This reverts commit d2487cb425.
Russell King points out that it's obviously bogus, and I have to agree.
Not only does "irq" not even exist in that scope, but we obviously need
to free the irq that we actually requested, and that's IRQ_USB.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>,
Cc: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this fixes the spinlock recursion issue. The older fix was incomplete.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I get following warnings on spar64:
Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd]
Despite of the comment in the patched code, the type cast used there
does make unaligned access. The fix was made as it's done in
ohci-hub.c.
Signed-off-by: Max Dmitrichenko <dmitrmax@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.
From: Gard Spreemann <spreeman@stud.ntnu.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter:
> Hi Greg
>
> 34ef50e5b1 is definitely
> the source of the problem. Reverting that makes the
> ftdi port show up as ttyUSB0 again for me and it
> can actually be opened.
This patch should fix the issue.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Craig Schlenter <craig@codefountain.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:
Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem. Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.
With the attached patch, the RTS/DTR lines are resetted on a close. The
code was mainly taken from the option.c driver.
Convert all the port specific code in attach / shutdown to use the new
port_probe / port_register callbacks from device_register /
device_unregister allowing adding the sysfs attributes to be added at
the correct time and to the serial port device itself, instead of to
the unadorned usb device, avoiding a NULL dereference.
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ensure that the ->port_remove() callbacks get called before the
->shutdown() callback which makeing the order symmetric with
->attach() being called before ->port_probe().
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've developed some devices with FTDI chips (FT232xx). FTDI was so kind
to give some own PID's which I can use together with their VID. Some of
the devices are already very popular here and I have customers from
universities, institutes .....
I use the FTDI VID 0x0403. My PID's are:
0xff38 - IBS US485 (USB<-->RS422/485 interface)
0xff39 - IBS PIC-Programmer
0xff3a - IBS Card reader for PCMCIA SRAM-cards
0xff3b - IBS PK1 - Particel counter
0xff3c - IBS RS232 - Monitor
0xff3d - APP 70 (dust monitoring system)
0xff3e - IBS PEDO-Modem (RF modem 868.35 MHz)
0xff3f - future device
The company is "IBS Ing.-Buero Schleusener".
From: Thomas Schleusener <thomas@be-schl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here are two new device IDs for the cp2101 driver.
The diff is with linus's tree as of this evending.
From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flaky hardware can cause a lot of debounce failed messages. To limit
the performance impact, a ratelimit should be used.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes last use of hardcoded number of irq to
use platfrom_get_irq.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as863) fixes a problem encountered sometimes when resuming
a port on a UHCI controller. The hardware may turn off the
Resume-Detect bit before turning off the Suspend bit, leading usbcore
to think that the port is still suspended and the resume has failed.
The patch makes uhci_finish_suspend() wait until both bits are safely
off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as862) fixes a couple of bugs in the way usbcore handles
intervals for interrupt URBs. usb_interrupt_msg (and usb_bulk_msg for
backward compatibility) don't set the interval correctly for
high-speed devices. proc_do_submiturb() doesn't set it correctly when
a bulk URB is submitted to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is deep architecture specific magic and does should not to exist
in a driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an usual_devs entry for the Nokia 6288. Originally from
Andrew with a re-diff by Phil.
From: Andrew Nayenko <relan@bk.ru>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the duplicate supertop entries that made it into the
.21 rc kernels.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rename the driver struct used with at91_udc to prevent yet another
bogus warning from "modpost".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replacing use of UTS_RELEASE with utsname()->release avoids that the
usb-storage driver is recompiled each time the kernel version changes.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put all Code Mercenaries (VID 0x07c0) IOWarriors (PIDs 0x1500 to 0x15ff) on
the HID blacklist. The range of PIDs has been reserved for IOWarriors. Only
5 PIDs are really used yet.
Signed-off-by: Robert Marquardt <marquardt@codemercs.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Dongle shipped with Logitech DiNovo Edge (0x046d/0xc714) behaves in a weird
non-standard way - it contains multiple reports with the same usage, which
results in remapping of GenericDesktop.X and GenericDesktop.Y usages to
GenericDesktop.Z and GenericDesktop.RX respectively, thus rendering the
touchwheel unusable.
The commit 3506897691 solved this
in a way that it didn't remap certain usages. This however breaks
(at least) middle button of Logic3 / SpectraVideo (0x1267/0x0210),
which in contrary requires the remapping.
To make both of the harware work, allow remapping of these usages again,
and introduce a quirk for Logitech DiNovo Edge "touchwheel" instead - we
disable remapping for key, abs and rel events only for this hardware.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch makes extra keys (F1-F12 in special mode, zooming, rotate, shuffle)
on Logitech S510 keyboard work.
Logitech S510 keyboard sends in report no. 3 keys which are far above the
logical maximum described in descriptor for given report.
This patch introduces a HID quirk for this wireless USB receiver/keyboard
in order to fix the report descriptor before it's being parsed - the logical
maximum and the number of usages is bumped up to 0x104d). The values are in the
"Reserved" area of consumer HUT, so HID_MAX_USAGE had to be changed too.
In addition to proper extracting of the values from report descriptor, proper
HID-input mapping is introduced for them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Report descriptor should be output when CONFIG_HID_DEBUG is defined.
This also mitigates the need for DEBUG and DEBUG_DATA defines, so let's
remove them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB vendor and product IDs are not byteswapped appropriately, and
thus come out in the wrong endianness when fetched through the evdev
using ioctl() on big endian platforms.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as861) adds sysfs attributes to expose the autosuspend
delay value for each USB device. If the user changes the delay from 0
(no autosuspend) to a positive value, an autosuspend is attempted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as859) makes the default USB autosuspend delay a module
parameter of usbcore. By setting the delay value at boot time, users
will be able to prevent the system from autosuspending devices which
for some reason can't handle it.
The patch also stores the autosuspend delay as a per-device value. A
later patch will allow the user to change the value, tailoring the
delay for each individual device. A delay value of 0 will prevent
autosuspend.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as858) makes some minor cleanups to sysfs.c in usbcore.
Unnecessary tests are removed and a few temp variables are added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a blacklist to the USB core to handle some autosuspend and
string issues that devices have.
Originally written by Oliver, but hacked up a lot by Greg.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I don't think the current code works with multiple iovecs.
The original would just copy the first part of priv->buf
over and over into multiple iovecs.
Signed-off-by: Sarah Bailey <saharabeara@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The below patch proposes to use USB defines (defined in linux/hid.h)
instead of just plain numbers in the USB_INTERFACE_INFO statements.
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to add the VID and PID for Telldus Technologies Homeautomation
usb-dongle to the ftdi_sio driver.
From: Micke Prag <micke.prag@telldus.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as856) attempts to improve the performance of uhci-hcd by
removing the asynchronous skeleton Queue Headers. They don't contain
any useful information but the controller has to read through them at
least once every millisecond, incurring a non-zero DMA overhead.
Now all the asynchronous queues are combined, along with the period-1
interrupt queue, into a single list with a single skeleton QH. The
start of the low-speed control, full-speed control, and bulk sublists
is determined by linear search. Since there should rarely be more
than a couple of QHs in the list, the searches should incur a much
smaller total load than keeping the skeleton QHs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as855) adds some convenience macros to uhci-hcd, to help
simplify the code for computing hardware DMA pointers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a driver for the Davicom DM9601 USB 1.1 10/100Mbps
ethernet adaptor using the usbnet framework.
See http://www.davicom.com.tw/eng/products/dm9601.htm for details.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add device IDs for the JVC-PRX1 port replicator. Additionally cleans up
the tabs on a few of other IDs in the list.
Reported by: Reuben Thomas <rrt@sc3d.org>
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mon_bin_exit() and mon_text_exit() are called from __init code, so don't mark
them as __exit.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ioctl is commented out for now, until we verify some userspace
application issues.
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Robert Marquardt <marquardt@codemercs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds all of the known Option device ids to the driver.
Many thanks to some Option engineers for getting me this list.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need to have two tables with the same device ids in it.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Per device data such as brightness belongs to the indivdual device
and should therefore be separate from the the backlight operation
function pointers. This patch splits the two types of data and
allows simplifcation of some code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
backlight_device->sem has a very specific use as documented in the
header file. The external users of this are using it for a different
reason, to serialise access to the update_status() method.
backlight users were supposed to implement their own internal
serialisation of update_status() if needed but everyone is doing
things differently and incorrectly. Therefore add a global mutex to
take care of serialisation for everyone, once and for all.
Locking for get_brightness remains optional since most users don't
need it.
Also update the lcd class in a similar way.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Linus Torvalds