We may not free tl_hash when IO is suspended, since we can not wait
until ap_bio_cnt reaches zero.
We can do this after susp reched 0, since then tl_clear was called
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
After disconnect (most likely mdev->net_cnt == 0) and we are
still in an unstable state (!drbd_state_is_stable()). When we
get an IO request in drbd_get_max_buffers() (called from
__inc_ap_bio_cond(), called from inc_ap_bio()) we wake up
misc_wait. Misc_wait is also used in inc_ap_bio() to sleep
until the outcome of __inc_ap_bio_cond() changes. => Busy loop!
Solution: Have a dedicated wait queue for get_net_conf() and
put_net_conf().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Make sure the state engine can deny two primaries to connect
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since we can not thaw the transfer log, the next logical step is
to allow reconnects while the fence-peer handler runs.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If IO was frozen for a temporal network outage, resend the
content of the transfer-log into the newly established connection.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With that the drbd_fail_pending_reads() function becomes obsolete.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
It was a now abandoned attempt to throttle resync bandwidth
based on the delay it causes on the bulk data socket.
It has no userbase yet, and has been disabled by
9173465ccb51c09cc3102a10af93e9f469a0af6f already.
This removes the now unused code.
The basic feature, namely using up "idle" bandwith
of network and disk IO subsystem, with minimal impact
to application IO, is being reimplemented differently.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver. There were two flags in the bio that were
missing in the requests: BIO_RW_UNPLUG and BIO_RW_AHEAD. Also I've
renamed two request flags that had a superflous RW in them.
Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
drbd/drbd_receiver.c: linux/mm.h is included more than once.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
quoting tcp(7):
On individual connections, the socket buffer size must be set prior to the
listen(2) or connect(2) calls in order to have it take effect.
This adds a wrapper to do so, and uses it appropriately.
Improves performance in certain situations.
Note that because we cannot easily determine which socket will be
"meta" and wich "data" (bulk) socket, we adjust both sockets.
Previously, DRBD only adjusted the bufsizes of the "data" socket.
Thanks again to Eduard.Guzovsky@stratus.com.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The late-UUID writing is delayed until the next release.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The choice was to either delay creation of the new UUID until
IO got thawed or to delay it until the first IO request.
Both are correct, the later is more friendly to users of
dual-primary setups, that actually only write on one side.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now that the peer may handle multi-bio EEs,
we can ignore the peer's limit,
and concentrate on the limits of the local IO stack.
This is safe accross drbd protocol versions,
as our queue_max_sectors() will be adjusted accordingly.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This should allow for better performance if the lower level IO stack
of the peers differs in limits exposed either via the queue,
or via some merge_bvec_fn.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Delay_probes are new packets in the DRBD protocol, which allow
DRBD to know the current delay packets have on the data socket.
(relative to the meta data socket)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Some wish to be notified of all instances of split brain, not just those that
go unresolved. The initial-split-brain handler is called to notify someone
upon detection of all split brain conditions even if auto-recovery policies
are configured.
Signed-off-by: Adam Gandelman <adam.gandelman@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Even if it should never happen if the peer does behave, we need to
double check, and not even attempt access beyond end of device.
It usually would be caught by lower layers, resulting in "IO error",
but may also end up in the internal meta data area.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Don't forget to drain the digest in case we cannot satisfy a
checksum based resync or online-verify request.
It would additionally cause a protocoll error,
dropping the connection.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
block_id may be ID_SYNCER,
as well as checksum based resync request magic, or online verify magic.
Let's just drop that ASSERT.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The patch just convert all blkdev_issue_xxx function to common
set of flags. Wait/allocation semantics preserved.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fixes a race and potential kernel panic if e.g. the worker was just
about to send a few P_RS_IS_IN_SYNC via the meta socket for checksum
based resync, while the receiver destroys the sockets in
drbd_disconnect.
To make sure no-one is using the meta socket,
it is not enough to stop the asender...
Grab the meta socket mutex before destroying it.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Situation:
we have diverging data sets, i.e. we had a split brain somewhen,
but currently are connected, one node diskless.
Then we try to attach that disk, figure it is consistent,
but has a diverging data set, we refuse to attach.
This led to strange state changes:
22:18:35 bb drbd1: peer( Unknown -> Primary ) conn( WFReportParams -> Connected) pdsk( DUnknown -> UpToDate )
22:19:30 bb drbd1: disk( Diskless -> Attaching )
22:19:30 bb drbd1: disk( Attaching -> Negotiating )
22:19:30 bb drbd1: drbd_sync_handshake:
22:19:30 bb drbd1: self 97BF25798B9D5222:F33D1F62ADE698DD:4269796F9D027C83:AC45D8B5C3C1BF93 bits:19449 flags:0
22:19:30 bb drbd1: peer 280DFB6E125465D3:F33D1F62ADE698DC:4269796F9D027C82:AC45D8B5C3C1BF93 bits:2575806 flags:0
22:19:30 bb drbd1: uuid_compare()=100 by rule 90
22:19:30 bb drbd1: Split-Brain detected, dropping connection!
22:19:30 bb drbd1: disk( Negotiating -> Diskless )
while the other side says:
22:19:30 aa drbd1: Split-Brain detected, dropping connection!
22:19:30 aa drbd1: Disk attach process on the peer node was aborted.
22:19:30 aa drbd1: conn( Connected -> TOO_LARGE ) pdsk( Diskless -> Consistent )
This should be fixed now.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Test the just-allocated value for NULL rather than some other value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y;
statement S;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
(
if ((x) == NULL) S
|
if (
- y
+ x
== NULL)
S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Immediately after changing the write ordering method, the epoch can already
be finished at this point.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since 8.3.3 we fail to do the resync when a partial resynch is not
possible, but a full synch is necessary.
This regression was introduced with 7101539930c0a89146959e7a39c09ad9c3516434
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Otherwise the 'state fixup' in the receiver will change to Unconnected,
but the receiver will terminate itself, and any attempt at 'down'ing
that drbd later will block forever.
see also Bugz. #259
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When there are many blocks on the fly (ua), and the AL gets into "starving"
mode (random IO, scattered all over the device), and the connections gets
interrupted, the receiver thread deadlocks in the drbd_disconnect() code path.
Affected are only nodes in Primary role.
The bug triggers most likely on system that mirror over "long distances"
Regression introduced shortly before 8.3.3
with git commit 31e0f1250f174ac1ee317f360943a0159e19edc8
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It is force-included on the gcc command line since at least 2.6.15.
Explicit include lines seem to break compilation now in certain configurations.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Philipp Reisner