruit-sized computer based on the
Amlogic Meson8b (S805) SoC which comes in two variants.
Both variants have in common:
- Amlogic Meson8b (S805) SoC
- two USB 2.0 ports on the rear, one one the front (connected to the SoC
through an internal hub)
- 3.5mm Stereo out and MIC combo port
- HDMI and CVBS output
- 5V power supply (rated at 3A / 15W)
- an internal embedded micro-controller (called "EC") which implements a
"breathing" effect for the LED and allows shutting down (powering off)
the whole device
- 10/100 Mbit/s Ethernet using an IC Plus IP101A/G PHY (note: the website
incorrectly lists a Gigabit Ethernet port)
- the CPU voltage is regulated using a PWM regulator. The GPL sources of
the EC-100 are using a PWM value of 0x1c0000 for 0.86V and a PWM value
of 0x00001c for 1.14V. When using the XTAL (24MHz) as input this
translates into a PWM period of 1148ns with 0.86V using a duty cycle of
100% and 1.14V using a duty cycle of 0%.
The main differences are:
- the main indicator for the variant is the RAM size: the "cheaper"
variant has 1 GB of RAM, while the more expensive one comes with 2GB
- the storage size differs: 24 GB vs 32 GB
- the "1 GB RAM" variant has Ethernet connectivity only, while the "2 GB"
variant has a Realtek RTL8723BS SDIO chip which adds 802.11b/g/n wifi
and Bluetooth 4.0 support
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Some boards use an RMII Ethernet PHY which requires fewer pins than the
RGMII PHYs. Add a separate eth_rmii_pins node which does not include the
pins which are only required for RGMII (but not for RMII) PHYs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
These are used for example on the Endless Mini (EC-100):
- I2C_A is connected to the Realtek RT5640 audio codec
- PWM_C (GPIODV_9) is connected to a PWM regulator which is used for
VCCK (CPU voltage supply)
- UART_B is connected to the Bluetooth module (of the RTL8723BS SDIO
wifi and Bluetooth combo chip)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Remove unused parameter from SPI6 dmas property on stm32mp157c SoC.
Fixes: dc3f8c86c1 ("ARM: dts: stm32: add SPI support on stm32mp157c")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[olof: Without this patch, SPI6 will fall back to interrupt mode with
lower perfmance]
Signed-off-by: Olof Johansson <olof@lixom.net>
Pass the 'no-sd' for esdhc0 controller as it is wired to eMMC.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No SDIO devices are connected to these ports, so pass the 'no-sdio'
property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx51-zii-scu2-mezz has an external watchdog in the environment
microcontroller, so disable the internal one.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx51-zii-scu2-mezz does not have any video encoding/decoding needs,
so disable the VPU.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx51-zii-scu3-esb does not have any video encoding/decoding needs,
so disable the VPU.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
intended for 4.19, please pull the following:
- Florian fixes the PPI and SPI interrupts in the BCM63138 (DSL) SoC DTS
-----BEGIN PGP SIGNATURE-----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=FoxN
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.19/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree changes
intended for 4.19, please pull the following:
- Florian fixes the PPI and SPI interrupts in the BCM63138 (DSL) SoC DTS
* tag 'arm-soc/for-4.19/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM63xx: Fix incorrect interrupt specifiers
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Bring up DSI and HDMI on Exynos5250 Arndale.
2. Use the new way of setting external wakeup interrupts on S5Pv210.
3. Use proper cpufreq suspend OPP to fix suspend/wakeup from RAM on Snow
Chromebook (Exynos5250).
4. Fully describe regualtors on Odroid XU3-family boards.
5. Fix sound in Snow-rev5 Chromebook.
6. Fix regulators configuration on Peach Pi/Pit Chromebooks (Exynos5420)
which should be always on.
7. Fix pull control on PMIC interrupt lines on multiple boards which
essentially fixes waking up by RTC.
8. Add PMIC interrupts on Exynos4210 UniversalC210 board.
9. Add external SD card support for Trats board (Exynos4210).
10. Correct audio subsystem parent clock on Peach Chromebooks.
11. Minor cleanups.
-----BEGIN PGP SIGNATURE-----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=WT7h
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.20-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.20
1. Bring up DSI and HDMI on Exynos5250 Arndale.
2. Use the new way of setting external wakeup interrupts on S5Pv210.
3. Use proper cpufreq suspend OPP to fix suspend/wakeup from RAM on Snow
Chromebook (Exynos5250).
4. Fully describe regualtors on Odroid XU3-family boards.
5. Fix sound in Snow-rev5 Chromebook.
6. Fix regulators configuration on Peach Pi/Pit Chromebooks (Exynos5420)
which should be always on.
7. Fix pull control on PMIC interrupt lines on multiple boards which
essentially fixes waking up by RTC.
