Commit Graph

31 Commits

Author SHA1 Message Date
Pratyush Anand 58a0f23fdd USB: DWC3: Issue device soft reset before core soft reset
Synopsys specification clearly states under section "Device Power-On or
Soft Reset" that DCTL.CSftRst=1 should be first step.  So, just follow
what specification says.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-06-22 13:22:46 +03:00
Pratyush Anand 45627ac6a4 USB: DWC3: Put 100 ms delay for phy to be stable
Before taking core out of reset phy must be stable. So wait for 100ms
after clear phy reset.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-06-22 13:21:54 +03:00
Paul Zimmerman 7acd85e0eb usb: dwc3: core: make sure evt->lpos is correctly initialized
The same event buffers will be reused when coming
out of hibernation, so we must reinitialize them
properly to avoid any mistakes.

While at that, also take dwc3_event_buffers_setup()
out of __devinit section.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-06-03 23:08:24 +03:00
Greg Kroah-Hartman 23063b378d usb: dwc3: patches for v3.5 merge window
This pull request contains one workaround for a Silicon
 Issue found on all RTL releases prior to 2.20a, which
 would cause a metastability state on Run/Stop bit.
 
 We also have some patches implementing a few extra Standard
 requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
 as well as one patch, which has been pending for a long time,
 implementing LPM support.
 
 Last, but not least, we are splitting the host address space
 out of the dwc3 core driver otherwise xHCI won't be able to
 request_mem_region() its own address space. This patch is
 only needed because we are (as we should) re-using the xHCI
 driver, which is a completely separate module.
 
 Together with these three big changes, come a few extra preparatory
 patches which most move code around, define macros and so on, as
 well as a fix for Isochronous transfers which hasn't been triggered
 before.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJPo7lXAAoJEIaOsuA1yqRESaIP/AgxZIfOAUbPx0GWLnhub3qr
 SxaUplweFc9q4KXRLn0kGdY9QArPR3bqW9g8KOTiRCBYRtjpACyMjibAUaAht81h
 +vLdPt87Slj2c14t1uguWFvgCUYQOCugkVvDIjRg9PCLIuTahm4cIBFqL3RJOHFf
 9WCd8JjH9ahr85ZtoCBk9B5bDNn71nS+Yh6/8+Ab90AE4vZ6t8Xx3+wLTHy2CBYQ
 UH1o61QZreAJ0J3OiUobjqrVbYwz6TM0dFYMjA6ko+OiPRhVOj8/C8aNl/U1whRm
 +7jjJiWO9aHp+Tu2OAQOBF6ydc3ZLBEiCl9RiE+O9MppmtOykzkTHFm1ZXatCEY7
 UUYOy43VXLNlHoz8nidNw6P25hAwwlSijzlyawpihKbIaE8le2MpE6I00AlciM2q
 BEo4LpluC8Rr6CUUr5W9dPZUexRlzxdAL5nQSJUnJgfEPphpP3x7dWTxUZBaWjq6
 akqjgGqVj1QKwMnqL4GILtRgdqWj6WYrw67fYVLHqj8QQla4cgXQ2sHp9/R0imvT
 nmjiL5ZiuIWWr965DgVHZwqIkdvMpSQb99a1xmptw8lFDGkVJDCssPDdEErbBMwy
 KmOSaqKeg/Yway05i+Pwo/NUKHQSZeiyuguzniMrF7iYFF1/2hVYRgfpH4V+95w/
 Xrnz4uH2YJGQGPddf87P
 =qgf/
 -----END PGP SIGNATURE-----

Merge tag 'dwc3-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

usb: dwc3: patches for v3.5 merge window

This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.

We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.

Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.

Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.

[ resolved conflicts and build error in drivers/usb/dwc3/gadget.c - gregkh]
2012-05-07 10:09:55 -07:00
Ido Shayevitz 51249dca62 usb: dwc3: core: split host address space
This fix prevents a problem with dwc3 and host mode where
we were requesting the entire memory region in dwc3/core.c,
thus preventing xhci-plat from ever ioremapping its own address space.

Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-04-24 15:37:04 +03:00
Anton Tikhomirov 64b6c8a701 usb: dwc3: Free event buffers array
Array should be freed together with event buffers, since it was
allocated dynamically.

Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-04-10 19:11:46 +03:00
Tobias Klauser b1116dcc63 usb: dwc3: core: Convert to module_platform_driver
Use the module_platform_driver macro.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-02 16:20:28 -08:00
Paul Zimmerman 3e87c42a29 usb: dwc3: replace hard-coded constant in DWC3_GCTL_SCALEDOWN(3)
Define DWC3_GCTL_SCALEDOWN_MASK and use it in place of
DWC3_GCTL_SCALEDOWN(3).

Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-03-02 12:12:06 +02:00
Dan Carpenter 075cd14d2a usb: dwc3: make dwc3_get_device_id() return the id
We always return zero instead of the id we found.

Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-03-02 12:12:02 +02:00
Paul Zimmerman 1d04679395 usb: dwc3: clean up whitespace damage, typos, missing parens, etc.
trivial patch, no functional changes

Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-03-02 12:12:01 +02:00
Danny Kukawka 2cd0e85121 usb: dwc3: linux/module.h included twice
drivers/usb/dwc3/core.c and drivers/usb/dwc3/dwc3-omap.c
included 'linux/module.h' twice, remove the duplicates.

Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-03-02 12:12:00 +02:00
Chanho Park 802ca85067 usb: dwc3: use devm_xxx functions
This patch enables to use devm_xxx functions during probing driver.
The devm_xxx series functions are able to release resource when the
driver is detatched. We can remove several codes to release resources
in the probe function.

Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-03-02 12:11:59 +02:00
Felipe Balbi 457e84b662 usb: dwc3: gadget: dynamically re-size TxFifos
We need to dynamically re-size TxFifos for the
cases where default values will not do.

While at that, we create a simple function which,
for now, will just allocate one full packet fifo
space for each of the enabled endpoints.

This can be improved later in order to allow for
better throughput by allocating more space for
endpoints which could make good use of that like
isochronous and bulk.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-02-06 11:48:34 +02:00
Linus Torvalds 55b81e6f27 Merge branch 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (232 commits)
  USB: Add USB-ID for Multiplex RC serial adapter to cp210x.c
  xhci: Clean up 32-bit build warnings.
  USB: update documentation for usbmon
  usb: usb-storage doesn't support dynamic id currently, the patch disables the feature to fix an oops
  drivers/usb/class/cdc-acm.c: clear dangling pointer
  drivers/usb/dwc3/dwc3-pci.c: introduce missing kfree
  drivers/usb/host/isp1760-if.c: introduce missing kfree
  usb: option: add ZD Incorporated HSPA modem
  usb: ch9: fix up MaxStreams helper
  USB: usb-skeleton.c: cleanup open_count
  USB: usb-skeleton.c: fix open/disconnect race
  xhci: Properly handle COMP_2ND_BW_ERR
  USB: remove dead code from suspend/resume path
  USB: add quirk for another camera
  drivers: usb: wusbcore: Fix dependency for USB_WUSB
  xhci: Better debugging for critical host errors.
  xhci: Be less verbose during URB cancellation.
  xhci: Remove debugging about ring structure allocation.
  xhci: Remove debugging about toggling cycle bits.
  xhci: Remove debugging for individual transfers.
  ...
2012-01-09 12:09:47 -08:00
Felipe Balbi 248b122b13 usb: dwc3: core: fix cached revision on our structure
All our revision macros are defined with the entire
32-bits which we read from GSNPSID register, so we
must cache all 32-bits properly rather than masking
the top 16-bits.

This will fix all revision checks we have on current
driver.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-14 21:59:30 +02:00
Sebastian Andrzej Siewior 164d773168 usb: dwc3: use correct hwparam register for power mgm check
We mask the correct bits within the wrong register. The power
optimization mode is stored hwparam1 register and not in hwparam0.

Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:48:44 +02:00
Sebastian Andrzej Siewior 4878a02898 usb: dwc3: move generic dwc3 code from gadget into core
A few inits like the scale value or the removal of the DISSCRAMBLE is
done in the gadget code however it touches a general register.
Move this piece to the core.c file since it is likely to be requied by
both, parts of the core (device and host).

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:48:27 +02:00
Sebastian Andrzej Siewior 3140e8cbfe usb: dwc3: use a helper function for operation mode setting
There are two where need to set operational mode:
- during initialization while we decide to run in host,device or DRD
  mode
- at runtime via the debugfs interface.

This patch provides a new function which sets the operational mode and
moves its initialiation to the mode switch instead in the gadget code
itself.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:48:26 +02:00
Felipe Balbi 457d3f214f usb: dwc3: core: drop DWC3_EVENT_BUFFERS_MAX
hardware will tell us how many event buffers we
need to support, so let's allocate the array
dynamically too.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:48:24 +02:00
Felipe Balbi 8300dd236e usb: dwc3: move dwc3 device ID bitmap to core.c
if we want to support situations where we have
both SoC and PCIe versions of the IP on the same
platform, we need to have sequential numbers between
them, otherwise we will still have name collisions.

Because of that, we need to move dwc3_get/put_device_id()
to core.c and export that symbol to be used by glue
layers.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:48:21 +02:00
Sebastian Andrzej Siewior 7ae4fc4dc8 usb: dwc3: add a platform device alias
We can have three modules here: dwc3.ko, dwc3-omap.ko and dwc3-pci.ko.
The later have already ids-aliases for probing and is fine. The omap
module has alias for DT but lacks alias for the "native"
platform_device. Maybe we should get rid of it and stick to the DT name?
Both glue modules create a new device for which the dwc3.ko module is
responsible and that one lacks the platform alias.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:48:17 +02:00
Felipe Balbi d07e8819a0 usb: dwc3: add xHCI Host support
The Designware USB3 IP can be configured with
an internal xHCI. If we're running on such a
version, let's start the xHCI stack.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:48:12 +02:00
Felipe Balbi 0949e99b05 usb: dwc3: fetch mode of operation from HW
There's no need to add driver_data for something
we can fetch from HW.

This also makes our id_table unnecessary - at least
for now -, so we also remove it on the same patch.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:48:11 +02:00
Felipe Balbi 9f622b2a40 usb: dwc3: calculate number of event buffers dynamically
This will allow us to only allocate memory when
we actually need.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:48:11 +02:00
Felipe Balbi 6c167fc9b0 usb: dwc3: allow forcing a maximum speed
this is mainly for testing. In order to be able
to test if we're enumerating correctly on all
speeds, let that be controlled by a module
parameter.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:48:10 +02:00
Paul Gortmaker 2204fdee84 usb: Add module.h to various dwc3 drivers
These files uses the full set of MODULE_ macros and so need to
include module.h directly.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-10-04 10:27:28 -07:00
Felipe Balbi 26ceca9750 usb: dwc3: core: cache GHWPARAMS* registers
cache the contents of GHWPARAMS* registers in
our device structure for easy access.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-10-04 10:25:55 -07:00
Sebastian Andrzej Siewior 49a25cc9a7 usb: dwc: remove "All rights reserved" statement.
Some people think that this line is not compatible with the GPL. The
statement was required due to the Buenos Aires Convention and is now
deprecated. I remove it because it is said that it is pointless nowdays.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-10-04 10:25:52 -07:00
Felipe Balbi a72e658bcd usb: dwc3: add module.h to dwc3-omap.c and core.c
We need that header because of THIS_MODULE.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-09-09 13:03:00 +03:00
Sebastian Andrzej Siewior 7650bd74d3 usb: dwc3: core: move the core check before soft reset
We read the DWC3_GSNPSID register to make sure we got the correct
register offset passed. One of the recent commits moved the soft reset
before this so in case of the wrong offset we end up with "reset timed
out". This patch moves the "id" check before the reset again.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-09-09 13:02:09 +03:00
Felipe Balbi 72246da40f usb: Introduce DesignWare USB3 DRD Driver
The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.

Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.

The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.

More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.

While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.

[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 16:03:11 -07:00