When performing segmentation, the mac_len value is copied right
out of the original skb. However, this value is not always set correctly
(like when the packet is VLAN-tagged) and we'll end up copying a bad
value.
One way to demonstrate this is to configure a VM which tags
packets internally and turn off VLAN acceleration on the forwarding
bridge port. The packets show up corrupt like this:
16:18:24.985548 52:54:00🆎be:25 > 52:54:00:26:ce:a3, ethertype 802.1Q
(0x8100), length 1518: vlan 100, p 0, ethertype 0x05e0,
0x0000: 8cdb 1c7c 8cdb 0064 4006 b59d 0a00 6402 ...|...d@.....d.
0x0010: 0a00 6401 9e0d b441 0a5e 64ec 0330 14fa ..d....A.^d..0..
0x0020: 29e3 01c9 f871 0000 0101 080a 000a e833)....q.........3
0x0030: 000f 8c75 6e65 7470 6572 6600 6e65 7470 ...unetperf.netp
0x0040: 6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
0x0050: 6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
0x0060: 6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
...
This also leads to awful throughput as GSO packets are dropped and
cause retransmissions.
The solution is to set the mac_len using the values already available
in then new skb. We've already adjusted all of the header offset, so we
might as well correctly figure out the mac_len using skb_reset_mac_len().
After this change, packets are segmented correctly and performance
is restored.
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PAGE_ALIGNED(...) instead of IS_ALIGNED(..., PAGE_SIZE).
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with ICMPv[46] Error Message, function icmp_socket_deliver()
and icmpv6_notify() do some valid checks on packet's length, but then some
protocols check packet's length redaudantly. So remove those duplicated
statements, and increase counter ICMP_MIB_INERRORS/ICMP6_MIB_INERRORS in
function icmp_socket_deliver() and icmpv6_notify() respectively.
In addition, add missed counter in udp6/udplite6 when socket is NULL.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP socket extensions API document describes the v4mapping option as
follows:
8.1.15. Set/Clear IPv4 Mapped Addresses (SCTP_I_WANT_MAPPED_V4_ADDR)
This socket option is a Boolean flag which turns on or off the
mapping of IPv4 addresses. If this option is turned on, then IPv4
addresses will be mapped to V6 representation. If this option is
turned off, then no mapping will be done of V4 addresses and a user
will receive both PF_INET6 and PF_INET type addresses on the socket.
See [RFC3542] for more details on mapped V6 addresses.
This description isn't really in line with what the code does though.
Introduce addr_to_user (renamed addr_v4map), which should be called
before any sockaddr is passed back to user space. The new function
places the sockaddr into the correct format depending on the
SCTP_I_WANT_MAPPED_V4_ADDR option.
Audit all places that touched v4mapped and either sanely construct
a v4 or v6 address then call addr_to_user, or drop the
unnecessary v4mapped check entirely.
Audit all places that call addr_to_user and verify they are on a sycall
return path.
Add a custom getname that formats the address properly.
Several bugs are addressed:
- SCTP_I_WANT_MAPPED_V4_ADDR=0 often returned garbage for
addresses to user space
- The addr_len returned from recvmsg was not correct when
returning AF_INET on a v6 socket
- flowlabel and scope_id were not zerod when promoting
a v4 to v6
- Some syscalls like bind and connect behaved differently
depending on v4mapped
Tested bind, getpeername, getsockname, connect, and recvmsg for proper
behaviour in v4mapped = 1 and 0 cases.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains netfilter updates for net-next, they are:
1) Add the reject expression for the nf_tables bridge family, this
allows us to send explicit reject (TCP RST / ICMP dest unrech) to
the packets matching a rule.
2) Simplify and consolidate the nf_tables set dumping logic. This uses
netlink control->data to filter out depending on the request.
3) Perform garbage collection in xt_hashlimit using a workqueue instead
of a timer, which is problematic when many entries are in place in
the tables, from Eric Dumazet.
4) Remove leftover code from the removed ulog target support, from
Paul Bolle.
5) Dump unmodified flags in the netfilter packet accounting when resetting
counters, so userspace knows that a counter was in overquota situation,
from Alexey Perevalov.
6) Fix wrong usage of the bitwise functions in nfnetlink_acct, also from
Alexey.
7) Fix a crash when adding new set element with an empty NFTA_SET_ELEM_LIST
attribute.
This patchset also includes a couple of cleanups for xt_LED from
Duan Jiong and for nf_conntrack_ipv4 (using coccinelle) from
Himangi Saraogi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
commit d23ff7016 (tcp: add generic netlink support for tcp_metrics) introduced
netlink support for the new tcp_metrics, however it restricted getting of
tcp_metrics to root user only. This is a change from how these values could
have been fetched when in the old route cache. Unless there's a legitimate
reason to restrict the reading of these values it would be better if normal
users could fetch them.
Cc: Julian Anastasov <ja@ssi.bg>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 38ca83a5 added RDMA_CM_EVENT_TIMEWAIT_EXIT. But that status
is relevant only for consumers that re-use their QPs on new
connections. xprtrdma creates a fresh QP on reconnection, so that
event should be explicitly ignored.
Squelch the alarming "unexpected CM event" message.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up.
RPCRDMA_PERSISTENT_REGISTRATION was a compile-time switch between
RPCRDMA_REGISTER mode and RPCRDMA_ALLPHYSICAL mode. Since
RPCRDMA_REGISTER has been removed, there's no need for the extra
conditional compilation.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: The return code is used only for dprintk's that are
already redundant.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Minor optimization: grab rpcrdma_tk_lock_g and disable hard IRQs
just once after clearing the receive completion queue.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Currently rpcrdma_buffer_create() allocates struct rpcrdma_mw's as
a single contiguous area of memory. It amounts to quite a bit of
memory, and there's no requirement for these to be carved from a
single piece of contiguous memory.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Name frmr_wr after the opcode of the Work Request,
consistent with the send and local invalidation paths.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Instead of relying on a completion to change the state of an FRMR
to FRMR_IS_INVALID, set it in advance. If an error occurs, a completion
will fire anyway and mark the FRMR FRMR_IS_STALE.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Instead of relying on a completion to change the state of an FRMR
to FRMR_IS_VALID, set it in advance. If an error occurs, a completion
will fire anyway and mark the FRMR FRMR_IS_STALE.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Any FRMR arriving in rpcrdma_register_frmr_external() is now
guaranteed to be either invalid, or to be targeted by a queued
LOCAL_INV that will invalidate it before the adapter processes
the FAST_REG_MR being built here.
The problem with current arrangement of chaining a LOCAL_INV to the
FAST_REG_MR is that if the transport is not connected, the LOCAL_INV
is flushed and the FAST_REG_MR is flushed. This leaves the FRMR
valid with the old rkey. But rpcrdma_register_frmr_external() has
already bumped the in-memory rkey.
Next time through rpcrdma_register_frmr_external(), a LOCAL_INV and
FAST_REG_MR is attempted again because the FRMR is still valid. But
the rkey no longer matches the hardware's rkey, and a memory
management operation error occurs.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When a LOCAL_INV Work Request is flushed, it leaves an FRMR in the
VALID state. This FRMR can be returned by rpcrdma_buffer_get(), and
must be knocked down in rpcrdma_register_frmr_external() before it
can be re-used.
Instead, capture these in rpcrdma_buffer_get(), and reset them.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
FAST_REG_MR Work Requests update a Memory Region's rkey. Rkey's are
used to block unwanted access to the memory controlled by an MR. The
rkey is passed to the receiver (the NFS server, in our case), and is
also used by xprtrdma to invalidate the MR when the RPC is complete.
