Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for processing TLV requests/repsonses
from the mfw and upper driver layers respectively. The implementation
reads the requested TLVs from the shared memory, requests the values
from upper layer drivers, populates this info (TLVs) shared memory and
notifies MFW about the TLV values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds required management firmware (MFW) interfaces such as
mailbox commands, TLV types etc.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-05-22
This series contains updates to i40e only.
Jake provides all the changes in this series starting with making it
consistent in how we approach the bit lock. Fixed the reporting of the
VEB statistics and the queue statistics to always return every queue
even if it is not currently in use. Use WARN_ONCE() so that the first
time we end up with an incorrect size we will dump a stack trace and a
message to help highlight the issue early in testing. Folded the fixed
string prefix into the stat string definition. Instead of using a
separate char *p pointer when copying strings, use the data pointer
directly. Added code comments for several of the statistic functions to
better explain the number and ordering of statistics.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
tcp: reduce quickack pressure for ECN
Small patch series changing TCP behavior vs quickack and ECN
First patch is a refactoring, adding parameter to tcp_incr_quickack()
and tcp_enter_quickack_mode() helpers.
Second patch implements the change, lowering number of ACK packets
sent after an ECN event.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ECN signals currently forces TCP to enter quickack mode for
up to 16 (TCP_MAX_QUICKACKS) following incoming packets.
We believe this is not needed, and only sending one immediate ack
for the current packet should be enough.
This should reduce the extra load noticed in DCTCP environments,
after congestion events.
This is part 2 of our effort to reduce pure ACK packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add finer control of the number of ACK packets sent after
ECN events.
This patch is not changing current behavior, it only enables following
change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial net_device implementation used ingress_lock spinlock to synchronize
ingress path of device. This lock was used in both process and bh context.
In some code paths action map lock was obtained while holding ingress_lock.
Commit e1e992e52f ("[NET_SCHED] protect action config/dump from irqs")
modified actions to always disable bh, while using action map lock, in
order to prevent deadlock on ingress_lock in softirq. This lock was removed
from net_device, so disabling bh, while accessing action map, is no longer
necessary.
Replace all action idr spinlock usage with regular calls that do not
disable bh.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net/ipv6: Fix route append and replace use cases
This patch set fixes a few append and replace uses cases for IPv6 and
adds test cases that codifies the expectations of how append and replace
are expected to work. In paricular it allows a multipath route to have
a dev-only nexthop, something Thomas tried to accomplish with commit
edd7ceb782 ("ipv6: Allow non-gateway ECMP for IPv6") which had to be
reverted because of breakage, and to replace an existing FIB entry
with a reject route.
There are a number of inconsistent and surprising aspects to the Linux
API for adding, deleting, replacing and changing FIB entries. For example,
with IPv4 NLM_F_APPEND means insert the route after any existing entries
with the same key (prefix + priority + TOS for IPv4) and NLM_F_CREATE
without the append flag inserts the new route before any existing entries.
IPv6 on the other hand attempts to guess whether a new route should be
appended to an existing one, possibly creating a multipath route, or to
add a new entry after any existing ones. This applies to both the 'append'
(NLM_F_CREATE + NLM_F_APPEND) and 'prepend' (NLM_F_CREATE only) cases
meaning for IPv6 the NLM_F_APPEND is basically ignored. This guessing
whether the route should be added to a multipath route (gateway routes)
or inserted after existing entries (non-gateway based routes) means a
multipath route can not have a dev only nexthop (potentially required in
some cases - tunnels or VRF route leaking for example) and route 'replace'
is a bit adhoc treating gateway based routes and dev-only / reject routes
differently.
This has led to frustration with developers working on routing suites
such as FRR where workarounds such as delete and add are used instead of
replace.
After this patch set there are 2 differences between IPv4 and IPv6:
1. 'ip ro prepend' = NLM_F_CREATE only
IPv4 adds the new route before any existing ones
IPv6 adds new route after any existing ones
2. 'ip ro append' = NLM_F_CREATE|NLM_F_APPEND
IPv4 adds the new route after any existing ones
IPv6 adds the nexthop to existing routes converting to multipath
For the former, there are cases where we want same prefix routes added
after existing ones (e.g., multicast, prefix routes for macvlan when used
for virtual router redundancy). Requiring the APPEND flag to add a new
route to an existing one helps here but is a slight change in behavior
since prepend with gateway routes now create a separate entry.
For the latter IPv6 behavior is preferred - appending a route for the same
prefix and metric to make a multipath route, so really IPv4 not allowing an
existing route to be updated is the limiter. This will be fixed when
nexthops become separate objects - a future patch set.
Thank you to Thomas and Ido for testing earlier versions of this set, and
to Ido for providing an update to the mlxsw driver.
Changes since RFC
- cleanup wording in test script; add comments about expected failures
and why
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 route tests covering add, append and replace permutations.
Assumes the ability to add a basic single path route works; this is
required for example when adding an address to an interface.
$ fib_tests.sh -t ipv4_rt
IPv4 route add / append tests
TEST: Attempt to add duplicate route - gw [ OK ]
TEST: Attempt to add duplicate route - dev only [ OK ]
TEST: Attempt to add duplicate route - reject route [ OK ]
TEST: Add new nexthop for existing prefix [ OK ]
TEST: Append nexthop to existing route - gw [ OK ]
TEST: Append nexthop to existing route - dev only [ OK ]
TEST: Append nexthop to existing route - reject route [ OK ]
TEST: Append nexthop to existing reject route - gw [ OK ]
TEST: Append nexthop to existing reject route - dev only [ OK ]
TEST: add multipath route [ OK ]
TEST: Attempt to add duplicate multipath route [ OK ]
TEST: Route add with different metrics [ OK ]
TEST: Route delete with metric [ OK ]
IPv4 route replace tests
TEST: Single path with single path [ OK ]
TEST: Single path with multipath [ OK ]
TEST: Single path with reject route [ OK ]
TEST: Single path with single path via multipath attribute [ OK ]
TEST: Invalid nexthop [ OK ]
TEST: Single path - replace of non-existent route [ OK ]
TEST: Multipath with multipath [ OK ]
TEST: Multipath with single path [ OK ]
TEST: Multipath with single path via multipath attribute [ OK ]
TEST: Multipath with reject route [ OK ]
TEST: Multipath - invalid first nexthop [ OK ]
TEST: Multipath - invalid second nexthop [ OK ]
TEST: Multipath - replace of non-existent route [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 route tests covering add, append and replace permutations.
Assumes the ability to add a basic single path route works; this is
required for example when adding an address to an interface.
$ fib_tests.sh -t ipv6_rt
IPv6 route add / append tests
TEST: Attempt to add duplicate route - gw [ OK ]
TEST: Attempt to add duplicate route - dev only [ OK ]
TEST: Attempt to add duplicate route - reject route [ OK ]
TEST: Add new route for existing prefix (w/o NLM_F_EXCL) [ OK ]
TEST: Append nexthop to existing route - gw [ OK ]
TEST: Append nexthop to existing route - dev only [ OK ]
TEST: Append nexthop to existing route - reject route [ OK ]
TEST: Append nexthop to existing reject route - gw [ OK ]
TEST: Append nexthop to existing reject route - dev only [ OK ]
TEST: Add multipath route [ OK ]
TEST: Attempt to add duplicate multipath route [ OK ]
TEST: Route add with different metrics [ OK ]
TEST: Route delete with metric [ OK ]
IPv6 route replace tests
TEST: Single path with single path [ OK ]
TEST: Single path with multipath [ OK ]
TEST: Single path with reject route [ OK ]
TEST: Single path with single path via multipath attribute [ OK ]
TEST: Invalid nexthop [ OK ]
TEST: Single path - replace of non-existent route [ OK ]
TEST: Multipath with multipath [ OK ]
TEST: Multipath with single path [ OK ]
TEST: Multipath with single path via multipath attribute [ OK ]
TEST: Multipath with reject route [ OK ]
TEST: Multipath - invalid first nexthop [ OK ]
TEST: Multipath - invalid second nexthop [ OK ]
TEST: Multipath - replace of non-existent route [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option to pause after each test before cleanup is done. Allows
user to do manual inspection or more ad-hoc testing after each test
with the setup in tact.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add command line options for controlling pause on fail, controlling
specific tests to run and verbose mode rather than relying on environment
variables.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As more tests are added, it is convenient to have a tally at the end.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring consistency to ipv6 route replace and append semantics.
Remove rt6_qualify_for_ecmp which is just guess work. It fails in 2 cases:
1. can not replace a route with a reject route. Existing code appends
a new route instead of replacing the existing one.
2. can not have a multipath route where a leg uses a dev only nexthop
Existing use cases affected by this change:
1. adding a route with existing prefix and metric using NLM_F_CREATE
without NLM_F_APPEND or NLM_F_EXCL (ie., what iproute2 calls
'prepend'). Existing code auto-determines that the new nexthop can
be appended to an existing route to create a multipath route. This
change breaks that by requiring the APPEND flag for the new route
to be added to an existing one. Instead the prepend just adds another
route entry.
2. route replace. Existing code replaces first matching multipath route
if new route is multipath capable and fallback to first matching
non-ECMP route (reject or dev only route) in case one isn't available.
New behavior replaces first matching route. (Thanks to Ido for spotting
this one)
Note: Newer iproute2 is needed to display multipath routes with a dev-only
nexthop. This is due to a bug in iproute2 and parsing nexthops.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle append for gateway based routes. Dev-only multipath routes will
be handled by a follow on patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we no longer use i as an array index for the data variable,
replace the use of 'j' with 'i' so that we match the general loop
variable name.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add documentation for the i40e_get_stats_count, i40e_get_stat_strings
and i40e_get_ethtool_stats explaining that the number and ordering of
statistics must remain constant for a given netdevice.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch is going to add a helper function i40e_add_ethtool_stats
that will help lower the amount of boiler plate code in the
i40e_get_ethtool_stats function.
This conversion will take place over many patches, and the helper
function will work by directly updating a reference to the data pointer.
Since this would not work combined with the current method of accessing
data like an array, update all the code that copies stats into the data
buffer to use direct updates to the pointer instead of array accesses.
This will prevent incorrect stat updates for patches in between the
conversion.
Similarly, when copying strings, we used a separate char *p pointer.
Instead, use the data pointer directly as it's already a (u8 *) type
which is the same size.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We always prefix these stats with a fixed string, so just fold this
prefix into the stat string definition. This preparatory work will make
it easier to implement a helper function to copy stats and strings into
the supplied buffers in a future patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't really want to use BUG_ON here since that would completely
crash the kernel, thus the reason we commented it out. We *can't* use
BUILD_BUG_ON because at least now (a) the sizes aren't constant (we are
fixing this) and (b) not all compilers are smart enough to understand
that "p - data" is a constant.
Instead, just use a WARN_ONCE so that the first time we end up with an
incorrect size we will dump a stack trace and a message, hopefully
highlighting the issues early in testing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the statistic strings and private flags strings into their own
separate functions to aid code readability.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API for obtaining device statistics is not intended to allow
runtime changes in the number of statistics reported. It may *appear*
this way, as there is an ability to request the number of stats using
ethtool_get_set_count(). However, it is expected that this must always
return the same value for invocations of the same device.
If we don't satisfy this contract, and allow the number of stats to
change during run time, we could cause invalid memory accesses or report
the stat strings incorrectly. This is because the API for obtaining
stats is to (1) get the size, (2) get the strings and finally (3) get
the stats. Since these are each separate ethtool op commands, it is not
possible to maintain consistency by holding the RTNL lock over the whole
operation. This results in the potential for a race condition to occur
where the size changed between any of the 3 calls.
