This patch adds n-tuple filter programming to 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break the largish case for handling receive checksum into a separate
function, and if there is a problem use dev_XXX routines to
show which hardware is the problem.
Turn one corner case into a BUG(). This only happens if the driver
is expecting one behavior but the chip does the old behavior;
only ever saw this when bringing up a new chip type and driver
was buggy.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clone of vendor code to disable ASF on Extreme and Supreme chips.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the resume path to use pci write config for a couple of reasons:
1. pci_write_config_dword() allows for more error
checking of PCI health after resume.
2. better to toggle this register on all chip types, since that
is what vendor driver does.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for using the libertas_tf driver on a managed
or ad-hoc network.
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware needs to know what type of frames are being
sent in order to fill in various fields, for example the
timestamp in probe responses (before this patch, it was
always 0). Set it correctly when initializing the TX
descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
i.MX51 babbage board has a FEC ethernet controller
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX51 babbage board has a FEC ethernet controller with this phy.
In the long term we should resurrect the phylib patches for fec.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fec driver was enabling receive buffer descriptor without allocating
the buffers. Make sure the buffer descriptors are initialized to not
start receiving packets.
Open also calls fec_restart after the rx buffers are allocated. With the code
in fec_restart, it zeroes out the buffer descriptors that have just been
setup.
Signed-off-by: Rob Herring <r.herring@freescale.com>
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two potential races in the velocity driver:
* Move the ACK and error handler to the interrupt handler. This fixes a
potential race with shared interrupts when the other device interrupts
before the NAPI poll handler has finished. As the velocity driver hasn't
acked it's own interrupt, it will then steal the interrupt from the
other device.
* Use spin_lock_irqsave in velocity_poll. In the current code, the
interrupt handler will deadlock if e.g., the NAPI poll handler is
executing when an interrupt (for another device) comes in since it
tries to take the already held lock.
Also unlock the spinlock only after enabling the interrupt in
velocity_poll.
The error path is moved to the interrupt handler since this is where the
ISR is checked now.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Anders Grafstrom <anders.grafstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
velocity_set_coalesce touches ISR and some other sensitive registers not
covered by the rtnl lock, so take the velocity spinlock.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new RTL8187B device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wrong pointer was tested.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, PAE frames are not assigned proper sequence numbers.
Since sending PAE frames as part of aggregates breaks
crupto with several APs, they are sent as normal MPDUs.
Fix the seqeuence number issue by updating the frame with the
internal sequence number.
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Test the value that was just allocated rather than the previously tested one.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify the HW checksum state for frames handed to GRO processing.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a WARN_ON which is triggered
by Poland's country code.
ath: EEPROM regdomain: 0x8268
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x37
ath: Country alpha2 being used: PL
ath: Regpair used: 0x37
-----------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/regd.c:155 ath_regd_init+0x30b
Pid: 12661, comm: firmware/carl91 2.6.33-rc5-wl #18
Call Trace:
[<>] ? warn_slowpath_common+0x76/0x8c
[<>] ? ar9170_reg_notifier+0x0/0x2d [carl9170usb]
[<>] ? ath_regd_init+0x30b/0x377 [ath]
[<>] ? ar9170_register+0x3b3/0x3ca [carl9170usb]
[...]
---[ end trace ]---
Note: Poland is just an example. But it is very likely
that more country codes are affected.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
p54 uses struct ieee80211_tx_queue_stats also internally, so create a new
identical struct p54_tx_queue_stats which the driver can use.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Because ar9170 uses ieee80211_tx_queue_stats internally, create a new
identical struct ar9170_tx_queue_stats which the driver can use.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
mwl8k used struct ieee80211_tx_queue_stats internally to track the queue
lenght. Replace struct ieee80211_tx_queue_stats with a simple len field
in struct mwl8k_tx_queue. Limit and count fields seemed to be unused.
Compile-tested only.
Cc: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If split tkip key is used, ath_delete_key should delete
rx key and rx mic key. This patch fixes the leak of hw
keycache in the case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running directed active scans we currently end up sending both the SSID
probe requests and an additional broadcast one.
This is due to the fact that we always leave the probe request template SSID IE
length to 0. Instead we should set it to the first SSID to scan, and fill the
direct_scan array with the remaining SSIDs to scan for. This way we only send
what we've been asked to: a broadcast probe request when no directed scan is
requested, and directed probe requests otherwise.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing iwl6050_ops->iwl6050_hcmd_utils structure had no pointers to chain
noise functions (gain_computation and chain_noise_reset). As it turns out,
by adding chain_noise_scale (see related patch), there is no need for separate
chain noise function, so simply use iwl6000_ops->iwl5000_hcmd_utils, and
remove those for 6050.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
6x50 device requires a different scaling factor for Rx gain values sent to
device via PHY_CALIBRATION_CMD (CHAIN_NOISE_GAIN_CMD). Rather than create
a new iwlXXXX_gain_computation() function, add new chain_noise_scale member
to struct iwl_cfg, and keep using iwl5000_gain_computation().
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retrying commands seldomly works, most often the firmware is in a
weird state anyway and needs the device to reset. So it's better
to report the broken state back to user-space.
Also rename command_timer_fn() into lbs_cmd_timeout_handler(),
which better reflect it's usage.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 uses unit units of 32 usec with txop but wl1251_acx_ac_cfg()
expects it to be usecs. This fortunately didn't cause any severe problems,
only that firmware was using incorrect WMM settings.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libertas/if_spi.c needs to #include linux/semaphore.h to fix build errors:
drivers/net/wireless/libertas/if_spi.c:59: error: field 'spi_ready' has incomplete type
drivers/net/wireless/libertas/if_spi.c:60: error: field 'spi_thread_terminated' has incomplete type
drivers/net/wireless/libertas/if_spi.c:785: error: implicit declaration of function 'down_interruptible'
drivers/net/wireless/libertas/if_spi.c:787: error: implicit declaration of function 'up'
drivers/net/wireless/libertas/if_spi.c:834: error: implicit declaration of function 'down'
drivers/net/wireless/libertas/if_spi.c:943: error: implicit declaration of function 'sema_init'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If b43 or b43legacy are deauthenticated or disconnected, there is a
possibility that a reconnection is tried with the queues stopped in
mac80211. To prevent this, start the queues before setting
STAT_INITIALIZED.
In b43, a similar change has been in place (twice) in the
wireless_core_init() routine. Remove the duplicate and add similar
code to b43legacy.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM timer interrupt is enabled even before the ACK of nullqos
is received which is unnecessary.
Also clean up the CONF_PS part of config callback properly for
better readability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
beacons configuration SHOULD be done only if the STA is associated.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For debugging hardware scan trigger/complete
functionality, it was useful to have code in
hwsim that pretends to do a hardware scan.
This code could be extended to actually do the
scan, but for now it was sufficient for me to
only pretend. Since hwsim was written to ease
debugging, it only makes sense to add it to it
permanently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_set_rxon_ht() only get called in iwl_post_associate(); which cause
possible incorrect ht configuration. Adding the call in iwl_mac_config() if
IEEE80211_CONF_CHANGE_CHANNEL flag is set to re-configure and send rxon
command.
Fixes
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2146
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just reordering this assignment that doesn't depend on any
condition.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the qlge_change_mtu() is never called if the new_mtu is
equal current MTU, due this condition on dev_set_mtu():
if (new_mtu == dev->mtu)
return 0;
So, this block of code is never reached and is being removed.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add periodic heartbeat register read to trigger the eeh
recovery process.
We see cases where an eeh error was injected and the slot was
suspended. An asic access attempt is required to flush the recovery process,
but without interrupts the process can stall.
Adding this periodic register read causes the recovery process to begin.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers do this in them manually. Now they can use this function.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects an issue that will cause false hangs when using either
82575 or 82580 in legacy interrupt mode. The issue is caused when there is
a slow traffic flow and an "ethtool -r" is executed while using legacy or
MSI interrupts. MSI-X is not affected by this issue due to the fact that
we were already reconfiguring the vectors after reset.
If possible it would be best to push this for net-2.6 since it is resolving
a bug but if that is not possible then net-next-2.6 will be fine.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks for your patch. A more general solution would be to move the
rx_dropped up into sky2_receive.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If receive buffer mapping failed, then it was possible to get
stuck with unmapped receive buffer in DMA ring.
This would be an extremely rare condition because the driver had just
released the map for the last receive so it should be able to get
another map again (in soft-irq).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses concerns about efficiency of handling incoming
packets. Handling of interrupts is done in a threaded interrupt handler
which has a smaller latency than workqueues. This change needed a rework
of the locking scheme that was much simplified. Some other (more or less
longstanding) bugs are fixed: utilization of just half of the RX
buffers, useless wait for interrupt on open, more reliable reset
sequence. The MERR interrupt is not used anymore: it overloads the CPU
in error-passive state without any additional information. One shot mode
is disabled because it's not clear if it can be handled efficiently on
this CAN controller.
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to maintain stats in the bonding structure.
Use the instance of net_device_stats in netdevice.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use macvlan with qemu and other tools that require
a tap file descriptor, the macvtap driver adds a small backend
with a character device with the same interface as the tun
driver, with a minimum set of features.
Macvtap interfaces are created in the same way as macvlan
interfaces using ip link, but the netif is just used as a
handle for configuration and accounting, while the data
goes through the chardev. Each macvtap interface has its
own character device, simplifying permission management
significantly over the generic tun/tap driver.
Cc: Patrick McHardy <kaber@trash.net>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: David S. Miller" <davem@davemloft.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Or Gerlitz <ogerlitz@voltaire.com>
Cc: netdev@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it possible to hook into the macvlan driver
from another kernel module. In particular, the goal is
to extend it with the macvtap backend that provides
a tun/tap compatible interface directly on the macvlan
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the vlan and macvlan drivers, the start_xmit function forwards
data to the dev_queue_xmit function for another device, which may
potentially belong to a different namespace.
To make sure that classification stays within a single namespace,
this resets the potentially critical fields.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix crash where resources are freed twice on an eeh recovery failure.
If eeh recovery fails we set a flag to indicate to close() that
resources have been freed.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue asic reset and verify functionality before continuing to the
resume call. This allows proper error code to be returned in the case
the asic does not recover.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allocates the ring structures themselves on each
NUMA node along with the buffer_info structures. This way we
don't allocate the entire ring memory on a single node in one
big block, thus reducing NUMA node memory crosstalk.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default policy for the current driver is to do all its memory
allocation on whatever processor is running insmod/modprobe. This
is less than optimal.
This driver's default mode of operation will be to use each node for each
subsequent transmit/receive queue. The most efficient allocation will be
to then have the interrupts bound in such a way as to match up the
interrupt of the queue to the cpu where its memory was allocated.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to pci_save_state() immediately after
the call to pci_restore_state(). Due to a change in the behavior
of pci_restore_state() it is necessary to call pci_save_state()
to keep the state_saved flag. This patch is based on a similar
patch for ixgbe.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this change ethtool will correctly report link status when
the interface is down. Currently ethtool reports the link as not
detected when the interface is down.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing multiple ixgbe_watchdog_task calls may cause
the link_up variable and IXGBE_FLAG_NEED_LINK_UPDATE flag
to be set incorrectly. In the worse case this is causing
the netif_carrier_off to be called inappropriately which
results in an interface that can't be brought up.
Although schedule_work() will only schedule the task if
it is not already on the work queue the WORK_STRUCT_PENDING
bits are cleared just before calling the work function.
This allows WORK_STRUCT_PENDING to be cleared, the work
function to start and meanwhile schedule another task.
This patch adds a mutex to the watchdog task. This bug is
actualized by changing DCB settings or doing extended
cable pull or reset tests.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a developer had complained of getting lots of warnings:
"eth16 selects TX queue 98, but real number of TX queues is 64"
http://www.mail-archive.com/e1000-devel@lists.sourceforge.net/msg02200.html
As there was no follow up on that bug, I am submitting this
patch assuming that the other return points will not return
invalid txq's, and also that this fixes the bug (not tested).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e5a43549f7 (ixgbe: remove
skb_dma_map/unmap calls from driver) looks to have introduced a bug in
ixgbe_tx_map. If we get an error from a PCI DMA call, we loop backwards
through count until it becomes -1 and return that.
The caller of ixgbe_tx_map expects 0 on error, so return that instead.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o context resources can be in used, while resource cleanup is in progress,
during fw recover.
o Null pointer execption can occur in send_cmd_desc, if fw recovery
module frees tx ring without rtnl lock.
o Same applies to ethtool register dump.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NX2031, first try to scrub interrupt before requesting firmware
reset. Return statement was missing after scrubbbing interrupt.
Signed-off-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier refactoring has made these inclusions unnecessary.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, the comment about EVQ_RPTR_REG is based on inconsistent
preliminary hardware documentation, though the following code was
fixed long before release.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFC9000-family boards do not all use MDIO PHYs, so we need a different
test for PHY aliveness.
Introduce a PHY operation test_alive(). For PHYs attached to Falcon,
use a common implementation based on the existing PHY MDIO test.
For PHYs managed through MCDI, use the appropriate MCDI request.
Change test name in ethtool from 'core mdio' to 'phy alive'.
Rename test_results::mdio to phy_alive and test_results::phy to phy_ext.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the driver to recover if the MC firmware has crashed due
to an assertion failure.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is for CAN interface cards based on the PLX90xx PCI bridge.
Driver supports now:
- Adlink PCI-7841/cPCI-7841 card (http://www.adlinktech.com/)
- Adlink PCI-7841/cPCI-7841 SE card
- Marathon CAN-bus-PCI card (http://www.marathon.ru/)
- TEWS TECHNOLOGIES TPMC810 card (http://www.tews.com/)
Changes since v1:
- Added some defines for static inline int plx_pci_check_sja1000(...)
- static struct pci_device_id plx_pci_tbl[] replaced by
static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl)
- Typo fixed
Signed-off-by: Pavel Cheblakov <P.B.Cheblakov@inp.nsk.su>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add memory barriers to fix crashes observed on newest PowerPC platforms.
The HW and driver state of the receive rings were getting out of sync.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The book keeping structure for transmit always had the flags value
cleared so transmit DMA maps were never released correctly.
Based on patch by Jarek Poplawski, problem observed by Michael Breuer.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ChangeLog:
Implement .reset_resume support to retain a live network connection
during suspend despite USB power loss.
- rework operation to reference cached data in mcs7830_data and
netdev->dev_addr
- update netdev->dev_addr only in case new MAC was set successfully
. Tests done:
. ethtool -d pre-/post-suspend: register values match
. running ssh session suspend, resume: works
. ifdown device, suspend, resume: works
. ifup, suspend, unplug, resume: WORKS (eth1 is removed, re-ifup of eth1
after card replug works)
. verified identical MAC in ifconfig post-resume
(ok, should be verified on network side to be fully certain...)
Keywords: suspend resume network connection dead interface down
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ChangeLog:
- evaluate Rx error statistics from trailing Rx status byte
- add driver TODO list
- add myself to authors
Quilt series run-tested, based on 2.6.33-rc4 (net-2.6.git mcs7830 has idle history,
should be good to go).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c7ab5ef9bc entitled "b43: implement
short slot and basic rate handling" reduced the transmit throughput for
my BCM4311 device from 18 Mb/s to 0.7 Mb/s. The basic rate handling
portion is OK, the problem is in the short slot handling.
Prior to this change, the short slot enable/disable routines were never
called. Experimentation showed that the critical part was changing the
value at offset 0x0010 in the shared memory. This is supposed to contain
the 802.11 Slot Time in usec, but if it is changed from its initial value
of zero, performance is destroyed. On the other hand, changing the value
in the MMIO register corresponding to the Interframe Slot Time increased
performance from 18 to 22 Mb/s. A BCM4306/3 also shows dramatic
improvement of the transmit rate from 5.3 to 19.0 Mb/s.
Other changes in the patch include removal of the magic number for the
MMIO register, and allowing the slot time to be set for any PHY operating
in the 2.4 GHz band. Previously, the routine was executed only for G PHYs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [Any stable version back through 2.6.28]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Loopback test (offline) added in ethtool self test.
o Set device in loopback mode
o Send packets
o Process receive packets in qlcnic_process_rcv_ring_diag()
o Compare packets
o Reset device in normal mode.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt test (offline) added in ethtool self test.