When a FAST_REG_MR Work Request is flushed after a transport
disconnect, xprtrdma cannot tell whether the WR actually hit the
adapter or not. So it is indeterminant at that point whether the
existing rkey is still valid.
After the transport connection is re-established, the next
FAST_REG_MR or LOCAL_INV Work Request against that MR can sometimes
fail because the rkey value does not match what xprtrdma expects.
The only reliable way to recover in this case is to deregister and
register the MR before it is used again. These operations can be
done only in a process context, so handle it in the transport
connect worker.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If the rb_mws list is exhausted, clean up and return NULL so that
call_allocate() will delay and try again.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
During connection loss recovery, need to visit every MW in a
buffer pool. Any MW that is in use by an RPC will not be on the
rb_mws list.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If posting a FAST_REG_MR Work Reqeust fails, revert the rkey update
to avoid subsequent IB_WC_MW_BIND_ERR completions.
Suggested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean ups:
- make it obvious that the rl_mw field is a pointer -- allocated
separately, not as part of struct rpcrdma_mr_seg
- promote "struct {} frmr;" to a named type
- promote the state enum to a named type
- name the MW state field the same way other fields in
rpcrdma_mw are named
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If FRMR registration fails, it's likely to transition the QP to the
error state. Or, registration may have failed because the QP is
_already_ in ERROR.
Thus calling rpcrdma_deregister_external() in
rpcrdma_create_chunks() is useless in FRMR mode: the LOCAL_INVs just
get flushed.
It is safe to leave existing registrations: when FRMR registration
is tried again, rpcrdma_register_frmr_external() checks if each FRMR
is already/still VALID, and knocks it down first if it is.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
xprtrdma is currently throwing away queued completions during
a reconnect. RPC replies posted just before connection loss, or
successful completions that change the state of an FRMR, can be
missed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Various reports of:
rpcrdma_qp_async_error_upcall: QP error 3 on device mlx4_0
ep ffff8800bfd3e848
Ensure that rkeys in already-marshalled RPC/RDMA headers are
refreshed after the QP has been replaced by a reconnect.
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=249
Suggested-by: Selvin Xavier <Selvin.Xavier@Emulex.Com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When the client uses physical memory registration, each page in the
payload gets its own array entry in the RPC/RDMA header's chunk list.
Therefore, don't advertise a maximum payload size that would require
more array entries than can fit in the RPC buffer where RPC/RDMA
headers are built.
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=248
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Ensure ia->ri_id remains valid while invoking dma_unmap_page() or
posting LOCAL_INV during a transport reconnect. Otherwise,
ia->ri_id->device or ia->ri_id->qp is NULL, which triggers a panic.
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=259
Fixes: ec62f40 'xprtrdma: Ensure ia->ri_id->qp is not NULL when reconnecting'
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
seg1->mr_nsegs is not yet initialized when it is used to unmap
segments during an error exit. Use the same unmapping logic for
all error exits.
"if (frmr_wr.wr.fast_reg.length < len) {" used to be a BUG_ON check.
The broken code will never be executed under normal operation.
Fixes: c977dea (xprtrdma: Remove BUG_ON() call sites)
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Shirley Ma <shirley.ma@oracle.com>
Tested-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
An FDB entry with vlan_id 0 doesn't mean it is used in vlan 0, but used when
vlan_filtering is disabled.
There is inconsistency around NDA_VLAN whose payload is 0 - even if we add
an entry by RTM_NEWNEIGH without any NDA_VLAN, and even though adding an
entry with NDA_VLAN 0 is prohibited, we get an entry with NDA_VLAN 0 by
RTM_GETNEIGH.
Dumping an FDB entry with vlan_id 0 shouldn't include NDA_VLAN.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, the kernel oopses in nla_for_each_nested when iterating over
the unset attribute NFTA_SET_ELEM_LIST_ELEMENTS in the
nf_tables_{new,del}setelem() path.
netlink: 65524 bytes leftover after parsing attributes in process `nft'.
[...]
Oops: 0000 [#1] SMP
[...]
CPU: 2 PID: 6287 Comm: nft Not tainted 3.16.0-rc2+ #169
RIP: 0010:[<ffffffffa0526e61>] [<ffffffffa0526e61>] nf_tables_newsetelem+0x82/0xec [nf_tables]
[...]
Call Trace:
[<ffffffffa05178c4>] nfnetlink_rcv+0x2e7/0x3d7 [nfnetlink]
[<ffffffffa0517939>] ? nfnetlink_rcv+0x35c/0x3d7 [nfnetlink]
[<ffffffff8137d300>] netlink_unicast+0xf8/0x17a
[<ffffffff8137d6a5>] netlink_sendmsg+0x323/0x351
[...]
Fix this by returning -EINVAL if this attribute is not set, which
doesn't make sense at all since those commands are there to add and to
delete elements from the set.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Bit helper functions were used for manipulation with NFACCT_F_OVERQUOTA,
but they are accepting pit position, but not a bit mask. As a result
not a third bit for NFACCT_F_OVERQUOTA was set, but forth. Such
behaviour was dangarous and could lead to unexpected overquota report
result.
Signed-off-by: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2014-07-30
This is the last pull request for ipsec-next before I'll be
off for two weeks starting on friday. David, can you please
take urgent ipsec patches directly into net/net-next during
this time?
1) Error handling simplifications for vti and vti6.
From Mathias Krause.
2) Remove a duplicate semicolon after a return statement.
From Christoph Paasch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_unattached_filter_destroy() does not always need to release the
filter object via rcu. Since this filter is never attached to the
socket, the caller should be responsible for releasing the filter
in a safe way, which may not necessarily imply rcu.
This is a short summary of clients of this function:
1) xt_bpf.c and cls_bpf.c use the bpf matchers from rules, these rules
are removed from the packet path before the filter is released. Thus,
the framework makes sure the filter is safely removed.
2) In the ppp driver, the ppp_lock ensures serialization between the
xmit and filter attachment/detachment path. This doesn't use rcu
so deferred release via rcu makes no sense.
3) In the isdn/ppp driver, it is called from isdn_ppp_release()
the isdn_ppp_ioctl(). This driver uses mutex and spinlocks, no rcu.
Thus, deferred rcu makes no sense to me either, the deferred releases
may be just masking the effects of wrong locking strategy, which
should be fixed in the driver itself.
4) In the team driver, this is the only place where the rcu
synchronization with unattached filter is used. Therefore, this
patch introduces synchronize_rcu() which is called from the
genetlink path to make sure the filter doesn't go away while packets
are still walking over it. I think we can revisit this once struct
bpf_prog (that only wraps specific bpf code bits) is in place, then
add some specific struct rcu_head in the scope of the team driver if
Jiri thinks this is needed.
Deferred rcu release for unattached filters was originally introduced
in 302d663 ("filter: Allow to create sk-unattached filters").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need for the unlikely(), WARN_ON() and BUG_ON() internally use
unlikely() on the condition.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vegas we do a multiplication of the cwnd and the rtt. This
may overflow and thus their result is stored in a u64. However, we first
need to cast the cwnd so that actually 64-bit arithmetic is done.
Then, we need to do do_div to allow this to be used on 32-bit arches.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Doug Leith <doug.leith@nuim.ie>
Fixes: 8d3a564da3 (tcp: tcp_vegas cong avoid fix)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In veno we do a multiplication of the cwnd and the rtt. This
may overflow and thus their result is stored in a u64. However, we first
need to cast the cwnd so that actually 64-bit arithmetic is done.
A first attempt at fixing 76f1017757 ([TCP]: TCP Veno congestion
control) was made by 159131149c (tcp: Overflow bug in Vegas), but it
failed to add the required cast in tcp_veno_cong_avoid().
