This patch contain several fixes for the BCM84833. This PHY is still not in bnx2x production, hence this patch can be considered as enhancement.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put Warpcore in low power mode in case of fan failure to reduce heat.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem when new traffic class is created with 0% BW, the ETS is not conforming.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change BRB to work in per class guaranteed mode and handle cases for BW 0%.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where CONFIG_PSTORE=n, the function efi_pstore_read() doesn't
have the correct list of parameters. This patch provides a definition
of efi_pstore_read() with 'char **buf' added to fix this warning:
"drivers/firmware/efivars.c:609: warning: initialization from".
problem introduced in commit f6f8285132
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Don't over-schedule QSFP work on driver initialization. It could end
up being run simultaneously on two different CPUs resulting in bad
EEPROM reads. In combination with setting the physical IB link state
prior to the IBC being brought out of reset, this can cause the link
state machine to start training early with wrong settings.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix logic so that we don't retry with MPAv1 once we have done that
already. Otherwise, we end up retrying with MPAv1 even when its not
needed on getting peer aborts - and this could lead to kernel panic.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix another place in the code where logic dealing with the t4_cqe was
using the wrong QID. This fixes the counting logic so that it tests
against the SQ QID instead of the RQ QID when counting RCQES.
Signed-off by: Jonathan Lallinger <jonathan@ogc.us>
Signed-off by: Steve Wise <swise@ogc.us>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add more data when inconsistencies occur in the AGG state machine.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not sure it is the best way to do it, but many times we want to know what the
configuration options were enabled for the compiled driver.
Let's just log the options during load time; so there were be no confusion.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the uCode hasn't been released (yet?),
warn only if using older than API 4, but load
anything up to API 6.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes handling the calibration data more generic
and no longer requires updating IWL_CALIB_MAX when a
new uCode comes with more calibration packets. Since
we just copy the data back, there's also no need for
understanding which calibration we received -- we can
just reflect it back to the runtime uCode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The init microcode knows very well which calibrations
are required and sends us results for those that are.
Consequently, we can just send all of those to the RT
uCode again.
The problem with having the driver know about this is
that it is a uCode feature, not a hardware feature so
the config is completely unsuitable.
The only thing we need to check is whether the device
needs crystal calibration or not, add a new parameter
to the configuration for that.
This makes new uCode work on 6000 series devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create new testmode commands to suppot indirect access
of peripheral register.
- IWL_TM_CMD_APP2DEV_INDIRECT_REG_READ32
- IWL_TM_CMD_APP2DEV_INDIRECT_REG_WRITE32
Meanwhile, add affix "DIRECT" into original register access
commands for better discrimination with new commands.
- IWL_TM_CMD_APP2DEV_DIRECT_REG_READ32
- IWL_TM_CMD_APP2DEV_DIRECT_REG_WRITE32
- IWL_TM_CMD_APP2DEV_DIRECT_REG_WRITE8
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Optimize ath5k_cw_validate by using the classic (X & (X - 1)) == 0
check to see if a number is power of 2.
v2: Use functions from log2.h instead
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to documentation higher DCUs have higher priority and should
be used for beacons and CAB traffic. More specifically DCU 9 should be
used for beacons and DCU 8 for CAB traffic, I assumed DCU 7 should be
OK for UAPSD traffic.
Note that DCU 8 and 9 are special because they can only be mapped to a single
QCU each but since we use a 1:1 mapping between QCUs and DCUs anyway we don't
have to change much.
P.S. I also did a few related cleanups on qcu.c and ath5k.h
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MRR support and 2GHz radio override belong in ah_capabilities and we
should use them (e.g. so far we used to set mrr descriptor without
checking if MRR support is enabled + we checked for MRR support 2
times, one by trying to set up an MRR descriptor and another one based
on MAC version).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a module parameter to disable hw rf kill switch (GPIO interrupt) because
in some cases when the card doesn't come with the laptop, EEPROM configuration
doesn't match laptop's configuration and rf kill interrupt always fires up and
disables hw. I thought of moving this to debugfs and make it per-card but
this way it's easier for users and distros to handle.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no short calibration on AR5210, make sure we treat it always
as full calibration.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No functional changes
Add kernel doc for all ath5k_hw_* functions and strcucts. Also do some cleanup,
rename ath5k_hw_init_beacon to ath5k_hw_init_beacon_timers, remove an unused
variable from ath5k_hw_pcu_init and a few obsolete macros, mostly related to XR.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use usleep_range where possible to reduce busy waits
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noise floor calibration does not interfere with traffic and should run more
often as part of our "short calibration". The full calibration is not the
noise floor calibration but the AGC + Gain_F (on RF5111 and RF5112) calibration
and should run less often because it does interfere with traffic.
So
Short calibration -> I/Q & NF Calibration
Long calibration -> Short + AGC + Gain_F
This patch was for some time on my pub/ dir on www.kernel.org and has been tested
by a few people and me. I think it's O.K. to go in.
I also changed ah_calibration to ah_iq_cal_needed to make more sense.
v2 Use a workqueue instead of a tasklet for calibration
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No functional changes, just a few comments/documentation/cleanup
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add TXNOFRM to INT_TX_ALL since it's a TX interrupt too.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since card has 12 tx queues and we want to keep track of the interrupts
per queue we can't fit all these interrupt bits on a single register.
So we have 5 registers, the primary interrupt status register (PISR) and
the 4 secondary interupt status registers (SISRs).
In order to be able to read them all at once (atomic operation) Atheros
introduced the Read-And-Clear registers to make things easier. So when
reading RAC_PISR register, hw does a read on PISR and all SISRs, returns
the value of PISR, copies all SISR values to their shadow copies (RAC_SISRx)
and clears PISR and SISRs. This saves us from reading PISR/SISRs in a sequence.
So far we 've used this approach and MadWiFi/Windows driver etc also used it
for years.
It turns out this operation is not atomic after all (at least not on all cards)
That means it's possible to loose some interrupts because they came after the
copy step and hw cleared them on the clean step !
That's probably the reason we got missed beacons, got stuck queues etc and
couldn't figure out what was going on.
With this patch we switch from RaC operation to an alternative method (that
makes more sense IMHO anyway, I just chose to be on the safe side so far).
Instead of reading RAC registers, we read the normal PISR/SISR registers and
clear any bits we got by writing them back on the register. This will clear only
the bits we got on our read step and leave any new bits unaffected (at least
that's what docs say). So if any new interrupts come up we won't miss it.
I've tested this with an AR5213 and an AR2425 and it seems O.K.
