Move data load into a separate function and separate it from
packet length checks of legacy I/O. This makes the code more
readable and easier to reuse.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sizes of fields in struct xdp_md/xdp_buff and some in sk_buff depend
on target architecture. Take that into account and use struct xdp_buff,
not struct xdp_md.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF is host-endian specific. Translating both BE and LE eBPF
to the NFP is feasible, but would require quite a bit of indirection.
The fact that I don't have access to any BE hosts that would fit
a 25G/40G/100G NIC is also limiting my ability to test big endian.
For now restrict the offload to little endian hosts only.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement byte swaps with rotations, shifts and byte loads.
Remember to clear upper parts of the 64 bit registers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register move operation is encoded as alu no op. This means
that one has to specify number of unused/none parameters to
the emit_alu(). Add a helper.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have BPF assemebler support in LLVM 6 we can easily
test all compare instructions (LLVM 4 didn't generate most of them
from C). Fix the compare to immediates and refactor the order
of compare to regs to make sure they both follow the same pattern.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We optimize comparisons to immediate 0 as if (reg.lo | reg.hi).
The early return statement was missing, however, which means we
would generate two comparisons - optimized one followed by a
normal 2x 32 bit compare.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ld_field instruction has the following format in NFP assembler:
ld_field[dst, 1000, src, <<24]
reoder parameters to emit_ld_field_any() to make it closer to
the familiar assembler order.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a simplified is_valid_access() callback when verifier
is used for program analysis by non-host JITs. This allows
us to teach the verifier about packet start and packet end
offsets for direct packet access.
We can extend the callback as needed but for most packet
processing needs there isn't much more the offloads may
require.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Improvements for multi-queuing and for AVB
Two improvements for stmmac: First one corrects the available fifo
size per queue, second one corrects enabling of AVB queues. More info
in commit log.
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Changes from v1:
- Fix typo in second patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Flow control must be disabled for AVB enabled queues and TX
AVB queues must be enabled by setting BIT(2) of TXQEN.
Correct this by passing the queue mode to DMA callbacks
and by checking in these functions wether we are in AVB
performing the necessary adjustments.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are using all the available fifo size in RQS and
TQS fields. This will not work correctly in multi-queues IP's
because total fifo size must be splitted to the enabled queues.
Correct this by computing the available fifo size per queue and
setting the right value in TQS and RQS fields.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ICMP implementation currently replies to an ICMP time exceeded message
(type 11) with an ICMP host unreachable message (type 3, code 1).
However, time exceeded messages can either represent "time to live exceeded
in transit" (code 0) or "fragment reassembly time exceeded" (code 1).
Unconditionally replying to "fragment reassembly time exceeded" with
host unreachable messages might cause unjustified connection resets
which are now easily triggered as UFO has been removed, because, in turn,
sending large buffers triggers IP fragmentation.
The issue can be easily reproduced by running a lot of UDP streams
which is likely to trigger IP fragmentation:
# start netserver in the test namespace
ip netns add test
ip netns exec test netserver
# create a VETH pair
ip link add name veth0 type veth peer name veth0 netns test
ip link set veth0 up
ip -n test link set veth0 up
for i in $(seq 20 29); do
# assign addresses to both ends
ip addr add dev veth0 192.168.$i.1/24
ip -n test addr add dev veth0 192.168.$i.2/24
# start the traffic
netperf -L 192.168.$i.1 -H 192.168.$i.2 -t UDP_STREAM -l 0 &
done
# wait
send_data: data send error: No route to host (errno 113)
netperf: send_omni: send_data failed: No route to host
We need to differentiate instead: if fragment reassembly time exceeded
is reported, we need to silently drop the packet,
if time to live exceeded is reported, maintain the current behaviour.
In both cases increment the related error count "icmpInTimeExcds".
While at it, fix a typo in a comment, and convert the if statement
into a switch to mate it more readable.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using 'ethtool -L' on a VF to change number of requested queues
from PF, we shouldn't trust the VF to reset itself after making the
request. Doing it that way opens the door for a potentially malicious
VF to do nasty things to the PF which should never be the case.
This makes it such that after VF makes a successful request, PF will
then reset the VF to institute required changes. Only if the request
fails will PF send a message back to VF letting it know the request was
unsuccessful.
Testing-hints:
There should be no real functional changes. This is simply hardening
against a potentially malicious VF.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When querying the NVM for supported phy_types, on some firmware
versions, we were failing to actually fill out the phy_types which means
ethtool wouldn't report any link types.
Testing-hints:
Check 'ethtool <iface>' if you have the right (wrong?) firmware.
Without this patch, no link modes will be reported.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't populate const array patterns on the stack, instead make it
static. Makes the object code smaller by over 60 bytes:
Before:
text data bss dec hex filename
1953 496 0 2449 991 i40e_diag.o
After:
text data bss dec hex filename
1798 584 0 2382 94e i40e_diag.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables setting up maximum Tx rates for the traffic
classes in i40e. The maximum rate is offloaded to the hardware through
the mqprio framework by specifying the mode option as 'channel' and
shaper option as 'bw_rlimit' and is configured for the VSI. Configuring
minimum Tx rate limit is not supported in the device. The minimum
usable value for Tx rate is 50Mbps.
Example:
# tc qdisc add dev eth0 root mqprio num_tc 2 map 0 0 0 0 1 1 1 1\
queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\
max_rate 4Gbit 5Gbit
To dump the bandwidth rates:
# tc qdisc show dev eth0
qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0
queues:(0:3) (4:7)
mode:channel
shaper:bw_rlimit max_rate:4Gbit 5Gbit
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the BW rate limiting for Tx traffic
on the VF to be reused in the next patch for rate limiting Tx
traffic for the VSIs on the PF as well.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver is modified to enable the new mqprio hardware
offload mode and factor the TCs and queue configuration by
creating channel VSIs. In this mode, the priority to traffic
class mapping and the user specified queue ranges are used
to configure the traffic classes by setting the mode option to
'channel'.
Example:
map 0 0 0 0 1 2 2 3 queues 2@0 2@2 1@4 1@5\
hw 1 mode channel
qdisc mqprio 8038: root tc 4 map 0 0 0 0 1 2 2 3 0 0 0 0 0 0 0 0
queues:(0:1) (2:3) (4:4) (5:5)
mode:channel
shaper:dcb
The HW channels created are removed and all the queue configuration
is set to default when the qdisc is detached from the root of the
device.
This patch also disables setting up channels via ethtool (ethtool -L)
when the TCs are configured using mqprio scheduler.
The patch also limits setting ethtool Rx flow hash indirection
(ethtool -X eth0 equal N) to max queues configured via mqprio.
The Rx flow hash indirection input through ethtool should be
validated so that it is within in the queue range configured via
tc/mqprio. The bound checking is achieved by reporting the current
rss size to the kernel when queues are configured via mqprio.
Example:
map 0 0 0 1 0 2 3 0 queues 2@0 4@2 8@6 11@14\
hw 1 mode channel
Cannot set RX flow hash configuration: Invalid argument
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets up the infrastructure for offloading TCs and
queue configurations to the hardware by creating HW channels(VSI).
A new channel is created for each of the traffic class
configuration offloaded via mqprio framework except for the first TC
(TC0). TC0 for the main VSI is also reconfigured as per user provided
queue parameters. Queue counts that are not power-of-2 are handled by
reconfiguring RSS by reprogramming LUTs using the queue count value.
This patch also handles configuring the TX rings for the channels,
setting up the RX queue map for channel.
Also, the channels so created are removed and all the queue
configuration is set to default when the qdisc is detached from the
root of the device.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce a macro for the bit setting the PF reset flag and
update its usages. This makes it easier to use this flag
in functions to be introduced in future without encountering
checkpatch issues related to alignment and line over 80
characters.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The offload types currently supported in mqprio are 0 (no offload) and
1 (offload only TCs) by setting these values for the 'hw' option. If
offloads are supported by setting the 'hw' option to 1, the default
offload mode is 'dcb' where only the TC values are offloaded to the
device. This patch introduces a new hardware offload mode called
'channel' with 'hw' set to 1 in mqprio which makes full use of the
mqprio options, the TCs, the queue configurations and the QoS parameters
for the TCs. This is achieved through a new netlink attribute for the
'mode' option which takes values such as 'dcb' (default) and 'channel'.
The 'channel' mode also supports QoS attributes for traffic class such as
minimum and maximum values for bandwidth rate limits.
This patch enables configuring additional HW shaper attributes associated
with a traffic class. Currently the shaper for bandwidth rate limiting is
supported which takes options such as minimum and maximum bandwidth rates
and are offloaded to the hardware in the 'channel' mode. The min and max
limits for bandwidth rates are provided by the user along with the TCs
and the queue configurations when creating the mqprio qdisc. The interface
can be extended to support new HW shapers in future through the 'shaper'
attribute.
Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading
mqprio queue options and use this to be shared between the kernel and
device driver. This contains a copy of the existing data structure
for mqprio queue options. This new data structure can be extended when
adding new attributes for traffic class such as mode, shaper, shaper
parameters (bandwidth rate limits). The existing data structure for mqprio
queue options will be shared between the kernel and userspace.
Example:
queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\
min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit
To dump the bandwidth rates:
qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0
queues:(0:3) (4:7)
mode:channel
shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jon Maloy says:
====================
tipc: Introduce Communcation Group feature
With this commit series we introduce a 'Group Communication' feature in
order to resolve the datagram and multicast flow control problem. This
new feature makes it possible for a user to instantiate multiple private
virtual brokerless message buses by just creating and joining member
sockets.
The main features are as follows:
---------------------------------
- Sockets can join a group via a new setsockopt() call TIPC_GROUP_JOIN.
If it is the first socket of the group this implies creation of the
group. This call takes four parameters: 'type' serves as group
identifier, 'instance' serves as member identifier, and 'scope'
indicates the visibility of the group (node/cluster/zone). Finally,
'flags' indicates different options for the socket joining the group.
For the time being, there are only two such flags: 1) 'LOOPBACK'
indicates if the creator of the socket wants to receive a copy of
broadcast or multicast messages it sends to the group, 2) EVENTS
indicates if it wants to receive membership (JOINED/LEFT) events for
the other members of the group.
- Groups are closed, i.e., sockets which have not joined a group will
not be able to send messages to or receive messages from members of
the group, and vice versa. A socket can only be member of one group
at a time.
- There are four transmission modes.
1: Unicast. The sender transmits a message using the port identity
(node:port tuple) of the receiving socket.
2: Anycast. The sender transmits a message using a port name (type:
instance:scope) of one of the receiving sockets. If more than
one member socket matches the given address a destination is
selected according to a round-robin algorithm, but also considering
the destination load (advertised window size) as an additional
criteria.
3: Multicast. The sender transmits a message using a port name
(type:instance:scope) of one or more of the receiving sockets.
All sockets in the group matching the given address will receive
a copy of the message.
4: Broadcast. The sender transmits a message using the primtive
send(). All members of the group, irrespective of their member
identity (instance) number receive a copy of the message.
- TIPC broadcast is used for carrying messages in mode 3 or 4 when
this is deemed more efficient, i.e., depending on number of actual
destinations.
- All transmission modes are flow controlled, so that messages never
are dropped or rejected, just like we are used to from connection
oriented communication. A special algorithm guarantees that this is
true even for multipoint-to-point communication, i.e., at occasions
where many source sockets may decide to send simultaneously towards
the same destination socket.
- Sequence order is always guaranteed, even between the different
transmission modes.
- Member join/leave events are received in all other member sockets
in guaranteed order. I.e., a 'JOINED' (an empty message with the OOB
bit set) will always be received before the first data message from
a new member, and a 'LEAVE' (like 'JOINED', but with EOR bit set) will
always arrive after the last data message from a leaving member.
-----
v2: Reordered variable declarations in descending length order, as per
feedback from David Miller. This was done as far as permitted by the
the initialization order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have point-to-multipoint flow control within a group. But
we even need the opposite; -a scheme which can handle that potentially
hundreds of sources may try to send messages to the same destination
simultaneously without causing buffer overflow at the recipient. This
commit adds such a mechanism.
The algorithm works as follows:
- When a member detects a new, joining member, it initially set its
state to JOINED and advertises a minimum window to the new member.
This window is chosen so that the new member can send exactly one
maximum sized message, or several smaller ones, to the recipient
before it must stop and wait for an additional advertisement. This
minimum window ADV_IDLE is set to 65 1kB blocks.
- When a member receives the first data message from a JOINED member,
it changes the state of the latter to ACTIVE, and advertises a larger
window ADV_ACTIVE = 12 x ADV_IDLE blocks to the sender, so it can
continue sending with minimal disturbances to the data flow.
- The active members are kept in a dedicated linked list. Each time a
message is received from an active member, it will be moved to the
tail of that list. This way, we keep a record of which members have
been most (tail) and least (head) recently active.
- There is a maximum number (16) of permitted simultaneous active
senders per receiver. When this limit is reached, the receiver will
not advertise anything immediately to a new sender, but instead put
it in a PENDING state, and add it to a corresponding queue. At the
same time, it will pick the least recently active member, send it an
advertisement RECLAIM message, and set this member to state
RECLAIMING.
- The reclaimee member has to respond with a REMIT message, meaning that
it goes back to a send window of ADV_IDLE, and returns its unused
advertised blocks beyond that value to the reclaiming member.
- When the reclaiming member receives the REMIT message, it unlinks
the reclaimee from its active list, resets its state to JOINED, and
notes that it is now back at ADV_IDLE advertised blocks to that
member. If there are still unread data messages sent out by
reclaimee before the REMIT, the member goes into an intermediate
state REMITTED, where it stays until the said messages have been
consumed.
- The returned advertised blocks can now be re-advertised to the
pending member, which is now set to state ACTIVE and added to
the active member list.
- To be proactive, i.e., to minimize the risk that any member will
end up in the pending queue, we start reclaiming resources already
when the number of active members exceeds 3/4 of the permitted
maximum.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following scenario is possible:
- A user sends a broadcast message, and thereafter immediately leaves
the group.
- The LEAVE message, following a different path than the broadcast,
arrives ahead of the broadcast, and the sending member is removed
from the receiver's list.
- The broadcast message arrives, but is dropped because the sender
now is unknown to the receipient.
We fix this by sequence numbering membership events, just like ordinary
unicast messages. Currently, when a JOIN is sent to a peer, it contains
a synchronization point, - the sequence number of the next sent
broadcast, in order to give the receiver a start synchronization point.
We now let even LEAVE messages contain such an "end synchronization"
point, so that the recipient can delay the removal of the sending member
until it knows that all messages have been received.
The received synchronization points are added as sequence numbers to the
generated membership events, making it possible to handle them almost
the same way as regular unicasts in the receiving filter function. In
particular, a DOWN event with a too high sequence number will be kept
in the reordering queue until the missing broadcast(s) arrive and have
been delivered.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following scenario is possible:
- A user joins a group, and immediately sends out a broadcast message
to its members.
- The broadcast message, following a different data path than the
initial JOIN message sent out during the joining procedure, arrives
to a receiver before the latter..
- The receiver drops the message, since it is not ready to accept any
messages until the JOIN has arrived.
We avoid this by treating group protocol JOIN messages like unicast
messages.
- We let them pass through the recipient's multicast input queue, just
like ordinary unicasts.
- We force the first following broadacst to be sent as replicated
unicast and being acknowledged by the recipient before accepting
any more broadcast transmissions.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a mechanism guaranteeing that group unicasts sent out from a
socket are not bypassed by later sent broadcasts from the same socket.
We do this as follows:
- Each time a unicast is sent, we set a the broadcast method for the
socket to "replicast" and "mandatory". This forces the first
subsequent broadcast message to follow the same network and data path
as the preceding unicast to a destination, hence preventing it from
overtaking the latter.
- In order to make the 'same data path' statement above true, we let
group unicasts pass through the multicast link input queue, instead
of as previously through the unicast link input queue.
- In the first broadcast following a unicast, we set a new header flag,
requiring all recipients to immediately acknowledge its reception.
- During the period before all the expected acknowledges are received,
the socket refuses to accept any more broadcast attempts, i.e., by
blocking or returning EAGAIN. This period should typically not be
longer than a few microseconds.
- When all acknowledges have been received, the sending socket will
open up for subsequent broadcasts, this time giving the link layer
freedom to itself select the best transmission method.
- The forced and/or abrupt transmission method changes described above
may lead to broadcasts arriving out of order to the recipients. We
remedy this by introducing code that checks and if necessary
re-orders such messages at the receiving end.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group unicast messages don't follow the same path as broadcast messages,
and there is a high risk that unicasts sent from a socket might bypass
previously sent broadcasts from the same socket.
We fix this by letting all unicast messages carry the sequence number of
the next sent broadcast from the same node, but without updating this
number at the receiver. This way, a receiver can check and if necessary
re-order such messages before they are added to the socket receive buffer.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previously introduced message transport to all group members is
based on the tipc multicast service, but is logically a broadcast
service within the group, and that is what we call it.
We now add functionality for sending messages to all group members
having a certain identity. Correspondingly, we call this feature 'group
multicast'. The service is using unicast when only one destination is
found, otherwise it will use the bearer broadcast service to transfer
the messages. In the latter case, the receiving members filter arriving
messages by looking at the intended destination instance. If there is
no match, the message will be dropped, while still being considered
received and read as seen by the flow control mechanism.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit, we make it possible to send connectionless unicast
messages to any member corresponding to the given member identity,
when there is more than one such member. The sender must use a
TIPC_ADDR_NAME address to achieve this effect.
We also perform load balancing between the destinations, i.e., we
primarily select one which has advertised sufficient send window
to not cause a block/EAGAIN delay, if any. This mechanism is
overlayed on the always present round-robin selection.
Anycast messages are subject to the same start synchronization
and flow control mechanism as group broadcast messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now make it possible to send connectionless unicast messages
within a communication group. To send a message, the sender can use
either a direct port address, aka port identity, or an indirect port
name to be looked up.
This type of messages are subject to the same start synchronization
and flow control mechanism as group broadcast messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduce an end-to-end flow control mechanism for group broadcast
messages. This ensures that no messages are ever lost because of
destination receive buffer overflow, with minimal impact on performance.
For now, the algorithm is based on the assumption that there is only one
active transmitter at any moment in time.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like with any other service, group members' availability can be
subscribed for by connecting to be topology server. However, because
the events arrive via a different socket than the member socket, there
is a real risk that membership events my arrive out of synch with the
actual JOIN/LEAVE action. I.e., it is possible to receive the first
messages from a new member before the corresponding JOIN event arrives,
just as it is possible to receive the last messages from a leaving
member after the LEAVE event has already been received.
Since each member socket is internally also subscribing for membership
events, we now fix this problem by passing those events on to the user
via the member socket. We leverage the already present member synch-
ronization protocol to guarantee correct message/event order. An event
is delivered to the user as an empty message where the two source
addresses identify the new/lost member. Furthermore, we set the MSG_OOB
bit in the message flags to mark it as an event. If the event is an
indication about a member loss we also set the MSG_EOR bit, so it can
be distinguished from a member addition event.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With group communication, it becomes important for a message receiver to
identify not only from which socket (identfied by a node:port tuple) the
message was sent, but also the logical identity (type:instance) of the
sending member.
We fix this by adding a second instance of struct sockaddr_tipc to the
source address area when a message is read. The extra address struct
is filled in with data found in the received message header (type,) and
in the local member representation struct (instance.)
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for introducing flow control for multicast and datagram
messaging we need a more strictly defined framework than we have now. A
socket must be able keep track of exactly how many and which other
sockets it is allowed to communicate with at any moment, and keep the
necessary state for those.
We therefore introduce a new concept we have named Communication Group.
Sockets can join a group via a new setsockopt() call TIPC_GROUP_JOIN.
The call takes four parameters: 'type' serves as group identifier,
'instance' serves as an logical member identifier, and 'scope' indicates
the visibility of the group (node/cluster/zone). Finally, 'flags' makes
it possible to set certain properties for the member. For now, there is
only one flag, indicating if the creator of the socket wants to receive
a copy of broadcast or multicast messages it is sending via the socket,
and if wants to be eligible as destination for its own anycasts.
A group is closed, i.e., sockets which have not joined a group will
not be able to send messages to or receive messages from members of
the group, and vice versa.
Any member of a group can send multicast ('group broadcast') messages
to all group members, optionally including itself, using the primitive
send(). The messages are received via the recvmsg() primitive. A socket
can only be member of one group at a time.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We often see a need for a linked list of destination identities,
sometimes containing a port number, sometimes a node identity, and
sometimes both. The currently defined struct u32_list is not generic
enough to cover all cases, so we extend it to contain two u32 integers
and rename it to struct tipc_dest_list.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We see an increasing need to send multiple single-buffer messages
of TIPC_SYSTEM_IMPORTANCE to different individual destination nodes.
Instead of looping over the send queue and sending each buffer
individually, as we do now, we add a new help function
tipc_node_distr_xmit() to do this.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the following commits we will need to handle multiple incoming and
rejected/returned buffers in the function socket.c::filter_rcv().
As a preparation for this, we generalize the function by handling
buffer queues instead of individual buffers. We also introduce a
help function tipc_skb_reject(), and rename filter_rcv() to
tipc_sk_filter_rcv() in line with other functions in socket.c.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the coming commits, functions at the socket level will need the
ability to read the availability status of a given node. We therefore
introduce a new function for this purpose, while renaming the existing
static function currently having the wanted name.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address given to tipc_connect() is not completely sanity checked,
under the assumption that this will be done later in the function
__tipc_sendmsg() when the address is used there.
However, the latter functon will in the next commits serve as caller
to several other send functions, so we want to move the corresponding
sanity check there to the beginning of that function, before we possibly
need to grab the address stored by tipc_connect(). We must therefore
be able to trust that this address already has been thoroughly checked.
We do this in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As preparation for introducing communication groups, we add the ability
to issue topology subscriptions and receive topology events from kernel
space. This will make it possible for group member sockets to keep track
of other group members.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code here (more or less accidentally) tracks the HT capability of
the AP when connected, and we found at least one AP that erroneously
toggles its 20/40 capability bit when changing between 20/40 MHz. The
connection to the AP is then broken because we set the 40 MHz disable
flag based on this, as soon as it switches to 20 MHz, but because the
flag then changed, we disconnect.
I'd be inclined to just ignore this issue, since we then reconnect
while the AP is in 20 MHz mode and never use 40 MHz with it again,
but this code is a bit strange anyway - we don't use the capabilities
for anything else.
Change the code to simply not track the HT capabilities at all, which
assumes that the AP at least sets 20/40 capability when operating in
40 MHz (or higher). If not, rate scaling might end up using only the
narrower bandwidth.
The new behaviour also mirrors what VHT does, where we only check the
VHT operation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The missing CONFIG_ prefix means this macro is never defined,
leading to a possible Kbuild warning:
net/wireless/reg.c:666:20: error: 'load_keys_from_buffer' defined but not used [-Werror=unused-function]
static void __init load_keys_from_buffer(const u8 *p, unsigned int buflen)
When we use the correct symbol, the warning also goes away.
Fixes: 90a53e4432 ("cfg80211: implement regdb signature checking")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Building an allmodconfig kernel with 'make -s' now prints a single line:
GEN net/wireless/shipped-certs.c
Using '$(kecho)' here will skip the output with 'make -s' but
otherwise keeps printing it, which is consistent with how we
handle all the other output.
Fixes: 90a53e4432 ("cfg80211: implement regdb signature checking")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The module clock is used for two purposes:
- Wake-on-LAN (WoL), which is optional,
- gPTP Timer Increment (GTI) configuration, which is mandatory.
As the clock is needed for GTI configuration anyway, WoL is always
available. Hence remove duplication and repeated obtaining of the clock
by making GTI use the stored clock for WoL use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał Miłecki says:
====================
net: support bgmac with B50212E B1 PHY
I got a report that a board with BCM47189 SoC and B50212E B1 PHY doesn't
work well some devices as there is massive ping loss. After analyzing
PHY state it has appeared that is runs in slave mode and doesn't auto
switch to master properly when needed.
This patchset fixes this by:
1) Adding new flag support to the PHY driver for setting master mode
2) Modifying bgmac to request master mode for reported hardware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 4 very similar PHYs:
0x600d84a1: BCM54210E (rev B0)
0x600d84a2: BCM54210E (rev B1)
0x600d84a5: B50212E (rev B0)
0x600d84a6: B50212E (rev B1)
that need setting master mode manually. It's because they run in slave
mode by default with Automatic Slave/Master configuration disabled which
can lead to unreliable connection with massive ping loss.
So far it was reported for a board with BCM47189 SoC and B50212E B1 PHY
connected to the bgmac supported ethernet device. Telling PHY driver to
setup PHY properly solves this issue.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of Broadcom's PHYs run by default in slave mode with Automatic
Slave/Master configuration disabled. It stops them from working properly
with some devices.
So far it has been verified for BCM54210E and BCM50212E which don't
work well with Intel's I217-LM and I218-LM:
http://ark.intel.com/products/60019/Intel-Ethernet-Connection-I217-LMhttp://ark.intel.com/products/71307/Intel-Ethernet-Connection-I218-LM
I was told there is massive ping loss.
This commit adds support for a new flag which can be set by an ethernet
driver to fixup PHY setup.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the underlying master ever changes its L2 (e.g. bonding device),
then make sure that the IPvlan slaves always emit packets with the
current L2 of the master instead of the stale mac addr which was
copied during the device creation. The problem can be seen with
following script -
#!/bin/bash
# Create a vEth pair
ip link add dev veth0 type veth peer name veth1
ip link set veth0 up
ip link set veth1 up
ip link show veth0
ip link show veth1
# Create an IPvlan device on one end of this vEth pair.
ip link add link veth0 dev ipvl0 type ipvlan mode l2
ip link show ipvl0
# Change the mac-address of the vEth master.
ip link set veth0 address 02:11:22:33:44:55
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski