Current handling of CHECKSUM_COMPLETE packets by the UDP stack is
incorrect for any packet that has an incorrect checksum value.
udp4/6_csum_init() will both make a call to
__skb_checksum_validate_complete() to initialize/validate the csum
field when receiving a CHECKSUM_COMPLETE packet. When this packet
fails validation, skb->csum will be overwritten with the pseudoheader
checksum so the packet can be fully validated by software, but the
skb->ip_summed value will be left as CHECKSUM_COMPLETE so that way
the stack can later warn the user about their hardware spewing bad
checksums. Unfortunately, leaving the SKB in this state can cause
problems later on in the checksum calculation.
Since the the packet is still marked as CHECKSUM_COMPLETE,
udp_csum_pull_header() will SUBTRACT the checksum of the UDP header
from skb->csum instead of adding it, leaving us with a garbage value
in that field. Once we try to copy the packet to userspace in the
udp4/6_recvmsg(), we'll make a call to skb_copy_and_csum_datagram_msg()
to checksum the packet data and add it in the garbage skb->csum value
to perform our final validation check.
Since the value we're validating is not the proper checksum, it's possible
that the folded value could come out to 0, causing us not to drop the
packet. Instead, we believe that the packet was checksummed incorrectly
by hardware since skb->ip_summed is still CHECKSUM_COMPLETE, and we attempt
to warn the user with netdev_rx_csum_fault(skb->dev);
Unfortunately, since this is the UDP path, skb->dev has been overwritten
by skb->dev_scratch and is no longer a valid pointer, so we end up
reading invalid memory.
This patch addresses this problem in two ways:
1) Do not use the dev pointer when calling netdev_rx_csum_fault()
from skb_copy_and_csum_datagram_msg(). Since this gets called
from the UDP path where skb->dev has been overwritten, we have
no way of knowing if the pointer is still valid. Also for the
sake of consistency with the other uses of
netdev_rx_csum_fault(), don't attempt to call it if the
packet was checksummed by software.
2) Add better CHECKSUM_COMPLETE handling to udp4/6_csum_init().
If we receive a packet that's CHECKSUM_COMPLETE that fails
verification (i.e. skb->csum_valid == 0), check who performed
the calculation. It's possible that the checksum was done in
software by the network stack earlier (such as Netfilter's
CONNTRACK module), and if that says the checksum is bad,
we can drop the packet immediately instead of waiting until
we try and copy it to userspace. Otherwise, we need to
mark the SKB as CHECKSUM_NONE, since the skb->csum field
no longer contains the full packet checksum after the
call to __skb_checksum_validate_complete().
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Fixes: c84d949057 ("udp: copy skb->truesize in the first cache line")
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2276f58ac5 ("udp: use a separate rx queue for packet reception")
turned static inline __skb_recv_udp() from being a trivial helper around
__skb_recv_datagram() into a UDP specific implementaion, making it
EXPORT_SYMBOL_GPL() at the same time.
There are external modules that got broken by __skb_recv_udp() not being
visible to them. Let's unbreak them by making __skb_recv_udp EXPORT_SYMBOL().
Rationale (one of those) why this is actually "technically correct" thing
to do: __skb_recv_udp() used to be an inline wrapper around
__skb_recv_datagram(), which itself (still, and correctly so, I believe)
is EXPORT_SYMBOL().
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 2276f58ac5 ("udp: use a separate rx queue for packet reception")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the socket lookup cost in udp_gro_receive if no socket has a
udp tunnel callback configured.
udp_sk(sk)->gro_receive requires a registration with
setup_udp_tunnel_sock, which enables the static key.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful to be able to use the same socket for listening in a
specific VRF, as for sending multicast packets out of a specific
interface. However, the bound device on the socket currently takes
precedence and results in the packets not being sent.
Relax the condition on overriding the output interface to use for
sending packets out of UDP, raw and ping sockets to allow multicast
packets to be sent using the specified multicast interface.
Signed-off-by: Robert Shearman <rshearma@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2abb7cdc0d ("udp: Add support for doing checksum
unnecessary conversion") left out the early demux path for
connected sockets. As a result IP_CMSG_CHECKSUM gives wrong
values for such socket when GRO is not enabled/available.
This change addresses the issue by moving the csum conversion to a
common helper and using such helper in both the default and the
early demux rx path.
Fixes: 2abb7cdc0d ("udp: Add support for doing checksum unnecessary conversion")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a BPF_PROG_TYPE_SK_REUSEPORT bpf prog to select a
SO_REUSEPORT sk from a BPF_MAP_TYPE_REUSEPORT_ARRAY introduced in
the earlier patch. "bpf_run_sk_reuseport()" will return -ECONNREFUSED
when the BPF_PROG_TYPE_SK_REUSEPORT prog returns SK_DROP.
The callers, in inet[6]_hashtable.c and ipv[46]/udp.c, are modified to
handle this case and return NULL immediately instead of continuing the
sk search from its hashtable.
It re-uses the existing SO_ATTACH_REUSEPORT_EBPF setsockopt to attach
BPF_PROG_TYPE_SK_REUSEPORT. The "sk_reuseport_attach_bpf()" will check
if the attaching bpf prog is in the new SK_REUSEPORT or the existing
SOCKET_FILTER type and then check different things accordingly.
One level of "__reuseport_attach_prog()" call is removed. The
"sk_unhashed() && ..." and "sk->sk_reuseport_cb" tests are pushed
back to "reuseport_attach_prog()" in sock_reuseport.c. sock_reuseport.c
seems to have more knowledge on those test requirements than filter.c.
In "reuseport_attach_prog()", after new_prog is attached to reuse->prog,
the old_prog (if any) is also directly freed instead of returning the
old_prog to the caller and asking the caller to free.
The sysctl_optmem_max check is moved back to the
"sk_reuseport_attach_filter()" and "sk_reuseport_attach_bpf()".
As of other bpf prog types, the new BPF_PROG_TYPE_SK_REUSEPORT is only
bounded by the usual "bpf_prog_charge_memlock()" during load time
instead of bounded by both bpf_prog_charge_memlock and sysctl_optmem_max.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch adds a BPF_PROG_TYPE_SK_REUSEPORT which can select
a SO_REUSEPORT sk from a BPF_MAP_TYPE_REUSEPORT_ARRAY. Like other
non SK_FILTER/CGROUP_SKB program, it requires CAP_SYS_ADMIN.
BPF_PROG_TYPE_SK_REUSEPORT introduces "struct sk_reuseport_kern"
to store the bpf context instead of using the skb->cb[48].
At the SO_REUSEPORT sk lookup time, it is in the middle of transiting
from a lower layer (ipv4/ipv6) to a upper layer (udp/tcp). At this
point, it is not always clear where the bpf context can be appended
in the skb->cb[48] to avoid saving-and-restoring cb[]. Even putting
aside the difference between ipv4-vs-ipv6 and udp-vs-tcp. It is not
clear if the lower layer is only ipv4 and ipv6 in the future and
will it not touch the cb[] again before transiting to the upper
layer.
For example, in udp_gro_receive(), it uses the 48 byte NAPI_GRO_CB
instead of IP[6]CB and it may still modify the cb[] after calling
the udp[46]_lib_lookup_skb(). Because of the above reason, if
sk->cb is used for the bpf ctx, saving-and-restoring is needed
and likely the whole 48 bytes cb[] has to be saved and restored.
Instead of saving, setting and restoring the cb[], this patch opts
to create a new "struct sk_reuseport_kern" and setting the needed
values in there.
The new BPF_PROG_TYPE_SK_REUSEPORT and "struct sk_reuseport_(kern|md)"
will serve all ipv4/ipv6 + udp/tcp combinations. There is no protocol
specific usage at this point and it is also inline with the current
sock_reuseport.c implementation (i.e. no protocol specific requirement).
In "struct sk_reuseport_md", this patch exposes data/data_end/len
with semantic similar to other existing usages. Together
with "bpf_skb_load_bytes()" and "bpf_skb_load_bytes_relative()",
the bpf prog can peek anywhere in the skb. The "bind_inany" tells
the bpf prog that the reuseport group is bind-ed to a local
INANY address which cannot be learned from skb.
The new "bind_inany" is added to "struct sock_reuseport" which will be
used when running the new "BPF_PROG_TYPE_SK_REUSEPORT" bpf prog in order
to avoid repeating the "bind INANY" test on
"sk_v6_rcv_saddr/sk->sk_rcv_saddr" every time a bpf prog is run. It can
only be properly initialized when a "sk->sk_reuseport" enabled sk is
adding to a hashtable (i.e. during "reuseport_alloc()" and
"reuseport_add_sock()").
The new "sk_select_reuseport()" is the main helper that the
bpf prog will use to select a SO_REUSEPORT sk. It is the only function
that can use the new BPF_MAP_TYPE_REUSEPORT_ARRAY. As mentioned in
the earlier patch, the validity of a selected sk is checked in
run time in "sk_select_reuseport()". Doing the check in
verification time is difficult and inflexible (consider the map-in-map
use case). The runtime check is to compare the selected sk's reuseport_id
with the reuseport_id that we want. This helper will return -EXXX if the
selected sk cannot serve the incoming request (e.g. reuseport_id
not match). The bpf prog can decide if it wants to do SK_DROP as its
discretion.
When the bpf prog returns SK_PASS, the kernel will check if a
valid sk has been selected (i.e. "reuse_kern->selected_sk != NULL").
If it does , it will use the selected sk. If not, the kernel
will select one from "reuse->socks[]" (as before this patch).
The SK_DROP and SK_PASS handling logic will be in the next patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
skb_shinfo(skb)->tx_flags is derived from sk->sk_tsflags, possibly
after modification by __sock_cmsg_send, by calling sock_tx_timestamp.
The IPv4 and IPv6 paths do this conversion differently. In IPv4, the
individual protocols that support tx timestamps call this function
and store the result in ipc.tx_flags. In IPv6, sock_tx_timestamp is
called in __ip6_append_data.
There is no need to store both tx_flags and ts_flags in the cookie
as one is derived from the other. Convert when setting up the cork
and remove the redundant field. This is similar to IPv6, only have
the conversion happen only once per datagram, in ip(6)_setup_cork.