Avoid this issue by requiring that we always return the same value for
a given device. We can check any values which remain constant for the
life of the device, but must not report different sizes depending on
runtime attributes.
This patch specifically fixes the queue statistics to always return
every queue even if it's not currently in use.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API for obtaining device statistics is not intended to allow
runtime changes in the number of statistics reported. It may *appear*
this way, as there is an ability to request the number of stats using
ethtool_get_set_count(). However, it is expected that this must always
return the same value for invocations of the same device.
If we don't satisfy this contract, and allow the number of stats to
change during run time, we could cause invalid memory accesses or report
the stat strings incorrectly. This is because the API for obtaining
stats is to (1) get the size, (2) get the strings and finally (3) get
the stats. Since these are each separate ethtool op commands, it is not
possible to maintain consistency by holding the RTNL lock over the whole
operation. This results in the potential for a race condition to occur
where the size changed between any of the 3 calls.
Avoid this issue by requiring that we always return the same value for
a given device. We can check any values which remain constant for the
life of the device, but must not report different sizes depending on
runtime attributes.
This patch specifically fixes the VEB statistics strings to always be
reported. Other issues will be fixed in future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the same logic to free the skb after clearing the Tx timestamp bit
lock in i40e_ptp_stop as we use in the other locations. It is not as
important here since we are not racing against a future Tx timestamp
request (as we are disabling PTP at this point). However it is good to
be consistent in how we approach the bit lock so that future callers
don't copy the old anti-pattern.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Florian Fainelli says:
====================
TI Ethernet driver warnings fixes
This patch series attempts to fix properly the warnings observed with turning
on COMPILE_TEST and TI Ethernet drivers on 64-bit hosts.
Since I don't have any of this hardware, please review carefully for possible
breakage!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can compile test this driver on 64-bit hosts, we get some
warnings about how a pointer/address is written/read to/from a register
(sw_token). Fix this by doing the appropriate conversions, we cannot
possibly have the driver work on 64-bit hosts the way the tokens are
managed though, since the registers being written to a 32-bit only.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %pa which is the correct formatter to print a physical address,
instead of %p which is just a pointer.
Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building on a 64-bit host we will get the following warning:
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_add_ch_strings':
drivers/net/ethernet/ti/cpsw.c:1284:19: warning: format '%d' expects
argument of type 'int', but argument 5 has type 'long unsigned int'
[-Wformat=]
"%s DMA chan %d: %s", rx_dir ? "Rx" : "Tx",
~^
%ld
Fix this by using an %ld format and casting to long.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64-bit hosts we will get the following warning:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_overflow_check':
drivers/net/ethernet/ti/cpts.c:297:11: warning: format '%lld' expects
argument of type 'long long int', but argument 3 has type
'__kernel_time_t {aka long int}' [-Wformat=]
pr_debug("cpts overflow check at %lld.%09lu\n", ts.tv_sec,
ts.tv_nsec);
Fix this by using an appropriate casting that works on all bit sizes.
Fixes: a5c79c26e1 ("ptp: cpts: convert to the 64 bit get/set time methods.")
Fixes: 87c0e764d4 ("cpts: introduce time stamping code and a PTP hardware clock.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can compile davinci_cpdma.c on 64-bit hosts, we can see that
the format used for printing a size_t type is incorrect, use %zd
accordingly.
Fixes: aeec302104 ("net: ethernet: ti: cpdma: remove used_desc counter")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix below build warning:
WARNING: vmlinux.o(.text+0x422bb8): Section mismatch in reference from
the function vmcore_add_device_dump() to the function
.init.text:get_vmcore_size.constprop.5()
The function vmcore_add_device_dump() references
the function __init get_vmcore_size.constprop.5().