Fixes: 76f1017757 ([TCP]: TCP Veno congestion control)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current explanation of dcb_app->priority is wrong. It says priority is
expected to be a 3-bit unsigned integer which is only true when working with
DCBx-IEEE. Use of dcb_app->priority by DCBx-CEE expects it to be 802.1p user
priority bitmap. Updated accordingly
This affects the cxgb4 driver, but I will post those changes as part of a
larger changeset shortly.
Fixes: 3e29027af4 ("dcbnl: add support for ieee8021Qaz attributes")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ipv4 tunnels created with "local any remote $ip" didn't work properly since
7d442fab0 (ipv4: Cache dst in tunnels). 99% of packets sent via those tunnels
had src addr = 0.0.0.0. That was because only dst_entry was cached, although
fl4.saddr has to be cached too. Every time ip_tunnel_xmit used cached dst_entry
(tunnel_rtable_get returned non-NULL), fl4.saddr was initialized with
tnl_params->saddr (= 0 in our case), and wasn't changed until iptunnel_xmit().
This patch adds saddr to ip_tunnel->dst_cache, fixing this issue.
Reported-by: Sergey Popov <pinkbyte@gentoo.org>
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we're not bondable we should never send any other SSP
authentication requirement besides one of the non-bonding ones.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This setting maps to the HCI_BONDABLE flag which tracks whether we're
bondable or not. Therefore, rename the mgmt setting and respective
command accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The HCI_PAIRABLE flag isn't actually controlling whether we're pairable
but whether we're bondable. Therefore, rename it accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new leds bit handling produces this spares warning.
CHECK net/bluetooth/hidp/core.c
net/bluetooth/hidp/core.c:156:60: warning: dubious: x | !y
Just fix it by doing an explicit x << 0 shift operation.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Both BT_CONNECTED and BT_CONFIG state mean that we have a baseband link
available. We should therefore check for either of these when pairing
and deciding whether to call hci_conn_security() directly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CHECK: braces {} should be used on all arms of this statement
+ if ((iphc0 & 0x03) != LOWPAN_IPHC_TTL_I)
[...]
+ else {
[...]
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
WARNING: Missing a blank line after declarations
+ struct sk_buff *new;
+ if (uncompress_udp_header(skb, &uh))
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch fixes all the issues with alignment matching of open
parenthesis found by checkpatch.pl and makes them follow the
network coding style now.
CHECK: Alignment should match open parenthesis
+static int uncompress_addr(struct sk_buff *skb,
+ struct in6_addr *ipaddr, const u8 address_mode,
CHECK: Alignment should match open parenthesis
+static int uncompress_context_based_src_addr(struct sk_buff *skb,
+ struct in6_addr *ipaddr,
CHECK: Alignment should match open parenthesis
+static int skb_deliver(struct sk_buff *skb, struct ipv6hdr *hdr,
+ struct net_device *dev, skb_delivery_cb deliver_skb)
CHECK: Alignment should match open parenthesis
+ new = skb_copy_expand(skb, sizeof(struct ipv6hdr), skb_tailroom(skb),
+ GFP_ATOMIC);
CHECK: Alignment should match open parenthesis
+ raw_dump_table(__func__, "raw skb data dump before receiving",
+ new->data, new->len);
CHECK: Alignment should match open parenthesis
+lowpan_uncompress_multicast_daddr(struct sk_buff *skb,
+ struct in6_addr *ipaddr,
CHECK: Alignment should match open parenthesis
+ raw_dump_inline(NULL, "Reconstructed ipv6 multicast addr is",
+ ipaddr->s6_addr, 16);
CHECK: Alignment should match open parenthesis
+int lowpan_process_data(struct sk_buff *skb, struct net_device *dev,
+ const u8 *saddr, const u8 saddr_type, const u8 saddr_len,
CHECK: Alignment should match open parenthesis
+ raw_dump_table(__func__, "raw skb data dump uncompressed",
+ skb->data, skb->len);
CHECK: Alignment should match open parenthesis
+ err = uncompress_addr(skb, &hdr.saddr, tmp, saddr,
+ saddr_type, saddr_len);
CHECK: Alignment should match open parenthesis
+ err = uncompress_addr(skb, &hdr.daddr, tmp, daddr,
+ daddr_type, daddr_len);
CHECK: Alignment should match open parenthesis
+ pr_debug("dest: stateless compression mode %d dest %pI6c\n",
+ tmp, &hdr.daddr);
CHECK: Alignment should match open parenthesis
+ raw_dump_table(__func__, "raw UDP header dump",
+ (u8 *)&uh, sizeof(uh));
CHECK: Alignment should match open parenthesis
+ raw_dump_table(__func__, "raw header dump", (u8 *)&hdr,
+ sizeof(hdr));
CHECK: Alignment should match open parenthesis
+int lowpan_header_compress(struct sk_buff *skb, struct net_device *dev,
+ unsigned short type, const void *_daddr,
CHECK: Alignment should match open parenthesis
+ raw_dump_table(__func__, "raw skb network header dump",
+ skb_network_header(skb), sizeof(struct ipv6hdr));
CHECK: Alignment should match open parenthesis
+ raw_dump_table(__func__,
+ "sending raw skb network uncompressed packet",
CHECK: Alignment should match open parenthesis
+ if (((hdr->flow_lbl[0] & 0x0F) == 0) &&
+ (hdr->flow_lbl[1] == 0) && (hdr->flow_lbl[2] == 0)) {
WARNING: quoted string split across lines
+ pr_debug("dest address unicast link-local %pI6c "
+ "iphc1 0x%02x\n", &hdr->daddr, iphc1);
CHECK: Alignment should match open parenthesis
+ raw_dump_table(__func__, "raw skb data dump compressed",
+ skb->data, skb->len);
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch fixes all the block comment issues found by checkpatch.pl and
makes them match the network style now.
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+/*
+ * Based on patches from Jon Smirl <jonsmirl@gmail.com>
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+/*
+ * Uncompress address function for source and
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+/*
+ * Uncompress address function for source context
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+ /*
+ * UDP lenght needs to be infered from the lower layers
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+ /*
+ * Traffic Class and FLow Label carried in-line
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+ /*
+ * Traffic class carried in-line
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+ /*
+ * Flow Label carried in-line
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+ /*
+ * replace the compressed UDP head by the uncompressed UDP
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+ /*
+ * As we copy some bit-length fields, in the IPHC encoding bytes,
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+ /*
+ * Traffic class, flow label
WARNING: networking block comments don't use an empty /* line, use /* Comment...
+ /*
+ * Hop limit
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This memory is placed on stack and can't be null so remove the check on
null.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the own implementation to check of link-layer,
broadcast and any address type and use the IPv6 api for that.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch uses the lowpan_push_hc_data functions in several places
where we can use it. The lowpan_push_hc_data was introduced in some
previous patches.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We introduced the lowpan_fetch_skb function in some previous patches for
6lowpan to have a generic fetch function. This patch drops the old
function and use the generic lowpan_fetch_skb one.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hc06_ptr pointer variable stands for header compression draft-06. We
are mostly rfc complaint. This patch rename the variable to normal hc_ptr.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
NFNL_MSG_ACCT_GET_CTRZERO modifies dumped flags, in this case
client see unmodified (uncleared) counter value and cleared
overquota state - end user doesn't know anything about overquota state,
unless end user subscribed on overquota report.
Signed-off-by: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The synchronous syncrhonize_rcu in switch_task_namespaces makes setns
a sufficiently expensive system call that people have complained.
Upon inspect nsproxy no longer needs rcu protection for remote reads.
remote reads are rare. So optimize for same process reads and write
by switching using rask_lock instead.
