Move the code which is not parsing dt from pm8916_wcd_analog_parse_dt()
to make it clear to reader.
No functional changes done.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 integrated codec has a stereo "Line In" input. Add support for
it to the playback paths.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with different register offsets. The analog paths are very
different. There are more inputs and outputs. The ADC mux has been
replaced with a proper mixer.
This patch adds support for the basic playback path of the A31 codec,
from the DAC to the headphones. Headphone detection, microphone,
signaling, other inputs/outputs and capture will be added later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the DMA engine API documentation, maxburst denotes the
largest possible size of a single transfer, so as not to overflow
destination FIFOs as explained in this excerpt from dmaengine.h
* @src_maxburst: the maximum number of words (note: words, as in
* units of the src_addr_width member, not bytes) that can be sent
* in one burst to the device. Typically something like half the
* FIFO depth on I/O peripherals so you don't overflow it. This
* may or may not be applicable on memory sources.
* @dst_maxburst: same as src_maxburst but for destination target
* mutatis mutandis.
The TX FIFO is 64 samples deep for stereo, and the RX FIFO is 16
samples deep. So maxburst could be 32 and 8 for TX and RX respectively.
Unfortunately the sunxi DMA controller driver takes maxburst as
the requested burst size, rather than a limit, and returns an error
for unsupported values. The original value was 4, but some later
SoCs do not officially support this burst size.
This patch increases maxburst on the TX side to 8, which is supported
by all variants of the sunxi DMA controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with just different register offsets. The analog paths are
very different. There are more inputs and outputs.
The A31s, A23, and H3 have a similar PCM interface, again with register
offsets slightly rearranged. The analog path controls, while very
similar between them and the A31, have been moved a separate bus which
is accessed through a message box like interface in the PRCM address
range. This would be handled by a separate auxiliary device tied in
through the device tree in its supporting create_card function.
The quirks structure is expanded to include different register offsets
and separate callbacks for creating the ASoC card. The regmap_config,
quirks, and of_device_match tables have been moved to facilitate this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This revises existing comments in the register definition macros
section, and adds a few more, so that readers can clearly identify
the types of control registers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio codec on later Allwinner SoCs have a different layout and
audio path compared to the A10/A20. However the PCM parts are still
the same.
The different layout and audio paths mean we need a different
create_card function for different families, so they can create
DAPM endpoint widgets and routes.
This patch moves the regmap configs, quirks and of_device_id
structures to just before the probe function, so we can, among other
things, include a pointer for the create_card function. None of the
lines of code were changed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For device opened/closed, we check the D0i3 capability for the device
and invoke skl_tplg_d0i3_get/put, which counts the use case based on the
mode supported.
These counters are then used to decide if the device can enter D0i3 mode
of streaming or non-streaming or no D0i3.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all use cases can support Doi3. Only certain use cases like hot word
detection, deep buffering can support D0i3 based on resource requirement.
So, pass the D0i3 capability for the FE/BE copier using topology. This will
be used to take a decision for D0i3 mode entry/exit.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For D0i3, we need to tell DSP to run the pipelines in LP mode. This
information is kept in topology and passed to driver as an attribute
for pipe.
So add a new tuple for lpmode and program the pipe based on value set.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver needs two DSP callback, one to set D0i0 (active) and D0i3
(low-power) states.
Add these callbacks in dsp ops and implement them for broxton platforms.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To set the controller in D0i3 mode, the driver needs to set D0i3C
register after DSP is quiesced. Since the D0iX entry/exit is done by IPC,
add this as callback so that it can be invoked from IPC module.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio DSP supports intermediate power states between D0 and D3
states. These states are D0i0 and D0i3 states.
Collectively we refer these two states as D0iX states.
To set or wake up from these states, driver also needs to send an IPC "Set D0iX
IPC" before doing anything else.
Add support for this new IPC messages.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the DSP is in low power mode, it needs to be woken up by a "wake" IPC
to set it into the D0 state before we can send any other IPC command.
The call flow is that the driver calls sst_ipc_tx_message_wait() to send any
IPC and this call checks if the device is in low power mode and in that
case we need to send the wake IPC.
So add a new IPC nopm variant which can be called from driver and
doesn't check for power state (as we already know that) and avoids
circular dependency of again checking power state.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2s driver was only implementing playback for now. Implement capture to
make sure that's not a limitation anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the remaining update to PCM ABI object of version 5.
The flags will be applied to FE (Front End) links and can also be used
by physical links. The private data is reserved for future extension, so
offset update will add the private data size.
Now user space is using ABI v4, and the previous patch "ASoC: topology:
make PCM backward compatible from ABI v4" can assure the backward
compatibility.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Users start to use topology ABI from v4. ABI v5 updated existing manifest
and PCM elements. Two previous patches can support these ABI updates in a
backward compatible way. So if the topology file from user space is
generated by ABI v4, kernel will no longer quit but continue parsing.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
User space may not always set a valid FE DAI driver's name, FE DAI link's
name, stream name or cpu DAI name. In such cases, there are all ZERO in
these name string buffers of a topology PCM object. This patch will only
duplicate valid name strings for kernel FE DAI driver and DAI link when
creating them from topology, and free the name strings when destroying
them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for old version 4 of PCMs (FE DAI & DAI links).
Topology ABI v5 added new fields to stream caps and thus changed PCMs.
Since user space may still uses v4, kernel will check the ABI version by
comparing the object size. If user space uses v4 of PCMs, kernel will
create the latest version of PCMs from the old version, and use the new
version internally to create FE DAI & DAI links. Because these new created
PCM elements will be freed later, kernel need duplicate the name strings
of DAI driver and DAI links when creating them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add depends on HAS_DMA to Kconfig. This fixes error reported
by kbuild test robot when building for ARCH=m32r:
ERROR: "bad_dma_ops" [sound/soc/bcm/snd-soc-cygnus.ko] undefined!
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While DAPM is mono or single channel, its controls can be shared between
widgets, such as sharing one stereo mixer control between the left and
right channel widgets. An example such as the following routes
[Line In Left]----------<Line In Playback Switch>-------[Left Mixer]
^
^ ^ | ^
(inputs) (paths) <shared stereo mixer control> (outputs)
v v | v
v
[Line In Right]---------<Line In Playback Switch>-------[Right Mixer]
where we have separate widgets and paths for the left and right channels
from "Line In" to "Mixer", but a shared stereo mixer control for the
2 paths.
This patch introduces support for such shared mixer controls, allowing
more than 1 path to be attached to a single stereo control, and being
able to control left/right channels independently.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support double channel shared controls split across 2 registers, one
for each channel, we must be able to update both registers together.
Add a second set of register fields to struct snd_soc_dapm_update, and
update the DAPM control writeback (put) callbacks to support this.
For codecs that use custom events which call into DAPM to do updates,
also clear struct snd_soc_dapm_update before using it, so the second
set of fields remains clean.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a build error as below which appeared after merging
branch fix/samsung and also proper error messages are restored.
sound/soc/samsung/s3c24xx-i2s.c: In function ‘s3c24xx_iis_dev_probe’:
sound/soc/samsung/s3c24xx-i2s.c:444:8: error: ‘pdata’ undeclared (first use in this function)
sound/soc/samsung/s3c24xx-i2s.c:444:8: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes issues introduced in commit 73f5dfc683
"ASoC: samsung: get access to DMA engine early to defer probe properly"
and indicated by a following compilation warning:
CC [M] sound/soc/samsung/spdif.o
sound/soc/samsung/spdif.c: In function ‘spdif_probe’:
sound/soc/samsung/spdif.c:419:6: warning: ‘filter’ may be used uninitialized
in this function [-Wuninitialized]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AC97 drivers are broken and it seems these have not been used
for a long time. This patch removes the unused code, i.e. Samsung
SoC AC97 controller driver and related machine drivers:
ln2440sbc_alc650, smdk2443_wm9710, smdk_wm9713.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to report the resource request error in
the driver as it is already handled within devm_ioremap_resource().
While at it also drop a redundant variable initialization.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This simplifies the code a bit and removes a hard coded IO memory
region size.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the current probe function the GPIO is acquired after the codec's
bus clock is enabled. However if it fails to acquire the GPIO due to
a deferred probe, it does not disable the bus clock before bailing out.
This would result in the clock being enabled multiple times.
Move the code that enables the bus clock after the part that gets the
GPIO, maintaining a separation between resource acquisition and device
enablement in the probe function.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleans up usage of wrdma_ch and rdma_ch variables into a
common variable dma_ch, As there is no real use of tracking the dma
channel in two different variables based on stream direction.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds module licence to lpass-cpu driver, without this
patch lpass-cpu module would taint with below error:
snd_soc_lpass_cpu: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
snd_soc_lpass_cpu: Unknown symbol regmap_write (err 0)
snd_soc_lpass_cpu: Unknown symbol devm_kmalloc (err 0)
...
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes lpass-platform driver which was broken in v4.9-rc1.
lpass_pcm_data data structure holds information specific to stream.