8. Add PMIC interrupts on Exynos4210 UniversalC210 board.
9. Add external SD card support for Trats board (Exynos4210).
10. Correct audio subsystem parent clock on Peach Chromebooks.
11. Minor cleanups.
* tag 'samsung-dt-4.20-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Correct audio subsystem parent clock on Peach Chromebooks
ARM: dts: exynos: Add external SD card support for Trats board
ARM: dts: exynos: Disable pull control for PMIC IRQ line on Artik5 board
ARM: dts: exynos: Disable pull control for S5M8767 PMIC
ARM: dts: exynos: Remove double SD card detect pin inversion
ARM: dts: exynos: Add missing PMIC interrupts on UniversalC210 board
ARM: dts: exynos: Disable pull control for MAX8997 interrupts on Origen
ARM: dts: exynos: Fix regulators configuration on Peach Pi/Pit Chromebooks
ARM: dts: exynos: Fix sound in Snow-rev5 Chromebook
ARM: dts: exynos: Add LDO28 regulator on Exynos5422 Odroid boards
ARM: dts: exynos: Disable unused PMIC regulators on Exynos5422 Odroid boards
ARM: dts: exynos: Add unused PMIC regulators on Exynos5422 Odroid boards
ARM: dts: exynos: Add missing used PMIC regulators on Exynos5422 Odroid boards
ARM: dts: exynos: Mark 1 GHz CPU OPP as suspend OPP on Exynos5250
ARM: dts: exynos: Convert exynos5250.dtsi to opp-v2 bindings
ARM: dts: s5pv210: Switch to S5Pv210 specific pinctrl wakeup compatible
ARM: dts: exynos: Fix HDMI-HPD line handling on Arndale
ARM: dts: exynos: Use i2c-gpio for HDMI-DDC on Arndale
ARM: dts: exynos: Add DSI and panel nodes on Arndale
ARM: dts: exynos: Add DSI node on Exynos5250
Signed-off-by: Olof Johansson <olof@lixom.net>
_ Change syntax of multiple DAI links
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mMf1
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.20-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/dt
STi DT update:
_ Change syntax of multiple DAI links
* tag 'sti-dt-for-v4.20-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: stih410: change syntax of multiple DAI
Signed-off-by: Olof Johansson <olof@lixom.net>
- warning fiwes from Rob
- many updates for the axentia boards
- ADC, I2S and touch screen support for sama5d2
-----BEGIN PGP SIGNATURE-----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=jsRK
-----END PGP SIGNATURE-----
Merge tag 'at91-4.20-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into next/dt
AT91 DT for 4.20
- warning fiwes from Rob
- many updates for the axentia boards
- ADC, I2S and touch screen support for sama5d2
* tag 'at91-4.20-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
arm: dts: sama5d2: Update coresight bindings for hardware ports
ARM: dts: at91: sama5d27_som1_ek: add adc regulators
ARM: dts: atmel: Fix I2C and SPI bus warnings
ARM: dts: at91: sama5d4: add labels to soc dtsi for derivative boards
ARM: dts: at91: tse850: drop three indentation levels
ARM: dts: at91: nattis: drop three indentation levels
ARM: dts: at91: nattis: describe the lvds panel
ARM: dts: at91: nattis: move pinctrls for the lvds chip to the lvds node
ARM: dts: at91: nattis: state the actual lvds-encoder chip
ARM: dts: at91: nattis: make the SD-card slot work
ARM: dts: at91: nattis: set the PRLUD and HIPOW signals low
ARM: dts: at91/trivial: remove old NAND bindings leftover in sama5d2
ARM: dts: at91/trivial: Fix USART1 definition for at91sam9g45
ARM: dts: at91: sama5d2 Xplained: add pin muxing for I2S
ARM: dts: at91: sama5d2: add nodes for I2S controllers
ARM: dts: at91: sama5d2: add I2S clock muxing nodes
ARM: dts: at91: sama5d2: Add resistive touch device
ARM: dts: at91: sama5d2: add channel cells for ADC device
Signed-off-by: Olof Johansson <olof@lixom.net>
With change of syntax for 'simple-audio-card,dai-link' containers,
devicetrees of stih410 must be updated.
This fixes the following error:
[ 3.839466] asoc-simple-card sound: asoc_simple_card_dai_link_of:
Can't find simple-audio-card,cpu DT node
[ 3.849150] asoc-simple-card sound: parse error -22
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update VDD_SOC voltage to 1.25V for 900MHz operating point
according to datasheet Rev. 1.3, 08/2018, 25mV is added to
the minimum allowed values to cover power supply ripple.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pullup and down settings were missing, so add them to avoid
floating pins and make headset detection working.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The full AM3517-EVM shipped with an add-on board which contained
two Audio codecs, a GPIO expander with a variety of buttons, and
some other features. This patch enables these portions of the UI
board because they don't directly conflict with existing features.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the possibility to have more aggressive runtime pm
by providing proper wakeup irq for the serial console.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am574x-idk has no cpu vdd-supply at the moment. Hence hook smps12
regulator as cpu vdd-supply in am57xx-idk-common as the same regulator
feeds on to cpu on am571/2/4-idks. So remove all the individual
instances and place that in common place.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A number of our interrupts were incorrectly specified, fix both the PPI
and SPI interrupts to be correct.
Fixes: b5762cacc4 ("ARM: bcm63138: add NAND DT support")
Fixes: 46d4bca044 ("ARM: BCM63XX: add BCM63138 minimal Device Tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The proper parent clock for audio subsystem for Exynos5420 and Exynos5800
SoCs is CLK_MAU_EPLL. This fixes following warning:
clk: failed to reparent mout_audss to fout_epll: -22
Fixes: ed7d1307077e: ARM: dts: exynos: Enable HDMI audio support on Peach Pit
Fixes: bae0f445c1e7: ARM: dts: exynos: Enable HDMI audio support on Peach Pi
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
for 4.20, please pull the following:
- Rafal updates the Broadcom BCM5301x (Northstar) DTS files to use the
new style partition parser and removes the unsupported/undocumented
linux,part-probe properties that were previously introduced
- Stefan adds supports for the Raspberry Pi Compute Module 3/3Lite, he
also updates the Raspberry Pi 3B+ USB Ethernet adapter to have proper
LED configuration
- Rob fixes a bunch of SPI bus warnings in the Northstar Plus and
Hurricane 2 DTS files
- Florian documents the Broadcom roboswitch Switch Register Access Block
(SRAB) interrupts, adds the switch interrupts to the Northstar Plus
DTS include file and finally updates the BCM958625HR reference board to
have the proper SFP module definition
-----BEGIN PGP SIGNATURE-----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=OpXM
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.20/devicetree' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 4.20, please pull the following:
- Rafal updates the Broadcom BCM5301x (Northstar) DTS files to use the
new style partition parser and removes the unsupported/undocumented
linux,part-probe properties that were previously introduced
- Stefan adds supports for the Raspberry Pi Compute Module 3/3Lite, he
also updates the Raspberry Pi 3B+ USB Ethernet adapter to have proper
LED configuration
- Rob fixes a bunch of SPI bus warnings in the Northstar Plus and
Hurricane 2 DTS files
- Florian documents the Broadcom roboswitch Switch Register Access Block
(SRAB) interrupts, adds the switch interrupts to the Northstar Plus
DTS include file and finally updates the BCM958625HR reference board to
have the proper SFP module definition
* tag 'arm-soc/for-4.20/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Fix SPI bus warnings
ARM: dts: NSP: Wire up switch interrupts
dt-bindings: net: dsa: Document B53 SRAB interrupts and registers
ARM: dts: NSP: Enable SFP on bcm958625hr
ARM: dts: bcm283x-rpi-lan7515: Enable Ethernet LEDs
ARM: dts: BCM5301X: Specify flash partitions
ARM: dts: add Raspberry Pi Compute Module 3 and IO board
dt-bindings: bcm: Add Raspberry Pi CM3 and CM3L
Signed-off-by: Olof Johansson <olof@lixom.net>
One additional fix regarding HDMI on the R40 SoC.
Based on preliminary tests and code dumps for the R40, it was thought
that the whole HDMI block was the same on the R40 and A64.
Recent tests regarding the A64 showed that this was not the case. The
HDMI PHY on the A64 only has one clock parent. How this occurs at the
hardware level is unclear, as Allwinner has not given any feedback on
this matter. Nevertheless it is clear that the hardware acts differently
between the A64 and R40 in such a way that the R40's HDMI PHY is not
backward compatible with the A64's. As such we need to drop the fallback
compatible string in the R40's device tree. This was added in v4.19-rc1.
-----BEGIN PGP SIGNATURE-----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=eo72
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.19-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes - round 2
One additional fix regarding HDMI on the R40 SoC.
Based on preliminary tests and code dumps for the R40, it was thought
that the whole HDMI block was the same on the R40 and A64.
Recent tests regarding the A64 showed that this was not the case. The
HDMI PHY on the A64 only has one clock parent. How this occurs at the
hardware level is unclear, as Allwinner has not given any feedback on
this matter. Nevertheless it is clear that the hardware acts differently
between the A64 and R40 in such a way that the R40's HDMI PHY is not
backward compatible with the A64's. As such we need to drop the fallback
compatible string in the R40's device tree. This was added in v4.19-rc1.
* tag 'sunxi-fixes-for-4.19-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: drop A64 HDMI PHY fallback compatible from R40 DT
Signed-off-by: Olof Johansson <olof@lixom.net>
SPI controller nodes should be named 'spi' rather than 'qspi'. Fixing the
name enables dtc SPI bus checks.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The vmmc phandle, like all power supply property names, must have the
'-supply' suffix.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The compatible string "marvell,prestera" allows drivers to have code
common to any prestera variant.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/dove-cubox.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-dove-db.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@14600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/orion5x-kuroboxpro.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lschl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lsgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lswtgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
We need to distribute out the responsibilities of the PRCMU
registers instead of having one big lump handling everything.
By making it syscon compatible, we can start grabbing the
register map elsewhere when needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switch to the new coresight bindings
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switch to the new coresight bindings for hardware ports
Cc: linux-omap@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By removing the reference to skeleton.dtsi, defining chosen {}
and proper memory nodes we get warning-free device trees for
the Ux500.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The "lcdaclk_b_1" group is muxed with the function "lcd"
but needs a separate entry to be muxed in with "lcda"
rather than "lcd".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The unit address of the Cortex-A9 SCU device node contains one zero too
many. Remove it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/am437x-idk-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am437x-sk-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am43x-epos-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/omap3-n9.dtb: Warning (i2c_bus_reg): /ocp@68000000/i2c@48060000/ak8975@0f: I2C bus unit address format error, expected "f"
arch/arm/boot/dts/am335x-osd3358-sm-red.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/pressure@78: I2C bus unit address format error, expected "76"
arch/arm/boot/dts/am335x-boneblack.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am335x-boneblack-wireless.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am335x-sancloud-bbe.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am571x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am572x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am574x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am57xx-cl-som-am57x.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am57xx-sbc-am57x.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra72-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra72-evm-revc.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra76-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra7-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am335x-pdu001.dtb: Warning (spi_bus_reg): /ocp/spi@481a0000/cfaf240320a032t: SPI bus unit address format error, expected "0"
arch/arm/boot/dts/keystone-k2g-evm.dtb: Warning (spi_bus_bridge): /soc@0/qspi@2940000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/keystone-k2g-ice.dtb: Warning (spi_bus_bridge): /soc@0/qspi@2940000: node name for SPI buses should be 'spi'
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
[tony@atomide.com: fixed mode to 644 for am335x-osd3358-sm-red.dts while at it]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am335x-evm has only one CPSW external port physically wired, but DT defines
2 ext. ports. As result, PHY connection failure reported for the second
ext. port.
Update DT to reflect am335x-evm board HW configuration, and, while here,
switch to use phy-handle instead of phy_id.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This board is a plugin card for some of Marvell's switch development
kits. It's similar to the non-amc board except that it has no SATA
support.
[gregory: fix DTC warning and use the new partition binding]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Update the nand flash binding to the new style.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Update the nand flash binding to the new style.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Update the 98dx3236 SoC and dependent boards to use
"nand-controller" instead of "nand".
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Initial introduction of Facebook TiogaPass family equipped with
Aspeed 2500 BMC SoC. TiogaPass is a x86 server development kit
with a ASPEED ast2500 BMC manufactured by Facebook.
Specifically, This adds the TiogaPass platform device tree file
including the flash layout used by the TiogaPass BMC machines.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The HXT StarDragon 4800 REP2 (Reference Evaluation Platform) is
an aarch64 ARMv8 server platform with an ast2520 BMC.
Signed-off-by: Yuan Yao <yao.yuan@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
To fit with latest rtc driver updates, rtc st,syscfg property must contain
the control register offset of pwrcfg and the mask corresponding to the
DBP (Disable Backup Protection) bit.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The R40 HDMI PHY seems to be different to the A64 one, the A64 one
has no input mux, but the R40 one has.
Drop the A64 fallback compatible from the HDMI PHY node in R40 DT.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: Fix subject prefix order]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The next update of libfdt has a new dependency on INT_MAX. Update the
instances of libfdt_env.h in the kernel to either include the necessary
header with the definition or define it locally.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Switch to the new coresight bindings for hardware ports
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add fixed regulators for the ADC. This board does not have
a programmable PMIC, but fixed regulators.
Adding them to DT so the ADC can probe correctly.
Tested-by: Swapna Gurumani <swapna.gurumani@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/at91-dvk_som60.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/eeprom@87: I2C bus unit address format error, expected "57"
arch/arm/boot/dts/at91-dvk_som60.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/ft5426@56: I2C bus unit address format error, expected "38"
arch/arm/boot/dts/at91-vinco.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f8024000/rtc@64: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/at91sam9260ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9g20ek_2mmc.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9g20ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9261ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/tsc2046@0: SPI bus unit address format error, expected "2"
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Switch to the new the hardware port bindings.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
It may happen that when we relocate the kernel we corrupt other
sensible memory (e.g. the memory needed by U-Boot for dealing
with bootm command) while copying the kernel. If we overwrite
the content of the memory area used by U-Boot's command bootm
(described by U-Boot's parameters bootm_low and bootm_size),
the kernel won't be able to boot. Troubleshooting the problem
then is not straightforward.
