Pull m68knommu fix from Greg Ungerer:
"A single fix for compilation breakage to many of the ColdFire CPU
targets"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: only use local gpio_request_one if not using GPIOLIB
Pull m68k fix from Geert Uytterhoeven:
"A boot lock-up on Mac, also destined for stable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/mac: Fix unexpected interrupt with CONFIG_EARLY_PRINTK
The present code does not wait for the SCC to finish resetting itself
before trying to initialise the device. The result is that the SCC
interrupt sources become enabled (if they weren't already). This leads to
an early boot crash (unexpected interrupt) given CONFIG_EARLY_PRINTK. Fix
this by adding a delay. A successful reset disables the interrupt sources.
Also, after the reset for channel A setup, the SCC then gets a second
reset for channel B setup which leaves channel A uninitialised again. Fix
this by performing the reset only once.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: stable@vger.kernel.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Compiling for targets that use the local gpio code (not GPIOLIB) fail to
compile with:
CC arch/m68k/platform/coldfire/device.o
In file included from include/linux/gpio.h:45:0,
from arch/m68k/platform/coldfire/device.c:15:
/home/gerg/new-wave.git/linux-3.x/arch/m68k/include/asm/gpio.h:89:19: error: static declaration of ‘gpio_request_one’ follows non-static declaration
include/asm-generic/gpio.h:195:12: note: previous declaration of ‘gpio_request_one’ was here
Fix by conditionally using the local gpio_request_one() function based on
!CONFIG_GPIOLIB.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Linux/M68K currently doesn't support robust futexes or PI mutexes.
The problem is that the futex code needs to perform certain ops
(cmpxchg, set, add, or, andn, xor) atomically on user-space
addresses, and M68K's lack of a futex.h causes those operations
to be unsupported and disabled.
This patch adds that support, but only for uniprocessor machines,
which is adequate for M68K. For UP it's enough to disable preemption
to ensure mutual exclusion (futexes don't need to care about other
hardware agents), and the mandatory pagefault_disable() does just that.
This patch is closely based on the one I co-wrote for UP ARM back
in August 2008. The main change is that this patch uses the C
get_user/put_user accessors instead of inline assembly code with
exception table fixups.
For non-MMU machines the new futex.h simply redirects to the generic
futex.h, so there is no functional change for them.
Tested on aranym with the glibc-2.17 test suite: no regressions, and
a number of mutex/condvar test cases went from failing to succeeding
(tst-mutexpi{5,5a,6,9}, tst-cond2[45], tst-robust[1-9], tst-robustpi[1-8]).
Also tested with glibc-2.18 HEAD and a local glibc patch to enable PI
mutexes: no regressions.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Andreas Schwab <schwab@linux-m68k.org>
[geert: Added removal of ""generic-y += futex.h"]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
- Two krealloc() abuse fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iEYEABECAAYFAlGLydsACgkQdwG7hYl686O3ZwCfYIJUdE/VADo53j3SwDbCEa15
pMgAnA13t6dKgC74Xqk5dd65KKaw64WB
=nbL9
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130509' of git://git.infradead.org/~dwmw2/random-2.6
Pull misc fixes from David Woodhouse:
"This is some miscellaneous cleanups that don't really belong anywhere
else (or were ignored), that have been sitting in linux-next for some
time. Two of them are fixes resulting from my audit of krealloc()
usage that don't seem to have elicited any response when I posted
them, and the other three are patches from Artem removing dead code."
* tag 'for-linus-20130509' of git://git.infradead.org/~dwmw2/random-2.6:
pcmcia: remove RPX board stuff
m68k: remove rpxlite stuff
pcmcia: remove Motorola MBX860 support
params: Fix potential memory leak in add_sysfs_param()
dell-laptop: Fix krealloc() misuse in parse_da_table()
Pull m68knommu updates from Greg Ungerer:
"The bulk of the changes are generalizing the ColdFire v3 core support
and adding in 537x CPU support. Also a couple of other bug fixes, one
to fix a reintroduction of a past bug in the romfs filesystem nommu
support."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: enable Timer on coldfire 532x
m68knommu: fix ColdFire 5373/5329 QSPI base address
m68knommu: add support for configuring a Freescale M5373EVB board
m68knommu: add support for the ColdFire 537x family of CPUs
m68knommu: make ColdFire M532x platform support more v3 generic
m68knommu: create and use a common M53xx ColdFire class of CPUs
m68k: remove unused asm/dbg.h
m68k: Set ColdFire ACR1 cache mode depending on kernel configuration
romfs: fix nommu map length to keep inside filesystem
m68k: clean up unused "config ROMVECSIZE"
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
Pull compat cleanup from Al Viro:
"Mostly about syscall wrappers this time; there will be another pile
with patches in the same general area from various people, but I'd
rather push those after both that and vfs.git pile are in."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
syscalls.h: slightly reduce the jungles of macros
get rid of union semop in sys_semctl(2) arguments
make do_mremap() static
sparc: no need to sign-extend in sync_file_range() wrapper
ppc compat wrappers for add_key(2) and request_key(2) are pointless
x86: trim sys_ia32.h
x86: sys32_kill and sys32_mprotect are pointless
get rid of compat_sys_semctl() and friends in case of ARCH_WANT_OLD_COMPAT_IPC
merge compat sys_ipc instances
consolidate compat lookup_dcookie()
convert vmsplice to COMPAT_SYSCALL_DEFINE
switch getrusage() to COMPAT_SYSCALL_DEFINE
switch epoll_pwait to COMPAT_SYSCALL_DEFINE
convert sendfile{,64} to COMPAT_SYSCALL_DEFINE
switch signalfd{,4}() to COMPAT_SYSCALL_DEFINE
make SYSCALL_DEFINE<n>-generated wrappers do asmlinkage_protect
make HAVE_SYSCALL_WRAPPERS unconditional
consolidate cond_syscall and SYSCALL_ALIAS declarations
teach SYSCALL_DEFINE<n> how to deal with long long/unsigned long long
get rid of duplicate logics in __SC_....[1-6] definitions
Both dump_stack() and show_stack() are currently implemented by each
architecture. show_stack(NULL, NULL) dumps the backtrace for the
current task as does dump_stack(). On some archs, dump_stack() prints
extra information - pid, utsname and so on - in addition to the
backtrace while the two are identical on other archs.
The usages in arch-independent code of the two functions indicate
show_stack(NULL, NULL) should print out bare backtrace while
dump_stack() is used for debugging purposes when something went wrong,
so it does make sense to print additional information on the task which
triggered dump_stack().
There's no reason to require archs to implement two separate but mostly
identical functions. It leads to unnecessary subtle information.
This patch expands the dummy fallback dump_stack() implementation in
lib/dump_stack.c such that it prints out debug information (taken from
x86) and invokes show_stack(NULL, NULL) and drops arch-specific
dump_stack() implementations in all archs except blackfin. Blackfin's
dump_stack() does something wonky that I don't understand.
Debug information can be printed separately by calling
dump_stack_print_info() so that arch-specific dump_stack()
implementation can still emit the same debug information. This is used
in blackfin.
This patch brings the following behavior changes.
* On some archs, an extra level in backtrace for show_stack() could be
printed. This is because the top frame was determined in
dump_stack() on those archs while generic dump_stack() can't do that
reliably. It can be compensated by inlining dump_stack() but not
sure whether that'd be necessary.
* Most archs didn't use to print debug info on dump_stack(). They do
now.
An example WARN dump follows.