Register a temporary interrupt handler and then send command to fw
to raise an interrupt.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support of device identification by blinking LED for specified time.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o context resources can be in used, while resoruce cleanup is in progress,
during fw recover.
o Null pointer execption can occur in send_cmd_desc, if fw recovery
module frees tx ring without rtnl lock.
o Same applies to ethtool register dump and FW health registers should be dump
in any case.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o After firmware recovery, clear device reset state transition register.
Otherwise firmware reload can occur unnecessary.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added missing identifier that distinguishes between
FCOE/ISCSI/ETHERNET functions.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into
correct section in every case.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Btw of the dma-debug problem reported by Michael Breuer I spotted
a tiny misspelling in TX_MAP_PAGE definition introduced by commit
6b84dacadb.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_net receives packets from its pre-allocated vring buffers, then it
delivers these packets to upper layer protocols as skb buffs. So it's not
necessary to pre-allocate skb for each mergable buffer, then frees extra
skbs when buffers are merged into a large packet. This patch has deferred
skb allocation in receiving packets for both big packets and mergeable buffers
to reduce skb pre-allocations and skb frees. It frees unused buffers by calling
detach_unused_buf in vring, so recv skb queue is not needed.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some single chip family devices are sold in the market with
802.11n bonded out, these have no hardware capability for
802.11n but ath9k can still support them. These are called
AR2427.
Cc: stable@kernel.org
Reported-by: Rolf Leggewie <bugzilla.kernel.org@rolf.leggewie.biz>
Tested-by: Bernhard Reiter <ockham@raz.or.at>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch prevents call set_wep_key() with zero key length. That fix long
standing regression since commit c038069352
"airo: clean up WEP key operations". Additionally print call trace when
someone will try to use improper parameters, and remove key.len = 0
assignment, because it is in not possible code path.
Reported-by: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu>
Bisected-by: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu>
Tested-by: Chris Siebenmann <cks@cs.toronto.edu>
Cc: Dan Williams <dcbw@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cev-isr reg offset for each function is better calculated using (any) eq-id
alloted to that function instead of using pci-func number(which
does not work in some configurations...)
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is very simple IrDA SIR driver for SuperH.
This driver was tested by irdaping/ircp on SH7724 EcoVec24 board
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling ath_bus_cleanup() after ieee80211_free_hw() resulted in access
to common->bus_ops, which is already freed as part of the device data.
Remove the cleanup field in struct ath_bus_ops, as it was never used
properly. Remove ath_bus_cleanup(). Merge cleanup functions in place
of the ath_bus_cleanup() calls. Take care not to use any device data
after ieee80211_free_hw().
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using stack for that causes warnings with CONFIG_FRAME_WARN=1024
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Numeric channel is hard to get, so it won't be printed. Replace Mhz
with MHz on the affected lines and add commas as needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME and xircom_cb from pr_<level>
Convert embedded function names in logging messages to %s, __func__
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Convert %d.%d.%d.%d to %pI4
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME from logging messages
Add do {} while(0) to ULI526X_DBUG macro
Make SHOW_MEDIA_TYPE macro more readable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove 'DRV_NAME ": ' from logging messages
Convert commented out printks to pr_debug
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where appropriate
Convert printks to pr_<level>
Change print formats with %d.dx to %0dx
Coalesce long formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwl_power_update_mode expects to be called with mutex held, for example to
protect priv->vif. Only one caller currently does not do this, fix this.
Also, add a comment to iwl_power_update_mode to indicate this requirement.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Due to a typo, the variable contains OFDM
rates as well. The only user doesn't care,
so this change doesn't really do anything
but fix up my confusion.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
auth_work, calibrated_work, update_link_led
and report_work are never used, so remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
There's no need to queue a work struct from
within a work struct, just move the code to
execute directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move the waiting into iwl5000_load_section instead
of duplicating it in the caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 will only enable powersaving for station mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Update sensitivity range values for 1000 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Update sensitivity range values for 5x00 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Update sensitivity range values for 6000 & 6x50 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The corresponding iwl_mac_remove_interface only
acquires the mutex, leading me to believe that
the spinlock is not necessary. However, this
doesn't actually acquire the mutex around the
vif pointer check and assignment, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Peter Waskiewicz