Commit Graph

51 Commits

Author SHA1 Message Date
Antoine Ténart e5b3b2d9ed pinctrl: allows not to define the get_group_pins operation
When using a group only pinctrl driver, which does not have any
information on the pins it is useless to define a get_group_pins
always returning an empty list of pins.

When not using get_group_pin[1], a driver must implement it so
pins = NULL and num_pins = 0. This patch makes it the default
behaviour if not defined in the pinctrl driver when used in
pinmux enable and disable funtions and in pinctrl_groups_show.

It also adds a check in pinctrl_get_group_pins and return -EINVAL if
not defined. This function is called in the gpiolib when adding when
pingroup range. It cannot be used if no group is defined, so this seams
reasonable.

[1] get_group_pin(struct pinctrl_dev *pctldev,
		  unsigned selector,
		  const unsigned **pins,
		  unsigned *num_pins);

Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-04-22 14:47:02 +02:00
Michael Opdenacker 808e657c5c pinctrl: remove minor dead code
This removes a test whether the 'desc' variable is NULL.
This possibility has already been eliminated by the
below test earlier in the loop:

                if (desc == NULL) {
                        dev_warn(pctldev->dev,
                                 "could not get pin desc for pin %d\n",
                                 pins[i]);
                        continue;
                }

Found with Coverity: CID #1090078

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-04 13:07:05 +01:00
Linus Walleij 1c8e794432 pinctrl: improve warning messages
Print out the affected group name on activation of pin mux
settings, and warn if you cannot free a pin that should have
been part of a certain setting.

ChangeLog v1->v2:
- Also print the pin name in the error messages.

Cc: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-08-14 22:49:14 +02:00
Sonic Zhang 744f0a9adb pinctrl: pinmux: Don't free pins requested by other devices in pinmux_disable_setting.
One peripheral may share part of its pins with the 2nd
peripheral and the other pins with the 3rd. If it requests all pins
when part of them has already be requested and owned by the 2nd
peripheral, this request fails and pinmux_disable_setting() is called.
The pinmux_disable_setting() frees all pins of the first peripheral
without checking if the pin is owned by itself or the 2nd, which
results in the malfunction of the 2nd peripheral driver.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-08-14 17:52:18 +02:00
Patrice Chotard 42fed7ba44 pinctrl: move subsystem mutex to pinctrl_dev struct
This mutex avoids deadlock in case of use of multiple pin
controllers. Before this modification, by using a global
mutex, deadlock appeared when, for example, a call to
pinctrl_pins_show() locked the pinctrl_mutex, called the
ops->pin_dbg_show of a particular pin controller. If this
pin controller needs I2C access to retrieve configuration
information and I2C driver is using pinctrl to drive its
pins, a call to pinctrl_select_state() try to lock again
pinctrl_mutex which leads to a deadlock.

Notice that the mutex grab from the two direction functions
was moved into pinctrl_gpio_direction().

For several cases, we can't replace pinctrl_mutex by
pctldev->mutex, because at this stage, pctldev is
not accessible :
	- pinctrl_get()/pinctrl_put()
	- pinctrl_register_maps()

So add respectively pinctrl_list_mutex and
pinctrl_maps_mutex in order to protect
pinctrl_list and pinctrl_maps list instead.

Reintroduce pinctrldev_list_mutex in
find_pinctrl_by_of_node(),
pinctrl_find_and_add_gpio_range()
pinctrl_request_gpio(), pinctrl_free_gpio(),
pinctrl_gpio_direction(), pinctrl_devices_show(),
pinctrl_register() and pinctrl_unregister() to
protect pinctrldev_list.

Changes v2->v3:
- Fix a missing EXPORT_SYMBOL_GPL() for pinctrl_select_state().

Changes v1->v2:
- pinctrl_select_state_locked() is removed, all lock mechanism
  is located inside pinctrl_select_state(). When parsing
  the state->setting list, take the per-pin-controller driver
  lock. (Patrice).
- Introduce pinctrldev_list_mutex to protect pinctrldev_list
  in all functions which parse or modify pictrldev_list.
  (Patrice).
- move find_pinctrl_by_of_node() from pinctrl/devicetree.c to
  pinctrl/core.c in order to protect pinctrldev_list.
  (Patrice).
- Sink mutex:es into some functions and remove some _locked
  variants down to where the lists are actually accessed to
  make things simpler. (Linus)
- Drop *all* mutexes completely from pinctrl_lookup_state()
  and pinctrl_select_state() - no relevant mutex was taken
  and it was unclear what this was protecting against. (Linus)

Reported by : Seraphin Bonnaffe <seraphin.bonnaffe@stericsson.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-04-26 17:01:35 +02:00
Richard Genoud 740924a267 pinmux: forbid mux_usecount to be set at UINT_MAX
If pin_free is called on a pin already freed, mux_usecount is set to
UINT_MAX which is really a bad idea.

This will issue a warning, so that we can correct the code responsible
for the double free.

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-03-21 19:26:18 +01:00
Axel Lin e38d457de7 pinctrl: pinmux: Release all taken pins in pinmux_enable_setting error paths
Currently pinmux_enable_setting does not release all taken pins if
ops->enable() returns error. This patch ensures all taken pins are
released in any error paths.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-11-11 20:18:32 +01:00
Linus Walleij 1a78958dc2 pinctrl: reserve pins when states are activated
This switches the way that pins are reserved for multiplexing:

We used to do this when the map was parsed, at the creation of
the settings inside the pinctrl handle, in pinmux_map_to_setting().

However this does not work for us, because we want to use the
same set of pins with different devices at different times: the
current code assumes that the pin groups in a pinmux state will
only be used with one single device, albeit different groups can
be active at different times. For example if a single I2C driver
block is used to drive two different busses located on two
pin groups A and B, then the pins for all possible states of a
function are reserved when fetching the pinctrl handle: the
I2C bus can choose either set A or set B by a mux state at
runtime, but all pins in both group A and B (the superset) are
effectively reserved for that I2C function and mapped to the
device. Another device can never get in and use the pins in
group A, even if the device/function is using group B at the
moment.

Instead: let use reserve the pins when the state is activated
and drop them when the state is disabled, i.e. when we move to
another state. This way different devices/functions can use the
same pins at different times.

We know that this is an odd way of doing things, but we really
need to switch e.g. an SD-card slot to become a tracing output
sink at runtime: we plug in a special "tracing card" then mux
the pins that used to be an SD slot around to the tracing
unit and push out tracing data there instead of SD-card
traffic.

As a side effect pinmux_free_setting() is unused but the stubs
are kept for future additions of code.

Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Loic Pallardy <loic.pallardy@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Jean Nicolas Graux <jean-nicolas.graux@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-11-11 19:05:56 +01:00
Thomas Petazzoni 23a895aee6 pinctrl: use kasprintf() in pinmux_request_gpio()
Instead of using a temporary buffer, snprintf() and kstrdup(), just
use kasprintf() that does the same thing in just oneline.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Colin Cross <ccross@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-14 15:53:13 +02:00
Dong Aisheng 02b50ce4cb pinctrl: make pinmux disable function optional
Some SoCs may not have pinmux disable function in HW.

Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-05-15 09:44:50 +02:00
Stephen Warren d4705316c1 pinctrl: add more info to error msgs in pin_request
Additionally print which pin the request failed for, which entity already
claimed it, and what entity was trying to claim it.

Remove duplicate device name from a debug message.

Clean up some indentation.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-05-07 14:44:38 +02:00
John Crispin ad6e1107ba pinctrl: enhance reporting of errors when loading from DT
There are a few places in the api where the code simply returns -EINVAL when
it finds an error. An example is pinmux_map_to_setting() which now reports an
error if we try to match a group with a function that it does not support.

The reporting of errors in pinconf_check_ops and pinmux_check_ops now has the
same style and is located inside the according functions and not the calling
code.