This is often because vmcore_add_device_dump lacks a __init
annotation or the annotation of get_vmcore_size.constprop.5 is wrong.
Fixes: 7efe48df8a ("vmcore: append device dumps to vmcore as elf notes")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
immdlen field of FW_ETH_TX_PKT_WR is filled in a wrong way,
we must copy the length of all the cpls encapsulated in fw
work request. In the xmit path we missed adding the length
of CPL_TX_PKT_CORE but we added the length of WR_HDR and it
worked because WR_HDR and CPL_TX_PKT_CORE are of same length.
Add the length of cpl_tx_pkt_core not WR_HDR's. This also
fixes the lso cpl errors for udp tunnels
Fixes: d0a1299c6b ("cxgb4: add support for vxlan segmentation offload")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of entries were not alphabetically sorted, remedy that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_GPIOLIB is disabled, gpiod_put() becomes a stub that produces a
warning, this helped identify that we could be attempting to release a NULL
pl->link_gpio GPIO descriptor, so guard against that.
Fixes: daab3349ad ("net: phy: phylink: Release link GPIO")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MIPS fixes for 4.17:
- Fix build with DEBUG_ZBOOT and MACH_JZ4770 (4.16)
- Include xilfpga FDT in fitImage and stop generating dtb.o (4.15)
- Fix software IO coherence on CM SMP systems (4.8)
- ptrace: Fix PEEKUSR/POKEUSR to o32 FGRs (3.14)
- ptrace: Expose FIR register through FP regset (3.13)
- Fix typo in KVM debugfs file name (3.10)
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS7lRNBWUYtqfDOVL41zuSGKxAj8gUCWwK2jAAKCRA1zuSGKxAj
8kXbAQD/Poo0YeGR+yWZKrJauEAkvW1Z2YwM7sb0xEQJiOLr+QEAo4nAl0HCIZoB
Xzk0sWgRvr1aBAILjJkbZyGUFHHbHwc=
=h7B4
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_4.17_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS fixes from James Hogan:
- fix build with DEBUG_ZBOOT and MACH_JZ4770 (4.16)
- include xilfpga FDT in fitImage and stop generating dtb.o (4.15)
- fix software IO coherence on CM SMP systems (4.8)
- ptrace: Fix PEEKUSR/POKEUSR to o32 FGRs (3.14)
- ptrace: Expose FIR register through FP regset (3.13)
- fix typo in KVM debugfs file name (3.10)
* tag 'mips_fixes_4.17_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: Fix ptrace(2) PTRACE_PEEKUSR and PTRACE_POKEUSR accesses to o32 FGRs
MIPS: xilfpga: Actually include FDT in fitImage
MIPS: xilfpga: Stop generating useless dtb.o
KVM: Fix spelling mistake: "cop_unsuable" -> "cop_unusable"
MIPS: ptrace: Expose FIR register through FP regset
MIPS: Fix build with DEBUG_ZBOOT and MACH_JZ4770
MIPS: c-r4k: Fix data corruption related to cache coherence
Pull networking fixes from David Miller:
1) Fix refcounting bug for connections in on-packet scheduling mode of
IPVS, from Julian Anastasov.
2) Set network header properly in AF_PACKET's packet_snd, from Willem
de Bruijn.
3) Fix regressions in 3c59x by converting to generic DMA API. It was
relying upon the hack that the PCI DMA interfaces would accept NULL
for EISA devices. From Christoph Hellwig.
4) Remove RDMA devices before unregistering netdev in QEDE driver, from
Michal Kalderon.
5) Use after free in TUN driver ptr_ring usage, from Jason Wang.
6) Properly check for missing netlink attributes in SMC_PNETID
requests, from Eric Biggers.
7) Set DMA mask before performaing any DMA operations in vmxnet3
driver, from Regis Duchesne.
8) Fix mlx5 build with SMP=n, from Saeed Mahameed.
9) Classifier fixes in bcm_sf2 driver from Florian Fainelli.
10) Tuntap use after free during release, from Jason Wang.
11) Don't use stack memory in scatterlists in tls code, from Matt
Mullins.
12) Not fully initialized flow key object in ipv4 routing code, from
David Ahern.
13) Various packet headroom bug fixes in ip6_gre driver, from Petr
Machata.
14) Remove queues from XPS maps using correct index, from Amritha
Nambiar.
15) Fix use after free in sock_diag, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (64 commits)
net: ip6_gre: fix tunnel metadata device sharing.
cxgb4: fix offset in collecting TX rate limit info
net: sched: red: avoid hashing NULL child
sock_diag: fix use-after-free read in __sk_free
sh_eth: Change platform check to CONFIG_ARCH_RENESAS
net: dsa: Do not register devlink for unused ports
net: Fix a bug in removing queues from XPS map
bpf: fix truncated jump targets on heavy expansions
bpf: parse and verdict prog attach may race with bpf map update
bpf: sockmap update rollback on error can incorrectly dec prog refcnt
net: test tailroom before appending to linear skb
net: ip6_gre: Fix ip6erspan hlen calculation
net: ip6_gre: Split up ip6gre_changelink()
net: ip6_gre: Split up ip6gre_newlink()
net: ip6_gre: Split up ip6gre_tnl_change()
net: ip6_gre: Split up ip6gre_tnl_link_config()
net: ip6_gre: Fix headroom request in ip6erspan_tunnel_xmit()
net: ip6_gre: Request headroom in __gre6_xmit()
selftests/bpf: check return value of fopen in test_verifier.c
erspan: fix invalid erspan version.
...
In mv88e6xxx_probe(), ("np" or "pdata") might be an invariant
but GCC can't see that, therefore:
drivers/net/dsa/mv88e6xxx/chip.c: In function ‘mv88e6xxx_probe’:
drivers/net/dsa/mv88e6xxx/chip.c:4420:13: warning: ‘compat_info’ may be used uninitialized in this function [-Wmaybe-uninitialized]
chip->info = compat_info;
Actually, it should have warned on the "if (!compat_info)" test, but
whatever.
Explicitly initialize to NULL in the variable declaration to
deal with this.
Fixes: 877b7cb0b6 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53 driver already defines and internally uses platform data to let the
glue drivers specify parameters such as the chip id. What we were missing was
a way to tell the core DSA layer about the ports and their type.
Place a dsa_chip_data structure at the beginning of b53_platform_data for
dsa_register_switch() to access it. This does not require modifications to
b53_common.c which will pass platform_data trough.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
Platform data support for mv88exxx
There are a few Intel based platforms making use of the mv88exxx.
These don't easily have access to device tree in order to instantiate
the switch driver. These patches allow the use of platform data to
hold the configuration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the size of the EEPROM to the platform data, so it can also be
instantiated by a platform device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all the world uses device tree. Some parts of the world still use
platform devices and platform data. Add basic support for probing a
Marvell switch via platform data.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IRQ domain will work without an OF node. It is not possible to
reference interrupts via a phandle, but C code can still use
irq_find_mapping() to get an interrupt from the domain.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov says:
====================
sh_eth: fix typos/grammar
Here's a set of 3 patches against DaveM's 'net-next.git' repo plus the R8A77980
support patches posted earlier. They fix the comments typos/grammar and another
typo in the EESR bit...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon has noticed a typo in the comment accompaining the BCULR write --
fix it and move the comment before the write (following the style of
the other comments), while at it...
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the verbs in the comments to the 'struct sh_eth_cpu_data' declaration
should be in a 3rd person singular, to match the nouns.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the EESR bit 8 is TRO (transmit retry over), not RTO.
Note that EESIPR bit 8, TROIP remained correct...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta says:
====================
Misc. bug fixes and cleanup for HNS3 driver
This patch-set presents miscellaneous bug fixes and cleanups found
during internal review, system testing and cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru