- Intc imporvements [Yuriy]
- VDK platform updates [Alexey]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WPBu
-----END PGP SIGNATURE-----
Merge tag 'arc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- Intc imporvements [Yuriy]
- VDK platform updates [Alexey]
* tag 'arc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-*] ARC_HAS_COH_CACHES no longer relevant
ARCv2: intc: Delete useless comments in Device Trees
ARCv2: IDU-intc: Delete deprecated parameters in Device Trees
ARCv2: IDU-intc: mask all common interrupts by default
ARCv2: IDU-intc: Use build registers for getting numbers of interrupts
ARCv2: intc: Set default priority for all core interrupts
ARCv2: intc: Use runtime value of irq count for setting up intc
ARCv2: intc: Rework the build time irq count information
ARC: [intc-*]: confine NR_CPU_IRQS to intc code
ARCv2: intc: Use ARC_REG_STATUS32 for addressing STATUS32 reg
arc: vdk: Add support of UIO
arc: vdk: Add support of MMC controller
arc: vdk: Disable halt on reset
No need for specifying a list of interrupts in the declaration
of IDU interrupt controller anymore since the kernel can obtain
a number of supported interrupts from the build register.
Also delete support of the second parameter for devices which
are connected to IDU because it is not used anywhere.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This enhancement is needed to allow masking all available common interrupts
in IDU interrupt controller in boot time since the kernel can
discover a number of them from the build register. Also now there
is no need to specify in device tree a list of used core interrupts
by IDU. E.g. before:
idu_intc: idu-interrupt-controller {
compatible = "snps,archs-idu-intc";
interrupt-controller;
interrupt-parent = <&core_intc>;
#interrupt-cells = <2>;
interrupts = <24 25 26 27 28 29 30 31>;
};
and after:
idu_intc: idu-interrupt-controller {
compatible = "snps,archs-idu-intc";
interrupt-controller;
interrupt-parent = <&core_intc>;
#interrupt-cells = <2>;
};
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
After reset all interrupts in the core interrupt controller has
the highest priority P0. If the platform supports Fast IRQs and
has more than 1 banks of registers then CPU automatically switch
banks of registers when P0 interrupt comes.
The problem is that the kernel expects that by default switching
of banks is not used by all interrupts. It is necessary to set a
default nonzero priority for all available interrupts to avoid
undefined behaviour.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Currently Kconfig knob ARC_NUMBER_OF_INTERRUPTS is used as indicator of
hard irq count. But it is flawed that it doesn't affect
- NR_IRQS : for number of virtual interrupts
- NR_CPU_IRQS : for number of hardware interrupts
Moreover the actual hardware irq count might still not be same as
ARC_NUMBER_OF_INTERRUPTS. So use the information availble in the
Build Configuration Registers and get rid of the Kconfig option.
We still need "some" build time info about irq count to set up
sufficient number of vector table entries. This is done with a
sufficiently large NR_CPU_IRQS which will eventually be used soley for
that purpose (subsequent patches will remove its usage elsewhere)
So to summarize what this patch does:
* NR_CPU_IRQS defines a maximum number of hardware interrupts.
* Remove ARC_NUMBER_OF_INTERRUPTS option and create interrupts
table for all possible hardware interrupts.
* Increase a maximum number of virtual IRQs to 512. ARCv2 can
support 240 interrupts in the core interrupts controllers
and 128 interrupts in IDU. Thus 512 virtual IRQs must be
enough for most configurations of boards.
This patch leads to NR_CPU_IRQS in 2 places, to reduce the overall
churn. The next patch will remove the 2nd definition anyways.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: reworked the changelog a bit]
It is better to use it instead of magic numbers.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
After emulating an unaligned access in delay slot of a branch, we
pretend as the delay slot never happened - so return back to actual
branch target (or next PC if branch was not taken).
Curently we did this by handling STATUS32.DE, we also need to clear the
BTA.T bit, which is disregarded when returning from original misaligned
exception, but could cause weirdness if it took the interrupt return
path (in case interrupt was acive too)
One ARC700 customer ran into this when enabling unaligned access fixup
for kernel mode accesses as well
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This is needed on HS38 cores, for setting up IO-Coherency aperture properly
The polling could perturb the caches and coherecy fabric which could be
wrong in the small window when Master is setting up IOC aperture etc
in arc_cache_init()
We do it only for ARCv2 based builds to not affect EZChip ARCompact
based platform.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For run-on-reset SMP configs, non master cores call a routine which
waits until Master gives it a "go" signal (currently using a shared
mem flag). The same routine then jumps off the well known entry point of
all non Master cores i.e. @first_lines_of_secondary
This patch moves out the last part into one single place in early boot
code.
This is better in terms of absraction (the wait API only waits) and
returns, leaving out the "jump off to" part.
In actual implementation this requires some restructuring of the early
boot code as well as Master now jumps to BSS setup explicitly,
vs. falling thru into it before.
Technically this patch doesn't cause any functional change, it just
moves the ugly #ifdef'ry from assembly code to "C"
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Ignore value of interrupt distribution mode for common interrupts in
IDU since setting of affinity using value from Device Tree is deprecated
in ARC. Originally it is done in idu_irq_xlate() function and it is
semantically wrong and does not guaranty that an affinity value will be
set properly. idu_irq_enable() function is better place for
initialization of common interrupts.
By default send all common interrupts to all available online CPUs.
The affinity of common interrupts in IDU must be set manually since
in some cases the kernel will not call irq_set_affinity() by itself:
1. When the kernel is not configured with support of SMP.
2. When the kernel is configured with support of SMP but upper
interrupt controllers does not support setting of the affinity
and cannot propagate it to IDU.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
commit d65283f7b6 added mod->arch.secstr under
CONFIG_ARC_DW2_UNWIND, but used it unconditionally which broke builds
when the option was disabled. Fix that by adjusting the #ifdef guard.
And while at it add a missing guard (for unwinder) in module.c as well
Reported-by: Waldemar Brodkorb <wbx@openadk.org>
Cc: stable@vger.kernel.org #4.9
Fixes: d65283f7b6 ("ARC: module: elide loop to save reference to .eh_frame")
Tested-by: Anton Kolesov <akolesov@synopsys.com>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
[abrodkin: provided fixlet to Kconfig per failure in allnoconfig build]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
It is necessary to call entry/exit functions for parent interrupt
controllers for proper masking/unmasking of interrupt lines.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
It is necessary to use hwirq instead of virq when you communicate
with an interrupt controller since there is no guaranty that virq
numbers match hwirq numbers.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC HS Cores support configurable multiple interrupt priorities of upto
16 levels. In commit dec2b2849c ("ARCv2: intc: Allow interruption by
lowest priority interrupt") we switched to 15 which seems a bit
excessive given that there would be rare hardware implementing so many
preemption levels AND running Linux. It would seem that 2 levels will be
more common so switch to 1 as the default priority level. This will be
the "lower" priority level saving 0 for implementing NMI style support.
This scheme also works in systems with more than 2 prioity levels as
well.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
And while at it - use the proper assembler macro which includes the
optional irq tracing already - de-uglify'ing the code a bit
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This adds support for
- CONFIG_ARC_TIMERS : legacy 32-bit TIMER0 and TIMER1 which count UP
from @CNT to @LIMIT, before optionally triggering an interrupt.
These are programmed using ARC auxiliary register interface.
These are present in all ARC cores (ARC700 and ARC HS38)
TIMER0 serves as clockevent for all ARC linux builds.
TIMER1 is used for clocksource in arc700 builds.
- CONFIG_ARC_TIMERS_64BIT: 64-bit counters, RTC and GFRC found in
ARC HS38 cores. These are independnet IP blocks with different
programming model respectively.
Link: http://lkml.kernel.org/r/20161111231132.GA4186@mai
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Also remove the dependency on ARCv2, to increase compile coverage for
!ARCV2 builds
Acked-by: Daniel Lezcano <daniel.lezcnao@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
to allow future git mv of the driver into drivers/clocksource
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original distinction was done as they were developed at different
times and primarily because they are specific to UP (RTC) and SMP (GFRC).
But given that driver handles that at runtime, (i.e. not allowing
RTC as clocksource in SMP), we can simplify things a bit.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
... don't rely on cpuinfo populated in arc boot code. This paves way for
moving this code in drivers/clocksource/
And while at it, convert the WARN() to pr_warn() as sugested by Daniel
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
A standard "C" shift will be handled appropriately by the compiler
depending on the endian for the build. So we don't need the
explicit distinction in code
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC linux uses 2 distribution modes for common interrupts: round robin
mode (IDU_M_DISTRI_RR) and a simple destination mode (IDU_M_DISTRI_DEST).
The first one is used when more than 1 cores may handle a common interrupt
and the second one is used when only 1 core may handle a common interrupt.
However idu_irq_set_affinity() always sets IDU_M_DISTRI_RR for all affinity
values. But there is no sense in setting of such mode if only 1 core must
handle a common interrupt.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This came up when reviewing code to address missing IRQ affinity
setting in AXS103 platform and/or implementing hierarchical IRQ domains
- smp_ipi_irq_setup() callers pass hwirq but in turn calls
request_percpu_irq() which expects a linux virq. So invoke
irq_find_mapping() to do the conversion
(also explicitify this in code by renaming the args appropriately)
- idu_of_init()/idu_cascade_isr() were similarly using linux virq where
hwirq is expected, so do the conversion using irqd_to_hwirq() helper
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
[vgupta: made changelog a bit concise a bit]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For CONFIG_SERIAL_EARLYCON we need 800MHz for NPS SoC
The early console driver uses BASE_BAUD and not using dtb.
The default of 50MHz is NOT good for NPS SoC.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The current code doesn't even compile as somehow the inline assembly
can't see the register names defined as ARC_RTC_*
I'm pretty sure It worked when I first got it merged, but the tools were
definitely different then.
So better to write this in "C" anyways.
CC: stable@vger.kernel.org #4.2+
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original syscall only used to return errno to indicate if cmpxchg
succeeded. It was not returning the "previous" value which typical cmpxchg
callers are interested in to build their slowpaths or retry loops.
Given user preemption in syscall return path etc, it is not wise to
check this in userspace afterwards, but should be what kernel actually
observed in the syscall.
So change the syscall interface to always return the previous value and
additionally set Z flag to indicate whether operation succeeded or not
(just like ARM implementation when they used to have this syscall)
The flag approach avoids having to put_user errno which is nice given
the use case for this syscall cares mostly about the "previous" value.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
At smp_prepare_cpus() we set present cpu mask as part of init
for all CPUs at range [0-max_cpus].
This is done without checking if this mask is already being set.
At platform of eznps this mask is already being initialized at
smp_init_cpus() by using hook plat_smp_ops.init_early_smp().
So to avoid overriding of present cpu mask we check the number of
bits which are set in this mask. At the begin only bit for boot CPU
is set so if number of bits already set is no more than one we can be
assure that there is no overriding of this mask.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now that we have referece to section name string table in
apply_relocate_add(), use it to
- print the name of section being relocated
- print symbol with NULL name (since it refers to a section)
before
| Section to fixup 7000a060
| =========================================================
| rela->r_off | rela->addend | sym->st_value | ADDR | VALUE
| =========================================================
| 1c 0 7000e000 7000a07c 7000e000 []
| 40 0 7000a000 7000a0a0 7000a000 []
after
| Section to fixup .eh_frame @7000a060
| =========================================================
| r_off r_add st_value ADDRESS VALUE
| =========================================================
| 1c 0 7000e000 7000a07c 7000e000 [.init.text]
| 40 0 7000a000 7000a0a0 7000a000 [.exit.text]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The loop was really needed in .debug_frame regime where wanted make it
as SH_ALLOC so that apply_relocate_add() would process it. That's not
needed for .eh_frame, so we check this in apply_relocate_add() which
gets called for each section.
Note that we need to save reference to "section name strings" section in
module_frob_arch_sections() since apply_relocate_add() doesn't get that
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The motivation is to identify ARC750 vs. ARC770 (we currently print
generic "ARC700").
A given ARC700 release could be 750 or 770, with same ARCNUM (or family
identifier which is unfortunate). The existing arc_cpu_tbl[] kept a single
concatenated string for core name and release which thus doesn't work
for 750 vs. 770 identification.
So split this into 2 tables, one with core names and other with release.
And while we are at it, get rid of the range checking for family numbers.
We just document the known to exist cores running Linux and ditch
others.
With this in place, we add detection of ARC750 which is
- cores 0x33 and before
- cores 0x34 and later with MMUv2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This came to light when helping a customer with oldish ARC750 core who
were getting instruction errors because of lack of SWAPE but boot log
was incorrectly printing it as being present
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On older arc700 cores, some of the features configured were not present
in Build config registers. To print about them at boot, we just use the
Kconfig option i.e. whether linux is built to use them or not.
So yes this seems bogus, but what else can be done. Moreover if linux is
booting with these enabled, then the Kconfig info is a good indicator
anyways.
Over time these "hacks" accumulated in read_arc_build_cfg_regs() as well
as arc_cpu_mumbojumbo(). so refactor and move all of those in a single
place: read_arc_build_cfg_regs(). This causes some code redcution too:
| bloat-o-meter2 arch/arc/kernel/setup.o.0 arch/arc/kernel/setup.o.1
| add/remove: 0/0 grow/shrink: 2/1 up/down: 64/-132 (-68)
| function old new delta
| setup_processor 610 670 +60
| cpuinfo_arc700 76 80 +4
| arc_cpu_mumbojumbo 752 620 -132
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously we would not print the case when IOC existed but was not
enabled.
And while at it, reduce one line off boot printing by consolidating
the Peripheral address space and IO-Coherency which in a way
applies to them
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Older ARC700 cores (ARC750 specifically) lack instructions to implement
atomic r-w-w. This is problematic for userspace libraries such as NPTL
which need atomic primitives. So enable them by providing kernel assist.
This is costly but really the only sane soluton (othern than tight
spinning using the otherwise availiable atomic exchange EX instruciton).
Good thing is there are only a few of these cores running Linux out in
the wild.
This only works on UP systems.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
num_possible_cpus() returns how many CPUs may be present on system.
However we want the highest possible CPU number.
This may be differ in a sparsed possible CPUs map.
Such map achived by OF for plat-eznps.
For example if we have:
possible cpus mask 0,3
Then:
num_possible_cpus() is equal 2
while
nr_cpu_ids is equal 4.
Only for value 4 c_start() will provide correct cpuinfo at procfs.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The IDU intc is technically part of MCIP (Multi-core IP) hence
historically was only available in a SMP hardware build (and thus only
in a SMP kernel build). Now that hardware restriction has been lifted,
so a UP kernel needs to support it.
This requires breaking mcip.c into parts which are strictly SMP
(inter-core interrupts) and IDU which in reality is just another
intc and thus has no bearing on SMP.
This change allows IDU in UP builds and with a suitable device tree, we
can have the cascaded intc system
ARCv2 core intc <---> ARCv2 IDU intc <---> periperals
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative. Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".
We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.
This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.
Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the end of "arc_init_IRQ" STATUS32.IE flag is going to be affected by
"flag" instruction but "flag" never touches IE flag on ARCv2. So "kflag"
instruction must be used instead of "flag".
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Cc: stable@vger.kernel.org #4.2+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to keep the .exit.* sections as linker would fail in final link
due to references from .debug_frame which itself could not be discardrd
due to the forced "write,alloc" attributes for it.
| LD init/built-in.o
| `.exit.text' referenced in section `.debug_frame' of arch/arc/built-in.o: defined in discarded section `.exit.text' of arch/arc/built-in.o
| Makefile:949: recipe for target 'vmlinux' failed
With .debug_frame now retired, this hack is no longer needed.
kernel binary is now a little bit smaller as well.
closes STAR 9000549913
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This uses a new set of annoations viz. ENTRY_CFI/END_CFI to enabel cfi
ops generation.
Note that we didn't change the normal ENTRY/EXIT as we don't actually
want unwind info in the trap/exception/interrutp handlers which use
these, as unwinder then gets confused (it keeps recursing vs. stopping).
Semantically these are leaf routines and unwinding should stop when it
hits those routines.
Before
------
28.52% 1.19% 9929 hackbench libuClibc-1.0.17.so [.] __write_nocancel
|
---__write_nocancel
|--8.95%--EV_Trap
| --8.25%--sys_write
| |--3.93%--sock_write_iter
...
|--2.62%--memset <==== [LEAF entry as no unwind info]
^^^^^^
After
-----
29.46% 1.24% 13622 hackbench libuClibc-1.0.17.so [.] __write_nocancel
|
---__write_nocancel
|--9.31%--EV_Trap
| --8.62%--sys_write
| |--4.17%--sock_write_iter
...
|--6.19%--sys_write
| --6.19%--sock_write_iter
| unix_stream_sendmsg
| |--1.62%--sock_alloc_send_pskb
| |--0.89%--sock_def_readable
| |--0.88%--_raw_spin_unlock_irqrestore
| |--0.69%--memset
| | ^^^^^^ <==== [now in proper callframe]
| |
| --0.52%--skb_copy_datagram_from_iter
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This essentially removes ENTRY() assembler annotation for this symbol
since it didn't have a pairing END()
This in ahead of introducing cfi pseudo ops in ENTRY/END which expects
paired cfi_startproc/cfi_endproc
| ../arch/arc/kernel/entry.S: Assembler messages:
| ../arch/arc/kernel/entry.S:270: Error: previous CFI entry not closed (missing .cfi_endproc)
| ../scripts/Makefile.build:326: recipe for target 'arch/arc/kernel/entry-arcv2.o' failed
| make[4]: *** [arch/arc/kernel/entry-arcv2.o] Error 1
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Linus Torvalds