Many thanks to Adrian Chadd for debuging this and reviewing the patch !
v2: Make sure we don't clear PISR bits that map to SISR generated interrupts
(added a comment on the code for this)
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Luciano Coelho <coelho@ti.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously BlockAcks were always dropped by the rt2800 hardware while
BlockAckReqs were always accepted. However, both are only useful on
monitor interfaces at the moment and both are control frames. So
pass them up when mac80211 sets FIF_CONTROL.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent discussion regarding an incorrect return of IRQ_HANDLED
from rt2800pci caused me to look at this PCI interrupt routine. I
discovered that changes were needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change parameter to device pointer for bus layer interface function
brcmf_sdbrcm_bus_stop. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_bus_get_device is no longer necessary. Use dongle device pointer
saved in brcmf_pub directly. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change parameter to device pointer for bus layer interface function
brcmf_sdbrcm_bus_init. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change parameter to device pointer for bus layer interface function
brcmf_sdbrcm_bus_txdata. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change paramter to device pointer for bus layer interface function
brcmf_sdbrcm_bus_txctl. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_sdbrcm_bus_rxctl acts as an interface function of bus layer.
Change parameter from struct brcmf_sdio to device pointer in order to
provide a more compatible interface for different bus layers. This
is part of the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
structure brcmf_pub contains context for generic layer and should
not be used in brcmf_sdbrcm_bus_watchdog. This patch is part of
fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
busstate keeps track of the bus (USB/SDIO) status and is used by
both generic layer and bus layer. Move it to brcmf_bus helps to clean
up the interface. This patch is part of fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct brcmf_bus will contain function porinter, bus specific
private structure pointer and interface context of generic layer
and bus layer. It will be the only shared structure between generic
and bus layer. This patch is part of fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename sdio bus structure brcmf_bus to brcmf_sdio for preparation
of USB bus support. This patch is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bus_no, slot, func and bustype are no longer needed by brcmf_sdbrcm_probe.
This patch removes them.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_c_init only init brcmf_msg_level used for debug. It's no longer
needed as brcmf_msg_level doesn't cause trouble to multiple instances.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the fullmac bus interface refactoring series.
It moves the module init/exit code to bus layer.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new feature in the dongle firmware requires a handshake during
firmware intialization. The request is sent in event packets which the
host driver is not able to handle before any net device registered.
Discard those packets as the context for handling it is missing.
The initialization handler will be added as part of feature support
code in the future.
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wait queue request_packet_wait was used in request_chain function
and for sake of consistency it has been renamed to request_chain_wait.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check for alignment is not valid anymore and can be removed. The
function is collapsed with brcmf_sdioh_request_packet() as a consequence
because it did not add much functionality any longer.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for handling FIF_PROMISC_IN_BSS, FIF_FCSFAIL,
FIF_CONTROL, FIF_OTHER_BSS and FIF_PSPOLL.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nvram file contains info for firmware which varies with different
hardware designs. Use more common firmware/nvram file names instead
of those in Linux firmware repository to avoid misunderstanding.
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function is only called with sk_buff parameter being non-zero so
the prototype does not need to support passing a char buffer any longer.
When the function is called with a NULL sk_buff parameter it returns
-EINVAL now.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_sdioh_request_buffer() was requiring a parameter in
its prototype that was not used within the function. It has been
removed consequently.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the receive path the buffer used to store the receive data from the
device can be a chain of sk_buff. It has been separated to allow the
use of skb queues.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In two places the next pointer was used to process a sk_buff chain
but it will always get a single sk_buff so this has been removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the receive path there was still code using the next pointer to
access all packets in skb_queue. This patch fixes that.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The conformance test limits (CTL) for each regulatory domains
(FCC/ETSI/MKK) are programmed for each runtime modes (11B,11G,
HT20 and HT40) in EEPROM. The lowest ctledge power value of a
particular running mode should not be used while computing
ctledge power for a different running mode.(i.e 11G's min ctledge
power should not be used while computing ctledge power for HT20).
Currently, the code does not handle this properly which would
result in incorrect txpowers in certain cases. So reset the
twiceMaxEdgePower to the default while computing min ctlegepower
for every mode.
Cc: David Quan <dquan@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When tx agg is being stopped TID is flushed using ath_tx_flush_tid. It
is possible that ath_tx_flush_tid completelly flushes TID (if all
packets in this TID have already been retried). If this happened
ath_tx_aggr_stop would leave TID in cleanup state permanently.
Fix this by making ath_tx_flush_tid remove AGGR_ADDBA_COMPLETE and
AGGR_CLEANUP flags from TID status if TID is empty.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SMPS regulator voltage control differs from the one of the LDO ones.
Current TWL code was using LDO regulator ops for controlling the SMPS
regulators, which fails. This was fixed fixed by adding separate
regulator type which uses correct logic and calculations for the
voltage levels.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by
commit 2577c6e8f2 (ath9k_hw: Add
support for AR946/8x chipsets) that caused a nasty regression to
appear on my Acer Ferrari One (the box locks up entirely at random
times after the wireless has been started without any way to get
debug information out of it).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julian Sikorski reports NEC uPD720200 does not work stable after suspend
and resume. Re-initialize the host in xhci_resume().
This should be backported to stable kernels as old as 2.6.37. The
kernel will need to include
commit c877b3b2ad
"xhci: Add reset on resume quirk for asrock p67 host"
for this patch to work.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Reported-by: Julian Sikorski <belegdol@gmail.com>
Tested-by: Julian Sikorski <belegdol@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This is caused by dereferencing 'rdev' after device_unregister() in
the regulator_unregister() function. 'rdev' is freed by
device_unregister(), so it must not be dereferenced after this call.
[Edited commit message for legibility -- broonie]
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In current implementation, the pointer ri is not NULL if no id is matched.
Fix it by checking i == ARRAY_SIZE(aat2870_regulators) if no id is matched.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This patch converts the drivers in drivers/net/irda/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To perform PHY calibration and set a different EA value by chip ID,
Whenever the NIC chip power on, ie booting or resuming, we need to
force HW to calibrate PHY parameter again, and also set a proper EA
value which gather from experiment.
Those procedures help to reduce compatible issues(NIC is unable to link
up in some special case) in giga speed.
Signed-off-by: AriesLee <AriesLee@jmicron.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using vlan 0 and UP 0, vlan header wasn't placed.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device must be in promiscuous mode or DMAC must be same as the host MAC, or
else packet will be dropped by the HW rx filtering.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 capability bits for WOL, one for each port.
WOL handlers were looking only on the second bit, regardless of the port.
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving to regular Completion Queue implementation (not collapsed)
Completion for each transmitted packet is written to new entry.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
the MLX4_EN_WOL_DO_MODIFY flag which is defined through enum targets
bit 63, this triggers a "cast truncate bits from constant value
(8000000000000000 becomes 0)" warning from sparse, fix that by using
define instead of enum.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using RSS which takes into account UDP headers is controlled by
a module param, fix the setting of the HW RSS context to align
with that scheme. So far it was uncoditionally allowing hashing
on the UDP headers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Towards adding RSS support for IB drivers/application who use
the mlx4 HW, make the RSS related definitions global and change
the mlx4_en driver to use them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the "ISDN4Linux interface" message from device registration,
where it is emitted for each device, to driver registration, where
it is emitted only once, for consistency with the CAPI variant.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'fbdev-for-linus' of git://github.com/schandinat/linux-2.6:
viafb: correct sync polarity for OLPC DCON
video:da8xx-fb: Disable and reset sequence on version2 of LCDC
OMAPDSS: DISPC: skip scaling calculations when not scaling
OMAPFB: fix compilation warnings due to missing include
OMAPDSS: HDMI: fix returned HDMI pixel clock
Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by
commit 2577c6e8f2 ("ath9k_hw: Add support for AR946/8x chipsets") that
caused a nasty regression to appear on my Acer Ferrari One (the box
locks up entirely at random times after the wireless has been started
without any way to get debug information out of it).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a potential integer overflow in do_insnlist_ioctl() if
userspace passes in a large insnlist.n_insns. The call to kmalloc()
would allocate a small buffer, leading to a memory corruption.
The bug was reported by Dan Carpenter <dan.carpenter@oracle.com>
and Haogang Chen <haogangchen@gmail.com>. The patch was suggested by
Ian Abbott <abbotti@mev.co.uk> and Lars-Peter Clausen <lars@metafoo.de>.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Haogang Chen <haogangchen@gmail.com>.
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit e384a41141.
It's not the correct way to solve this issue.
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qset->qh.link is an __le64 field and we should be using cpu_to_le64()
to fill it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kingston DT 101 G2 replies a wrong tag while transporting, add an
unusal_devs entry to ignore the tag validation.
Signed-off-by: Qinglin Ye <yestyle@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is an integer overflow here that could cause memory corruption
on 32 bit systems.
insnlist.n_insns could be a very high value size calculation for
kmalloc() could overflow resulting in a smaller "insns" than
expected. In the for (i = 0; i < insnlist.n_insns; i++) {... loop
we would read past the end of the buffer, possibly corrupting memory
as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After sleeping on a wait queue, signal_pending(current) should be
checked (not before sleeping).
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In comedi_fops, mmap_count is decremented at comedi_vm_ops->close but
it is not incremented at comedi_vm_ops->open. This may result in a negative
counter. The patch introduces the open method to keep the counter
consistent.
The bug was triggerd by this sample code:
mmap(0, ...., comedi_fd);
fork();
exit(0);
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes kernel oops when an USB DAQ device is plugged out while it's
communicating with the userspace software.
Signed-off-by: Bernd Porr <berndporr@f2s.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Interrupts must be disabled prior to calling usb_hcd_unlink_urb_from_ep.
If interrupts are not disabled, it can potentially lead to a deadlock.
The deadlock is readily reproduceable on a slower (ARM based) device
such as the TI Pandaboard.
Signed-off-by: Bart Westgeest <bart@elbrys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 798681bf "ARM: 7158/1: add new MFP implement for NUC900"
adds subname parameter for mfp_set_groupg.
Thus add subname parameter to the callers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix build failure in staging iio driver:
.../drivers/staging/iio/industrialio-core.c: In function 'iio_event_getfd':
.../drivers/staging/iio/industrialio-core.c:262:32: error:
'ev_int' undeclared (first use in this function)
Also convert the rest of the function to use the new variable.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tx_fifo_errors are tracked in start_xmit_ for virtio_net, but not
reported in the tallies returned by virtnet_stats(). Return them
as the rx "sub-stats" rx_length_errors and rx_frame_errors are.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're trying to check if any options are defined which isn't wha the
existing code does due to confusing & and &&.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_msg is defined to have a 1 entry array at the end, so gcc warns:
drivers/net/wireless/ray_cs.c: In function ‘rx_authenticate’:
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2439:15: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2452:16: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2453:18: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2453:32: warning: array subscript is above array bounds [-Warray-bounds]
Use a zero length array and rename to "ray_rx_msg" to make sure we hit all
of the necessary cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/airo.c: In function ‘encapsulate’:
drivers/net/wireless/airo.c:1421:15: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/airo.c: In function ‘decapsulate’:
drivers/net/wireless/airo.c:1509:16: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool EEPROM read/write support using the eeprom_93cx6
library instead of open-coding the functions.
Depends on eeprom_93cx6 driver getting EEPROM write support.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
[sboyd@codeaurora.org: Removed previous eeprom implementation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is off it is under power saving mode. Changing the MAC address
in that situation will result in the device not communicating as the first
write to the MAC address register is not executed.
Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com>
[ben@simtec.co.uk: cleaned up header]
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading the MAC address from the system registers if there
is an EEPROM present. This involves caching the KS_CCR register for later
use (will also be useful for ETHTOOL support) and adding a print to say
that there is an EEPROM present.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for writing data to EEPROM.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Linux Kernel <linux-kernel@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices need to know if the data is to be output or read, so add a
data direction into the eeprom structure to tell the driver whether the
data line should be driven.
The user in this case is the Micrel KS8851 which has a direction
control for the EEPROM data line and thus needs to know whether
to drive it (writing) or to tristate it for receiving.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When non power of two MSIX vectors are given to driver, some RX queues
are not utilized. Program RSS table in such a way that all queues
are utilized.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new hash key gives better distribution of packets across RX
queues.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detect error in Lancer by polling a HW register and
recover from this error if it is recoverable.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TX queues are created again after error recovery,
netif_set_real_num_tx_queues() is invoked to update number of real
TX queues created. rtnl lock needs to be held when invoking this routine.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SR-IOV implementation is Lancer has changed in following ways -
1)PF driver assigns one MAC addresses for VF using COMMON_SET_IFACE_MAC_LIST.
2)VF driver queries its MAC address using COMMON_GET_IFACE_MAC_LIST command
and assigns it to its interface.
Signed-off-by: Mammatha Edhala <mammatha.edhala@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This file is now unused and should have been removed by commit
7c89943236 ("bonding, ipv4, ipv6, vlan:
Handle NETDEV_BONDING_FAILOVER like NETDEV_NOTIFY_PEERS").
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 88491d8103 ("drivers/net: Kconfig
& Makefile cleanup") changed the type of these options to bool, but
they select code that could (and still can) be built as modules.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the drivers in drivers/hwmon/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: Simon Guinot <sguinot@lacie.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_register_driver(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
compatible in dts has been changed, so the driver needs to be updated
accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix below build error:
CC drivers/net/ethernet/marvell/mv643xx_eth.o
drivers/net/ethernet/marvell/mv643xx_eth.c: In function 'mv643xx_eth_get_drvinfo':
drivers/net/ethernet/marvell/mv643xx_eth.c:1505: error: 'info' undeclared (first use in this function)
drivers/net/ethernet/marvell/mv643xx_eth.c:1505: error: (Each undeclared identifier is reported only once
drivers/net/ethernet/marvell/mv643xx_eth.c:1505: error: for each function it appears in.)
make[4]: *** [drivers/net/ethernet/marvell/mv643xx_eth.o] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://github.com/rustyrussell/linux:
virtio-pci: make reset operation safer
virtio-mmio: Correct the name of the guest features selector
virtio: add HAS_IOMEM dependency to MMIO platform bus driver
virtio pci device reset actually just does an I/O
write, which in PCI is really posted, that is it
can complete on CPU before the device has received it.