This yields a simpler to understand lock, and a faster setns system call.
In particular this fixes a performance regression observed
by Rafael David Tinoco <rafael.tinoco@canonical.com>.
This is effectively a revert of Pavel Emelyanov's commit
cf7b708c8d Make access to task's nsproxy lighter
from 2007. The race this originialy fixed no longer exists as
do_notify_parent uses task_active_pid_ns(parent) instead of
parent->nsproxy.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Sparse warns because of implicit pointer cast.
v2: subject line correction, space between "void" and "*"
Signed-off-by: Karoly Kemeny <karoly.kemeny@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of the macro IS_ERR_OR_NULL in place of
tests for NULL and IS_ERR.
The following Coccinelle semantic patch was used for making the change:
@@
expression e;
@@
- e == NULL || IS_ERR(e)
+ IS_ERR_OR_NULL(e)
|| ...
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of the macro IS_ERR_OR_NULL in place of
tests for NULL and IS_ERR.
The following Coccinelle semantic patch was used for making the change:
@@
expression e;
@@
- e == NULL || IS_ERR(e)
+ IS_ERR_OR_NULL(e)
|| ...
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of the macro IS_ERR_OR_NULL in place of
tests for NULL and IS_ERR.
The following Coccinelle semantic patch was used for making the change:
@@
expression e;
@@
- e == NULL || IS_ERR(e)
+ IS_ERR_OR_NULL(e)
|| ...
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If requests are queued in the socket inbuffer waiting for an
svc_tcp_has_wspace() requirement to be satisfied, then we do not want
to clear the SOCK_NOSPACE flag until we've satisfied that requirement.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Ensure that all calls to svc_xprt_enqueue() except svc_xprt_received()
check the value of XPT_BUSY, before attempting to grab spinlocks etc.
This is to avoid situations such as the following "perf" trace,
which shows heavy contention on the pool spinlock:
54.15% nfsd [kernel.kallsyms] [k] _raw_spin_lock_bh
|
--- _raw_spin_lock_bh
|
|--71.43%-- svc_xprt_enqueue
| |
| |--50.31%-- svc_reserve
| |
| |--31.35%-- svc_xprt_received
| |
| |--18.34%-- svc_tcp_data_ready
...
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Sasha's report:
> While fuzzing with trinity inside a KVM tools guest running the latest -next
> kernel with the KASAN patchset, I've stumbled on the following spew:
>
> [ 4448.949424] ==================================================================
> [ 4448.951737] AddressSanitizer: user-memory-access on address 0
> [ 4448.952988] Read of size 2 by thread T19638:
> [ 4448.954510] CPU: 28 PID: 19638 Comm: trinity-c76 Not tainted 3.16.0-rc4-next-20140711-sasha-00046-g07d3099-dirty #813
> [ 4448.956823] ffff88046d86ca40 0000000000000000 ffff880082f37e78 ffff880082f37a40
> [ 4448.958233] ffffffffb6e47068 ffff880082f37a68 ffff880082f37a58 ffffffffb242708d
> [ 4448.959552] 0000000000000000 ffff880082f37a88 ffffffffb24255b1 0000000000000000
> [ 4448.961266] Call Trace:
> [ 4448.963158] dump_stack (lib/dump_stack.c:52)
> [ 4448.964244] kasan_report_user_access (mm/kasan/report.c:184)
> [ 4448.965507] __asan_load2 (mm/kasan/kasan.c:352)
> [ 4448.966482] ? netlink_sendmsg (net/netlink/af_netlink.c:2339)
> [ 4448.967541] netlink_sendmsg (net/netlink/af_netlink.c:2339)
> [ 4448.968537] ? get_parent_ip (kernel/sched/core.c:2555)
> [ 4448.970103] sock_sendmsg (net/socket.c:654)
> [ 4448.971584] ? might_fault (mm/memory.c:3741)
> [ 4448.972526] ? might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3740)
> [ 4448.973596] ? verify_iovec (net/core/iovec.c:64)
> [ 4448.974522] ___sys_sendmsg (net/socket.c:2096)
> [ 4448.975797] ? put_lock_stats.isra.13 (./arch/x86/include/asm/preempt.h:98 kernel/locking/lockdep.c:254)
> [ 4448.977030] ? lock_release_holdtime (kernel/locking/lockdep.c:273)
> [ 4448.978197] ? lock_release_non_nested (kernel/locking/lockdep.c:3434 (discriminator 1))
> [ 4448.979346] ? check_chain_key (kernel/locking/lockdep.c:2188)
> [ 4448.980535] __sys_sendmmsg (net/socket.c:2181)
> [ 4448.981592] ? trace_hardirqs_on_caller (kernel/locking/lockdep.c:2600)
> [ 4448.982773] ? trace_hardirqs_on (kernel/locking/lockdep.c:2607)
> [ 4448.984458] ? syscall_trace_enter (arch/x86/kernel/ptrace.c:1500 (discriminator 2))
> [ 4448.985621] ? trace_hardirqs_on_caller (kernel/locking/lockdep.c:2600)
> [ 4448.986754] SyS_sendmmsg (net/socket.c:2201)
> [ 4448.987708] tracesys (arch/x86/kernel/entry_64.S:542)
> [ 4448.988929] ==================================================================
This reports means that we've come to netlink_sendmsg() with msg->msg_name == NULL and msg->msg_namelen > 0.
After this report there was no usual "Unable to handle kernel NULL pointer dereference"
and this gave me a clue that address 0 is mapped and contains valid socket address structure in it.
This bug was introduced in f3d3342602
(net: rework recvmsg handler msg_name and msg_namelen logic).
Commit message states that:
"Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address."
But in fact this affects sendto when address 0 is mapped and contains
socket address structure in it. In such case copy-in address will succeed,
verify_iovec() function will successfully exit with msg->msg_namelen > 0
and msg->msg_name == NULL.
This patch fixes it by setting msg_namelen to 0 if msg_name == NULL.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: <stable@vger.kernel.org>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly, vlan will create /proc/net/vlan/<dev>, so when we
create dev with name "config", it will confict with
/proc/net/vlan/config.
Reported-by: Stephane Chazelas <stephane.chazelas@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create a proc dir for each network device, this will cause
conflicts when the devices have name "all" or "default".
Rather than emitting an ugly kernel warning, we could just
fail earlier by checking the device name.
Reported-by: Stephane Chazelas <stephane.chazelas@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create a proc dir for each network device, this will cause
conflicts when the devices have name "all" or "default".
Rather than emitting an ugly kernel warning, we could just
fail earlier by checking the device name.
Reported-by: Stephane Chazelas <stephane.chazelas@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SO_TIMESTAMPING API defines three types of timestamps: software,
hardware in raw format (hwtstamp) and hardware converted to system
format (syststamp). The last has been deprecated in favor of combining
hwtstamp with a PTP clock driver. There are no active users in the
kernel.
The option was device driver dependent. If set, but without hardware
support, the correct behavior is to return zero in the relevant field
in the SCM_TIMESTAMPING ancillary message. Without device drivers
implementing the option, this field is effectively always zero.
Remove the internal plumbing to dissuage new drivers from implementing
the feature. Keep the SOF_TIMESTAMPING_SYS_HARDWARE flag, however, to
avoid breaking existing applications that request the timestamp.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No device driver will ever return an skb_shared_info structure with
syststamp non-zero, so remove the branch that tests for this and
optionally marks the packet timestamp as TP_STATUS_TS_SYS_HARDWARE.
Do not remove the definition TP_STATUS_TS_SYS_HARDWARE, as processes
may refer to it.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 3.17.
This is a rather quiet one, we have:
- A new driver from ST Microelectronics for their NCI ST21NFCB,
including device tree support.
