Commit Graph

13 Commits

Author SHA1 Message Date
Linus Walleij 25c8e03bdb spi/pl022: move probe call to subsys_initcall()
The PL022 SPI bus is sometimes used for early stuff like
regulators that need to be present at module_init() time, so
we move this to a subsys_initcall().

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-09-08 22:50:10 -06:00
Linus Walleij 545074fb95 spi/pl022: fix APB pclk power regression on U300
With the introduction of an AMBA PrimeCell per-cell block clock,
the pclk was left on after probe() unless explicitly disabled.
This clock is wired to the same clock on PL022 causing it to stay
always on since.

Fix this up properly by clocking the pclk whenever we want to
write into any PL022 registers and clocking the external clock
whenever we want to transmit messages on the bus.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by : Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-09-08 12:24:30 -06:00
Kevin Wells b4225885de spi/amba_pl022: Fix probe and remove hook section annotations.
Probe and remove hooks belong in the __devinit and __devexit sections
respectively.  This patch fixes incorrect annotations on the pl022 spi
driver.

Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-08-01 01:35:29 -06:00
Grzegorz Sygieda 4a12404dda spi/pl022: fix stop queue procedure
This fix prevents queue being marked as "stopped", if data exists
in the queue list.

Signed-off-by: Grzegorz Sygieda <grzegorz.sygieda@tieto.com>
Signed-off-by: Lukasz Baj <lukasz.baj@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-25 00:23:14 -06:00
Linus Walleij 781c7b129b spi/pl022: add support for the PL023 derivate
This adds support for a further ST variant of the PL022 called
PL023. Some differences in the control registers due to being
stripped down to SPI mode only, and a new clock feedback sample
delay config setting is available.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-25 00:23:14 -06:00
Linus Walleij 556f4aeb7d spi/pl022: fix up differences between ARM and ST versions
The PL022 SPI driver did not cleanly separate between the
original unmodified ARM version and the ST Microelectronics
versions. Split this more cleanly and fix some whitespace
moaning from checkpatch at the same time.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-25 00:23:13 -06:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Linus Walleij fc05475f86 ARM: 5893/1: SPI AMBA PL022: Limit TX FIFO fills
Added logic to cap TX FIFO fill size based on current free RX
FIFO entries instead of TX status flags. This is to prevent
an issue with RX FIFO overflows.

Signed-off-by: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-01-27 22:00:46 +00:00
Srinidhi Kasagar e89e04fcdc ARM: 5741/1: pl022: fix peripheral id for ST vendor
This fixes the wrong peripheral id being
used in pl022 driver for ST derivative.

Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-05 17:55:55 +01:00
Russell King 59b69e27ca Merge branch 'u300' into devel 2009-09-21 16:03:13 +01:00
Linus Walleij ee2b805c8e ARM: 5678/1: SSP/SPI PL022 polarity terminology fix
The definition of the SPI clock phase for the Motorola mode of
the PL022 driver was incorrect: the spec had been interpreted as
data being recieved on rising or falling edge of the clocks while
the correct interpretation is that data can be recieved on the
first or second edge transition, falling or rising depending on
the polarity setting.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-09-18 22:09:02 +01:00
Huang Weiyi 0724915a69 [ARM] remove duplicated #include
Remove duplicated #include('s) in
  drivers/spi/amba-pl022.c

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-11 16:55:51 +01:00
Linus Walleij b43d65f7e8 [ARM] 5546/1: ARM PL022 SSP/SPI driver v3
This adds a driver for the ARM PL022 PrimeCell SSP/SPI
driver found in the U300 platforms as well as in some
ARM reference hardware, and in a modified version on the
Nomadik board.

Reviewed-by: Alessandro Rubini <rubini-list@gnudd.com>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-10 22:39:52 +01:00