WARNING: at kernel/workqueue.c:4841 init_workqueues+0x35/0x505()
Hardware name: empty
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #9
0000000000000009 ffff88007c861e08 ffffffff81c614dc ffff88007c861e48
ffffffff8108f50f ffffffff82228240 0000000000000040 ffffffff8234a03c
0000000000000000 0000000000000000 0000000000000000 ffff88007c861e58
Call Trace:
[<ffffffff81c614dc>] dump_stack+0x19/0x1b
[<ffffffff8108f50f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8108f56a>] warn_slowpath_null+0x1a/0x20
[<ffffffff8234a071>] init_workqueues+0x35/0x505
...
v2: CPU number added to the generic debug info as requested by s390
folks and dropped the s390 specific dump_stack(). This loses %ksp
from the debug message which the maintainers think isn't important
enough to keep the s390-specific dump_stack() implementation.
dump_stack_print_info() is moved to kernel/printk.c from
lib/dump_stack.c. Because linkage is per objecct file,
dump_stack_print_info() living in the same lib file as generic
dump_stack() means that archs which implement custom dump_stack()
- at this point, only blackfin - can't use dump_stack_print_info()
as that will bring in the generic version of dump_stack() too. v1
The v1 patch broke build on blackfin due to this issue. The build
breakage was reported by Fengguang Wu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390 bits]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull m68k update from Geert Uytterhoeven.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Remove inline strlen() implementation
m68k/atari: USB - add platform devices for EtherNAT/NetUSBee ISP1160 HCD
m68k: Implement ndelay() based on the existing udelay() logic
m68k/atari: EtherNAT - add interrupt chip definition for CPLD interrupts
m68k/atari: EtherNEC - add platform device support
m68k/atari: EtherNAT - platform device and IRQ support code
m68k/atari: use dedicated irq_chip for timer D interrupts
m68k/atari: ROM port ISA adapter support
m68k: Add missing cmpxchg64() if CONFIG_RMW_INSNS=y
Pull SMP/hotplug changes from Ingo Molnar:
"This is a pretty large, multi-arch series unifying and generalizing
the various disjunct pieces of idle routines that architectures have
historically copied from each other and have grown in random, wildly
inconsistent and sometimes buggy directions:
101 files changed, 455 insertions(+), 1328 deletions(-)
this went through a number of review and test iterations before it was
committed, it was tested on various architectures, was exposed to
linux-next for quite some time - nevertheless it might cause problems
on architectures that don't read the mailing lists and don't regularly
test linux-next.
This cat herding excercise was motivated by the -rt kernel, and was
brought to you by Thomas "the Whip" Gleixner."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
idle: Remove GENERIC_IDLE_LOOP config switch
um: Use generic idle loop
ia64: Make sure interrupts enabled when we "safe_halt()"
sparc: Use generic idle loop
idle: Remove unused ARCH_HAS_DEFAULT_IDLE
bfin: Fix typo in arch_cpu_idle()
xtensa: Use generic idle loop
x86: Use generic idle loop
unicore: Use generic idle loop
tile: Use generic idle loop
tile: Enter idle with preemption disabled
sh: Use generic idle loop
score: Use generic idle loop
s390: Use generic idle loop
powerpc: Use generic idle loop
parisc: Use generic idle loop
openrisc: Use generic idle loop
mn10300: Use generic idle loop
mips: Use generic idle loop
microblaze: Use generic idle loop
...
Use common help functions to free reserved pages.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables the initial Timer on coldfire 532x systems.
Without this, the scheduler will not be triggered and the system hangs,
after all sequential code is executed. It should also apply on later kernel
versions.
Signed-off-by: Christian Gieseler <christiangieseler@yahoo.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Add a configuration switch for supporting the Freescale M5373EVB board.
It is based on the newly added ColdFire 537x CPU support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 537x family is very similar internally to the ColdFire 532x
family. So with just a little extra configuration we can configure and
target them as well.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The M532x CPU platform support can be used on more ColdFire CPU families
than just the 532x types. So rename and reconfigure it to reflect that.
The ColdFire 537x family has virtualy identical internals to the 532x,
and so it will be able to share this code when we add support for them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The current CONFIG_M532x support definitions are actually common to a larger
set of version 3 ColdFire CPU types. In the future we want to add support for
the 537x family. It is very similar to the 532x internally, and will be able
to use most of the same definitions.
Create a CONFIG_M53xx option that is enabled to support any of the common
532x and 537x CPU types. Convert the current users of CONFIG_M532x to use
CONFIG_M53xx instead.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The contents of the m68k asm/dbg.h are never used, remove the file and
remove the one reference to it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
For coldfire with MMU enabled, data cache did not follow the configuration but
was configured in writethrough mode.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Kconfig symbol ROMVECSIZE is unused since commit
f84f52a5c1 ("m68knommu: clean up linker
script"). Let's clean up its Kconfig entry too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
GCC can replace a strncat() call with constant second argument into a
strlen + store, which results in a link error:
ERROR: "strlen" [net/ipv4/ip_tunnel.ko] undefined!
The inline function is a simple for loop in C. Other architectures
either use an asm optimized variant, or use the generic function from
lib/string.c.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add platform devices used by the isp116x-hcd driver for EtherNAT and
NetUSBee. Note that the NetUSBee also contains a RTL8019 Ethernet chip,
so its platform device is used to cover the EtherNEC case, too.
Register definitions thanks to David Galvez <dgalvez75@gmail.com>
[Geert] Conditionalize isp1160_delay() definition
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add a ndelay macro modeled after the Coldfire udelay(). The ISP1160
driver needs a 150ns delay, so we need to have ndelay().
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add a dedicated interrupt chip definition for the EtherNAT CPLD interrupts.
SMC91C111 and ISP1160 chips have separate interrupts that can be enabled
and disabled in a CPLD register at offset 0x23 from the card base.
Note the CPLD interrupt control register is mapped on demand, whenever any
interrupt enable/disable action is requested. The EtherNAT USB driver still
needs interrupts disabled around reset and start actions.
In particular, we cannot entirely rely on the irq_startup being called
first.
The smc91x and isp116x-hcd drivers will use this feature.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add platform device for the Atari ROM port ethernet adapter, EtherNEC.
This platform device will be used by the ne.c driver.
[Geert] Conditionalize platform device data structures
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add platform device and interrupt definitions necessary for the EtherNAT
Ethernet/USB adapter for the Falcon extension port. EtherNAT interrupt
numbers are 139/140 so the max. interrupt number for Atari has to be
increased.
[Geert] Conditionalize platform device data structures
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add a special irq_chip for the Atari MFP timer D interrupt,
which is used as a polling timer for EtherNEC and NetUSBee
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Atari ROM port ISA adapter support for EtherNEC and NetUSBee adapters
16 bit access for ROM port adapters follows debugging and
clarification by David Galvez <dgalvez75@gmail.com>. The NetUSBee
ISP1160 USB chip uses these macros.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
If CONFIG_RMW_INSNS=y:
drivers/block/blockconsole.c: In function ‘bcon_advance_console_bytes’:
drivers/block/blockconsole.c:164: error: implicit declaration of function ‘cmpxchg64’
Map cmpxchg64 to cmpxchg64_local, which is already mapped to
__cmpxchg64_local_generic, just like for the CONFIG_RMW_INSNS=n case.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
GENERIC_GPIO has been made equivalent to GPIOLIB in architecture code
and all driver code has been switch to depend on GPIOLIB. It is thus
safe to have GENERIC_GPIO removed.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Compiling for linux-3.9-rc1 and later fails with:
drivers/gpio/devres.c: In function 'devm_gpio_request_one':
drivers/gpio/devres.c:90:2: error: implicit declaration of function 'gpio_request_one' [-Werror=implicit-function-declaration]
So provide a local gpio_request_one() function. Code largely borrowed from
blackfin's local gpio_request_one() function.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The CONFIG_RPXLITE is not defined anywhere, which means that this board is not
supported anyway, and we can clean-up commproc.h a little.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-pcmcia@lists.infradead.org
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Force use of gpiolib for Coldfire, as a step towards the deprecation of
GENERIC_GPIO.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
In commit 887cbce0ad ("arch Kconfig: centralise ARCH_NO_VIRT_TO_BUS")
I introduced the config sybmol HAVE_VIRT_TO_BUS and selected that where
needed. I am not sure what I was thinking. Instead, just directly
select VIRT_TO_BUS where it is needed.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Somehow this select statement managed to squeeze itself between commit
0e152d8050 ("m68k: reorganize Kconfig
options to improve mmu/non-mmu selections") and commit
95e82747d6 ("m68k: drop unused Kconfig
symbols"). Whatever happened, there is no Kconfig symbol named EMAC_INC.
The select statement for that symbol is a nop. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Compiling for a ColdFire 528x CPU will result in:
arch/m68k/platform/coldfire/m528x.c: In function ‘m528x_uarts_init’:
arch/m68k/platform/coldfire/m528x.c:72: error: ‘MCF5282_GPIO_PUAPAR’ undeclared (first use in this function)
arch/m68k/platform/coldfire/m528x.c:72: error: (Each undeclared identifier is reported only once
arch/m68k/platform/coldfire/m528x.c:72: error: for each function it appears in.)
The MCF5282_GPIO_PUAPAR definition changed names in the ColdFire definitions
cleanup. It is now MCFGPIO_PUAPAR, so change it.
Not sure how this one got missed, 2 lines below it is the correct use of
this definition.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This patch fixes some broken #define's in the MC68328.h file.
Most of them are whitespaces and one is an incorrect define of TCN.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Commit dd1cb3a7c4 [merge MMU and non-MMU
versions of mm/init.c] unified mm/init.c for both MMU and non-MMU m68k
platforms. However, it broke when we build a non-MMU M68K Classic CPU kernel.
This fix builds a section that came from the MMU version only when we are
building a MMU kernel.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This patch adds the correct CPU name.
Without this, it just displays UNKNOWN at boot time and at '/proc/cpuinfo'.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Change it to CONFIG_HAVE_VIRT_TO_BUS and set it in all architecures
that already provide virt_to_bus().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
lockdep, but it's a mechanical change.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tiSY
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"The sweeping change is to make add_taint() explicitly indicate whether
to disable lockdep, but it's a mechanical change."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Add option to not sign modules during modules_install
MODSIGN: Add -s <signature> option to sign-file
MODSIGN: Specify the hash algorithm on sign-file command line
MODSIGN: Simplify Makefile with a Kconfig helper
module: clean up load_module a little more.
modpost: Ignore ARC specific non-alloc sections
module: constify within_module_*
taint: add explicit flag to show whether lock dep is still OK.
module: printk message when module signature fail taints kernel.
Pull signal handling cleanups from Al Viro:
"This is the first pile; another one will come a bit later and will
contain SYSCALL_DEFINE-related patches.
- a bunch of signal-related syscalls (both native and compat)
unified.
- a bunch of compat syscalls switched to COMPAT_SYSCALL_DEFINE
(fixing several potential problems with missing argument
validation, while we are at it)
- a lot of now-pointless wrappers killed
- a couple of architectures (cris and hexagon) forgot to save
altstack settings into sigframe, even though they used the
(uninitialized) values in sigreturn; fixed.
- microblaze fixes for delivery of multiple signals arriving at once
- saner set of helpers for signal delivery introduced, several
architectures switched to using those."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (143 commits)
x86: convert to ksignal
sparc: convert to ksignal
arm: switch to struct ksignal * passing
alpha: pass k_sigaction and siginfo_t using ksignal pointer
burying unused conditionals
make do_sigaltstack() static
arm64: switch to generic old sigaction() (compat-only)
arm64: switch to generic compat rt_sigaction()
arm64: switch compat to generic old sigsuspend
arm64: switch to generic compat rt_sigqueueinfo()
arm64: switch to generic compat rt_sigpending()
arm64: switch to generic compat rt_sigprocmask()
arm64: switch to generic sigaltstack
sparc: switch to generic old sigsuspend
sparc: COMPAT_SYSCALL_DEFINE does all sign-extension as well as SYSCALL_DEFINE
sparc: kill sign-extending wrappers for native syscalls
kill sparc32_open()
sparc: switch to use of generic old sigaction
sparc: switch sys_compat_rt_sigaction() to COMPAT_SYSCALL_DEFINE
mips: switch to generic sys_fork() and sys_clone()
...
Linus Torvalds