Fix some problems with the use of devm_ functions.
devm_kzalloc: devm_kfree is not needed
devm_ioremap: iounmap should not be used, no free is needed
devm_request_irq: the devm_free_irq is followed by irq_dispose_mapping. I
don't know if it is safe to move the freeing of the irq in this case, so I
have just un-devm'd this function, since the implicit freeing is never
taken advantage of.
In the original code failure of of_address_to_resource jumped to free_mem,
but should have jumped to irq_dispose, since irq_of_parse_and_map has
completed at this point.
In the original code unmap_mem was after irq_dispose, but it should have
been before, again since irq_of_parse_and_map has completed at this point.
One of these problems was found using the following semantic match:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
*x = devm_ioremap(...)
...
iounmap(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlAaIN8ACgkQGkmNcg7/o7gpMgCgtmCJeUrSCc/eVKGy5ik1BPnC
3DAAoLdqCJflwx4mrN48kkXQj9SA4Xko
=Y6yl
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
sh: explicitly include sh_dma.h in setup-sh7722.c
sh: ecovec: care CN5 VBUS if USB host mode
sh: sh7724: fixup renesas_usbhs clock settings
sh: intc: initial irqdomain support.
sh: pfc: Fix up init ordering mess.
serial: sh-sci: fix compilation breakage, when DMA is enabled
dmaengine: shdma: restore partial transfer calculation
sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
sh: Fix up recursive fault in oops with unset TTB.
sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
sh: select the fixed regulator driver on several boards
sh: ecovec: switch MMC power control to regulators
sh: add fixed voltage regulators to se7724
sh: add fixed voltage regulators to sdk7786
sh: add fixed voltage regulators to rsk
sh: add fixed voltage regulators to migor
sh: add fixed voltage regulators to kfr2r09
sh: add fixed voltage regulators to ap325rxa
sh: add fixed voltage regulators to sh7757lcr
sh: add fixed voltage regulators to sh2007
...
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
The recent shdma driver split has mistakenly removed support for partial
DMA transfer size calculation on forced termination. This patch restores
it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for returning the residue for a particular descriptor by
reading the current DMA address for the source or destination side of
the transfer as appropriate, and walking the scatterlist until we find
an entry containing the current DMA address.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use devm_kzalloc, devm_clk_get, devm_request_irq, and devm_request_and_ioremap
to reduce the code and to simplify the error path.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Pull slave-dmaengine update from Vinod Koul:
"This time we have a new dmaengine driver from the tegra folks. Also
we have Guennadi's cleanup of sh drivers which incudes a library for
sh drivers. And the usual odd fixes in bunch of drivers and some nice
cleanup of dw_dmac from Andy."
Fix up conflicts in drivers/mmc/host/sh_mmcif.c
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Cleanup logging messages
mmc: sh_mmcif: switch to the new DMA channel allocation and configuration
dma: sh: provide a migration path for slave drivers to stop using .private
dma: sh: use an integer slave ID to improve API compatibility
dmaengine: shdma: prepare to stop using struct dma_chan::private
sh: remove unused DMA device pointer from SIU platform data
ASoC: siu: don't use DMA device for channel filtering
dmaengine: shdma: (cosmetic) simplify a static function
dmaengine: at_hdmac: add a few const qualifiers
dw_dmac: use 'u32' for LLI structure members, not dma_addr_t
dw_dmac: mark dwc_dump_lli inline
dma: mxs-dma: Export missing symbols from mxs-dma.c
dma: shdma: convert to the shdma base library
ASoC: fsi: prepare for conversion to the shdma base library
usb: renesas_usbhs: prepare for conversion to the shdma base library
ASoC: siu: prepare for conversion to the shdma base library
serial: sh-sci: prepare for conversion to the shdma base library
mmc: sh_mobile_sdhi: prepare for conversion to the shdma base library
mmc: sh_mmcif: remove unneeded struct sh_mmcif_dma, prepare to shdma conversion
dma: shdma: prepare for conversion to the shdma base library
...
Use a more current logging style.
Add pr_fmt to prefix dmaengine: to messages.
Convert printk(KERN_ERR to pr_err(.
Convert embedded function name use to "%s: ", __func__
Align arguments.
Original-patch-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch extends the sh dmaengine driver to support the preferred channel
selection and configuration method, instead of using the "private" field
from struct dma_chan. We add a standard filter function to be used by
slave drivers instead of implementing their own ones, and add support for
the DMA_SLAVE_CONFIG control operation, which must accompany the new
channel selection method. We still support the legacy .private channel
allocation method to cater for a smooth driver migration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
[applied a trvial checkpath fix]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Initially struct shdma_slave has been introduced with the only member - an
unsigned slave ID - to describe common properties of DMA slaves in an
extensible way. However, experience shows, that a slave ID is indeed the
only parameter, needed to identify DMA slaves. This is also, what is used
by the core dmaengine API in struct dma_slave_config. We switch to using
the slave_id directly, instead of passing a pointer to struct shdma_slave
to improve compatibility with the core. We also make the slave_id signed
for easier error checking.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Using struct dma_chan::private is deprecated. To update the shdma driver to
stop using it we first have to eliminate internal runtime uses of it. After
that we will also be able to stop using it for channel configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
dmae_find_slave() needs only the slave_id field from the slave object, no
need to pass the pointer to the object, pass the slave_id directly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This prepares of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/dma/at_hdmac.c: In function 'at_dma_get_driver_data':
drivers/dma/at_hdmac.c:1228: warning: return discards qualifiers from pointer target type
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Use 'u32' for the LLI structure members, which are defined by hardware to be
32-bit. dma_addr_t is much more vague about its actual size.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
mxs-dma.c provides two functions mxs_dma_is_apbh and mxs_dma_is_apbx
which are used at least in mxs-mmc.c. Building mxs-mmc as module
fails due to those two symbols not being exported.
Signed-off-by: Attila Kinali <attila@kinali.ch>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The shdma base library has originally been extracted from the shdma driver,
which now can be converted to actually use it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch extracts code from shdma.c, that does not directly deal with
hardware implementation details and can be re-used with diverse DMA
controller variants, found on SH-based SoCs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The shdma driver is going to be split into multiple files. To make this more
convenient move it to an own directory.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Rename the compatible name and driver name to match with
tegra dts file and as per clock driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
In cyclic mode of DMA, the byte transferred can be more
than the requested size and in this case, calculating
residuals based on the current position of DMA transfer to
bytes requested i.e. bytes required to transfer to reach
bytes requested from current DMA position.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
From Shawn Guo <shawn.guo@linaro.org>, this makes it possible to use
sparse irqs with mach-imx.
* 'imx/sparse-irq' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: enable SPARSE_IRQ for imx platform
ARM: fiq: change FIQ_START to a variable
tty: serial: imx: remove the use of MXC_INTERNAL_IRQS
ARM: imx: remove unneeded mach/irq.h inclusion
i2c: imx: remove unneeded mach/irqs.h inclusion
ARM: imx: add a legacy irqdomain for mx31ads
ARM: imx: add a legacy irqdomain for 3ds_debugboard
ARM: imx: pass gpio than irq number into mxc_expio_init
ARM: imx: leave irq_base of wm8350_platform_data uninitialized
dma: ipu: remove the use of ipu_platform_data
ARM: imx: move irq_domain_add_legacy call into avic driver
ARM: imx: move irq_domain_add_legacy call into tzic driver
gpio/mxc: move irq_domain_add_legacy call into gpio driver
ARM: imx: eliminate macro IRQ_GPIOx()
ARM: imx: eliminate macro IOMUX_TO_IRQ()
ARM: imx: eliminate macro IMX_GPIO_TO_IRQ()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The struct ipu_platform_data is used by platform code to pass
MXC_IPU_IRQ_START to ipu-core driver. We can save it by having
ipu-core driver call irq_alloc_descs to get the irq_base.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Add support for cyclic DMA on sa11x0 platforms. This follows the
discussed behaviour that the callback will be called at some point
after period expires, and may coalesce multiple period expiries into
one callback (due to the tasklet behaviour.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The semantics now implemented are:
- If the cookie has completed successfully, the residue will be zero.
- If the cookie is in progress or the channel is paused, it will be the
number of bytes yet to be transferred. [*]
- If the cookie is queued, it will be the number of bytes in the
descriptor.
* - where this is the number of bytes yet to be transferred to/from
RAM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure all queued descriptors are freed when the channel is released,
ensuring we don't leak memory
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The free function says the pl08x lock should be taken before calling
it. However, the DMA pool allocation/freeing is already properly
locked. The only thing that would need this is pool_ctr, which
happens to be a write-only variable.
Let's get rid of this, and eliminate any need for additional locking
here.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This function is now unnecessary; we can move its internals inline
instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we're converted to use the generic vchan support, we can fix
the residue return from tx_status to be compliant with dmaengine. This
returns the number of bytes remaining for the _specified_ cookie, not
the number of bytes in all pending transfers on the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert to use the virtual dma channel done list, tasklet, and
descriptor freeing.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert to use the virtual dma channel submitted/issued descriptor
lists rather than our own private lists, and use the virtual dma
channel support functions to manage these lists.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initialize the vchan struct, and use the provided spinlock rather than
our own.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert PL08x to use the virt-dma structures.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rework the physical channel allocation mechanism to only allocate
physical channels to virtual channels when they're about to be used.
This eliminates all the complexity with holding channels while
descriptors are being prepared, which is completely unnecessary.
This also brings this driver to a state where the generic virtual DMA
code can be used with this driver, and opens up the possibility of
properly scheduling and prioritorising physical DMA channels to
virtual DMA channels.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than waiting for the tasklet to run, we can start the next
descriptor from interrupt context, as soon as we know that the
previous descriptor has completed.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our behaviour wasn't correct; issue_pending is supposed to be called
before any submitted descriptors are available for processing by the
DMA engine. Split the pend_list in two, one for submitted descriptors
and another list for issued descriptors.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than code the de-queue of the txd several times, move that into
the start_txd function. Rename this to better illustrate what it's
now doing, and call this function when starting a delayed memcpy().
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As we no longer need to pass a descriptor to prep_phy_channel(), we
don't need to keep track of the descriptor which is waiting for a
channel to become available. So let's get rid of it.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the DMA request muxing into the slave prepare code and txd
release/completion code. This means we only hold the DMA request
mux while there are descriptors waiting to be started or are in
progress.
This leaves txd->direction as a write-only variable; remove it.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert PL08x to use a list of completed descriptors rather than
merely relying upon a single pointer. This makes it possible to
schedule the tasklet for other purposes, and makes our behaviour
similar to virt-dma.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Keep track of the number of descriptors currently using a MUX setting
on a per-channel basis. This allows us to know when we have descriptors
queued somewhere which have been assigned a DMA request signal.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the signal handling out of the physical channel structure into
the virtual channel structure, where it should belong as it has more
to do with the virtual channel than the physical one.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split the DMA request mux signal handling from the physical channel
allocation code. The physical channel has very little to do with the
DMA request input which will be used, so these should be two separate
operations.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of the unnecessary checks in dma_slave_config utilizing
the DMA direction. This allows us to move the computation of
cctl to the prepare function.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ignore the direction argument in dma_slave_config, and configure both
directions independently. We still check that the configuration for
the intended direction is valid; this check will eventually be dropped.
This check is just for debugging at present.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Extract the functionality from dma_slave_config to generate the cctl
values for a given bus width and burst size. This allows us to use
this elsewhere in the driver, namely the prepare functions.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the bus and transfer increment selection to the DMA prepare
function rather than the slave configuration function.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As we now store the dma_slave_config in pl08x_dma_chan, we don't need
to store this separately. Use the one in dma_slave_config directly.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a dma_slave_config struct to struct pl08x_dma_chan, and move the
src_addr/dst_addr arguments into this struct. This is a step away
from using the dma_slave_config's direction member.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the driver private data structures into the driver itself, rather
than having them exposed to everyone in a header file.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Try to avoid dereferencing the DMA engine's channel struct in these
platform helpers; instead, pass a pointer to the channel data into
get_signal(), and the returned signal number to put_signal().
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Circular buffers are not handled in this way; we have a separate API
call now to setup circular buffers. So lets not mislead people with
this bool.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The pl08x_driver_data spinlock is only ever initialized. Nothing else
uses it. Let's get rid of it.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
db8196df4 (dmaengine: move drivers to dma_transfer_direction) missed
fixing up the "DMA_NONE" case.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The runtime PM support conflicts with the generic AMBA bus PM, and also
causes a potential deadlock with the PL011 driver as it results in
interrupts being enabled beneath a spinlock.
I don't presently see any solution to this other than by removing the
runtime PM support entirely from the DMA engine driver. Alternative
suggestions welcome.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for cyclic DMA's periodic callbacks. Drivers are expected
to call vchan_cyclic_callback() when a period has completed, which will
schedule the tasklet to make the callback into the driver.
As callbacks are made from tasklet context, it is important to realise
that we don't guarantee a callback for each completed period, but for
N completed periods where N may be greater than one.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a function to find a descriptor within the depths of the
virtualized DMA channel support. Needed for tx_status functionality.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split the virtual slave channel DMA support from the sa11x0 driver so
this code can be shared with other slave DMA engine drivers.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tegra's APB DMA driver support the cyclic mode of data
transfer and hence setting the DMA_CYCLIC caps for dma
channels.
This is require when generic sound dmaengine pcm driver
request for dma channel with CYCLIC capability.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The sound dmaengine pcm driver uses the dma in cyclic mode and
it does not ack the transfer descriptor after transfer stops.
This may lead to hold that desc in chip's dma driver and does
not allow to reuse/free that descriptors. Hence not enabling
flag DMA_CTRL_ACK when dma runs in cyclic mode.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Use clk_prepare/clk_unprepare as required by the generic clk framework.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Use the sg_dma_address() to get the segment buffer address for
DMA transfer in place of sg_phys() which returns the physical
address of an sg entry.
The sg_dma_address() returns the correct buffer memory address
for DMA transfer.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Pull slave-dmaengine fixes from Vinod Koul:
"A few fixes in pl330 and imx-sdma drivers."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
DMA: PL330: Fix racy mutex unlock
DMA: PL330: Add missing static storage class specifier
dma: imx-sdma: buf_tail should be initialize in prepare function
dmaengine: pl330: dont complete descriptor for cyclic dma
This piece of code is used often. Make it as a separate function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
We usually have more than one DMA device. Thus, the probe function should serve
for all of them in case when the driver is built as a module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There were three places where such function is used. We still avoid to use
native fls() because in one case it requires to use 64bit version which is
suboptimal in our case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Just to be sure we are in known state we disable the BLOCK interupts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The dw_dma_off call needs to have the all_chan_mask calculated. So, done this
calculations before the call. Moreover, remove duplicate code that masks the
DMA interrupts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
In case the first descriptor we found is available, the counter still remains 0
value which is wrong. This patch fixes the counter behaviour.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There is three places where values of the most significant registers were
printed. Make such piece of code as separate function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
dma_addr_t is sometimes 32 bit and sometimes 64. We normally cast them to
unsigned long long for printk().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for two-channel dma under dmaengine
support: mmp-adma and pxa910-squ
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Allocate memory, region, remap and irq for device state using
devm_* helpers to simplify memory accounting.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
pl330_update() stores a pointer to the thrd->req that finished, which
contains a pointer to the corresponding pl330_req. This is done with
the pl330_lock held. Then, it iterates through the req_done list,
calling the callback for each of the requests that are done. The
problem is that the driver releases the lock before calling the
callback for each of the callbacks. pl330_submit_req() running in
another processor can then acquire the lock and insert another request
in one of the thrd->req that hasn't been processed yet, replacing the
pointer to pl330_req there. When the callback returns in
pl330_update() and the next rqdone is popped from the list, it
dereferences the pl330_req pointer to the just scheduled pl330_req,
instead of the one that has finished, calling pl330 with the wrong r.
This patch fixes this by storing the pointer to pl330_req directly in
the list.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Not all Atmel SoCs were pointed out in header comment which was bringing
confusion. Remove the truncated list of supported devices, replace by the
only one that is not supported.
Reported-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add dmaengine based NVIDIA's Tegra APB DMA driver.
This driver support the slave mode of data transfer from
peripheral to memory and vice versa.
The driver supports for the cyclic and non-cyclic mode
of data transfer.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Fixes the following sparse warning:
drivers/dma/pl330.c:2542:5: warning: symbol 'add_desc' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This fix audio underrun issue. When SNDRV_PCM_TRIGGER_STOP
and SNDRV_PCM_TRIGGER_START, it calls prepare again. buf_tail
should be reset to zero.
So move buf_tail initialization into prepare function.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Commit eab2158558 ("dmaengine: pl330: dont complete descriptor for
cyclic dma") wrongly completes descriptor for cyclic dma, hence following
BUG_ON is still hit with cyclic DMA operations.
kernel BUG at drivers/dma/dmaengine.h:53!
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPuevXAAoJEIwa5zzehBx3D8YQAKfoY3TFjJ9KmJgk69/pc7cf
Of0rvX+35NezGFljIyRdspz+DsV+vhJravwdVxOagRKvVBOb9qnZIXnl3gkLnTw4
dCVMFMqCwXhBeXlXCzHSeRmt2+4/fmJnr7jr4xh9omOAJ9BZv5ftmKNW4zP5wr1L
+9HBwzkxlVisR4NCz2q66YBjsV2dXA3dv2hZxEFkUdQFYJGqZoUXLYHF9yno20i3
knKNXEyAFYFUKHiFVBQJ1tYGmZlaIjw14g+GTqzZay2Pi/HjUXfrPd0VwNkBzZf/
H1N3/cf4GJ2+K/zYqh+H/Xjf/Fjkp1dFNhlUQ7+l5Jwbu7C1B2euvwTO4OaqrfdD
7eqG3+uIKhPO2Z8ZySLFgx4ghybtwgZrAwOjsa+ymTugqPbiWYB/zZR1iWu5DMk/
TnNb6P3ciP+WMpoMFh1kXRc/eCCCHtuQ0rLRxizSX6HIpxWvjYFNLH7L3wS+KtlB
7vsS764d1JFW318bsdBi+V/LWRVXeSWWetTzdzDcM/Syz3ZqfPy7e3Ge6qx0lvYe
5ojgzKwVqpJenZdt91UC16cMXNqDTzmZObz6LOCmVm1mB5kYSgEHYxAQQvuGFjXT
28kGyBQNsBboJGaYh2O/CTsVXnHnaPXrtDDWMDacWNwwPYnnA2L8lUNfAg1DgA1j
Z6CO8Knfct01EpQLtybK
=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
Pull slave-dmaengine updates from Vinod Koul:
"Nothing exciting this time, odd fixes in a bunch of drivers"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: at_hdmac: take maxburst from slave configuration
dmaengine: at_hdmac: remove ATC_DEFAULT_CTRLA constant
dmaengine: at_hdmac: remove some at_dma_slave comments
dma: imx-sdma: make channel0 operations atomic
dmaengine: Fixup dmaengine_prep_slave_single() to be actually useful
dmaengine: Use dma_sg_len(sg) instead of sg->length
dmaengine: Use sg_dma_address instead of sg_phys
DMA: PL330: Remove duplicate header file inclusion
dma: imx-sdma: keep the callbacks invoked in the tasklet
dmaengine: dw_dma: add Device Tree probing capability
dmaengine: dw_dmac: Add clk_{un}prepare() support
dma/amba-pl08x: add support for the Nomadik variant
dma/amba-pl08x: check for terminal count status only
Julia Lawall