We provided the right semantics on open drain lines being
by definition output but incidentally the irq set up function
would only allow IRQs on lines that were "not output".
Fix the semantics to allow output open drain lines to be used
for IRQs.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Russell King <linux@armlinux.org.uk>
Cc: stable@vger.kernel.org # v5.3+
Link: https://lore.kernel.org/r/20200527140758.162280-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is to fix a crash:
[ ] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ ] general protection fault: 0000 [#1] SMP KASAN PTI
[ ] RIP: 0010:ipv6_local_error+0xac/0x7a0
[ ] Call Trace:
[ ] xfrm6_local_error+0x1eb/0x300
[ ] xfrm_local_error+0x95/0x130
[ ] __xfrm6_output+0x65f/0xb50
[ ] xfrm6_output+0x106/0x46f
[ ] udp_tunnel6_xmit_skb+0x618/0xbf0 [ip6_udp_tunnel]
[ ] vxlan_xmit_one+0xbc6/0x2c60 [vxlan]
[ ] vxlan_xmit+0x6a0/0x4276 [vxlan]
[ ] dev_hard_start_xmit+0x165/0x820
[ ] __dev_queue_xmit+0x1ff0/0x2b90
[ ] ip_finish_output2+0xd3e/0x1480
[ ] ip_do_fragment+0x182d/0x2210
[ ] ip_output+0x1d0/0x510
[ ] ip_send_skb+0x37/0xa0
[ ] raw_sendmsg+0x1b4c/0x2b80
[ ] sock_sendmsg+0xc0/0x110
This occurred when sending a v4 skb over vxlan6 over ipsec, in which case
skb->protocol == htons(ETH_P_IPV6) while skb->sk->sk_family == AF_INET in
xfrm_local_error(). Then it will go to xfrm6_local_error() where it tries
to get ipv6 info from a ipv4 sk.
This issue was actually fixed by Commit 628e341f31 ("xfrm: make local
error reporting more robust"), but brought back by Commit 844d48746e
("xfrm: choose protocol family by skb protocol").
So to fix it, we should call xfrm6_local_error() only when skb->protocol
is htons(ETH_P_IPV6) and skb->sk->sk_family is AF_INET6.
Fixes: 844d48746e ("xfrm: choose protocol family by skb protocol")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
comparison
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXs+b2wAKCRDj7w1vZxhR
xdZ9AQC9uquqrOAGV8Falzp+Obu1MDp7nu8zrKH35jWt+UtONwEAk8TsnMAq7y18
Bi4cAke59vX/YLiMaN8EamJs67FGsw0=
=zcXf
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2020-05-28' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Two ingenic fixes, one for a wrong cast, the other for a typo in a
comparison
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200528110944.hanv4qgc6w7whnj3@gilmour.lan
Recent change in virtio_net_hdr_to_skb() broke some packetdrill tests.
When --mss=XXX option is set, packetdrill always provide gso_type & gso_size
for its inbound packets, regardless of packet size.
if (packet->tcp && packet->mss) {
if (packet->ipv4)
gso.gso_type = VIRTIO_NET_HDR_GSO_TCPV4;
else
gso.gso_type = VIRTIO_NET_HDR_GSO_TCPV6;
gso.gso_size = packet->mss;
}
Since many other programs could do the same, relax virtio_net_hdr_to_skb()
to no longer return an error, but instead ignore gso settings.
This keeps Willem intent to make sure no malicious packet could
reach gso stack.
Note that TCP stack has a special logic in tcp_set_skb_tso_segs()
to clear gso_size for small packets.
Fixes: 6dd912f826 ("net: check untrusted gso_size at kernel entry")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure SCTP_ADDR_{MADE_PRIM,ADDED} are sent only for associations
that have been established.
These events are described in rfc6458#section-6.1
SCTP_PEER_ADDR_CHANGE:
This tag indicates that an address that is
part of an existing association has experienced a change of
state (e.g., a failure or return to service of the reachability
of an endpoint via a specific transport address).
Signed-off-by: Jonas Falkevik <jonas.falkevik@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the copy_process() routine called by _do_fork(), failure to allocate
a PID (or further along in the function) will trigger an invocation to
exit_thread(). This is done to clean up from an earlier call to
copy_thread_tls(). Naturally, the child task is passed into exit_thread(),
however during the process, io_bitmap_exit() nullifies the parent's
io_bitmap rather than the child's.
As copy_thread_tls() has been called ahead of the failure, the reference
count on the calling thread's io_bitmap is incremented as we would expect.
However, io_bitmap_exit() doesn't accept any arguments, and thus assumes
it should trash the current thread's io_bitmap reference rather than the
child's. This is pretty sneaky in practice, because in all instances but
this one, exit_thread() is called with respect to the current task and
everything works out.
A determined attacker can issue an appropriate ioctl (i.e. KDENABIO) to
get a bitmap allocated, and force a clone3() syscall to fail by passing
in a zeroed clone_args structure. The kernel handles the erroneous struct
and the buggy code path is followed, and even though the parent's reference
to the io_bitmap is trashed, the child still holds a reference and thus
the structure will never be freed.
Fix this by tweaking io_bitmap_exit() and its subroutines to accept a
task_struct argument which to operate on.
Fixes: ea5f1cd7ab ("x86/ioperm: Remove bitmap if all permissions dropped")
Signed-off-by: Jay Lang <jaytlang@mit.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable#@vger.kernel.org
Link: https://lkml.kernel.org/r/20200524162742.253727-1-jaytlang@mit.edu
This reverts commit c58c1f8343.
io_uring does do the right thing for this case, and we're still returning
-EAGAIN to userspace for the cases we don't support. Revert this change
to avoid doing endless spins of resubmits.
Cc: stable@vger.kernel.org # v5.6
Reported-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Even though the x86 ticket spinlock code has been removed with
cfd8983f03 ("x86, locking/spinlocks: Remove ticket (spin)lock implementation")
a while ago, there are still some ticket spinlock specific macros and
types left in the asm/spinlock_types.h header file that are no longer
used. Remove those as well to avoid confusion.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200526122014.25241-1-longman@redhat.com
KMSAN reported uninitialized data being written to disk when dumping
core. As a result, several kilobytes of kmalloc memory may be written
to the core file and then read by a non-privileged user.
Reported-by: sam <sunhaoyl@outlook.com>
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200419100848.63472-1-glider@google.com
Link: https://github.com/google/kmsan/issues/76
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace superfluous VM_BUG_ON() with comment about correct usage.
Technically reverts commit 1d148e218a ("mm: add VM_BUG_ON_PAGE() to
page_mapcount()"), but context lines have changed.
Function isolate_migratepages_block() runs some checks out of lru_lock
when choose pages for migration. After checking PageLRU() it checks
extra page references by comparing page_count() and page_mapcount().
Between these two checks page could be removed from lru, freed and taken
by slab.
As a result this race triggers VM_BUG_ON(PageSlab()) in page_mapcount().
Race window is tiny. For certain workload this happens around once a
year.
page:ffffea0105ca9380 count:1 mapcount:0 mapping:ffff88ff7712c180 index:0x0 compound_mapcount: 0
flags: 0x500000000008100(slab|head)
raw: 0500000000008100 dead000000000100 dead000000000200 ffff88ff7712c180
raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000
page dumped because: VM_BUG_ON_PAGE(PageSlab(page))
------------[ cut here ]------------
kernel BUG at ./include/linux/mm.h:628!
invalid opcode: 0000 [#1] SMP NOPTI
CPU: 77 PID: 504 Comm: kcompactd1 Tainted: G W 4.19.109-27 #1
Hardware name: Yandex T175-N41-Y3N/MY81-EX0-Y3N, BIOS R05 06/20/2019
RIP: 0010:isolate_migratepages_block+0x986/0x9b0
The code in isolate_migratepages_block() was added in commit
119d6d59dc ("mm, compaction: avoid isolating pinned pages") before
adding VM_BUG_ON into page_mapcount().
This race has been predicted in 2015 by Vlastimil Babka (see link
below).
[akpm@linux-foundation.org: comment tweaks, per Hugh]
Fixes: 1d148e218a ("mm: add VM_BUG_ON_PAGE() to page_mapcount()")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/159032779896.957378.7852761411265662220.stgit@buzz
Link: https://lore.kernel.org/lkml/557710E1.6060103@suse.cz/
Link: https://lore.kernel.org/linux-mm/158937872515.474360.5066096871639561424.stgit@buzz/T/ (v1)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When collapse_file() calls try_to_release_page(), it has already isolated
the page: so if releasing buffers happens to fail (as it sometimes does),
remember to putback_lru_page(): otherwise that page is left unreclaimable
and unfreeable, and the file extent uncollapsible.
Fixes: 99cb0dbd47 ("mm,thp: add read-only THP support for (non-shmem) FS")
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: <stable@vger.kernel.org> [5.4+]
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.2005231837500.1766@eggly.anvils
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kmemleak reported many leaks while under memory pressue in,
slots = alloc_slots(pool, gfp);
which is referenced by "zhdr" in init_z3fold_page(),
zhdr->slots = slots;
However, "zhdr" could be gone without freeing slots as the later will be
freed separately when the last "handle" off of "handles" array is freed.
It will be within "slots" which is always aligned.
unreferenced object 0xc000000fdadc1040 (size 104):
comm "oom04", pid 140476, jiffies 4295359280 (age 3454.970s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
z3fold_zpool_malloc+0x7b0/0xe10
alloc_slots at mm/z3fold.c:214
(inlined by) init_z3fold_page at mm/z3fold.c:412
(inlined by) z3fold_alloc at mm/z3fold.c:1161
(inlined by) z3fold_zpool_malloc at mm/z3fold.c:1735
zpool_malloc+0x34/0x50
zswap_frontswap_store+0x60c/0xda0
zswap_frontswap_store at mm/zswap.c:1093
__frontswap_store+0x128/0x330
swap_writepage+0x58/0x110
pageout+0x16c/0xa40
shrink_page_list+0x1ac8/0x25c0
shrink_inactive_list+0x270/0x730
shrink_lruvec+0x444/0xf30
shrink_node+0x2a4/0x9c0
do_try_to_free_pages+0x158/0x640
try_to_free_pages+0x1bc/0x5f0
__alloc_pages_slowpath.constprop.60+0x4dc/0x15a0
__alloc_pages_nodemask+0x520/0x650
alloc_pages_vma+0xc0/0x420
handle_mm_fault+0x1174/0x1bf0
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vitaly Wool <vitaly.wool@konsulko.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: http://lkml.kernel.org/r/20200522220052.2225-1-cai@lca.pw
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intermediate result of the old term (4UL * 1024 * 1024 * 1024) is
4 294 967 296 or 0x100000000 which is no problem on 64 bit systems.
The patch does not change the later overall result of 0x100000 for
MAX_DMA32_PFN (after it has been shifted by PAGE_SHIFT). The new
calculation yields the same result, but does not require 64 bit
arithmetic.
On 32 bit systems the old calculation suffers from an arithmetic
overflow in that intermediate term in braces: 4UL aka unsigned long int
is 4 byte wide and an arithmetic overflow happens (the 0x100000000 does
not fit in 4 bytes), the in braces result is truncated to zero, the
following right shift does not alter that, so MAX_DMA32_PFN evaluates to
0 on 32 bit systems.
That wrong value is a problem in a comparision against MAX_DMA32_PFN in
the init code for swiotlb in pci_swiotlb_detect_4gb() to decide if
swiotlb should be active. That comparison yields the opposite result,
when compiling on 32 bit systems.
This was not possible before
1b7e03ef75 ("x86, NUMA: Enable emulation on 32bit too")
when that MAX_DMA32_PFN was first made visible to x86_32 (and which
landed in v3.0).
In practice this wasn't a problem, unless CONFIG_SWIOTLB is active on
x86-32.
However if one has set CONFIG_IOMMU_INTEL, since
c5a5dc4cbb ("iommu/vt-d: Don't switch off swiotlb if bounce page is used")
there's a dependency on CONFIG_SWIOTLB, which was not necessarily
active before. That landed in v5.4, where we noticed it in the fli4l
Linux distribution. We have CONFIG_IOMMU_INTEL active on both 32 and 64
bit kernel configs there (I could not find out why, so let's just say
historical reasons).
The effect is at boot time 64 MiB (default size) were allocated for
bounce buffers now, which is a noticeable amount of memory on small
systems like pcengines ALIX 2D3 with 256 MiB memory, which are still
frequently used as home routers.
We noticed this effect when migrating from kernel v4.19 (LTS) to v5.4
(LTS) in fli4l and got that kernel messages for example:
Linux version 5.4.22 (buildroot@buildroot) (gcc version 7.3.0 (Buildroot 2018.02.8)) #1 SMP Mon Nov 26 23:40:00 CET 2018
…
Memory: 183484K/261756K available (4594K kernel code, 393K rwdata, 1660K rodata, 536K init, 456K bss , 78272K reserved, 0K cma-reserved, 0K highmem)
…
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
software IO TLB: mapped [mem 0x0bb78000-0x0fb78000] (64MB)
The initial analysis and the suggested fix was done by user 'sourcejedi'
at stackoverflow and explicitly marked as GPLv2 for inclusion in the
Linux kernel:
https://unix.stackexchange.com/a/520525/50007
The new calculation, which does not suffer from that overflow, is the
same as for arch/mips now as suggested by Robin Murphy.
The fix was tested by fli4l users on round about two dozen different
systems, including both 32 and 64 bit archs, bare metal and virtualized
machines.
[ bp: Massage commit message. ]
Fixes: 1b7e03ef75 ("x86, NUMA: Enable emulation on 32bit too")
Reported-by: Alan Jenkins <alan.christopher.jenkins@gmail.com>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Alexander Dahl <post@lespocky.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: https://unix.stackexchange.com/q/520065/50007
Link: https://web.nettworks.org/bugs/browse/FFL-2560
Link: https://lkml.kernel.org/r/20200526175749.20742-1-post@lespocky.de
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object. Previous
commit "b8eb718348b8" fixed a similar problem.
Fixes: 07699f9a7c ("bonding: add sysfs /slave dir for bond slave devices.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Uninitialized when used in __nf_conntrack_update(), from
Nathan Chancellor.
2) Comparison of unsigned expression in nf_confirm_cthelper().
3) Remove 'const' type qualifier with no effect.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The DISCONTIGMEM support was marked as deprecated in v5.2 and since there
were no complaints about it for almost 5 releases it can be completely
removed.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20200223094322.15206-1-rppt@kernel.org
AMD's next generation of EPYC processors support the MPK (Memory
Protection Keys) feature. Update the dependency and documentation.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/159068199556.26992.17733929401377275140.stgit@naples-babu.amd.com
The commit 0ebeea8ca8 ("bpf: Restrict bpf_probe_read{, str}() only
to archs where they work") caused that bpf_probe_read{, str}() functions
were not longer available on architectures where the same logical address
might have different content in kernel and user memory mapping. These
architectures should use probe_read_{user,kernel}_str helpers.
For backward compatibility, the problematic functions are still available
on architectures where the user and kernel address spaces are not
overlapping. This is defined CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE.
At the moment, these backward compatible functions are enabled only on x86_64,
arm, and arm64. Let's do it also on powerpc that has the non overlapping
address space as well.
Fixes: 0ebeea8ca8 ("bpf: Restrict bpf_probe_read{, str}() only to archs where they work")
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/lkml/20200527122844.19524-1-pmladek@suse.com
Baikal-T1 SoC provides an embedded process, voltage and temperature
sensor to monitor an internal SoC environment (chip temperature, supply
voltage and process monitor) and on time detect critical situations,
which may cause the system instability and even damages. The IP-block
is based on the Analog Bits PVT sensor, but is equipped with a
dedicated control wrapper, which provides a MMIO registers-based access
to the sensor core functionality (APB3-bus based) and exposes an
additional functions like thresholds/data ready interrupts, its status
and masks, measurements timeout. All of these is used to create a hwmon
driver being added to the kernel by this commit.
The driver implements support for the hardware monitoring capabilities
of Baikal-T1 process, voltage and temperature sensors. PVT IP-core
consists of one temperature and four voltage sensors, each of which is
implemented as a dedicated hwmon channel config.
The driver can optionally provide the hwmon alarms for each sensor the
PVT controller supports. The alarms functionality is made compile-time
configurable due to the hardware interface implementation peculiarity,
which is connected with an ability to convert data from only one sensor
at a time. Additional limitation is that the controller performs the
thresholds checking synchronously with the data conversion procedure.