- p2p support for the ST21NFCA driver
- A few fixes an enhancements for the NFC digital layer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wR0y
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.17 pull request
This is the NFC pull request for 3.17.
This is a rather quiet one, we have:
- A new driver from ST Microelectronics for their NCI ST21NFCB,
including device tree support.
- p2p support for the ST21NFCA driver
- A few fixes an enhancements for the NFC digital layer"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "Counting Packets Sent Between Arbitrary Internet Hosts", Jeffrey and
Jedidiah describe ways exploiting linux IP identifier generation to
infer whether two machines are exchanging packets.
With commit 73f156a6e8 ("inetpeer: get rid of ip_id_count"), we
changed IP id generation, but this does not really prevent this
side-channel technique.
This patch adds a random amount of perturbation so that IP identifiers
for a given destination [1] are no longer monotonically increasing after
an idle period.
Note that prandom_u32_max(1) returns 0, so if generator is used at most
once per jiffy, this patch inserts no hole in the ID suite and do not
increase collision probability.
This is jiffies based, so in the worst case (HZ=1000), the id can
rollover after ~65 seconds of idle time, which should be fine.
We also change the hash used in __ip_select_ident() to not only hash
on daddr, but also saddr and protocol, so that ICMP probes can not be
used to infer information for other protocols.
For IPv6, adds saddr into the hash as well, but not nexthdr.
If I ping the patched target, we can see ID are now hard to predict.
21:57:11.008086 IP (...)
A > target: ICMP echo request, seq 1, length 64
21:57:11.010752 IP (... id 2081 ...)
target > A: ICMP echo reply, seq 1, length 64
21:57:12.013133 IP (...)
A > target: ICMP echo request, seq 2, length 64
21:57:12.015737 IP (... id 3039 ...)
target > A: ICMP echo reply, seq 2, length 64
21:57:13.016580 IP (...)
A > target: ICMP echo request, seq 3, length 64
21:57:13.019251 IP (... id 3437 ...)
target > A: ICMP echo reply, seq 3, length 64
[1] TCP sessions uses a per flow ID generator not changed by this patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jeffrey Knockel <jeffk@cs.unm.edu>
Reported-by: Jedidiah R. Crandall <crandall@cs.unm.edu>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per comment from David Miller, we try to make the buffer reassembly
function more resilient to user errors than it is today.
- We check that the "*buf" parameter always is set, since this is
mandatory input.
- We ensure that *buf->next always is set to NULL before linking in
the buffer, instead of relying of the caller to have done this.
- We ensure that the "tail" pointer in the head buffer's control
block is initialized to NULL when the first fragment arrives.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndm_type means L3 address type, in neighbour proxy and vxlan, it's RTN_UNICAST.
NDA_DST is for netlink TLV type, hence it's not right value in this context.
Signed-off-by: Jun Zhao <mypopydev@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-07-25
Please pull this batch of updates intended for the 3.17 stream!
For the mac80211 bits, Johannes says:
"We have a lot of TDLS patches, among them a fix that should make hwsim
tests happy again. The rest, this time, is mostly small fixes."
For the Bluetooth bits, Gustavo says:
"Some more patches for 3.17. The most important change here is the move of
the 6lowpan code to net/6lowpan. It has been agreed with Davem that this
change will go through the bluetooth tree. The rest are mostly clean up and
fixes."
and,
"Here follows some more patches for 3.17. These are mostly fixes to what
we've sent to you before for next merge window."
For the iwlwifi bits, Emmanuel says:
"I have the usual amount of BT Coex stuff. Arik continues to work
on TDLS and Ariej contributes a few things for HS2.0. I added a few
more things to the firmware debugging infrastructure. Eran fixes a
small bug - pretty normal content."
And for the Atheros bits, Kalle says:
"For ath6kl me and Jessica added support for ar6004 hw3.0, our latest
version of ar6004.
For ath10k Janusz added a printout so that it's easier to check what
ath10k kconfig options are enabled. He also added a debugfs file to
configure maximum amsdu and ampdu values. Also we had few fixes as
usual."
On top of that is the usual large batch of various driver updates --
brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action.
Rafał has also been very busy with b43 and related updates.
Also, I pulled the wireless tree into this in order to resolve a
merge conflict...
P.S. The change to fs/compat_ioctl.c reflects a name change in a
Bluetooth header file...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have entries in the whitelist we shouldn't disable page scanning
when disabling connectable mode. This patch adds the necessary check to
the Set Connectable command handler.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes a typo in the hci_cc_write_scan_enable() function where
we want to clear the HCI_PSCAN flag if the SCAN_PAGE bit of the HCI
command parameter was not set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes init_net's high_thresh limit to be the maximum for all
namespaces, thus introducing a global memory limit threshold equal to the
sum of the individual high_thresh limits which are capped.
It also introduces some sane minimums for low_thresh as it shouldn't be
able to drop below 0 (or > high_thresh in the unsigned case), and
overall low_thresh should not ever be above high_thresh, so we make the
following relations for a namespace:
init_net:
high_thresh - max(not capped), min(init_net low_thresh)
low_thresh - max(init_net high_thresh), min (0)
all other namespaces:
high_thresh = max(init_net high_thresh), min(namespace's low_thresh)
low_thresh = max(namespace's high_thresh), min(0)
The major issue with having low_thresh > high_thresh is that we'll
schedule eviction but never evict anything and thus rely only on the
timers.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rehash is rare operation, don't force readers to take
the read-side rwlock.
Instead, we only have to detect the (rare) case where
the secret was altered while we are trying to insert
a new inetfrag queue into the table.
If it was changed, drop the bucket lock and recompute
the hash to get the 'new' chain bucket that we have to
insert into.
Joint work with Nikolay Aleksandrov.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
merge functionality into the eviction workqueue.
Instead of rebuilding every n seconds, take advantage of the upper
hash chain length limit.
If we hit it, mark table for rebuild and schedule workqueue.
To prevent frequent rebuilds when we're completely overloaded,
don't rebuild more than once every 5 seconds.
ipfrag_secret_interval sysctl is now obsolete and has been marked as
deprecated, it still can be changed so scripts won't be broken but it
won't have any effect. A comment is left above each unused secret_timer
variable to avoid confusion.
Joint work with Nikolay Aleksandrov.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'nqueues' counter is protected by the lru list lock,
once thats removed this needs to be converted to atomic
counter. Given this isn't used for anything except for
reporting it to userspace via /proc, just remove it.
We still report the memory currently used by fragment
reassembly queues.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the high_thresh limit is reached we try to toss the 'oldest'
incomplete fragment queues until memory limits are below the low_thresh
value. This happens in softirq/packet processing context.
This has two drawbacks:
1) processors might evict a queue that was about to be completed
by another cpu, because they will compete wrt. resource usage and
resource reclaim.
2) LRU list maintenance is expensive.
But when constantly overloaded, even the 'least recently used' element is
recent, so removing 'lru' queue first is not 'fairer' than removing any
other fragment queue.
This moves eviction out of the fast path:
When the low threshold is reached, a work queue is scheduled
which then iterates over the table and removes the queues that exceed
the memory limits of the namespace. It sets a new flag called
INET_FRAG_EVICTED on the evicted queues so the proper counters will get
incremented when the queue is forcefully expired.
When the high threshold is reached, no more fragment queues are
created until we're below the limit again.
The LRU list is now unused and will be removed in a followup patch.
Joint work with Nikolay Aleksandrov.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step to move eviction handling into a work queue.
We lose two spots that accounted evicted fragments in MIB counters.
Accounting will be restored since the upcoming work-queue evictor
invokes the frag queue timer callbacks instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
hide actual hash size from individual users: The _find
function will now fold the given hash value into the required range.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the Bluetooth 4.1 specification the Simultaneous LE and BR/EDR
controller option has been deprecated. It shall be set to zero and
ignored otherwise.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Expose the default values for minimum and maximum LE advertising
interval via debugfs for testing purposes.
Signed-off-by: Georg Lukas <georg@op-co.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Store the default values for minimum and maximum advertising interval
with all the other controller defaults. These vaules are sent to the
adapter whenever advertising is (re)enabled.
Signed-off-by: Georg Lukas <georg@op-co.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Devices using resolvable private addresses are required to provide
an identity resolving key. These devices can not be found using
the current controller white list support. This means if the kernel
knows about any devices with an identity resolving key, the white
list filtering must be disabled.
However so far the kernel kept identity resolving keys around even
for devices that are not using resolvable private addresses. The
notification to userspace clearly hints to not store the key and
so it is best to just remove the key from the kernel as well at
that point.
With this it easy now to detect when using the white list is
possible or when kernel side resolving of addresses is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controller can use a white list filter when scanning
to avoid waking up the host for devices that are of no interest.
Devices marked as reporting, direct connection (incoming) or general
connection are now added to the controller white list. The update of
the white list happens just before enabling passive scanning.
In case the white list is full and can not hold all devices, the
white list is not used and the filter policy set to accept all
advertisements.
Using the white list for scanning allows for power saving with
controllers that do not handle the duplicate filtering correctly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If led-always-blink is set, then between switch led OFF and ON
is almost zero time. So blink is invisible. This use oneshot led trigger
with fixed time 50ms witch is enough to see blink.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The ulog targets were recently killed. A few references to the Kconfig
macros CONFIG_IP_NF_TARGET_ULOG and CONFIG_BRIDGE_EBT_ULOG were left
untouched. Kill these too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The function led_trigger_register() will only return -EEXIST when
error arises.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In this file, function names are otherwise used as pointers without &.
A simplified version of the Coccinelle semantic patch that makes this
change is as follows:
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After 11878b40e[net-timestamp: SOCK_RAW and PING timestamping], this comment
becomes obsolete since the codes check not only UDP socket, but also RAW sock;
and the codes are clear, not need the comments
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"net" is normally for struct net*, pointer to struct net_device
should be named to either "dev" or "ndev" etc.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF is used by socket filtering, seccomp and soon by tracing and
exposed to userspace, therefore 'sock_filter_int' name is not accurate.
Rename it to 'bpf_insn'
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the Coccinelle semantic patch that makes this
change is as follows:
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the Coccinelle semantic patch that makes this
change is as follows:
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the Coccinelle semantic patch that makes this
change is as follows:
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-07-24
Please pull this batch of fixes intended for the 3.16 stream...
For the mac80211 fixes, Johannes says:
"I have two fixes: one for tracing that fixes a long-standing NULL
pointer dereference, and one for a mac80211 issue that causes iwlmvm to
send invalid frames during authentication/association."
and,
"One more fix - for a bug in the newly introduced code that obtains rate
control information for stations."
For the iwlwifi fixes, Emmanuel says:
"It includes a merge damage fix. This region has been changed in -next
and -fixes quite a few times and apparently, I failed to handle it
properly, so here the fix. Along with that I have a fix from Eliad
to properly handle overlapping BSS in AP mode."
On top of that, Felix provides and ath9k fix for Tx stalls that happen
after an aggregation session failure.
Please let me know if there are problems! There are some changes
here that will cause merge conflicts in -next. Once you merge this
I can pull it into wireless-next and resolve those issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Via Simon Horman, I received the following one-liner for your net tree:
1) Fix crash when exiting from netns that uses IPVS and conntrack,
from Julian Anastasov via Simon Horman.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug where skb_clone() NULL check is missing in sample action
implementation.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
The sample action is rather generic, allowing arbitrary actions to be
executed based on a probability. However its use, within the Open
vSwitch
code-base is limited: only a single user-space action is ever nested.
A consequence of the current implementation of sample actions is that
depending on weather the sample action executed (due to its probability)
any side-effects of nested actions may or may not be present before
executing subsequent actions. This has the potential to complicate
verification of valid actions by the (kernel) datapath. And indeed
adding support for push and pop MPLS actions inside sample actions
is one case where such case.
In order to allow all supported actions to be continue to be nested
inside sample actions without the potential need for complex
verification code this patch changes the implementation of the sample
action in the kernel datapath so that sample actions are more like
a function call and any side effects of nested actions are not
present when executing subsequent actions.
With the above in mind the motivation for this change is twofold:
* To contain side-effects the sample action in the hope of making it
easier to deal with in the future and;
* To avoid some rather complex verification code introduced in the MPLS
datapath patch.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
In queue_userspace_packet(), the ovs_nla_put_flow return value is
not checked. This is fine as long as key_attr_size() returns the
correct value. In case it does not, the current code may corrupt buffer
memory. Add a run time assertion catch this case to avoid silent
failure.
Reported-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
xt_hashlimit cannot be used with large hash tables, because garbage
collector is run from a timer. If table is really big, its possible
to hold cpu for more than 500 msec, which is unacceptable.
Switch to a work queue, and use proper scheduling points to remove
latencies spikes.
Later, we also could switch to a smoother garbage collection done
at lookup time, one bucket at a time...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Following patch enables all available tunnel GSO features for OVS
bridge device so that ovs can use hardware offloads available to
underling device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
In order to allow handlers directly read upcalls from datapath,
we need to support per-handler netlink socket for each vport in
datapath. This commit makes this happen. Also, it is guaranteed
to be backward compatible with previous branch.
Signed-off-by: Alex Wang <alexw@nicira.com>
Acked-by: Thomas Graf <tgraf@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Steffen Klassert says:
====================
pull request (net): ipsec 2014-07-23
Just two fixes this time, both are stable candidates.
1) Fix the dst_entry refcount on socket policy usage.
2) Fix a wrong SPI check that prevents AH SAs from getting
installed, dependent on the SPI. From Tobias Brunner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF is used in several kernel components. This split creates logical boundary
between generic eBPF core and the rest
kernel/bpf/core.c: eBPF interpreter
net/core/filter.c: classic->eBPF converter, classic verifiers, socket filters
This patch only moves functions.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, although IP_MULTICAST_ALL and IP_MSFILTER ioctl calls succeed on
raw sockets, there is no code to implement the functionality on received
packets; it is only implemented for UDP sockets. The raw(7) man page states:
"In addition, all ip(7) IPPROTO_IP socket options valid for datagram sockets
are supported", which implies these ioctls should work on raw sockets.
To fix this, add a call to ip_mc_sf_allow on raw sockets.
This should not break any existing code, since the current position of
not calling ip_mc_sf_filter makes it behave as if neither the IP_MULTICAST_ALL
nor the IP_MSFILTER ioctl had been called. Adding the call to ip_mc_sf_allow
will therefore maintain the current behaviour so long as IP_MULTICAST_ALL and
IP_MSFILTER ioctls are not called. Any code that currently is calling
IP_MULTICAST_ALL or IP_MSFILTER ioctls on raw sockets presumably is wanting
the filter to be applied, although no filtering will currently be occurring.
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding remote devices to the kernel using the Add Device management
command, these devices are explicitly allowed to connect. This kind of
incoming connections are possible even when the controller itself is
not connectable.
For BR/EDR this distinction is pretty simple since there is only one
type of incoming connections. With LE this is not that simple anymore
since there are ADV_IND and ADV_DIRECT_IND advertising events.
The ADV_DIRECT_IND advertising events are send for incoming (slave
initiated) connections only. And this is the only thing the kernel
should allow when adding devices using action 0x01. This meaning
of incoming connections is coming from BR/EDR and needs to be
mapped to LE the same way.
Supporting the auto-connection of devices using ADV_IND advertising
events is an important feature as well. However it does not map to
incoming connections. So introduce a new action 0x02 that allows
the kernel to connect to devices using ADV_DIRECT_IND and in addition
ADV_IND advertising reports.
This difference is represented by the new HCI_AUTO_CONN_DIRECT value
for only connecting to ADV_DIRECT_IND. For connection to ADV_IND and
ADV_DIRECT_IND the old value HCI_AUTO_CONN_ALWAYS is used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Unconditionally connecting to devices sending ADV_DIRECT_IND when
the controller is in CONNECTABLE mode is a feature that is not
fully working. The background scanning trigger for this has been
removed, but the statement allowing it to happen in case some
other part triggers is still present. So remove that code part
as well to avoid unwanted connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It hasn't been used since commit 0fd7bac(net: relax rcvbuf limits).
Signed-off-by: Sorin Dumitru <sorin@returnze.ro>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the Bluetooth controller supports Get MWS Transport Layer
Configuration command, then issue it during initialization.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the Bluetooth controller supports Read Local Supported Codecs
command, then issue it during initialization so that the list of
codecs is known.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Jason reported an oops caused by SCTP on his ARM machine with
SCTP authentication enabled:
Internal error: Oops: 17 [#1] ARM
CPU: 0 PID: 104 Comm: sctp-test Not tainted 3.13.0-68744-g3632f30c9b20-dirty #1
task: c6eefa40 ti: c6f52000 task.ti: c6f52000
PC is at sctp_auth_calculate_hmac+0xc4/0x10c
LR is at sg_init_table+0x20/0x38
pc : [<c024bb80>] lr : [<c00f32dc>] psr: 40000013
sp : c6f538e8 ip : 00000000 fp : c6f53924
r10: c6f50d80 r9 : 00000000 r8 : 00010000
r7 : 00000000 r6 : c7be4000 r5 : 00000000 r4 : c6f56254
r3 : c00c8170 r2 : 00000001 r1 : 00000008 r0 : c6f1e660
Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005397f Table: 06f28000 DAC: 00000015
Process sctp-test (pid: 104, stack limit = 0xc6f521c0)
Stack: (0xc6f538e8 to 0xc6f54000)
[...]
Backtrace:
[<c024babc>] (sctp_auth_calculate_hmac+0x0/0x10c) from [<c0249af8>] (sctp_packet_transmit+0x33c/0x5c8)
[<c02497bc>] (sctp_packet_transmit+0x0/0x5c8) from [<c023e96c>] (sctp_outq_flush+0x7fc/0x844)
[<c023e170>] (sctp_outq_flush+0x0/0x844) from [<c023ef78>] (sctp_outq_uncork+0x24/0x28)
[<c023ef54>] (sctp_outq_uncork+0x0/0x28) from [<c0234364>] (sctp_side_effects+0x1134/0x1220)
[<c0233230>] (sctp_side_effects+0x0/0x1220) from [<c02330b0>] (sctp_do_sm+0xac/0xd4)
[<c0233004>] (sctp_do_sm+0x0/0xd4) from [<c023675c>] (sctp_assoc_bh_rcv+0x118/0x160)
[<c0236644>] (sctp_assoc_bh_rcv+0x0/0x160) from [<c023d5bc>] (sctp_inq_push+0x6c/0x74)
[<c023d550>] (sctp_inq_push+0x0/0x74) from [<c024a6b0>] (sctp_rcv+0x7d8/0x888)
While we already had various kind of bugs in that area
ec0223ec48 ("net: sctp: fix sctp_sf_do_5_1D_ce to verify if
we/peer is AUTH capable") and b14878ccb7 ("net: sctp: cache
auth_enable per endpoint"), this one is a bit of a different
kind.
Giving a bit more background on why SCTP authentication is
needed can be found in RFC4895:
SCTP uses 32-bit verification tags to protect itself against
blind attackers. These values are not changed during the
lifetime of an SCTP association.
Looking at new SCTP extensions, there is the need to have a
method of proving that an SCTP chunk(s) was really sent by
the original peer that started the association and not by a
malicious attacker.
To cause this bug, we're triggering an INIT collision between
peers; normal SCTP handshake where both sides intent to
authenticate packets contains RANDOM; CHUNKS; HMAC-ALGO
parameters that are being negotiated among peers:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
-------------------- COOKIE-ECHO -------------------->
<-------------------- COOKIE-ACK ---------------------
RFC4895 says that each endpoint therefore knows its own random
number and the peer's random number *after* the association
has been established. The local and peer's random number along
with the shared key are then part of the secret used for
calculating the HMAC in the AUTH chunk.
Now, in our scenario, we have 2 threads with 1 non-blocking
SEQ_PACKET socket each, setting up common shared SCTP_AUTH_KEY
and SCTP_AUTH_ACTIVE_KEY properly, and each of them calling
sctp_bindx(3), listen(2) and connect(2) against each other,
thus the handshake looks similar to this, e.g.:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
<--------- INIT[RANDOM; CHUNKS; HMAC-ALGO] -----------
-------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] -------->
...
Since such collisions can also happen with verification tags,
the RFC4895 for AUTH rather vaguely says under section 6.1:
In case of INIT collision, the rules governing the handling
of this Random Number follow the same pattern as those for
the Verification Tag, as explained in Section 5.2.4 of
RFC 2960 [5]. Therefore, each endpoint knows its own Random
Number and the peer's Random Number after the association
has been established.
In RFC2960, section 5.2.4, we're eventually hitting Action B:
B) In this case, both sides may be attempting to start an
association at about the same time but the peer endpoint
started its INIT after responding to the local endpoint's
INIT. Thus it may have picked a new Verification Tag not
being aware of the previous Tag it had sent this endpoint.
The endpoint should stay in or enter the ESTABLISHED
state but it MUST update its peer's Verification Tag from
the State Cookie, stop any init or cookie timers that may
running and send a COOKIE ACK.
In other words, the handling of the Random parameter is the
same as behavior for the Verification Tag as described in
Action B of section 5.2.4.
Looking at the code, we exactly hit the sctp_sf_do_dupcook_b()
case which triggers an SCTP_CMD_UPDATE_ASSOC command to the
side effect interpreter, and in fact it properly copies over
peer_{random, hmacs, chunks} parameters from the newly created
association to update the existing one.
Also, the old asoc_shared_key is being released and based on
the new params, sctp_auth_asoc_init_active_key() updated.
However, the issue observed in this case is that the previous
asoc->peer.auth_capable was 0, and has *not* been updated, so
that instead of creating a new secret, we're doing an early
return from the function sctp_auth_asoc_init_active_key()
leaving asoc->asoc_shared_key as NULL. However, we now have to
authenticate chunks from the updated chunk list (e.g. COOKIE-ACK).
That in fact causes the server side when responding with ...
<------------------ AUTH; COOKIE-ACK -----------------
... to trigger a NULL pointer dereference, since in
sctp_packet_transmit(), it discovers that an AUTH chunk is
being queued for xmit, and thus it calls sctp_auth_calculate_hmac().
Since the asoc->active_key_id is still inherited from the
endpoint, and the same as encoded into the chunk, it uses
asoc->asoc_shared_key, which is still NULL, as an asoc_key
and dereferences it in ...
crypto_hash_setkey(desc.tfm, &asoc_key->data[0], asoc_key->len)
... causing an oops. All this happens because sctp_make_cookie_ack()
called with the *new* association has the peer.auth_capable=1
and therefore marks the chunk with auth=1 after checking
sctp_auth_send_cid(), but it is *actually* sent later on over
the then *updated* association's transport that didn't initialize
its shared key due to peer.auth_capable=0. Since control chunks
in that case are not sent by the temporary association which
are scheduled for deletion, they are issued for xmit via
SCTP_CMD_REPLY in the interpreter with the context of the
*updated* association. peer.auth_capable was 0 in the updated
association (which went from COOKIE_WAIT into ESTABLISHED state),
since all previous processing that performed sctp_process_init()
was being done on temporary associations, that we eventually
throw away each time.
The correct fix is to update to the new peer.auth_capable
value as well in the collision case via sctp_assoc_update(),
so that in case the collision migrated from 0 -> 1,
sctp_auth_asoc_init_active_key() can properly recalculate
the secret. This therefore fixes the observed server panic.
Fixes: 730fc3d05c ("[SCTP]: Implete SCTP-AUTH parameter processing")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The digital layer of the NFC subsystem currently
supports a 'tg_listen_mdaa' driver hook that supports
devices that can do mode detection and automatic
anticollision. However, there are some devices that
can do mode detection but not automatic anitcollision
so add the 'tg_listen_md' hook to support those devices.
In order for the digital layer to get the RF technology
detected by the device from the driver, add the
'tg_get_rf_tech' hook. It is only valid to call this
hook immediately after a successful call to 'tg_listen_md'.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
stop_poll allows to stop CLF reader polling. Some other operations might be
necessary for some CLF to stop polling. For example in card mode.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add T1T matching with Jewel during notification.
It was causing "the target found does not have the desired protocol"
to show up.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make use of key preparsing in the RxRPC protocol so that quota size
determination can take place prior to keyring locking when a key is being
added.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Steve Dickson <steved@redhat.com>
Make use of key preparsing in the DNS resolver so that quota size determination
can take place prior to keyring locking when a key is being added.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Steve Dickson <steved@redhat.com>
Acked-by: Jeff Layton <jlayton@primarydata.com>
Ceph can use user_match() instead of defining its own identical function.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Steve Dickson <steved@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
cc: Tommi Virtanen <tommi.virtanen@dreamhost.com>
Make use of key preparsing in Ceph so that quota size determination can take
place prior to keyring locking when a key is being added.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Steve Dickson <steved@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
cc: Tommi Virtanen <tommi.virtanen@dreamhost.com>
See RFC 5666 section 3.7: clients don't have to send zero XDR
padding.
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=246
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
MSG_MORE and 'corking' a socket would require that the transmit of
a data chunk be delayed.
Rename the return value to be less specific.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for Nagle contains 6 separate checks all of which must be true
before a data packet is delayed.
Separate out each into its own 'if (test) return SCTP_XMIT_OK' so that
the reasons can be individually described.
Also return directly with SCTP_XMIT_RWND_FULL.
Delete the now-unused 'retval' variable and 'finish' label from
sctp_packet_can_append_data().
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the expected throughput is queried before rate control has been
initialized, the minstrel op for it will crash while trying to access
the rate table.
Check for WLAN_STA_RATE_CONTROL before attempting to use the rate
control op.
Reported-by: Jean-Pierre Tosoni <jp.tosoni@acksys.fr>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commits 08c30aca9e "Bluetooth: Remove
RFCOMM session refcnt" and 8ff52f7d04
"Bluetooth: Return RFCOMM session ptrs to avoid freed session"
allow rfcomm_recv_ua and rfcomm_session_close to delete the session
(and free the corresponding socket) and propagate NULL session pointer
to the upper callers.
Additional fix is required to terminate the loop in rfcomm_process_rx
function to avoid use of freed 'sk' memory.
The issue is only reproducible with kernel option CONFIG_PAGE_POISONING
enabled making freed memory being changed and filled up with fixed char
value used to unmask use-after-free issues.
Signed-off-by: Vignesh Raman <Vignesh_Raman@mentor.com>
Signed-off-by: Vitaly Kuzmichev <Vitaly_Kuzmichev@mentor.com>
Acked-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
This patch uses the cb->data pointer that allows us to store the
context when dumping the set list. Thus, we don't need to parse the
original netlink message containing the dump request for each recvmsg()
call when dumping the set list. The different function flavours
depending on the dump criteria has been also merged into one single
generic function. This saves us ~100 lines of code.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
So you can reject IPv4 and IPv6 packets from bridge tables. If the ether
proto is now known, default on dropping the packet instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
drivers/infiniband/hw/cxgb4/device.c
The cxgb4 conflict was simply overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
An af_iucv stress test showed -EPIPE results for sendmsg()
calls. They are caused by quiescing a path even though it has
been already severed by peer. For IUCV transport shutdown()
consists of 2 steps:
(1) sending the shutdown message to peer
(2) quiescing the iucv path
If the iucv path between these 2 steps is severed due to peer
closing the path, the quiesce step is no longer needed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Reported-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- recognise and drop Bridge Loop Avoidance packets even if
they are encapsulated in the 802.1q header multiple times.
Forwarding them into the mesh creates issues on other
nodes.
- properly handle VLAN private objects in order to avoid race
conditions upon fast VLAN deletion-addition. Such conditions
create an unrecoverable inconsistency in the TT database of
the nodes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RdJM
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
pull request [net]: batman-adv 20140721
here you have two fixes that we have been testing for quite some time
(this is why they arrived a bit late in the rc cycle).
Patch 1) ensures that BLA packets get dropped and not forwarded to the
mesh even if they reach batman-adv within QinQ frames. Forwarding them
into the mesh means messing up with the TT database of other nodes which
can generate all kind of unexpected behaviours during route computation.
Patch 2) avoids a couple of race conditions triggered upon fast VLAN
deletion-addition. Such race conditions are pretty dangerous because
they not only create inconsistencies in the TT database of the nodes
in the network, but such scenario is also unrecoverable (unless
nodes are rebooted).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers may be performing most of Tx/Rx
aggregation on their own (e.g. in firmware)
including AddBa/DelBa negotiations but may
otherwise require Rx reordering assistance.
The patch exports 2 new functions for establishing
Rx aggregation sessions in assumption device
driver has taken care of the necessary
negotiations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[fix endian bug]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (e.g. ath10k) report A-MSDU subframes
individually with identical seqno. The A-MPDU Rx
reorder code did not account for that which made
it practically unusable with drivers using
RX_FLAG_AMSDU_MORE because it would end up
dropping a lot of frames resulting in confusion in
upper network transport layers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sdata can't be NULL, and key being NULL is really not possible
unless the code is modified.
The sdata check made a static analyze (klocwork) unhappy because
we would get pointer to local (sdata->local) and only then check
if sdata is non-NULL.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove !key check as well]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's safer practice to use sizeof(*ptr) instead of sizeof(ptr_type) when
allocating memory in case the type changes. This also fixes the
following style of warnings from static analyzers:
CHECK: Prefer kzalloc(sizeof(*ie)...) over kzalloc(sizeof(struct inquiry_entry)...)
+ ie = kzalloc(sizeof(struct inquiry_entry), GFP_KERNEL);
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The NULL pointer access could happen when ieee80211_crypto_hw_decrypt
is called from ieee80211_rx_h_decrypt with the following condition:
1. rx->key->conf.cipher is not WEP, CCMP, TKIP or AES_CMAC
2. rx->sta is NULL
When ieee80211_crypto_hw_decrypt is called, it verifies
rx->sta->cipher_scheme and it will cause Oops if rx->sta is NULL.
This path adds an addirional rx->sta == NULL verification in
ieee80211_crypto_hw_decrypt for this case.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Vlad Yasevich