Commit Graph

49 Commits

Author SHA1 Message Date
Vitaly Bordug 796bcae736 USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]
A published errata for ppc440epx states, that when running Linux with
both EHCI and OHCI modules loaded, the EHCI module experiences a fatal
error when a high-speed device is connected to the USB2.0, and
functions normally if OHCI module is not loaded.

There used to be recommendation to use only hi-speed or full-speed
devices with specific conditions, when respective module was unloaded.
Later, it was observed that ohci suspend is enough to keep things
going, and it was turned into workaround, as explained below.

Quote from original descriprion:

The 440EPx USB 2.0 Host controller is an EHCI compliant controller.  In
USB 2.0 Host controllers, each EHCI controller has one or more companion
controllers, which may be OHCI or UHCI.  An USB 2.0 Host controller will
contain one or more ports.  For each port, only one of the controllers
is connected at any one time. In the 440EPx, there is only one OHCI
companion controller, and only one USB 2.0 Host port.
All ports on an USB 2.0 controller default to the companion
controller.  If you load only an ohci driver, it will have control of
the ports and any deviceplugged in will operate, although high speed
devices will be forced to operate at full speed.  When an ehci driver
is loaded, it explicitly takes control of the ports.  If there is a
device connected, and / or every time there is a new device connected,
the ehci driver determines if the device is high speed or not.  If it
is high speed, the driver retains control of the port.  If it is not,
the driver explicitly gives the companion controller control of the
port.

The is a software workaround that uses
Initial version of the software workaround was posted to
linux-usb-devel:

http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html

and later available from amcc.com:
http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2

The patch below is generally based on the latter, but reworked to
powerpc/of_device USB drivers, and uses a few devicetree inquiries to
get rid of (some) hardcoded defines.

Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 09:59:52 -08:00
Vikram Pandita 3a4e72cbf2 USB: Avoid 20ms delay in EHCI resume
For function ehci_bus_resume()
- Added flag resume_needed
  No need to wait for 20ms if no port was suspended

- Change mdelay to msleep

- release and reacquire the spinlock around mdelay

Signed-off-by: vikram pandita <vikram.pandita@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 09:59:50 -08:00
Alan Stern eafe5b99f2 USB: EHCI: fix remote-wakeup support for ARC/TDI core
This patch (as1147) fixes the remote-wakeup support for EHCI
controllers using the ARC/TDI "embedded-TT" core.  These controllers
turn off the RESUME bit by themselves when a port resume is complete;
hence we need to keep separate track of which ports are suspended or
in the process of resuming.

The patch also makes a couple of small improvements in ehci_irq(),
replacing reads of the command register with the value already stored
in a local variable.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Thomas Reitmayr <treitmayr@devbase.at>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-17 14:41:03 -07:00
Alan Stern d1f114d12b USB: EHCI: fix remote-wakeup regression
This patch (as1097) fixes a bug in the remote-wakeup handling in
ehci-hcd.  The driver currently does not keep track of whether the
change-suspend feature is enabled for each port; the feature is
automatically reset the first time it is read.  But recent changes to
the hub driver require that the feature be read at least twice in
order to work properly.

A bit-vector is added for storing the change-suspend feature values.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-05-29 13:59:04 -07:00
Alan Stern 3a31155cff USB: EHCI: suppress unwanted error messages
This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller.  But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.

The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller.  If it has, the
error message is suppressed.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-05-29 13:59:03 -07:00
Harvey Harrison a5abdeafed usb: use get/put_unaligned_* helpers
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-29 08:06:28 -07:00
Al Viro fd05e72009 drivers/usb annotations and fixes
* endianness annotations
* endianness fixes
* missing get_unaligned/put_unaligned

It's pretty much all over the place, changes to different files are independent.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Serial-parts-Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 10:03:31 -07:00
Alan Stern aff6d18f95 USB: fix compile problems in ehci-hcd
This patch (as1072) fixes some recently-introduced compile problems
that show up in ehci-hcd when CONFIG_PM is turned off.