This commit allows the user to easily print information on
where the kernel gets copied from/to in order to help with the
design of the system memory map (e.g. bootm_low and bootm_size)
at boot up.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Acked-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@52: I2C bus unit address format error, expected "34"
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@53: I2C bus unit address format error, expected "35"
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@54: I2C bus unit address format error, expected "36"
arch/arm/boot/dts/zynq-zc770-xm013.dtb: Warning (spi_bus_reg): /amba/spi@e0006000/eeprom@0: SPI bus unit address format error, expected "2"
arch/arm/boot/dts/zynq-zc770-xm010.dtb: Warning (spi_bus_reg): /amba/spi@e0007000/flash@0: SPI bus unit address format error, expected "1"
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add the resets property for all the timers on the Cyclone5/Arria5/Arria10
platforms.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
We need this new compatibility string as we experienced different behavior
for this 10/100Mbits/s macb interface on this particular SoC.
Backward compatibility is preserved as we keep the alternative strings.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dtc has new checks for SPI buses. The rk3036 dts file has a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- UART0 was missing the bus clock ("apb_pclk").
- Use recently accepted r9a06g032 and rzn1 compat strings.
- Add all the other UARTs.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
[simon: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
dtc has new checks for I2C buses. The sun9i-a80 dts file has a node named
'i2c' which causes a false positive warning. As the node is a RSB bus,
correct the node name to be 'rsb' to fix the warnings.
arch/arm/boot/dts/sun9i-a80-cubieboard4.dtb: Warning (i2c_bus_reg): /soc/i2c@8003400/codec@e89:reg: I2C address must be less than 10-bits, got "0xe89"
arch/arm/boot/dts/sun9i-a80-cubieboard4.dtb: Warning (i2c_bus_reg): /soc/i2c@8003400/pmic@745:reg: I2C address must be less than 10-bits, got "0x745"
arch/arm/boot/dts/sun9i-a80-optimus.dtb: Warning (i2c_bus_reg): /soc/i2c@8003400/codec@e89:reg: I2C address must be less than 10-bits, got "0xe89"
arch/arm/boot/dts/sun9i-a80-optimus.dtb: Warning (i2c_bus_reg): /soc/i2c@8003400/pmic@745:reg: I2C address must be less than 10-bits, got "0x745"
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dtb: Warning (i2c_bus_reg): /soc/i2c@ffc04000/adxl345@0: I2C bus unit address format error, expected "53"
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Provide aliases to each i2c bus per labels added for
each PCIe slot, etc, that are downstream beyond a mux.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
dtc has new checks for I2C buses. The ASpeed dts files have a node named
'i2c' which causes a false positive warning. As the node is a 'simple-bus',
correct the node name to be 'bus' to fix the warnings.
arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-opp-romulus.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-ast2500-evb.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-opp-zaius.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-quanta-q71l.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
dtc has new checks for SPI buses. Fix the warnings in node names.
arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dtb: Warning (spi_bus_bridge): /axi@18000000/qspi@27200: node name for SPI buses should be 'spi'
arch/arm/boot/dts/bcm958525er.dtb: Warning (spi_bus_bridge): /axi/qspi@27200: node name for SPI buses should be 'spi'
arch/arm/boot/dts/bcm958525xmc.dtb: Warning (spi_bus_bridge): /axi/qspi@27200: node name for SPI buses should be 'spi'
arch/arm/boot/dts/bcm958622hr.dtb: Warning (spi_bus_bridge): /axi/qspi@27200: node name for SPI buses should be 'spi'
arch/arm/boot/dts/bcm958625hr.dtb: Warning (spi_bus_bridge): /axi/qspi@27200: node name for SPI buses should be 'spi'
arch/arm/boot/dts/bcm988312hr.dtb: Warning (spi_bus_bridge): /axi/qspi@27200: node name for SPI buses should be 'spi'
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There are various places inside this dtsi file where 8 spaces where used
for indenting instead of tabs.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The PCI range is invalid and PCI attached devices doen't work.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
while compiling an ipq4019 target, dtc will complain:
regulator@b089000 unit address format error, expected "2089000"
The saw0 regulator reg value seems to be
copied and pasted from qcom-ipq8064.dtsi.
This patch fixes the reg value to match that of the
unit address which in turn silences the warning.
(There is no driver for qcom,saw2 right now.
So this went unnoticed)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds some operating points for cpu frequeny scaling
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
v1 was the incorrect choice here and sometimes the board
would not come up properly.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds device tree bindings for the tsl2772 ALS / proximity
sensor for the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds device tree bindings for the mpu6515 to the LG Nexus 5
(hammerhead) phone. Confirmed that the gyroscope / accelerometer
(mpu6515), magnetometer (ak8963), and temperature / pressure (bmp280)
sensors are available on the phone.
Interrupts are not working properly on the ak8963 magnetometer so they
are currently not configured.
The bmp280 retuns temperature/pressure measurement skipped errors but
will reliably work if I run:
echo 1 > in_pressure_oversampling_ratio
echo 1 > in_temp_oversampling_ratio
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the dt nodes for enabling the leds and gpio-buttons.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The nodes in ipq8064-ap148.dts currently are common with
boards that we will add next. So move the common data to
ipq8064-v.1.0.dtsi.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Change the third field of the "interrupts" property from
IRQ_TYPE_NONE to the correct value.
