Commit Graph

61 Commits

Author SHA1 Message Date
NeilBrown 0efb9e6191 md: add MODULE_DESCRIPTION for all md related modules.
Suggested by  Oren Held <orenhe@il.ibm.com>

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown a2826aa92e md: support barrier requests on all personalities.
Previously barriers were only supported on RAID1.  This is because
other levels requires synchronisation across all devices and so needed
a different approach.
Here is that approach.

When a barrier arrives, we send a zero-length barrier to every active
device.  When that completes - and if the original request was not
empty -  we submit the barrier request itself (with the barrier flag
cleared) and then submit a fresh load of zero length barriers.

The barrier request itself is asynchronous, but any subsequent
request will block until the barrier completes.

The reason for clearing the barrier flag is that a barrier request is
allowed to fail.  If we pass a non-empty barrier through a striping
raid level it is conceivable that part of it could succeed and part
could fail.  That would be way too hard to deal with.
So if the first run of zero length barriers succeed, we assume all is
sufficiently well that we send the request and ignore errors in the
second run of barriers.

RAID5 needs extra care as write requests may not have been submitted
to the underlying devices yet.  So we flush the stripe cache before
proceeding with the barrier.

Note that the second set of zero-length barriers are submitted
immediately after the original request is submitted.  Thus when
a personality finds mddev->barrier to be set during make_request,
it should not return from make_request until the corresponding
per-device request(s) have been queued.

That will be done in later patches.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Andre Noll <maan@systemlinux.org>
2009-12-14 12:49:49 +11:00
NeilBrown 3fa841d7e7 md: report device as congested when suspended
This should writeback from coming when the device is temporarily
suspended.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:10:29 +10:00
Jens Axboe 1f98a13f62 bio: first step in sanitizing the bio->bi_rw flag testing
Get rid of any functions that test for these bits and make callers
use bio_rw_flagged() directly. Then it is at least directly apparent
what variable and flag they check.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-09-11 14:33:31 +02:00
NeilBrown 449aad3e25 md: Use revalidate_disk to effect changes in size of device.
As revalidate_disk calls check_disk_size_change, it will cause
any capacity change of a gendisk to be propagated to the blockdev
inode.  So use that instead of mucking about with locks and
i_size_write.

Also add a call to revalidate_disk in do_md_run and a few other places
where the gendisk capacity is changed.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-08-03 10:59:58 +10:00
Andre Noll ac5e7113e7 md: Push down data integrity code to personalities.
This patch replaces md_integrity_check() by two new public functions:
md_integrity_register() and md_integrity_add_rdev() which are both
personality-independent.

md_integrity_register() is called from the ->run and ->hot_remove
methods of all personalities that support data integrity.  The
function iterates over the component devices of the array and
determines if all active devices are integrity capable and if their
profiles match. If this is the case, the common profile is registered
for the mddev via blk_integrity_register().

The second new function, md_integrity_add_rdev() is called from the
->hot_add_disk methods, i.e. whenever a new device is being added
to a raid array. If the new device does not support data integrity,
or has a profile different from the one already registered, data
integrity for the mddev is disabled.

For raid0 and linear, only the call to md_integrity_register() from
the ->run method is necessary.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-08-03 10:59:47 +10:00
Martin K. Petersen 8f6c2e4b32 md: Use new topology calls to indicate alignment and I/O sizes
Switch MD over to the new disk_stack_limits() function which checks for
aligment and adjusts preferred I/O sizes when stacking.

Also indicate preferred I/O sizes where applicable.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-07-01 11:13:45 +10:00
NeilBrown 495d357301 md/linear: use call_rcu to free obsolete 'conf' structures.
Current, when we update the 'conf' structure, when adding a
drive to a linear array, we keep the old version around until
the array is finally stopped, as it is not safe to free it
immediately.

Now that we have rcu protection on all accesses to 'conf',
we can use call_rcu to free it more promptly.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-18 08:49:42 +10:00
SandeepKsinha af11c397fd md linear: Protecting mddev with rcu locks to avoid races
Due to the lack of memory ordering guarantees, we may have races around
mddev->conf.

In particular, the correct contents of the structure we get from
dereferencing ->private might not be visible to this CPU yet, and
they might not be correct w.r.t mddev->raid_disks.

This patch addresses the problem using rcu protection to avoid
such race conditions.

Signed-off-by: SandeepKsinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-18 08:49:35 +10:00
Andre Noll 0894cc3066 md: Move check for bitmap presence to personality code.
If the superblock of a component device indicates the presence of a
bitmap but the corresponding raid personality does not support bitmaps
(raid0, linear, multipath, faulty), then something is seriously wrong
and we'd better refuse to run such an array.

Currently, this check is performed while the superblocks are examined,
i.e. before entering personality code. Therefore the generic md layer
must know which raid levels support bitmaps and which do not.

This patch avoids this layer violation without adding identical code
to various personalities. This is accomplished by introducing a new
public function to md.c, md_check_no_bitmap(), which replaces the
hard-coded checks in the superblock loading functions.

A call to md_check_no_bitmap() is added to the ->run method of each
personality which does not support bitmaps and assembly is aborted
if at least one component device contains a bitmap.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-18 08:49:23 +10:00
NeilBrown 13f2682b72 md: raid0/linear: ensure device sizes are rounded to chunk size.
This is currently ensured by common code, but it is more reliable to
ensure it where it is needed in personality code.
All the other personalities that care already round the size to
the chunk_size.  raid0 and linear are the only hold-outs.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-18 08:48:55 +10:00
Andre Noll 9d8f036362 md: Make mddev->chunk_size sector-based.
This patch renames the chunk_size field to chunk_sectors with the
implied change of semantics.  Since

	is_power_of_2(chunk_size) = is_power_of_2(chunk_sectors << 9)
				  = is_power_of_2(chunk_sectors)

these bits don't need an adjustment for the shift.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-18 08:45:01 +10:00
Sandeep K Sinha aece3d1f40 md: Binary search in linear raid
Replace the linear search with binary search in which_dev.

Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-16 16:57:08 +10:00
Sandeep K Sinha 4db7cdc859 md: Removing num_sector and replacing start_sector with end_sector
Remove num_sectors from dev_info and replace start_sector with
end_sector.  This makes a lot of comparisons much simpler.

Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-16 16:56:13 +10:00
Sandeep K Sinha 45d4582f21 md: Removal of hash table in linear raid
Get rid of sector_div and hash table for linear raid and replace
with a linear search in which_dev.
The hash table adds a lot of complexity for little if any gain.
Ultimately a binary search will be used which will have smaller
cache foot print, a similar number of memory access, and no
divisions.

Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-16 16:55:26 +10:00
NeilBrown 070ec55d07 md: remove mddev_to_conf "helper" macro
Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.

So open code the macro everywhere and remove the pointless cast.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-16 16:54:21 +10:00
Martin K. Petersen ae03bf639a block: Use accessor functions for queue limits
Convert all external users of queue limits to using wrapper functions
instead of poking the request queue variables directly.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-22 23:22:54 +02:00
Dan Williams 1f403624bd md: centralize ->array_sectors modifications
Get personalities out of the business of directly modifying
->array_sectors.  Lays groundwork to introduce policy on when
->array_sectors can be modified.

Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-03-31 14:59:03 +11:00
Dan Williams 80c3a6ce4b md: add 'size' as a personality method
In preparation for giving userspace control over ->array_sectors we need
to be able to retrieve the 'default' size, and the 'anticipated' size
when a reshape is requested.  For personalities that do not reshape emit
a warning if anything but the default size is requested.

In the raid5 case we need to update ->previous_raid_disks to make the
new 'default' size available.

Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-03-31 14:57:49 +11:00
Andre Noll dd8ac336c1 md: Represent raid device size in sectors.
This patch renames the "size" field of struct mdk_rdev_s to
"sectors" and changes this field to store sectors instead of
blocks.

All users of this field, linear.c, raid0.c and md.c, are fixed up
accordingly which gets rid of many multiplications and divisions.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:33:13 +11:00
NeilBrown 43b2e5d86d md: move md_k.h from include/linux/raid/ to drivers/md/
It really is nicer to keep related code together..

Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:33:13 +11:00
NeilBrown bff61975b3 md: move lots of #include lines out of .h files and into .c
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h

Remove include/raid/md.h as its only remaining use was to #include
other files.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:33:13 +11:00
Christoph Hellwig ef740c372d md: move headers out of include/linux/raid/
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away.  md.h is left where it is for now as there
are some uses from the outside.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:27:03 +11:00
Andre Noll 852c8bf484 md: Fix a bug in linear.c causing which_dev() to return the wrong device.
ab5bd5cbc8 introduced the following
bug in linear software raid for large arrays on 32 bit machines:

which_dev() computes the device holding a given sector by shifting
down the sector number to a 32 bit range, dividing by the array
spacing and looking up the resulting index in the hash table of
the array.

Because the computed index might be slightly too small, a loop at
the end of which_dev() increases the index until the given sector
actually falls into the range of the device associated with that index.

The changes of the above mentioned commit caused this loop to check
whether the _index_ rather than the sector number is small enough,
effectively bypassing the loop and thus possibly returning the wrong
device.

As reported by Simon Kirby, this leads to errors such as

	linear_make_request: Sector 2340486136 out of bounds on dev sdi: 156301312 sectors, offset 2109870464

Fix this bug by introducing a local variable for the index so that
the variable containing the passed sector is left unchanged.

Cc: stable@kernel.org
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-02-06 15:10:52 +11:00
Cheng Renquan 159ec1fc06 md: use list_for_each_entry macro directly
The rdev_for_each macro defined in <linux/raid/md_k.h> is identical to
list_for_each_entry_safe, from <linux/list.h>, it should be defined to
use list_for_each_entry_safe, instead of reinventing the wheel.

But some calls to each_entry_safe don't really need a safe version,
just a direct list_for_each_entry is enough, this could save a temp
variable (tmp) in every function that used rdev_for_each.

In this patch, most rdev_for_each loops are replaced by list_for_each_entry,
totally save many tmp vars; and only in the other situations that will call
list_del to delete an entry, the safe version is used.

Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-01-09 08:31:08 +11:00
Andre Noll f1cd14ae52 md: linear: Fix a division by zero bug for very small arrays.
We currently oops with a divide error on starting a linear software
raid array consisting of at least two very small (< 500K) devices.

The bug is caused by the calculation of the hash table size which
tries to compute sector_div(sz, base) with "base" being zero due to
the small size of the component devices of the array.

Fix this by requiring the hash spacing to be at least one which
implies that also "base" is non-zero.

This bug has existed since about 2.6.14.

Cc: stable@kernel.org
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-11-06 19:41:24 +11:00
NeilBrown fb4d8c76e5 md: Remove unnecessary #includes, #defines, and function declarations.
A lot of cruft has gathered over the years.  Time to remove it.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll ab5bd5cbc8 md: Convert remaining 1k representations in linear.c to sectors.
This patch renames hash_spacing and preshift to  spacing and
sector_shift respectively with the following change of semantics:

Case 1: (sizeof(sector_t) <= sizeof(u32)).
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

In this case, we have sector_shift = preshift = 0 and spacing =
2 * hash_spacing.

Hence, the index for the hash table which is computed by the new code
in which_dev() as sector / spacing equals the old value which was
(sector/2) / hash_spacing.

Note also that the value of nb_zone stays the same because both sz
and base double.

Case 2: (sizeof(sector_t) > sizeof(u32)).
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

(aka the shifting dance case). Here we have sector_shift = preshift +
1 and

spacing = 2 * hash_spacing

during the computation of nb_zone and curr_sector, but

spacing = hash_spacing

in which_dev() because in the last hunk of the patch for linear.c we
shift down conf->spacing (= 2 * hash_spacing) by one more bit than
in the old code.

Hence in the computation of nb_zone, sz and base have the same value
as before, so nb_zone is not affected. Also curr_sector in the next
hunk stays the same.

In which_dev() the hash table index is computed as

(sector >> sector_shift) / spacing

In view of sector_shift = preshift + 1 and spacing = hash_spacing,
this equals

((sector/2) >> preshift) / hash_spacing

which is the value computed by the old code.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll 23242fbb47 md: linear.c: Make two local variables sector-based.
This is a preparation for representing also the remaining fields of struct
linear_private_data as sectors.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll 6283815d18 md: linear: Represent dev_info->size and dev_info->offset in sectors.
Rename them to num_sectors and start_sector which is more descriptive.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll 451708d2a4 md: linear.c: Remove broken debug code.
conf->smallest_size is undefined since day one of the git repo..

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll 481d86c7eb md: linear.c: Remove pointless initialization of curr_offset.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll e61130228e md: linear.c: Fix typo in comment.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Denis ChengRq 6feef531f5 block: mark bio_split_pool static
Since all bio_split calls refer the same single bio_split_pool, the bio_split
function can use bio_split_pool directly instead of the mempool_t parameter;

then the mempool_t parameter can be removed from bio_split param list, and
bio_split_pool is only referred in fs/bio.c file, can be marked static.

Signed-off-by: Denis ChengRq <crquan@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:57:05 +02:00
Tejun Heo 074a7aca7a block: move stats from disk to part0
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...

* part_stat_*() now updates part0 together if the specified partition
  is not part0.  ie. part_stat_*() are now essentially all_stat_*().

* {disk|all}_stat_*() are gone.

* part_round_stats() is updated similary.  It handles part0 stats
  automatically and disk_round_stats() is killed.

* part_{inc|dec}_in_fligh() is implemented which automatically updates
  part0 stats for parts other than part0.

* disk_map_sector_rcu() is updated to return part0 if no part matches.
  Combined with the above changes, this makes NULL special case
  handling in callers unnecessary.

* Separate stats show code paths for disk are collapsed into part
  stats show code paths.

* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()

While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:08 +02:00
Tejun Heo c995905916 block: fix diskstats access
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters.  It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.

This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access).  diskstats access
should always be enclosed between the two functions.  As such, there's
no need for the versions which disables preemption.  They're removed
and double underbars ones are renamed to drop the underbars.  As an
extra argument is added, there's no danger of using the old version
unconverted.

disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.

This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others.  Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:06 +02:00
Linus Torvalds 8a392625b6 Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md: (52 commits)
  md: Protect access to mddev->disks list using RCU
  md: only count actual openers as access which prevent a 'stop'
  md: linear: Make array_size sector-based and rename it to array_sectors.
  md: Make mddev->array_size sector-based.
  md: Make super_type->rdev_size_change() take sector-based sizes.
  md: Fix check for overlapping devices.
  md: Tidy up rdev_size_store a bit:
  md: Remove some unused macros.
  md: Turn rdev->sb_offset into a sector-based quantity.
  md: Make calc_dev_sboffset() return a sector count.
  md: Replace calc_dev_size() by calc_num_sectors().
  md: Make update_size() take the number of sectors.
  md: Better control of when do_md_stop is allowed to stop the array.
  md: get_disk_info(): Don't convert between signed and unsigned and back.
  md: Simplify restart_array().
  md: alloc_disk_sb(): Return proper error value.
  md: Simplify sb_equal().
  md: Simplify uuid_equal().
  md: sb_equal(): Fix misleading printk.
  md: Fix a typo in the comment to cmd_match().
  ...
2008-07-21 10:29:12 -07:00
Andre Noll d6e2215052 md: linear: Make array_size sector-based and rename it to array_sectors.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 17:05:25 +10:00
Andre Noll f233ea5c9e md: Make mddev->array_size sector-based.
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 17:05:22 +10:00
Alasdair G Kergon cc371e66e3 Add bvec_merge_data to handle stacked devices and ->merge_bvec()
When devices are stacked, one device's merge_bvec_fn may need to perform
the mapping and then call one or more functions for its underlying devices.

The following bio fields are used:
  bio->bi_sector
  bio->bi_bdev
  bio->bi_size
  bio->bi_rw  using bio_data_dir()

This patch creates a new struct bvec_merge_data holding a copy of those
fields to avoid having to change them directly in the struct bio when
going down the stack only to have to change them back again on the way
back up.  (And then when the bio gets mapped for real, the whole
exercise gets repeated, but that's a problem for another day...)

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-07-03 13:21:15 +02:00
Nikanth Karthikesan 13864515f7 linear: correct disk numbering error check
From: "Nikanth Karthikesan" <knikanth@novell.com>

Correct disk numbering problem check.

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
2008-06-28 08:31:19 +10:00
Neil Brown e7e72bf641 Remove blkdev warning triggered by using md
As setting and clearing queue flags now requires that we hold a spinlock
on the queue, and as blk_queue_stack_limits is called without that lock,
get the lock inside blk_queue_stack_limits.

For blk_queue_stack_limits to be able to find the right lock, each md
personality needs to set q->queue_lock to point to the appropriate lock.
Those personalities which didn't previously use a spin_lock, us
q->__queue_lock.  So always initialise that lock when allocated.

With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no
longer cause warnings as it will be clear that the proper lock is held.

Thanks to Dan Williams for review and fixing the silly bugs.

Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nick Piggin <npiggin@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jacek Luczak <difrost.kernel@gmail.com>
Cc: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-14 19:11:15 -07:00
NeilBrown d089c6af10 md: change ITERATE_RDEV to rdev_for_each
As this is more in line with common practice in the kernel.  Also swap the
args around to be more like list_for_each.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:19 -08:00
Alan D. Brunelle 2ad8b1ef11 Add UNPLUG traces to all appropriate places
Added blk_unplug interface, allowing all invocations of unplugs to result
in a generated blktrace UNPLUG.

Signed-off-by: Alan D. Brunelle <Alan.Brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-11-09 13:41:32 +01:00
Jens Axboe fd5d806266 block: convert blkdev_issue_flush() to use empty barriers
Then we can get rid of ->issue_flush_fn() and all the driver private
implementations of that.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-16 11:05:02 +02:00
NeilBrown 6712ecf8f6 Drop 'size' argument from bio_endio and bi_end_io
As bi_end_io is only called once when the reqeust is complete,
the 'size' argument is now redundant.  Remove it.

Now there is no need for bio_endio to subtract the size completed
from bi_size.  So don't do that either.

While we are at it, change bi_end_io to return void.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10 09:25:57 +02:00
Jens Axboe 165125e1e4 [BLOCK] Get rid of request_queue_t typedef
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-07-24 09:28:11 +02:00
NeilBrown a778b73ff7 md: fix bug with linear hot-add and elsewhere
Adding a drive to a linear array seems to have stopped working, due to changes
elsewhere in md, and insufficient ongoing testing...

So the patch to make linear hot-add work in the first place introduced a
subtle bug elsewhere that interracts poorly with older version of mdadm.

This fixes it all up.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-23 20:14:14 -07:00
Andy Isaacson bed31ed9e1 [PATCH] fix read past end of array in md/linear.c
When iterating through an array, one must be careful to test one's index
variable rather than another similarly-named variable.

The loop will read off the end of conf->disks[] in the following
(pathological) case:

  % dd bs=1 seek=840716287 if=/dev/zero of=d1 count=1
  % for i in 2 3 4; do dd if=/dev/zero of=d$i bs=1k count=$(($i+150)); done
  % ./vmlinux ubd0=root ubd1=d1 ubd2=d2 ubd3=d3 ubd4=d4
  # mdadm -C /dev/md0 --level=linear --raid-devices=4 /dev/ubd[1234]

adding some printks, I saw this:

  [42949374.960000] hash_spacing = 821120
  [42949374.960000] cnt          = 4
  [42949374.960000] min_spacing  = 801
  [42949374.960000] j=0 size=820928 sz=820928
  [42949374.960000] i=0 sz=820928 hash_spacing=820928
  [42949374.960000] j=1 size=64 sz=64
  [42949374.960000] j=2 size=64 sz=128
  [42949374.960000] j=3 size=64 sz=192
  [42949374.960000] j=4 size=1515870810 sz=1515871002

Cc: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Neil Brown <neilb@cse.unsw.edu.au>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-16 19:25:03 -07:00
NeilBrown 26be34dc3a [PATCH] md: define backing_dev_info.congested_fn for raid0 and linear
Each backing_dev needs to be able to report whether it is congested, either by
modulating BDI_*_congested in ->state, or by defining a ->congested_fn.
md/raid did neither of these.  This patch add a congested_fn which simply
checks all component devices to see if they are congested.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00