While setting the time, the RTC TIME register should not be accessed.
However due to hardware constraints, setting the RTC time involves
sleeping during 100ms. This sleep was done outside the critical section
protected by the spinlock, so it was possible to read the RTC TIME
register and get an incorrect value. This patch introduces a mutex for
protecting the RTC TIME access, unlike the spinlock it is allowed to
sleep in a critical section protected by a mutex.
The RTC STATUS register can still be used from the interrupt handler but
it has no effect on setting the time.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org> [4.0]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a basic driver for the ultra-low-power Abracon AB x80x series of RTC
chips. It supports in particular, the supersets AB0805 and AB1805.
It allows reading and writing the time, and enables the supercapacitor/
battery charger.
[arnd@arndb.de: abx805 depends on i2c]
[alexandre.belloni@free-electrons.com: renam buffer from date to buf in abx80x_rtc_read_time()]
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ST's Low Power Controller (LPC) controls two devices; watchdog and RTC.
Only one of the devices can be used at any one time. This is enforced
by the correlating MFD driver. This portion of the driver-set controls
the Real Time Clock.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change the __raw IO calls to readl/write_relaxed which makes the driver
endian agnostic to run properly on big endian systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Andrew Victor <linux@maxim.org.za>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC driver supports two flavors of S5M devices: S5M8767-like and
S2MPS14-like.
On S2MPS13 and S2MPS14 devices the RTC module is the same so we want to
re-use the existing support of S2MPS14. However device type was passed
from parent MFD driver in platform data structure. This way for the
S2MPS13 device the main MFD driver passed device type of 'S2MPS13X'.
Instead decouple detecting of device type between main MFD and RTC driver.
This allows adding support for other S2MPS14 variations (like S2MPS11 and
S2MPS13) easily by adding to mfd/sec-core.c:
static const struct mfd_cell s2mps13_devs[] = {
{ .name = "s2mps14-rtc", }
};
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hym8563 datasheet describes the clock output control-bit as "when set
to logic 0, the square wave output is enable, when set to logic 1, the
CLKOUT output is inhibited". But in reality the setting is exactly
opposite.
Before now, the clock output was not really used, but on the rk3288 soc
this generated clock is used to supply the temperature sensor block and
the swapped bit value prevented it from working. With the corrected
value, the tsadc now reports correct values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s3c_rtc_gettime() already returns the result of rtc_valid_tm() on the
obtained time so get rid of another call to rtc_valid_tm().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTC is present in AM43xx and DRA7xx also. Updating the Kconfig to depend
on ARCH_OMAP or ARCH_DAVINCI
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTC module contains a kicker mechanism to prevent any spurious writes from
changing the register values. This mechanism requires two MMR writes to
the KICK0 and KICK1 registers with exact data values before the kicker
lock mechanism is released.
Currently the driver release the lock in the probe and leaves it enabled
until the rtc driver removal. This eliminates the idea of preventing
spurious writes when RTC driver is loaded. So implement rtc lock and
unlock functions before and after register writes.
This is as advised by Paul to implement lock and unlock functions in the
driver and not to unlock and leave it in probe. The same discussion can
be seen here:
http://www.mail-archive.com/linux-omap%40vger.kernel.org/msg111588.html
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use function name in the error log instead of __FILE__.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__rtc_read_time logs should be debug logs instead of error logs.
For example, when the RTC clock is not set, it's not really useful
to print a kernel error log every time someone tries to read the clock:
~ # hwclock -r
[ 604.508263] rtc rtc0: read_time: fail to read
hwclock: RTC_RD_TIME: Invalid argument
If there's a real error, it's likely that lower level or higher level
code will tell it anyway. Make these logs debug logs, and also print
the error code for the read failure.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some error cases RTC name is used before it is initialized:
rtc-rs5c372 0-0032: clock needs to be set
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.6
rtc (null): read_time: fail to read
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
Fix by initializing the name early.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The S2MPS13 RTC is almost the same as S2MPS14. The differences when
updating alarm are:
1. Set WUDR+AUDR field instead of WUDR+RUDR.
2. Clear the AUDR field later (it is not auto-cleared).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add driver for the RTC hardware block on the Conexant CX92755 SoC, from
the Digicolor series of SoCs. Tested on the Equinox evaluation board for
the CX92755 chip.
[akpm@linux-foundation.org: build command arrays at compile-time]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the clock is disabled, do not return a rate of 0 but instead return
the rate the clock will be running at after it gets enabled. This
prevents problems when the core clock code is trying to determine a
suitable rate, while the clock is still off.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC is in a different clock domain so a quick read after write
can retrieve a mangled value of the old/new values
Signed-off-by: Adam Ward <adam.ward.opensource@diasemi.com>
Tested-by: Adam Ward <adam.ward.opensource@diasemi.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two minor sparse warnings:
CHECK drivers/rtc/rtc-ds1685.c
drivers/rtc/rtc-ds1685.c:2178:1: warning: function 'ds1685_rtc_poweroff' with external linkage has definition
drivers/rtc/rtc-ds1685.c:802:23: warning: Using plain integer as NULL pointer
Fixes: aaaf5fbf56 ("rtc: add driver for DS1685 family of real time clocks")
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc driver core now sets the platform_driver 'owner' property, so
remove the assignment from the DS1685 driver.
Fixes: aaaf5fbf56f1: "rtc: add driver for DS1685 family of real time clocks"
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current functions in s3c-rtc driver execute clk_enable/disable() to
control clocks and some functions execute s3c_rtc_alarm_clk_enable()
unnecessarily. So this patch deletes the duplicate clock control and
spilts s3c_rtc_alarm_clk_enable() out as
s3c_rtc_enable_clk()/s3c_rtc_disable_clk() to improve readability.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using device trees on the ARM platform, it is not certain at compile
time whether or not the system will have a RTC.
If one enables CONFIG_HCTOSYS just in case the system booted has a RTC,
and it turns out not to be, this will result in a big fat "unable to open
rtc device" error being printed to console, even when "quiet" is set in
the kernel cmdline.
Fix this by outputting the message with loglevel info instead.
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Despite its name, sign_extend32() is safe to use for 8 bit types too.
(See https://lkml.org/lkml/2015/1/18/289).
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set the of_match_table for this driver so that devices can be described in
the device tree. This device is used in the Trimslice and is already
defined in the Trimslice device tree.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc's status register allows to determine if a 32k crystal is
connected to keep the rtc running in low power states provided the
corresponding fuse bits were blown correctly during production. (In case
they were not, the right frequency can be stated in the device tree.) If
there is no such crystal available force the 24 MHz XTAL clock to keep
running to retain the right date and time. Otherwise use the crystal to
save some power.
It would be nice to only switch to the crystal when the XTAL clock is
about to be disabled and keep the crystal off when unneeded because XTAL
is always on while the chip is powered on. But as sudden power loss isn't
detectable this is not save.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit does not change any logic here. It just makes the code easier
to read.
This is how it looked like:
If err != 0 return err;
else return 0;
Signed-off-by: Robert Kmiec <robert.r.kmiec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
If a system does not provide a persistent_clock(), the time
will be updated on resume by rtc_resume(). With the addition
of the non-stop clocksources for suspend timing, those systems
set the time on resume in timekeeping_resume(), but may not
provide a valid persistent_clock().
This results in the rtc_resume() logic thinking no one has set
the time and it then will over-write the suspend time again,
which is not necessary and only increases clock error.
So, fix this for rtc_resume().
This patch also improves the name of persistent_clock_exist to
make it more grammatical.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-19-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
rtc_read_time() has already judged valid tm by rtc_valid_tm(),
so just remove it.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-17-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has a number of y2038/y2106 issues.
This patch resolves them by:
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
- Replacing rtc_tm_to_time() with rtc_tm_to_time64()
- Changing mxc_rtc_set_mmss() to use rtc_class_ops's set_mmss64()
After this patch, the driver should not have any remaining
y2038/y2106 issues.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-14-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We want to convert mxc_rtc_set_mmss() to use rtc_class_ops's
set_mmss64(), but it uses get_alarm_or_time()/set_alarm_or_time()
internal interfaces which are y2038 unsafe.
So here as a separate patch, it converts these two internal
interfaces of "mxc" to use safe time64_t to make some
preparations.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-13-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
rtc_class_ops's set_alarm() shouldn't deal with the alarm date,
as this is handled in the rtc core.
See rtc_dev_ioctl()'s RTC_ALM_SET and RTC_WKALM_SET cases.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-12-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has a number of y2038/y2106 issues.
This patch resolves them by:
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
- Changing mc13xxx_rtc_set_mmss() to use rtc_class_ops's set_mmss64()
After this patch, the driver should not have any remaining
y2038/y2106 issues.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-11-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has a number of y2038/y2106 issues.
This patch resolves them by:
- Replacing rtc_tm_to_time() with rtc_tm_to_time64()
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
- Changing ab3100_rtc_set_mmss() to use rtc_class_ops's set_mmss64()
After this patch, the driver should not have any remaining
y2038/y2106 issues.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-10-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has a number of y2038/y2106 issues.
This patch resolves them by:
- Replacing get_seconds() with ktime_get_real_seconds()
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
Also add test_rtc_set_mmss64() for testing rtc_class_ops's
set_mmss64(), which can be activated by "test_mmss64" module
parameter.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-9-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently the rtc_class_op's set_mmss() function takes a 32-bit
second value (on 32-bit systems), which is problematic for dates
past y2038.
This patch provides a safe version named set_mmss64() using
y2038 safe time64_t.
After this patch, set_mmss() is deprecated and all its users
will be fixed to use set_mmss64(), it can be removed when having
no users.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
[jstultz: Add whitespace fix for checkpatch]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-8-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As part of addressing in-kernel y2038 issues, this patch adds
update_persistent_clock64() and replaces all the call sites of
update_persistent_clock() with this function. This is a __weak
implementation, which simply calls the existing y2038 unsafe
update_persistent_clock().
This allows architecture specific implementations to be
converted independently, and eventually y2038-unsafe
update_persistent_clock() can be removed after all its
architecture specific implementations have been converted to
update_persistent_clock64().
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-4-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Moorestown RTC driver implements suspend and resume callbacks and
assigns them to the suspend and resume fields of the device_driver
struct. These callbacks are never actually called by anything though.
Modify the driver to properly use dev_pm_ops so that the suspend and
resume functions are actually executed upon suspend/resume.
[akpm@linux-foundation.org: device_driver.name is const char *]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Feng Tang <feng.tang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a typo here so we deadlock.
Fixes: dd1f1f391d ('rtc: at91rm9200: rework wakeup and interrupt handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit df9e26d093 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
added an "rtc_src" DT property to specify the clock used as a source to
the S3C real-time clock.
Not all SoCs needs this so commit eaf3a65908 ("drivers/rtc/rtc-s3c.c:
fix initialization failure without rtc source clock") changed to check
the struct s3c_rtc_data .needs_src_clk to conditionally grab the clock.
But that commit didn't update the data for each IP version so the RTC
broke on the boards that needs a source clock. This is the case of at
least Exynos5250 and Exynos5440 which uses the s3c6410 RTC IP block.
This commit fixes the S3C rtc on the Exynos5250 Snow and Exynos5420
Peach Pit and Pi Chromebooks.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Tyler Baker <tyler.baker@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds