This reverts commit ce78ffa3ef.
Wren and Nicolas reported that ath11k was failing to initialise QCA6390
Wi-Fi 6 device with error:
qcom_mhi_qrtr: probe of mhi0_IPCR failed with error -22
Commit ce78ffa3ef ("net: really fix the build..."), introduced in
v5.14-rc5, caused this regression in qrtr. Most likely all ath11k
devices are broken, but I only tested QCA6390. Let's revert the broken
commit so that ath11k works again.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210826172816.24478-1-kvalo@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MHI reads the channel ID from the event ring element sent by the
device which can be any value between 0 and 255. In order to
prevent any out of bound accesses, add a check against the maximum
number of channels supported by the controller and those channels
not configured yet so as to skip processing of that event ring
element.
Link: https://lore.kernel.org/r/1624558141-11045-1-git-send-email-bbhatt@codeaurora.org
Fixes: 1d3173a3ba ("bus: mhi: core: Add support for processing events from client device")
Cc: stable@vger.kernel.org #5.10
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210716075106.49938-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices such as SDX24 do not have the provision for inband wake
doorbell in the form of channel 127 and instead have a sideband
GPIO for it. Newer devices such as SDX55 or SDX65 support inband
wake method by default. Ensure the functionality is used based on
this such that device wake stays held when a client driver uses
mhi_device_get() API or the equivalent debugfs entry.
Link: https://lore.kernel.org/r/1624560809-30610-1-git-send-email-bbhatt@codeaurora.org
Fixes: e3e5e6508f ("bus: mhi: pci_generic: No-Op for device_wake operations")
Cc: stable@vger.kernel.org #5.12
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210716075106.49938-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MRU value used by the MHI MBIM network interface affects
the throughput performance of the interface. Different modem
models use different default MRU sizes based on their bandwidth
capabilities. Large values generally result in higher throughput
for larger packet sizes.
In addition if the MRU used by the MHI device is larger than that
specified in the MHI net device the data is fragmented and needs
to be re-assembled which generates a (single) warning message about
the fragmented packets. Setting the MRU on both ends avoids the
extra processing to re-assemble the packets.
This patch allows the documented MRU for a modem to be automatically
set as the MHI net device MRU avoiding fragmentation and improving
throughput performance.
Signed-off-by: Richard Laing <richard.laing@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
During system resume, MHI host triggers M3->M0 transition and then waits
for target device to enter M0 state. Once done, the device queues a state
change event into ctrl event ring and notifies MHI host by raising an
interrupt, where a tasklet is scheduled to process this event. In most
cases, the tasklet is served timely and wait operation succeeds.
However, there are cases where CPU is busy and cannot serve this tasklet
for some time. Once delay goes long enough, the device moves itself to M1
state and also interrupts MHI host after inserting a new state change
event to ctrl ring. Later when CPU finally has time to process the ring,
there will be two events:
1. For M3->M0 event, which is the first event to be processed queued first.
The tasklet handler serves the event, updates device state to M0 and
wakes up the task.
2. For M0->M1 event, which is processed later, the tasklet handler
triggers M1->M2 transition and updates device state to M2 directly,
then wakes up the MHI host (if it is still sleeping on this wait queue).
Note that although MHI host has been woken up while processing the first
event, it may still has no chance to run before the second event is
processed. In other words, MHI host has to keep waiting till timeout
causing the M0 state to be missed.
kernel log here:
...
Apr 15 01:45:14 test-NUC8i7HVK kernel: [ 4247.911251] mhi 0000:06:00.0: Entered with PM state: M3, MHI state: M3
Apr 15 01:45:14 test-NUC8i7HVK kernel: [ 4247.917762] mhi 0000:06:00.0: State change event to state: M0
Apr 15 01:45:14 test-NUC8i7HVK kernel: [ 4247.917767] mhi 0000:06:00.0: State change event to state: M1
Apr 15 01:45:14 test-NUC8i7HVK kernel: [ 4338.788231] mhi 0000:06:00.0: Did not enter M0 state, MHI state: M2, PM state: M2
...
Fix this issue by simply adding M2 as a valid state for resume.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Cc: stable@vger.kernel.org
Fixes: 0c6b20a1d7 ("bus: mhi: core: Add support for MHI suspend and resume")
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210524040312.14409-1-bqiang@codeaurora.org
[mani: slightly massaged the commit message]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210621161616.77524-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On graceful power-down/disable transition, when an MHI reset is
performed, the MHI device loses its context, including interrupt
configuration. However, the current implementation is waiting for
event(irq) driven state change to confirm reset has been completed,
which never happens, and causes reset timeout, leading to unexpected
high latency of the mhi_power_down procedure (up to 45 seconds).
Fix that by moving to the recently introduced poll_reg_field method,
waiting for the reset bit to be cleared, in the same way as the
power_on procedure.
Cc: stable@vger.kernel.org
Fixes: a6e2e3522f ("bus: mhi: core: Add support for PM state transitions")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Link: https://lore.kernel.org/r/1620029090-8975-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210621161616.77524-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes crash after resuming from hibernation. The issue
occurs when mhi stack is builtin and so part of the 'restore-kernel',
causing the device to be resumed from 'restored kernel' with a no
more valid context (memory mappings etc...) and leading to spurious
crashes.
This patch fixes the issue by implementing proper freeze/restore
callbacks.
Link: https://lore.kernel.org/r/1622571445-4505-1-git-send-email-loic.poulain@linaro.org
Reported-by: Shujun Wang <wsj20369@163.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210606153741.20725-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Link: https://lore.kernel.org/r/20210413160318.2003699-1-weiyongjun1@huawei.com
Fixes: 8562d4fe34 ("mhi: pci_generic: Add health-check")
Cc: stable <stable@vger.kernel.org>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Hemant kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210606153741.20725-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to MHI v1.1 specification, change the channel name of T99W175
from "AT" to "DUN" (Dial-up networking) for both channel 32 and 33,
so that the channels can be bound to the Qcom WWAN control driver, and
device node such as /dev/wwan0p3DUN will be generated, which is very useful
for debugging modem
Link: https://lore.kernel.org/r/20210429014226.21017-1-jarvis.w.jiang@gmail.com
[mani: changed the dev node to /dev/wwan0p3DUN]
Fixes: aac426562f ("bus: mhi: pci_generic: Introduce Foxconn T99W175 support")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jarvis Jiang <jarvis.w.jiang@gmail.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210606153741.20725-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes below sparse warnings with W=2 about shadow
declarations:
drivers/bus/mhi/core/main.c: In function ‘parse_xfer_event’:
drivers/bus/mhi/core/main.c:667:17: warning: declaration of ‘flags’ shadows a previous local [-Wshadow]
667 | unsigned long flags;
| ^~~~~
drivers/bus/mhi/core/main.c:565:16: note: shadowed declaration is here
565 | unsigned long flags = 0;
| ^~~~~
drivers/bus/mhi/core/main.c: In function ‘mhi_process_ctrl_ev_ring’:
drivers/bus/mhi/core/main.c:856:23: warning: declaration of ‘new_state’ shadows a previous local [-Wshadow]
856 | enum mhi_pm_state new_state;
| ^~~~~~~~~
drivers/bus/mhi/core/main.c:837:19: note: shadowed declaration is here
837 | enum mhi_state new_state;
| ^~~~~~~~~
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
"mhi_controller_config" struct is not modified inside "mhi_pci_dev_info"
struct. So constify the instances.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for T99W175 modems, this modem series is based on SDX55
qcom chip. The modem is mainly based on MBIM protocol for both the
data and control path.
This patch adds support for below modems:
- T99W175(based on sdx55), Both for eSIM and Non-eSIM
- DW5930e(based on sdx55), With eSIM, It's also T99W175
- DW5930e(based on sdx55), Non-eSIM, It's also T99W175
This patch was tested with Ubuntu 20.04 X86_64 PC as host
Signed-off-by: Jarvis Jiang <jarvis.w.jiang@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210408095524.3559-1-jarvis.w.jiang@gmail.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When parsing the structures in the shared memory, there are values which
come from the remote device. For example, a transfer completion event
will have a pointer to the tre in the relevant channel's transfer ring.
As another example, event ring elements may specify a channel in which
the event occurred, however the specified channel value may not be valid
as no channel is defined at that index even though the index may be less
than the maximum allowed index. Such values should be considered to be
untrusted, and validated before use. If we blindly use such values, we
may access invalid data or crash if the values are corrupted.
If validation fails, drop the relevant event.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Link: https://lore.kernel.org/r/1615411855-15053-1-git-send-email-jhugo@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Deinit the device on shutdown to halt MHI/PCI operation on device
side. This change fixes floating device state with some hosts that
do not fully shutdown PCIe device when rebooting.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1616169037-7969-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The __mhi_unprepare_channel() API does not require the __ prefix.
Get rid of it and make the internal function consistent with the
other function names.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Link: https://lore.kernel.org/r/1617311778-1254-9-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
A client can attempt to unprepare certain channels for transfer even
after the execution environment they are supposed to run in has changed.
In the event that happens, the device need not be notified of the reset
and the host can proceed with clean up for the channel context and
memory allocated for it on the host as the device will no longer be able
to respond to such a request.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-8-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When clearing up the channel context after client drivers are
done using channels, the configuration is currently not being
reset entirely. Ensure this is done to appropriately handle
issues where clients unaware of the context state end up calling
functions which expect a context.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-7-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI host can fail early if device is in a bad state by attempting
to assert device wake and holding the runtime PM vote before
sending a channel update command instead of performing a wake
toggle and waiting for a timeout if the send were to fail. This
can help improve the design and enable shorter wait periods for
device to respond as votes are already held.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-6-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Debug messages dealing with client devices use the generic MHI
controller or parent device along with a channel number. It would
be better to instead use the client device directly and enable
better log messages for channel updates.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-5-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Improve the channel handling state machine such that all commands
go through a common function and a validation process to ensure
that the state machine is not violated in any way and adheres to
the MHI specification. Using this common function allows MHI to
eliminate some unnecessary debug messages and code duplication.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-4-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If a channel was explicitly stopped but not reset and a driver
remove is issued, clean up the channel context such that it is
reflected on the device. This move is useful if a client driver
module is unloaded or a device crash occurs with the host having
placed the channel in a stopped state.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-3-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support to allow sending the STOP channel command. If a
client driver would like to STOP a channel and have the device
retain the channel context instead of issuing a RESET to it and
clearing the context, this would provide support for it after
the ability to send this command is exposed to clients.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-2-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Some controllers can choose to skip preparation for power up.
In that case, device context is initialized based on the pre_init
flag not being set during mhi_prepare_for_power_up(). There is no
reason MHI host driver should maintain and provide controllers
with two separate paths for preparing MHI.
Going forward, all controllers will be required to call the
mhi_prepare_for_power_up() API followed by their choice of sync
or async power up. This allows MHI host driver to get rid of the
pre_init flag and sets up a common way for all controllers to use
MHI. This also helps controllers fail early on during preparation
phase in some failure cases.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617313309-24035-1-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since M3 can be entered/exited quite a lot when used for runtime PM,
keep the mhi suspend/resume transitions quiet.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617700315-12492-2-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This change ensures that PM reference is always get during packet
queueing and released either after queuing completion (RX) or once
the buffer has been consumed (TX). This guarantees proper update for
underlying MHI controller runtime status (e.g. last_busy timestamp)
and prevents suspend to be triggered while TX packets are flying,
or before we completed update of the RX ring.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617700315-12492-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In certain devices, it is likely that there is no incoming MHI
interrupt for a transition to MHI READY state. One such example
is the move from Pass Through to an SBL or AMSS execution
environment. In order to facilitate faster bootup times as there
is no need to wait until timeout_ms completes, MHI host can poll
every 25 milliseconds to check if device has entered MHI READY
until a maximum timeout of twice the timeout_ms is reached.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617215665-19593-3-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Introduce helper function to allow MHI core driver to poll for
a value in a register field. This helps reach a common path to
read and poll register values along with a retry time interval.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617215665-19593-2-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As of now abbreviations are being used for many state and
execution environment strings. Improve and expand those such that
debug messages are clear.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1617067704-28850-8-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When moving from SYS_ERROR transition to a different execution
environment, MHI host relies on the BHI register read to spawn
the next image download or wait for READY -> M0 states. The
device can at times move the execution environment to mission
mode when a pass through is expected, which can result in a
stall. Initiate a wait for MHI READY and write M0 such that the
device can proceed with state change event updates for any new
execution environment being entered. This allows us to remove
conditionals in handling firmware load for PBL modes and keeps
the execution environment out of the picture as it can change at
any time.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617067704-28850-7-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI power up can go through an EDL to Flash Programmer path when
the device has a blank NAND. In those cases, mhi_sync_power_up()
can timeout waiting for a mission mode execution environment.
Allow a successful power up instead by identifying Flash
Programmer as a valid mission mode execution environment with a
purpose to flash the device image contents.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1617067704-28850-6-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI WWAN modems support downloading firmware to NAND or eMMC
using Firehose protocol with process as follows:
1. Modem boots up, enters AMSS execution environment and the
device later enters EDL (Emergency Download) mode through any
mechanism host can use such as a diag command.
2. Modem enters SYS_ERROR, MHI host handles SYS_ERROR transition.
3. EDL image for device to enter 'Flash Programmer' execution
environment is then flashed via BHI interface from host.
4. Modem enters MHI READY -> M0 and sends the Flash Programmer
execution environment change to host.
5. Following that, EDL/FIREHOSE channels (34, 35) are made
available from the host.
6. User space tool for downloading firmware image to modem over
the EDL channels using Firehose protocol. Link to USB flashing
tool: https://git.linaro.org/landing-teams/working/qualcomm/qdl.git/
Make the necessary changes to allow for this sequence to occur and
allow using the Flash Programmer execution environment.
Signed-off-by: Carl Yin <carl.yin@quectel.com>
Co-developed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617067704-28850-5-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Device entering EDL or Emergency Download Mode will be in a
SYS_ERROR MHI state. This requires MHI host to proceed with the
EDL image download over BHI before device can enter an MHI READY
state and proceed with further bootup. Allow this to be handled
by relying on the execution environment check after SYS_ERROR
processing to determine whether to wait for an MHI READY or
download the EDL image over BHI after moving MHI PM state to
Power on Reset internally. This way handling is contained well
within the MHI core driver and helps pave the way for Flash
Programmer execution environment functionality.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617067704-28850-4-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the firmware load handler returns after the EDL image
is downloaded. Wait for an MHI READY transition instead as the
specification expects so as to proceed with further bootup such
as device entering Flash Programmer execution environment.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1617067704-28850-3-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Relying on the current execution environment to determine if EDL
image was downloaded should not be done as the execution
environment can change at this point in error cases and we may
misread it. Instead, MHI can rely on the local 'fw_name' variable
as a safer alternative.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1617067704-28850-2-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
We cannot process a power_down if the power state is DISABLED. There is
no valid mhi_ctxt in that case, so attepting to process the power_down
will likely result in a null pointer dereference. If the power state is
DISABLED, there is nothing to do anyways, so just bail early.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1615409365-8165-1-git-send-email-jhugo@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently ENOMEM is returned when MHI ring is full. This error code is
very misleading. Change to EAGAIN instead.
Signed-off-by: Fan Wu <wufan@codeaurora.org>
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1615408803-7016-1-git-send-email-jhugo@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The variables state and ee are being initialized with values that
are never read and are being updated later with a new values. The
initializations are redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210311111727.8433-1-colin.king@canonical.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The check to see if we have reset the device after detecting syserr at
power_up is inverted. wait_for_event_timeout() returns 0 on failure,
and a positive value on success. The check is looking for non-zero
as a failure, which is likely to incorrectly cause a device init failure
if syserr was detected at power_up. Fix this.
Fixes: e18d4e9fa7 ("bus: mhi: core: Handle syserr during power_up")
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1613165243-23359-1-git-send-email-jhugo@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Update debug prints to include local device in the BHI interrupt
handler. This helps show transitions better between MHI states.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1614208985-20851-5-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In current design, whenever the BHI interrupt is fired, the
execution environment is updated. This can cause race conditions
and impede ongoing power up/down processing. For example, if a
power down is in progress, MHI host updates to a local "disabled"
execution environment. If a BHI interrupt fires later, that value
gets replaced with one from the BHI EE register. This impacts the
controller as it does not expect multiple RDDM execution
environment change status callbacks as an example. Another issue
would be that the device can enter mission mode and the execution
environment is updated, while device creation for SBL channels is
still going on due to slower PM state worker thread run, leading
to multiple attempts at opening the same channel.
Ensure that EE changes are handled only from appropriate places
and occur one after another and handle only PBL modes or RDDM EE
changes as critical events directly from the interrupt handler.
Simplify handling by waiting for SYS ERROR before handling RDDM.
This also makes sure that we use the correct execution environment
to notify the controller driver when the device resets to one of
the PBL execution environments.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1614208985-20851-4-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
During full boot chain firmware download, the PM state worker
downloads the AMSS image after a blocking wait for the SBL
execution environment change when running in PBL transition
itself. Improve this design by having the host download the AMSS
image from the SBL transition of PM state worker thread when a
DEV_ST_TRANSITION_SBL is queued instead of the blocking wait.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1614208985-20851-3-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, client devices are created in SBL or AMSS (mission
mode) and only destroyed after power down or SYS ERROR. When
moving between certain execution environments, such as from SBL
to AMSS, no clean-up is required. This presents an issue where
SBL-specific channels are left open and client drivers now run in
an execution environment where they cannot operate. Fix this by
expanding the mhi_destroy_device() to do an execution environment
specific clean-up if one is requested. Close the gap and destroy
devices in such scenarios that allow SBL client drivers to clean
up once device enters mission mode.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1614208985-20851-2-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Jakub Kicinski