Holding a single private pointer to it in global lpass_data
will not work, because it would be overwritten by for each pcm instance.
This code was breaking playback when we have both playback and capture
pcm streams, as playback settings are over written by capture settings.
Fix this by moving channel allocation logic out of pcm_new to pcm_open
so that we can store the stream specific information in private_data of
snd_pcm_runtime.
Fixes: 6adcbdcd4b ("ASoC: lpass-platform: don't use snd_soc_pcm_set_drvdata()")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When sun4i_codec_create_card fails, we do not assign a proper error
code to the return value. The return value would be 0 from the previous
function call, or we would have bailed out sooner. This would confuse
the driver core into thinking the device probe succeeded, when in fact
it didn't, leaving various devres based resources lingering.
Make the create_card function pass back a meaningful error code, and
assign it to the return value.
Fixes: 45fb6b6f2a ("ASoC: sunxi: add support for the on-chip codec on
early Allwinner SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/wm8580.c:988:33: warning:
symbol 'wm8580_data' was not declared. Should it be static?
sound/soc/codecs/wm8580.c:992:33: warning:
symbol 'wm8581_data' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for old version 4 of manifest.
Topology ABI v5 added new fields to manifest while user space may still
uses v4. So kernel will check the ABI version by comparing the object
size. If user space uses v4 of manifest, kernel will create a latest
version of manifest from the old one, and use the new one internally and
free it later.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mono ADC Capture Switch control is missing in the driver. So, add it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove cpu/codec pointer check from asoc_simple_card_canonicalize_dailink()
This is verbose check, and will be issue if CPU name was created by
fmt_single_name() on simple-scu-card.c.
see also asoc_simple_card_canonicalize_cpu()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple sound card family are using very similar style, but because of its
historical reason, there are small differences. For example pointer style,
function name, caller postion etc...
This patch synchronizes style to other simple card family so that be enable
to easy reviewing.
This patch uses dai_link/dai_props instead of links/props.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple sound card family are using very similar style, but because of its
historical reason, there are small differences. For example pointer style,
function name, caller postion etc...
This patch synchronized simple card style to other simple card family
This patch renames asoc_simple_card_priv to simple_card_data,
same as other simple card family.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple sound card family are using very similar style, but because of its
historical reason, there are small differences. For example pointer style,
function name, caller postion etc...
This patch synchronized simple card style to other simple card family
Current simple-scu-card function naming is different from other simple card
family. And related to it, the necessary operation position is also
different. This patch synchronize these to other simple card family.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current register name of "SSICKR" was came from R-Car Gen1
which is very old style. It is called as "BRGCKR" on R-Car Gen2/Gen3.
Let's rename it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controllers support power modes which can't communicate using IPC.
So add a callback to check and wake DSP before sending IPC and then put
to sleep if it is in these power modes.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a DAI specifies "#sound-dai-cells = <0>" in device-tree then
hdmi_of_xlate_dai_name() will be called with zero args, which it isn't
implemented to cope with. The resulting use of an uninitialised variable
for the id will usually result in an error like:
asoc-simple-card sound: parse error -11
asoc-simple-card: probe of sound failed with error -11
Fix this by using and id of zero if no arg is provided.
Fixes: 9731f82d60 ("ASoC: hdmi-codec: enable multi probe for same device")
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC Samsung sub-drivers tried to get access to their DMA engine
controllers as a last step in driver probe. If a DMA engine was not
available yet, samsung_asoc_dma_platform_register() function ended in
-EPROBE_DEFER, but the driver already registered its component to ASoC
core. This patch moves samsung_asoc_dma_platform_register() call before
registering any components, to the common place, where driver was gathering
all needed resources.
In case of Samsung Exynos i2s driver the issue was even worse. The driver
managed already to register its secondary DAI platform device before
even getting the DMA engine access. That together with -EPROBE_DEFER error
code from samsung_i2s_probe() immediately triggered another round of
deferred probe retry and in turn endless loop of driver probing.
This patch fixes broken boot on Odroid XU3 and other Exynos5422-based
boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch is adding debug information related to SST FW version.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
da7219 output (for headset capture) should be set to high-impedance when
not in use, since it will otherwise interfere with output from other
codecs attached to the same DAI.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPIB is read currently from a buffer position in memory (indicated by
the registers DPIB[U|L]BASE).Driver reads the position buffer on BDL
completion interrupts to report the DMA position. But the BDL completion
interrupt only indicates the last DMA transfer of the buffer is
completed at the Intel HD Audio subsystem boundary. The periodic DMA
Position-in-Buffer writes may be scheduled at the same time or later
than the MSI and does not guarantee to reflect the position of the last
buffer that was transferred.
Whereas DPIB register in HDA space(vendor specific register indicated by
SDxDPIB) reflects the actual data that is transferred. Hence update the
position based on DPIB for playback.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's difficult to guess from bunch of "ret=-121" errors what driver and
device actually caused them. Since struct i2c_client has the dev pointer
use that for dev_err() with meaningful error message.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI codec is required to be powered up before controller initialization
for successful enumeration of codec. If the probe fails it needs to be
powered off to balance the power state of HDMI codec.
This fix balances the reference count in the error path before turning
off the codec.
Reported-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4c5d146929 ("ASoC: max98504: Add max98504 speaker amplifier
driver") added new max98504, but this patch didn't add it to
SND_SOC_ALL_CODECS. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SRC (= Sampling Rate Converter) is supporting
SYNC mode and ASYNC mode. Current src.c cares SRC if FIN != FOUT.
Here, SYNC mode will be used for tweak, so it will be used
even FIN = FOUT. This patch enables SRC sync in such situation
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Yuichi Takagi <yuichi.takagi.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound SSIU has SSI_SYS_STATUS register whick will
be changed if over/under run was occurred.
Current rsnd driver is handling over/under run error on SSI/SRC,
but doesn't on SSIU.
HW guys can't guarantee correct behavior if it already had error bit
on status register when it start.
Thus, it should be cleared every start timing. This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SCU_SYS_STATUSx is the register that writing 1 initializes the bit,
and writing 0 is ignored. So, it should use rsnd_mod_write()
instead of rsnd_mod_bset(), otherwise all bit will be cleared.
Thanks Shimoda-san
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car Gen1 didn't have SSIU IP, and it was part of SRU.
In Gen2, SSIU was created and it has original register.
Let's cleanup rsnd_reg for SSIU, because this driver
doesn't support Gen1 SRU any more.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gen1 support had been removed. "Gen2 only" comment is
no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the compressed ops run on the platform side of things we should
really access the driver data through the platform pointer rather than
the CODEC pointer. As the compressed DAIs in our systems always connect
our CODEC to our platform this has never been an issue, but should still
be corrected. Additionally it clears the way for future core refactoring
work.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 31833ead95 ("ASoC: arizona: Move request of speaker IRQs into bus probe")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is completely depends on CONFIG_OF
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some registers accesses are done in atomic context.
Enable fast io to use spinlock instead of mutex to protect access.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
stih416 is no more supported, clean associated code.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If 'IEC958 Playback Default' control is updated during playback,
Channel status needs to be set according to the runtime structure.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reset is common to player and reader, migrate function in sti_uniperif.c
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing error messages.
Propagate error of uni_reader_init and uni_reader_init.
Add return at end of dev_err strings.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a check for validity of one of ids in mxs_saif_probe(),
while array dereferece is made by the other id.
The patch adds the check for the second saif id.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
"*val" is a u64. It definitely looks like we intend to use the high 32
bits as well.
Fixes: 700a9a63f9 ("ASoC: Intel: Skylake: Add module instance id generation APIs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the DSP compressed data IRQ from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the speaker thermal event IRQs from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CS35L34_CHIP_ID is not a register address, it's the value read from
CS35L34_DEVID_AB/CD/E registers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pr_err() are replaced with dev_err() so information about
device the error logs refer to is also included.
pr_debug() at beginning of each function are removed
as they are likely very rarely used and can always be
added again when doing any serious debugging.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the s3c24xx-dma is converted to use DMA map we can rely on the
DMA subsystem to match DMA channels and slave devices, rather than
passing DMA details from platform_data.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 194c7dea00
"ASoC: dmaengine: add custom DMA config to snd_dmaengine_pcm_config"
custom DMA channels can be also specified in chan_names[] field of
struct snd_dmaengine_pcm_config. This patch removes chan_name field
of struct snd_dmaengine_dai_dma_data as it is now unused.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates the I2S drivers to always use chan_names[] field
of struct snd_dmaengine_pcm_config for specifying DMA channel names,
rather than using struct snd_dmaengine_dai_dma_data.
This allows us to subsequently drop the
SND_DMAENGINE_PCM_FLAG_CUSTOM_CHANNEL_NAME flag, now when the last
use of that flag is removed.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't manually enable cache_bypass for reading the ID registers they
don't have a default anyway so the first read will always hit the
hardware. The old code worked this is simply the more standard way
to implement this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than manually enabling cache bypass when reading the ID registers
simply remove the default which will cause the first read to go to the
hardware. The old code worked this is simply the more standard way to
implement this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than manually enabling cache bypass when reading the ID registers
simply remove the default which will cause the first read to go to the
hardware. The old code worked this is simply the more standard way to
implement this. There is a comment included in the code that claims the
chip ID register also contains the right input volume, however this is
clearly not the case from the rest of the driver. Further investigation
reveals exactly the same comment in the wm8962 driver, where this is the
case, so this is almost certainly a copy and paste error from when the
driver was created.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver requests DMA channel when .probe timing,
and release it when .remove timing. And use DMA on .start/.stop
But, Audio DMAC power ON was handled when request timing (= .probe),
and power OFF was when release timing (= .remove).
This means Audio DMAC power is always ON during driver was enabled.
To fixup this issue, it should request/release DMA channel on each
playback/recorde timing.
But, DMA channel request/release function uses mutex lock inside.
This means it will breaks current spinlock's interrupt protect.
To solve this issue, DMA channel request/release function needs to
be called from non-spinlock area. This patch adds its callback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_dmaen_start() is calling of_node_put() for np,
but it is not needed if it goes through this loop.
This patch tidyup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA mod is now connected to stream via rsnd_dai_connect().
This means DMA mod can use .remove for its clearance.
rsnd_dma_detach() is no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI will use DMA mode, and migh be fallback to PIO mode.
Using devm_request_irq() makes its operation more complex when
it fallbacks to PIO mode.
Let's use manual request_irq()/free_irq()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver is based on DeviceTree, and no one is
using this driver from non DT. Non-DT support is no longer needed.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent rewrite of the sequencer time accounting using timespec64
in the commit [3915bf294652: ALSA: seq_timer: use monotonic times
internally] introduced a bad regression. Namely, the time reported
back doesn't increase but goes back and forth.
The culprit was obvious: the delta is stored to the result (cur_time =
delta), instead of adding the delta (cur_time += delta)!
Let's fix it.
Fixes: 3915bf2946 ('ALSA: seq_timer: use monotonic times internally')
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177571
Reported-by: Yves Guillemot <yc.guillemot@wanadoo.fr>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the DMIC that needs time to initial after the MCLK is provided, the
field of delay time is implemented by the platform data.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gather all driver's private variables in common data structure
and allocate the data structure dynamically.
Also unused ENFORCE_RATES symbol and local variable (leftovers
from an erroneous rebase) are removed.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASRock B150M Pro4/D3 mobo with ALC892 codec doesn't seem to provide
proper pins for the surround outputs, hence we need to specify the
pincfgs manually with a couple of other corrections.
Reported-and-tested-by: Benjamin Valentin <benpicco@googlemail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- first slice of the gvt device model (Zhenyu et al)
- compression support for gpu error states (Chris)
- sunset clause on gpu errors resulting in dmesg noise telling users
how to report them
- .rodata diet from Tvrtko
- switch over lots of macros to only take dev_priv (Tvrtko)
- underrun suppression for dp link training (Ville)
- lspcon (hmdi 2.0 on skl/bxt) support from Shashank Sharma, polish
from Jani
- gen9 wm fixes from Paulo&Lyude
- updated ddi programming for kbl (Rodrigo)
- respect alternate aux/ddc pins (from vbt) for all ddi ports (Ville)
* tag 'drm-intel-next-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (227 commits)
drm/i915: Update DRIVER_DATE to 20161024
drm/i915: Stop setting SNB min-freq-table 0 on powersave setup
drm/i915/dp: add lane_count check in intel_dp_check_link_status
drm/i915: Fix whitespace issues
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_ddc_pin for all DDI ports
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: Remove WaEnableYV12BugFixInHalfSliceChicken7
drm/i915: KBL - Recommended buffer translation programming for DisplayPort
drm/i915: Move down skl/kbl ddi iboost and n_edp_entires fixup
drm/i915: Add a sunset clause to GPU hang logging
drm/i915: Stop reporting error details in dmesg as well as the error-state
drm/i915/gvt: do not ignore return value of create_scratch_page
drm/i915/gvt: fix spare warnings on odd constant _Bool cast
drm/i915/gvt: mark symbols static where possible
drm/i915/gvt: fix sparse warnings on different address spaces
drm/i915/gvt: properly access enabled intel_engine_cs
drm/i915/gvt: Remove defunct vmap_batch()
drm/i915/gvt: Use common mapping routines for shadow_bb object
drm/i915/gvt: Use common mapping routines for indirect_ctx object
...
Unfortunately, I seem to have missed a case where an IRQ safe spinlock was
required, in samsung_i2s_dai_remove, when I fixed up the other calls in
this patch:
316fa9e09a ("ASoC: samsung: Use IRQ safe spin lock calls")
This causes a lockdep warning when unbinding and rebinding the audio card:
[ 104.357664] CPU0 CPU1
[ 104.362174] ---- ----
[ 104.366692] lock(&(&pri_dai->spinlock)->rlock);
[ 104.371372] local_irq_disable();
[ 104.377283] lock(&(&substream->self_group.lock)->rlock);
[ 104.385259] lock(&(&pri_dai->spinlock)->rlock);
[ 104.392469] <Interrupt>
[ 104.395072] lock(&(&substream->self_group.lock)->rlock);
[ 104.400710]
[ 104.400710] *** DEADLOCK ***
Fixes: ce8bcdbb61 ("ASoC: samsung: i2s: Protect more registers with a spinlock")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ak4641 driver only has a few register defines. As they are only used in
the one main driver file there is not really a need to keep them in a
separate header.
Moving them to the main source file allows to remove the now empty header
file completely.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The last user was removed in commit 4f534777c1 ("ASoC: ak4641: Convert to
direct regmap API usage").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. This driver was merged after the change of DAIs are
matched was made and the IDs were never used and presumably never will be,
so remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The es8328 drivers seems to have used the wm8753 driver as a template. Its
header file contains a few defines that are copied verbatim from the wm8753
header that do not really apply to this driver and are unused. So remove
those defines. This seems safe as they deal with PLL and clock divider
settings and the es8328 driver neither implements a set_pll() nor a
set_clkdiv() callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. This particular ID was never used and presumably never
will be, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
This also means the wm9705.h file no longer has any content and can be
removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. These particular IDs were never used and presumably
never will be, so remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
This also means the wm9712.h file no longer has any content and can be
removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o files is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
8748 1024 0 9772 262c sound/soc/fsl/fsl-asoc-card.o
8812 952 0 9764 2624 sound/soc/fsl/fsl-asoc-card.o
text data bss dec hex filename
4165 264 8 4437 1155 sound/soc/fsl/imx-wm8962.o
4229 200 8 4437 1155 sound/soc/fsl/imx-wm8962.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o files is shown by the following output
of the size command, first before then after the transformation:
text data bss dec hex filename
4500 696 0 5196 144c sound/soc/generic/simple-card.o
4564 632 0 5196 144c sound/soc/generic/simple-card.o
text data bss dec hex filename
3018 608 0 3626 e2a sound/soc/generic/simple-scu-card.o
3074 544 0 3618 e22 sound/soc/generic/simple-scu-card.o
text data bss dec hex filename
4148 2448 768 7364 1cc4 sound/soc/intel/boards/bdw-rt5677.o
4212 2384 768 7364 1cc4 sound/soc/intel/boards/bdw-rt5677.o
text data bss dec hex filename
5403 4628 384 10415 28af sound/soc/intel/boards/bxt_da7219_max98357a.o
5531 4516 384 10431 28bf sound/soc/intel/boards/bxt_da7219_max98357a.o
text data bss dec hex filename
5275 4496 384 10155 27ab sound/soc/intel/boards/bxt_rt298.o
5403 4368 384 10155 27ab sound/soc/intel/boards/bxt_rt298.o
text data bss dec hex filename
10017 2344 48 12409 3079 sound/soc/intel/boards/bytcr_rt5640.o
10145 2232 48 12425 3089 sound/soc/intel/boards/bytcr_rt5640.o
text data bss dec hex filename
3719 2356 0 6075 17bb sound/soc/intel/boards/bytcr_rt5651.o
3847 2244 0 6091 17cb sound/soc/intel/boards/bytcr_rt5651.o
text data bss dec hex filename
3598 2392 0 5990 1766 sound/soc/intel/boards/cht_bsw_max98090_ti.o
3726 2280 0 6006 1776 sound/soc/intel/boards/cht_bsw_max98090_ti.o
text data bss dec hex filename
5343 3624 16 8983 2317 sound/soc/intel/boards/cht_bsw_rt5645.o
5471 3496 16 8983 2317 sound/soc/intel/boards/cht_bsw_rt5645.o
text data bss dec hex filename
4662 2592 384 7638 1dd6 sound/soc/intel/boards/cht_bsw_rt5672.o
4790 2464 384 7638 1dd6 sound/soc/intel/boards/cht_bsw_rt5672.o
text data bss dec hex filename
1595 2528 0 4123 101b sound/soc/intel/boards/haswell.o
1659 2472 0 4131 1023 sound/soc/intel/boards/haswell.o
text data bss dec hex filename
6272 4760 416 11448 2cb8 sound/soc/intel/boards/skl_nau88l25_max98357a.o
6464 4568 416 11448 2cb8 sound/soc/intel/boards/skl_nau88l25_max98357a.o
text data bss dec hex filename
7075 4888 416 12379 305b sound/soc/intel/boards/skl_nau88l25_ssm4567.o
7267 4696 416 12379 305b sound/soc/intel/boards/skl_nau88l25_ssm4567.o
text data bss dec hex filename
5659 4496 384 10539 292b sound/soc/intel/boards/skl_rt286.o
5787 4368 384 10539 292b sound/soc/intel/boards/skl_rt286.o
text data bss dec hex filename
1721 2048 0 3769 eb9 sound/soc/kirkwood/armada-370-db.o
1769 1976 0 3745 ea1 sound/soc/kirkwood/armada-370-db.o
text data bss dec hex filename
1363 1792 0 3155 c53 sound/soc/mxs/mxs-sgtl5000.o
1427 1728 0 3155 c53 sound/soc/mxs/mxs-sgtl5000.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o files is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
3143 1888 384 5415 1527 sound/soc/tegra/tegra_alc5632.o
3191 1840 384 5415 1527 sound/soc/tegra/tegra_alc5632.o
text data bss dec hex filename
3672 2176 768 6616 19d8 sound/soc/tegra/tegra_max98090.o
3720 2128 768 6616 19d8 sound/soc/tegra/tegra_max98090.o
text data bss dec hex filename
2770 1856 384 5010 1392 sound/soc/tegra/tegra_rt5640.o
2818 1808 384 5010 1392 sound/soc/tegra/tegra_rt5640.o
text data bss dec hex filename
4412 2176 768 7356 1cbc sound/soc/tegra/tegra_rt5677.o
4460 2128 768 7356 1cbc sound/soc/tegra/tegra_rt5677.o
text data bss dec hex filename
2442 1536 0 3978 f8a sound/soc/tegra/tegra_sgtl5000.o
2490 1480 0 3970 f82 sound/soc/tegra/tegra_sgtl5000.o
text data bss dec hex filename
2105 1536 0 3641 e39 sound/soc/tegra/tegra_wm8753.o
2153 1480 0 3633 e31 sound/soc/tegra/tegra_wm8753.o
text data bss dec hex filename
3755 1888 768 6411 190b sound/soc/tegra/tegra_wm8903.o
3803 1840 768 6411 190b sound/soc/tegra/tegra_wm8903.o
text data bss dec hex filename
2121 1536 0 3657 e49 sound/soc/tegra/trimslice.o
2169 1480 0 3649 e41 sound/soc/tegra/trimslice.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o file is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
1420 512 0 1932 78c sound/soc/qcom/storm.o
1484 456 0 1940 794 sound/soc/qcom/storm.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o files is shown by the following output
of the size command, first before then after the transformation:
text data bss dec hex filename
5027 2488 416 7931 1efb sound/soc/rockchip/rk3399_gru_sound.o
5219 2312 416 7947 1f0b sound/soc/rockchip/rk3399_gru_sound.o
text data bss dec hex filename
3499 1648 384 5531 159b sound/soc/rockchip/rockchip_max98090.o
3563 1584 384 5531 159b sound/soc/rockchip/rockchip_max98090.o
text data bss dec hex filename
3455 1536 384 5375 14ff sound/soc/rockchip/rockchip_rt5645.o
3519 1480 384 5383 1507 sound/soc/rockchip/rockchip_rt5645.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o file is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
2611 1536 0 4147 1033 sound/soc/atmel/atmel_wm8904.o
2675 1480 0 4155 103b sound/soc/atmel/atmel_wm8904.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o file is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
3865 2784 384 7033 1b79 sound/soc/intel/boards/broadwell.o
3929 2720 384 7033 1b79 sound/soc/intel/boards/broadwell.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a power saving mechanism in rt5670. It will turn off some
unused power when MCLK is not present. We call that "MCLK detection"
and it should be enabled by default.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a power saving mechanism in rt5640. It will turn off some
unused power when MCLK is not present. We call that "MCLK detection"
and it should be enabled by default.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I rand into a new build error with SND_MMP_SOC_BROWNSTONE:
warning: (SND_MMP_SOC_BROWNSTONE && SND_SOC_SAMSUNG_SMDK_WM8994 && SND_SOC_SMDK_WM8994_PCM && SND_SOC_LITTLEMILL) selects MFD_WM8994 which has unmet direct dependencies (HAS_IOMEM && I2C)
drivers/mfd/wm8994-core.c:688:1: error: data definition has no type or storage class [-Werror]
drivers/mfd/wm8994-core.c:688:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
I don't see why this never showed up before, as the dependency seems to
have been missing since the symbol was first introduced several years
ago. This adds a dependency like the other drivers have.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warning:
sound/soc/rockchip/rk3399_gru_sound.c:41:14: warning:
symbol 'rt5514_dmic_delay' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Smatch reports below warnings:
bxt_da7219_max98357a.c:352:9: warning: obsolete array initializer,
use C99 syntax
An earlier commit cleaned up similar warnings, however, a recent
commit 43c02ede76 ("ASoC: Intel: Add DMIC channel constraint for
bxt machine") re-introduced the older initializer style. So fix
this warning to make the code consistent.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the wm8581 codec to the wm8580 driver.
The wm8581 codec hardware adds a fourth DAC and otherwise is
compatible with the wm8580 codec.
of_device_id data is used to allow the driver to select the
suitable DAC count specified in the device tree codec selection.
The wm8580_driver_data struct is used to store the number of DACs.
The snd_soc_dai_driver no longer lists the channels_max for the
playback substream. This variable is set during the i2c probe
from the of_device_id supplied wm8580_driver_data struct.
With knowledge of the number of DACs in use, the DAC4 controls,
widgets and routes are added as required for DAC4.
The device tree documentation for the wm8580 is altered to list
the wm8581 codec support, as is the Kconfig file.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, we have for_each_rsnd_mod(), let's use it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using too complex macro for for-loop of each mod.
rsnd_dai_call() is especially defined as very complex macro.
It is easier to read just a little bit by using for_each_rsnd_mod_xxx()
and new rsnd_status_update()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using too complex macro for for-loop of each mod.
In order to simplify this issue, this patch adds new rsnd_mod_next()
which is non-macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 1a5658c213 ("ASoC: rsnd: count .probe/.remove for
rsnd_mod_call()") solved multi-resource-free issue, by putting
.probe/.remove under count control. But,it breaks sound mixing case
(if it was used under DPCM). In such case, it uses MIXn/DVCn/SSIn,
and these should be always probed.
This patch reverted above patch, and solved the same issue by
modifing _rsnd_kctrl_remove() function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a power saving mechanism in rt5660. It will turn off some
unused power when MCLK is not present. We call that "MCLK detection"
and it should be enabled by default.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to multi codec, as the msm8916 codec is now
split into two codecs, Analog and Digital.
Also update the bindings and example to show that the card supports
multicodec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts(Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Digital part of the Codec which is integrated
into Application Processor.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts (Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Analog part of the Codec which is integrated
into PMIC PM8916.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_probe() releases a runtime pm ref unconditionally wheras
skl_remove() acquires one only if the device is wakeup capable.
Thus if the device is not wakeup capable, unloading and reloading
the module will result in the refcount being decreased below 0.
Fix it.
Fixes: d8c2dab838 ("ASoC: Intel: Add Skylake HDA audio driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "rt5668" codec supported in this driver is actually a revision
of "rt5663". So the patch is renamed to "rt5663 v2"
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove
the wrappers.
Also use snd_soc_update_bits() where appropriate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the wm9712 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the wm9705
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
enable the source clocks for FLLs as they are powered up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
gating the source clocks for SYSCLK/ASYNCCLK when they are configured
to come directly from an MCLK pin.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt298_jack_detect may be called before card is instantiated. And
snd_soc_dapm_force_enable_pin will not work in that case. So, update
bit manually by regmap_update_bits.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove
the wrappers. Also use snd_soc_update_bits() were appropriate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the wm9712 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the wm9712
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates Jack type bitmask to include SND_JACK_LINEOUT while
creating a new jack, so that LINEOUT events are reported properly.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of the Cirrus Logic cs35l34 8V boosted class D
amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
They uses the codec ALC255, and have the different pin cfg definition
from the ones in the existing pin quirk table. Now adding them into
the table to fix the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some elements in hr are not cleared before being copied to user space,
leaking kernel heap memory to user space. For example, this happens in
the error handling code for the HPI_ADAPTER_DELETE case. Zero the memory
before it's copied.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have a new Dell laptop model which uses ALC295, the pin definition
is different from the existing ones in the pin quirk table, to fix the
headset mic detection and mic mute led's problem, we need to add the
new pin defintion into the pin quirk table.
