The chipsets with the isa_dma_bridge_buggy set do not stop DMA during
DMA counter reads. The DMA counter is read in two 8-bit read steps
on x86 platform. Sometimes, such reads happen during higher byte
change so the lower byte is already decremented (rolled over) but
the higher byte is not. It introduces an error that position is
moved 256 bytes ahead of the true position. Thus, the next DMA
position read can return a lower value then the previous read.
If the DMA position is decreased (reversed) the ALSA subsystem is
tricked into the playback underrun error and resets the playback.
It results in a "pop" during a playback.
Work around the issue by reading the counter twice and choosing a higher
value.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The C4231 control set is a superset of the AD1848 control
set so reuse the CS4231 controls definitions for the AD1848.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert CS4231 mixer to dB scale after AD1848 mixer.
Also, add missing microphone boost control for the AD1848
and correct wrong bits for loopback volume on the AD1848.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix coding style errors in the driver.
Also, add missing argument for CMD_XXX_MIDI_VOL command.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Module parameters shouldn't be marked as __devinitdata since they can be
referred via sysfs even after probing.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Old Soundscape cards (pre PnP) work only with AD1848 codecs.
If the CS4231 codec is installed it must be used in AD1848
compatible mode.
Also, add gameport support and remove an unused mpu field.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no sense to limit open MIDI connections with limit
as high as ULONG_MAX.
Also, convert more messages to use the snd_printk.
Correct few old and misleading comments as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The conversion solves the problem that firmware size was set to 64KB
while non PnP cards have 128KB firmware files.
An additional firmware initialization code has been moved from the OSS
driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move code from the OSS sscape driver in order to support old Soundscape OEM models.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds support for US-144 when attached on USB1.1.
Unlike the US-122L it uses both USB interfaces 0 and 1.
Signed-off-by: Tobias Hansen <Tobias.Hansen@physik.uni-hamburg.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (38 commits)
x86: Move get/set_wallclock to x86_platform_ops
x86: platform: Fix section annotations
x86: apic namespace cleanup
x86: Distangle ioapic and i8259
x86: Add Moorestown early detection
x86: Add hardware_subarch ID for Moorestown
x86: Add early platform detection
x86: Move tsc_init to late_time_init
x86: Move tsc_calibration to x86_init_ops
x86: Replace the now identical time_32/64.c by time.c
x86: time_32/64.c unify profile_pc
x86: Move calibrate_cpu to tsc.c
x86: Make timer setup and global variables the same in time_32/64.c
x86: Remove mca bus ifdef from timer interrupt
x86: Simplify timer_ack magic in time_32.c
x86: Prepare unification of time_32/64.c
x86: Remove do_timer hook
x86: Add timer_init to x86_init_ops
x86: Move percpu clockevents setup to x86_init_ops
x86: Move xen_post_allocator_init into xen_pagetable_setup_done
...
Fix up conflicts in arch/x86/include/asm/io_apic.h
Signed-off-by: Geoffrey Thomas <geofft@ksplice.com>
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is largely a straightforward conversion. The patch results in
fewer output sections, and some data being reordered, but should have
no functional impact.
Also, note that this patch moves some data (namely, init_task and
cacheline-aligned) inside [_sdata,_edata].
Because frv already builds using -ffunction-sections -fdata-sections,
we can't use BSS_SECTION or RW_DATA_SECTION yet, since they do not
currently include the required .bss.* and .data.* sections.
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It appears that frv copied the .altinstructions definitions in its linker
script from x86. Since frv doesn't put anything in those sections, this
is just dead code.
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (64 commits)
ext4: Update documentation about quota mount options
ext4: replace MAX_DEFRAG_SIZE with EXT_MAX_BLOCK
ext4: Fix the alloc on close after a truncate hueristic
ext4: Add a tracepoint for ext4_alloc_da_blocks()
ext4: store EXT4_EXT_MIGRATE in i_state instead of i_flags
ext4: limit block allocations for indirect-block files to < 2^32
ext4: Fix different block exchange issue in EXT4_IOC_MOVE_EXT
ext4: Add null extent check to ext_get_path
ext4: Replace BUG_ON() with ext4_error() in move_extents.c
ext4: Replace get_ext_path macro with an inline funciton
ext4: Fix include/trace/events/ext4.h to work with Systemtap
ext4: Fix initalization of s_flex_groups
ext4: Always set dx_node's fake_dirent explicitly.
ext4: Fix async commit mode to be safe by using a barrier
ext4: Don't update superblock write time when filesystem is read-only
ext4: Clarify the locking details in mballoc
ext4: check for need init flag in ext4_mb_load_buddy
ext4: move ext4_mb_init_group() function earlier in the mballoc.c
ext4: Make non-journal fsync work properly
ext4: Assure that metadata blocks are written during fsync in no journal mode
...
Remove net/genetlink.h inclusion, now sched.c won't be recompiled
because of some networking changes.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the short description after symbol name and dash in a kernel-doc
comment to span multiple lines, e.g. like this:
/**
* unmap_mapping_range - unmap the portion of all mmaps in the
* specified address_space corresponding to the specified
* page range in the underlying file.
* @mapping: the address space containing mmaps to be unmapped.
* ...
*/
The short description ends with a parameter description, an empty line
or the end of the comment block.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'current' is a pointer, so the right form is 'down_write(¤t->mm->mmap_sem)'.
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kref_put() already occurs after the out label
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] sizeof cleanup
[WATCHDOG] wdt_pci: fix printk and variable type
[WATCHDOG] wdt_pci - use pci_request_region
[WATCHDOG] ar7_wdt: Fix error handling during probe.
[WATCHDOG] ar7_wdt: convert to become a platform driver
[WATCHDOG] fix book E watchdog to take WDIOC_SETTIMEOUT arg in seconds
[WATCHDOG] davinci: use clock framework for timer frequency
[WATCHDOG] Use DIV_ROUND_UP() macro in the coh901327 WDT
[WATCHDOG] Add support for WM831x watchdog
[WATCHDOG] Add watchdog driver for NUC900
[WATCHDOG] add SBC-FITPC2 watchdog driver
* 'for-linus' of git://gitserver.sunplusct.com/linux-2.6-score: (22 commits)
score: add TIF_NOTIFY_RESUME define in asm/thread_info.h
score: make init_thread_union align to THREAD_SIZE
score: update files according to review comments.
score: add old syscall support
score: add MEMORY_START and MEMORY_SIZE define, to make the code clear
score: update inconsistent declare after .c was changed
score: remove unused code, add include files in .c
score: clean up mm/init.c
score: make irq.h definitions local
score: cleanups: dead code, 0 as pointer, shadowed variables
score: fix function prototypes
score: add address space annotations
score: add missing #includes
score: move save arg5 and arg6 instruction in front of enable_irq
score: add prototypes for wrapped syscalls
score: remove init_mm
score: add generic sys_call_table
score: remove __{put,get}_user_unknown
score: unset __ARCH_WANT_IPC_PARSE_VERSION
score: update files according to review comments
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (262 commits)
sh: mach-ecovec24: Add user debug switch support
sh: Kill off unused se_skipped in alignment trap notification code.
sh: Wire up HAVE_SYSCALL_TRACEPOINTS.
video: sh_mobile_lcdcfb: use both register sets for display panning
video: sh_mobile_lcdcfb: implement display panning
sh: Fix up sh7705 flush_dcache_page() build.
sh: kfr2r09: document the PLL/FLL <-> RF relationship.
sh: mach-ecovec24: need asm/clock.h.
sh: mach-ecovec24: deassert usb irq on boot.
sh: Add KEYSC support for EcoVec24
sh: add kycr2_delay for sh_keysc
sh: cpufreq: Include CPU id in info messages.
sh: multi-evt support for SH-X3 proto CPU.
sh: clkfwk: remove bogus set_bus_parent() from SH7709.
sh: Fix the indication point of the liquid crystal of AP-325RXA(AP3300)
sh: Add EcoVec24 romImage defconfig
sh: USB disable process is needed if romImage boot for EcoVec24
sh: EcoVec24: add HIZA setting for LED
sh: EcoVec24: write MAC address in boot
sh: Add romImage support for EcoVec24
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Clean up linker script using standard macros.
