This was noticed when printing debugfs for MSIs on my ARM64 server. The
new dstate IRQD_MSI_NOMASK_QUIRK came out surprisingly while it should only
be the x86 stuff for the time being...
The new MSI quirk flag uses the same bit as IRQ_DOMAIN_NAME_ALLOCATED which
is oddly defined as bit 6 for no good reason.
Switch it to the non used bit 1.
Fixes: 6f1a4891a5 ("x86/apic/msi: Plug non-maskable MSI affinity race")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200221020725.2038-1-yuzenghui@huawei.com
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when the
TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused an
infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects PCI
devices with non-maskable MSI interrupts. The problem is caused by the
non-atomic writes of the MSI address (destination APIC id) and data
(vector) fields which the device uses to construct the MSI message. The
non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after writing
address and before writing data, then the MSI block constructs a
inconsistent message which causes interrupts to be lost and subsequent
malfunction of the device.
The fix is to redirect the interrupt to the new vector on the current
CPU first and then switch it over to the new target CPU. This allows to
observe an eventually raised interrupt in the transitional stage (old
CPU, new vector) to be observed in the APIC IRR and retriggered on the
new target CPU and the new vector. The potential spurious interrupts
caused by this are harmless and can in the worst case expose a buggy
driver (all handlers have to be able to deal with spurious interrupts as
they can and do happen for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall page
which prevents resume hibernation on HYPERV guests. This change got
lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent potentially
stale IOAPIC remote IRR bits which cause stale interrupt lines after
resume.
-----BEGIN PGP SIGNATURE-----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=WxKD
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
Evan tracked down a subtle race between the update of the MSI message and
the device raising an interrupt internally on PCI devices which do not
support MSI masking. The update of the MSI message is non-atomic and
consists of either 2 or 3 sequential 32bit wide writes to the PCI config
space.
- Write address low 32bits
- Write address high 32bits (If supported by device)
- Write data
When an interrupt is migrated then both address and data might change, so
the kernel attempts to mask the MSI interrupt first. But for MSI masking is
optional, so there exist devices which do not provide it. That means that
if the device raises an interrupt internally between the writes then a MSI
message is sent built from half updated state.
On x86 this can lead to spurious interrupts on the wrong interrupt
vector when the affinity setting changes both address and data. As a
consequence the device interrupt can be lost causing the device to
become stuck or malfunctioning.
Evan tried to handle that by disabling MSI accross an MSI message
update. That's not feasible because disabling MSI has issues on its own:
If MSI is disabled the PCI device is routing an interrupt to the legacy
INTx mechanism. The INTx delivery can be disabled, but the disablement is
not working on all devices.
Some devices lose interrupts when both MSI and INTx delivery are disabled.
Another way to solve this would be to enforce the allocation of the same
vector on all CPUs in the system for this kind of screwed devices. That
could be done, but it would bring back the vector space exhaustion problems
which got solved a few years ago.
Fortunately the high address (if supported by the device) is only relevant
when X2APIC is enabled which implies interrupt remapping. In the interrupt
remapping case the affinity setting is happening at the interrupt remapping
unit and the PCI MSI message is programmed only once when the PCI device is
initialized.
That makes it possible to solve it with a two step update:
1) Target the MSI msg to the new vector on the current target CPU
2) Target the MSI msg to the new vector on the new target CPU
In both cases writing the MSI message is only changing a single 32bit word
which prevents the issue of inconsistency.
After writing the final destination it is necessary to check whether the
device issued an interrupt while the intermediate state #1 (new vector,
current CPU) was in effect.
This is possible because the affinity change is always happening on the
current target CPU. The code runs with interrupts disabled, so the
interrupt can be detected by checking the IRR of the local APIC. If the
vector is pending in the IRR then the interrupt is retriggered on the new
target CPU by sending an IPI for the associated vector on the target CPU.
This can cause spurious interrupts on both the local and the new target
CPU.
1) If the new vector is not in use on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then interrupt entry code will
ignore that spurious interrupt. The vector is marked so that the
'No irq handler for vector' warning is supressed once.
2) If the new vector is in use already on the local CPU then the IRR check
might see an pending interrupt from the device which is using this
vector. The IPI to the new target CPU will then invoke the handler of
the device, which got the affinity change, even if that device did not
issue an interrupt
3) If the new vector is in use already on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then the handler of the device which
uses that vector on the local CPU will be invoked.
expose issues in device driver interrupt handlers which are not prepared to
handle a spurious interrupt correctly. This not a regression, it's just
exposing something which was already broken as spurious interrupts can
happen for a lot of reasons and all driver handlers need to be able to deal
with them.
Reported-by: Evan Green <evgreen@chromium.org>
Debugged-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87imkr4s7n.fsf@nanos.tec.linutronix.de
A single controller can handle normal interrupts and wake-up interrupts
independently, with a different numbering space. It is thus crucial to
allow the driver for such a controller discriminate between the two.
A simple way to do so is to tag the wake-up irqdomain with a "bus token"
that indicates the wake-up domain. This slightly abuses the notion of
bus, but also radically simplifies the design of such a driver. Between
two evils, we choose the least damaging.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-2-git-send-email-ilina@codeaurora.org
Booting a large arm64 server (HiSi D05) leads to the following
shouting at boot time:
[ 20.722132] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.730851] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.739560] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.748267] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.756975] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.765683] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.774391] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
and many more... Evidently, we expect something a bit more informative
than ____ptrval____, and certainly we want all of our domains, not just
the first one.
For that, turn the %p used to generate the fwnode name into something
that won't be repainted (%pa). Given that we've now fixed all users to
pass a pointer to a PA, it will actually do the right thing.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
With the system coprocessor managing the range allocation of the
inputs to Interrupt Aggregator, it is difficult to represent
the device IRQs from DT.
The suggestion is to use MSI in such cases where devices wants
to allocate and group interrupts dynamically.
Create a MSI domain bus layer that allocates and frees MSIs for
a device.
APIs that are implemented:
- ti_sci_inta_msi_create_irq_domain() that creates a MSI domain
- ti_sci_inta_msi_domain_alloc_irqs() that creates MSIs for the
specified device and resource.
- ti_sci_inta_msi_domain_free_irqs() frees the irqs attached to the device.
- ti_sci_inta_msi_get_virq() for getting the virq attached to a specific event.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Core changes:
- The big change this time around is the irqchip handling in
the qualcomm pin controllers, closely coupled with the
gpiochip. This rework, in a classic fall-between-the-chairs
fashion has been sidestepped for too long. The Qualcomm
IRQchips using the SPMI and SSBI transport mechanisms have
been rewritten to use hierarchical irqchip. This creates
the base from which I intend to gradually pull support for
hierarchical irqchips into the gpiolib irqchip helpers to
cut down on duplicate code. We have too many hacks in the
kernel because people have been working around the missing
hierarchical irqchip for years, and once it was there,
noone understood it for a while. We are now slowly adapting
to using it. This is why this pull requests include changes
to MFD, SPMI, IRQchip core and some ARM Device Trees
pertaining to the Qualcomm chip family. Since Qualcomm have
so many chips and such large deployments it is paramount
that this platform gets this right, and now it (hopefully)
does.
- Core support for pull-up and pull-down configuration, also
from the device tree. When a simple GPIO chip support a
"off or on" pull-up or pull-down resistor, we provide a
way to set this up using machine descriptors or device tree.
If more elaborate control of pull up/down (such as
resistance shunt setting) is required, drivers should be
phased over to use pin control. We do not yet provide a
userspace ABI for this pull up-down setting but I suspect
the makers are going to ask for it soon enough. PCA953x
is the first user of this new API.
- The GPIO mockup driver has been revamped after some
discussion improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for
both testing and virtual prototyping, e.g. when you do
not yet have a GPIO expander to play with but really
want to get something to develop code around before
hardware is available. It's neat. The blackbox testing
usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating
flags.
- A new device core helper for devm_platform_ioremap_resource()
is funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped
I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum
driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers.
-----BEGIN PGP SIGNATURE-----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=VoVC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
The default irq domain allows legacy code to create irqdomain
mappings without having to track the domain it is allocating
from. Setting the default domain is a one shot, fire and forget
operation, and no effort was made to be able to retrieve this
information at a later point in time.
Newer irqdomain APIs (the hierarchical stuff) relies on both
the irqchip code to track the irqdomain it is allocating from,
as well as some form of firmware abstraction to easily identify
which piece of HW maps to which irq domain (DT, ACPI).
For systems without such firmware (or legacy platform that are
getting dragged into the 21st century), things are a bit harder.
For these cases (and these cases only!), let's provide a way
to retrieve the default domain, allowing the use of the v2 API
without having to resort to platform-specific hacks.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a new function irq_domain_translate_twocell() that is to be used as
the translate function in struct irq_domain_ops for the v2 IRQ API.
This patch also changes irq_domain_xlate_twocell() from the v1 IRQ API
to call irq_domain_translate_twocell() in the v2 IRQ API. This required
changes to of_phandle_args_to_fwspec()'s arguments so that it can be
called from multiple places.
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt affinity management uses straight cpumask pointers to convey
the automatically assigned affinity masks for managed interrupts. The core
interrupt descriptor allocation also decides based on the pointer being non
NULL whether an interrupt is managed or not.
Devices which use managed interrupts usually have two classes of
interrupts:
- Interrupts for multiple device queues
- Interrupts for general device management
Currently both classes are treated the same way, i.e. as managed
interrupts. The general interrupts get the default affinity mask assigned
while the device queue interrupts are spread out over the possible CPUs.
Treating the general interrupts as managed is both a limitation and under
certain circumstances a bug. Assume the following situation:
default_irq_affinity = 4..7
So if CPUs 4-7 are offlined, then the core code will shut down the device
management interrupts because the last CPU in their affinity mask went
offline.
It's also a limitation because it's desired to allow manual placement of
the general device interrupts for various reasons. If they are marked
managed then the interrupt affinity setting from both user and kernel space
is disabled.
To remedy that situation it's required to convey more information than the
cpumasks through various interfaces related to interrupt descriptor
allocation.
Instead of adding yet another argument, create a new data structure
'irq_affinity_desc' which for now just contains the cpumask. This struct
can be expanded to convey auxilliary information in the next step.
No functional change, just preparatory work.
[ tglx: Simplified logic and clarified changelog ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dou Liyang <douliyangs@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: kashyap.desai@broadcom.com
Cc: shivasharan.srikanteshwara@broadcom.com
Cc: sumit.saxena@broadcom.com
Cc: ming.lei@redhat.com
Cc: hch@lst.de
Cc: douliyang1@huawei.com
Link: https://lkml.kernel.org/r/20181204155122.6327-2-douliyangs@gmail.com
This is a cascaded interrupt controller in the AP806 GIC that collapses
SEIs (System Error Interrupt) coming from the AP and the CPs (through
the ICU).
The SEI handles up to 64 interrupts. The first 21 interrupts are wired
from the AP. The next 43 interrupts are from the CPs and are triggered
through MSI messages. To handle this complexity, the driver has to
declare to the upper layer: one IRQ domain for the wired interrupts,
one IRQ domain for the MSIs; and acts as a MSI controller ('parent')
by declaring an MSI domain.
Suggested-by: Haim Boot <hayim@marvell.com>
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
At the beginning of times, irq_find_host() was simple. Each device node
implemented at most one irq domain, and we were happy. Over time, things
have become more complex, and we now have nodes implementing a plurality
of domains, tagged by "bus_token".
Crutially, users of irq_find_host() all expect the most basic domain
to be returned, and not any other domain such as a bus-specific MSI
domain.
So let's change irq_find_host() to first look for a DOMAIN_BUS_WIRED
domain, and only if this fails fallback to DOMAIN_BUS_ANY. Note that
this is consistent with what irq_create_fwspec_mapping is already
doing, see 530cbe100e ("irqdomain: Allow domain lookup with
DOMAIN_BUS_WIRED token").
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-6-marc.zyngier@arm.com
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.
No functional change.
Fixes: 7249164346 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
Commit:
f110711a60 ("irqdomain: Convert irqdomain-%3Eof_node to fwnode")
converted of_node field to fwnode, but didn't update its comments.
Update it.
Fixes: f110711a60 ("irqdomain: Convert irqdomain-%3Eof_node to fwnode")
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The revmap_trees_mutex protects domain->revmap_tree. There is no
need to make it global because it is allowed to modify revmap_tree
of two different domains concurrently. Having said that, this would
not be a actual bottleneck because the interrupt map/unmap does not
occur quite often. Rather, the motivation is to tidy up the code
from a data structure point of view.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Propagate the early activation mode to the irqdomain activate()
callbacks. This is required for the upcoming reservation, late vector
assignment scheme, so that the early activation call can act accordingly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.028353660@linutronix.de
Allow irq_domain_activate_irq() to fail. This is required to support a
reservation and late vector assignment scheme.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.933882227@linutronix.de
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
In the !IRQ_DOMAIN_HIERARCHY cas the activation stubs are not
setting/clearing the activation status bits. This is not a problem at the
moment, but upcoming changes require a correct status.
Add the set/clear incovations to the stub functions and move them to the
core internal header to avoid duplication and visibility outside the core.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.591985591@linutronix.de
Some interrupt domains like the X86 vector domain has special requirements
for debugging, like showing the vector usage on the CPUs.
Add a callback to the irqdomain ops which can be filled in by domains which
require it and add conditional invocations to the irqdomain and the per irq
debug files.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.512937505@linutronix.de
- Introduce fwnode operations for all of the separate types of
"firmware nodes" that can be handled by the device properties
framework and drop the type field from struct fwnode_handle
(Sakari Ailus, Arnd Bergmann).
- Make the device properties framework use const fwnode arguments
where possible (Sakari Ailus).
- Add a helper for the consolidated handling of node references
to the device properties framework (Sakari Ailus).
- Switch over the ACPI part of the device properties framework
to the new UUID API (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0rnk
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These introduce fwnode operations for all of the separate types of
'firmware nodes' that can be handled by the device properties
framework, make the framework use const fwnode arguments all over, add
a helper for the consolidated handling of node references and switch
over the framework to the new UUID API.
Specifics:
- Introduce fwnode operations for all of the separate types of
'firmware nodes' that can be handled by the device properties
framework and drop the type field from struct fwnode_handle (Sakari
Ailus, Arnd Bergmann).
- Make the device properties framework use const fwnode arguments
where possible (Sakari Ailus).
- Add a helper for the consolidated handling of node references to
the device properties framework (Sakari Ailus).
- Switch over the ACPI part of the device properties framework to the
new UUID API (Andy Shevchenko)"
* tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: device property: Switch to use new generic UUID API
device property: export irqchip_fwnode_ops
device property: Introduce fwnode_property_get_reference_args
device property: Constify fwnode property API
device property: Constify argument to pset fwnode backend
ACPI: Constify internal fwnode arguments
ACPI: Constify acpi_bus helper functions, switch to macros
ACPI: Prepare for constifying acpi_get_next_subnode() fwnode argument
device property: Get rid of struct fwnode_handle type field
ACPI: Use IS_ERR_OR_NULL() instead of non-NULL check in is_acpi_data_node()
For an already existing irqdomain hierarchy, as might be obtained via
a call to pci_enable_msix_range(), a PCI driver wishing to add an
additional irqdomain to the hierarchy needs to be able to insert the
irqdomain to that already initialized hierarchy. Calling
irq_domain_create_hierarchy() allows the new irqdomain to be created,
but no existing code allows for initializing the associated irq_data.
Add a couple of helper functions (irq_domain_push_irq() and
irq_domain_pop_irq()) to initialize the irq_data for the new
irqdomain added to an existing hierarchy.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Link: http://lkml.kernel.org/r/1503017616-3252-6-git-send-email-david.daney@cavium.com
Instead of relying on the struct fwnode_handle type field, define
fwnode_operations structs for all separate types of fwnodes. To find out
the type, compare to the ops field to relevant ops structs.
This change has two benefits:
1. it avoids adding the type field to each and every instance of struct
fwnode_handle, thus saving memory and
2. makes the ops field the single factor that defines both the types of
the fwnode as well as defines the implementation of its operations,
decreasing the possibility of bugs when developing code dealing with
fwnode internals.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It did seem like a good idea at the time, but it never really
caught on, and auto-recursive domains remain unused 3 years after
having been introduced.
Oh well, time for a late spring cleanup.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We can have irq domains that are identified by the same fwnode
(because they are serviced by the same HW), and yet have different
functionnality (because they serve different busses, for example).
This is what we use the bus_token field.
Since we don't use this field when generating the domain name,
all the aliasing domains will get the same name, and the debugfs
file creation fails. Also, bus_token is updated by individual drivers,
and the core code is unaware of that update.
In order to sort this mess, let's introduce a helper that takes care
of updating bus_token, and regenerate the debugfs file.
A separate patch will update all the individual users.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Debugging (hierarchical) interupt domains is tedious as there is no
information about the hierarchy and no information about states of
interrupts in the various domain levels.
Add a debugfs directory 'irq' and subdirectories 'domains' and 'irqs'.
The domains directory contains the domain files. The content is information
about the domain. If the domain is part of a hierarchy then the parent
domains are printed as well.
# ls /sys/kernel/debug/irq/domains/
default INTEL-IR-2 INTEL-IR-MSI-2 IO-APIC-IR-2 PCI-MSI
DMAR-MSI INTEL-IR-3 INTEL-IR-MSI-3 IO-APIC-IR-3 unknown-1
INTEL-IR-0 INTEL-IR-MSI-0 IO-APIC-IR-0 IO-APIC-IR-4 VECTOR
INTEL-IR-1 INTEL-IR-MSI-1 IO-APIC-IR-1 PCI-HT
# cat /sys/kernel/debug/irq/domains/VECTOR
name: VECTOR
size: 0
mapped: 216
flags: 0x00000041
# cat /sys/kernel/debug/irq/domains/IO-APIC-IR-0
name: IO-APIC-IR-0
size: 24
mapped: 19
flags: 0x00000041
parent: INTEL-IR-3
name: INTEL-IR-3
size: 65536
mapped: 167
flags: 0x00000041
parent: VECTOR
name: VECTOR
size: 0
mapped: 216
flags: 0x00000041
Unfortunately there is no per cpu information about the VECTOR domain (yet).
The irqs directory contains detailed information about mapped interrupts.
# cat /sys/kernel/debug/irq/irqs/3
handler: handle_edge_irq
status: 0x00004000
istate: 0x00000000
ddepth: 1
wdepth: 0
dstate: 0x01018000
IRQD_IRQ_DISABLED
IRQD_SINGLE_TARGET
IRQD_MOVE_PCNTXT
node: 0
affinity: 0-143
effectiv: 0
pending:
domain: IO-APIC-IR-0
hwirq: 0x3
chip: IR-IO-APIC
flags: 0x10
IRQCHIP_SKIP_SET_WAKE
parent:
domain: INTEL-IR-3
hwirq: 0x20000
chip: INTEL-IR
flags: 0x0
parent:
domain: VECTOR
hwirq: 0x3
chip: APIC
flags: 0x0
This was developed to simplify the debugging of the managed affinity
changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.537566163@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a map counter instead of counting radix tree entries for
diagnosis. That also gives correct information for linear domains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.459397746@linutronix.de
In order to provide proper debug interface it's required to have domain
names available when the domain is added. Non fwnode based architectures
like x86 have no way to do so.
It's not possible to use domain ops or host data for this as domain ops
might be the same for several instances, but the names have to be unique.
Extend the irqchip fwnode to allow transporting the domain name. If no node
is supplied, create a 'unknown-N' placeholder.
Warn if an invalid node is supplied and treat it like no node. This happens
e.g. with i2 devices on x86 which hand in an ACPI type node which has no
interface for retrieving the name.
[ Folded a fix from Marc to make DT name parsing work ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.588784933@linutronix.de
Fix following build error for s390:
drivers/vfio/vfio_iommu_type1.c: In function 'vfio_iommu_type1_attach_group':
drivers/vfio/vfio_iommu_type1.c:1290:25: error: implicit declaration of function 'irq_domain_check_msi_remap'
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This new function checks whether all MSI irq domains
implement IRQ remapping. This is useful to understand
whether VFIO passthrough is safe with respect to interrupts.
On ARM typically an MSI controller can sit downstream
to the IOMMU without preventing VFIO passthrough.
As such any assigned device can write into the MSI doorbell.
In case the MSI controller implements IRQ remapping, assigned
devices will not be able to trigger interrupts towards the
host. On the contrary, the assignment must be emphasized as
unsafe with respect to interrupts.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We introduce two new enum values for the irq domain flag:
- IRQ_DOMAIN_FLAG_MSI indicates the irq domain corresponds to
an MSI domain
- IRQ_DOMAIN_FLAG_MSI_REMAP indicates the irq domain has MSI
remapping capabilities.
Those values will be useful to check all MSI irq domains have
MSI remapping support when assessing the safety of IRQ assignment
to a guest.
irq_domain_hierarchical_is_msi_remap() allows to check if an
irq domain or any parent implements MSI remapping.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some IRQ chips, such as GPIO controllers or secondary level interrupt
controllers, may require require additional runtime power management
control to ensure they are accessible. For such IRQ chips, it makes sense
to enable the IRQ chip when interrupts are requested and disabled them
again once all interrupts have been freed.
When mapping an IRQ, the IRQ type settings are read and then programmed.
The mapping of the IRQ happens before the IRQ is requested and so the
programming of the type settings occurs before the IRQ is requested. This
is a problem for IRQ chips that require additional power management
control because they may not be accessible yet. Therefore, when mapping
the IRQ, don't program the type settings, just save them and then program
these saved settings when the IRQ is requested (so long as if they are not
overridden via the call to request the IRQ).
Add a stub function for irq_domain_free_irqs() to avoid any compilation
errors when CONFIG_IRQ_DOMAIN_HIERARCHY is not selected.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When iterating over the irq domain list, we try to match a domain
either by calling a match() function or by comparing a number
of fields passed as parameters.
Both approaches are a bit restrictive:
- match() is DT specific and only takes a device node
- the fallback case only deals with the fwnode_handle
It would be useful if we had a per-domain function that would
actually perform the matching check on the whole of the
irq_fwspec structure. This would allow for a domain to triage
matching attempts that need to extend beyond the fwnode.
Let's introduce irq_find_matching_fwspec(), which takes a full
blown irq_fwspec structure, and call into a select() function
implemented by the irqdomain. irq_find_matching_fwnode() is
made a wrapper around irq_find_matching_fwspec in order to
preserve compatibility.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/1460365075-7316-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make these functions return appropriate error codes when something goes
wrong.
Previously irq_destroy_ipi returned void making it impossible to notify
the caller if the request could not be fulfilled. Patch 1 in the series
added another condition in which this could fail in addition to the
existing ones. irq_reserve_ipi returned an unsigned int meaning it could
only return 0 on failure and give the caller no indication as to why the
request failed.
As time goes on there are likely to be further conditions added in which
these functions can fail. These APIs and the IPI IRQ domain are new in
4.6 and the number of existing call sites are low, changing the API now
has little impact on the code, while making it easier for these
functions to grow over time.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: ralf@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: lisa.parratt@imgtec.com
Cc: jiang.liu@linux.intel.com
Link: http://lkml.kernel.org/r/1461568464-31701-2-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Previously irq_destroy_ipi() would destroy IPIs to all CPUs that were
configured by irq_reserve_ipi(). This change makes it possible to
destroy just a subset of the IPIs. This may be useful to remove IPIs to
CPUs that have been hot removed so that the IRQ numbers allocated within
the IPI domain can be re-used.
The original behaviour is restored by passing the complete mask that the
IPI was created with.
There are currently no users of this function that would break from the
API change.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: ralf@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: lisa.parratt@imgtec.com
Cc: jiang.liu@linux.intel.com
Link: http://lkml.kernel.org/r/1461568464-31701-1-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Here is the big staging driver pull request for 4.6-rc1.
Lots of little things here, over 1600 patches or so. Notible is all of
the good Lustre work happening, those developers have finally woken up
and are cleaning up their code greatly. The Outreachy intern
application process is also happening, which brought in another 400 or
so patches. Full details are in the very long shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbrc3EACgkQMUfUDdst+ylu5ACgpdTKjrZn2vHElW3GRhTpzJdQ
wz8AoJDeur2DmBkQrKD5/u/WL4UTRNZJ
=+Q6N
-----END PGP SIGNATURE-----
Merge tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big staging driver pull request for 4.6-rc1.
Lots of little things here, over 1600 patches or so. Notable is all
of the good Lustre work happening, those developers have finally woken
up and are cleaning up their code greatly. The Outreachy intern
application process is also happening, which brought in another 400 or
so patches. Full details are in the very long shortlog.
All of these have been in linux-next with no reported issues"
* tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1673 commits)
staging: lustre: fix aligments in lnet selftest
staging: lustre: report minimum of two buffers for LNet selftest load test
staging: lustre: test for proper errno code in lstcon_rpc_trans_abort
staging: lustre: filter remaining extra spacing for lnet selftest
staging: lustre: remove extra spacing when setting variable for lnet selftest
staging: lustre: remove extra spacing of variable declartions for lnet selftest
staging: lustre: fix spacing issues checkpatch reported in lnet selftest
staging: lustre: remove returns in void function for lnet selftest
staging: lustre: fix bogus lst errors for lnet selftest
staging: netlogic: Replacing pr_err with dev_err after the call to devm_kzalloc
staging: mt29f_spinand: Replacing pr_info with dev_info after the call to devm_kzalloc
staging: android: ion: fix up file mode
staging: ion: debugfs invalid gfp mask
staging: rts5208: Replace pci_enable_device with pcim_enable_device
Staging: ieee80211: Place constant on right side of the test.
staging: speakup: Replace del_timer with del_timer_sync
staging: lowmemorykiller: fix 2 checks that checkpatch complained
staging: mt29f_spinand: Drop void pointer cast
staging: rdma: hfi1: file_ops: Replace ALIGN with PAGE_ALIGN
staging: rdma: hfi1: driver: Replace IS_ALIGNED with PAGE_ALIGNED
...
Add a generic mechanism to dynamically allocate an IPI. Depending on the
underlying implementation this creates either a single Linux irq or a
consective range of Linux irqs. The Linux irq is used later to send IPIs to
other CPUs.
[ tglx: Massaged the code and removed the 'consecutive mask' restriction for
the single IRQ case ]
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-9-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We will need to use this function to implement irq_reserve_ipi() later. So
make it non static and move the prototype to irqdomain.h to allow using it
outside irqdomain.c
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-8-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We need a way to search and match IPI domains.
Using the new enum we can use irq_find_matching_host() to do that.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-3-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These flags will be used to identify an IPI domain. We have two flavours of
IPI implementations:
IRQ_DOMAIN_FLAG_IPI_PER_CPU: Each CPU has its own virq and hwirq
IRQ_DOMAIN_FLAG_IPI_SINGLE : A single virq and hwirq for all CPUs
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-2-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since an FSL-MC bus is a new bus type that is neither PCI nor
PLATFORM, we need a new domain bus token to disambiguate the
IRQ domain for FSL-MC MSIs.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's take the (outlandish) example of an interrupt controller
capable of handling both wired interrupts and PCI MSIs.
With the current code, the PCI MSI domain is going to be tagged
with DOMAIN_BUS_PCI_MSI, and the wired domain with DOMAIN_BUS_ANY.
Things get hairy when we start looking up the domain for a wired
interrupt (typically when creating it based on some firmware
information - DT or ACPI).
In irq_create_fwspec_mapping(), we perform the lookup using
DOMAIN_BUS_ANY, which is actually used as a wildcard. This gives
us one chance out of two to end up with the wrong domain, and
we try to configure a wired interrupt with the MSI domain.
Everything grinds to a halt pretty quickly.
What we really need to do is to start looking for a domain that
would uniquely identify a wired interrupt domain, and only use
DOMAIN_BUS_ANY as a fallback.
In order to solve this, let's introduce a new DOMAIN_BUS_WIRED
token, which is going to be used exactly as described above.
Of course, this depends on the irqchip to setup the domain
bus_token, and nobody had to implement this so far.
Only so far.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1453816347-32720-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since there will be several places checking if fwnode.type
is equal FWNODE_IRQCHIP, this patch adds a convenient function
for this purpose.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch introduces pci_msi_register_fwnode_provider() for irqchip
to register a callback, to provide a way to determine appropriate MSI
domain for a pci device.
It also introduces pci_host_bridge_acpi_msi_domain(), which returns
the MSI domain of the specified PCI host bridge with DOMAIN_BUS_PCI_MSI
bus token. Then, it is assigned to pci device.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Zenghui Yu