The HD-audio codec driver remove may happen also at dynamically
unbinding during operation, hence it needs manual triggers of
snd_device_disconnect() calls, while it's missing for the jack objects
that are associated with the codec.
This patch adds the manual disconnection call for jacks when the
remove happens without card->shutdown (i.e. not under the full
removal).
Link: https://lore.kernel.org/r/20211117133040.20272-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec is unbound dynamically via sysfs while its stream is in
use, we may face a potential deadlock at the proc remove or a UAF.
This happens since the hda_pcm is managed by a linked list, as it
handles the hda_pcm object release via kref.
When a PCM is opened at the unbinding time, the release of hda_pcm
gets delayed and it ends up with the close of the PCM stream releasing
the associated hda_pcm object of its own. The hda_pcm destructor
contains the PCM device release that includes the removal of procfs
entries. And, this removal has the sync of the close of all in-use
files -- which would never finish because it's called from the PCM
file descriptor itself, i.e. it's trying to shoot its foot.
For addressing the deadlock above, this patch changes the way to
manage and release the hda_pcm object. The kref of hda_pcm is
dropped, and instead a simple refcount is introduced in hda_codec for
keeping the track of the active PCM streams, and at each PCM open and
close, this refcount is adjusted accordingly. At unbinding, the
driver calls snd_device_disconnect() for each PCM stream, then
synchronizes with the refcount finish, and finally releases the object
resources.
Fixes: bbbc7e8502 ("ALSA: hda - Allocate hda_pcm objects dynamically")
Link: https://lore.kernel.org/r/20211116072459.18930-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that a few recent AMD systems show the codec configuration
errors at the early boot, while loading the driver at a later stage
works magically. Although the root cause of the error isn't clear,
it's certainly not bad to allow retrying the codec probe in such a
case if that helps.
This patch adds the capability for retrying the probe upon codec probe
errors on the certain AMD platforms. The probe_work is changed to a
delayed work, and at the secondary call, it'll jump to the codec
probing.
Note that, not only adding the re-probing, this includes the behavior
changes in the codec configuration function. Namely,
snd_hda_codec_configure() won't unregister the codec at errors any
longer. Instead, its caller, azx_codec_configure() unregisters the
codecs with the probe failures *if* any codec has been successfully
configured. If all codec probe failed, it doesn't unregister but let
it re-probed -- which is the most case we're seeing and this patch
tries to improve.
Even if the driver doesn't re-probe or give up, it will go to the
"free-all" error path, hence the leftover codecs shall be disabled /
deleted in anyway.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190801
Link: https://lore.kernel.org/r/20211006141940.2897-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far we have a few workarounds at shutdown for each codec,
e.g. turning off the display power and setting the codec to D3.
But all those are basically a part of the suspend procedure.
Moreover, the streams are still active after that call, hence it might
hit the update on the codec that has been already put to D3.
In this patch, instead of calling each reboot_notify callback, simply
put the codec into the runtime-suspended state after the manual
suspend of all PCM streams. It makes the code and the behavior more
consistent.
The reboot_notify callback is no longer used after this patch, and
will be cleaned up later.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214045
Link: https://lore.kernel.org/r/20210813081230.4268-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When HD-audio bus receives unsolicited events during its system
suspend/resume (S3 and S4) phase, the controller driver may still try
to process events although the codec chips are already (or yet)
powered down. This might screw up the codec communication, resulting
in CORB/RIRB errors. Such events should be rather skipped, as the
codec chip status such as the jack status will be fully refreshed at
the system resume time.
Since we're tracking the system suspend/resume state in codec
power.power_state field, let's add the check in the common unsol event
handler entry point to filter out such events.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182377
Tested-by: Abhishek Sahu <abhsahu@nvidia.com>
Cc: <stable@vger.kernel.org> # 183ab39eb0ea: ALSA: hda: Initialize power_state
Link: https://lore.kernel.org/r/20210310112809.9215-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is an alternative fix attemp for the issue reported in the commit
caa8422d01 ("ALSA: hda: Flush interrupts on disabling") that was
reverted later due to regressions. Instead of tweaking the hardware
disablement order and the enforced irq flushing, do calling
cancel_work_sync() of the unsol work early enough, and explicitly
ignore the unsol events during the shutdown by checking the
bus->shutdown flag.
Fixes: caa8422d01 ("ALSA: hda: Flush interrupts on disabling")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://lore.kernel.org/r/s5h1ruxt9cz.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current code, the codec registration may happen both at the
codec bind time and the end of the controller probe time. In a rare
occasion, they race with each other, leading to Oops due to the still
uninitialized card device.
This patch introduces a simple flag to prevent the codec registration
at the codec bind time as long as the controller probe is going on.
The controller probe invokes snd_card_register() that does the whole
registration task, and we don't need to register each piece
beforehand.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a kernel module which is used by the legacy HDA
codec drivers as library. This implements hdac_ext_bus_ops to enable
the reuse of legacy HDA codec drivers with ASoC platform drivers.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As suggested by Takashi, move this header file to make it easier
to include from e.g. the Intel Skylake driver in follow-up patches
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When hda_codec_driver_probe meet error and return failure, we need
to free resource with patch_ops.free, or we will get resource leak.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the generic codec driver is specified via model option or such,
the hda driver doesn't try to load the generic driver module but still
loads the codec-specific driver, and this ends up with the binding
failure.
This patch fixes it by moving the generic module request in the common
helper code.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111021
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally we have a proper infrastructure to generate the modaliases
automatically, let's move to hda_device_id from the legacy
hda_codec_preset that contains basically the same information.
The patch function hook is stored in driver_data field, which is long,
and we need an explicit cast. Other than that, the conversion is
mostly straightforward. Each entry is even simplified using a macro,
and the lengthy (and error-prone) manual modaliases got removed.
As a result, we achieved a quite good diet:
14 files changed, 407 insertions(+), 595 deletions(-)
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent commit [7fbe824a0f0e: ALSA: hda - Update mixer name for the
lower codec address] tried to improve the mixer chip name assignment
in the order of codec address. However, this fix was utterly bogus;
it checks the field set in each codec, thus this value is reset at
each codec creation, of course. For really handling this priority,
the assignment has to be remembered in the common place, namely in
hda_bus, instead of hda_codec.
Fixes: 7fbe824a0f ('ALSA: hda - Update mixer name for the lower codec address')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In most cases, we prefer the onboard codec as the primary device, thus
it's better to set it as the mixer name. Currently, however, the
mixer name is updated per the device instantiation order, and user
gets often HDMI/DP or other seen as a mixer chip name. Also, if a
codec name is renamed by the driver, the old chip name might be left
still as the mixer name.
This patch addresses these issues by remembering the chip address that
was referred as the mixer name. When a codec with the same or lower
address gives its name, renew the mixer name accordingly, as it's
either the update of the codec name or we get likely the more
appropriate chip as the reference.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few multiple codec drivers do renaming the chip_name string but all
these are open-coded and some of them have even no error check. Let's
make common helpers to do it properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds an infrastructure to support regmap-based verb
accesses. Because o the asymmetric nature of HD-audio verbs,
especially the amp verbs, we need to translate the verbs as a sort of
pseudo registers to be mapped uniquely in regmap.
In this patch, a pseudo register is built from the NID, the
AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent
to HD-audio bus but without codec address field. OTOH, for writing,
the same pseudo register is translated to AC_VERB_SET_* automatically.
The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding
AC_VERB_GET_AMP_* verb and parameter at writing.
Some verbs has a single command for read but multiple for writes. A
write for such a verb is split automatically to multiple verbs.
The patch provides also a few handy helper functions. They are
designed to be accessible even without regmap. When no regmap is set
up (e.g. before the codec device instantiation), the direct hardware
access is used. Also, it tries to avoid the unnecessary power-up.
The power up/down sequence is performed only on demand.
The codec driver needs to call snd_hdac_regmap_exit() and
snd_hdac_regmap_exit() at probe and remove if it wants the regmap
access.
There is one flag added to hdac_device. When the flag lazy_cache is
set, regmap helper ignores a write for a suspended device and returns
as if it was actually written. It reduces the hardware access pretty
much, e.g. when adjusting the mixer volume while in idle. This
assumes that the driver will sync the cache later at resume properly,
so use it carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the driver is unloaded before the codec is bound, it still keeps
the runtime PM refcount up, and results in the unbalance. This patch
covers these cases by introducing a flag indicating the runtime PM
initialization and handling the codec registration procedure more
properly. It also fixes the missing input beep device as a gratis,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the sysfs files assigned to the codec device on the
bus which were formerly identical with hwdep sysfs files. Now it
shows only a few core parameter, vendor_id, subsystem_id, revision_id,
afg, mfg, vendor_name and chip_name.
In addition, now a widget tree is added to the bus device sysfs
directory for showing the widget topology and attributes. It's just a
flat tree consisting of subdirectories named as the widget NID
including various attributes like widget capability bits. The AFG
(usually NID 0x01) is always found there, and it contains always
amp_in_caps, amp_out_caps and power_caps files. Each of these
attributes show a single value. The rest are the widget nodes
belonging to that AFG. Note that the child node might not start from
0x02 but from another value like 0x0a.
Each child node may contain caps, pin_caps, amp_in_caps, amp_out_caps,
power_caps and connections files. The caps (representing the widget
capability bits) always contain a value. The rest may contain
value(s) if the attribute exists on the node. Only connections file
show multiple values while other attributes have zero or one single
value.
An example of ls -R output is like below:
% ls -R /sys/bus/hdaudio/devices/hdaudioC0D0/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/:
01/ 04/ 07/ 0a/ 0d/ 10/ 13/ 16/ 19/ 1c/ 1f/ 22/
02/ 05/ 08/ 0b/ 0e/ 11/ 14/ 17/ 1a/ 1d/ 20/ 23/
03/ 06/ 09/ 0c/ 0f/ 12/ 15/ 18/ 1b/ 1e/ 21/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/01:
amp_in_caps amp_out_caps power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/02:
amp_in_caps amp_out_caps caps connections pin_caps pin_cfg
power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/03:
.....
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now some codes and functionalities of hda_codec struct are moved to
hdac_device struct. A few basic attributes like the codec address,
vendor ID number, FG numbers, etc are moved to hdac_device, and they
are accessed like codec->core.addr. The basic verb exec functions are
moved, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few basic codes for communicating over HD-audio bus are moved to
struct hdac_bus now. It has only command and get_response ops in
addition to the unsolicited event handling.
Note that the codec-side tracing support is disabled temporarily
during this transition due to the code shuffling. It will be
re-enabled later once when all pieces are settled down.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Define the common hd-audio driver and device types to bind over
snd_hda_bus_type publicly. This allows to implement other type of
device and driver code over hd-audio bus.
Now both struct hda_codec and struct hda_codec_driver inherit these
new struct hdac_device and struct hdac_driver, respectively.
The bus registration is done in subsys_initcall() to assure it
before any other driver registrations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver shutdown ops is simpler than registering reboot notifier
manually. There should be no functional change by this -- the codec
driver calls its own callback while the bus driver just calls
azx_stop() like before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes the code flow easier -- instead of the controller driver
calling snd_hda_build_pcms() and snd_hda_build_controls() explicitly,
the codec driver itself builds PCMs and controls at probe time. Then
the controller driver only needs to call snd_card_register().
Also, this allows us the full bind/unbind control, too. Even when a
codec driver is bound later, it automatically registers the new PCM
and controls by itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we have all pieces ready, and put them into places:
- add the hda_pcm refcount to azx_pcm_open() and azx_pcm_close(),
- call the most of cleanup code in hda_codec_reset() from the codec
driver remove,
- call the same code also from the hda_codec object free.
Then the codec driver can be unbound more safely now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the codec object to have an individual card pointer. Not only
this simplifies the redirections in many places, also this will allow
us to make each codec assigned to a different card object.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch moves the suspend/resume mechanisms down to each codec
driver level, as we have a proper codec driver bound on the bus now.
Then we get the asynchronous PM gratis without fiddling much in the
driver level.
As a soft-landing transition, implement the common suspend/resume pm
ops for hda_codec_driver and keep the each codec driver intact. Only
the callers of suspend/resume in the controller side (azx_suspend()
and azx_resume()) are removed.
Another involved place is azx_bus_reset() calling the temporary
suspend and resume as a hackish method of bus reset. The HD-audio
core provide a helper function snd_hda_bus_reset() instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we create the standard HD-audio bus (/sys/bus/hdaudio), and bind
the codec driver with the codec device over there. This is the first
step of the whole transition so that the changes to each codec driver
are kept as minimal as possible.
Each codec driver needs to register hda_codec_driver struct containing
the currently existing preset via the new helper macro
module_hda_codec_driver(). The old hda_codec_preset_list is replaced
with this infrastructure. The generic parsers (for HDMI and other)
are also included in the preset with the special IDs to bind
uniquely.
In HD-audio core side, the device binding code is split to
hda_bind.c. It provides the snd_hda_bus_type implementation to match
the codec driver with the given codec vendor ID. It also manages the
module auto-loading by itself like before: when the matching isn't
found, it tries to probe the corresponding codec modules, and finally
falls back to the generic drivers. (The special ID mentioned above is
set at this stage.)
The only visible change to outside is that the hdaudio sysfs entry now
appears in /sys/bus/devices, not as a sound class device.
More works to move the suspend/resume and remove ops will be
(hopefully) done in later patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai