Commit Graph

1808 Commits

Author SHA1 Message Date
Linus Torvalds fed678dc8a Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block:
  floppy: use del_timer_sync() in init cleanup
  blk-cgroup: be able to remove the record of unplugged device
  block: Don't check QUEUE_FLAG_SAME_COMP in __blk_complete_request
  mm: Add comment explaining task state setting in bdi_forker_thread()
  mm: Cleanup clearing of BDI_pending bit in bdi_forker_thread()
  block: simplify force plug flush code a little bit
  block: change force plug flush call order
  block: Fix queue_flag update when rq_affinity goes from 2 to 1
  block: separate priority boosting from REQ_META
  block: remove READ_META and WRITE_META
  xen-blkback: fixed indentation and comments
  xen-blkback: Don't disconnect backend until state switched to XenbusStateClosed.
2011-09-21 13:20:21 -07:00
Girish K S 49bb1e6195 mmc: sdhci-s3c: Fix mmc card I/O problem
This patch fixes the problem in sdhci-s3c host driver for Samsung Soc's.
During the card identification stage the mmc core driver enumerates for
the best bus width in combination with the highest available data rate.
It starts enumerating from the highest bus width (8) to lowest width (1).

In case of few MMC cards the 4-bit bus enumeration fails and tries
the 1-bit bus enumeration. When switched to 1-bit bus mode the host driver
has to clear the previous bus width setting and apply the new setting.

The current patch will clear the previous bus mode and apply the new
mode setting.

Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-31 16:25:52 -04:00
Subhash Jadavani 93c712f99d mmc: sd: UHS-I bus speed should be set last in UHS initialization
mmc_sd_init_uhs_card function sets the driver type, current limit
and bus speed mode on card as well as on host controller side.

Currently bus speed mode is set by sending CMD6 to card and
immediately setting the timing mode in host controller. But
then before initiating tuning sequence, it also tries to set
current limit by sending CMD6 to card which results in data
timeout errors in controller if bus speed mode is SDR50/SDR104 mode.

So basically bus speed mode should be set only after current limit
is set in the card and immediately after setting the bus speed mode,
tuning sequence should be initiated.

Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-31 16:25:52 -04:00
Simon Horman b91df1593e mmc: sdhi: initialise mmc_data->flags before use
This corrects a logic error that I introduced in
"mmc: sdhi: Add write16_hook"

Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-31 16:25:51 -04:00
Mika Westerberg 50a50f9248 mmc: core: use non-reentrant workqueue for clock gating
The default multithread workqueue can cause the same work to be executed
concurrently on a different CPUs. This isn't really suitable for clock
gating as it might already gated the clock and gating it twice results both
host->clk_old and host->ios.clock to be set to 0.

To prevent this from happening we use system_nrt_wq instead.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-31 16:25:50 -04:00
Mika Westerberg 778e277cb8 mmc: core: prevent aggressive clock gating racing with ios updates
We have seen at least two different races when clock gating kicks in in a
middle of ios structure update.

First one happens when ios->clock is changed outside of aggressive clock
gating framework, for example via mmc_set_clock(). The race might happen
when we run following code:

mmc_set_ios():
	...
	if (ios->clock > 0)
		mmc_set_ungated(host);

Now if gating kicks in right after the condition check we end up setting
host->clk_gated to false even though we have just gated the clock. Next
time a request is started we try to ungate and restore the clock in
mmc_host_clk_hold(). However since we have host->clk_gated set to false the
original clock is not restored.