	PORT_WAKE_BITS needs to be defined always.

	ehci_port_power() is called during initialization by all the
	EHCI variants other than the PCI version, in which it is
	"defined but not used".  So add a call to it.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:54 -07:00
Alan Stern 58a97ffeb2 USB: HCDs use the do_remote_wakeup flag
When a USB device is suspended, whether or not it is enabled for
remote wakeup depends on the device_may_wakeup() setting.  The setting
is then saved in the do_remote_wakeup flag.

Later on, however, the device_may_wakeup() value can change because of
user activity.  So when testing whether a suspended device is or
should be enabled for remote wakeup, we should always test
do_remote_wakeup instead of device_may_wakeup().  This patch (as1076)
makes that change for root hubs in several places.

The patch also adjusts uhci-hcd so that when an autostopped controller
is suspended, the remote wakeup setting agrees with the value recorded
in the root hub's do_remote_wakeup flag.

And the patch adjusts ehci-hcd so that wakeup events on selectively
suspended ports (i.e., the bus itself isn't suspended) don't turn on
the PME# wakeup signal.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:53 -07:00
David Brownell 9776afc8b3 USB: ehci: minor cleanups
Minor cleanups to the EHCI code:  revision history is what source
code repositories should have.  Switch to a more standard way to
kick in verbose debugging -- don't be EHCI-specific.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:34 -07:00
Alan Stern feccc30d90 USB: remove CONFIG_USB_PERSIST setting
This patch (as1047) removes the USB_PERSIST Kconfig option, enabling
it permanently.  It also prevents the power/persist attribute from
being created for hub devices; there's no point in having it since
USB-PERSIST is always turned on for hubs.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:32 -07:00
Alan Stern 3bb1af5243 USB: EHCI: carry out port handover during each root-hub resume
This patch (as1044) causes EHCI port handover for non-high-speed
devices to occur during every root-hub resume, not just in cases where
the controller lost power or was reset.  This is necessary because:

	When some machines go into suspend, they remove power from
	on-board USB devices while retaining suspend current for USB
	controllers.

	The user might well unplug a USB device while the system is
	suspended and then plug it back in before resuming.

A corresponding change is made to the core resume routine; now
high-speed root hubs will always be resumed when the system wakes up,
even if they were suspended before the system went to sleep.  If this
weren't done then EHCI port handover wouldn't work, since it is called
when the EHCI root hub is resumed.

Finally, a comment is added to the hub driver explaining the khubd has
to be freezable; if it weren't frozen then it could interfere with
port handover.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:32 -07:00
David Brownell cdc647a9b7 USB: another ehci_iaa_watchdog fix
This patch, suggested by Alan Stern, fixes the hung USB issues
on my notebook from suspend/resume cycles.

It does so by eliminating some confusion about the internal state
machine associated with unlinking from the EHCI async schedule ring,
which caused a recent regression:

  http://bugzilla.kernel.org/show_bug.cgi?id=10345

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-02 15:06:08 -07:00
David Brownell cd4cdc93ce usb: ehci, remove false clear-reset path
Some of the "EHCI ports reset forever" problems may be explained by
code paths which wrongly flagged resets as complete.  This removes
two such paths; the ehci_hub_status_data() path should be the only one
to have an effect, since it was already properly flagged on the other
path.  (Issue noted by Minhyoung Kim <a9a9@lge.com>.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:06 -08:00
Alan Stern cd930c9314 USB: EHCI: add a short delay to the bus_suspend routine
This patch (as1031) adds a short delay to the bus-suspend routine in
ehci-hcd.  Without it some devices disconnect when they should
suspend.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:03 -08:00
Alan Stern f8fa7571a9 USB: EHCI: move del_timer_sync calls outside spinlocked region
This patch (as1030b) moves a del_timer_sync() call outside the scope of a
spinlock, where it could cause a deadlock, and adds a new
del_timer_sync() call for the new IAA watchdog timer (it was omitted
by mistake).

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:03 -08:00
Alan Stern 07d29b63ef USB: EHCI: add separate IAA watchdog timer
This patch (as1028) was mostly written by David Brownell; I made only
a few changes (extra log info and a small bug fix -- which might
account for why David's version had to be reverted).  It adds a new
watchdog timer to the ehci-hcd driver to be used exclusively for
detecting lost or missing IAA notifications.

Previously a shared timer had been used, which may have led to some
problems as reported by Christian Hoffmann.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:34:55 -08:00
Balaji Rao 90da096ee4 USB: force handover port to companion when hub_port_connect_change fails
This patch hands over the port to the companion when the
hub_port_connect_change fails.

Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:34:52 -08:00
Tony Jones 5a3201b280 USB: Convert from class_device to device for USB core
Convert from class_device to device for drivers/usb/core.

Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:34:46 -08:00
Robert P. J. Day 3a4fa0a25d Fix misspellings of "system", "controller", "interrupt" and "necessary".
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
2007-10-19 23:10:43 +02:00
Alan Stern cfa59dab27 USB: Don't resume root hub if the controller is suspended
Root hubs can't be resumed if their parent controller device is still
suspended.  This patch (as925) adds a check for that condition in
hcd_bus_resume() and prevents it from being treated as a fatal
controller failure.

ehci-hcd is updated to add the corresponding test.  Unnecessary
debugging messages are removed from uhci-hcd and dummy-hcd.  The
error return code from dummy-hcd is changed to -ESHUTDOWN, the same as
the others.  ohci-hcd doesn't need any changes.

Suspend handling in the non-PCI host drivers is somewhat hit-and-miss.
This patch shouldn't have any effect on them.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:34:39 -07:00
Christian Engelmayer 756aa6b3d5 ehci-hub: improved over-current recovery
According to the USB Specification Revision 2.0 chapter 11.12.5
a hub experiencing an over-current condition must place all
affected ports in the powered-off state. It seems that some root
hubs need port power to be cycled by software in order to get back
to normal functionality after an over-current condition ... like
the EHCI implementation on an MPC8343E.

Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:34:31 -07:00
Alan Stern 3c519b846c USB: EHCI: fix handover for designated full-speed ports
This patch (as895) fixes up a loose end in the port-handover code for
the USB-Persist facility.  A special case occurs when a high-speed
device is attached to a port which the user has designated to run at
full-speed only; the port must be disabled before the handover can
take place.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:47 -07:00
Alan Stern 383975d765 USB: EHCI, OHCI: handover changes
This patch (as887) changes the way ehci-hcd and ohci-hcd handle a loss
of VBUS power during suspend.  In order for the USB-persist facility
to work correctly, it is necessary for low- and full-speed devices
attached to a high-speed port to be handed back to the companion
controller during resume processing.

This entails three changes: adding code to ehci-hcd to perform the
handover, removing code from ohci-hcd to turn off ports during
root-hub reinit, and adding code to ohci-hcd to turn on ports during
PCI controller resume.  (Other bus glue resume methods for platforms
supporting high-speed controllers would need a similar change, if any
existed.)

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:47 -07:00
Alan Stern e198a31489 EHCI: add delay to bus_resume before accessing ports
This patch (as870) adds a delay to ehci-hcd's bus_resume routine.
Apparently there are controllers and/or BIOSes out there which need
such a delay to get the ports back into their correct state.  This
fixes Bugzilla #8190.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:35 -07:00
Max Dmitrichenko 6454365260 USB: fix Unaligned access in EHCI driver
I get following warnings on spar64:
Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd]

Despite of the comment in the patched code, the type cast used there
does make unaligned access. The fix was made as it's done in
ohci-hub.c.

Signed-off-by: Max Dmitrichenko <dmitrmax@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-03-09 19:52:25 -08:00
Alan Stern 8c774fe8a0 EHCI: add debugging message to ehci_bus_suspend
This patch (as848) adds a useful little debugging message to let us
know when ehci-hcd's bus_suspend method runs.  The other HCDs have
similar messages; now ehci-hcd doesn't need to feel left out.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-16 15:32:18 -08:00
Alan Stern 629e4427aa EHCI: fix interrupt-driven remote wakeup
Now that port status change notifications are interrupt-driven,
ehci-hcd needs to tell usbcore when a remote-wakeup resume operation
is finished -- we can no longer rely on the core to poll and find
out.  This patch (as843) uses the root-hub status timer to force a
poll after the resume is complete.