I do not have hardware documentation for these devices, so I
followed a mail list suggestion to copy the flag values from the same
type of node in arch/arm64/boot/dts/qcom/msm8916.dtsi
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Cosmetic change of integer value "0" in the third field of the
"interrupts" property to the correct named constant.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Cosmetic change of integer value "4" in the third field of the
"interrupts" property to the correct named constant.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Cosmetic change of integer value "1" in the third field of the
"interrupts" property to the correct named constant.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Cosmetic change of integer value "0" in the first field of the
"interrupts" property to the correct named constant.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Cosmetic change of integer value "1" in the first field of the
"interrupts" property to the correct named constant.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Switch Register Access Block (SRAB) has one interrupt for link state
change on each ports (0-5, 7-8) a PHY interrupt, timestamping interrupt
and sleep timer interrupts for each management ports (5,7,8). Wire those
up so we can utilize them to speed up link resolution.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable the SFP connected to port 5 of the switch and wire up all GPIOs
to the SFP cage. Because of a hardware limitation of the i2c controller
on the iProc SoCs which prevents large i2c (> 63 bytes) transactions to
work, we use the i2c-gpio interface instead, which does not have that
limitation. This allows us to read the SFP module EEPROM, which would
not be possible otherwise since it exceeds that size during a single
read transfer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
The drive strength has to be set to medium otherwise some data
corruption may happen.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This adds labels to commonly used device-tree nodes so that derivative
boards can avoid ahb/apb hierarchy.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The maximum CPU frequency for the i.MX53 QSB is 1GHz, so disable the
1.2GHz OPP. This makes the board work again with configs that have
cpufreq enabled like imx_v6_v7_defconfig on which the board stopped
working with the addition of cpufreq-dt support.
Fixes: 791f416608 ("ARM: dts: imx53: add cpufreq-dt support")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This board, as well as some other boards with i.MX6 and a PMIC, uses a
"PMIC_STBY_REQ" line to notify the PMIC about a state change.
The PMIC is programmed for a specific state change before triggering the
line.
In this case, PMIC_STBY_REQ can be used for stand by, sleep
and power off modes.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds nodes for the Video Engine and the associated reserved memory
for the A33. Up to 96 MiB of memory are dedicated to the CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds nodes for the Video Engine and the associated reserved memory
for the A20. Up to 96 MiB of memory are dedicated to the CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds nodes for the Video Engine and the associated reserved memory
for sun5i-based platforms. Up to 96 MiB of memory are dedicated to the
CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable support for SDHCI controller number 2 and add required regulator
for external SD card.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
S2MPS14 PMIC interrupt line on Exynos3250-based Artik5 evaluation board
has external pull-up resistors, so disable any pull control for it in
controller node. This fixes support for S2MPS14 PMIC interrupts and
enables operation of wakeup from S2MPS14 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The pinctrl properties on the IOMUXC node get overwritten by the
carrier board level device tree, hence the pinctrl_reset_moci
pinctrl does not get applied.
Associate the pinctrl_reset_moci pinctrl with the PCIe node where
we also make use of the pin as a reset GPIO.
Since the pin is muxed as a GPIO by default not muxing it explicitly
worked fine in practise.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no need to keep the PMU disabled.
Enable it like it is done in the other i.MX dtsi files.
With this change applied we see:
[ 1.338866] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board typically has 2 populated SFF interfaces. The mv88e6xxx
driver currently supports SFF modules connected to ports 9 and 10 of
the mv88e6390. Add support for sff2, which is connected to port 9.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The switch has an SFF attached to port 5. Add the SFF device, the
pinmux for its GPIOs, and list the port in the switch configuration.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SN65HVS882 load trigger is attached to GPIO2_23 on the AM571x IDK.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM572x-IDK rev 1.3A has tricolor RGB LEDs that can be controlled using
GPIO. Expose these to userspace for usage as necessary.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM571x-IDK rev 1.2A has tricolor RGB LEDs that can be controlled using
GPIO. Expose these to userspace for usage as necessary.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GTA04A5 has been produced with MCP chips either with
512MB RAM + 512MB NAND
512MB RAM + 1024MB NAND
1024MB RAM + 512MB OneNAND
RAM setup is done by U-Boot (MLO/SPL) but OneNAND needs
a different setup of the GPMC. So we need to derive a
DTB variant that modifies the gpmc and nand setup.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Properly pinmux the bluetooth enable so that it is not floating.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sensors for acceleration, rotation, magnetic heading and
barometer have been replaced in the A5 variant.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GTA04A5 uses a ti,wl1837 WiFi/Bluetooth module. Overwrite
the mmc2 node and child.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GTA04A5 has an improved IrDA circuit that can enable/disable
the receiver individually. We do not have an IrDA driver/subsystem
and hence the receiver should be actively turned off to save power,
especially in suspend.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GTA04 is the project name and Letux 2804 the product name.
Report both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GTA04 is the project name and Letux 2804 the product name.
Report both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GTA04 is the project name and Letux 2804 the product name.
Report both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GTA04 audio system makes use of all four McBSP ports, so enable and
connect them with pinmux.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GTA04 audio system makes use of all four McBSP ports, so set
up proper pinmux.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ISP needs camera pinmux (which is referenced by the camera node).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GTA04 has an optional OV9655 camera (for which we do
not yet have a driver upstream), but the ISP hardware
connection description in the device tree is independent
of that.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GTA04 can detect presence/absence or plug-in of an external
GPS antenna through a gpio. The best match for an event code
is SW_LINEIN_INSERT.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we can replace magic numbers by symbolic constants now.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are neither CD nor WP switches for mmc1. The µSD slot is
located under the SIM card under the battery and not accessible
during operation.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
vaux2 should remain always on since a higher potential at vio
could potentially damage the itg3200 sensor.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make clear how to use the wifi_reset since it is not obvious.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed to make the display and venc work properly.
Compare to omap3-beagle.dts.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
to better match omap3-beagle.dts (which was the basis
of designing the GTA04).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Vendor defined U-Boot has changed the partition scheme a while ago:
* kernel partition 6MB
* file system partition uses the remainder up to end of the NAND
* increased size of the environment partition (to get an OneNAND compatible base address)
* shrink the U-Boot partition
Let's be compatible (e.g. Debian kernel built from upstream).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we fix penirq polarity, add penirq pinmux and touchscreen
properties.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap dss susbystem takes the display aliases to find
out which displays exist. To enable tv-out we must define
an alias.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VENC with external OPA362 amplifier needs a special
"pinmux" setup in DEVCONF1 (TVOUTBYPASS and TVOUTACEN).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* fix connector compatibility (composite)
* add comment for gpio1 23
* add proper #address-cells
* we use only one venc_out channel for composite
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
needed for device variants based on GTA04 board but with
different display panel (driver).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
tab+space -> tab only for /* GSM audio */
spaces -> tab for dss_dpi_pins
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
S5M8767 PMIC interrupt line on Exynos5250-based Arndale board has
external pull-up resistors, so disable any pull control for it in
in controller node. This fixes support for S5M8767 interrupts and
enables operation of wakeup from S5M8767 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The SDHCI standard, MMC host controller bindings and MMC core defines
card detect pin as active low. Therefore there is no point to invert it
twice.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
PMIC node requires external interrupts for proper operation. Lack of them
was probably caused by a limited support for interrupts from more than one
parent, which was not possible to define when support for this board was
added. Fix this by adding 'interrupt-extended' property and properly
define both interrupt lines for PMIC node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
PMIC_IRQB and PMIC_KEYINB lines on Exynos4210-based Origen board have
external pull-up resistors, so disable any pull control for those lines
in respective pin controller node. This fixes support for MAX8997
interrupts and enables operation of wakeup from MAX8997 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 17419726aa ("ARM: dts: add max8997 device node for exynos4210-origen board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace the hardcoded clock indices by R9A06G032_CLK_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the LAN7515 on Raspberry Pi 3B+ doesn't have an EEPROM and the OTP
is empty, we need to enable the Ethernet LEDs via Device Tree.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Add the core display subsystem and vop nodes to rk3188.
Vop0 has a fully dedicated set of pins and only vop1 needs to
do pinctrl to have display output, so also add the necessary
pinctrl entries for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by Sandy Huang <hjc@rock-chips.com>
This patch enable the AHCI controller.
Since this controller need two regulator, this patch add them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
R40 have a sata controller which is the same as A20.
This patch adds a DT node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The clock controller registers are not 0x460 wide because the reset
controller starts at CBUS 0x4404. This currently overlaps with the
clock controller (which is at CBUS 0x4000).
There is no public documentation available on the actual size of the
clock controller's register area (also called "HHI"). However, in
Amlogic's GPL kernel sources the last "HHI" register is
HHI_HDMI_PHY_CNTL2 at CBUS + 0x43a8. 0x400 was chosen because that size
doesn't seem unlikely.
Fixes: 4a69fcd3a1 ("ARM: meson: Add DTS for Odroid-C1 and Tronfy MXQ boards")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock controller registers are not 0x460 wide because the reset
controller starts at CBUS 0x4404. This currently overlaps with the
clock controller (which is at CBUS 0x4000).
There is no public documentation available on the actual size of the
clock controller's register area (also called "HHI"). However, in
Amlogic's GPL kernel sources the last "HHI" register is
HHI_HDMI_PHY_CNTL2 at CBUS + 0x43a8. 0x400 was chosen because that size
doesn't seem unlikely.