Also change __ip6_append_data to match __ip_append_data. Only update
tskey if timestamping is enabled with OPT_ID. The SOCK_.. test is
redundant: only valid protocols can have non-zero cork->tx_flags.
After this change the IPv4 and IPv6 logic is the same.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the cookie in one location to reduce code duplication and
avoid bugs from inconsistent initialization, such as that fixed in
commit 9887cba199 ("ip: limit use of gso_size to udp").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a transmit_time field to struct inet_cork, then copy the
timestamp from the CMSG cookie at ip_setup_cork() so we can
safely copy it into the skb later during __ip_make_skb().
For the raw fast path, just perform the copy at raw_send_hdrinc().
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit 6b229cf77d ("udp: add batching to udp_rmem_release()")
the sk_rmem_alloc field does not measure exactly anymore the
receive queue length, because we batch the rmem release. The issue
is really apparent only after commit 0d4a6608f6 ("udp: do rmem bulk
free even if the rx sk queue is empty"): the user space can easily
check for an empty socket with not-0 queue length reported by the 'ss'
tool or the procfs interface.
We need to use a custom UDP helper to report the correct queue length,
taking into account the forward allocation deficit.
Reported-by: trevor.francis@46labs.com
Fixes: 6b229cf77d ("UDP: add batching to udp_rmem_release()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-06-05
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a new BPF hook for sendmsg similar to existing hooks for bind and
connect: "This allows to override source IP (including the case when it's
set via cmsg(3)) and destination IP:port for unconnected UDP (slow path).
TCP and connected UDP (fast path) are not affected. This makes UDP support
complete, that is, connected UDP is handled by connect hooks, unconnected
by sendmsg ones.", from Andrey.
2) Rework of the AF_XDP API to allow extending it in future for type writer
model if necessary. In this mode a memory window is passed to hardware
and multiple frames might be filled into that window instead of just one
that is the case in the current fixed frame-size model. With the new
changes made this can be supported without having to add a new descriptor
format. Also, core bits for the zero-copy support for AF_XDP have been
merged as agreed upon, where i40e bits will be routed via Jeff later on.
Various improvements to documentation and sample programs included as
well, all from Björn and Magnus.
3) Given BPF's flexibility, a new program type has been added to implement
infrared decoders. Quote: "The kernel IR decoders support the most
widely used IR protocols, but there are many protocols which are not
supported. [...] There is a 'long tail' of unsupported IR protocols,
for which lircd is need to decode the IR. IR encoding is done in such
a way that some simple circuit can decode it; therefore, BPF is ideal.
[...] user-space can define a decoder in BPF, attach it to the rc
device through the lirc chardev.", from Sean.
4) Several improvements and fixes to BPF core, among others, dumping map
and prog IDs into fdinfo which is a straight forward way to correlate
BPF objects used by applications, removing an indirect call and therefore
retpoline in all map lookup/update/delete calls by invoking the callback
directly for 64 bit archs, adding a new bpf_skb_cgroup_id() BPF helper
for tc BPF programs to have an efficient way of looking up cgroup v2 id
for policy or other use cases. Fixes to make sure we zero tunnel/xfrm
state that hasn't been filled, to allow context access wrt pt_regs in
32 bit archs for tracing, and last but not least various test cases
for fixes that landed in bpf earlier, from Daniel.
5) Get rid of the ndo_xdp_flush API and extend the ndo_xdp_xmit with
a XDP_XMIT_FLUSH flag instead which allows to avoid one indirect
call as flushing is now merged directly into ndo_xdp_xmit(), from Jesper.
6) Add a new bpf_get_current_cgroup_id() helper that can be used in
tracing to retrieve the cgroup id from the current process in order
to allow for e.g. aggregation of container-level events, from Yonghong.
7) Two follow-up fixes for BTF to reject invalid input values and
related to that also two test cases for BPF kselftests, from Martin.
8) Various API improvements to the bpf_fib_lookup() helper, that is,
dropping MPLS bits which are not fully hashed out yet, rejecting
invalid helper flags, returning error for unsupported address
families as well as renaming flowlabel to flowinfo, from David.
9) Various fixes and improvements to sockmap BPF kselftests in particular
in proper error detection and data verification, from Prashant.
10) Two arm32 BPF JIT improvements. One is to fix imm range check with
regards to whether immediate fits into 24 bits, and a naming cleanup
to get functions related to rsh handling consistent to those handling
lsh, from Wang.
11) Two compile warning fixes in BPF, one for BTF and a false positive
to silent gcc in stack_map_get_build_id_offset(), from Arnd.
12) Add missing seg6.h header into tools include infrastructure in order
to fix compilation of BPF kselftests, from Mathieu.
13) Several formatting cleanups in the BPF UAPI helper description that
also fix an error during rst2man compilation, from Quentin.
14) Hide an unused variable in sk_msg_convert_ctx_access() when IPv6 is
not built into the kernel, from Yue.
15) Remove a useless double assignment in dev_map_enqueue(), from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is now possible to enable the libified nf_tproxy modules without
also enabling NETFILTER_XT_TARGET_TPROXY, which throws off the
ifdef logic in the udp core code:
net/ipv6/netfilter/nf_tproxy_ipv6.o: In function `nf_tproxy_get_sock_v6':
nf_tproxy_ipv6.c:(.text+0x1a8): undefined reference to `udp6_lib_lookup'
net/ipv4/netfilter/nf_tproxy_ipv4.o: In function `nf_tproxy_get_sock_v4':
nf_tproxy_ipv4.c:(.text+0x3d0): undefined reference to `udp4_lib_lookup'
We can actually simplify the conditions now to provide the two functions
exactly when they are needed.
Fixes: 45ca4e0cf2 ("netfilter: Libify xt_TPROXY")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Máté Eckl <ecklm94@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull aio updates from Al Viro:
"Majority of AIO stuff this cycle. aio-fsync and aio-poll, mostly.
The only thing I'm holding back for a day or so is Adam's aio ioprio -
his last-minute fixup is trivial (missing stub in !CONFIG_BLOCK case),
but let it sit in -next for decency sake..."
* 'work.aio-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
aio: sanitize the limit checking in io_submit(2)
aio: fold do_io_submit() into callers
aio: shift copyin of iocb into io_submit_one()
aio_read_events_ring(): make a bit more readable
aio: all callers of aio_{read,write,fsync,poll} treat 0 and -EIOCBQUEUED the same way
aio: take list removal to (some) callers of aio_complete()
aio: add missing break for the IOCB_CMD_FDSYNC case
random: convert to ->poll_mask
timerfd: convert to ->poll_mask
eventfd: switch to ->poll_mask
pipe: convert to ->poll_mask
crypto: af_alg: convert to ->poll_mask
net/rxrpc: convert to ->poll_mask
net/iucv: convert to ->poll_mask
net/phonet: convert to ->poll_mask
net/nfc: convert to ->poll_mask
net/caif: convert to ->poll_mask
net/bluetooth: convert to ->poll_mask
net/sctp: convert to ->poll_mask
net/tipc: convert to ->poll_mask
...
In addition to already existing BPF hooks for sys_bind and sys_connect,
the patch provides new hooks for sys_sendmsg.
It leverages existing BPF program type `BPF_PROG_TYPE_CGROUP_SOCK_ADDR`
that provides access to socket itlself (properties like family, type,
protocol) and user-passed `struct sockaddr *` so that BPF program can
override destination IP and port for system calls such as sendto(2) or
sendmsg(2) and/or assign source IP to the socket.
The hooks are implemented as two new attach types:
`BPF_CGROUP_UDP4_SENDMSG` and `BPF_CGROUP_UDP6_SENDMSG` for UDPv4 and
UDPv6 correspondingly.
UDPv4 and UDPv6 separate attach types for same reason as sys_bind and
sys_connect hooks, i.e. to prevent reading from / writing to e.g.
user_ip6 fields when user passes sockaddr_in since it'd be out-of-bound.
The difference with already existing hooks is sys_sendmsg are
implemented only for unconnected UDP.
For TCP it doesn't make sense to change user-provided `struct sockaddr *`
at sendto(2)/sendmsg(2) time since socket either was already connected
and has source/destination set or wasn't connected and call to
sendto(2)/sendmsg(2) would lead to ENOTCONN anyway.
Connected UDP is already handled by sys_connect hooks that can override
source/destination at connect time and use fast-path later, i.e. these
hooks don't affect UDP fast-path.
Rewriting source IP is implemented differently than that in sys_connect
hooks. When sys_sendmsg is used with unconnected UDP it doesn't work to
just bind socket to desired local IP address since source IP can be set
on per-packet basis by using ancillary data (cmsg(3)). So no matter if
socket is bound or not, source IP has to be rewritten on every call to
sys_sendmsg.
To do so two new fields are added to UAPI `struct bpf_sock_addr`;
* `msg_src_ip4` to set source IPv4 for UDPv4;
* `msg_src_ip6` to set source IPv6 for UDPv6.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
UDP GSO delays final datagram construction to the GSO layer. This
conflicts with protocol transformations.
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
CC: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variants of proc_create{,_data} that directly take a struct seq_operations
and deal with network namespaces in ->open and ->release. All callers of
proc_create + seq_open_net converted over, and seq_{open,release}_net are
removed entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix more memory leaks in ip_cmsg_send() callers. Part of them were fixed
earlier in 919483096b.
* udp_sendmsg one was there since the beginning when linux sources were
first added to git;
* ping_v4_sendmsg one was copy/pasted in c319b4d76b.
Whenever return happens in udp_sendmsg() or ping_v4_sendmsg() IP options
have to be freed if they were allocated previously.
Add label so that future callers (if any) can use it instead of kfree()
before return that is easy to forget.
Fixes: c319b4d76b (net: ipv4: add IPPROTO_ICMP socket kind)
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Damir reported a breakage of SO_BINDTODEVICE for UDP sockets.
In absence of VRF devices, after commit fb74c27735 ("net:
ipv4: add second dif to udp socket lookups") the dif mismatch
isn't fatal anymore for UDP socket lookup with non null
sk_bound_dev_if, breaking SO_BINDTODEVICE semantics.
This changeset addresses the issue making the dif match mandatory
again in the above scenario.
Reported-by: Damir Mansurov <dnman@oktetlabs.ru>
Fixes: fb74c27735 ("net: ipv4: add second dif to udp socket lookups")
Fixes: 1801b570dd ("net: ipv6: add second dif to udp socket lookups")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No changes in refcount semantics -- key init is false; replace
static_key_enable with static_branch_enable
static_key_slow_inc|dec with static_branch_inc|dec
static_key_false with static_branch_unlikely
Added a '_key' suffix to udp and udpv6 encap_needed, for better
self documentation.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to record the number of segments that will be generated when this
frame is segmented. The expectation is that if gso_size is set then
gso_segs is set as well. Without this some drivers such as ixgbe get
confused if they attempt to offload this as they record 0 segments for the
entire packet instead of the correct value.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot managed to send a udp gso packet without checksum offload into
the gso stack by disabling tx checksum (UDP_NO_CHECK6_TX). This
triggered the skb_warn_bad_offload.
RIP: 0010:skb_warn_bad_offload+0x2bc/0x600 net/core/dev.c:2658
skb_gso_segment include/linux/netdevice.h:4038 [inline]
validate_xmit_skb+0x54d/0xd90 net/core/dev.c:3120
__dev_queue_xmit+0xbf8/0x34c0 net/core/dev.c:3577
dev_queue_xmit+0x17/0x20 net/core/dev.c:3618
UDP_NO_CHECK6_TX sets skb->ip_summed to CHECKSUM_NONE just after the
udp gso integrity checks in udp_(v6_)send_skb. Extend those checks to
catch and fail in this case.
After the integrity checks jump directly to the CHECKSUM_PARTIAL case
to avoid reading the no_check_tx flags again (a TOCTTOU race).
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow specifying segment size in the send call.
The new control message performs the same function as socket option
UDP_SEGMENT while avoiding the extra system call.
[ Export udp_cmsg_send for ipv6. -DaveM ]
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support generic segmentation offload for udp datagrams. Callers can
concatenate and send at once the payload of multiple datagrams with
the same destination.
To set segment size, the caller sets socket option UDP_SEGMENT to the
length of each discrete payload. This value must be smaller than or
equal to the relevant MTU.
A follow-up patch adds cmsg UDP_SEGMENT to specify segment size on a
per send call basis.
Total byte length may then exceed MTU. If not an exact multiple of
segment size, the last segment will be shorter.
The implementation adds a gso_size field to the udp socket, ip(v6)
cmsg cookie and inet_cork structure to be able to set the value at
setsockopt or cmsg time and to work with both lockless and corked
paths.
Initial benchmark numbers show UDP GSO about as expensive as TCP GSO.
tcp tso
3197 MB/s 54232 msg/s 54232 calls/s
6,457,754,262 cycles
tcp gso
1765 MB/s 29939 msg/s 29939 calls/s
11,203,021,806 cycles
tcp without tso/gso *
739 MB/s 12548 msg/s 12548 calls/s
11,205,483,630 cycles
udp
876 MB/s 14873 msg/s 624666 calls/s
11,205,777,429 cycles
udp gso
2139 MB/s 36282 msg/s 36282 calls/s
11,204,374,561 cycles
[*] after reverting commit 0a6b2a1dc2
("tcp: switch to GSO being always on")
Measured total system cycles ('-a') for one core while pinning both
the network receive path and benchmark process to that core:
perf stat -a -C 12 -e cycles \
./udpgso_bench_tx -C 12 -4 -D "$DST" -l 4
Note the reduction in calls/s with GSO. Bytes per syscall drops
increases from 1470 to 61818.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP segmentation offload needs access to inet_cork in the udp layer.
Pass the struct to ip(6)_make_skb instead of allocating it on the
stack in that function itself.
This patch is a noop otherwise.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-03-31
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add raw BPF tracepoint API in order to have a BPF program type that
can access kernel internal arguments of the tracepoints in their
raw form similar to kprobes based BPF programs. This infrastructure
also adds a new BPF_RAW_TRACEPOINT_OPEN command to BPF syscall which
returns an anon-inode backed fd for the tracepoint object that allows
for automatic detach of the BPF program resp. unregistering of the
tracepoint probe on fd release, from Alexei.
2) Add new BPF cgroup hooks at bind() and connect() entry in order to
allow BPF programs to reject, inspect or modify user space passed
struct sockaddr, and as well a hook at post bind time once the port
has been allocated. They are used in FB's container management engine
for implementing policy, replacing fragile LD_PRELOAD wrapper
intercepting bind() and connect() calls that only works in limited
scenarios like glibc based apps but not for other runtimes in
containerized applications, from Andrey.
3) BPF_F_INGRESS flag support has been added to sockmap programs for
their redirect helper call bringing it in line with cls_bpf based
programs. Support is added for both variants of sockmap programs,
meaning for tx ULP hooks as well as recv skb hooks, from John.
4) Various improvements on BPF side for the nfp driver, besides others
this work adds BPF map update and delete helper call support from
the datapath, JITing of 32 and 64 bit XADD instructions as well as
offload support of bpf_get_prandom_u32() call. Initial implementation
of nfp packet cache has been tackled that optimizes memory access
(see merge commit for further details), from Jakub and Jiong.
5) Removal of struct bpf_verifier_env argument from the print_bpf_insn()
API has been done in order to prepare to use print_bpf_insn() soon
out of perf tool directly. This makes the print_bpf_insn() API more
generic and pushes the env into private data. bpftool is adjusted
as well with the print_bpf_insn() argument removal, from Jiri.
6) Couple of cleanups and prep work for the upcoming BTF (BPF Type
Format). The latter will reuse the current BPF verifier log as
well, thus bpf_verifier_log() is further generalized, from Martin.
7) For bpf_getsockopt() and bpf_setsockopt() helpers, IPv4 IP_TOS read
and write support has been added in similar fashion to existing
IPv6 IPV6_TCLASS socket option we already have, from Nikita.
8) Fixes in recent sockmap scatterlist API usage, which did not use
sg_init_table() for initialization thus triggering a BUG_ON() in
scatterlist API when CONFIG_DEBUG_SG was enabled. This adds and
uses a small helper sg_init_marker() to properly handle the affected
cases, from Prashant.
9) Let the BPF core follow IDR code convention and therefore use the
idr_preload() and idr_preload_end() helpers, which would also help
idr_alloc_cyclic() under GFP_ATOMIC to better succeed under memory
pressure, from Shaohua.
10) Last but not least, a spelling fix in an error message for the
BPF cookie UID helper under BPF sample code, from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
== The problem ==
See description of the problem in the initial patch of this patch set.
== The solution ==
The patch provides much more reliable in-kernel solution for the 2nd
part of the problem: making outgoing connecttion from desired IP.
It adds new attach types `BPF_CGROUP_INET4_CONNECT` and
`BPF_CGROUP_INET6_CONNECT` for program type
`BPF_PROG_TYPE_CGROUP_SOCK_ADDR` that can be used to override both
source and destination of a connection at connect(2) time.
Local end of connection can be bound to desired IP using newly
introduced BPF-helper `bpf_bind()`. It allows to bind to only IP though,
and doesn't support binding to port, i.e. leverages
`IP_BIND_ADDRESS_NO_PORT` socket option. There are two reasons for this:
* looking for a free port is expensive and can affect performance
significantly;
* there is no use-case for port.
As for remote end (`struct sockaddr *` passed by user), both parts of it
can be overridden, remote IP and remote port. It's useful if an
application inside cgroup wants to connect to another application inside
same cgroup or to itself, but knows nothing about IP assigned to the
cgroup.
Support is added for IPv4 and IPv6, for TCP and UDP.
IPv4 and IPv6 have separate attach types for same reason as sys_bind
hooks, i.e. to prevent reading from / writing to e.g. user_ip6 fields
when user passes sockaddr_in since it'd be out-of-bound.
== Implementation notes ==
The patch introduces new field in `struct proto`: `pre_connect` that is
a pointer to a function with same signature as `connect` but is called
before it. The reason is in some cases BPF hooks should be called way
before control is passed to `sk->sk_prot->connect`. Specifically
`inet_dgram_connect` autobinds socket before calling
`sk->sk_prot->connect` and there is no way to call `bpf_bind()` from
hooks from e.g. `ip4_datagram_connect` or `ip6_datagram_connect` since
it'd cause double-bind. On the other hand `proto.pre_connect` provides a
flexible way to add BPF hooks for connect only for necessary `proto` and
call them at desired time before `connect`. Since `bpf_bind()` is
allowed to bind only to IP and autobind in `inet_dgram_connect` binds
only port there is no chance of double-bind.
bpf_bind() sets `force_bind_address_no_port` to bind to only IP despite
of value of `bind_address_no_port` socket field.
bpf_bind() sets `with_lock` to `false` when calling to __inet_bind()
and __inet6_bind() since all call-sites, where bpf_bind() is called,
already hold socket lock.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations just initialize udp4 defaults.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the udp_rmem_min, udp_wmem_min
to namespace and init the udp_l3mdev_accept explicitly.
The udp_rmem_min/udp_wmem_min affect udp rx/tx queue,
with this patch namespaces can set them differently.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since UDP-Lite is always using checksum, the following path is
triggered when calculating pseudo header for it:
udp4_csum_init() or udp6_csum_init()
skb_checksum_init_zero_check()
__skb_checksum_validate_complete()
The problem can appear if skb->len is less than CHECKSUM_BREAK. In
this particular case __skb_checksum_validate_complete() also invokes
__skb_checksum_complete(skb). If UDP-Lite is using partial checksum
that covers only part of a packet, the function will return bad
checksum and the packet will be dropped.
It can be fixed if we skip skb_checksum_init_zero_check() and only
set the required pseudo header checksum for UDP-Lite with partial
checksum before udp4_csum_init()/udp6_csum_init() functions return.
Fixes: ed70fcfcee ("net: Call skb_checksum_init in IPv4")
Fixes: e4f45b7f40 ("net: Call skb_checksum_init in IPv6")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arp_net_ops just addr/removes /proc entry.
devinet_ops allocates and frees duplicate of init_net tables
and (un)registers sysctl entries.
fib_net_ops allocates and frees pernet tables, creates/destroys
netlink socket and (un)initializes /proc entries. Foreign
pernet_operations do not touch them.
ip_rt_proc_ops only modifies pernet /proc entries.
xfrm_net_ops creates/destroys /proc entries, allocates/frees
pernet statistics, hashes and tables, and (un)initializes
sysctl files. These are not touched by foreigh pernet_operations
xfrm4_net_ops allocates/frees private pernet memory, and
configures sysctls.
sysctl_route_ops creates/destroys sysctls.
rt_genid_ops only initializes fields of just allocated net.
ipv4_inetpeer_ops allocated/frees net private memory.
igmp_net_ops just creates/destroys /proc files and socket,
noone else interested in.
tcp_sk_ops seems to be safe, because tcp_sk_init() does not
depend on any other pernet_operations modifications. Iteration
over hash table in inet_twsk_purge() is made under RCU lock,
and it's safe to iterate the table this way. Removing from
the table happen from inet_twsk_deschedule_put(), but this
function is safe without any extern locks, as it's synchronized
inside itself. There are many examples, it's used in different
context. So, it's safe to leave tcp_sk_exit_batch() unlocked.
tcp_net_metrics_ops is synchronized on tcp_metrics_lock and safe.
udplite4_net_ops only creates/destroys pernet /proc file.
icmp_sk_ops creates percpu sockets, not touched by foreign
pernet_operations.
ipmr_net_ops creates/destroys pernet fib tables, (un)registers
fib rules and /proc files. This seem to be safe to execute
in parallel with foreign pernet_operations.
af_inet_ops just sets up default parameters of newly created net.
ipv4_mib_ops creates and destroys pernet percpu statistics.
raw_net_ops, tcp4_net_ops, udp4_net_ops, ping_v4_net_ops
and ip_proc_ops only create/destroy pernet /proc files.
ip4_frags_ops creates and destroys sysctl file.
So, it's safe to make the pernet_operations async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Message sends to the local broadcast address (255.255.255.255) require
uc_index or sk_bound_dev_if to be set to an egress device. However,
responses or only received if the socket is bound to the device. This
is overly constraining for processes running in an L3 domain. This
patch allows a socket bound to the VRF device to send to the local
broadcast address by using IP_UNICAST_IF to set the egress interface
with packet receipt handled by the VRF binding.
Similar to IP_MULTICAST_IF, relax the constraint on setting
IP_UNICAST_IF if a socket is bound to an L3 master device. In this
case allow uc_index to be set to an enslaved if sk_bound_dev_if is
an L3 master device and is the master device for the ifindex.
In udp and raw sendmsg, allow uc_index to override the oif if
uc_index master device is oif (ie., the oif is an L3 master and the
index is an L3 slave).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc has been ignoring struct file_operations::owner field for 10 years.
Specifically, it started with commit 786d7e1612
("Fix rmmod/read/write races in /proc entries"). Notice the chunk where
inode->i_fop is initialized with proxy struct file_operations for
regular files:
- if (de->proc_fops)
- inode->i_fop = de->proc_fops;
+ if (de->proc_fops) {
+ if (S_ISREG(inode->i_mode))
+ inode->i_fop = &proc_reg_file_ops;
+ else
+ inode->i_fop = de->proc_fops;
+ }
VFS stopped pinning module at this point.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On multi-threaded processes, one common architecture is to have
one (or a small number of) threads polling sockets, and a
considerably larger pool of threads reading form and writing to the
sockets. When we set RPS core on tcp_poll() or udp_poll() we essentially
steer all packets of all the polled FDs to one (or small number of)
cores, creaing a bottleneck and/or RPS misprediction.
Another common architecture is to shard FDs among threads pinned
to cores. In such a setting, setting RPS core in tcp_poll() and
udp_poll() is redundant because the RFS core is correctly
set in recvmsg and sendmsg.
Thus, revert the following commit:
c3f1dbaf6e ("net: Update RFS target at poll for tcp/udp").
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the udp[46]_portaddr_hash()
to net/ip[v6].h. The function name is renamed to
ipv[46]_portaddr_hash().
It will be used by a later patch which adds a second listener
hashtable hashed by the address and port.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit e32ea7e747 ("soreuseport: fast reuseport UDP socket
selection") and commit c125e80b88 ("soreuseport: fast reuseport
TCP socket selection") the relevant reuseport socket matching the current
packet is selected by the reuseport_select_sock() call. The only
exceptions are invalid BPF filters/filters returning out-of-range
indices.
In the latter case the code implicitly falls back to using the hash
demultiplexing, but instead of selecting the socket inside the
reuseport_select_sock() function, it relies on the hash selection
logic introduced with the early soreuseport implementation.
With this patch, in case of a BPF filter returning a bad socket
index value, we fall back to hash-based selection inside the
reuseport_select_sock() body, so that we can drop some duplicate
code in the ipv4 and ipv6 stack.
This also allows faster lookup in the above scenario and will allow
us to avoid computing the hash value for successful, BPF based
demultiplexing - in a later patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller stumbled upon a way to trigger
WARNING: CPU: 1 PID: 13881 at net/core/sock_reuseport.c:41
reuseport_alloc+0x306/0x3b0 net/core/sock_reuseport.c:39
There are two initialization paths for the sock_reuseport structure in a
socket: Through the udp/tcp bind paths of SO_REUSEPORT sockets or through
SO_ATTACH_REUSEPORT_[CE]BPF before bind. The existing implementation
assumedthat the socket lock protected both of these paths when it actually
only protects the SO_ATTACH_REUSEPORT path. Syzkaller triggered this
double allocation by running these paths concurrently.
This patch moves the check for double allocation into the reuseport_alloc
function which is protected by a global spin lock.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Fixes: c125e80b88 ("soreuseport: fast reuseport TCP socket selection")
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the UDP code there are two leftover error messages with very few meaning.
Replace them with a more descriptive error message as some users
reported them as "strange network error".
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit bc044e8db7 ("udp: perform source validation for
mcast early demux") does not take into account that broadcast packets
lands in the same code path and they need different checks for the
source address - notably, zero source address are valid for bcast
and invalid for mcast.
As a result, 2nd and later broadcast packets with 0 source address
landing to the same socket are dropped. This breaks dhcp servers.
Since we don't have stringent performance requirements for ingress
broadcast traffic, fix it by disabling UDP early demux such traffic.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Fixes: bc044e8db7 ("udp: perform source validation for mcast early demux")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP early demux can leverate the rx dst cache even for
multicast unconnected sockets.
In such scenario the ipv4 source address is validated only on
the first packet in the given flow. After that, when we fetch
the dst entry from the socket rx cache, we stop enforcing
the rp_filter and we even start accepting any kind of martian
addresses.
Disabling the dst cache for unconnected multicast socket will
cause large performace regression, nearly reducing by half the
max ingress tput.
Instead we factor out a route helper to completely validate an
skb source address for multicast packets and we call it from
the UDP early demux for mcast packets landing on unconnected
sockets, after successful fetching the related cached dst entry.
This still gives a measurable, but limited performance
regression:
rp_filter = 0 rp_filter = 1
edmux disabled: 1182 Kpps 1127 Kpps
edmux before: 2238 Kpps 2238 Kpps
edmux after: 2037 Kpps 2019 Kpps
The above figures are on top of current net tree.
Applying the net-next commit 6e617de84e ("net: avoid a full
fib lookup when rp_filter is disabled.") the delta with
rp_filter == 0 will decrease even more.
Fixes: 421b3885bf ("udp: ipv4: Add udp early demux")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently no error is emitted, but this infrastructure will
used by the next patch to allow source address validation
for mcast sockets.
Since early demux can do a route lookup and an ipv4 route
lookup can return an error code this is consistent with the
current ipv4 route infrastructure.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 6b229cf77d ("udp: add batching to udp_rmem_release()")
reduced greatly the cacheline contention between the BH and the US
reader batching the rmem updates in most scenarios.
Such optimization is explicitly avoided if the US reader is faster
then BH processing.
My fault, I initially suggested this kind of behavior due to concerns
of possible regressions with small sk_rcvbuf values. Tests showed
such concerns are misplaced, so this commit relaxes the condition
for rmem bulk updates, obtaining small but measurable performance
gain in the scenario described above.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 0ddf3fb2c4 ("udp: preserve skb->dst if required
for IP options processing") we clear the skb head state as soon
as the skb carrying them is first processed.
Since the same skb can be processed several times when MSG_PEEK
is used, we can end up lacking the required head states, and
eventually oopsing.
Fix this clearing the skb head state only when processing the
last skb reference.
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 0ddf3fb2c4 ("udp: preserve skb->dst if required for IP options processing")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
After commit dce4551cb2 ("udp: preserve head state for IP_CMSG_PASSSEC")
we preserve the secpath for the whole skb lifecycle, but we also
end up leaking a reference to it.
We must clear the head state on skb reception, if secpath is
present.
Fixes: dce4551cb2 ("udp: preserve head state for IP_CMSG_PASSSEC")
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in the udp6 code, the dst cookie is not initialized/updated
concurrently with the RX dst used by early demux.
As a result, the dst_check() in the early_demux path always fails,
the rx dst cache is always invalidated, and we can't really
leverage significant gain from the demux lookup.
Fix it adding udp6 specific variant of sk_rx_dst_set() and use it
to set the dst cookie when the dst entry is really changed.
The issue is there since the introduction of early demux for ipv6.
Fixes: 5425077d73 ("net: ipv6: Add early demux handler for UDP unicast")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove two references to ufo in the udp send path that are no longer
reachable now that ufo has been removed.
Commit 85f1bd9a7b ("udp: consistently apply ufo or fragmentation")
is a fix to ufo. It is safe to revert what remains of it.
Also, no skb can enter ip_append_page with skb_is_gso true now that
skb_shinfo(skb)->gso_type is no longer set in ip_append_page/_data.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to commit e6afc8ace6 ("udp: remove
headers from UDP packets before queueing"), when udp packets are being
peeked the requested extra offset is always 0 as there is no need to skip
the udp header. However, when the offset is 0 and the next skb is
of length 0, it is only returned once. The behaviour can be seen with
the following python script:
from socket import *;
f=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
g=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
f.bind(('::', 0));
addr=('::1', f.getsockname()[1]);
g.sendto(b'', addr)
g.sendto(b'b', addr)
print(f.recvfrom(10, MSG_PEEK));
print(f.recvfrom(10, MSG_PEEK));
Where the expected output should be the empty string twice.
Instead, make sk_peek_offset return negative values, and pass those values
to __skb_try_recv_datagram/__skb_try_recv_from_queue. If the passed offset
to __skb_try_recv_from_queue is negative, the checked skb is never skipped.
__skb_try_recv_from_queue will then ensure the offset is reset back to 0
if a peek is requested without an offset, unless no packets are found.
Also simplify the if condition in __skb_try_recv_from_queue. If _off is
greater then 0, and off is greater then or equal to skb->len, then
(_off || skb->len) must always be true assuming skb->len >= 0 is always
true.
Also remove a redundant check around a call to sk_peek_offset in af_unix.c,
as it double checked if MSG_PEEK was set in the flags.
V2:
- Moved the negative fixup into __skb_try_recv_from_queue, and remove now
redundant checks
- Fix peeking in udp{,v6}_recvmsg to report the right value when the
offset is 0
V3:
- Marked new branch in __skb_try_recv_from_queue as unlikely.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/linux/mm_types.h
mm/huge_memory.c
I removed the smp_mb__before_spinlock() like the following commit does:
8b1b436dd1 ("mm, locking: Rework {set,clear,mm}_tlb_flush_pending()")
and fixed up the affected commits.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mainline had UFO fixes, but UFO is removed in net-next so we
take the HEAD hunks.
Minor context conflict in bcmsysport statistics bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
When iteratively building a UDP datagram with MSG_MORE and that
datagram exceeds MTU, consistently choose UFO or fragmentation.
Once skb_is_gso, always apply ufo. Conversely, once a datagram is
split across multiple skbs, do not consider ufo.
Sendpage already maintains the first invariant, only add the second.
IPv6 does not have a sendpage implementation to modify.
A gso skb must have a partial checksum, do not follow sk_no_check_tx
in udp_send_skb.
Found by syzkaller.
Fixes: e89e9cf539 ("[IPv4/IPv6]: UFO Scatter-gather approach")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any use of key->enabled (that is static_key_enabled and static_key_count)
outside jump_label_lock should handle its own serialization. The only
two that are not doing so are the UDP encapsulation static keys. Change
them to use static_key_enable, which now correctly tests key->enabled under
the jump label lock.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1501601046-35683-3-git-send-email-pbonzini@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a second device index, sdif, to inet socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
TCP moves the data in the cb. Prior to tcp_v4_rcv (e.g., early demux) the
ingress index is obtained from IPCB using inet_sdif and after the cb move
in tcp_v4_rcv the tcp_v4_sdif helper is used.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a second device index, sdif, to udp socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
Early demux lookups are handled in the next patch as part of INET_MATCH
changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ip_options_echo() does not need anymore skb->dst, so we can
avoid explicitly preserving it for its own sake.
This is almost a revert of commit 0ddf3fb2c4 ("udp: preserve
skb->dst if required for IP options processing") plus some
lifting to fit later changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an early demuxed packet reaches __udp6_lib_lookup_skb(), the
sk reference is retrieved and used, but the relevant reference
count is leaked and the socket destructor is never called.
Beyond leaking the sk memory, if there are pending UDP packets
in the receive queue, even the related accounted memory is leaked.
In the long run, this will cause persistent forward allocation errors
and no UDP skbs (both ipv4 and ipv6) will be able to reach the
user-space.
Fix this by explicitly accessing the early demux reference before
the lookup, and properly decreasing the socket reference count
after usage.
Also drop the skb_steal_sock() in __udp6_lib_lookup_skb(), and
the now obsoleted comment about "socket cache".
The newly added code is derived from the current ipv4 code for the
similar path.
v1 -> v2:
fixed the __udp6_lib_rcv() return code for resubmission,
as suggested by Eric
Reported-by: Sam Edwards <CFSworks@gmail.com>
Reported-by: Marc Haber <mh+netdev@zugschlus.de>
Fixes: 5425077d73 ("net: ipv6: Add early demux handler for UDP unicast")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must use pre-processor conditional block or suitable accessors to
manipulate skb->sp elsewhere builds lacking the CONFIG_XFRM will break.
Fixes: dce4551cb2 ("udp: preserve head state for IP_CMSG_PASSSEC")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore reported a SELinux/IP_PASSSEC regression
caused by missing skb->sp at recvmsg() time. We need to
preserve the skb head state to process the IP_CMSG_PASSSEC
cmsg.
With this commit we avoid releasing the skb head state in the
BH even if a secpath is attached to the current skb, and stores
the skb status (with/without head states) in the scratch area,
so that we can access it at skb deallocation time, without
incurring in cache-miss penalties.
This also avoids misusing the skb CB for ipv6 packets,
as introduced by the commit 0ddf3fb2c4 ("udp: preserve
skb->dst if required for IP options processing").
Clean a bit the scratch area helpers implementation, to
reduce the code differences between 32 and 64 bits build.
Reported-by: Paul Moore <paul@paul-moore.com>
Fixes: 0a463c78d2 ("udp: avoid a cache miss on dequeue")
Fixes: 0ddf3fb2c4 ("udp: preserve skb->dst if required for IP options processing")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric noticed that in udp_recvmsg() we still need to access
skb->dst while processing the IP options.
Since commit 0a463c78d2 ("udp: avoid a cache miss on dequeue")
skb->dst is no more available at recvmsg() time and bad things
will happen if we enter the relevant code path.
This commit address the issue, avoid clearing skb->dst if
any IP options are present into the relevant skb.
Since the IP CB is contained in the first skb cacheline, we can
test it to decide to leverage the consume_stateless_skb()
optimization, without measurable additional cost in the faster
path.
v1 -> v2: updated commit message tags
Fixes: 0a463c78d2 ("udp: avoid a cache miss on dequeue")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
This patch uses refcount_inc_not_zero() instead of
atomic_inc_not_zero_hint() due to absense of a _hint()
version of refcount API. If the hint() version must
be used, we might need to revisit API.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that they can be later used by the IPv6 code, too.
Also lift the comments a bit.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael reported an UDP breakage caused by the commit b65ac44674
("udp: try to avoid 2 cache miss on dequeue").
The function __first_packet_length() can update the checksum bits
of the pending skb, making the scratched area out-of-sync, and
setting skb->csum, if the skb was previously in need of checksum
validation.
On later recvmsg() for such skb, checksum validation will be
invoked again - due to the wrong udp_skb_csum_unnecessary()
value - and will fail, causing the valid skb to be dropped.
This change addresses the issue refreshing the scratch area in
__first_packet_length() after the possible checksum update.
Fixes: b65ac44674 ("udp: try to avoid 2 cache miss on dequeue")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On UDP packets processing, if the BH is the bottle-neck, it
always sees a cache miss while updating rmem_alloc; try to
avoid it prefetching the value as soon as we have the socket
available.
Performances under flood with multiple NIC rx queues used are
unaffected, but when a single NIC rx queue is in use, this
gives ~10% performance improvement.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In udp_v4/6_early_demux() code, we try to hold dst->__refcnt for
dst with DST_NOCACHE flag. This is because later in udp_sk_rx_dst_set()
function, we will try to cache this dst in sk for connected case.
However, a better way to achieve this is to not try to hold dst in
early_demux(), but in udp_sk_rx_dst_set(), call dst_hold_safe(). This
approach is also more consistant with how tcp is handling it. And it
will make later changes simpler.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when udp_recvmsg() is executed, on x86_64 and other archs, most skb
fields are on cold cachelines.
If the skb are linear and the kernel don't need to compute the udp
csum, only a handful of skb fields are required by udp_recvmsg().
Since we already use skb->dev_scratch to cache hot data, and
there are 32 bits unused on 64 bit archs, use such field to cache
as much data as we can, and try to prefetch on dequeue the relevant
fields that are left out.
This can save up to 2 cache miss per packet.
v1 -> v2:
- changed udp_dev_scratch fields types to u{32,16} variant,
replaced bitfiled with bool
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since UDP no more uses sk->destructor, we can clear completely
the skb head state before enqueuing. Amend and use
skb_release_head_state() for that.
All head states share a single cacheline, which is not
normally used/accesses on dequeue. We can avoid entirely accessing
such cacheline implementing and using in the UDP code a specialized
skb free helper which ignores the skb head state.
This saves a cacheline miss at skb deallocation time.
v1 -> v2:
replaced secpath_reset() with skb_release_head_state()
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function has to return NULL on a error case, because there is a
separate error variable.
The offset has to be changed only if skb is returned
v2: fix udp code to not use an extra variable
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Fixes: 65101aeca5 ("net/sock: factor out dequeue/peek with offset cod")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the udp memory accounting refactor, we don't need any more
to export the *udp*_queue_rcv_skb(). Make them static and fix
a couple of sparse warnings:
net/ipv4/udp.c:1615:5: warning: symbol 'udp_queue_rcv_skb' was not
declared. Should it be static?
net/ipv6/udp.c:572:5: warning: symbol 'udpv6_queue_rcv_skb' was not
declared. Should it be static?
Fixes: 850cbaddb5 ("udp: use it's own memory accounting schema")
Fixes: c915fe13cb ("udplite: fix NULL pointer dereference")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function udp_skb_dtor_locked does not need to be in global scope
so make it static to fix sparse warning:
net/ipv4/udp.c: warning: symbol 'udp_skb_dtor_locked' was not
declared. Should it be static?
Fixes: 6dfb4367cd ("udp: keep the sk_receive_queue held when splicing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On packet reception, when we are forced to splice the
sk_receive_queue, we can keep the related lock held, so
that we can avoid re-acquiring it, if fwd memory
scheduling is required.
v1 -> v2:
the rx_queue_lock_held param in udp_rmem_release() is
now a bool
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
under udp flood the sk_receive_queue spinlock is heavily contended.
This patch try to reduce the contention on such lock adding a
second receive queue to the udp sockets; recvmsg() looks first
in such queue and, only if empty, tries to fetch the data from
sk_receive_queue. The latter is spliced into the newly added
queue every time the receive path has to acquire the
sk_receive_queue lock.
The accounting of forward allocated memory is still protected with
the sk_receive_queue lock, so udp_rmem_release() needs to acquire
both locks when the forward deficit is flushed.
On specific scenarios we can end up acquiring and releasing the
sk_receive_queue lock multiple times; that will be covered by
the next patch
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The datagram protocols can use MSG_CONFIRM to confirm the
neighbour. When used with MSG_PROBE we do not reach the
code where neighbour is confirmed, so we have to do the
same slow lookup by using the dst_confirm_neigh() helper.
When MSG_PROBE is not used, ip_append_data/ip6_append_data
will set the skb flag dst_pending_confirm.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8 ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf3 ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry reported that UDP sockets being destroyed would trigger the
WARN_ON(atomic_read(&sk->sk_rmem_alloc)); in inet_sock_destruct()
It turns out we do not properly destroy skb(s) that have wrong UDP
checksum.
Thanks again to syzkaller team.
Fixes : 7c13f97ffd ("udp: do fwd memory scheduling on dequeue")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets arriving in a VRF currently are delivered to UDP sockets that
aren't bound to any interface. TCP defaults to not delivering packets
arriving in a VRF to unbound sockets. IP route lookup and socket
transmit both assume that unbound means using the default table and
UDP applications that haven't been changed to be aware of VRFs may not
function correctly in this case since they may not be able to handle
overlapping IP address ranges, or be able to send packets back to the
original sender if required.
So add a sysctl, udp_l3mdev_accept, to control this behaviour with it
being analgous to the existing tcp_l3mdev_accept, namely to allow a
process to have a VRF-global listen socket. Have this default to off
as this is the behaviour that users will expect, given that there is
no explicit mechanism to set unmodified VRF-unaware application into a
default VRF.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We pass these per-protocol equal functions around in various places, but
we can just have one function that checks the sk->sk_family and then do
the right comparison function. I've also changed the ipv4 version to
not cast to inet_sock since it is unneeded.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP lib inuse checks will walk the entire hash bucket to check if the
portaddr is in use. In the case of reuseport we can stop searching when
we find a matching reuseport.
On a 16-core VM a test program that spawns 16 threads that each bind to
1024 sockets (one per 10ms) takes 1m45s. With this change it takes 11s.
Also add a cond_resched() when the port is not specified.
Signed-off-by: Eric Garver <e@erig.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In flood situations, keeping sk_rmem_alloc at a high value
prevents producers from touching the socket.
It makes sense to lower sk_rmem_alloc only at the end
of udp_rmem_release() after the thread draining receive
queue in udp_recvmsg() finished the writes to sk_forward_alloc.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If udp_recvmsg() constantly releases sk_rmem_alloc
for every read packet, it gives opportunity for
producers to immediately grab spinlocks and desperatly
try adding another packet, causing false sharing.
We can add a simple heuristic to give the signal
by batches of ~25 % of the queue capacity.
This patch considerably increases performance under
flood by about 50 %, since the thread draining the queue
is no longer slowed by false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In UDP RX handler, we currently clear skb->dev before skb
is added to receive queue, because device pointer is no longer
available once we exit from RCU section.
Since this first cache line is always hot, lets reuse this space
to store skb->truesize and thus avoid a cache line miss at
udp_recvmsg()/udp_skb_destructor time while receive queue
spinlock is held.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Idea of busylocks is to let producers grab an extra spinlock
to relieve pressure on the receive_queue spinlock shared by consumer.
This behavior is requested only once socket receive queue is above
half occupancy.
Under flood, this means that only one producer can be in line
trying to acquire the receive_queue spinlock.
These busylock can be allocated on a per cpu manner, instead of a
per socket one (that would consume a cache line per socket)
This patch considerably improves UDP behavior under stress,
depending on number of NIC RX queues and/or RPS spread.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under UDP flood, many softirq producers try to add packets to
UDP receive queue, and one user thread is burning one cpu trying
to dequeue packets as fast as possible.
Two parts of the per packet cost are :
- copying payload from kernel space to user space,
- freeing memory pieces associated with skb.
If socket is under pressure, softirq handler(s) can try to pull in
skb->head the payload of the packet if it fits.
Meaning the softirq handler(s) can free/reuse the page fragment
immediately, instead of letting udp_recvmsg() do this hundreds of usec
later, possibly from another node.
Additional gains :
- We reduce skb->truesize and thus can store more packets per SO_RCVBUF
- We avoid cache line misses at copyout() time and consume_skb() time,
and avoid one put_page() with potential alien freeing on NUMA hosts.
This comes at the cost of a copy, bounded to available tail room, which
is usually small. (We might have to fix GRO_MAX_HEAD which looks bigger
than necessary)
This patch gave me about 5 % increase in throughput in my tests.
skb_condense() helper could probably used in other contexts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 850cbaddb5 ("udp: use it's own memory accounting
schema"), the udp protocol allowed sk_rmem_alloc to grow beyond
the rcvbuf by the whole current packet's truesize. After said commit
we allow sk_rmem_alloc to exceed the rcvbuf only if the receive queue
is empty. As reported by Jesper this cause a performance regression
for some (small) values of rcvbuf.
This commit is intended to fix the regression restoring the old
handling of the rcvbuf limit.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Fixes: 850cbaddb5 ("udp: use it's own memory accounting schema")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commits 93821778de ("udp: Fix rcv socket locking") and
f7ad74fef3 ("net/ipv6/udp: UDP encapsulation: break backlog_rcv into
__udpv6_queue_rcv_skb") UDP backlog handlers were renamed, but UDPlite
was forgotten.
This leads to crashes if UDPlite header is pulled twice, which happens
starting from commit e6afc8ace6 ("udp: remove headers from UDP packets
before queueing")
Bug found by syzkaller team, thanks a lot guys !
Note that backlog use in UDP/UDPlite is scheduled to be removed starting
from linux-4.10, so this patch is only needed up to linux-4.9
Fixes: 93821778de ("udp: Fix rcv socket locking")
Fixes: f7ad74fef3 ("net/ipv6/udp: UDP encapsulation: break backlog_rcv into __udpv6_queue_rcv_skb")
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP_SKB_CB(skb)->partial_cov is located at offset 66 in skb,
requesting a cold cache line being read in cpu cache.
We can avoid this cache line miss for UDP sockets,
as partial_cov has a meaning only for UDPLite.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP busy polling is restricted to connected UDP sockets.
This is because sk_busy_loop() only takes care of one NAPI context.
There are cases where it could be extended.
1) Some hosts receive traffic on a single NIC, with one RX queue.
2) Some applications use SO_REUSEPORT and associated BPF filter
to split the incoming traffic on one UDP socket per RX
queue/thread/cpu
3) Some UDP sockets are used to send/receive traffic for one flow, but
they do not bother with connect()
This patch records the napi_id of first received skb, giving more
reach to busy polling.
Tested:
lpaa23:~# echo 70 >/proc/sys/net/core/busy_read
lpaa24:~# echo 70 >/proc/sys/net/core/busy_read
lpaa23:~# for f in `seq 1 10`; do ./super_netperf 1 -H lpaa24 -t UDP_RR -l 5; done
Before patch :
27867 28870 37324 41060 41215
36764 36838 44455 41282 43843
After patch :
73920 73213 70147 74845 71697
68315 68028 75219 70082 73707
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Honor udptable parameter that is passed to __udp*_lib_mcast_deliver(),
otherwise udplite broadcast/multicast use the wrong table and it breaks.
Fixes: 2dc41cff75 ("udp: Use hash2 for long hash1 chains in __udp*_lib_mcast_deliver.")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 850cbaddb5 ("udp: use it's own memory accounting schema")
assumes that the socket proto has memory accounting enabled,
but this is not the case for UDPLITE.
Fix it enabling memory accounting for UDPLITE and performing
fwd allocated memory reclaiming on socket shutdown.
UDP and UDPLITE share now the same memory accounting limits.
Also drop the backlog receive operation, since is no more needed.
Fixes: 850cbaddb5 ("udp: use it's own memory accounting schema")
Reported-by: Andrei Vagin <avagin@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains a second batch of Netfilter updates for
your net-next tree. This includes a rework of the core hook
infrastructure that improves Netfilter performance by ~15% according to
synthetic benchmarks. Then, a large batch with ipset updates, including
a new hash:ipmac set type, via Jozsef Kadlecsik. This also includes a
couple of assorted updates.
Regarding the core hook infrastructure rework to improve performance,
using this simple drop-all packets ruleset from ingress:
nft add table netdev x
nft add chain netdev x y { type filter hook ingress device eth0 priority 0\; }
nft add rule netdev x y drop
And generating traffic through Jesper Brouer's
samples/pktgen/pktgen_bench_xmit_mode_netif_receive.sh script using -i
option. perf report shows nf_tables calls in its top 10:
17.30% kpktgend_0 [nf_tables] [k] nft_do_chain
15.75% kpktgend_0 [kernel.vmlinux] [k] __netif_receive_skb_core
10.39% kpktgend_0 [nf_tables_netdev] [k] nft_do_chain_netdev
I'm measuring here an improvement of ~15% in performance with this
patchset, so we got +2.5Mpps more. I have used my old laptop Intel(R)
Core(TM) i5-3320M CPU @ 2.60GHz 4-cores.
This rework contains more specifically, in strict order, these patches:
1) Remove compile-time debugging from core.
2) Remove obsolete comments that predate the rcu era. These days it is
well known that a Netfilter hook always runs under rcu_read_lock().
3) Remove threshold handling, this is only used by br_netfilter too.
We already have specific code to handle this from br_netfilter,
so remove this code from the core path.
4) Deprecate NF_STOP, as this is only used by br_netfilter.
5) Place nf_state_hook pointer into xt_action_param structure, so
this structure fits into one single cacheline according to pahole.
This also implicit affects nftables since it also relies on the
xt_action_param structure.
6) Move state->hook_entries into nf_queue entry. The hook_entries
pointer is only required by nf_queue(), so we can store this in the
queue entry instead.
7) use switch() statement to handle verdict cases.
8) Remove hook_entries field from nf_hook_state structure, this is only
required by nf_queue, so store it in nf_queue_entry structure.
9) Merge nf_iterate() into nf_hook_slow() that results in a much more
simple and readable function.
10) Handle NF_REPEAT away from the core, so far the only client is
nf_conntrack_in() and we can restart the packet processing using a
simple goto to jump back there when the TCP requires it.
This update required a second pass to fix fallout, fix from
Arnd Bergmann.
11) Set random seed from nft_hash when no seed is specified from
userspace.
12) Simplify nf_tables expression registration, in a much smarter way
to save lots of boiler plate code, by Liping Zhang.
13) Simplify layer 4 protocol conntrack tracker registration, from
Davide Caratti.
14) Missing CONFIG_NF_SOCKET_IPV4 dependency for udp4_lib_lookup, due
to recent generalization of the socket infrastructure, from Arnd
Bergmann.
15) Then, the ipset batch from Jozsef, he describes it as it follows:
* Cleanup: Remove extra whitespaces in ip_set.h
* Cleanup: Mark some of the helpers arguments as const in ip_set.h
* Cleanup: Group counter helper functions together in ip_set.h
* struct ip_set_skbinfo is introduced instead of open coded fields
in skbinfo get/init helper funcions.
* Use kmalloc() in comment extension helper instead of kzalloc()
because it is unnecessary to zero out the area just before
explicit initialization.
* Cleanup: Split extensions into separate files.
* Cleanup: Separate memsize calculation code into dedicated function.
* Cleanup: group ip_set_put_extensions() and ip_set_get_extensions()
together.
* Add element count to hash headers by Eric B Munson.
* Add element count to all set types header for uniform output
across all set types.
* Count non-static extension memory into memsize calculation for
userspace.
* Cleanup: Remove redundant mtype_expire() arguments, because
they can be get from other parameters.
* Cleanup: Simplify mtype_expire() for hash types by removing
one level of intendation.
* Make NLEN compile time constant for hash types.
* Make sure element data size is a multiple of u32 for the hash set
types.
* Optimize hash creation routine, exit as early as possible.
* Make struct htype per ipset family so nets array becomes fixed size
and thus simplifies the struct htype allocation.
* Collapse same condition body into a single one.
* Fix reported memory size for hash:* types, base hash bucket structure
was not taken into account.
* hash:ipmac type support added to ipset by Tomasz Chilinski.
* Use setup_timer() and mod_timer() instead of init_timer()
by Muhammad Falak R Wani, individually for the set type families.
16) Remove useless connlabel field in struct netns_ct, patch from
Florian Westphal.
17) xt_find_table_lock() doesn't return ERR_PTR() anymore, so simplify
{ip,ip6,arp}tables code that uses this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ca065d0cf8 ("udp: no longer use SLAB_DESTROY_BY_RCU")
the udp6_lib_lookup and udp4_lib_lookup functions are only
provided when it is actually possible to call them.
However, moving the callers now caused a link error:
net/built-in.o: In function `nf_sk_lookup_slow_v6':
(.text+0x131a39): undefined reference to `udp6_lib_lookup'
net/ipv4/netfilter/nf_socket_ipv4.o: In function `nf_sk_lookup_slow_v4':
nf_socket_ipv4.c:(.text.nf_sk_lookup_slow_v4+0x114): undefined reference to `udp4_lib_lookup'
This extends the #ifdef so we also provide the functions when
CONFIG_NF_SOCKET_IPV4 or CONFIG_NF_SOCKET_IPV6, respectively
are set.
Fixes: 8db4c5be88 ("netfilter: move socket lookup infrastructure to nf_socket_ipv{4,6}.c")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A new argument is added to __skb_recv_datagram to provide
an explicit skb destructor, invoked under the receive queue
lock.
The UDP protocol uses such argument to perform memory
reclaiming on dequeue, so that the UDP protocol does not
set anymore skb->desctructor.
Instead explicit memory reclaiming is performed at close() time and
when skbs are removed from the receive queue.
The in kernel UDP protocol users now need to call a
skb_recv_udp() variant instead of skb_recv_datagram() to
properly perform memory accounting on dequeue.
Overall, this allows acquiring only once the receive queue
lock on dequeue.
Tested using pktgen with random src port, 64 bytes packet,
wire-speed on a 10G link as sender and udp_sink as the receiver,
using an l4 tuple rxhash to stress the contention, and one or more
udp_sink instances with reuseport.
nr sinks vanilla patched
1 440 560
3 2150 2300
6 3650 3800
9 4450 4600
12 6250 6450
v1 -> v2:
- do rmem and allocated memory scheduling under the receive lock
- do bulk scheduling in first_packet_length() and in udp_destruct_sock()
- avoid the typdef for the dequeue callback
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can use it even after orphaining the skbuff.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the UID in routing lookups made by protocol connect() and
sendmsg() functions.
- Make sure that routing lookups triggered by incoming packets
(e.g., Path MTU discovery) take the UID of the socket into
account.
- For packets not associated with a userspace socket, (e.g., ping
replies) use UID 0 inside the user namespace corresponding to
the network namespace the socket belongs to. This allows
all namespaces to apply routing and iptables rules to
kernel-originated traffic in that namespaces by matching UID 0.
This is better than using the UID of the kernel socket that is
sending the traffic, because the UID of kernel sockets created
at namespace creation time (e.g., the per-processor ICMP and
TCP sockets) is the UID of the user that created the socket,
which might not be mapped in the namespace.
Tested: compiles allnoconfig, allyesconfig, allmodconfig
Tested: https://android-review.googlesource.com/253302
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
First bug was added in commit ad6f939ab1 ("ip: Add offset parameter to
ip_cmsg_recv") : Tom missed that ipv4 udp messages could be received on
AF_INET6 socket. ip_cmsg_recv(msg, skb) should have been replaced by
ip_cmsg_recv_offset(msg, skb, sizeof(struct udphdr));
Then commit e6afc8ace6 ("udp: remove headers from UDP packets before
queueing") forgot to adjust the offsets now UDP headers are pulled
before skb are put in receive queue.
Fixes: ad6f939ab1 ("ip: Add offset parameter to ip_cmsg_recv")
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completely avoid default sock memory accounting and replace it
with udp-specific accounting.
Since the new memory accounting model encapsulates completely
the required locking, remove the socket lock on both enqueue and
dequeue, and avoid using the backlog on enqueue.
Be sure to clean-up rx queue memory on socket destruction, using
udp its own sk_destruct.
Tested using pktgen with random src port, 64 bytes packet,
wire-speed on a 10G link as sender and udp_sink as the receiver,
using an l4 tuple rxhash to stress the contention, and one or more
udp_sink instances with reuseport.
nr readers Kpps (vanilla) Kpps (patched)
1 170 440
3 1250 2150
6 3000 3650
9 4200 4450
12 5700 6250
v4 -> v5:
- avoid unneeded test in first_packet_length
v3 -> v4:
- remove useless sk_rcvqueues_full() call
v2 -> v3:
- do not set the now unsed backlog_rcv callback
v1 -> v2:
- add memory pressure support
- fixed dropwatch accounting for ipv6
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid using the generic helpers.
Use the receive queue spin lock to protect the memory
accounting operation, both on enqueue and on dequeue.
On dequeue perform partial memory reclaiming, trying to
leave a quantum of forward allocated memory.
On enqueue use a custom helper, to allow some optimizations:
- use a plain spin_lock() variant instead of the slightly
costly spin_lock_irqsave(),
- avoid dst_force check, since the calling code has already
dropped the skb dst
- avoid orphaning the skb, since skb_steal_sock() already did
the work for us
The above needs custom memory reclaiming on shutdown, provided
by the udp_destruct_sock().
v5 -> v6:
- don't orphan the skb on enqueue
v4 -> v5:
- replace the mem_lock with the receive queue spin lock
- ensure that the bh is always allowed to enqueue at least
a skb, even if sk_rcvbuf is exceeded
v3 -> v4:
- reworked memory accunting, simplifying the schema
- provide an helper for both memory scheduling and enqueuing
v1 -> v2:
- use a udp specific destrctor to perform memory reclaiming
- remove a couple of helpers, unneeded after the above cleanup
- do not reclaim memory on dequeue if not under memory
pressure
- reworked the fwd accounting schema to avoid potential
integer overflow
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Baozeng Ding reported KASAN traces showing uses after free in
udp_lib_get_port() and other related UDP functions.
A CONFIG_DEBUG_PAGEALLOC=y kernel would eventually crash.
I could write a reproducer with two threads doing :
static int sock_fd;
static void *thr1(void *arg)
{
for (;;) {
connect(sock_fd, (const struct sockaddr *)arg,
sizeof(struct sockaddr_in));
}
}
static void *thr2(void *arg)
{
struct sockaddr_in unspec;
for (;;) {
memset(&unspec, 0, sizeof(unspec));
connect(sock_fd, (const struct sockaddr *)&unspec,
sizeof(unspec));
}
}
Problem is that udp_disconnect() could run without holding socket lock,
and this was causing list corruptions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we no longer use SLAB_DESTROY_BY_RCU for UDP,
we do not need sk_prot_clear_portaddr_nulls() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements SOCK_DESTROY for UDP sockets similar to what was done
for TCP with commit c1e64e298b ("net: diag: Support destroying TCP
sockets.") A process with a UDP socket targeted for destroy is awakened
and recvmsg fails with ECONNABORTED.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit ca065d0cf8 ("udp: no longer use SLAB_DESTROY_BY_RCU")
we do not need this special allocation mode anymore, even if it is
harmless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laura tracked poll() [and friends] regression caused by commit
e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
udp_poll() needs to know if there is a valid packet in receive queue,
even if its payload length is 0.
Change first_packet_length() to return an signed int, and use -1
as the indication of an empty queue.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include ipv4_rcv_saddr_equal() definition to avoid this sparse error :
net/ipv4/udp.c:362:5: warning: symbol 'ipv4_rcv_saddr_equal' was not
declared. Should it be static?
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a612769774 ("udp: prevent bugcheck if filter truncates packet
too much"), there followed various other fixes for similar cases such
as f4979fcea7 ("rose: limit sk_filter trim to payload").
Latter introduced a new helper sk_filter_trim_cap(), where we can pass
the trim limit directly to the socket filter handling. Make use of it
here as well with sizeof(struct udphdr) as lower cap limit and drop the
extra skb->len test in UDP's input path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If socket filter truncates an udp packet below the length of UDP header
in udpv6_queue_rcv_skb() or udp_queue_rcv_skb(), it will trigger a
BUG_ON in skb_pull_rcsum(). This BUG_ON (and therefore a system crash if
kernel is configured that way) can be easily enforced by an unprivileged
user which was reported as CVE-2016-6162. For a reproducer, see
http://seclists.org/oss-sec/2016/q3/8
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a corner case in which udp packets belonging to a same
flow are hashed to different socket when hslot->count changes from 10
to 11:
1) When hslot->count <= 10, __udp_lib_lookup() searches udp_table->hash,
and always passes 'daddr' to udp_ehashfn().
2) When hslot->count > 10, __udp_lib_lookup() searches udp_table->hash2,
but may pass 'INADDR_ANY' to udp_ehashfn() if the sockets are bound to
INADDR_ANY instead of some specific addr.
That means when hslot->count changes from 10 to 11, the hash calculated by
udp_ehashfn() is also changed, and the udp packets belonging to a same
flow will be hashed to different socket.
This is easily reproduced:
1) Create 10 udp sockets and bind all of them to 0.0.0.0:40000.
2) From the same host send udp packets to 127.0.0.1:40000, record the
socket index which receives the packets.
3) Create 1 more udp socket and bind it to 0.0.0.0:44096. The number 44096
is 40000 + UDP_HASH_SIZE(4096), this makes the new socket put into the
same hslot as the aformentioned 10 sockets, and makes the hslot->count
change from 10 to 11.
4) From the same host send udp packets to 127.0.0.1:40000, and the socket
index which receives the packets will be different from the one received
in step 2.
This should not happen as the socket bound to 0.0.0.0:44096 should not
change the behavior of the sockets bound to 0.0.0.0:40000.
It's the same case for IPv6, and this patch also fixes that.
Signed-off-by: Su, Xuemin <suxm@chinanetcenter.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Tom Herbert <tom@herbertland.com>
Fixes: 4068579e1e ("net: Implmement RFC 6936 (zero RX csums for UDP/IPv6")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore tracked a regression caused by a recent commit, which
mistakenly assumed that sk_filter() could be avoided if socket
had no current BPF filter.
The intent was to avoid udp_lib_checksum_complete() overhead.
But sk_filter() also checks skb_pfmemalloc() and
security_sock_rcv_skb(), so better call it.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paul Moore <paul@paul-moore.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Tested-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: samanthakumar <samanthakumar@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing an OpenStack configuration using VXLANs I saw the following
call trace:
RIP: 0010:[<ffffffff815fad49>] udp4_lib_lookup_skb+0x49/0x80
RSP: 0018:ffff88103867bc50 EFLAGS: 00010286
RAX: ffff88103269bf00 RBX: ffff88103269bf00 RCX: 00000000ffffffff
RDX: 0000000000004300 RSI: 0000000000000000 RDI: ffff880f2932e780
RBP: ffff88103867bc60 R08: 0000000000000000 R09: 000000009001a8c0
R10: 0000000000004400 R11: ffffffff81333a58 R12: ffff880f2932e794
R13: 0000000000000014 R14: 0000000000000014 R15: ffffe8efbfd89ca0
FS: 0000000000000000(0000) GS:ffff88103fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000488 CR3: 0000000001c06000 CR4: 00000000001426e0
Stack:
ffffffff81576515 ffffffff815733c0 ffff88103867bc98 ffffffff815fcc17
ffff88103269bf00 ffffe8efbfd89ca0 0000000000000014 0000000000000080
ffffe8efbfd89ca0 ffff88103867bcc8 ffffffff815fcf8b ffff880f2932e794
Call Trace:
[<ffffffff81576515>] ? skb_checksum+0x35/0x50
[<ffffffff815733c0>] ? skb_push+0x40/0x40
[<ffffffff815fcc17>] udp_gro_receive+0x57/0x130
[<ffffffff815fcf8b>] udp4_gro_receive+0x10b/0x2c0
[<ffffffff81605863>] inet_gro_receive+0x1d3/0x270
[<ffffffff81589e59>] dev_gro_receive+0x269/0x3b0
[<ffffffff8158a1b8>] napi_gro_receive+0x38/0x120
[<ffffffffa0871297>] gro_cell_poll+0x57/0x80 [vxlan]
[<ffffffff815899d0>] net_rx_action+0x160/0x380
[<ffffffff816965c7>] __do_softirq+0xd7/0x2c5
[<ffffffff8107d969>] run_ksoftirqd+0x29/0x50
[<ffffffff8109a50f>] smpboot_thread_fn+0x10f/0x160
[<ffffffff8109a400>] ? sort_range+0x30/0x30
[<ffffffff81096da8>] kthread+0xd8/0xf0
[<ffffffff81693c82>] ret_from_fork+0x22/0x40
[<ffffffff81096cd0>] ? kthread_park+0x60/0x60
The following trace is seen when receiving a DHCP request over a flow-based
VXLAN tunnel. I believe this is caused by the metadata dst having a NULL
dev value and as a result dev_net(dev) is causing a NULL pointer dereference.
To resolve this I am replacing the check for skb_dst(skb)->dev with just
skb->dev. This makes sense as the callers of this function are usually in
the receive path and as such skb->dev should always be populated. In
addition other functions in the area where these are called are already
using dev_net(skb->dev) to determine the namespace the UDP packet belongs
in.
Fixes: 63058308cd ("udp: Add udp6_lib_lookup_skb and udp4_lib_lookup_skb")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP uses the generic socket backlog code, and this will soon
be changed to not disable BH when protocol is called back.
We need to use appropriate SNMP accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename UDP_INC_STATS_BH() to __UDP_INC_STATS(),
and UDP6_INC_STATS_BH() to __UDP6_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ICMP_INC_STATS_BH() to __ICMP_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old days (before linux-3.0), SNMP counters were duplicated,
one for user context, and one for BH context.
After commit 8f0ea0fe3a ("snmp: reduce percpu needs by 50%")
we have a single copy, and what really matters is preemption being
enabled or disabled, since we use this_cpu_inc() or __this_cpu_inc()
respectively.
We therefore kill SNMP_INC_STATS_USER(), SNMP_ADD_STATS_USER(),
NET_INC_STATS_USER(), NET_ADD_STATS_USER(), SCTP_INC_STATS_USER(),
SNMP_INC_STATS64_USER(), SNMP_ADD_STATS64_USER(), TCP_ADD_STATS_USER(),
UDP_INC_STATS_USER(), UDP6_INC_STATS_USER(), and XFRM_INC_STATS_USER()
Following patches will rename __BH helpers to make clear their
usage is not tied to BH being disabled.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
We deleted a line of code and accidentally made the "return put_user()"
part of the if statement when it's supposed to be unconditional.
Fixes: 9f9a45beaa ('udp: do not expect udp headers on ioctl SIOCINQ')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the SO_REUSEPORT socket option, it is possible to create sockets
in the AF_INET and AF_INET6 domains which are bound to the same IPv4 address.
This is only possible with SO_REUSEPORT and when not using IPV6_V6ONLY on
the AF_INET6 sockets.
Prior to the commits referenced below, an incoming IPv4 packet would
always be routed to a socket of type AF_INET when this mixed-mode was used.
After those changes, the same packet would be routed to the most recently
bound socket (if this happened to be an AF_INET6 socket, it would
have an IPv4 mapped IPv6 address).
The change in behavior occurred because the recent SO_REUSEPORT optimizations
short-circuit the socket scoring logic as soon as they find a match. They
did not take into account the scoring logic that favors AF_INET sockets
over AF_INET6 sockets in the event of a tie.
To fix this problem, this patch changes the insertion order of AF_INET
and AF_INET6 addresses in the TCP and UDP socket lists when the sockets
have SO_REUSEPORT set. AF_INET sockets will be inserted at the head of the
list and AF_INET6 sockets with SO_REUSEPORT set will always be inserted at
the tail of the list. This will force AF_INET sockets to always be
considered first.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Fixes: 125e80b88687 ("soreuseport: fast reuseport TCP socket selection")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On udp sockets, recv cmsg IP_CMSG_CHECKSUM returns a checksum over
the packet payload. Since commit e6afc8ace6 pulled the headers,
taking skb->data as the start of transport header is incorrect. Use
the transport header pointer.
Also, when peeking at an offset from the start of the packet, only
return a checksum from the start of the peeked data. Note that the
cmsg does not subtract a tail checkum when reading truncated data.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On udp sockets, ioctl SIOCINQ returns the payload size of the first
packet. Since commit e6afc8ace6 pulled the headers, the result is
incorrect when subtracting header length. Remove that operation.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add externally visible functions to lookup a UDP socket by skb. This
will be used for GRO in UDP sockets. These functions also check
if skb->dst is set, and if it is not skb->dev is used to get dev_net.
This allows calling lookup functions before dst has been set on the
skbuff.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable peeking at UDP datagrams at the offset specified with socket
option SOL_SOCKET/SO_PEEK_OFF. Peek at any datagram in the queue, up
to the end of the given datagram.
Implement the SO_PEEK_OFF semantics introduced in commit ef64a54f6e
("sock: Introduce the SO_PEEK_OFF sock option"). Increase the offset
on peek, decrease it on regular reads.
When peeking, always checksum the packet immediately, to avoid
recomputation on subsequent peeks and final read.
The socket lock is not held for the duration of udp_recvmsg, so
peek and read operations can run concurrently. Only the last store
to sk_peek_off is preserved.
Signed-off-by: Sam Kumar <samanthakumar@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove UDP transport headers before queueing packets for reception.
This change simplifies a follow-up patch to add MSG_PEEK support.
Signed-off-by: Sam Kumar <samanthakumar@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Tranchetti