This eventually will cause the host controller to hang since its clock is
disabled while we are trying to issue a request. For example on Intel
Medfield platform we see:

[   13.818610] mmc2: Timeout waiting for hardware interrupt.
[   13.818698] sdhci: =========== REGISTER DUMP (mmc2)===========
[   13.818753] sdhci: Sys addr: 0x00000000 | Version:  0x00008901
[   13.818804] sdhci: Blk size: 0x00000000 | Blk cnt:  0x00000000
[   13.818853] sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[   13.818903] sdhci: Present:  0x1fff0000 | Host ctl: 0x00000001
[   13.818951] sdhci: Power:    0x0000000d | Blk gap:  0x00000000
[   13.819000] sdhci: Wake-up:  0x00000000 | Clock:    0x00000000
[   13.819049] sdhci: Timeout:  0x00000000 | Int stat: 0x00000000
[   13.819098] sdhci: Int enab: 0x00ff00c3 | Sig enab: 0x00ff00c3
[   13.819147] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[   13.819196] sdhci: Caps:     0x6bee32b2 | Caps_1:   0x00000000
[   13.819245] sdhci: Cmd:      0x00000000 | Max curr: 0x00000000
[   13.819292] sdhci: Host ctl2: 0x00000000
[   13.819331] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
[   13.819377] sdhci: ===========================================
[   13.919605] mmc2: Reset 0x2 never completed.

and it never recovers.

Second race might happen while running mmc_power_off():

static void mmc_power_off(struct mmc_host *host)
{
	host->ios.clock = 0;
	host->ios.vdd = 0;

[ clock gating kicks in here ]

	/*
	 * Reset ocr mask to be the highest possible voltage supported for
	 * this mmc host. This value will be used at next power up.
	 */
	host->ocr = 1 << (fls(host->ocr_avail) - 1);

	if (!mmc_host_is_spi(host)) {
		host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
		host->ios.chip_select = MMC_CS_DONTCARE;
	}
	host->ios.power_mode = MMC_POWER_OFF;
	host->ios.bus_width = MMC_BUS_WIDTH_1;
	host->ios.timing = MMC_TIMING_LEGACY;
	mmc_set_ios(host);
}

If the clock gating worker kicks in while we are only partially updated the
ios structure the host controller gets incomplete ios and might not work as
supposed. Again on Intel Medfield platform we get:

[    4.185349] kernel BUG at drivers/mmc/host/sdhci.c:1155!
[    4.185422] invalid opcode: 0000 [#1] PREEMPT SMP
[    4.185509] Modules linked in:
[    4.185565]
[    4.185608] Pid: 4, comm: kworker/0:0 Not tainted 3.0.0+ #240 Intel Corporation Medfield/iCDKA
[    4.185742] EIP: 0060:[<c136364e>] EFLAGS: 00010083 CPU: 0
[    4.185827] EIP is at sdhci_set_power+0x3e/0xd0
[    4.185891] EAX: f5ff98e0 EBX: f5ff98e0 ECX: 00000000 EDX: 00000001
[    4.185970] ESI: f5ff977c EDI: f5ff9904 EBP: f644fe98 ESP: f644fe94
[    4.186049]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[    4.186125] Process kworker/0:0 (pid: 4, ti=f644e000 task=f644c0e0 task.ti=f644e000)
[    4.186219] Stack:
[    4.186257]  f5ff98e0 f644feb0 c1365173 00000282 f5ff9460 f5ff96e0 f5ff96e0 f644feec
[    4.186418]  c1355bd8 f644c0e0 c1499c3d f5ff96e0 f644fed4 00000006 f5ff96e0 00000286
[    4.186579]  f644fedc c107922b f644feec 00000286 f5ff9460 f5ff9700 f644ff10 c135839e
[    4.186739] Call Trace:
[    4.186802]  [<c1365173>] sdhci_set_ios+0x1c3/0x340
[    4.186883]  [<c1355bd8>] mmc_gate_clock+0x68/0x120
[    4.186963]  [<c1499c3d>] ? _raw_spin_unlock_irqrestore+0x4d/0x60
[    4.187052]  [<c107922b>] ? trace_hardirqs_on+0xb/0x10
[    4.187134]  [<c135839e>] mmc_host_clk_gate_delayed+0xbe/0x130
[    4.187219]  [<c105ec09>] ? process_one_work+0xf9/0x5b0
[    4.187300]  [<c135841d>] mmc_host_clk_gate_work+0xd/0x10
[    4.187379]  [<c105ec82>] process_one_work+0x172/0x5b0
[    4.187457]  [<c105ec09>] ? process_one_work+0xf9/0x5b0
[    4.187538]  [<c1358410>] ? mmc_host_clk_gate_delayed+0x130/0x130
[    4.187625]  [<c105f3c8>] worker_thread+0x118/0x330
[    4.187700]  [<c1496cee>] ? preempt_schedule+0x2e/0x50
[    4.187779]  [<c105f2b0>] ? rescuer_thread+0x1f0/0x1f0
[    4.187857]  [<c1062cf4>] kthread+0x74/0x80
[    4.187931]  [<c1062c80>] ? __init_kthread_worker+0x60/0x60
[    4.188015]  [<c149acfa>] kernel_thread_helper+0x6/0xd
[    4.188079] Code: 81 fa 00 00 04 00 0f 84 a7 00 00 00 7f 21 81 fa 80 00 00 00 0f 84 92 00 00 00 81 fa 00 00 0
[    4.188780] EIP: [<c136364e>] sdhci_set_power+0x3e/0xd0 SS:ESP 0068:f644fe94
[    4.188898] ---[ end trace a7b23eecc71777e4 ]---

This BUG() comes from the fact that ios.power_mode was still in previous
value (MMC_POWER_ON) and ios.vdd was set to zero.

We prevent these by inhibiting the clock gating while we update the ios
structure.

Both problems can be reproduced by simply running the device in a reboot
loop.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-31 16:25:49 -04:00
Mika Westerberg 08c14071fd mmc: rename mmc_host_clk_{ungate|gate} to mmc_host_clk_{hold|release}
As per suggestion by Linus Walleij:

  > If you think the names of the functions are confusing then
  > you may rename them, say like this:
  >
  > mmc_host_clk_ungate() -> mmc_host_clk_hold()
  > mmc_host_clk_gate() -> mmc_host_clk_release()
  >
  > Which would make the usecases more clear

(This is CC'd to stable@ because the next two patches, which fix
observable races, depend on it.)

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-31 16:24:54 -04:00
Shawn Guo 66506f7617 mmc: sdhci-esdhc-imx: add missing inclusion of linux/module.h
There are the following warnings and errorx when compiling the driver.
The patch adds the missing inclusion of linux/module.h to fix them.

drivers/mmc/host/sdhci-esdhc-imx.c:563:12: error: ‘THIS_MODULE’ undeclared here (not in a function)
[..]

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-28 14:10:00 -04:00
Christoph Hellwig 65299a3b78 block: separate priority boosting from REQ_META
Add a new REQ_PRIO to let requests preempt others in the cfq I/O schedule,
and lave REQ_META purely for marking requests as metadata in blktrace.

All existing callers of REQ_META except for XFS are updated to also
set REQ_PRIO for now.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2011-08-23 14:50:29 +02:00
Seungwon Jeon 6daa777866 mmc: dw_mmc: Fix DDR mode support.
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:32 -04:00
Jaehoon Chung 7435bb7950 mmc: core: use defined R1_STATE_PRG macro for card status
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:31 -04:00
Andy Shevchenko 65be3fef93 mmc: sdhci: use f_max instead of host->clock for timeouts
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:30 -04:00
Andy Shevchenko 272308caaa mmc: sdhci: move timeout_clk calculation farther down
This moves the calculation below the assignment of mmc->f_max, which
we need for calculating timeout_clk in the next patch in this series.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:29 -04:00
Andy Shevchenko 78a2ca2727 mmc: sdhci: check host->clock before using it as a denominator
Sometimes host->clock could be zero which is a legal situation. This
patch checks host->clock before usage as a denominator when timeout is
calculated. A similar patch is applied for mmc core (see commit e9b8684,
"mmc: fix division by zero in MMC core").

Without this patch, the execution of the sdhci_calc_timeout could end up
with a backtrace:

<0>[    4.014319] divide error: 0000 [#1] PREEMPT SMP
<4>[    4.014352] Modules linked in: g_ether
<4>[    4.014376]
<4>[    4.014393] Pid: 33, comm: kworker/u:2 Not tainted 3.0.0+ #646
<4>[    4.014421] EIP: 0060:[<c12fa38e>] EFLAGS: 00010046 CPU: 1
<4>[    4.014449] EIP is at sdhci_calc_timeout+0x2e/0x100
<4>[    4.014468] EAX: 00000000 EBX: f5930fc8 ECX: 00000000 EDX: 00000000
<4>[    4.014488] ESI: f5291de8 EDI: f5291db8 EBP: f5291c6c ESP: f5291c50
<4>[    4.014508]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
<0>[    4.014529] Process kworker/u:2 (pid: 33, ti=f5290000 task=f53065a0 task.ti=f5290000)
<0>[    4.014546] Stack:
<4>[    4.014557]  00000082 c1054fdd f5291c78 04000000 f5930fc8 f5291de8 f5291db8 f5291cac
<4>[    4.014611]  c12fab7c c107a98b f5291c88 c13b6d3f f593109c f5882000 f5291cac c1054fdd
<4>[    4.014663]  00000000 00000000 f5882000 00000082 f5930fc8 f5291db8 0000000a f5291ccc
<0>[    4.014716] Call Trace:
<4>[    4.014743]  [<c1054fdd>] ? mod_timer+0x11d/0x380
<4>[    4.014770]  [<c12fab7c>] sdhci_prepare_data+0x2c/0x3a0
<4>[    4.014798]  [<c107a98b>] ? trace_hardirqs_off+0xb/0x10
<4>[    4.014827]  [<c13b6d3f>] ? _raw_spin_unlock_irqrestore+0x2f/0x60
<4>[    4.014854]  [<c1054fdd>] ? mod_timer+0x11d/0x380
<4>[    4.014880]  [<c12fc7db>] sdhci_send_command+0xdb/0x210
<4>[    4.014906]  [<c12fd5f3>] sdhci_request+0xc3/0x150
<4>[    4.014932]  [<c12ec56a>] mmc_start_request+0xda/0x200
<4>[    4.014960]  [<c120d7c2>] ? __raw_spin_lock_init+0x32/0x60
<4>[    4.014989]  [<c1066a85>] ? __init_waitqueue_head+0x35/0x50
<4>[    4.015015]  [<c12ec70b>] mmc_wait_for_req+0x7b/0x90
<4>[    4.015045]  [<c12f0c67>] mmc_send_cxd_data+0xf7/0x130
<4>[    4.015076]  [<c12ecbc0>] ? mmc_erase+0x140/0x140
<4>[    4.015102]  [<c12f139d>] mmc_send_ext_csd+0x1d/0x20
<4>[    4.015125]  [<c12efef0>] mmc_get_ext_csd+0x70/0x140
<4>[    4.015151]  [<c12effe8>] mmc_compare_ext_csds+0x28/0x190
<4>[    4.015176]  [<c12f039f>] mmc_init_card+0x24f/0x650
<4>[    4.015201]  [<c13b6d5d>] ? _raw_spin_unlock_irqrestore+0x4d/0x60
<4>[    4.015226]  [<c107fd9c>] ? trace_hardirqs_on_caller+0x11c/0x160
<4>[    4.015255]  [<c12f09a4>] mmc_attach_mmc+0xa4/0x190
<4>[    4.015282]  [<c12ee3f0>] mmc_rescan+0x210/0x240
<4>[    4.015311]  [<c105f9b6>] process_one_work+0x176/0x550
<4>[    4.015336]  [<c105f93a>] ? process_one_work+0xfa/0x550
<4>[    4.015360]  [<c12ee1e0>] ? mmc_init_erase+0x140/0x140
<4>[    4.015385]  [<c1061c2a>] worker_thread+0x12a/0x2c0
<4>[    4.015410]  [<c1061b00>] ? manage_workers.clone.18+0x100/0x100
<4>[    4.015437]  [<c1066244>] kthread+0x74/0x80
<4>[    4.015463]  [<c10661d0>] ? __init_kthread_worker+0x60/0x60
<4>[    4.015490]  [<c13b7dfa>] kernel_thread_helper+0x6/0xd
<0>[    4.015507] Code: 57 89 d7 56 53 89 c3 83 ec 10 8b 40 04 8b 72 28 f6 c4 10 89 45 f0 0f 85 91 00 00 00 85 f6 0f 84 c1 00 00 00 8b 4e 04 31 d2 89 c8 <f7> 73 58 ba d3 4d 62 10 89 c1 8b 06 f7 e2 c1 ea 06 01 d1 f7 45
<0>[    4.015829] EIP: [<c12fa38e>] sdhci_calc_timeout+0x2e/0x100 SS:ESP 0068:f5291c50

Reported-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:28 -04:00
Andy Shevchenko 83cbcd93a1 mmc: Revert "mmc: sdhci: Fix SDHCI_QUIRK_TIMEOUT_USES_SDCLK"
This reverts commit 4b01681c77, which introduced a new potential
divide by zero in the process of fixing one.  The subsequent commits
attempt to fix the issue properly.

Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:27 -04:00
Axel Lin 4906baf080 mmc: tmio: eliminate unused variable 'mmc' warning
Fix below compile warning:
  CC      drivers/mmc/host/tmio_mmc.o
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_suspend':
drivers/mmc/host/tmio_mmc.c:30: warning: unused variable 'mmc'
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_resume':
drivers/mmc/host/tmio_mmc.c:45: warning: unused variable 'mmc'

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:27 -04:00
Tony Lin 0d58864bf3 mmc: esdhc-imx: fix card interrupt loss on freescale eSDHC
Apply a workaround for the imx eSDHC controller to avoid missing
card interrupts.  This makes SDIO work.

Signed-off-by: Tony Lin <tony.lin@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:26 -04:00
Mark Brown 55156d240a mmc: sdhci-s3c: Fix build for header change
A header change has removed an implicit inclusion of module.h, breaking
the build due to the use of THIS_MODULE. Fix that.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:25 -04:00
Shashidhar Hiremath 9b7bbe1085 mmc: dw_mmc: Fix mask in IDMAC_SET_BUFFER1_SIZE macro
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits.  Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.

Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:24 -04:00
Kyungmin Park 38ca285044 mmc: core: Detect eMMC v4.5 ext_csd entries
The eMMC v4.5 Spec is released now:

EXT_CSD_REV	Extended CSD Revision
255-7		Reserved
6		Revision 1.6 (for MMC v4.5)
5		Revision 1.5 (for MMV v4.41)
...

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:22 -04:00
Andy Shevchenko d5a5bd1c3f mmc: mmc_test: avoid stalled file in debugfs
During card removal and inserting cycle the test file in the debugfs could be
stalled until the host driver removes it. Let's keep the file in the linked
list and destroy it when card is removed.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:22 -04:00
Jaehoon Chung 7199e2b61d mmc: sdhci-s3c: add BROKEN_ADMA_ZEROLEN_DESC quirk
Samsung SoCs need to set BROKEN_ADMA_ZEROLEN_DESC.
(If ADMA operation is more than 65535, maybe set by zero.)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:21 -04:00
Philip Rakity 606a15e475 mmc: sdhci: pxav3: controller needs 32 bit ADMA addressing
Enable the quirk.

(Best used in conjunction with patch downgrading ADMA to SDMA when
transfer is not aligned.)

Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:20 -04:00
Aaron Lu 78869618a8 mmc: sdhci: fix retuning timer wrongly deleted in sdhci_tasklet_finish
Currently, the retuning timer for retuning mode 1 will be deleted in
function sdhci_tasklet_finish after a mmc request done, which will make
retuning timing never trigger again. This patch fixed this problem.

Signed-off-by: Aaron Lu <Aaron.Lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:19 -04:00
Shawn Guo abfafc2d10 mmc: sdhci-esdhc-imx: add device tree probe support
The patch adds device tree probe support for sdhci-esdhc-imx driver.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27 09:31:39 +08:00
Shawn Guo a4d2177f00 mmc: sdhci-pltfm: dt device does not pass parent to sdhci_alloc_host
Neither platform based nor dt based device needs to pass the parent
to sdhci_alloc_host.  There is no difference between platform and dt
on this point.

The patch makes the change to pass device itself than its parent to
sdhci_alloc_host for dt case too.  Otherwise the probe function of
sdhci based drivers which is shared between platform and dt will
fail on dt case.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27 09:31:33 +08:00
Shawn Guo 57ed3314e0 mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()
The patch removes all the uses of cpu_is_mx().  Instead, it utilizes
platform_device_id to distinguish the esdhc differences among SoCs.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27 09:31:27 +08:00
Shawn Guo 842afc02cf mmc: sdhci-esdhc-imx: do not reference platform data after probe
The patch copies platform data into pltfm_imx_data and reference
the data there than platform data after probe.

This work is inspired by Grant Likely and Troy Kisky.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27 09:31:21 +08:00
Shawn Guo 913413c307 mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5
The patch extends card_detect and write_protect support to get mx5
family and more scenarios supported.  The changes include:

 * Turn platform_data from optional to mandatory
 * Add cd_types and wp_types into platform_data to cover more use
   cases
 * Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD
 * Adjust some machine codes to adopt the platform_data changes
 * Work around the issue that software reset will get card detection
   circuit stop working

With this patch, card_detect and write_protect gets supported on
mx5 based platforms.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27 09:31:14 +08:00
Rafael J. Wysocki 6c0cbef666 MMC / TMIO: Fix build issue related to struct scatterlist
Fix build issue caused by undefined struct scatterlist in
drivers/mmc/host/tmio_mmc.c.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-26 11:52:55 -07:00
Linus Torvalds 45b583b10a Merge 'akpm' patch series
* Merge akpm patch series: (122 commits)
  drivers/connector/cn_proc.c: remove unused local
  Documentation/SubmitChecklist: add RCU debug config options
  reiserfs: use hweight_long()
  reiserfs: use proper little-endian bitops
  pnpacpi: register disabled resources
  drivers/rtc/rtc-tegra.c: properly initialize spinlock
  drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
  drivers/rtc: add support for Qualcomm PMIC8xxx RTC
  drivers/rtc/rtc-s3c.c: support clock gating
  drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
  init: skip calibration delay if previously done
  misc/eeprom: add eeprom access driver for digsy_mtc board
  misc/eeprom: add driver for microwire 93xx46 EEPROMs
  checkpatch.pl: update $logFunctions
  checkpatch: make utf-8 test --strict
  checkpatch.pl: add ability to ignore various messages
  checkpatch: add a "prefer __aligned" check
  checkpatch: validate signature styles and To: and Cc: lines
  checkpatch: add __rcu as a sparse modifier
  checkpatch: suggest using min_t or max_t
  ...

Did this as a merge because of (trivial) conflicts in
 - Documentation/feature-removal-schedule.txt
 - arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
2011-07-25 21:00:19 -07:00
Amerigo Wang 35eb6db11e notifiers: pm: move pm notifiers into suspend.h
It is not necessary to share the same notifier.h.

Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-25 20:57:15 -07:00
Linus Torvalds d3ec4844d4 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
  fs: Merge split strings
  treewide: fix potentially dangerous trailing ';' in #defined values/expressions
  uwb: Fix misspelling of neighbourhood in comment
  net, netfilter: Remove redundant goto in ebt_ulog_packet
  trivial: don't touch files that are removed in the staging tree
  lib/vsprintf: replace link to Draft by final RFC number
  doc: Kconfig: `to be' -> `be'
  doc: Kconfig: Typo: square -> squared
  doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
  drivers/net: static should be at beginning of declaration
  drivers/media: static should be at beginning of declaration
  drivers/i2c: static should be at beginning of declaration
  XTENSA: static should be at beginning of declaration
  SH: static should be at beginning of declaration
  MIPS: static should be at beginning of declaration
  ARM: static should be at beginning of declaration
  rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
  Update my e-mail address
  PCIe ASPM: forcedly -> forcibly
  gma500: push through device driver tree
  ...

Fix up trivial conflicts:
 - arch/arm/mach-ep93xx/dma-m2p.c (deleted)
 - drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
 - drivers/net/r8169.c (just context changes)
2011-07-25 13:56:39 -07:00
Linus Torvalds dd58ecba48 Merge branch 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
  ARM: msm: platsmp: determine number of CPU cores at boot time
  ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
  ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
  ARM: orion5x: fixup 5181 MPP mask check
  ARM: mxs-dma: include <linux/dmaengine.h>
  ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
  ARM: i.MX53: UARTn_CTS pin should not change RTS input select
  ARM: i.MX53: UARTn_TXD pin should not change RXD input select
  ARM: mx25: Fix typo on CAN1_RX pad setting
  iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
  ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
  ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
  ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
  ARM: i.MX53: Fix IOMUX type o's
  ARM i.MX dma: Fix burstsize settings
  mach-mx5: fix the I2C clock parents
  ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
  ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
  ARM: mx53: Fix some interrupts marked as reserved.
  MXC: iomux-v3: correct NO_PAD_CTRL definition
  ...

Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
2011-07-25 11:53:35 -07:00
Linus Torvalds b6844e8f64 Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
  ARM: 7004/1: fix traps.h compile warnings
  ARM: 6998/2: kernel: use proper memory barriers for bitops
  ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
  ARM: Fix build errors caused by adding generic macros
  ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
  ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
  ARM: GIC: avoid routing interrupts to offline CPUs
  ARM: CPU hotplug: fix abuse of irqdesc->node
  ARM: 6981/2: mmci: adjust calculation of f_min
  ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
  ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
  ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
  ARM: ARM_DMA_ZONE_SIZE is no more
  ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ...
2011-07-24 10:20:54 -07:00
Russell King 06f365acef Merge branches 'btc', 'dma', 'entry', 'fixes', 'linker-layout', 'misc', 'mmci', 'suspend' and 'vfp' into for-next 2011-07-22 23:08:48 +01:00
Linus Torvalds 951cc93a74 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1287 commits)
  icmp: Fix regression in nexthop resolution during replies.
  net: Fix ppc64 BPF JIT dependencies.
  acenic: include NET_SKB_PAD headroom to incoming skbs
  ixgbe: convert to ndo_fix_features
  ixgbe: only enable WoL for magic packet by default
  ixgbe: remove ifdef check for non-existent define
  ixgbe: Pass staterr instead of re-reading status and error bits from descriptor
  ixgbe: Move interrupt related values out of ring and into q_vector
  ixgbe: add structure for containing RX/TX rings to q_vector
  ixgbe: inline the ixgbe_maybe_stop_tx function
  ixgbe: Update ATR to use recorded TX queues instead of CPU for routing
  igb: Fix for DH89xxCC near end loopback test
  e1000: always call e1000_check_for_link() on e1000_ce4100 MACs.
  netxen: add fw version compatibility check
  be2net: request native mode each time the card is reset
  ipv4: Constrain UFO fragment sizes to multiples of 8 bytes
  virtio_net: Fix panic in virtnet_remove
  ipv6: make fragment identifications less predictable
  ipv6: unshare inetpeers
  can: make function can_get_bittiming static
  ...
2011-07-22 14:43:13 -07:00
Daniel Drake bb9cab941c mmc: print debug messages for runtime PM actions
At http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg08371.html
(thread: "mmc: sdio: reset card during power_restore") we found and
fixed a bug where mmc's runtime power management functions were not being
called. We have now also made improvements to the SDIO powerup routine
which could possibly mask this kind of issue in future.

Add debug messages to the runtime PM hooks so that it is easy to verify
if and when runtime PM is happening.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:09 -04:00
Ohad Ben-Cohen ecc024419a mmc: fix runtime PM with -ENOSYS suspend case
In the case where a driver returns -ENOSYS from its suspend handler
to indicate that the device should be powered down over suspend, the
remove routine of the driver was not being called, leading to lots of
confusion during resume.

The problem is that runtime PM is disabled during this process,
and when we reach mmc_sdio_remove, calling the runtime PM functions here
(validly) return errors, and this was causing us to skip the remove
function.

Fix this by ignoring the error value of pm_runtime_get_sync(), which
can return valid errors. This also matches the behaviour of
pci_device_remove().

Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:09 -04:00
Jean-Christophe PLAGNIOL-VILLARD b0a68ec944 mmc: at91_mci: move register header from include/ to drivers/
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:08 -04:00
Koen Beel d982dcdc4e mmc: mxs-mmc: fix clock rate setting
Fix clock rate setting in the mxs-mmc driver. Previously, if div2 was 0
then the value for TIMING_CLOCK_RATE would have been 255 instead of 0.
The limits for div1 (TIMING_CLOCK_DIVIDE) and div2 (TIMING_CLOCK_RATE+1)
were also not correctly defined.

Can easily be reproduced on mx23evk: default clock for high speed sdio
cards is 50 MHz. With a SSP_CLK of 28.8 MHz default), this resulted in
an actual clock rate of about 56 kHz.  Tested on mx23evk.

Signed-off-by: Koen Beel <koen.beel@barco.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:08 -04:00
Guennadi Liakhovetski 162f43e31c mmc: tmio: fix a deadlock
Currently the tmio-mmc driver contains a recursive runtime PM method
invocation, which leads to a deadlock on a mutex. Avoid it by taking
care not to request DMA too early.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:07 -04:00
Guennadi Liakhovetski 332bdb506f mmc: tmio: fix a recently introduced bug in DMA code
A recent commit "mmc: tmio: Share register access functions" has swapped
arguments of a macro and broken DMA with TMIO MMC. This patch fixes the
arguments back.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:07 -04:00
Guennadi Liakhovetski c9b0cef23f mmc: sh_mmcif: maximize power saving
This patch uses runtime PM to allow the system to power down the MMC
controller, when the MMC closk is switched off.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:06 -04:00
Guennadi Liakhovetski 71d111cd34 mmc: tmio: maximize power saving
This patch uses runtime PM to allow the system to power down the MMC
controller, when the MMC closk is switched off.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:06 -04:00
Guennadi Liakhovetski b9269fdd4f mmc: tmio: fix recursive spinlock, don't schedule with interrupts disabled
Calling mmc_request_done() under a spinlock with interrupts disabled
leads to a recursive spin-lock on request retry path and to
scheduling in atomic context. This patch fixes both these problems
by moving mmc_request_done() to the scheduler workqueue.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:05 -04:00
Adrian Hunter 770d743200 mmc: omap_hsmmc: fix oops in omap_hsmmc_dma_cb()
In the case of an I/O error, the DMA will have been cleaned up in
the MMC interrupt and the request structure pointer will be null.

In that case, it is essential to check if the DMA is over before
dereferencing host->mrq->data.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:04 -04:00
Andy Shevchenko 3796fb8ac4 mmc: omap_hsmmc: refactor duplicated code
There are a few places with the same functionality. This patch creates
two functions omap_hsmmc_set_bus_width() and omap_hsmmc_set_bus_mode()
to do the job.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:03 -04:00
Andy Shevchenko 5934df2f10 mmc: omap_hsmmc: fix a few bugs when setting the clock divisor
There are two pieces of code which are similar, but not the same.
Each of them contains a bug.

The SYSCTL register should be read before writing to it in
omap_hsmmc_context_restore() to retain the state of the reserved bits.

Before setting the clock divisor and DTO bits the value from the SYSCTL
register should be masked properly. We were lucky to have no problems
with DTO bits. So, make sure we have clear DTO bits properly in
omap_hsmmc_set_ios().

Additionally get rid of msleep(1). The actual time is rarely higher
than 30us on OMAP 3630.

The resulting pieces of code are refactored into the
omap_hsmmc_set_clock() function.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:03 -04:00
Andy Shevchenko e0c7f99b86 mmc: omap_hsmmc: introduce start_clock and re-use stop_clock
There is similar code in two functions which enable the clock.  Refactor
this code to omap_hsmmc_start_clock(). Re-use omap_hsmmc_stop_clock() in
omap_hsmmc_context_restore() as well.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-21 10:35:02 -04:00