Due to these limitations in order to have the hwmon alarms
automatically detected the driver code must switch from one sensor to
another, read converted data and manually check the threshold status
bits. Depending on the measurements timeout settings this design may
cause additional burden on the system performance. By default if the
alarms kernel config is disabled the data conversion is performed by
the driver on demand when read operation is requested via corresponding
_input-file.
Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For hwmon drivers using the hwmon_device_register_with_info() API, it
is desirable to have a generic notification mechanism available. This
mechanism can be used to notify userspace as well as the thermal
subsystem if the driver experiences any events, such as warning or
critical alarms.
Implement hwmon_notify_event() to provide this mechanism. The function
generates a sysfs event and a udev event. If the device is registered
with the thermal subsystem and the event is associated with a temperature
sensor, also notify the thermal subsystem that a thermal event occurred.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Baikal-T1 SoC is equipped with an embedded process, voltage and
temperature sensor to monitor the chip internal environment like
temperature, supply voltage and transistors performance.
This bindings describes the external Baikal-T1 PVT control interfaces
like MMIO registers space, interrupt request number and clocks source.
These are then used by the corresponding hwmon device driver to
implement the sysfs files-based access to the sensors functionality.
Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is ecspi ERR009165 on i.mx6/7 soc family, which cause FIFO
transfer to be send twice in DMA mode. Please get more information from:
https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf. The workaround is adding
new sdma ram script which works in XCH mode as PIO inside sdma instead
of SMC mode, meanwhile, 'TX_THRESHOLD' should be 0. The issue should be
exist on all legacy i.mx6/7 soc family before i.mx6ul.
NXP fix this design issue from i.mx6ul, so newer chips including i.mx6ul/
6ull/6sll do not need this workaroud anymore. All other i.mx6/7/8 chips
still need this workaroud. This patch set add new 'fsl,imx6ul-ecspi'
for ecspi driver and 'ecspi_fixed' in sdma driver to choose if need errata
or not.
The first two reverted patches should be the same issue, though, it
seems 'fixed' by changing to other shp script. Hope Sean or Sascha could
have the chance to test this patch set if could fix their issues.
Besides, enable sdma support for i.mx8mm/8mq and fix ecspi1 not work
on i.mx8mm because the event id is zero.
PS:
Please get sdma firmware from below linux-firmware and copy it to your
local rootfs /lib/firmware/imx/sdma.
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/imx/sdma
v2:
1.Add commit log for reverted patches.
2.Add comment for 'ecspi_fixed' in sdma driver.
3.Add 'fsl,imx6sll-ecspi' compatible instead of 'fsl,imx6ul-ecspi'
rather than remove.
v3:
1.Confirm with design team make sure ERR009165 fixed on i.mx6ul/i.mx6ull
/i.mx6sll, not fixed on i.mx8m/8mm and other i.mx6/7 legacy chips.
Correct dts related dts patch in v2.
2.Clean eratta information in binding doc and new 'tx_glitch_fixed' flag
in spi-imx driver to state ERR009165 fixed or not.
3.Enlarge burst size to fifo size for tx since tx_wml set to 0 in the
errata workaroud, thus improve performance as possible.
v4:
1.Add Ack tag from Mark and Vinod
2.Remove checking 'event_id1' zero as 'event_id0'.
v5:
1.Add the last patch for compatible with the current uart driver which
using rom script, so both uart ram script and rom script supported
in latest firmware, by default uart rom script used. UART driver
will be broken without this patch.
v6:
1.Resend after rebase the latest next branch.
2.Remove below No.13~No.15 patches of v5 because they were mergered.
ARM: dts: imx6ul: add dma support on ecspi
ARM: dts: imx6sll: correct sdma compatible
arm64: defconfig: Enable SDMA on i.mx8mq/8mm
3.Revert "dmaengine: imx-sdma: fix context cache" since
'context_loaded' removed.
v7:
1.Put the last patch 13/13 'Revert "dmaengine: imx-sdma: fix context
cache"' to the ahead of 03/13 'Revert "dmaengine: imx-sdma: refine
to load context only once" so that no building waring during comes out
during bisect.
2.Address Sascha's comments, including eliminating any i.mx6sx in this
series, adding new 'is_imx6ul_ecspi()' instead imx in imx51 and taking
care SMC bit for PIO.
3.Add back missing 'Reviewed-by' tag on 08/15(v5):09/13(v7)
'spi: imx: add new i.mx6ul compatible name in binding doc'
v8:
1.remove 0003-Revert-dmaengine-imx-sdma-fix-context-cache.patch and merge
it into 04/13 of v7
2.add 0005-spi-imx-fallback-to-PIO-if-dma-setup-failure.patch for no any
ecspi function broken even if sdma firmware not updated.
3.merge 'tx.dst_maxburst' changes in the two continous patches into one
patch to avoid confusion.
4.fix typo 'duplicated'.
Robin Gong (13):
Revert "ARM: dts: imx6q: Use correct SDMA script for SPI5 core"
Revert "ARM: dts: imx6: Use correct SDMA script for SPI cores"
Revert "dmaengine: imx-sdma: refine to load context only once"
dmaengine: imx-sdma: remove duplicated sdma_load_context
spi: imx: fallback to PIO if dma setup failure
dmaengine: imx-sdma: add mcu_2_ecspi script
spi: imx: fix ERR009165
spi: imx: remove ERR009165 workaround on i.mx6ul
spi: imx: add new i.mx6ul compatible name in binding doc
dmaengine: imx-sdma: remove ERR009165 on i.mx6ul
dma: imx-sdma: add i.mx6ul compatible name
dmaengine: imx-sdma: fix ecspi1 rx dma not work on i.mx8mm
dmaengine: imx-sdma: add uart rom script
.../devicetree/bindings/dma/fsl-imx-sdma.txt | 1 +
.../devicetree/bindings/spi/fsl-imx-cspi.txt | 1 +
arch/arm/boot/dts/imx6q.dtsi | 2 +-
arch/arm/boot/dts/imx6qdl.dtsi | 8 +-
drivers/dma/imx-sdma.c | 67 ++++++++++------
drivers/spi/spi-imx.c | 92 +++++++++++++++++++---
include/linux/platform_data/dma-imx-sdma.h | 8 +-
7 files changed, 135 insertions(+), 44 deletions(-)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523124758.28604-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523122909.25247-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523125704.30300-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Fallback to PIO in case dma setup failed. For example, sdma firmware not
updated but ERR009165 workaroud added in kernel.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/1590006865-20900-6-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit
987053a300 ("efi/x86: Move command-line initrd loading to efi_main")
moved the command-line initrd loading into efi_main(), with a check
to ensure that it was attempted only if the EFI stub was booted via
efi_pe_entry rather than the EFI handover entry.
However, in the case where it was booted via handover entry, and thus an
initrd may have already been loaded by the bootloader, it then wrote 0
for the initrd address and size, removing any existing initrd.
Fix this by checking if size is positive before setting the fields in
the bootparams structure.
Fixes: 987053a300 ("efi/x86: Move command-line initrd loading to efi_main")
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lkml.kernel.org/r/20200527232602.21596-1-nivedita@alum.mit.edu
If boot_secondary() was successful, and cpu_online() was an error in
__cpu_up(), -EIO was returned, but 0 is returned by commit d22b115cbf
("arm64/kernel: Simplify __cpu_up() by bailing out early").
Therefore, bringup_wait_for_ap() causes the primary core to wait for a
long time, which may cause boot failure.
This commit sets -EIO to return code under the same conditions.
Fixes: d22b115cbf ("arm64/kernel: Simplify __cpu_up() by bailing out early")
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Tested-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Acked-by: Will Deacon <will@kernel.org>
Cc: Gavin Shan <gshan@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20200527233457.2531118-1-nobuhiro1.iwamatsu@toshiba.co.jp
[catalin.marinas@arm.com: return -EIO at the end of the function]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Current RCU hard relies on smp_call_function() callbacks running from
interrupt context. A pending optimization is going to break that, it
will allow idle CPUs to run the callbacks from the idle loop. This
avoids raising the IPI on the requesting CPU and avoids handling an
exception on the receiving CPU.
Change rcu_is_cpu_rrupt_from_idle() to also accept task context,
provided it is the idle task.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Link: https://lore.kernel.org/r/20200527171236.GC706495@hirez.programming.kicks-ass.net
The zcomp driver uses per-CPU compression. The per-CPU data pointer is
acquired with get_cpu_ptr() which implicitly disables preemption.
It allocates memory inside the preempt disabled region which conflicts
with the PREEMPT_RT semantics.
Replace the implicit preemption control with an explicit local lock.
This allows RT kernels to substitute it with a real per CPU lock, which
serializes the access but keeps the code section preemptible. On non RT
kernels this maps to preempt_disable() as before, i.e. no functional
change.
[bigeasy: Use local_lock(), description, drop reordering]
Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200527201119.1692513-8-bigeasy@linutronix.de
zcomp::stream is a per-CPU pointer, pointing to struct zcomp_strm
which contains two pointers. Having struct zcomp_strm allocated
directly as per-CPU memory would avoid one additional memory
allocation and a pointer dereference. This also simplifies the
addition of a local_lock to struct zcomp_strm.
Allocate zcomp::stream directly as per-CPU memory.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200527201119.1692513-7-bigeasy@linutronix.de
send_msg() disables preemption to avoid out-of-order messages. As the
code inside the preempt disabled section acquires regular spinlocks,
which are converted to 'sleeping' spinlocks on a PREEMPT_RT kernel and
eventually calls into a memory allocator, this conflicts with the RT
semantics.
Convert it to a local_lock which allows RT kernels to substitute them with
a real per CPU lock. On non RT kernels this maps to preempt_disable() as
before. No functional change.
[bigeasy: Patch description]
Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200527201119.1692513-6-bigeasy@linutronix.de
The squashfs multi CPU decompressor makes use of get_cpu_ptr() to
acquire a pointer to per-CPU data. get_cpu_ptr() implicitly disables
preemption which serializes the access to the per-CPU data.
But decompression can take quite some time depending on the size. The
observed preempt disabled times in real world scenarios went up to 8ms,
causing massive wakeup latencies. This happens on all CPUs as the
decompression is fully parallelized.
Replace the implicit preemption control with an explicit local lock.
This allows RT kernels to substitute it with a real per CPU lock, which
serializes the access but keeps the code section preemptible. On non RT
kernels this maps to preempt_disable() as before, i.e. no functional
change.
[ bigeasy: Use local_lock(), patch description]
Reported-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200527201119.1692513-5-bigeasy@linutronix.de
The various struct pagevec per CPU variables are protected by disabling
either preemption or interrupts across the critical sections. Inside
these sections spinlocks have to be acquired.
These spinlocks are regular spinlock_t types which are converted to
"sleeping" spinlocks on PREEMPT_RT enabled kernels. Obviously sleeping
locks cannot be acquired in preemption or interrupt disabled sections.
local locks provide a trivial way to substitute preempt and interrupt
disable instances. On a non PREEMPT_RT enabled kernel local_lock() maps
to preempt_disable() and local_lock_irq() to local_irq_disable().
Create lru_rotate_pvecs containing the pagevec and the locallock.
Create lru_pvecs containing the remaining pagevecs and the locallock.
Add lru_add_drain_cpu_zone() which is used from compact_zone() to avoid
exporting the pvec structure.
Change the relevant call sites to acquire these locks instead of using
preempt_disable() / get_cpu() / get_cpu_var() and local_irq_disable() /
local_irq_save().
There is neither a functional change nor a change in the generated
binary code for non PREEMPT_RT enabled non-debug kernels.
When lockdep is enabled local locks have lockdep maps embedded. These
allow lockdep to validate the protections, i.e. inappropriate usage of a
preemption only protected sections would result in a lockdep warning
while the same problem would not be noticed with a plain
preempt_disable() based protection.
local locks also improve readability as they provide a named scope for
the protections while preempt/interrupt disable are opaque scopeless.
Finally local locks allow PREEMPT_RT to substitute them with real
locking primitives to ensure the correctness of operation in a fully
preemptible kernel.
[ bigeasy: Adopted to use local_lock ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200527201119.1692513-4-bigeasy@linutronix.de
The radix-tree and idr preload mechanisms use preempt_disable() to protect
the complete operation between xxx_preload() and xxx_preload_end().
As the code inside the preempt disabled section acquires regular spinlocks,
which are converted to 'sleeping' spinlocks on a PREEMPT_RT kernel and
eventually calls into a memory allocator, this conflicts with the RT
semantics.
Convert it to a local_lock which allows RT kernels to substitute them with
a real per CPU lock. On non RT kernels this maps to preempt_disable() as
before, but provides also lockdep coverage of the critical region.
No functional change.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200527201119.1692513-3-bigeasy@linutronix.de
preempt_disable() and local_irq_disable/save() are in principle per CPU big
kernel locks. This has several downsides:
- The protection scope is unknown
- Violation of protection rules is hard to detect by instrumentation
- For PREEMPT_RT such sections, unless in low level critical code, can
violate the preemptability constraints.
To address this PREEMPT_RT introduced the concept of local_locks which are
strictly per CPU.
The lock operations map to preempt_disable(), local_irq_disable/save() and
the enabling counterparts on non RT enabled kernels.
If lockdep is enabled local locks gain a lock map which tracks the usage
context. This will catch cases where an area is protected by
preempt_disable() but the access also happens from interrupt context. local
locks have identified quite a few such issues over the years, the most
recent example is:
b7d5dc2107 ("random: add a spinlock_t to struct batched_entropy")
Aside of the lockdep coverage this also improves code readability as it
precisely annotates the protection scope.
PREEMPT_RT substitutes these local locks with 'sleeping' spinlocks to
protect such sections while maintaining preemtability and CPU locality.
local locks can replace:
- preempt_enable()/disable() pairs
- local_irq_disable/enable() pairs
- local_irq_save/restore() pairs
They are also used to replace code which implicitly disables preemption
like:
- get_cpu()/put_cpu()
- get_cpu_var()/put_cpu_var()
with PREEMPT_RT friendly constructs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200527201119.1692513-2-bigeasy@linutronix.de
In order to be compatible with devices of different versions, V1 in the
accelerator driver is now isolated, and other versions are the previous
V2 processing flow.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now, in crypto-engine, if hardware queue is full (-ENOSPC),
requeue request regardless of MAY_BACKLOG flag.
If hardware throws any other error code (like -EIO, -EINVAL,
-ENOMEM, etc.) only MAY_BACKLOG requests are enqueued back into
crypto-engine's queue, since the others can be dropped.
The latter case can be fatal error, so those cannot be recovered from.
For example, in CAAM driver, -EIO is returned in case the job descriptor
is broken, so there is no possibility to fix the job descriptor.
Therefore, these errors might be fatal error, so we shouldn’t
requeue the request. This will just be pass back and forth between
crypto-engine and hardware.
Fixes: 6a89f492f8 ("crypto: engine - support for parallel requests based on retry mechanism")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reported-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch enables AMD Fam17h RAPL support for the Package level metric.
The support is as per AMD Fam17h Model31h (Zen2) and model 00-ffh (Zen1) PPR.
The same output is available via the energy-pkg pseudo event:
$ perf stat -a -I 1000 --per-socket -e power/energy-pkg/
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200527224659.206129-6-eranian@google.com
This patch modifies perf_probe_msr() by allowing passing of
struct perf_msr array where some entries are not populated, i.e.,
they have either an msr address of 0 or no attribute_group pointer.
This helps with certain call paths, e.g., RAPL.
In case the grp is NULL, the default sysfs visibility rule
applies which is to make the group visible. Without the patch,
you would get a kernel crash with a NULL group.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200527224659.206129-5-eranian@google.com
This patch modifies the default visibility of the attribute_group
for each RAPL event. By default if the grp.is_visible field is NULL,
sysfs considers that it must display the attribute group.
If the field is not NULL (callback function), then the return value
of the callback determines the visibility (0 = not visible). The RAPL
attribute groups had the field set to NULL, meaning that unless they
failed the probing from perf_msr_probe(), they would be visible. We want
to avoid having to specify attribute groups that are not supported by the HW
in the rapl_msrs[] array, they don't have an MSR address to begin with.
Therefore, we intialize the visible field of all RAPL attribute groups
to a callback that returns 0. If the RAPL msr goes through probing
and succeeds the is_visible field will be set back to NULL (visible).
If the probing fails the field is set to a callback that return 0 (not visible).
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200527224659.206129-4-eranian@google.com
Linus Walleij