When the map is found in the DT but the default state can not be selected we
get an error to know that the code at least tried.

The patch also removes a stray word from one comment and a "->" from another
for the sake of consistency.

Finally we replace a few pr_err/debug() calls with dev_err/dbg().

Thanks go to Stephen Warren for reviewing the patch and enhancing the reporting
inside pinmux_map_to_setting().

Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-26 23:11:04 +02:00
John Crispin 15f70e1b9a pinctrl: fix signed vs unsigned conditionals inside pinmux_map_to_setting
pinmux_map_to_setting() uses setting->data.mux.func/group to store the return
code of pinmux_func_name_to_selector/pinctrl_get_group_selector(). However,
struct pinctrl_setting_mux defines these elements as unsigned, resulting in all
error codes getting lost. The conditionals following the assignments will always
evaluate to false thus breaking the error paths.

This bug can be triggered by loading a pinmux group map from the devicetree
with an invalid function/group string.

Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-24 15:09:50 +02:00
Dong Aisheng d0bd8df56e pinctrl: show pin name when request pins
Pin name is more useful to users.

Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-18 13:53:13 +02:00
Dong Aisheng ad8bb720c2 pinctrl: add some error checking for user interfaces
This patch can avoid kernel oops in case the mux or config
function is not supported by driver.

Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-18 13:53:11 +02:00
Dong Aisheng a1d31f71e6 pinctrl: fix pinmux_check_ops error checking
Do not use get_functions_count before checking.

Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-18 13:53:11 +02:00
Viresh Kumar d1e90e9e74 pinctrl: replace list_*() with get_*_count()
Most of the SoC drivers implement list_groups() and list_functions()
routines for pinctrl and pinmux. These routines continue returning
zero until the selector argument is greater than total count of
available groups or functions.

This patch replaces these list_*() routines with get_*_count()
routines, which returns the number of available selection for SoC
driver. pinctrl layer will use this value to check the range it can
choose.

This patch fixes all user drivers for this change. There are other
routines in user drivers, which have checks to check validity of
selector passed to them. It is also no more required and hence
removed.

Documentation updated as well.

Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
[Folded in fix and fixed a minor merge artifact manually]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-18 13:53:10 +02:00
Stephen Warren 652162d469 pinctrl: allow concurrent gpio and mux function ownership of pins
Per recent updates to Documentation/gpio.txt, gpiolib drivers should
inform pinctrl when a GPIO is requested. pinctrl then marks that pin as
in-use for that GPIO function.

When an SoC muxes pins in a group, it's quite possible for the group to
contain e.g. 6 pins, but only 4 of them actually be needed by the HW
module that's mux'd to them. In this case, the other 2 pins could be
used as GPIOs. However, pinctrl marks all the pins within the group as
in-use by the selected mux function. To allow the expected gpiolib
interaction, separate the concepts of pin ownership into two parts: One
for the mux function and one for GPIO usage. Finally, allow those two
ownerships to exist in parallel.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-12 22:43:09 +01:00
Stephen Warren ba110d90c0 pinctrl: Show selected function and group in pinmux-pins debugfs
Until recently, the pinctrl pinmux-pins debugfs file displayed the
selected function for each owned pin. This feature was removed during
restructing in support of recent API rework. This change restoreds this
feature, and also displays the group that the function was selected on,
in case a pin is a member of multiple groups.

Based on work by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-05 11:26:01 +01:00
Stephen Warren 1e2082b520 pinctrl: enhance mapping table to support pin config operations
The pinctrl mapping table can now contain entries to:
* Set the mux function of a pin group
* Apply a set of pin config options to a pin or a group

This allows pinctrl_select_state() to apply pin configs settings as well
as mux settings.