The patch also changes the test for detecting when the TDRSMDN resume
period has expired.  It's necessary to use time_after_eq() instead of
time_after(), since the polling is triggered precisely by a timer.
The same change is made for TDRSTR reset expiration, for consistency.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:39 -08:00
Alan Stern 57e06c1137 EHCI: force high-speed devices to run at full speed
This patch (as710) adds a sysfs class-device attribute file named
"companion" for EHCI controllers.  The file contains a list of port
numbers that are dedicated to the companion controller; by writing a
port number to the file the user can force a high-speed device
attached directly to the computer to run at full speed.  (As far as I
know it is not possible to do this for a device attached to an
external hub.)  A port is removed from the file by writing the
negative of its port number.

Several users have asked for this facility and it seems like a useful
thing to have.  Every now and then one runs across a device which
behaves much better at full speed than at high speed.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:37 -08:00
Alan Stern 625b5c9a00 EHCI: don't hide ports owned by the companion
This patch (as709) changes the way ehci-hcd presents port status
values for ports owned by the companion controller.  It no longer
hides the information; in particular, it allows the core to see the
disconnect event that occurs when a full- or low-speed device is
switched over to the companion.  This is required for the next patch
in this series.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:37 -08:00
Alan Stern e6316565e5 EHCI: local variable for port status register
This patch (as708) introduces a local variable to hold the port
status-register address in ehci-hub.c.  There's not much improvement
in the object code, but it sure is a lot easier to read.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:37 -08:00
Benjamin Herrenschmidt 083522d766 USB: Implement support for EHCI with big endian MMIO
This patch implements supports for EHCI controllers whose MMIO
registers are big endian and enables that functionality for
the Toshiba SCC chip. It does _not_ add support for big endian
in-memory data structures as this is not needed for that chip
and I hope it will never be.

The guts of the patch are to convert readl(...) to
ehci_readl(ehci, ...) and similarly for register writes.

Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:32 -08:00
Alan Stern 8c03356a55 EHCI: Fix root-hub and port suspend/resume problems
This patch (as738b) fixes numerous problems in the controller/root-hub
suspend/resume/remote-wakeup support in ehci-hcd:

	The bus_resume() routine should wake up only the ports that
	were suspended by bus_suspend().  Ports that were already
	suspended should remain that way.

	The interrupt mask is used to detect loss of power in the
	bus_resume() routine (if the mask is 0 then power was lost).
	However bus_suspend() always sets the mask to 0.  Instead the
	mask should retain its normal value, with port-change-detect
	interrupts disabled if remote wakeup is turned off.

	The interrupt mask should be reset to its correct value at the
	end of bus_resume() regardless of whether power was lost.

	bus_resume() reinitializes the operational registers if power
	was lost.  However those registers are not in the aux power
	well, hence they can lose their values whenever the controller
	is put into D3.  They should always be reinitialized.

	When a port-change interrupt occurs and the root hub is
	suspended, the interrupt handler should request a root-hub
	resume instead of starting up the controller all by itself.

	There's no need for the interrupt handler to request a
	root-hub resume every time a suspended port sends a
	remote-wakeup request.

	The pci_resume() method doesn't need to check for connected
	ports when deciding whether or not to reset the controller.
	It can make that decision based on whether Vaux power was
	maintained.

	Even when the controller does not need to be reset,
	pci_resume() must undo the effect of pci_suspend() by
	re-enabling the interrupt mask.

	If power was lost, pci_resume() must not call ehci_run().
	At this point the root hub is still supposed to be suspended,
	not running.  It's enough to rewrite the command register and
	set the configured_flag.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
David Brownell 93f1a47c4a USB: add ehci_hcd.ignore_oc parameter
Certain boards seem to like to issue false overcurrent notifications, for
example on ports that don't have anything connected to them.  This looks
like a hardware error, at the level of noise to those ports' overcurrent
input signals (or non-debounced VBUS comparators).  This surfaces to users
as truly massive amounts of syslog spam from khubd (which is appropriate
for real hardware problems, except for the volume from multiple ports).

Using this new "ignore_oc" flag helps such systems work more sanely, by
preventing such indications from getting to khubd (and spam syslog).  The
downside is of course that true overcurrent errors will be masked; they'll
appear as spontaneous disconnects, without the diagnostics that will let
users troubleshoot issues like short circuited cables.

Note that the bulk of these reports seem to be with VIA southbridges, but
I think some were with Intel ones.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
David Brownell f0d7f27351 USB: EHCI hooks for high speed electrical tests
EHCI hooks for high speed electrical tests of the root hub ports.

The expectation is that a usermode program actually triggers the test,
making the same control request it would make for an external hub.
Tests for peripheral upstream ports would issue a different request.
In all cases, the hardware needs re-initialization before it could
be used "normally" again (e.g. unplug/replug, rmmod/modprobe).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:36 -08:00
Greg Kroah-Hartman 64f89798da USB: revert EHCI VIA workaround patch
This reverts 26f953fd88 which caused
resume problems on the mac mini.

Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-10-17 13:57:18 -07:00
David Howells 7d12e780e0 IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around.  On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable.  On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions.  Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller.  A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386.  I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs.  Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

	struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

	set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

	-	update_process_times(user_mode(regs));
	-	profile_tick(CPU_PROFILING, regs);
	+	update_process_times(user_mode(get_irq_regs()));
	+	profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

 (*) input_dev() is now gone entirely.  The regs pointer is no longer stored in
     the input_dev struct.

 (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking.  It does
     something different depending on whether it's been supplied with a regs
     pointer or not.

 (*) Various IRQ handler function pointers have been moved to type
     irq_handler_t.

Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 15:10:12 +01:00
David Brownell 26f953fd88 USB: EHCI update VIA workaround
This revamps handling of the hardware "async advance" IRQ, and its watchdog
timer.  Basically it dis-entangles that important timeout from the others,
simplifying the associated state and code to make it more robust.

This reportedly improves behavior of EHCI on some systems with VIA chips,
and AFAIK won't affect non-VIA hardware.  VIA systems need this code to
recover from silcon bugs whereby the "async advance" IRQ isn't issued.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27 11:59:00 -07:00
David Brownell 53bd6a601a USB: EHCI whitespace fixes (cosmetic)
[ ... when you have an editor set to remind you of whitespace bugs ... ]

Cosmetic EHCI changes: remove end-of-line whitespace, spaces before tabs.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27 11:58:56 -07:00
David Brownell f8aeb3bb86 [PATCH] USB: EHCI and NF2 quirk
This teaches the EHCI driver about a quirk seen in older NForce2 chips,
adding a workaround to ignore selective suspend requests.  Bus-wide
(so-called "global") suspend still works, as does USB wakeup of a
root hub that's globally suspended.

There's still a hole in this support though.  Strictly speaking, this
should _fail_ selective suspend requests, rather than ignoring them,
since doing it this way means that devices which should be able to issue
remote wakeup are not going to be able to do that.  For now, we'll just
live with that problem ... since usbcore expects to do selective suspend
on the way towards a full bus suspend, and usbcore needs to be able to
do full bus suspend.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-20 14:49:55 -08:00
David Brownell 2c1c3c4cd5 [PATCH] USB: EHCI updates (4/4) driver model wakeup flags
This teaches the EHCI driver to use the new driver model wakeup flags,
replacing the similar ones in the HCD glue.  It also adds a workaround
for the current glitch whereby PCI init doesn't init the wakeup flags
from the PCI PM capabilities.  (EHCI controllers don't worry about
legacy mode; the PCI PM capability would always do the job.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-04 13:48:30 -08:00
David Brownell f03c17fc9a [PATCH] USB: EHCI updates
This fixes some bugs in EHCI suspend/resume that joined us over the past
few releases (as usbcore, PCI, pmcore, and other components evolved):

  - Removes suspend and resume recursion from the EHCI driver, getting
    rid of the USB_SUSPEND special casing.

  - Updates the wakeup mechanism to work again; there's a newish usbcore
    call it needs to use.

  - Provide simpler tests for "do we need to restart from scratch", to
    address another case where PCI Vaux was lost.  (In this case it was
    restoring a swsusp snapshot, but there could be others.)

Un-exports a symbol that was temporarily exported.

A notable change from previous version is that this doesn't move
the spinlock init, so there's still a resume/reinit path bug.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-23 23:04:28 -08:00
Alan Stern 0c0382e32d [PATCH] USB: Rename hcd->hub_suspend to hcd->bus_suspend
This patch (as580) is perhaps the only result from the long discussion I
had with David about his changes to the root-hub suspend/resume code.  It
renames the hub_suspend and hub_resume methods in struct usb_hcd to
bus_suspend and bus_resume.  These are more descriptive names, since the
methods really do suspend or resume an entire USB bus, and less likely to
be confused with the hub_suspend and hub_resume routines in hub.c.

It also takes David's advice about removing the layer of bus glue, where
those methods are called.  And it implements a related change that David
made to the other HCDs but forgot to put into dummy_hcd.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28 16:47:44 -07:00
David Brownell 10f6524a8e [PATCH] USB: EHCI port tweaks
One change may improve some S1 or S3 resume cases, and the other
seems mostly to explain some strange state "lsusb" would show.
Two fixes:

  - On resume, don't think about resuming any unpowered port, or
    resetting any port with OWNER set to the OHCI/UHCI companion.
    This will make some S1 and S3 resume scenarios work better.

  - PORT_CSC was not being cleared correctly in ehci_hub_status_data.
    This was visible at least through current versions of "lsusb",
    and might have caused some other hub related strangeness.

    The fix addresses all three write-to-clear bits, using the same
    approach that UHCI happens to use:  a mask of bits that are
    cleared in most writes to that port status register.

Original patch seems to have been from from William.Morrow@amd.com
and this version (from David) finishes the write-to-clear changes.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-12 12:23:42 -07:00
David Brownell d49d431744 [PATCH] USB: misc ehci updates
Various minor EHCI updates

   * Dump some more info in the debug dumps, notably the product
     description (e.g. chip vendor), BIOS handhake flags, and
     debug port status (when it's not managed by the HCD).

   * Minor updates to the BIOS handoff code:  always flag the HCD
     as owned by Linux (in case BIOS doesn't grab it "early"),
     and on the buggy-BIOS path always match the "early handoff"
     code and forcibly disable SMI IRQs.

   * For the disabled 64bit DMA support, there's now a constant
     to use for the mask; use it.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-06-27 14:43:55 -07:00
David Brownell c22fa3acbc [PATCH] spin longer for ehci port reset completion
This makes the EHCI driver spin a bit longer before concluding that the
port reset failed.  "Obviously safe."

It allows some devices to enumerate that previously didn't.  We've seen
a bunch of these problem reports recently, this will make some go away.

As reported by Michael Zapf <Michael.Zapf@uni-kassel.de>, some EHCI
controllers seem to take forever to finish port resets and produce
"port N reset error -110" type errors.  Spinning a bit longer helps.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-13 08:20:41 -07:00
David Brownell 4756ae5b52 [PATCH] USB: ehci suspend must stop timer
Force the EHCI watchdog timer off during suspend, in case for some
reason it was still running after the root hub suspended.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-05-16 21:44:25 -07:00
David Brownell 56c1e26d75 [PATCH] USB: ehci power fixes
Miscellaneous updates for EHCI.

 - Mostly updates the power switching on EHCI controllers.  One routine
   centralizes the "power on/off all ports" logic, and the capability to
   do that is reported more correctly.

 - Courtesy Colin Leroy, a patch to always power up ports after resumes
   which didn't keep a USB device suspended.  The reset-everything logic
   powers down those ports (on some hardware) so something needs to turn
   them back on.

 - Minor tweaks/bugfixes for the debug port support.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-05-03 23:31:49 -07:00
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00