Fixes: 2c323c43a3 ("ARM: dts: meson8: add and use the real clock controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Make use of the recently added &pinctrl and &watchdog labels. This
makes the whole file consistent and knowledge of the ahb/apb structure
is hidden.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Make use of the recently added &pinctrl and &watchdog labels. This
makes the whole file consistent and knowledge of the ahb/apb structure
is hidden.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
NOR and IFC controller connectivity is big-endian.
So add big-endian field in nor device tree node allowing
IFC controller to read/write data from/to the flash correctly.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6ULL is a lite version of i.MX6UL, its full name
is i.MX6 UltraLiteLite, NOT UlltraLite.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SLL has GPIO clock gates in CCM CCGR, add
clock property for GPIO driver to make sure all
GPIO banks work as expected.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signals available on both i.MX6UL and i.MX6ULL should have the same name
because it is the case of all others common signals, it avoids to make
mistakes (use the wrong ones) and it makes writing device tree files
less complicated. For example:
imx6ul-imx6ull-board.dtsi:
...
pinctrl_uart5: uart5grp {
fsl,pins = <
MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
>;
};
imx6ul-board.dts:
#include <imx6ul.dtsi>
#include <imx6ul-imx6ull-board.dtsi>
...
imx6ull-board.dts:
#include <imx6ull.dtsi>
#include <imx6ul-imx6ull-board.dtsi>
...
Without this patch, the imx6ull-board.dtb will use
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX instead of
MX6ULL_PAD_UART5_RX_DATA__UART5_DCE_RX and the uart5 will be
misconfigured.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Setting a stdout-path in the .dtb is convenient because then the user
gets a serial console on the RS-232 connector without any extra effort
of figuring out the relevant 'console=' boot parameter.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The WaRP7 has one mikroBUS socket on the back to plug click boards.
This patch allows to interact with some of these
i2c modules (EEPROM, RTC and so on).
Signed-off-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation" is based on the 1.5 version
of the i.Core MX6 cpu module. The 1.5 version differs from the original one for
a few details, including the ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup do to un-clocked
PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Fixes: 3fe0883577 ("ARM: dts: imx6q: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 1.5 version of Engicam's i.Core MX6 CPU module features a different clock
provider for the ethernet's PHY interface. Adjust the FEC ptp clock to
reference CLK_ENET_REF clock source, and set SION bit of
MX6QDL_PAD_GPIO_16__ENET_REF_CLK to adjust the input path of that pin.
The newly introduced imx6ql-icore-1.5.dtsi allows to collect in a single
place differences between version '1.0' and '1.5' of the module.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move usdhc2 and gpmi along with pinctrl nodes on
imx6ul-isiot.dtsi from dts files and mark it as 'disabled'
and the relevant dts will enable the status as 'okay'
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Define the Messaging Unit (MU) for i.MX7 in the processor's dtsi.
The respective driver is added in the next commit.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX7ULP B0 chip has some pin changes for USB and VIU
module, update pinfunc header file accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MC13892 Analog-to-Digital input pins (ADIN5-7) are exposed on the
imx51-babbage board.
Pass the "fsl,mc13xxx-uses-adc" property so that the MC13892 ADC
block can work.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX6SLL pinctrl driver, for details, please refer to
Documentation/devicetree/bindings/gpio/gpio.txt of "gpio-ranges"
property.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.
There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.
And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.
-----BEGIN PGP SIGNATURE-----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=CHc2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants against v4.19-rc1
These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.
There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.
And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.
* tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Signed-off-by: Olof Johansson <olof@lixom.net>
Add 3 helpers so that pincontrol definitions for pxa25x and pxa27x are
easier, and can be easily converted from old mfp mach-pxa code to
devicetree.
An example of such conversion would be :
static unsigned long mioa701_pin_config[] = {
GPIO32_MMC_CLK,
GPIO92_MMC_DAT_0,
GPIO109_MMC_DAT_1,
GPIO110_MMC_DAT_2,
GPIO111_MMC_DAT_3,
GPIO112_MMC_CMD,
MIO_CFG_IN(GPIO78_SDIO_RO, AF0),
MIO_CFG_IN(GPIO15_SDIO_INSERT, AF0),
MIO_CFG_OUT(GPIO91_SDIO_EN, AF0, DRIVE_LOW),
};
into:
pinctrl_mmc_default: mmc-default {
PMMUX(sd-insert, 15, gpio_in);
PMMUX(mmclk, 32, MMCLK);
PMMUX(sd-ro, 78, gpio_in);
PMMUX_LPM_LOW(sd-enable, 91, gpio_out);
PMMUX(mmdat0, 92, MMDAT<0>);
PMMUX(mmdat1, 109, MMDAT<1>);
PMMUX(mmdat2, 110, MMDAT<2>);
PMMUX(mmdat3, 111, MMDAT<3>);
PMMUX(mmcmd, 112, MMCMD);
};
The third column of PMMUX*() helpers can be found in pincontrol muxing
functions, either in pinctrl-pxa27x.c (or pinctrl-pxa25x.c), or by
inspecting the pincontrol once booted in debugfs.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Marcel Ziswiler