The current discovery state machine the driver treated FLOGI oddly. When
point to point, an FLOGI is to be exchanged by the two ports, with the port
with the most significant WWN then proceeding with PLOGI. The
implementation in the driver was keyed to closely with "what have I sent",
not with what has happened between the two endpoints. Thus, it blatantly
would ACC an FLOGI, but reject PLOGI's until it had its FLOGI ACC'd. The
problem is - the sending of FLOGI may be delayed for some reason, or the
response to FLOGI held off by the other side. In the failing situation the
other side sent an FLOGI, which was ACC'd, then sent PLOGIs which were then
rjt'd until the retry count for the PLOGIs were exceeded and the port gave
up. The FLOGI may have been very late in transmit, or the response held off
until the PLOGIs failed. Given the other port had the higher WWN, no PLOGIs
would occur and communication stopped.
Correct the situation by changing the FLOGI handling. Defer any response to
an FLOGI until the driver has sent its FLOGI as well. Then, upon either
completion of the sent FLOGI, or upon sending an ACC to a received FLOGI
(which may be received before or just after FLOGI was sent). the driver
will act on who has the higher WWN. if the other port does, the driver will
noop any handling of an FLOGI response (if outstanding) and wait for PLOGI.
If the local port does, the driver will transition to sending PLOGI and
will noop any action on responding to an FLOGI (if not yet received).
Fortunately, to implement this, it only took another state flag and
deferring any FLOGI response if the FLOGI has yet to be transmit. All
subsequent actions were already in place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Depending on the chipset, the number of NPIV vports may vary and be in
excess of what most switches support (256). To avoid confusion with the
users, limit the reported NPIV vports to 256.
Additionally correct the 16G adapter which is reporting a bogus NPIV vport
number if the link is down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is hitting null pring pointers in lpfc_do_work().
Pointer assignment occurs based on SLI-revision. If recovering after an
error, its possible the sli revision for the port was cleared, making the
lpfc_phba_elsring() not return a ring pointer, thus the null pointer.
Add SLI revision checking to lpfc_phba_elsring() and status checking to all
callers.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add trunking support to the driver. Trunking is found on more recent
asics. In general, trunking appears as a single "port" to the driver
and overall behavior doesn't differ. Link speed is reported as an
aggregate value, while link speed control is done on a per-physical
link basis with all links in the trunk symmetrical. Some commands
returning port information are updated to additionally provide
trunking information. And new ACQEs are generated to report physical
link events relative to the trunk.
This patch contains the following modifications:
- Added link speed settings of 128GB and 256GB.
- Added handling of trunk-related ACQEs, mainly logging and trapping
of physical link statuses.
- Added additional bsg interface to query trunk state by applications.
- Augment link_state sysfs attribtute to display trunk link status
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switches seem to respond faster to GID_PT vs GID_FT NameServer
queries. Add support for GID_PT to be used over GID_FT to enable
faster storage failover detection. Includes addition of new module
parameter to select between GID_PT and GID_FT (GID_FT is default).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Testing a point-to-point topology and a case of re-FLOGI without
intervening link bouncing, showed an odd interaction with firmware and
a resulting scenario where the driver no longer probed after accepting
the new FLOGI.
Work around the firmware issue by issuing a link bounce if a FLOGI is
received after the link is already up and FLOGI's accepted.
While debugging the issue, realized that some debug traces should be
clarified to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas. In addition there's a set of mostly
small updates to the target subsystem a set of conversions to the
generic DMA API, which do have some potential for issues in the older
drivers but we'll handle those as case by case fixes. A new myrs for
the DAC960/mylex raid controllers to replace the block based DAC960
which is also being removed by Jens in this merge window. Plus the
usual slew of trivial changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW9BQJSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishU3MAP41T8yW
UJQDCprj65pCR+9mOUWzgMvgAW/15ouK89x/7AD/XAEQZqoAgpFUbgnoZWGddZkS
LykIzSiLHP4qeDOh1TQ=
=2JMU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas.
In addition there's a set of mostly small updates to the target
subsystem a set of conversions to the generic DMA API, which do have
some potential for issues in the older drivers but we'll handle those
as case by case fixes.
A new myrs driver for the DAC960/mylex raid controllers to replace the
block based DAC960 which is also being removed by Jens in this merge
window.
Plus the usual slew of trivial changes"
[ "myrs" stands for "MYlex Raid Scsi". Obviously. Silly of me to even
wonder. There's also a "myrb" driver, where the 'b' stands for
'block'. Truly, somebody has got mad naming skillz. - Linus ]
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (237 commits)
scsi: myrs: Fix the processor absent message in processor_show()
scsi: myrs: Fix a logical vs bitwise bug
scsi: hisi_sas: Fix NULL pointer dereference
scsi: myrs: fix build failure on 32 bit
scsi: fnic: replace gross legacy tag hack with blk-mq hack
scsi: mesh: switch to generic DMA API
scsi: ips: switch to generic DMA API
scsi: smartpqi: fully convert to the generic DMA API
scsi: vmw_pscsi: switch to generic DMA API
scsi: snic: switch to generic DMA API
scsi: qla4xxx: fully convert to the generic DMA API
scsi: qla2xxx: fully convert to the generic DMA API
scsi: qla1280: switch to generic DMA API
scsi: qedi: fully convert to the generic DMA API
scsi: qedf: fully convert to the generic DMA API
scsi: pm8001: switch to generic DMA API
scsi: nsp32: switch to generic DMA API
scsi: mvsas: fully convert to the generic DMA API
scsi: mvumi: switch to generic DMA API
scsi: mpt3sas: switch to generic DMA API
...
This patch adds the ability to read firmware logs from the adapter. The driver
registers a buffer with the adapter that is then written to by the adapter.
The adapter posts CQEs to indicate content updates in the buffer. While the
adapter is writing to the buffer in a circular fashion, an application will
poll the driver to read the next amount of log data from the buffer.
Driver log buffer size is configurable via the ras_fwlog_buffsize sysfs
attribute. Verbosity to be used by firmware when logging to host memory is
controlled through the ras_fwlog_level attribute. The ras_fwlog_func
attribute enables or disables loggy by firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When taking the board offline while performing i/o, unsafe locking errors
occurred and irq level isn't properly managed.
In lpfc_sli_hba_down, spin_lock_irqsave(&phba->hbalock, flags) does not
disable softirqs raised from timer expiry. It is possible that a softirq is
raised from the lpfc_els_retry_delay routine and recursively requests the same
phba->hbalock spinlock causing deadlock.
Address the deadlocks by creating a new port_list lock. The softirq behavior
can then be managed a level deeper into the calling sequences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver allocates a sg list per io struture based on a fixed maximum
size. When it registers with the protocol transports and indicates the max sg
list size it supports, the driver manipulates the fixed value to report a
lesser amount so that it has reserved space for sg elements that are used for
DIF.
The driver initialization path sets the cfg_sg_seg_cnt field to the
manipulated value for scsi. NVME initialization ran afterward and capped it's
maximum by the manipulated value for SCSI. This erroneously made NVME report
the SCSI-reduce-for-DIF value that reduced the max io size for nvme and wasted
sg elements.
Rework the driver so that cfg_sg_seg_cnt becomes the overall maximum size and
allow the max size to be tunable. A separate (new) scsi sg count is then
setup with the scsi-modified reduced value. NVME then initializes based off
the overall maximum.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent change added some MDS processing in the lpfc_drain_txq routine
that relies on the fcp_wq being allocated. For nvmet operation the fcp_wq
is not allocated because it can only be an nvme-target. When the original
MDS support was added LS_MDS_LOOPBACK was defined wrong, (0x16) it should
have been 0x10 (decimal value used for hex setting). This incorrect value
allowed MDS_LOOPBACK to be set simultaneously with LS_NPIV_FAB_SUPPORTED,
causing the driver to crash when it accesses the non-existent fcp_wq.
Correct the bad value setting for LS_MDS_LOOPBACK.
Fixes: ae9e28f36a ("lpfc: Add MDS Diagnostic support.")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change references from "Broadcom Limited" to "Broadcom Inc." in the
copyright message. Update copyright duration if not yet updated for 2018.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PBDE optimizations aren't supported in all firmware revs.
Make optimizations configurable in case there's a side effect on old
firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under large io load, the current sizing of asynchronous buffer counts
could be exceeded, indicated by a 2885 log message:
2885 Port Status Event: port status reg 0x81800000, port smphr
reg 0xc000, error 1=0x52004a01, error 2=0x0
Enlarge the async receive queue size. Allow for a configurable number
of buffers to be posted to each RQ, using the new attribute
lpfc_nvmet_mrq_post.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When debugging various issues, per IO channel IO statistics were useful
to understand what was happening. However, many of the stats were on a
port basis rather than an io channel basis.