v3: Fix find_pinctrl() to iterate over the correct list.
   s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros.
   Fix documentation to use correct mapping table macro.
v2: Added numerous extra PIN_MAP_*() special-case macros.
   Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and
   replace it with pin_get_from_name(). Various minor fixes.
   Updates due to rebase.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-05 11:25:11 +01:00
Stephen Warren 0e3db173e2 pinctrl: add usecount to pins for muxing
Multiple mapping table entries could reference the same pin, and hence
"own" it. This would be unusual now that pinctrl_get() represents a single
state for a client device, but in the future when it represents all known
states for a device, this is quite likely. Implement reference counting
for pin ownership to handle this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-05 11:21:46 +01:00
Stephen Warren 7ecdb16fe6 pinctrl: refactor struct pinctrl handling in core.c vs pinmux.c
This change separates two aspects of struct pinctrl:

a) The data representation of the parsed mapping table, into:

   1) The top-level struct pinctrl object, a single entity returned
      by pinctrl_get().

   2) The parsed version of each mapping table entry, struct
      pinctrl_setting, of which there is one per mapping table entry.

b) The code that handles this; the code for (1) above is in core.c, and
   the code to parse/execute each entry in (2) above is in pinmux.c, while
   the iteration over multiple settings is lifted to core.c.

This will allow the following future changes:

1) pinctrl_get() API rework, so that struct pinctrl represents all states
   for the device, and the device can select between them without calling
   put()/get() again.

2) To support that, a struct pinctrl_state object will be inserted into
   the data model between the struct pinctrl and struct pinctrl_setting.

3) The mapping table will be extended to allow specification of pin config
   settings too. To support this, struct pinctrl_setting will be enhanced
   to store either mux settings or config settings, and functions will be
   added to pinconf.c to parse/execute pin configuration settings.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-05 11:20:50 +01:00
Stephen Warren 57b676f9c1 pinctrl: fix and simplify locking
There are many problems with the current pinctrl locking:

struct pinctrl_dev's gpio_ranges_lock isn't effective;
pinctrl_match_gpio_range() only holds this lock while searching for a gpio
range, but the found range is return and manipulated after releading the
lock. This could allow pinctrl_remove_gpio_range() for that range while it
is in use, and the caller may very well delete the range after removing it,
causing pinctrl code to touch the now-free range object.

Solving this requires the introduction of a higher-level lock, at least
a lock per pin controller, which both gpio range registration and
pinctrl_get()/put() will acquire.

There is missing locking on HW programming; pin controllers may pack the
configuration for different pins/groups/config options/... into one
register, and hence have to read-modify-write the register. This needs to
be protected, but currently isn't. Related, a future change will add a
"complete" op to the pin controller drivers, the idea being that each
state's programming will be programmed into the pinctrl driver followed
by the "complete" call, which may e.g. flush a register cache to HW. For
this to work, it must not be possible to interleave the pinctrl driver
calls for different devices.

As above, solving this requires the introduction of a higher-level lock,
at least a lock per pin controller, which will be held for the duration
of any pinctrl_enable()/disable() call.

However, each pinctrl mapping table entry may affect a different pin
controller if necessary. Hence, with a per-pin-controller lock, almost
any pinctrl API may need to acquire multiple locks, one per controller.
To avoid deadlock, these would need to be acquired in the same order in
all cases. This is extremely difficult to implement in the case of
pinctrl_get(), which doesn't know which pin controllers to lock until it
has parsed the entire mapping table, since it contains somewhat arbitrary
data.

The simplest solution here is to introduce a single lock that covers all
pin controllers at once. This will be acquired by all pinctrl APIs.

This then makes struct pinctrl's mutex irrelevant, since that single lock
will always be held whenever this mutex is currently held.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-05 11:19:49 +01:00
Stephen Warren d4e3198736 pinctrl: enhance pinctrl_get() to handle multiple functions
At present, pinctrl_get() assumes that all matching mapping table entries
have the same "function" value, albeit potentially applied to different
pins/groups.

This change removes this restriction; pinctrl_get() can now handle a set
of mapping tables where different functions are applied to the various
pins/groups.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-02 16:12:03 +01:00
Linus Walleij 1cf94c45ca pinctrl: make the pinmux-pins more helpful
The debugfs file pinmux-pins used to tell which function was
enabled but now states simply which device owns the pin. Being
owned by the pinctrl driver itself means just that it's hogged
so be a bit more helpful by printing that.

ChangeLog v1->v2:
- Preserve the self-referential owner field, just clarify that
  when the pin controller states itself as owner this means
  that it's hogged.

Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-29 19:10:42 +01:00
Stephen Warren 02f5b98951 pinctrl: allocate sizeof(*p) instead of sizeof(struct foo)
This hopefully makes it harder to take the sizeof the wrong type.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-24 06:28:56 +01:00
Stephen Warren 3cc70ed32c pinctrl: record a pin owner, not mux function, when requesting pins
When pins are requested/acquired/got, some device becomes the owner of
their mux setting. At this point, it isn't certain which mux function
will be selected for the pin, since this may vary between each of the
device's states in the pinctrl mapping table. As such, we should record
the owning device, not what we think the initial mux setting will be,
when requesting pins.

This doesn't make a lot of difference right now since pinctrl_get gets
only one single device/state combination, but this will make a difference
when pinctrl_get gets all states, and pinctrl_select_state can switch
between states.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-22 17:59:35 +01:00
Stephen Warren 03665e0f24 pinctrl: Re-order pinmux.[ch] to match each-other
Modify the two files so that the order of function prototypes in the
header matches the order of implementations in the .c file.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-22 17:59:32 +01:00
Stephen Warren 8b9c139f16 pinctrl: use list_add_tail instead of list_add
This mostly makes debugfs files print things in the order that they
were added or acquired, which just feels a little more consistent.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-22 17:59:31 +01:00
Linus Walleij befe5bdfbb pinctrl: factor pin control handles over to the core
This moves the per-devices struct pinctrl handles and device map
over from the pinmux part of the subsystem to the core pinctrl part.
This makes the device handles core infrastructure with the goal of
using these handles also for pin configuration, so that device
drivers (or boards etc) will need one and only one handle to the
pin control core.

Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-10 21:33:06 +01:00
Linus Walleij e93bcee00c pinctrl: move generic functions to the pinctrl_ namespace
Since we want to use the former pinmux handles and mapping tables for
generic control involving both muxing and configuration we begin
refactoring by renaming them from pinmux_* to pinctrl_*.

ChangeLog v1->v2:
- Also rename the PINMUX_* macros in machine.h to PIN_ as indicated
  in the documentation so as to reflect the generic nature of these
  mapping entries from now on.

Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-10 21:33:02 +01:00
Linus Walleij 9dfac4fd7f pinctrl: delete raw device pointers in pinmux maps
After discussion with Mark Brown in an unrelated thread about
ADC lookups, it came to my knowledge that the ability to pass
a struct device * in the regulator consumers is just a
historical artifact, and not really recommended. Since there
are no in-kernel users of these pointers, we just kill them
right now, before someone starts to use them.

Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-01 19:42:35 +01:00
Tony Lindgren b9130b776e pinctrl: add checks for empty function names
This is needed as otherwise we can get the following when
dealing with buggy data in a pinmux driver for
pinmux_search_function:

Unable to handle kernel NULL pointer dereference at virtual
address 00000000
...
PC is at strcmp+0xc/0x34
LR is at pinmux_get+0x350/0x8f4
...

As we need pctldev initialized to call ops->list_functions,
let's initialize it before check_ops calls and pass the
pctldev to the check_ops functions. Do this for both pinmux
and pinconf check_ops functions.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-26 14:13:11 +01:00
Tony Lindgren 9e2551e10b pinctrl: fix pinmux_hog_maps when ctrl_dev_name is not set
The ctrl_dev_name is optional for struct pinmux_map assuming
that ctrl_dev is set. Without this patch we can get:

Unable to handle kernel NULL pointer dereference at virtual
address 00000000
...
(pinmux_hog_maps+0xa4/0x20c)
(pinctrl_register+0x2a4/0x378)
...

Fix this by adding adding a test for map->ctrl_dev.
Additionally move the test for map->ctrl_dev earlier
to optimize out the loop a bit.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-26 14:13:05 +01:00
Tony Lindgren de849eecd0 pinctrl: fix some pinmux typos
Fix some pinmux typos so implementing pinmux drivers
is a bit easier.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-26 14:11:31 +01:00
Uwe Kleine-König f9d41d7cb5 pinctrl: unbreak error messages
It's better to not line break error messages to allow easier grepping
for them even when the line gets >80 chars. Additionally some minor
reformating is done.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-24 22:47:46 +01:00
Chanho Park 706e8520e8 pinctrl: correct a offset while enumerating pins
This patch modifies a offset while enumerating pins to support a
partial pin space. If we use a pin number for enumerating pins,
the pin space always starts with zero base. Indeed, we always check
the pin is in the pin space. An extreme example, there is only two pins.
One is 0. Another is 1000. We always enumerate whole offsets until 1000.
For solving this problem, we use the offset of the pin array instead
of the zero-based pin number.

Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[Restored sparse pin space comment]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:10:09 +01:00
Dong Aisheng e6337c3c96 pinctrl: some typo fixes
Minor copyedits.

Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:10:08 +01:00
Stephen Warren 51cd24ee62 pinctrl: don't create a device for each pin controller
Pin controllers should already be instantiated as a device, so there's
no need for the pinctrl core to create a new struct device for each
controller.

This allows the controller's real name to be used in the mux mapping
table, rather than e.g. "pinctrl.0", "pinctrl.1", etc.

This necessitates removal of the PINMUX_MAP_PRIMARY*() macros, since
their sole purpose was to hard-code the .ctrl_dev_name field to be
"pinctrl.0".

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:10:06 +01:00
Linus Walleij 59b099b049 pinctrl: make it possible to add multiple maps
Since we now anyway make a copy of the platform-supplied pinmux
map, we can just as well make it possible to call the function
adding maps several times, so as to simplify cases (as PXA) where
several sets of disparate mappings need to be added depending on
target platform.

Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Arnd Bergmann <arnd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:10:02 +01:00
Linus Walleij 97607d157c pinctrl: make a copy of pinmux map
This makes a deep copy of the pinmux function map instead of
keeping the copy supplied from the platform around. This makes
it possible to tag the platforms map with __initdata as is also
done as part of this patch.

Rationale: a certain target platform (PXA) has numerous
pinmux maps, many of which will be lying around unused after
boot in a multi-platform binary. Instead, deep-copy the one
we're going to use and tag them all __initdata so they go away
after boot.

ChangeLog v1->v2:
- Fixup the deep copy, missed a few items on the struct,
  plus mark bool member non-const since we're making runtime
  copies if this stuff now.
ChangeLog v2->v3:
- Make a shallow copy (just copy the array of map structs)
  as Arnd noticed, string constants never get discarded by the
  kernel anyway, so these pointers may be safely copied over.

Reviewed-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:10:02 +01:00
Linus Walleij 542e704f3f pinctrl: GPIO direction support for muxing
When requesting a single GPIO pin to be muxed in, some controllers
will need to poke a different value into the control register
depending on whether the pin will be used for GPIO output or GPIO
input. So create pinmux counterparts to gpio_direction_[input|output]
in the pinctrl framework.

ChangeLog v1->v2:
- This also amends the documentation to make it clear the this
  function and associated machinery is *ONLY* intended as a backend
  to gpiolib machinery, not for everyone and his dog to start playing
  around with pins.
ChangeLog v2->v3:
- Don't pass an argument to the common request function, instead
  provide pinmux_* counterparts to the gpio_direction_[input|output]
  calls, simpler and anyone can understand it.
ChangeLog v3->v4:
- Fix numerous spelling mistakes and dangling text in documentation.
  Add Ack and Rewewed-by.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:10:01 +01:00
Chanho Park 3c739ad0df pinctrl: add a pin_base for sparse gpio-ranges
This patch enables mapping a base offset of gpio ranges with
a pin offset even if does'nt matched. A base of pinctrl_gpio_range
means a base offset of gpio. However, we cannot convert gpio to pin
number for sparse gpio ranges just only using a gpio base offset.
We can convert a gpio to real pin number(even if not matched) using
a new pin_base which means a base pin offset of requested gpio range.
Now, the pin control subsystem passes the pin base offset to the
pinmux driver.

For example, let's assume below two gpio ranges in the system.

static struct pinctrl_gpio_range gpio_range_a = {
    .name = "chip a",
    .id = 0,
    .base = 32,
    .pin_base = 32,
    .npins = 16,
    .gc = &chip_a;
};

static struct pinctrl_gpio_range gpio_range_b = {
    .name = "chip b",
    .id = 0,
    .base = 48,
    .pin_base = 64,
    .npins = 8,
    .gc = &chip_b;
};

We can calucalate a exact pin ranges even if doesn't matched with gpio ranges.

chip a:
    gpio-range : [32 .. 47]
    pin-range  : [32 .. 47]
chip b:
    gpio-range : [48 .. 55]
    pin-range  : [64 .. 71]

Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:10:01 +01:00
Linus Walleij 336cdba09a pinctrl: documentation update
Update the docs removing an obsolete __refdata tag and document
the mysterious return value of pin_free(). And fixes up some various
confusions in the pinctrl documentation.

Reported-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Reported-by: Thomas Abraham <thomas.abraham@linaro.org>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:10:00 +01:00
Stephen Warren 3712a3c488 pinctrl: add explicit gpio_disable_free pinmux_op
Some pinctrl drivers (Tegra at least) program a pin to be a GPIO in a
completely different manner than they select which function to mux out of
that pin. In order to support a single "free" pinmux_op, the driver would
need to maintain a per-pin state of requested-for-gpio vs. requested-for-
function. However, that's a lot of work when the core already has explicit
separate paths for gpio request/free and function request/free.

So, add a gpio_disable_free op to struct pinmux_ops, and make pin_free()
call it when appropriate.

When doing this, I noticed that when calling pin_request():

    !!gpio == (gpio_range != NULL)

... and so I collapsed those two parameters in both pin_request(), and
when adding writing the new code in pin_free().

Also, for pin_free():

    !!free_func == (gpio_range != NULL)

However, I didn't want pin_free() to know about the GPIO function naming
special case, so instead, I reworked pin_free() to always return the pin's
previously requested function, and now pinmux_free_gpio() calls
kfree(function). This is much more balanced with the allocation having
been performed in pinmux_request_gpio().

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:09:59 +01:00
Marek Belisko d2f6a1c6fb pinctrl: remove double pin validity check.
Function pin_is_valid just call pin_desc_get which is in pin_request
call some line below. Remove pin_is_valid() check.

Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:09:59 +01:00
Linus Walleij 7afde8baa8 pinctrl: move group lookup to core
Now also the core needs to look up pin groups so move the lookup
function there and expose it in the internal header.

Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 09:09:58 +01:00
Uwe Kleine-König cc96ffbb74 pinctrl: remove two unused global variables
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-08 16:18:30 +01:00
Stephen Warren 5d2eaf8090 pinctrl: Don't copy function name when requesting a pin
Instead, store a pointer to the currently assigned function.

This allows us to delete the mux_requested variable from pin_desc; a pin
is requested if its currently assigned function is non-NULL.

When a pin is requested as a GPIO rather than a regular function, the
assigned function name is dynamically constructed. In this case, we have
to kstrdup() the dynamically constructed name, so that mux_function doesn't
pointed at stack data. This requires pin_free to be told whether to free
the mux_function pointer or not.

This removes the hard-coded maximum function name length.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 11:50:07 +02:00
Stephen Warren a5818a8bd0 pinctrl: get_group_pins() const fixes
get_group_pins() "returns" a pointer to an array of const objects, through
a pointer parameter. Fix the prototype so what's pointed at by the returned
pointer is const, rather than the function parameter being const.

This also allows the removal of a cast in each of the two current pinmux
drivers.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 11:41:49 +02:00