Further, interrupts might have been pending on
another CPU, so device callback might get invoked after reset.
This conflicts with how drivers use reset, which is typically:
reset
unregister
a callback running after reset completed can race with
unregister, potentially leading to use after free bugs.
Fix by flushing out the write, and flushing pending interrupts.
This assumes that device is never reset from
its vq/config callbacks, or in parallel with being
added/removed, document this assumption.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix this compile error on s390:
CC [M] drivers/virtio/virtio_mmio.o
drivers/virtio/virtio_mmio.c: In function 'vm_get_features':
drivers/virtio/virtio_mmio.c:107:2: error: implicit declaration of function 'writel'
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Use round_jiffies_relative to align the ehea workqueue and avoid
extra wakeups.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we enable multiqueue by default the ehea driver is using
quite a lot of memory for its buffer pools. With 4 queues we
consume 64MB in the jumbo packet ring, 16MB in the medium packet
ring and 16MB in the tiny packet ring.
We should only fill the jumbo ring once the MTU is increased but
for now halve it's size so it consumes 32MB. Also reduce the tiny
packet ring, with 4 queues we had 16k entries which is overkill.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmiting a fragmented skb, qlge fills a descriptor with the
fragment addresses, after DMA-mapping them. If there are more than eight
fragments, it will use the eighth descriptor as a pointer to an external
list. After mapping this external list, called OAL to a structure
containing more descriptors, it fills it with the extra fragments.
However, considering that systems with pages larger than 8KiB would have
less than 8 fragments, which was true before commit a715dea3c8, it
defined a macro for the OAL size as 0 in those cases.
Now, if a skb with more than 8 fragments (counting skb->data as one
fragment), this would start overwriting the list of addresses already
mapped and would make the driver fail to properly unmap the right
addresses on architectures with pages larger than 8KiB.
Besides that, the list of mappings was one size too small, since it must
have a mapping for the maxinum number of skb fragments plus one for
skb->data and another for the OAL. So, even on architectures with page
sizes 4KiB and 8KiB, a skb with the maximum number of fragments would
make the driver overwrite its counter for the number of mappings, which,
again, would make it fail to unmap the mapped DMA addresses.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix port identify test on 5461x PHY by driving LEDs through MDIO.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu_assign_pointer(ptr, NULL) can be safely replaced by
RCU_INIT_POINTER(ptr, NULL)
(old rcu_assign_pointer() macro was testing the NULL value and could
omit the smp_wmb(), but this had to be removed because of compiler
warnings)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI hotplug: shpchp: don't blindly claim non-AMD 0x7450 device IDs
PCI: pciehp: wait 100 ms after Link Training check
PCI: pciehp: wait 1000 ms before Link Training check
PCI: pciehp: Retrieve link speed after link is trained
PCI: Let PCI_PRI depend on PCI
PCI: Fix compile errors with PCI_ATS and !PCI_IOV
PCI / ACPI: Make acpiphp ignore root bridges using PCIe native hotplug
Reported issues when using dev_kfree_skb() on UP systems and
systems with low numbers of cores. dev_kfree_skb_irq() will
properly save IRQ state before freeing the skb.
Tested on 3.1.1 and 3.2_rc2
Example of reproducible trace of kernel 3.1.1
------------[ cut here ]------------
WARNING: at kernel/softirq.c:159 local_bh_enable+0x32/0x79()
...
Pid: 0, comm: swapper Not tainted 3.1.1-gentoo #1
Call Trace:
[<c1022970>] warn_slowpath_common+0x65/0x7a
[<c102699e>] ? local_bh_enable+0x32/0x79
[<c1022994>] warn_slowpath_null+0xf/0x13
[<c102699e>] local_bh_enable+0x32/0x79
[<c134bfd8>] destroy_conntrack+0x7c/0x9b
[<c134890b>] nf_conntrack_destroy+0x1f/0x26
[<c132e3a6>] skb_release_head_state+0x74/0x83
[<c132e286>] __kfree_skb+0xb/0x6b
[<c132e30a>] consume_skb+0x24/0x26
[<c127c925>] b44_poll+0xaa/0x449
[<c1333ca1>] net_rx_action+0x3f/0xea
[<c1026a44>] __do_softirq+0x5f/0xd5
[<c10269e5>] ? local_bh_enable+0x79/0x79
<IRQ> [<c1026c32>] ? irq_exit+0x34/0x8d
[<c1003628>] ? do_IRQ+0x74/0x87
[<c13f5329>] ? common_interrupt+0x29/0x30
[<c1006e18>] ? default_idle+0x29/0x3e
[<c10015a7>] ? cpu_idle+0x2f/0x5d
[<c13e91c5>] ? rest_init+0x79/0x7b
[<c15c66a9>] ? start_kernel+0x297/0x29c
[<c15c60b0>] ? i386_start_kernel+0xb0/0xb7
---[ end trace 583f33bb1aa207a9 ]---
Signed-off-by: Xander Hover <LKML@hover.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
drm: integer overflow in drm_mode_dirtyfb_ioctl()
drivers/gpu/vga/vgaarb.c: add missing kfree
drm/radeon/kms/atom: unify i2c gpio table handling
drm/radeon/kms: fix up gpio i2c mask bits for r4xx for real
ttm: Don't return the bo reserved on error path
drm/radeon/kms: add a CS ioctl flag not to rewrite tiling flags in the CS
drm/i915: Fix inconsistent backlight level during disabled
drm, i915: Fix memory leak in i915_gem_busy_ioctl().
drm/i915: Use DPCD value for max DP lanes.
drm/i915: Initiate DP link training only on the lanes we'll be using
drm/i915: Remove trailing white space
drm/i915: Try harder during dp pattern 1 link training
drm/i915: Make DP prepare/commit consistent with DP dpms
drm/i915: Let panel power sequencing hardware do its job
drm/i915: Treat PCH eDP like DP in most places
drm/i915: Remove link_status field from intel_dp structure
drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
drm/i915: Module parameters using '-1' as default must be signed type
drm/i915: Turn on another required clock gating bit on gen6.
drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
...
Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.
Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain
With above expr, number of voltages that can be selected is
step value count * gain count
constant for gain count will be called VDD1_2_NUM_VOLT_COARSE
existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Genera Touch told us that 0001 is their single point device
and 0003 is the multitouch one. Apparently, we made the tests
someone having a prototype, and not the final product.
They said it should be safe to do the switch.
This partially reverts 5572da0 ("HID: hid-mulitouch: add support
for the 'Sensing Win7-TwoFinger'").
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The function i2cdev_notifier_call is used only in i2c-dev file
making it static.
Also removes the following sparse warning
drivers/i2c/i2c-dev.c:582:5: warning: symbol 'i2cdev_notifier_call'
was not declared. Should it be static?
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
The wrong bits were put on the wire, fix that.
This fixes kernel bug #42562.
Signed-off-by: Sheng-Hui J. Chu <jeffchu@broadcom.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a potential integer overflow in drm_mode_dirtyfb_ioctl()
if userspace passes in a large num_clips. The call to kmalloc would
allocate a small buffer, and the call to fb->funcs->dirty may result
in a memory corruption.
Reported-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current code checks if abs(delta_delta.tv_sec) is greater or
equal to two before it discards the old delta value, but this can
trigger at close to -1 seconds since -1.000000001 seconds is stored
as tv_sec -2 and tv_nsec 999999999 in a normalized timespec.
rtc_resume had an early return check if the rtc value had not changed
since rtc_suspend. This effectivly stops time for the duration of the
short sleep. Check if sleep_time is positive after all the adjustments
have been applied instead since this allows the old_system adjustment
in rtc_suspend to have an effect even for short sleep cycles.
CC: stable@kernel.org
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Currently, the RTC code does not disable the alarm in the hardware.
This means that after a sequence such as the one below (the files are in the
RTC sysfs), the box will boot up after 2 minutes even though we've
asked for the alarm to be turned off.
# echo $((`cat since_epoch`)+120) > wakealarm
# echo 0 > wakealarm
# poweroff
Fix this by disabling the alarm when there are no timers to run.
Cc: stable@kernel.org
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This reverts commit dc93728084.
As requested by Ben Herrenschmidt:
"This breaks some powerpc platforms at least. The practice of having
a node provide an explicit "interrupt-parent" property pointing to
itself is an old trick that we've used in the past to allow a
device-node to have interrupts routed to different controllers.
In that case, the node also contains an interrupt-map, so the node is
its own parent, the interrupt resolution hits the map, which then can
route each individual interrupt to a different parent."
Grant says:
"Ah, nuts, yes that is broken then. Yes, please revert the commit and
Rob & I will come up with a better solution.
Rob, I think it can be done by explicitly checking for np ==
desc->interrupt_parent in of_irq_init() instead of relying on
of_irq_find_parent() returning NULL."
Requested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Given we dont use anymore the struct net_device *dev argument, and this
interface brings litle benefit, remove netdev_{alloc|free}_page(), to
debloat include/linux/skbuff.h a bit.
(Some drivers used a mix of these interfaces and alloc_pages())
When allocating a page given to device for DMA transfer (device to
memory), it makes sense to use a cold one (__GFP_COLD)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
C assignment can handle struct in6_addr copying.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4ba7d99978.
The original patch was a misguided attempt to improve performance on
some hardware that is apparently prone to spurious interrupt generation.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 23085d5796.
The original patch was a misguided attempt to improve performance on
some hardware that is apparently prone to spurious interrupt generation.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mount_subtree() pointless use-after-free
iio: fix a leak due to improper use of anon_inode_getfd()
microblaze: bury asm/namei.h
Future devices may or may not be capable of supporting larger rx
producer rings. This patch changes the code so that this flag is set on
an ASIC rev to ASIC rev basis. Also, this patch changes a place where
the LRG_PROD_RING_CAP flag was not controlling how the rx standard
producer ring size was set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BD replenish thresholds for the 57765 and newer ASIC revs are a
little strict. They were tuned for a mode that is currently unused.
This patch relaxes the thresholds so that they are set to values more
inline with the resources available.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes tg3's 1000Base-X flow control resolution to look like
the 1000Base-T flow control resolution code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This considers some simple cases that are common and easy to validate
Note in particular that there are no ...s in the rule, so all of the
matched code has to be contiguous
The semantic patch that makes this change is available
in scripts/coccinelle/api/alloc/kzalloc-simple.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuf is a buffer that is local to this function, so all of the error paths
leaving the function should release it.
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 28011cf19b (net: Add ethtool to mii advertisment conversion
helpers) added a helper function ethtool_adv_to_mii_100bt() and
tg3_copper_is_advertising_all(), tg3_phy_autoneg_cfg() were
modified to use this.
Before that commit, ethtool to mii advertisement conversion was
done wrt speed, but now pause operation is also taken account.
So, in tg3_copper_is_advertising_all(), below condition becomes
true and this makes link up fails.
if ((adv_reg & ADVERTISE_ALL) != all_mask)
return 0;
To fix this add ADVERTISE_ALL bit and operation to cap speed,
and change default advertisement not including ADVERTISED_Pause.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the quirks and i2c_rec assignment into separate
functions used by both radeon_lookup_i2c_gpio() and
radeon_atombios_i2c_init(). This avoids duplicating code
and cases where quirks were only added to one of the
functions.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes i2c test failures when i2c_algo_bit.bit_test=1.
The hw doesn't actually require a mask, so just set it
to the default mask bits for r1xx-r4xx radeon ddc.
I missed this part the first time through.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
An unlikely race could case a bo to be returned reserved on an error path.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux: (25 commits)
drm/i915: Fix inconsistent backlight level during disabled
drm, i915: Fix memory leak in i915_gem_busy_ioctl().
drm/i915: Use DPCD value for max DP lanes.
drm/i915: Initiate DP link training only on the lanes we'll be using
drm/i915: Remove trailing white space
drm/i915: Try harder during dp pattern 1 link training
drm/i915: Make DP prepare/commit consistent with DP dpms
drm/i915: Let panel power sequencing hardware do its job
drm/i915: Treat PCH eDP like DP in most places
drm/i915: Remove link_status field from intel_dp structure
drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
drm/i915: Module parameters using '-1' as default must be signed type
drm/i915: Turn on another required clock gating bit on gen6.
drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
drm/i915: enable cacheable objects on Ivybridge
drm/i915: add constants to size fence arrays and fields
drm/i915: Ivybridge still has fences!
drm/i915: forcewake warning fixes in debugfs
drm/i915: Fix object refcount leak on mmappable size limit error path.
drm/i915: Use mode_config.mutex in ironlake_panel_vdd_work
...
drivers/net/wireless/rtlwifi/usb.c: In function ‘_usb_read_sync’:
drivers/net/wireless/rtlwifi/usb.c:102:6: warning: ‘status’ may be used uninitialized in this function
drivers/net/wireless/rtlwifi/usb.c:102:6: note: ‘status’ was declared here
My compiler is dumb, but better to eliminate the warning than to have
anyone waste time evaluating this again...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: fix more ET131X build errors
staging: et131x depends on NET
staging: slicoss depends on NET
linux-next: et131x: Fix build error when CONFIG_PM_SLEEP not enabled
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (48 commits)
USB: Fix Corruption issue in USB ftdi driver ftdi_sio.c
USB: option: add PID of Huawei E173s 3G modem
OHCI: final fix for NVIDIA problems (I hope)
USB: option: release new PID for ZTE 3G modem
usb: Netlogic: Fix HC_LENGTH call in ehci-xls.c
USB: storage: ene_ub6250: fix compile warnings
USB: option: add id for 3G dongle Model VT1000 of Viettel
USB: serial: pl2303: rm duplicate id
USB: pch_udc: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
USB: pch_udc: Support new device LAPIS Semiconductor ML7831 IOH
usb-storage: Accept 8020i-protocol commands longer than 12 bytes
USB: quirks: adding more quirky webcams to avoid squeaky audio
powerpc/usb: fix type cast for address of ioremap to compatible with 64-bit
USB: at91: at91-ohci: fix set/get power
USB: cdc-acm: Fix disconnect() vs close() race
USB: add quirk for Logitech C600 web cam
USB: EHCI: fix HUB TT scheduling issue with iso transfer
USB: XHCI: resume root hubs when the controller resumes
USB: workaround for bug in old version of GCC
USB: ark3116 initialisation fix
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: ldisc, wait for ldisc infinitely in hangup
TTY: ldisc, move wait idle to caller
TTY: ldisc, allow waiting for ldisc arbitrarily long
Revert "tty/serial: Prevent drop of DCD on suspend for Tegra UARTs"
RS485: fix inconsistencies in the meaning of some variables
pch_uart: Fix DMA resource leak issue
serial,mfd: Fix CMSPAR setup
tty/serial: Prevent drop of DCD on suspend for Tegra UARTs
pch_uart: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_uart: Support new device LAPIS Semiconductor ML7831 IOH
pch_uart: Fix hw-flow control issue
tty: hvc_dcc: Fix duplicate character inputs
jsm: Change maintainership
* 'char-misc-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: ad525x_dpot: Fix AD8400 spi transfer size.
pch_phub: Fix MAC address writing issue for LAPIS ML7831
pch_phub: Improve ADE(Address Decode Enable) control
pch_phub: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_phub: Support new device LAPIS Semiconductor ML7831 IOH
pcie-gadget-spear: Add "platform:" prefix for platform modalias
MAINTAINERS: add CHAR and MISC driver maintainers
While the OLPC display appears to be able to handle either positive
or negative sync, the Display Controller only recognises positive sync.
This brings viafb (for XO-1.5) in line with lxfb (for XO-1) and
fixes a recent regression where the XO-1.5 DCON could no longer be
frozen. Thanks to Florian Tobias Schandinat for helping identify
the fix.
Test case: from a vt,
echo 1 > /sys/devices/platform/dcon/freeze
should cause the current screen contents to freeze, rather than garbage being
displayed.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@kernel.org
Patch follows the disable and software reset sequence specified
in version2 to LCDC functional specification.
Without this flicker is observed on re-enabling the LCDC.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It was pointed out by "make versioncheck" that we do not need to include
version.h in drivers/net/can/sja1000/peak_pci.c
This patch removes the unneeded include.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the past, it was fine to simply call
dev_kfree_skb when it was impossible to
transmit a skb. However, with the new
tx status API:
"mac80211: implement wifi TX status"
Every loose skb needs to be handed back
to mac80211.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the past, it was fine to simply call
dev_kfree_skb when it was impossible to
transmit a skb. However, with the new
tx status API:
"mac80211: implement wifi TX status"
Every loose skb needs to be handed back
to mac80211.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NET_TYPE_11FB actually has never been used.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert old WEXT reporting to use new cfg80211_pmksa_candidate_notify().
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some structures were missing __packed.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_roamed() now has channel parameter so add passing current channel
info.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split getting current channel channel from hardware to separate function
as this function will be needed later in patch 'pass channel info to
cfg80211_roamed()'.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 implements these for all devices,
but given restrictions of some devices that isn't
really true, so prepare for being able to remove the
capability for some mac80211 devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using dev_err instead of dev_printk(KERN_ERR uses fewer
arguments and is a bit smaller.
Deduplicating formats used by IWL_DEBUG_QUIET_RFKILL also
makes the object a bit smaller.
Neatened the macros, used ##__VA_ARGS__.
$ size drivers/net/wireless/iwlwifi/built-in.o*
text data bss dec hex filename
462652 8646 92576 563874 89aa2 drivers/net/wireless/iwlwifi/built-in.o.new
467557 8646 92592 568795 8addb drivers/net/wireless/iwlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove this redundancy.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the CPUed version of the variables when printing data from the
BA notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some information was redundation, other was missing.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add more information when a queue is stuck and actually get
information from the scheduler instead of looking at internal
variables.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt routine for PCI devices has a special exit that
executes the same instructions as does the normal exit.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtlwifi fails on a big-endian host.
These changes have been tested on a Mac PowerBook G4, which has
a PPC processor.
Although this patch touches some of the code that will affect endian
issues on PCI hardware through drivers rtl8192ce, rtl8192se, and
rtl8192de, these have not been tested due to lack of suitable hardware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtl8192cu writes the firmware with 32-bit asynchronous writes. This
design is OK for USB 2.0 adapters, but the current implementation of
xhcu-hcd has a limited ring size, which is exceeded. By converting to
synchronous block writes, this error is avoided.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB driver does not retry reads - allow 10 tries.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DFS events are reported as PHY errors and need to be processed
with a correct timestamp set before ath9k_skb_preprocess() is
called and the frame is possibly dropped.
This patch puts the rxs->mactime calculation before the skb
is preprocessed to prepare for DFS event reporting.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is very similar to bnx2x conversion, but simpler since no special
alignement is required, so goal was not to reduce skb truesize.
Using build_skb() reduces cache line misses in the driver, since we
use cache hot skb instead of cold ones. Number of in-flight sk_buff
structures is lower, they are more likely recycled in SLUB caches
while still hot.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to mask the MMC irq otherwise if we raise the mmc
interrupts that are not handled the driver loops in the
handler.
In fact, by default all mmc counters (only used for stats)
are managed in SW and registers are cleared on each READ.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements advice by Ben Hutchings to change the mii side of
the function names to look more like the register whose values they
convert. New LPA translation functions have been added as well.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This considers some simple cases that are common and easy to validate
Note in particular that there are no ...s in the rule, so all of the
matched code has to be contiguous
The semantic patch that makes this change is available
in scripts/coccinelle/api/alloc/kzalloc-simple.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that makes this change is available
in scripts/coccinelle/api/alloc/drop_kmalloc_cast.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
"remote_list" is of type
struct dma_chunk remote_list[VETH_MAX_FRAMES_PER_MSG];
Probably a copy'n'paste error.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not used outside of the driver so doesn't need to be exported, and
sparse notices this and complains about it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
"dwrq->length" is the capped version of "essid->length".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
This was broken by commit 7759995c75 (yes,
myself). The basic problem here is since the digest state is only saved
after the last chunk, the state array is only valid when handling the
first chunk of the next buffer. Broken since linux-3.0.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Cc: <stable@kernel.org> # 3.1.x
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (86 commits)
ipv4: fix redirect handling
ping: dont increment ICMP_MIB_INERRORS
sky2: fix hang in napi_disable
sky2: enforce minimum ring size
bonding: Don't allow mode change via sysfs with slaves present
f_phonet: fix page offset of first received fragment
stmmac: fix pm functions avoiding sleep on spinlock
stmmac: remove spin_lock in stmmac_ioctl.
stmmac: parameters auto-tuning through HW cap reg
stmmac: fix advertising 1000Base capabilties for non GMII iface
stmmac: use mdelay on timeout of sw reset
sky2: version 1.30
sky2: used fixed RSS key
sky2: reduce default Tx ring size
sky2: rename up/down functions
sky2: pci posting issues
sky2: fix hang on shutdown (and other irq issues)
r6040: fix check against MCRO_HASHEN bit in r6040_multicast_list
MAINTAINERS: change email address for shemminger
pch_gbe: Move #include of module.h
...
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Suspend: Fix bug in suspend statistics update
PM / Hibernate: Fix the early termination of test modes
PM / shmobile: Fix build of sh7372_pm_init() for CONFIG_PM unset
PM Sleep: Do not extend wakeup paths to devices with ignore_children set
PM / driver core: disable device's runtime PM during shutdown
PM / devfreq: correct Kconfig dependency
PM / devfreq: fix use after free in devfreq_remove_device
PM / shmobile: Avoid restoring the INTCS state during initialization
PM / devfreq: Remove compiler error after irq.h update
PM / QoS: Properly use the WARN() macro in dev_pm_qos_add_request()
PM / Clocks: Only disable enabled clocks in pm_clk_suspend()
ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix
PM / shmobile: Don't skip debugging output in pd_power_up()
This adds a new optional chunk to the CS ioctl that specifies optional flags
to the CS parser. Why this is useful is explained below. Note that some regs
no longer need the NOP relocation packet if this feature is enabled.
Tested on r300g and r600g with this flag disabled and enabled.
Assume there are two contexts sharing the same mipmapped tiled texture.
One context wants to render into the first mipmap and the other one
wants to render into the last mipmap. As you probably know, the hardware
has a MACRO_SWITCH feature, which turns off macro tiling for small mipmaps,
but that only applies to samplers.
(at least on r300-r500, though later hardware likely behaves the same)
So we want to just re-set the tiling flags before rendering (writing
packets), right? ... No. The contexts run in parallel, so they may
set the tiling flags simultaneously and then fire their command streams
also simultaneously. The last one setting the flags wins, the other one
loses.
Another problem is when one context wants to render into the first and
the last mipmap in one CS. Impossible. It must flush before changing
tiling flags and do the rendering into the smaller mipmaps in another CS.
Yet another problem is that writing copy_blit in userspace would be a mess
involving re-setting tiling flags to please the kernel, and causing races
with other contexts at the same time.
The only way out of this is to send tiling flags with each CS, ideally
with each relocation. But we already do that through the registers.
So let's just use what we have in the registers.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (exynos4_tmu) Fix Kconfig dependency
[ Merging code in-flight, just because I can. What timezone should I
use? - Linus ]
Randy Dunlap reports that the ex131x driver doesn't build when CONFIG_PM_SLEEP is not enabled.
This bug was introduced when moving code around to remove some forward declarations earlier, the #endif part of #ifdef CONFIG_PM_SLEEP was not moved at the same time. Now fixed by moving it to its proper place.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently using variable-length array is not correct
(https://lkml.org/lkml/2011/10/23/25). So remove it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for ftdi_set_termios() glitching output
ftdi_set_termios() is constantly setting the baud rate, data bits and parity
unnecessarily on every call, . When called while characters are being
transmitted can cause the FTDI chip to corrupt the serial port bit stream
output by stalling the output half a bit during the output of a character.
Simple fix by skipping this setting if the baud rate/data bits/parity are
unchanged.
Signed-off-by: Andrew Worsley <amworsley@gmail.com>
Cc: stable <stable@vger.kernel.org>
----
I had a brief run with strace on the getty and it was doing ioctl()s on
each call but it didn't look relavant to the problem. I think the issue is
that XON/XOFF flow control was being implmented via hardware - for the ixoff
to allow the user to use XON/XOFF to control output. Unfortunately it would
send 3 Control URBs updating all of the settings after each piece of input
I am trying to work around the issue of gmail messing with the tab/spacing
by submitting via SMTP via gmail which I believe should fix the issue.
The patch is against v3.2-rc2 and compiles - but no additional testing in
this kernel has been done.
Thanks
Andrew
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Problems with NVIDIA's OHCI host controllers persist. After looking
carefully through the spec, I finally realized that when a controller
is reset it then automatically goes into a SUSPEND state in which it
is completely quiescent (no DMA and no IRQs) and from which it will
not awaken until the system puts it into the OPERATIONAL state.
Therefore there's no need to worry about controllers being in the
RESET state for extended periods, or remaining in the OPERATIONAL
state during system shutdown. The proper action for device
initialization is to put the controller into the RESET state (if it's
not there already) and then to issue a software reset. Similarly, the
proper action for device shutdown is simply to do a software reset.
This patch (as1499) implements such an approach. It simplifies
initialization and shutdown, and allows the NVIDIA shutdown-quirk code
to be removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com>
Tested-by: Arno Augustin <Arno.Augustin@web.de>
Cc: stable <stable@vger.kernel.org> [after tested in 3.2 for a while]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds new PIDs for ZTE 3G modem, after we confirm it and tested.
Thanks for Dan's work at kernel option devier.
Signed-off-by: Alvin.Zheng <zheng.zhijian@zte.com.cn>
Signed-off-by: wsalvin <wsalvin@yahoo.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix compile error, HC_LENGTH now takes two parameters and ehci
needs to be passed as the first parameter.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch to fix the error message "directives may not be used inside a macro
argument" which appears when the kernel is compiled for the cris architecture.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen-gntalloc: signedness bug in add_grefs()
xen-gntalloc: integer overflow in gntalloc_ioctl_alloc()
xen-gntdev: integer overflow in gntdev_alloc_map()
xen:pvhvm: enable PVHVM VCPU placement when using more than 32 CPUs.
xen/balloon: Avoid OOM when requesting highmem
xen: Remove hanging references to CONFIG_XEN_PLATFORM_PCI
xen: map foreign pages for shared rings by updating the PTEs directly
* 'for-linus' of git://git.kernel.dk/linux-block:
block: add missed trace_block_plug
paride: fix potential information leak in pg_read()
bio: change some signed vars to unsigned
block: avoid unnecessary plug list flush
cciss: auto engage SCSI mid layer at driver load time
loop: cleanup set_status interface
include/linux/bio.h: use a static inline function for bio_integrity_clone()
loop: prevent information leak after failed read
block: Always check length of all iov entries in blk_rq_map_user_iov()
The Windows driver .inf disables ASPM on all cciss devices. Do the same.
backing-dev: ensure wakeup_timer is deleted
block: Revert "[SCSI] genhd: add a new attribute "alias" in gendisk"
* 'unicore32' of git://github.com/gxt/linux:
unicore32, exec: remove redundant set_fs(USER_DS)
unicore32: Fix typo 'PUV3_I2C'
unicore32: drop unused Kconfig symbols
rtc: rtc-puv3: Add __devinit and __devexit markers for probe and remove
arch/unicore32: do not use EXTRA_AFLAGS or EXTRA_CFLAGS
unicore32: fix build error for find bitops
Current code calculates scaling factors for video overlays even when the
overlays are not scaled. Change the code to skip calculations when not
scaling.
This optimizes the code a bit, but also fixes a problem when configuring
an overlay for a disabled display: if the display is disabled we don't
necessarily know the pixel clock used when the display is enabled, and
in some cases (like HDMI) the pixel clock is set to zero until a proper
video mode is set later. A wrong pixel clock will mess up the
scaling calculations, causing an error like:
omapdss DISPC error: failed to set up scaling, required fclk rate = 0
Hz, current fclk rate = 170666666 Hz
A proper fix would be to check later whether the clocks are enough for the
scaling, at the point when the overlay or display is actually enabled,
but this patch removes the problem for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix warnings similar to this by including module.h:
drivers/video/omap/dispc.c:276:1: warning: data definition has no type
or storage class
drivers/video/omap/dispc.c:276:1: warning: type defaults to 'int' in
declaration of 'EXPORT_SYMBOL'
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_get_pixel_clock() returns the pixel clock in Hz, but the pck is
stored as kHz. This means the return value has to be multiplied by 1000,
not by 10000 as the code did.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The software stats are updated from BH, this change ensures that 32b
UP hosts use appropriate protection.
Tested:
- HW/SW stats consistent with pktgen (in particular tx=rx)
- HW/SW stats consistent when tx/rx offloads disabled
- no problem with+without lockdep (SMP 16-way)
Signed-off-by: David Decotigny <david.decotigny@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is very similar to bnx2x conversion, but bnx2 only requires 16bytes
alignement at start of the received frame to store its l2_fhdr, so goal
was not to reduce skb truesize (in fact it should not change after this
patch)
Using build_skb() reduces cache line misses in the driver, since we
use cache hot skb instead of cold ones. Number of in-flight sk_buff
structures is lower, they are more likely recycled in SLUB caches
while still hot.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If IRQ was never initialized, then calling napi_disable() would hang.
Add more bookkeeping to track whether IRQ was ever initialized.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has a restriction that the minimum ring size possible
is 128. The number of elements used is controlled by tx_pending and
the overall number of elements in the ring tx_ring_size, therefore it
is okay to limit the number of elements in use to a small value (63)
but still provide a bigger ring.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing mode via bonding's sysfs, the slaves are not initialized
correctly. Forbid to change modes with slaves present to ensure that every
slave is initialized correctly via bond_enslave().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The re-binding (unbind..bind) of an EMAC device fails because the
static variable "busy_phy_map" is not updated when the device is
removed.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We pull one byte (the MAC header) from the first fragment before the
fragment is actually appended. So the socket buffer length is 1, not 0.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the brightness property is inquired while the backlight is disabled,
the driver returns a wrong value (zero) because it probes the value after
the backlight was turned off. This caused a black screen even after the
backlight is enabled again. It should return the internal backlight_level
instead, so that it won't be influenced by the backlight-enable state.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=41926
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/872652
Tested-by: Kamal Mostafa <kamal@canonical.com>
Cc: Alex Davis <alex14641@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Keith Packard <keithp@keithp.com>
The buf_lock cannot be held while populating the inodes, so make the backend
pass forward an allocated and filled buffer instead. This solves the following
backtrace. The effect is that "buf" is only ever used to notify the backends
that something was written to it, and shouldn't be used in the read path.
To replace the buf_lock during the read path, isolate the open/read/close
loop with a separate mutex to maintain serialized access to the backend.
Note that is is up to the pstore backend to cope if the (*write)() path is
called in the middle of the read path.
[ 59.691019] BUG: sleeping function called from invalid context at .../mm/slub.c:847
[ 59.691019] in_atomic(): 0, irqs_disabled(): 1, pid: 1819, name: mount
[ 59.691019] Pid: 1819, comm: mount Not tainted 3.0.8 #1
[ 59.691019] Call Trace:
[ 59.691019] [<810252d5>] __might_sleep+0xc3/0xca
[ 59.691019] [<810a26e6>] kmem_cache_alloc+0x32/0xf3
[ 59.691019] [<810b53ac>] ? __d_lookup_rcu+0x6f/0xf4
[ 59.691019] [<810b68b1>] alloc_inode+0x2a/0x64
[ 59.691019] [<810b6903>] new_inode+0x18/0x43
[ 59.691019] [<81142447>] pstore_get_inode.isra.1+0x11/0x98
[ 59.691019] [<81142623>] pstore_mkfile+0xae/0x26f
[ 59.691019] [<810a2a66>] ? kmem_cache_free+0x19/0xb1
[ 59.691019] [<8116c821>] ? ida_get_new_above+0x140/0x158
[ 59.691019] [<811708ea>] ? __init_rwsem+0x1e/0x2c
[ 59.691019] [<810b67e8>] ? inode_init_always+0x111/0x1b0
[ 59.691019] [<8102127e>] ? should_resched+0xd/0x27
[ 59.691019] [<8137977f>] ? _cond_resched+0xd/0x21
[ 59.691019] [<81142abf>] pstore_get_records+0x52/0xa7
[ 59.691019] [<8114254b>] pstore_fill_super+0x7d/0x91
[ 59.691019] [<810a7ff5>] mount_single+0x46/0x82
[ 59.691019] [<8114231a>] pstore_mount+0x15/0x17
[ 59.691019] [<811424ce>] ? pstore_get_inode.isra.1+0x98/0x98
[ 59.691019] [<810a8199>] mount_fs+0x5a/0x12d
[ 59.691019] [<810b9174>] ? alloc_vfsmnt+0xa4/0x14a
[ 59.691019] [<810b9474>] vfs_kern_mount+0x4f/0x7d
[ 59.691019] [<810b9d7e>] do_kern_mount+0x34/0xb2
[ 59.691019] [<810bb15f>] do_mount+0x5fc/0x64a
[ 59.691019] [<810912fb>] ? strndup_user+0x2e/0x3f
[ 59.691019] [<810bb3cb>] sys_mount+0x66/0x99
[ 59.691019] [<8137b537>] sysenter_do_call+0x12/0x26
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
A call to i915_add_request() has been made in function i915_gem_busy_ioctl(). i915_add_request can fail,
so in it's exit path previously allocated memory needs to be freed.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Don't use the interruptible variant of mutex_lock(). It doesn't really
need to be interruptible. This avoids nasty error handling.
Signed-off-by: Michael Buesch <m@bues.ch>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert various seemingly still compiled wireless drivers' .get_drvinfo
routines to use the preferred strlcpy() routine.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yaniv Rosner