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 49d9e77e72 ("ALSA: hda - Fix system panic when DMA > 40 bits
for Nvidia audio controllers") simply disabled any DMA exceeding 32
bits for NVidia devices, even though they are capable of performing
DMA up to 40 bits. On some architectures (such as arm64), system memory
is not guaranteed to be 32-bit addressable by PCI devices, and so this
change prevents NVidia devices from working on platforms such as AMD
Seattle.
Since the original commit already mentioned that up to 40 bits of DMA
is supported, and given that the code has been updated in the meantime
to support a 40 bit DMA mask on other devices, revert commit 49d9e77e72
and explicitly set the DMA mask to 40 bits for NVidia devices.
Fixes: 49d9e77e72 ('ALSA: hda - Fix system panic when DMA > 40 bits...')
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a few trivial small fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJYAfDbAAoJEGwxgFQ9KSmkTe0QAI6QGGDDQH6hz+4Gp9pTsF71
+fHcuAVZWgd5T5EAQq+9Av2wiVtgl1Oc5J7bRooVfJYswQRx43xE0GKHkDwCYBqU
HeiT+jpsv2sZdVVuG/t6vWXFyIMsQ0CJ8dW+i+oJ23Etdq+vb1TE1IlHk76iJlqX
xX+ko/xrVksOndUHkgjn554edmIkpSKN/TDs9lZ/NdFkg1LnLR+r0ecgshUikBau
jRqc3m8Fm5uWMtqosqWrjHQwG/1FJp6DVIcyJOYBF18Fnnmmh+gIKPEa0yUq0bpg
Fbph1ANN2nYrbUK6wZfhgFBs1atACswrvXb81B2anekjz7Br1i271L7i+k7XexG9
A14/+CHgXDCAB888H8gg0H4tx7YGxXC3PhCO1b3dpX5My6M/C/52oFERjAG9a1jE
DJLNjfgTXFsJxOP0RvBOv1doi4Npv9pxjt01MwkszMlisd1FBhvKUPDeRBQuHCCi
dbKU26WVi5JlWKINnh82348DJ0qhES82oFIyGdxX3zgIuMwgOxeSOGLKB3C/p0OM
SWYB1DvOOlHoA0sgqp0Ggkh002vRSTo/5ZW2DGvgkfaVnHCNjjp67XiMhzzXG3dg
d5mjlSlmiADlWUj5mBjZFvFc1c8Hm9xcRpi138fnUvWhKfVkcrA9dwbdupkPzc2S
7MiI7GA8+LckjEIHKuf3
=CjWZ
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few trivial small fixes"
* tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: line6: fix a crash in line6_hwdep_write()
ALSA: seq: fix passing wrong pointer in function call of compatibility layer
ALSA: hda - Fix a failure of micmute led when having multi adcs
ALSA: line6: Fix POD X3 Live audio input
We increment "i" before printing the debug statement. That makes it
the wrong sleep_time[] information and Smatch complains that the last
increment could be beyond the end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error checking here is messed up so we could end up dereferencing
-EFAULT.
Fixes: a16039cbf1 ('ALSA: line6: Add hwdep interface to access the POD control messages')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a fix for Linux 4.9-rc1.
In former commit, a function call of compatibility layer for ALSA sequencer
core was obsoleted by an alternative. Although, the alternative gets a
pointer to kernel stack due to mis-programming. As a result, ALSA sequencer
core unexpectedly refers over kernel stack.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 8ce8eb601c ("ALSA: seq: add an alternative way to handle ioctl requests")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a Dell laptop, there is no global adcs for all input devices, so
the input devices use the different adc, as a result, dyn_adc_switch
is set to true.
In this situation, it is safe to control the micmute led according to
user's choice of muting/unmuting the current input device, since only
current input device path is active, while other input device paths
are inactive and powered down.
Fixes: 00ef99408b ('ALSA: hda - add mic mute led hook for dell machines')
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's been over two months, git definitely lost it's marbles. Conflicts
resolved by picking our version, plus manually checking the diff with
the parent in drm-intel-next-queued to make sure git didn't do
anything stupid. It did, so I removed 2 occasions where it
double-inserted a bit of code. The diff is now just
- kernel-doc changes
- drm format/name changes
- display-info changes
so looks all reasonable.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mismatching stream names in DAPM route and widget definitions are
causing compilation errors. Fixing these names allows the cs4270
driver to compile and function.
[Errors must be at probe time not compile time -- broonie]
Signed-off-by: Murray Foster <mrafoster@gmail.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The Intel Haswell audio support fails to link if
CONFIG_SND_SOC_INTEL_SST_FIRMWARE is disabled:
sst-haswell-dsp.c: undefined reference to `sst_mem_block_register'
sst-haswell-dsp.c: undefined reference to `sst_mem_block_unregister_all'
sst-haswell-dsp.c: undefined reference to `sst_module_alloc_blocks'
sst-haswell-dsp.c: undefined reference to `sst_module_free'
sst-haswell-dsp.c: undefined reference to `sst_module_new'
sst-haswell-pcm.c: undefined reference to `sst_module_get_from_id'
sst-haswell-pcm.c: undefined reference to `sst_module_runtime_restore'
sst-haswell-pcm.c: undefined reference to `sst_module_runtime_save'
ERROR: "sst_block_alloc_scratch" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_block_free_scratch" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_dma_copyfrom" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_dma_copyto" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_dma_get_channel" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_dma_put_channel" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_free" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_get_offset" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_new" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_fw_free_all" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_fw_new" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_fw_reload" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_fw_unload" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_module_runtime_alloc_blocks" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_module_runtime_get_from_id" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_module_runtime_new" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
This moves the 'select' statement from two of the three haswell based users
into the line that is used by all of them, so make it harder to get wrong
and to fix the existing randconfig regressions.
Fixes: 2d995e5dc2 ("ASoC: Intel: boards: Add bdw-rt5677 machine driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit c039aaa77a was incomplete,
missing part of the setup for Live. This makes also audio input work,
in addition to audio output.
Fixes: c039aaa77a
Reported-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Highlights:
- Major rework of Book3S 64-bit exception vectors (Nicholas Piggin)
- Use gas sections for arranging exception vectors et. al.
- Large set of TM cleanups and selftests (Cyril Bur)
- Enable transactional memory (TM) lazily for userspace (Cyril Bur)
- Support for XZ compression in the zImage wrapper (Oliver O'Halloran)
- Add support for bpf constant blinding (Naveen N. Rao)
- Beginnings of upstream support for PA Semi Nemo motherboards (Darren Stevens)
Fixes:
- Ensure .mem(init|exit).text are within _stext/_etext (Michael Ellerman)
- xmon: Don't use ld on 32-bit (Michael Ellerman)
- vdso64: Use double word compare on pointers (Anton Blanchard)
- powerpc/nvram: Fix an incorrect partition merge (Pan Xinhui)
- powerpc: Fix usage of _PAGE_RO in hugepage (Christophe Leroy)
- powerpc/mm: Update FORCE_MAX_ZONEORDER range to allow hugetlb w/4K (Aneesh Kumar K.V)
- Fix memory leak in queue_hotplug_event() error path (Andrew Donnellan)
- Replay hypervisor maintenance interrupt first (Nicholas Piggin)
Cleanups & features:
- Sparse fixes/cleanups (Daniel Axtens)
- Preserve CFAR value on SLB miss caused by access to bogus address (Paul Mackerras)
- Radix MMU fixups for POWER9 (Aneesh Kumar K.V)
- Support for setting used_(vsr|vr|spe) in sigreturn path (for CRIU) (Simon Guo)
- Optimise syscall entry for virtual, relocatable case (Nicholas Piggin)
- Optimise MSR handling in exception handling (Nicholas Piggin)
- Support for kexec with Radix MMU (Benjamin Herrenschmidt)
- powernv EEH fixes (Russell Currey)
- Suprise PCI hotplug support for powernv (Gavin Shan)
- Endian/sparse fixes for powernv PCI (Gavin Shan)
- Defconfig updates (Anton Blanchard)
- Various performance optimisations (Anton Blanchard)
- Align hot loops of memset() and backwards_memcpy()
- During context switch, check before setting mm_cpumask
- Remove static branch prediction in atomic{, 64}_add_unless
- Only disable HAVE_EFFICIENT_UNALIGNED_ACCESS on POWER7 little endian
- Set default CPU type to POWER8 for little endian builds
- KVM: PPC: Book3S HV: Migrate pinned pages out of CMA (Balbir Singh)
- cxl: Flush PSL cache before resetting the adapter (Frederic Barrat)
- cxl: replace loop with for_each_child_of_node(), remove unneeded of_node_put() (Andrew Donnellan)
- Fix HV facility unavailable to use correct handler (Nicholas Piggin)
- Remove unnecessary syscall trampoline (Nicholas Piggin)
- fadump: Fix build break when CONFIG_PROC_VMCORE=n (Michael Ellerman)
- Quieten EEH message when no adapters are found (Anton Blanchard)
- powernv: Add PHB register dump debugfs handle (Russell Currey)
- Use kprobe blacklist for exception handlers & asm functions (Nicholas Piggin)
- Document the syscall ABI (Nicholas Piggin)
- MAINTAINERS: Update cxl maintainers (Michael Neuling)
- powerpc: Remove all usages of NO_IRQ (Michael Ellerman)
Minor cleanups:
- Andrew Donnellan, Christophe Leroy, Colin Ian King, Cyril Bur, Frederic Barrat,
Pan Xinhui, PrasannaKumar Muralidharan, Rui Teng, Simon Guo.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jnn8
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Major rework of Book3S 64-bit exception vectors (Nicholas Piggin)
- Use gas sections for arranging exception vectors et. al.
- Large set of TM cleanups and selftests (Cyril Bur)
- Enable transactional memory (TM) lazily for userspace (Cyril Bur)
- Support for XZ compression in the zImage wrapper (Oliver
O'Halloran)
- Add support for bpf constant blinding (Naveen N. Rao)
- Beginnings of upstream support for PA Semi Nemo motherboards
(Darren Stevens)
Fixes:
- Ensure .mem(init|exit).text are within _stext/_etext (Michael
Ellerman)
- xmon: Don't use ld on 32-bit (Michael Ellerman)
- vdso64: Use double word compare on pointers (Anton Blanchard)
- powerpc/nvram: Fix an incorrect partition merge (Pan Xinhui)
- powerpc: Fix usage of _PAGE_RO in hugepage (Christophe Leroy)
- powerpc/mm: Update FORCE_MAX_ZONEORDER range to allow hugetlb w/4K
(Aneesh Kumar K.V)
- Fix memory leak in queue_hotplug_event() error path (Andrew
Donnellan)
- Replay hypervisor maintenance interrupt first (Nicholas Piggin)
Various performance optimisations (Anton Blanchard):
- Align hot loops of memset() and backwards_memcpy()
- During context switch, check before setting mm_cpumask
- Remove static branch prediction in atomic{, 64}_add_unless
- Only disable HAVE_EFFICIENT_UNALIGNED_ACCESS on POWER7 little
endian
- Set default CPU type to POWER8 for little endian builds
Cleanups & features:
- Sparse fixes/cleanups (Daniel Axtens)
- Preserve CFAR value on SLB miss caused by access to bogus address
(Paul Mackerras)
- Radix MMU fixups for POWER9 (Aneesh Kumar K.V)
- Support for setting used_(vsr|vr|spe) in sigreturn path (for CRIU)
(Simon Guo)
- Optimise syscall entry for virtual, relocatable case (Nicholas
Piggin)
- Optimise MSR handling in exception handling (Nicholas Piggin)
- Support for kexec with Radix MMU (Benjamin Herrenschmidt)
- powernv EEH fixes (Russell Currey)
- Suprise PCI hotplug support for powernv (Gavin Shan)
- Endian/sparse fixes for powernv PCI (Gavin Shan)
- Defconfig updates (Anton Blanchard)
- KVM: PPC: Book3S HV: Migrate pinned pages out of CMA (Balbir Singh)
- cxl: Flush PSL cache before resetting the adapter (Frederic Barrat)
- cxl: replace loop with for_each_child_of_node(), remove unneeded
of_node_put() (Andrew Donnellan)
- Fix HV facility unavailable to use correct handler (Nicholas
Piggin)
- Remove unnecessary syscall trampoline (Nicholas Piggin)
- fadump: Fix build break when CONFIG_PROC_VMCORE=n (Michael
Ellerman)
- Quieten EEH message when no adapters are found (Anton Blanchard)
- powernv: Add PHB register dump debugfs handle (Russell Currey)
- Use kprobe blacklist for exception handlers & asm functions
(Nicholas Piggin)
- Document the syscall ABI (Nicholas Piggin)
- MAINTAINERS: Update cxl maintainers (Michael Neuling)
- powerpc: Remove all usages of NO_IRQ (Michael Ellerman)
Minor cleanups:
- Andrew Donnellan, Christophe Leroy, Colin Ian King, Cyril Bur,
Frederic Barrat, Pan Xinhui, PrasannaKumar Muralidharan, Rui Teng,
Simon Guo"
* tag 'powerpc-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (156 commits)
powerpc/bpf: Add support for bpf constant blinding
powerpc/bpf: Implement support for tail calls
powerpc/bpf: Introduce accessors for using the tmp local stack space
powerpc/fadump: Fix build break when CONFIG_PROC_VMCORE=n
powerpc: tm: Enable transactional memory (TM) lazily for userspace
powerpc/tm: Add TM Unavailable Exception
powerpc: Remove do_load_up_transact_{fpu,altivec}
powerpc: tm: Rename transct_(*) to ck(\1)_state
powerpc: tm: Always use fp_state and vr_state to store live registers
selftests/powerpc: Add checks for transactional VSXs in signal contexts
selftests/powerpc: Add checks for transactional VMXs in signal contexts
selftests/powerpc: Add checks for transactional FPUs in signal contexts
selftests/powerpc: Add checks for transactional GPRs in signal contexts
selftests/powerpc: Check that signals always get delivered
selftests/powerpc: Add TM tcheck helpers in C
selftests/powerpc: Allow tests to extend their kill timeout
selftests/powerpc: Introduce GPR asm helper header file
selftests/powerpc: Move VMX stack frame macros to header file
selftests/powerpc: Rework FPU stack placement macros and move to header file
selftests/powerpc: Check for VSX preservation across userspace preemption
...
This patch updates Jack type bitmask to include SND_JACK_LINEOUT while
creating a new jack, so that LINEOUT events are reported properly.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPIB is read currently from a buffer position in memory (indicated by
the registers DPIB[U|L]BASE).Driver reads the position buffer on BDL
completion interrupts to report the DMA position. But the BDL completion
interrupt only indicates the last DMA transfer of the buffer is
completed at the Intel HD Audio subsystem boundary. The periodic DMA
Position-in-Buffer writes may be scheduled at the same time or later
than the MSI and does not guarantee to reflect the position of the last
buffer that was transferred.
Whereas DPIB register in HDA space(vendor specific register indicated by
SDxDPIB) reflects the actual data that is transferred. Hence update the
position based on DPIB for playback.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently on some headsets slight pops can be heard during DAPM
power-up/down. This can also be witnessed during the HP detect
procedure. This patch addresses the issue by adjusting DAPM power
sequencing slightly, the introduction of delays and use of
minimum HP gain to avoid such noise artefacts.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The set_bias_level toggles the PDN signal when entering
SND_SOC_BIAS_STANDBY and SND_SOC_BIAS_OFF. However this has no effect and
actually breaks things down (tested with TAS5717) due to the following
reasons:
1) holding down PDN does not save power but holding down RST does
2) now hard mute via register 0x5 is implemented and therefore it is no
longer needed to toggle PDN to enter all channel shut down
3) in order to leave PDN it is required to toggle the RST signal (see
TAS5721 datasheet), which was not implemented
4) toggling PDN as implemented actually mutes PWMs and there is no audio
output (tested on TAS5717)
For these reasons remove the PDN signal toggling and just initialize it to
inactive in probe().
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
TAS5721 datasheet recommends to wait at least 13.5ms after deasserting the
RESET signal. For TAS5717 this time is only 12ms, which was the original
value in the code.
Extend the wait time after deasserting RESET from 12 to 13.5ms to comply
with the TAS5721 specification.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel 1 and 2 Mixer Volume controls (registers 0x72/0x73 and 0x76/0x77)
were wrongly assigned to tas5711_controls in commit f252d2346022
("ASoC: tas571x: add input channel mixer for TAS5717/19")
Therefore move them to tas5717_controls.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Wait extra 50ms after writing the oscillator trim register in probe(), as
recommended by the TAS5721 and TAS5711 datasheets.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJX7pEPExxicm9vbmllQGtlcm5lbC5vcmcACgkQJNaLcl1Uh9Du
Fgf+MAOLDX8z7TbxAM4TnpPO7pRYF+wR+AWamVoUnHrq+gdsUkcKbnTlE8PP05Sp
VDf/ugCMcAQoYrrXPPiZLLB6YsJf2eXjlrTeF5eG/oHRC0mBeM/U6nHblNltFPKl
clV5jTm8Rq/I0AHAiYeTDetQsypK3eVjJ0PZLdenVWF+kL/+aTJ4GXIGgH27aSQC
7lwQZBRWfvGyE/IRu2NNXTPMNSaos/JtLh2/Y2qkWVEQ8YYwFxgRkfCRDHbFk2fK
8/mdWWlaBrApZN8t/RlJxo6rxuQGUn01HFvLpRK1N0EMuLWaTUFHQZtUV/KF/JSz
6Gj4tPLvDke0f4N2tIwoF9quXA==
=qgCG
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.9
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
The recent series of changes to the caching in the SSI driver have
caused a number of problems to appear in some test systems. These are
still not fully understood but we're coming up to the merge window so
for now let's revert commit 7de2763d9b (ASoC: fsl_ssi: Remove
.num_reg_defaults_raw from regmap_config) as backing that out seems to
resolve the problem on affected systems.
Reported-by: Maciej S. Szmigiero" <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Currently there is a memory leak of module on a ENOMEM return path.
Fix this by kfree'ing module before returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds SNDRV_PCM_TRIGGER_SUSPEND/RESUME.
Otherwise, it breaks rsnd driver internal start/stop counter
when suspend/resume. This issue was reported/tested by Hiep
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports a below warning.
sound/soc/codecs/da7219.c:804:57: warning: dubious: x & !y
The line includes a condition statement; '(a < b) & !c'. Practically, the
evaluated value of this statement equals to the value of '(a < b) && !c'.
Although, it's not an usual way to use bitwise operations as logical
operations to several conditions.
This commit fixes the bug.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This hardware supports only 2-channel DAI, even mono ADC digital output
has two channels with the same data.
Having min_channels=1 results in broken playback of mono files in setups
where CPU DAI supports mono.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As long as reading datasheet of STAC9766/9767, this driver includes wrong
usage of DECLARE_TLV_DB_LINEAR().
In "8.1.2. Master Volume Registers", attenuation of lineout volumes is
represented in 5 bits by -1.5 dB/step from 0 to -46.5 dB. Thus,
'master_tlv' should be dB step representation.
In "8.1.14. Record Gain", gain of volumes is represented in 4 bits by
1.5 dB/step from 0 to 22.5 dB. Thus, 'record_tlv' should be dB step
representation.
In "8.1.5. PC BEEP Volume", attenuation of volume is represented in 4 bits
by -3 dB/step from 0 to 45 dB. Thus, 'beep_tlv' should be dB step
representation.
In "8.1.7. Stereo or Mic Volume" and so on, gain of volumes is represented
in 5 bits by -1.5 dB from 12 to -34.5 dB. Thus, 'mix_tlv' should be dB
step representation.
Totally, current implementation includes misuse of TLV-related macro.
This commit replaces usage of DECLARE_TLV_DB_LINEAR() with
SNDRV_CTL_TLVD_DECLARE_DB_SCALE(), to give proper information to
applications in user land.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver has some unused variables. They should be removed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As long as reading datasheet of WM8991, this driver includes wrong usage
of DECLARE_TLV_DB_LINEAR().
In "Table 6 Input PGA Volume Range", volume is represented in 5 bits by
1.5 dB/step between -16.5/30.0 dB. Thus, 'in_pga_tlv' should be dB step
representation.
In "Table 34 LOMIX and ROMIX Volume Range", volume is represented in three
bits by -3 dB/step from 0 to -21 dB. Thus, 'out_mix_tlv' should be dB step
represenation.
In "Table 36 LOPGA, ROPGA, LOUT, ROUT and SPKVOL Volume Range", volume is
represented in 7 bits by 1 dB/step from -73 to 6 dB, including mute. Thus,
'out_pga_tlv' should be dB step representation.
In "Table 26 Digital Volume Range", volume is represented in 8 bits by
3/8 dB/step from -71.625 to 0 dB. Thus, 'out_dac_tlv' should be dB step
representation.
In "Table 16 ADC Digital Volume Range", volume is represented in 8 bits by
3/8 dB/step from -71.625 to 17.625 dB. Thus, 'in_adc_tlv' should be dB step
representation.
In "Table 23 Digital Sidetone Volume", volume is represented in 5 bits by
3 dB/step from -36 to 0 dB. Thus, 'out_sidetone_tlv' should be dB step
representation.
In "Table 12 Left Input Mixer Volume Control", volume is represented in
3 bits by 3 dB/step from -12 to 6 dB
Totally, current implementation includes misuse of TLV-related macro.
This commit replaces usage of DECLARE_TLV_DB_LINEAR() with proper macros,
to give proper information to applications in user land.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports a below warning.
tpa6130a2.c:193:33: warning: symbol 'tpa6130a2_component_driver' was not declared. Should it be static?
The symbol is just used inner the file. Forthermore, it's constant. Thus,
it's better to add static and const qualifier.
This commit adds it.
Fixes: cb7e62256e (ASoC: tpa6130a2: Register component)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports below warnings.
rt5616.c:1270:24: warning: symbol 'rt5616_aif_dai_ops' was not declared. Should it be static?
rt5616.c:1277:27: warning: symbol 'rt5616_dai' was not declared. Should it be static?
These two symbols are just used inner the file, thus it's better to add
static qualifier.
This commit adds it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
The later Arizona parts do run write sequences to power up and down the
speaker path as such a delay needs to be inserted into the DAPM sequence
to allow this to run. This patch adds appropriate delays into the
existing coalesced delay scheme.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When debugging it is useful to check the total power up/down delay that
is executed as part of the coalesced output delay. This patch adds some
debug prints for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HP Spectre x360 with CX20724 codec has two speaker outputs while the
BIOS sets up only the bottom one (NID 0x17) and disables the top one
(NID 0x1d).
This patch adds a fixup simply defining the proper pincfg for NID 0x1d
so that the top speaker works as is.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=169071
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add channel and rate constraints for Refcap and dmiccap devices
respectively.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When operating the BE, we should print out the dai_link name of BE other
than FE. This is useful when analyzing the kernel log.
Signed-off-by: Donglin Peng <pengdonglin@smartisan.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
tlv320dac31xx is a subset of tlv320aic31xx:
- it does not have MIC inputs and ADC, thus capture is not supported,
- it has analog inputs AIN1/AIN2 that can be mixed into output.
Although tlv320dac31xx does work with tlv320aic31xx driver, this setup
does register non-existent widgets and non-existent capture stream.
Thus userspace lists non-existent objects in user interfaces, an can
access these, causing operations with device registers that are
declared as "reserved" in tlv320dac31xx datasheet.
This patch fixes this situation by separating controls/widgets/routes
into common, aic31xx-specific, and dac31xx-specific parts. Only parts
that match actual hardware (as declared in "compatible" device tree
property) are registered.
Changes from v1:
- update device tree binding documentation,
- rebased on top of "ASoC: codec duplicated callback function goes to
component on tlv320aic31xx" commit.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently if AAD is enabled in the device, during system suspend
the feature remains, regardless of whether the codec is a wake-up
source or not. This means some additional power is being used
which is unnecessary, and can causes issues with some platforms'
IRQ handlers where state changes during system suspend aren't
captured.
This patch updates the driver to disable AAD during suspend, if
we're not a wake-up source, and then re-enables this on resume.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the reset code in i2c_probe only resets the AAD part of
the device and not the entire codec. This patch updates the driver
to resolve this and ensures that if the codec is still active from
a previous boot then the audio paths are powered down prior to
reset.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver exposes range of sample rates between 8KHz to
192KHz as a part of dai_driver. This does not hold true as the limited
number sample rates are allowed in hw_params DAI callback. This patch
limits the sample rates exposed via dai_driver.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename "sun4i_codec_widgets" to "sun4i_codec_controls" for
consistency with the struct field name.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Code undo operations in power enable errror path explicitly, instead of
reusing power disable path and playing with return values there.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree property to define auxiliary devices to be added to
simle-audio-card.
Together with proper audio routing definition, this allows to use
simple-card in setups where separate amplifier chip is connected to
codec's output.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The booting process for the DSP is clearly separated into two parts, the
preloader brings up the core and downloads code, then the main widget
starts the code actually executing. However the shutdown sequence is all
handled with the main widget.
To allow the preloading to be run independently of the main audio bring
up it makes sense, and is generally just cleaner, for the preloader
widget to shutdown those things it initialised. This patch moves the
appropriate parts of the shutdown process into the preloader widget.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Between when we load the DSP and when it actually starts running put the
core into a lower power state where the memory is retained but nothing
is clocked.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the 1ms msleep in wm_adsp2_ena with a usleep_range, as per
normal guidance on delay functions. Also tighten up the delay a little
as 1ms was quite generous.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio component framework code has not yet landed in the i915 driver
so drop the use of the API for the time being.
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Jeeja KP <jeeja.kp@intel.com>
We have two new Dell laptop models, they have the same ALC255 pin
definition, but not in the pin quirk table yet, as a result, the
headset microphone can't work. After adding the definition in the
table, the headset microphone works well.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, usb-line6 module exports an array of MIDI manufacturer ID and
usb-pod module uses it. However, the declaration is not the definition in
common header. The difference is explicit length of array. Although
compiler calculates it and everything goes well, it's better to use the
same representation between definition and declaration.
This commit fills the length of array for usb-line6 module. As a small
good sub-effect, this commit suppress below warnings from static analysis
by sparse v0.5.0.
sound/usb/line6/driver.c:274:43: error: cannot size expression
sound/usb/line6/driver.c:275:16: error: cannot size expression
sound/usb/line6/driver.c:276:16: error: cannot size expression
sound/usb/line6/driver.c:277:16: error: cannot size expression
Fixes: 705ececd1c ("Staging: add line6 usb driver")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is used by the Chromebook Pixel 2015.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
[john@metanate.com:
- forward-port driver from Chromium OS 3.14 tree to master
- remove wake on voice function that isn't supported by upstream rt5677
driver
- remote owner assignment in platform_driver (Evan McClain)
- convert to devm_snd_soc_register_card (Evan McClain)
- add a full copyright header based on module license and Chromium OS
Git history
]
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Genki Marshall <genki@genki.is>
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Chromebook Pixel 2015 uses this codec with the ACPI ID RT5677CE, but
does not use the standard DT property names so add a new function to
parse the codec properties from these ACPI properties.