[IA64] Use standard macros for page-aligned data.
[IA64] Use .ref.text, not .text.init for start_ap.
[IA64] sgi-xp: fix printk format warnings
[IA64] ioc4_serial: fix printk format warnings
[IA64] mbcs: fix printk format warnings
[IA64] pci_br, fix infinite loop in find_free_ate()
[IA64] kdump: Short path to freeze CPUs
[IA64] kdump: Try INIT regardless of
[IA64] kdump: Mask INIT first in panic-kdump path
[IA64] kdump: Don't return APs to SAL from kdump
[IA64] kexec: Unregister MCA handler before kexec
[IA64] kexec: Make INIT safe while transition to
[IA64] kdump: Mask MCA/INIT on frozen cpus
Fix up conflict in arch/ia64/kernel/vmlinux.lds.S as per Tony's
suggestion.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: add fusectl interface to max_background
fuse: limit user-specified values of max background requests
fuse: use drop_nlink() instead of direct nlink manipulation
fuse: document protocol version negotiation
fuse: make the number of max background requests and congestion threshold tunable
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (62 commits)
DaVinci: DM646x - platform changes for vpif capture and display drivers
davinci: DM355 - platform changes for vpfe capture
davinci: DM644x platform changes for vpfe capture
davinci: audio: move tlv320aic33 i2c setup into board files
DaVinci: EDMA: Adding 2 new APIs for allocating/freeing PARAMs
DaVinci: DM365: Adding entries for DM365 IRQ's
DaVinci: DM355: Adding PINMUX entries for DM355 Display
davinci: Handle pinmux conflict between mmc/sd and nor flash
davinci: Add NOR flash support for da850/omap-l138
davinci: Add NAND flash support for DA850/OMAP-L138
davinci: Add MMC/SD support for da850/omap-l138
davinci: Add platform support for da850/omap-l138 GLCD
davinci: Macro to convert GPIO signal to GPIO pin number
davinci: Audio support for DA850/OMAP-L138 EVM
davinci: Audio support for DA830 EVM
davinci: Correct the number of GPIO pins for da850/omap-l138
davinci: Configure MDIO pins for EMAC
DaVinci: DM365: Add Support for new Revision of silicon
DaVinci: DM365: Fix Compilation issue due to PINMUX entry
DaVinci: EDMA: Updating default queue handling
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use kernel_sendpage
dlm: fix connection close handling
dlm: fix double-release of socket in error exit path
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
ext3: Flush disk caches on fsync when needed
ext3: Add locking to ext3_do_update_inode
ext3: Fix possible deadlock between ext3_truncate() and ext3_get_blocks()
jbd: Annotate transaction start also for journal_restart()
jbd: Journal block numbers can ever be only 32-bit use unsigned int for them
ext3: Update MAINTAINERS for ext3 and JBD
JBD: round commit timer up to avoid uncommitted transaction
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix NULL ptr regression in powernow-k8
[CPUFREQ] Create a blacklist for processors that should not load the acpi-cpufreq module.
[CPUFREQ] Powernow-k8: Enable more than 2 low P-states
[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)
[CPUFREQ] ondemand - Use global sysfs dir for tuning settings
[CPUFREQ] Introduce global, not per core: /sys/devices/system/cpu/cpufreq
[CPUFREQ] Bail out of cpufreq_add_dev if the link for a managed CPU got created
[CPUFREQ] Factor out policy setting from cpufreq_add_dev
[CPUFREQ] Factor out interface creation from cpufreq_add_dev
[CPUFREQ] Factor out symlink creation from cpufreq_add_dev
[CPUFREQ] cleanup up -ENOMEM handling in cpufreq_add_dev
[CPUFREQ] Reduce scope of cpu_sys_dev in cpufreq_add_dev
[CPUFREQ] update Doc for cpuinfo_cur_freq and scaling_cur_freq
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (34 commits)
time: Prevent 32 bit overflow with set_normalized_timespec()
clocksource: Delay clocksource down rating to late boot
clocksource: clocksource_select must be called with mutex locked
clocksource: Resolve cpu hotplug dead lock with TSC unstable, fix crash
timers: Drop a function prototype
clocksource: Resolve cpu hotplug dead lock with TSC unstable
timer.c: Fix S/390 comments
timekeeping: Fix invalid getboottime() value
timekeeping: Fix up read_persistent_clock() breakage on sh
timekeeping: Increase granularity of read_persistent_clock(), build fix
time: Introduce CLOCK_REALTIME_COARSE
x86: Do not unregister PIT clocksource on PIT oneshot setup/shutdown
clocksource: Avoid clocksource watchdog circular locking dependency
clocksource: Protect the watchdog rating changes with clocksource_mutex
clocksource: Call clocksource_change_rating() outside of watchdog_lock
timekeeping: Introduce read_boot_clock
timekeeping: Increase granularity of read_persistent_clock()
timekeeping: Update clocksource with stop_machine
timekeeping: Add timekeeper read_clock helper functions
timekeeping: Move NTP adjusted clock multiplier to struct timekeeper
...
Fix trivial conflict due to MIPS lemote -> loongson renaming.
Commit ac89a9174 ("pty: don't limit the writes to 'pty_space()' inside
'pty_write()'") removed the pty_space() checking, in order to let the
regular tty buffer code limit the buffering itself.
That was all good, but as a subtle side effect it meant that we'd be
doing a tty_wakeup() even in the case where the buffers were all filled
up, and didn't actually make any progress on the write.
Which sounds innocuous, but it interacts very badly with the ppp_async
code, which has an infinite loop in ppp_async_push() that tries to push
out data to the tty. When we call tty_wakeup(), that loop ends up
thinking that progress was made (see the subtle interactions between
XMIT_WAKEUP and 'tty_stuffed' for details). End result: one unhappy ppp
user.
Fixed by noticing when tty_insert_flip_string() didn't actually do
anything, and then not doing any more processing (including, very much
not calling tty_wakeup()).
Bisected-and-tested-by: Peter Volkov <pva@gentoo.org>
Cc: stable@kernel.org (2.6.31)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix printk format warning:
drivers/watchdog/wdt_pci.c:652: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
and then use resource_size_t for the "io" variable as well
so that it won't be truncated.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch converts the ar7_wdt driver to become
a platform driver. The AR7 SoC specific identification
and base register calculation is performed by the board
code, therefore we no longer need to have access to
ar7_chip_id. We also remove the reboot notifier code to
use the platform shutdown method as Wim suggested.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDIOC_SETTIMEOUT argument is supposed to be a "seconds" value.
However, the book E wdt currently treats it as a "period" which is
interpreted in a board-specific way.
This patch allows the user to pass in a "seconds" value and the driver
will set the smallest timeout that is at least as large as specified
by the user. It's been tested on e500 hardware and works as
expected.
The patch only modifies the CONFIG_FSL_BOOKE case, the CONFIG_4xx case
is left unmodified as I don't have any hardware to test it on.
Signed-off-by: Chris Friesen <cfriesen@nortel.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove use of CLOCK_TICK_RATE in favor of using clock framework
for getting timer frequency.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I saw Julia Lawalls various commits fixing up the use of rounding
macros and since my already submitted patch was not caught in this
I took it upon myself to fix it up for this driver as well.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WM831x series of devices provide a watchdog with configurable
behaviour on timer expiry.
Currently this driver support refreshes via a register or GPIO line and
autonomous refreshes from a hardware source (eg, a clock).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add watchdog device driver for the Nuvoton NUC900 series SoCs.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for watchdog found on SBC-FITPC2 board.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (21 commits)
x86, mce: Fix compilation with !CONFIG_DEBUG_FS in mce-severity.c
x86, mce: CE in last bank prevents panic by unknown MCE
x86, mce: Fake panic support for MCE testing
x86, mce: Move debugfs mce dir creating to mce.c
x86, mce: Support specifying raise mode for software MCE injection
x86, mce: Support specifying context for software mce injection
x86, mce: fix reporting of Thermal Monitoring mechanism enabled
x86, mce: remove never executed code
x86, mce: add missing __cpuinit tags
x86, mce: fix "mce" boot option handling for CONFIG_X86_NEW_MCE
x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUs
x86: mce: Lower maximum number of banks to architecture limit
x86: mce: macros to compute banks MSRs
x86: mce: Move per bank data in a single datastructure
x86: mce: Move code in mce.c
x86: mce: Rename CONFIG_X86_NEW_MCE to CONFIG_X86_MCE
x86: mce: Remove old i386 machine check code
x86: mce: Update X86_MCE description in x86/Kconfig
x86: mce: Make CONFIG_X86_ANCIENT_MCE dependent on CONFIG_X86_MCE
x86, mce: use atomic_inc_return() instead of add by 1
...
Manually fixed up trivial conflicts:
Documentation/feature-removal-schedule.txt
arch/x86/kernel/cpu/mcheck/mce.c
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
sched: Fix SD_POWERSAVING_BALANCE|SD_PREFER_LOCAL vs SD_WAKE_AFFINE
sched: Stop buddies from hogging the system
sched: Add new wakeup preemption mode: WAKEUP_RUNNING
sched: Fix TASK_WAKING & loadaverage breakage
sched: Disable wakeup balancing
sched: Rename flags to wake_flags
sched: Clean up the load_idx selection in select_task_rq_fair
sched: Optimize cgroup vs wakeup a bit
sched: x86: Name old_perf in a unique way
sched: Implement a gentler fair-sleepers feature
sched: Add SD_PREFER_LOCAL
sched: Add a few SYNC hint knobs to play with
sched: Fix sync wakeups again
sched: Add WF_FORK
sched: Rename sync arguments
sched: Rename select_task_rq() argument
sched: Feature to disable APERF/MPERF cpu_power
x86: sched: Provide arch implementations using aperf/mperf
x86: Add generic aperf/mperf code
x86: Move APERF/MPERF into a X86_FEATURE
...
Fix up trivial conflict in arch/x86/include/asm/processor.h due to
nearby addition of amd_get_nb_id() declaration from the EDAC merge.
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pat: don't use rb-tree based lookup in reserve_memtype()
x86: Increase MIN_GAP to include randomized stack
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (44 commits)
vsnprintf: remove duplicate comment of vsnprintf
softirq: add BLOCK_IOPOLL to softirq_to_name
oprofile: fix oprofile regression: select RING_BUFFER_ALLOW_SWAP
tracing: switch function prints from %pf to %ps
vsprintf: add %ps that is the same as %pS but is like %pf
tracing: Fix minor bugs for __unregister_ftrace_function_probe
tracing: remove notrace from __kprobes annotation
tracing: optimize global_trace_clock cachelines
MAINTAINERS: Update tracing tree details
ftrace: document function and function graph implementation
tracing: make testing syscall events a separate configuration
tracing: remove some unused macros
ftrace: add compile-time check on F_printk()
tracing: fix F_printk() typos
tracing: have TRACE_EVENT macro use __flags to not shadow parameter
tracing: add static to generated TRACE_EVENT functions
ring-buffer: typecast cmpxchg to fix PowerPC warning
tracing: add filter event logic to special, mmiotrace and boot tracers
tracing: remove trace_event_types.h
tracing: use the new trace_entries.h to create format files
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
pata_amd: do not filter out valid modes in nv_mode_filter
sata_promise: update reset code
sata_promise: disable hotplug on 1st gen chips
libata: fix spurious WARN_ON_ONCE() on port freeze
ahci: restore pci_intx() handling
Krzysztof Helt