Pull x86/apic changes from Ingo Molnar:
"Main changes:
- Multiple MSI support added to the APIC, PCI and AHCI code - acked
by all relevant maintainers, by Alexander Gordeev.
The advantage is that multiple AHCI ports can have multiple MSI
irqs assigned, and can thus spread to multiple CPUs.
[ Drivers can make use of this new facility via the
pci_enable_msi_block_auto() method ]
- x86 IOAPIC code from interrupt remapping cleanups from Joerg
Roedel:
These patches move all interrupt remapping specific checks out of
the x86 core code and replaces the respective call-sites with
function pointers. As a result the interrupt remapping code is
better abstraced from x86 core interrupt handling code.
- Various smaller improvements, fixes and cleanups."
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess
x86, kvm: Fix intialization warnings in kvm.c
x86, irq: Move irq_remapped out of x86 core code
x86, io_apic: Introduce eoi_ioapic_pin call-back
x86, msi: Introduce x86_msi.compose_msi_msg call-back
x86, irq: Introduce setup_remapped_irq()
x86, irq: Move irq_remapped() check into free_remapped_irq
x86, io-apic: Remove !irq_remapped() check from __target_IO_APIC_irq()
x86, io-apic: Move CONFIG_IRQ_REMAP code out of x86 core
x86, irq: Add data structure to keep AMD specific irq remapping information
x86, irq: Move irq_remapping_enabled declaration to iommu code
x86, io_apic: Remove irq_remapping_enabled check in setup_timer_IRQ0_pin
x86, io_apic: Move irq_remapping_enabled checks out of check_timer()
x86, io_apic: Convert setup_ioapic_entry to function pointer
x86, io_apic: Introduce set_affinity function pointer
x86, msi: Use IRQ remapping specific setup_msi_irqs routine
x86, hpet: Introduce x86_msi_ops.setup_hpet_msi
x86, io_apic: Introduce x86_io_apic_ops.print_entries for debugging
x86, io_apic: Introduce x86_io_apic_ops.disable()
x86, apic: Mask IO-APIC and PIC unconditionally on LAPIC resume
...
Pull perf changes from Ingo Molnar:
"There are lots of improvements, the biggest changes are:
Main kernel side changes:
- Improve uprobes performance by adding 'pre-filtering' support, by
Oleg Nesterov.
- Make some POWER7 events available in sysfs, equivalent to what was
done on x86, from Sukadev Bhattiprolu.
- tracing updates by Steve Rostedt - mostly misc fixes and smaller
improvements.
- Use perf/event tracing to report PCI Express advanced errors, by
Tony Luck.
- Enable northbridge performance counters on AMD family 15h, by Jacob
Shin.
- This tracing commit:
tracing: Remove the extra 4 bytes of padding in events
changes the ABI. All involved parties (PowerTop in particular)
seem to agree that it's safe to do now with the introduction of
libtraceevent, but the devil is in the details ...
Main tooling side changes:
- Add 'event group view', from Namyung Kim:
To use it, 'perf record' should group events when recording. And
then perf report parses the saved group relation from file header
and prints them together if --group option is provided. You can
use the 'perf evlist' command to see event group information:
$ perf record -e '{ref-cycles,cycles}' noploop 1
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.385 MB perf.data (~16807 samples) ]
$ perf evlist --group
{ref-cycles,cycles}
With this example, default perf report will show you each event
separately.
You can use --group option to enable event group view:
$ perf report --group
...
# group: {ref-cycles,cycles}
# ========
# Samples: 7K of event 'anon group { ref-cycles, cycles }'
# Event count (approx.): 6876107743
#
# Overhead Command Shared Object Symbol
# ................ ....... ................. ..........................
99.84% 99.76% noploop noploop [.] main
0.07% 0.00% noploop ld-2.15.so [.] strcmp
0.03% 0.00% noploop [kernel.kallsyms] [k] timerqueue_del
0.03% 0.03% noploop [kernel.kallsyms] [k] sched_clock_cpu
0.02% 0.00% noploop [kernel.kallsyms] [k] account_user_time
0.01% 0.00% noploop [kernel.kallsyms] [k] __alloc_pages_nodemask
0.00% 0.00% noploop [kernel.kallsyms] [k] native_write_msr_safe
0.00% 0.11% noploop [kernel.kallsyms] [k] _raw_spin_lock
0.00% 0.06% noploop [kernel.kallsyms] [k] find_get_page
0.00% 0.02% noploop [kernel.kallsyms] [k] rcu_check_callbacks
0.00% 0.02% noploop [kernel.kallsyms] [k] __current_kernel_time
As you can see the Overhead column now contains both of ref-cycles
and cycles and header line shows group information also - 'anon
group { ref-cycles, cycles }'. The output is sorted by period of
group leader first.
- Initial GTK+ annotate browser, from Namhyung Kim.
- Add option for runtime switching perf data file in perf report,
just press 's' and a menu with the valid files found in the current
directory will be presented, from Feng Tang.
- Add support to display whole group data for raw columns, from Jiri
Olsa.
- Add per processor socket count aggregation in perf stat, from
Stephane Eranian.
- Add interval printing in 'perf stat', from Stephane Eranian.
- 'perf test' improvements
- Add support for wildcards in tracepoint system name, from Jiri
Olsa.
- Add anonymous huge page recognition, from Joshua Zhu.
- perf build-id cache now can show DSOs present in a perf.data file
that are not in the cache, to integrate with build-id servers being
put in place by organizations such as Fedora.
- perf top now shares more of the evsel config/creation routines with
'record', paving the way for further integration like 'top'
snapshots, etc.
- perf top now supports DWARF callchains.
- Fix mmap limitations on 32-bit, fix from David Miller.
- 'perf bench numa mem' NUMA performance measurement suite
- ... and lots of fixes, performance improvements, cleanups and other
improvements I failed to list - see the shortlog and git log for
details."
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (270 commits)
perf/x86/amd: Enable northbridge performance counters on AMD family 15h
perf/hwbp: Fix cleanup in case of kzalloc failure
perf tools: Fix build with bison 2.3 and older.
perf tools: Limit unwind support to x86 archs
perf annotate: Make it to be able to skip unannotatable symbols
perf gtk/annotate: Fail early if it can't annotate
perf gtk/annotate: Show source lines with gray color
perf gtk/annotate: Support multiple event annotation
perf ui/gtk: Implement basic GTK2 annotation browser
perf annotate: Fix warning message on a missing vmlinux
perf buildid-cache: Add --update option
uprobes/perf: Avoid uprobe_apply() whenever possible
uprobes/perf: Teach trace_uprobe/perf code to use UPROBE_HANDLER_REMOVE
uprobes/perf: Teach trace_uprobe/perf code to pre-filter
uprobes/perf: Teach trace_uprobe/perf code to track the active perf_event's
uprobes: Introduce uprobe_apply()
perf: Introduce hw_perf_event->tp_target and ->tp_list
uprobes/perf: Always increment trace_uprobe->nhit
uprobes/tracing: Kill uprobe_trace_consumer, embed uprobe_consumer into trace_uprobe
uprobes/tracing: Introduce is_trace_uprobe_enabled()
...
Hotplug
PCI/PM: Clean up PME state when removing a device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zdXb
-----END PGP SIGNATURE-----
Merge tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This is another fix for v3.8. It fixes an oops that happens when a
Thunderbolt adapter is unplugged (remove device, poll for PME events
on no-longer-existing device, oops)."
* tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PM: Clean up PME state when removing a device
Devices are added to pci_pme_list when drivers use pci_enable_wake()
or pci_wake_from_d3(), but they aren't removed from the list unless
the driver explicitly disables wakeup. Many drivers never disable
wakeup, so their devices remain on the list even after they are
removed, e.g., via hotplug. A subsequent PME poll will oops when
it tries to touch the device.
This patch disables PME# on a device before removing it, which removes
the device from pci_pme_list. This is safe even if the device never
had PME# enabled.
This oops can be triggered by unplugging a Thunderbolt ethernet adapter
on a Macbook Pro, as reported by Daniel below.
[bhelgaas: changelog]
Reference: http://lkml.kernel.org/r/CAMVG2svG21yiM1wkH4_2pen2n+cr2-Zv7TbH3Gj+8MwevZjDbw@mail.gmail.com
Reported-and-tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
The new function pci_enable_msi_block_auto() tries to allocate
maximum possible number of MSIs up to the number the device
supports. It generalizes a pattern when pci_enable_msi_block()
is contiguously called until it succeeds or fails.
Opposite to pci_enable_msi_block() which takes the number of
MSIs to allocate as a input parameter,
pci_enable_msi_block_auto() could be used by device drivers to
obtain the number of assigned MSIs and the number of MSIs the
device supports.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/c3de2419df94a0f95ca1a6f755afc421486455e6.1353324359.git.agordeev@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Hotplug
PCI: pciehp: Use per-slot workqueues to avoid deadlock
PCI: shpchp: Make shpchp_wq non-ordered
PCI: shpchp: Handle push button event asynchronously
PCI: shpchp: Use per-slot workqueues to avoid deadlock
Power management
PCI: Allow pcie_aspm=force even when FADT indicates it is unsupported
Misc
PCI/AER: pci_get_domain_bus_and_slot() call missing required pci_dev_put()
PCI: remove depends on CONFIG_EXPERIMENTAL
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=lhvi
-----END PGP SIGNATURE-----
Merge tag '3.8-pci-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"The most important is a fix for a pciehp deadlock that occurs when
unplugging a Thunderbolt adapter. We also applied the same fix to
shpchp, removed CONFIG_EXPERIMENTAL dependencies, fixed a
pcie_aspm=force problem, and fixed a refcount leak.
Details:
- Hotplug
PCI: pciehp: Use per-slot workqueues to avoid deadlock
PCI: shpchp: Make shpchp_wq non-ordered
PCI: shpchp: Handle push button event asynchronously
PCI: shpchp: Use per-slot workqueues to avoid deadlock
- Power management
PCI: Allow pcie_aspm=force even when FADT indicates it is unsupported
- Misc
PCI/AER: pci_get_domain_bus_and_slot() call missing required pci_dev_put()
PCI: remove depends on CONFIG_EXPERIMENTAL"
* tag '3.8-pci-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: remove depends on CONFIG_EXPERIMENTAL
PCI: Allow pcie_aspm=force even when FADT indicates it is unsupported
PCI: shpchp: Use per-slot workqueues to avoid deadlock
PCI: shpchp: Handle push button event asynchronously
PCI: shpchp: Make shpchp_wq non-ordered
PCI/AER: pci_get_domain_bus_and_slot() call missing required pci_dev_put()
PCI: pciehp: Use per-slot workqueues to avoid deadlock
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Right now using pcie_aspm=force will not enable ASPM if the FADT indicates
ASPM is unsupported. However, the semantics of force should probably allow
for this, especially as they did before 3c076351c4 ("PCI: Rework ASPM
disable code")
This patch just skips the clearing of any ASPM setup that the firmware has
carried out on this bus if pcie_aspm=force is being used.
Reference: http://bugs.launchpad.net/bugs/962038
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
When we have an SHPC-capable bridge with a second SHPC-capable bridge
below it, pushing the upstream bridge's attention button causes a
deadlock.
The deadlock happens because we use the shpchp_wq workqueue to run
shpchp_pushbutton_thread(), which uses shpchp_disable_slot() to remove
devices below the upstream bridge. When we remove the downstream bridge,
we call shpc_remove(), the shpchp driver's .remove() method. That calls
flush_workqueue(shpchp_wq), which deadlocks because the
shpchp_pushbutton_thread() work item is still running.
This patch avoids the deadlock by creating a workqueue for every slot
and removing the single shared workqueue.
Here's the call path that leads to the deadlock:
shpchp_queue_pushbutton_work
queue_work(shpchp_wq) # shpchp_pushbutton_thread
...
shpchp_pushbutton_thread
shpchp_disable_slot
remove_board
shpchp_unconfigure_device
pci_stop_and_remove_bus_device
...
shpc_remove # shpchp driver .remove method
hpc_release_ctlr
cleanup_slots
flush_workqueue(shpchp_wq)
This change is based on code inspection, since we don't have hardware
with this topology.
Based-on-patch-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
Use non-ordered workqueue for attention button events.
Attention button events on each slot can be handled asynchronously. So
we should use non-ordered workqueue. This patch also removes ordered
workqueue in shpchp as a result.
486b10b9f4 ("PCI: pciehp: Handle push button event asynchronously") made
the same change to pciehp. I split this out from a patch by Yijing Wang
<wangyijing@huawei.com> so we fix one thing at a time and to make the
shpchp history correspond more closely with the pciehp history.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
e24dcbef93 ("shpchp: update workqueue usage") was described as adding
non-ordered shpchp_wq, but it actually made it an *ordered* workqueue.
This patch changes shpchp_wq to be non-ordered, as described in the
e24dcbef93 commit log and as was done for pciehp by a827ea307b ("pciehp:
update workqueue usage").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
The function aer_recover_queue() calls pci_get_domain_bus_and_slot(), which
requires that the caller decrement the reference count with pci_dev_put().
This patch adds the missing call to pci_dev_put().
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
CC: stable@vger.kernel.org
When we have a hotplug-capable PCIe port with a second hotplug-capable
PCIe port below it, removing the device below the upstream port causes
a deadlock.
The deadlock happens because we use the pciehp_wq workqueue to run
pciehp_power_thread(), which uses pciehp_disable_slot() to remove devices
below the upstream port. When we remove the downstream PCIe port, we call
pciehp_remove(), the pciehp driver's .remove() method. That calls
flush_workqueue(pciehp_wq), which deadlocks because the
pciehp_power_thread() work item is still running.
This patch avoids the deadlock by creating a workqueue for every PCIe port
and removing the single shared workqueue.
Here's the call path that leads to the deadlock:
pciehp_queue_pushbutton_work
queue_work(pciehp_wq) # queue pciehp_power_thread
...
pciehp_power_thread
pciehp_disable_slot
remove_board
pciehp_unconfigure_device
pci_stop_and_remove_bus_device
...
pciehp_remove # pciehp driver .remove method
pciehp_release_ctrl
pcie_cleanup_slot
flush_workqueue(pciehp_wq)
This is fairly urgent because it can be caused by simply unplugging a
Thunderbolt adapter, as reported by Daniel below.
[bhelgaas: changelog]
Reference: http://lkml.kernel.org/r/CAMVG2ssiRgcTD1bej2tkUUfsWmpL5eNtPcNif9va2-Gzb2u8nQ@mail.gmail.com
Reported-and-tested-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
Fix kernel-doc warning in iov.c:
Warning(drivers/pci/iov.c:752): No description found for parameter 'numvfs'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Sorry-by: Don Dutile <ddutile@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes make cper_print_aer more consistent with aer_print_error
and clean things up by elimiating the use of the prefix variable and
replacing it with dev_printk.
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com>
Acked-by: Boris Petkov <bp@alien8.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch will provide a more reliable and easy way for user-space
applications to have access to AER logs rather than reading them from the
message buffer. It also provides a way to notify user-space when an AER
event occurs.
The aer driver is updated to generate a trace event of function 'aer_event'
when a PCIe error is reported over the AER interface. The trace event was
added to both the interrupt based aer path and the firmware first path.
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Boris Petkov <bp@alien8.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Otherwise it fails like this on cards like the Transcend 16GB SDHC card:
mmc0: new SDHC card at address b368
mmcblk0: mmc0:b368 SDC 15.0 GiB
mmcblk0: error -110 sending status command, retrying
mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb0
Tested on my Lenovo x200 laptop.
[bhelgaas: changelog]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Chris Ball <cjb@laptop.org>
CC: Manoj Iyer <manoj.iyer@canonical.com>
CC: stable@vger.kernel.org
Ulrich reported that his USB3 cardreader does not work reliably when
connected to the USB3 port. It turns out that USB3 controller failed to
awaken when plugging in the USB3 cardreader. Further experiments found
that the USB3 host controller can only be awakened via polling, not via PME
interrupt. But if the PCIe port to which the USB3 host controller is
connected is suspended, we cannot poll the controller because its config
space is not accessible when the PCIe port is in a low power state.
To solve the issue, the PCIe port will not be suspended if any subordinate
device needs PME polling.
[bhelgaas: use bool consistently rather than mixing int/bool]
Reference: http://lkml.kernel.org/r/50841CCC.9030809@uli-eckhardt.de
Reported-by: Ulrich Eckhardt <usb@uli-eckhardt.de>
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v3.6+
If we request "num_vfs" and the driver's sriov_configure() method enables
exactly that number ("num_vfs_enabled"), we complain "Invalid value for
number of VFs to enable" and return an error. We should silently return
success instead.
Also, use kstrtou16() since numVFs is defined to be a 16-bit field and
rework to simplify control flow.
Reported-by: Greg Rose <gregory.v.rose@intel.com>
Reference: http://lkml.kernel.org/r/20121214101911.00002f59@unknown
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Donald Dutile <ddutile@redhat.com>
Pull s390 update from Martin Schwidefsky:
"Add support to generate code for the latest machine zEC12, MOD and XOR
instruction support for the BPF jit compiler, the dasd safe offline
feature and the big one: the s390 architecture gets PCI support!!
Right before the world ends on the 21st ;-)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (41 commits)
s390/qdio: rename the misleading PCI flag of qdio devices
s390/pci: remove obsolete email addresses
s390/pci: speed up __iowrite64_copy by using pci store block insn
s390/pci: enable NEED_DMA_MAP_STATE
s390/pci: no msleep in potential IRQ context
s390/pci: fix potential NULL pointer dereference in dma_free_seg_table()
s390/pci: use kmem_cache_zalloc instead of kmem_cache_alloc/memset
s390/bpf,jit: add support for XOR instruction
s390/bpf,jit: add support MOD instruction
s390/cio: fix pgid reserved check
vga: compile fix, disable vga for s390
s390/pci: add PCI Kconfig options
s390/pci: s390 specific PCI sysfs attributes
s390/pci: PCI hotplug support via SCLP
s390/pci: CHSC PCI support for error and availability events
s390/pci: DMA support
s390/pci: PCI adapter interrupts for MSI/MSI-X
s390/bitops: find leftmost bit instruction support
s390/pci: CLP interface
s390/pci: base support
...
Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay Pandarathil)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=OE3Q
-----END PGP SIGNATURE-----
Merge tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI update from Bjorn Helgaas:
"Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay
Pandarathil)"
Fix up trivial conflicts.
* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Use phys_addr_t for physical ROM address
x86/PCI: Add NumaChip remote PCI support
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
PCI: Add and use standard PCI-X Capability register names
PCI/PM: Keep runtime PM enabled for unbound PCI devices
xen-pcifront: Handle backend CLOSED without CLOSING
PCI: SRIOV control and status via sysfs (documentation)
PCI/AER: Report success only when every device has AER-aware driver
...
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
Use phys_addr_t rather than "void *" for physical memory address.
This removes casts and fixes a "cast from pointer to integer of different
size" warning on ppc44x_defconfig.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/bjorn-pcie-cap:
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
PCI: Add and use standard PCI-X Capability register names
Add standard #defines for ASPM fields in PCI Express Link Capability and
Link Control registers.
Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits. PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
* pci/mjg-pci-roms-from-efi:
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
Platforms may provide their own mechanisms for obtaining ROMs. Add support
for using data provided by the platform in that case.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Platforms may want to provide architecture-specific functionality during
PCI enumeration. Add a pcibios_add_device() call that architectures can
override to do so.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Add and use #defines for PCI-X Capability registers and fields.
Note that the PCI-X Capability has a different layout for
type 0 (endpoint) and type 1 (bridge) devices.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For unbound PCI devices, what we need is:
- Always in D0 state, because some devices do not work again after
being put into D3 by the PCI bus.
- In SUSPENDED state if allowed, so that the parent devices can still
be put into low power state.
To satisfy these requirements, the runtime PM for the unbound PCI
devices are disabled and set to SUSPENDED state. One issue of this
solution is that the PCI devices will be put into SUSPENDED state even
if the SUSPENDED state is forbidden via the sysfs interface
(.../power/control) of the device. This is not an issue for most
devices, because most PCI devices are not used at all if unbound.
But there are exceptions. For example, unbound VGA card can be used
for display, but suspending its parents makes it stop working.
To fix the issue, we keep the runtime PM enabled when the PCI devices
are unbound. But the runtime PM callbacks will do nothing if the PCI
devices are unbound. This way, we can put the PCI devices into
SUSPENDED state without putting the PCI devices into D3 state.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=48201
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v3.6+
Backend drivers shouldn't transition to CLOSED unless the frontend is
CLOSED. If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.
So, treat an unexpected backend CLOSED state the same as CLOSING.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Add SCLP PCI configure/deconfigure and implement a PCI hotplug
controller (s390_pci_hpc). The hotplug controller creates a slot
for every PCI function in stand-by or configured state. The PCI
functions are named after the PCI function ID (fid). By writing to
the power attribute in /sys/bus/pci/slots/<fid>/power the PCI function
is moved to stand-by or configured state. If moved to the configured
state the device is automatically scanned by the s390 PCI layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Support PCI adapter interrupts using the Single-IRQ-mode. Single-IRQ-mode
disables an adapter IRQ automatically after delivering it until the SIC
instruction enables it again. This is used to reduce the number of IRQs
for streaming workloads.
Up to 64 MSI handlers can be registered per PCI function.
A hash table is used to map interrupt numbers to MSI descriptors.
The interrupt vector is scanned using the flogr instruction.
Only MSI/MSI-X interrupts are supported, no legacy INTs.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p, __devint,
__devinitdata, __devinitconst, and _devexit are no longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is being removed so setup-bus always needs to be built
as part of PCI.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the demise of CONFIG_HOTPLUG as an option, the pci_uevent
function located in hotplug.c will now always be used and doesn't need
special treatment in the Makefile. Move pci_uevent into pci-driver.c
and remove hotplug.c
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an error is detected on a PCIe device which does not have an
AER-aware driver, prevent AER infrastructure from reporting
successful error recovery.
This is because the report_error_detected() function that gets
called in the first phase of recovery process allows forward
progress even when the driver for the device does not have AER
capabilities. It seems that all callbacks (in pci_error_handlers
structure) registered by drivers that gets called during error
recovery are not mandatory. So the intention of the infrastructure
design seems to be to allow forward progress even when a specific
callback has not been registered by a driver. However, if error
handler structure itself has not been registered, it doesn't make
sense to allow forward progress.
As a result of the current design, in the case of a single device
having an AER-unaware driver or in the case of any function in a
multi-function card having an AER-unaware driver, a successful
recovery is reported.
Typical scenario this happens is when a PCI device is detached
from a KVM host and the pci-stub driver on the host claims the
device. The pci-stub driver does not have error handling capabilities
but the AER infrastructure still reports that the device recovered
successfully.
The changes proposed here leaves the device(s)in an unrecovered state
if the driver for the device or for any device in the subtree
does not have error handler structure registered. This reflects
the true state of the device and prevents any partial recovery (or no
recovery at all) reported as successful.
[bhelgaas: changelog]
Signed-off-by: Vijay Mohan Pandarathil <vijaymohan.pandarathil@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linas Vepstas <linasvepstas@gmail.com>
Reviewed-by: Myron Stowe <myron.stowe@redhat.com>
ACPI routines for adding and removing device wakeup notifiers are
currently defined in a PCI-specific file, but they will be necessary
for non-PCI devices too, so move them to a separate file under
drivers/acpi and rename them to indicate their ACPI origins.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pci/misc:
PCI/ACPI: Notify PCI devices when their power resource is turned on
PCI: Add GPL license for drivers/pci/ioapic module
PCI: Fix bit definitions of PCI_EXP_LNKCAP2 register
Linus Torvalds