Also, the GPIOs are only available by index, so we need to register a
mapping to allow machine drivers to access the GPIOs by name.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The second declaration of status is shadowing the status of a higher
scope. This uninitialized status results in garbage being returned
by the !x86_match_cpu(cpu_ids) || !iosf_mbi_available() return exit
path. Fix this by removing the extraneous second declaration of
status.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With codec read sometimes the pin_sense shows invalid monitor present
and eld_valid. Currently driver polls for few times to get the valid
ELD data.
To avoid the latency, Instead of reading ELD from codec, read it
directly from the display driver using audio component framework.
Removed the direct codec helper functions.
Signed-off-by: Sandeep Tayal <sandeepx.tayal@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trival fix, some dev_err/deb_dbg messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trival fix, some pr_err messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trival fix, some dev_err and deb_dbg messages are missing a \n, so
add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trival fix, some dev_* messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is simple sound card time, we could assign different codec
to a interface without making a specific driver for it. The SPDIF
and I2S interface for Samsung would be possible used by
simple-sound-card, but not sure about the PCM.
Those S3C time entries are left alone as I don't think any new board
would need them.
Signed-off-by: Randy Li <ayaka@soulik.info>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the DSP loading is split into two widgets, the preloader that
is a snd_soc_dapm_dai_link widget which starts a thread to download
the firmware, and the DSP itself which is a snd_soc_dapm_out_drv and
synchronises the thread back in to the DAPM sequence. This allows the
firmware download to be overlapped with the rest of the path bring up.
The use of a snd_soc_dapm_dai_link widget requires the preloader to be part
of the audio path in DAPM, really a supply widget is a better fit for the
preloader. The preloader is something that needs to be done for the DSP to
function, not a part of the audio path itself.
This change makes the DSP preloader widget a supply widget, which as well
as probably being a better fit will also make it much simpler to power up
the preloader widget to trigger firmware download to the core independently
of the audio path coming up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently SYSCLK is attached to every compressed DAI as this follows the
pattern of attaching clocks to the chips inputs and outputs, however, it is
really the DSP that requires the clock here. As firmware download can be a
significant part of the path startup time for these devices occasionally it
would be desirable to download the firmware in advance of the path being
brought up.
To help facilitate this early firmware loading this patch attaches the
SYSCLK to the DSP preloader widget. This also saves us adding a new route
to SYSCLK every time a new compressed DAI is created.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of the work to download firmware before the audio path is brought
up the DSP will be put into a low power state between downloading firmware
to the core and starting it running. This will mean that the firmware ALSA
controls are not accessible in the hardware during this period of time.
To prepare for this change we gate access to the hardware in the ALSA
control handlers on the DSP being running rather than simply booted and
move the synchronisation of the control caches out of the preloader delayed
work and into the main DAPM thread after the DSP will have been brought out
of its low power state.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the wm_adsp driver has a flag that indicates the DSP is
"running", this flag is used to gate access to the hardware. However this
flag is actually set in the firmware download thread after the firmware has
been downloaded, but this is before the core is actually started running,
so really it currently indicates that the core has been booted and is
perhaps running.
This patch clearly separates out the concepts of booted (firmware is
downloaded) and running (code is executing on the DSP) within the wm_adsp
driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After moving tpa6130a2 power management to DAPM, if chip can be physically
powered off (either reset_gpio is defined, or regulator indeed removes
power), then volume change no longer works unless chip is on due to
a running stream.
Fix that by entering regcache cache_only mode while chip is off.
Move regcache calls to tpa6130a2_power() to get them at driver init time
as well.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since modules ids are generated dynamically, we do not know the id
associate with modules in another pipelines. This limits our ability to
tell DSP about neighbouring modules.
So add a table for quick referencing of allocated module ids.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Post bind parameters of KPB module contains the instance id's of
neighbouring modules in the sink path
Now that module instance ids are generated dynamically we need to update
these parameters as well, so use the table created and update the ids
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use private id's of module instances that are generated during
init_module for the IPC messages to DSP. These id's are freed
up during delete pipeline.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver needs to send unique module instance id to firmware while
creating the module and uses this id to communicate with DSP for setting
parameters while audio use case is ongoing.
But, we have upper bound of instance ID. The current IDs are coming from
topology but it doesn't know the upper bound and can't assign unique
id's subject to upper bounds as we can create a big graph but not all
parts running at same time.
This patch adds a 128bit unique id management routines which are built
on top of ffz() for faster implementation. Unfortunately ffz() works on
32bits values, so additional code is added on top of ffz() to create a
128bit unique id.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A20 has a few extra registers that the A10 doesn't have.
Therefore, use different regmaps for A10 as compared to A20.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the registers defined in the driver are only usable on the
A20. Rename these registers.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pop happens when mclk applied but dmic's own boot-time
Specify dmic delay times in dt to make sure
clocks are ready earlier than dmic working
Signed-off-by: Wonjoon Lee <woojoo.lee@samsung.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DragonFly quirk added in 42e3121d90 ("ALSA: usb-audio: Add a more
accurate volume quirk for AudioQuest DragonFly") applies a custom dB map
on the volume control when its range is reported as 0..50 (0 .. 0.2dB).
However, there exists at least one other variant (hw v1.0c, as opposed
to the tested v1.2) which reports a different non-sensical volume range
(0..53) and the custom map is therefore not applied for that device.
This results in all of the volume change appearing close to 100% on
mixer UIs that utilize the dB TLV information.
Add a fallback case where no dB TLV is reported at all if the control
range is not 0..50 but still 0..N where N <= 1000 (3.9 dB). Also
restrict the quirk to only apply to the volume control as there is also
a mute control which would match the check otherwise.
Fixes: 42e3121d90 ("ALSA: usb-audio: Add a more accurate volume quirk for AudioQuest DragonFly")
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Reported-by: David W <regulars@d-dub.org.uk>
Tested-by: David W <regulars@d-dub.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DP MST provides the capability to send multiple video and audio streams
through a single port. This requires the API's between i915 and audio
drivers to distinguish between multiple audio capable displays that can be
connected to a port. Currently only the port identity is shared in the
APIs. This patch adds support for MST with an additional parameter
'int pipe'. The existing parameter 'port' does not change it's meaning.
pipe =
MST : display pipe that the stream originates from
Non-MST : -1
Affected APIs:
struct i915_audio_component_ops
- int (*sync_audio_rate)(struct device *, int port, int rate);
+ int (*sync_audio_rate)(struct device *, int port, int pipe,
+ int rate);
- int (*get_eld)(struct device *, int port, bool *enabled,
- unsigned char *buf, int max_bytes);
+ int (*get_eld)(struct device *, int port, int pipe,
+ bool *enabled, unsigned char *buf, int max_bytes);
struct i915_audio_component_audio_ops
- void (*pin_eld_notify)(void *audio_ptr, int port);
+ void (*pin_eld_notify)(void *audio_ptr, int port, int pipe);
This patch makes dummy changes in the audio drivers (thanks Libin) for
build to succeed. The audio side drivers will send the right 'pipe' values
for MST in patches that will follow.
v2:
Renamed the new API parameter from 'dev_id' to 'pipe'. (Jim, Ville)
Included Asoc driver API compatibility changes from Jeeja.
Added WARN_ON() for invalid pipe in get_saved_encoder(). (Takashi)
Added comment for av_enc_map[] definition. (Takashi)
v3:
Fixed logic error introduced while renaming 'dev_id' as 'pipe' (Ville)
Renamed get_saved_encoder() to get_saved_enc() to reduce line length
v4:
Rebased.
Parameter check for pipe < -1 values in get_saved_enc() (Ville)
Switched to for_each_pipe() in get_saved_enc() (Ville)
Renamed 'pipe' to 'dev_id' in audio side code (Takashi)
v5:
Included a comment for the dev_id arg. (Libin)
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474488168-2343-1-git-send-email-dhinakaran.pandiyan@intel.com
A cleanup removed a couple of members from struct snd_soc_codec_driver
after changing codec drivers to no longer use them, but one codec
was missed in the process, giving a build error:
sound/soc/codecs/cq93vc.c:134:2: error: unknown field 'controls' specified in initializer
.controls = cq93vc_snd_controls,
This moves the members from the cq93vc codec driver to its component driver
just like the other codecs already had.
Fixes: 8073aefa60 ("ASoC: remove codec duplicated callback function")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer callbacks of ali5451 driver may return the value at the
boundary occasionally, and it results in the kernel warning like
snd_ali5451 0000:00:06.0: BUG: , pos = 16384, buffer size = 16384, period size = 1024
It seems that folding the position offset is enough for fixing the
warning and no ill-effect has been seen by that.
Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Srinivas Kandagatla