Move statistics to an io channel basis.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The max_scsicmpl_time parameter can be used to perform scsi cmd queue
depth mgmt based on io completion time: the queue depth is reduced to
make completion time shorter. However, as soon as an io completes and
the completion time is within limits, the code immediately bumps the
queue depth limit back up to the target queue depth. Thus the procedure
restarts, effectively limiting the usefulness of adjusting queue depth
to help completion time.
This patch makes the following changes:
- Removes the code at io completion that resets the queue depth as soon
as within limits.
- As the code removed was where the target queue depth was first
applied, change target queue depth application so that it occurs when
the parameter is changed.
- Makes target queue depth a standard parameter: both a module
parameter and a sysfs parameter.
- Optimizes the command pending count by using atomics rather than
locks.
- Updates the debugfs nodelist stats to allow better debugging of
pending command counts.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hardware offload for NVME commands was created when the
FC-NVME standard was setting SGL Descriptor Type to SGL Data
Block Descriptor (0h) and SGL Descriptor Sub Type to Address (0h).
A late change in NVMe-over-Fabrics obsoleted these values, creating
a transport SGL descriptor type with new values to go into these
fields.
For initial hardware support, in order to be compliant to the spec,
use host-supplied cmd IU buffers instead of the adapter generated
values. Later hardware will correct this.
Add a module parameter to override this offload disablement if looking
for lowest latency. This is reasonable as nothing in FC-NVME uses
the SQE SGL values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current driver isn't taking advantage of a performance hint whereby
the initial data buffer descriptor can be placed in the WQE as well as
the SGL.
Add the logic to detect support for the feature and to use it when
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The G7 adapter supports 64G link speeds. Add support to the driver.
In addition, a small cleanup to replace the odd bitmap logic with
a switch case.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New if_type=6 adapters support an additional BAR that provides
apertures to allow direct WQE to adapter push support - termed
Direct Packet Push (DPP). WQ creation differs slightly to ask for
a WQ to be DPP-ized. When submitting a WQE to a DPP WQ, it is
submitted to the host memory for the WQ normally, but is also
written by the host cpu directly to a BAR aperture. Write buffer
coalescing in hardware is (hopefully) turned on, enabling single
pci write operation support. The doorbell is thing rung to indicate
the WQE is available and was pushed to the aperture.
This patch:
- Updates the WQ Create commands for the DPP options
- Adds the bar mapping for if_type=6 DPP bar
- Adds the WQE pushing to the DDP aperture received from WQ create
- Adds a new module parameter to disable DPP operation if desired.
Default is enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increased CQ and WQ sizes for SCSI FCP, matching those used for NVMe
development.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME targets appear to randomly disconnect from the initiator when
running heavy IO.
The error is due to the host aggregate (across all controllers) io load
was beyond the maximum exchange count for nvme on the adapter. The
driver was properly returning a resource busy status, but the io load
was so great heartbeat commands would be bounced and not have a
successful retry within the fuzz amount for the nvme heartbeat (yes, a
very high io load!). Thus the target was terminating the controller due
to a keep alive failure.
Resolve by reserving a few exchanges (by counters) which can be used
when the adapter is out of normal exchanges and the command is a NVME
heartbeat command. As counters are used, while the reserved command is
outstanding, as soon as any other exchange completes, the counters are
adjusted and the reserved count is replenished. The heartbeat completes
execution in a normal fashion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The logic for sg_seg_cnt is a bit convoluted. This patch tries to clean
up a couple of areas, especially around the +2 and +1 logic.
This patch:
- Cleans up the lpfc_sg_seg_cnt attribute to specify a real minimum
rather than making the minimum be whatever the default is.
- Removes the hardcoding of +2 (for the number of elements we use in a
sgl for cmd iu and rsp iu) and +1 (an additional entry to compensate
for nvme's reduction of io size based on a possible partial page)
logic in sg list initialization. In the case where the +1 logic is
referenced in host and target io checks, use the values set in the
transport template as that value was properly set.
There can certainly be more done in this area and it will be addressed
in combined host/target driver effort.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Raise the maximum NVME sg list size allowed to 256 elements.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
XRI_ABORTED_CQE completions were not being handled in the fast path.
They were being queued and deferred to the lpfc worker thread for
processing. This is an artifact of the driver design prior to moving
queue processing out of the isr and into a workq element. Now that queue
processing is already in a deferred context, remove this artifact and
process them directly.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under heavy target nvme load duration, the lpfc irq handler is
encountering cpu lockup warnings.
Convert the driver to a shortened ISR handler which identifies the
interrupting condition then schedules a workq thread to process the
completion queue the interrupt was for. This moves all the real work
into the workq element.
As nvmet_fc upcalls are no longer in ISR context, don't set the feature
flags
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add Buffer to buffer credit recovery support to the driver. This is a
negotiated feature with the peer that allows for both sides to detect
dropped RRDY's and FC Frames and recover credit.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API. It also updates
some comments, accordingly.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Administrator intervention is currently required to get good numbers
when switching from running latency tests to IOPS tests.
The configured interrupt coalescing values will greatly effect the
results of these tests. Currently, the driver has a single coalescing
value set by values of the module attribute. This patch changes the
driver to support auto-configuration of the coalescing value based on
the total number of outstanding IOs and average number of CQEs processed
per interrupt for an EQ. Values are checked every 5 seconds.
The driver defaults to the automatic selection. Automatic selection can
be disabled by the new lpfc_auto_imax module_parameter.
Older hardware can only change interrupt coalescing by mailbox
command. Newer hardware supports change via a register. The patch
support both.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME FC counters don't reflect actual results
Since counters are not atomic, or protected by a lock, the values often
get screwed up.
Make them atomic, like NVMET. Fix up sysfs and debugfs display
accordingly Added Outstanding IOs to stats display
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added code to support Cisco MDS loopback diagnostic. The diagnostics run
various loopbacks including one which loops-back frame through the
driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Previous logic would just drop the IO.
Added logic to queue the IO to wait for an IO context resource from an
IO thats already in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently IO resources are mapped 1 to 1 with RQ buffers posted
Added logic to separate RQE buffers from IO op resources
(sgl/iocbq/context). During initialization, the driver will determine
how many SGLs it will allocate for NVMET (based on what the firmware
reports) and associate a NVMET IOCBq and NVMET context structure with
each one.
Now that hdr/data buffers are immediately reposted back to the RQ, 512
RQEs for each MRQ is sufficient. Also, since NVMET data buffers are now
128 bytes, lpfc_nvmet_mrq_post is not necessary anymore as we will
always post the max (512) buffers per NVMET MRQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using 2048 byte buffer and onle 128 bytes is needed.
Create nee LFPC_NVMET_DATA_BUF_SIZE define to use for NVMET RQ/MRQs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver panic when using the els_wq during port reset.
Check for NULL els_wq before dereferencing.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding support for Fabric assigned WWPN and WWNN.
Firmware sends first FLOGI to fabric with vendor version changes.
On link up driver gets updated service parameter with FAWWN assigned port
name. Driver sends 2nd FLOGI with updated fawwpn and modifies the
vport->fc_portname in driver.
Note:
Soft wwpn will not be allowed when fawwpn is enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cannot set NVME segment counts to a large number
The existing module parameter lpfc_sg_seg_cnt is used for both
SCSI and NVME.
Limit the module parameter lpfc_sg_seg_cnt to 128 with the
default being 64 for both NVME and NVMET, assuming NVME is enabled in the
driver for that port. The driver will set max_sgl_segments in the
NVME/NVMET template to lpfc_sg_seg_cnt + 1.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
This patch addresses the smatch issues identified by Dan Carpenter
in http://www.spinics.net/lists/linux-scsi/msg105663.html
The issues are:
drivers/scsi/lpfc/lpfc_hbadisc.c:316 lpfc_dev_loss_tmo_handler()
warn: we tested 'vport->load_flag & 2' before and it was 'false'
Action: removed item from test
drivers/scsi/lpfc/lpfc_hbadisc.c:701 lpfc_work_done()
warn: test_bit() takes a bit number
Action: changed definition so bit number
drivers/scsi/lpfc/lpfc_hbadisc.c:2206 lpfc_mbx_cmpl_fcf_scan_read_fcf_rec()
error: uninitialized symbol 'vlan_id'.
drivers/scsi/lpfc/lpfc_hbadisc.c:2582 lpfc_mbx_cmpl_fcf_rr_read_fcf_rec()
error: uninitialized symbol 'vlan_id'.
drivers/scsi/lpfc/lpfc_hbadisc.c:2683 lpfc_mbx_cmpl_read_fcf_rec() error:
uninitialized symbol 'vlan_id'.
Action: initilized value
drivers/scsi/lpfc/lpfc_hbadisc.c:4025 lpfc_register_remote_port()
error: we previously assumed 'rdata' could be null (see line 4023)
Action: refactored check block
drivers/scsi/lpfc/lpfc_hbadisc.c:4613 lpfc_sli4_dequeue_nport_iocbs()
error: double unlock 'irq:'
Action: removed inner irq reference
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A previous change unilaterally removed the hba reset entry point
from the sli3 host template. This was done to allow tape devices
being used for back up from being removed. Why was this done ?
When there was non-responding device on the fabric, the error
escalation policy would escalate to the reset handler. When the
reset handler was called, it would reset the adapter, dropping
link, thus logging out and terminating all i/o's - on any target.
If there was a tape device on the same adapter that wasn't in
error, it would kill the tape i/o's, effectively killing the
tape device state. With the reset point removed, the adapter
reset avoided the fabric logout, allowing the other devices to
continue to operate unaffected. A hack - yes. Hint: we really
need a transport I_T nexus reset callback added to the eh process
(in between the SCSI target reset and hba reset points), so a
fc logout could occur to the one bad target only and stop the error
escalation process.
This patch commonizes the approach so it can be used for sli3 and sli4
adapters, but mandates the admin, via module parameter, specifically
identify which adapters the resets are to be removed for. Additionally,
bus_reset, which sends Target Reset TMFs to all targets, is also removed
from the template as it too has the same effect as the adapter reset.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
previous code did little more than log a message.
This patch adds abort path support, modeled after the SCSI code paths.
Currently addresses only the initiator path. Target path under
development, but stubbed out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyrights to 2017 for all files touched in this patch set
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Target: Receive buffer updates
Allocates buffer pools and configures adapter interfaces to handle
receive buffer (asynchronous FCP CMD ius, first burst data)
from the adapter. Splits by protocol, etc.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Target: Base modifications
This set of patches adds the base modifications for NVME target support
The base modifications consist of:
- Additional module parameters or configuration tuning
- Enablement of configuration mode for NVME target. Ties into the
queueing model put into place by the initiator basemods patches.
- Target-specific buffer pools, dma pools, sgl pools
[mkp: fixed space at end of file]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Add debugfs support
Adds debugfs snippets to cover the new NVME initiator functionality
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Tie in to NVME Fabrics nvme_fc LLDD initiator api
Adds the routines to:
- register and deregister the FC port as a nvme-fc initiator localport
- register and deregister remote FC ports as a nvme-fc remoteport
- binding of nvme queues to adapter WQs
- send/perform NVME LS's
- send/perform NVME FCP initiator io operations
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Merge into FC discovery
Adds NVME PRLI support and Nameserver registrations and Queries for NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Base modifications
This patch adds base modifications for NVME initiator support.
The base modifications consist of:
- Formal split of SLI3 rings from SLI-4 WQs (sometimes referred to as
rings as well) as implementation now widely varies between the two.
- Addition of configuration modes:
SCSI initiator only; NVME initiator only; NVME target only; and
SCSI and NVME initiator.
The configuration mode drives overall adapter configuration,
offloads enabled, and resource splits.
NVME support is only available on SLI-4 devices and newer fw.
- Implements the following based on configuration mode:
- Exchange resources are split by protocol; Obviously, if only
1 mode, then no split occurs. Default is 50/50. module attribute
allows tuning.
- Pools and config parameters are separated per-protocol
- Each protocol has it's own set of queues, but share interrupt
vectors.
SCSI:
SLI3 devices have few queues and the original style of queue
allocation remains.
SLI4 devices piggy back on an "io-channel" concept that
eventually needs to merge with scsi-mq/blk-mq support (it is
underway). For now, the paradigm continues as it existed
prior. io channel allocates N msix and N WQs (N=4 default)
and either round robins or uses cpu # modulo N for scheduling.
A bunch of module parameters allow the configuration to be
tuned.
NVME (initiator):
Allocates an msix per cpu (or whatever pci_alloc_irq_vectors
gets)
Allocates a WQ per cpu, and maps the WQs to msix on a WQ #
modulo msix vector count basis.
Module parameters exist to cap/control the config if desired.
- Each protocol has its own buffer and dma pools.
I apologize for the size of the patch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
----
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create common wq, cq, eq, rq print functions
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This avoids having to store the msix_entries array and simpliefies the
shutdown and cleanup path a lot.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart