Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
meanwhile, sorry about that.
Highlights:
1) Fix fd leak in various bpf selftests, from Brian Vazquez.
2) Fix crash in xsk when device doesn't support some methods, from
Magnus Karlsson.
3) Fix various leaks and use-after-free in rxrpc, from David Howells.
4) Fix several SKB leaks due to confusion of who owns an SKB and who
should release it in the llc code. From Eric Biggers.
5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.
6) Jumbo packets don't work after resume on r8169, as the BIOS resets
the chip into non-jumbo mode during suspend. From Heiner Kallweit.
7) Corrupt L2 header during MPLS push, from Davide Caratti.
8) Prevent possible infinite loop in tc_ctl_action, from Eric
Dumazet.
9) Get register bits right in bcmgenet driver, based upon chip
version. From Florian Fainelli.
10) Fix mutex problems in microchip DSA driver, from Marek Vasut.
11) Cure race between route lookup and invalidation in ipv4, from Wei
Wang.
12) Fix performance regression due to false sharing in 'net'
structure, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
net: reorder 'struct net' fields to avoid false sharing
net: dsa: fix switch tree list
net: ethernet: dwmac-sun8i: show message only when switching to promisc
net: aquantia: add an error handling in aq_nic_set_multicast_list
net: netem: correct the parent's backlog when corrupted packet was dropped
net: netem: fix error path for corrupted GSO frames
macb: propagate errors when getting optional clocks
xen/netback: fix error path of xenvif_connect_data()
net: hns3: fix mis-counting IRQ vector numbers issue
net: usb: lan78xx: Connect PHY before registering MAC
vsock/virtio: discard packets if credit is not respected
vsock/virtio: send a credit update when buffer size is changed
mlxsw: spectrum_trap: Push Ethernet header before reporting trap
net: ensure correct skb->tstamp in various fragmenters
net: bcmgenet: reset 40nm EPHY on energy detect
net: bcmgenet: soft reset 40nm EPHYs before MAC init
net: phy: bcm7xxx: define soft_reset for 40nm EPHY
net: bcmgenet: don't set phydev->link from MAC
net: Update address for MediaTek ethernet driver in MAINTAINERS
ipv4: fix race condition between route lookup and invalidation
...
Printing the info message every time more than the max number of mac
addresses are requested generates unnecessary log spam. Showing it only
when the hw is not already in promiscous mode is equally informative
without being annoying.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add an error handling in aq_nic_set_multicast_list, it may not
work when hw_multicast_list_set error; and at the same time
it will remove gcc Wunused-but-set-variable warning.
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_clk, rx_clk, and tsu_clk are optional. Currently the macb driver
marks clock as not available if it receives an error when trying to get
a clock. This is wrong, because a clock controller might return
-EPROBE_DEFER if a clock is not available, but will eventually become
available.
In these cases, the driver would probe successfully but will never be
able to adjust the clocks, because the clocks were not available during
probe, but became available later.
For example, the clock controller for the ZynqMP is implemented in the
PMU firmware and the clocks are only available after the firmware driver
has been probed.
Use devm_clk_get_optional() in instead of devm_clk_get() to get the
optional clock and propagate all errors to the calling function.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).
This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.
This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink maintains packets and bytes statistics for each trap. Since
eth_type_trans() was called to set the skb's protocol, the data pointer
no longer points to the start of the packet and the bytes accounting is
off by 14 bytes.
Fix this by pushing the skb's data pointer to the start of the packet.
Fixes: b5ce611fd9 ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EPHY integrated into the 40nm Set-Top Box devices can falsely
detect energy when connected to a disabled peer interface. When the
peer interface is enabled the EPHY will detect and report the link
as active, but on occasion may get into a state where it is not
able to exchange data with the connected GENET MAC. This issue has
not been observed when the link parameters are auto-negotiated;
however, it has been observed with a manually configured link.
It has been empirically determined that issuing a soft reset to the
EPHY when energy is detected prevents it from getting into this bad
state.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that the "Workaround for putting the PHY in IDDQ mode"
used by the internal EPHYs on 40nm Set-Top Box chips when powering
down puts the interface to the GENET MAC in a state that can cause
subsequent MAC resets to be incomplete.
Rather than restore the forced soft reset when powering up internal
PHYs, this commit moves the invocation of phy_init_hw earlier in
the MAC initialization sequence to just before the MAC reset in the
open and resume functions. This allows the interface to be stable
and allows the MAC resets to be successful.
The bcmgenet_mii_probe() function is split in two to accommodate
this. The new function bcmgenet_mii_connect() handles the first
half of the functionality before the MAC initialization, and the
bcmgenet_mii_config() function is extended to provide the remaining
PHY configuration following the MAC initialization.
Fixes: 484bfa1507 ("Revert "net: bcmgenet: Software reset EPHY after power on"")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When commit 28b2e0d2cd ("net: phy: remove parameter new_link from
phy_mac_interrupt()") removed the new_link parameter it set the
phydev->link state from the MAC before invoking phy_mac_interrupt().
However, once commit 88d6272aca ("net: phy: avoid unneeded MDIO
reads in genphy_read_status") was added this initialization prevents
the proper determination of the connection parameters by the function
genphy_read_status().
This commit removes that initialization to restore the proper
functionality.
Fixes: 88d6272aca ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_pcs_ctrl_ane() expects a register address as
argument 1, but for some reason the mac_device_info is
being passed.
Fix the warning (and possible bug) from sparse:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: expected void [noderef] <asn:2> *ioaddr
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: got struct mac_device_info *hw
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.
Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.
Fixes: 1fa0f68c92 ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
disable ptp_ref_clk in suspend flow, and enable it in resume flow.
Fixes: f573c0b9c4 ("stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RGMII_MODE_EN bit value was 0 for GENET versions 1 through 3, and
became 6 for GENET v4 and above, account for that difference.
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tc_flow_parsers is not used outside of the driver, so
make it static to avoid the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c:516:3: warning: symbol 'tc_flow_parsers' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpdma_chan_split_pool() function is not used outside of
the driver, so make it static to avoid the following sparse
warning:
drivers/net/ethernet/ti/davinci_cpdma.c:725:5: warning: symbol 'cpdma_chan_split_pool' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f683b9204 ("i825xx: switch to switch to dma_alloc_attrs")
switched dma allocation over to dma_alloc_attr, but didn't convert
the SNI part to request consistent DMA memory. This broke sni_82596
since driver doesn't do dma_cache_sync for performance reasons.
Fix this by using different DMA_ATTRs for lasi_82596 and sni_82596.
Fixes: 7f683b9204 ("i825xx: switch to switch to dma_alloc_attrs")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original design, mtk_phy_connect function will set ge_mode=1
if phy-mode is GMII(PHY_INTERFACE_MODE_GMII) and then set the correct
ge_mode to ETHSYS_SYSCFG0 register. This logic was broken after apply
mediatek PHYLINK patch(Fixes tag), the new mtk_mac_config function will
not set ge_mode=1 for GMII mode hence the final ETHSYS_SYSCFG0 setting
will be incorrect for mt7629 GMII mode. This patch add the missing logic
back to fix it.
Fixes: b8fc9f3082 ("net: ethernet: mediatek: Add basic PHYLINK support")
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style
in header files related to Cavium Ethernet drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_VENDOR_BROADCOM is intended to control a kconfig menu only.
It should not have anything to do with code generation.
As such, it should not select DIMLIB for all drivers under
NET_VENDOR_BROADCOM. Instead each driver that needs DIMLIB should
select it (being the symbols SYSTEMPORT, BNXT, and BCMGENET).
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907021810220.13058@ramsan.of.borg/
Fixes: 4f75da3666 ("linux/dim: Move implementation to .c files")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Tal Gilboa <talgi@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phydev->dev_flags is entirely dependent on the PHY device driver which
is going to be used, setting the internal GENET PHY revision in those
bits only makes sense when drivers/net/phy/bcm7xxx.c is the PHY driver
being used.
Fixes: 487320c541 ("net: bcmgenet: communicate integrated PHY revision to PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan and multicast handling is now mixed up.
The explicit issue is that macvlan interface gets broken (no traffic)
after clearing MULTICAST flag on the real interface.
We now do separate logic and consider both ALLMULTI and MULTICAST
flags on the device.
Fixes: 11ba961c91 ("net: aquantia: Fix IFF_ALLMULTI flag functionality")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Individual descriptors on LRO TCP session should be checked
for CRC errors. It was discovered that HW recalculates
L4 checksums on LRO session and does not break it up on bad L4
csum.
Thus, driver should aggregate HW LRO L4 statuses from all individual
buffers of LRO session and drop packet if one of the buffers has bad
L4 checksum.
Fixes: f38f1ee8ae ("net: aquantia: check rx csum for all packets in LRO session")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From HW specification to correctly reset HW caches (this is a required
workaround when stopping the device), register bit should actually
be toggled.
It was previosly always just set. Due to the way driver stops HW this
never actually caused any issues, but it still may, so cleaning this up.
Fixes: 7a1bb49461 ("net: aquantia: fix potential IOMMU fault after driver unbind")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip temperature is a two byte word, colocated internally with cable
length data. We do all readouts from HW memory by dwords, thus
we should clear extra high bytes, otherwise temperature output
gets weird as soon as we attach a cable to the NIC.
Fixes: 8f89401186 ("net: aquantia: add infrastructure to readout chip temperature")
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pSeries machines on POWER9 processors can run with the XICS (legacy)
interrupt mode or with the XIVE exploitation interrupt mode. These
interrupt contollers have different interfaces for interrupt
management : XICS uses hcalls and XIVE loads and stores on a page.
H_EOI being a XICS interface the enable_scrq_irq() routine can fail
when the machine runs in XIVE mode.
Fix that by calling the EOI handler of the interrupt chip.
Fixes: f23e0643cd ("ibmvnic: Clear pending interrupt after device reset")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
__lpc_eth_shutdown is called after __lpc_eth_reset but it is already
calling __lpc_eth_reset. Avoid resetting the IP twice.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mariusz reported that invalid packets are sent after resume from
suspend if jumbo packets are active. It turned out that his BIOS
resets chip settings to non-jumbo on resume. Most chip settings are
re-initialized on resume from suspend by calling rtl_hw_start(),
so let's add configuring jumbo to this function.
There's nothing wrong with the commit marked as fixed, it's just
the first one where the patch applies cleanly.
Fixes: 7366016d2d ("r8169: read common register for PCI commit")
Reported-by: Mariusz Bialonczyk <manio@skyboo.net>
Tested-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Accordingly to Synopsys documentation [1] and [2], when bit PPSEN0
in register MAC_PPS_CONTROL is set it selects the functionality
command in the same register, otherwise selects the functionality
control.
Command functionality is required to either enable (command 0x2)
and disable (command 0x5) the flexible PPS output, but the bit
PPSEN0 is currently set only for enabling.
Set the bit PPSEN0 to properly disable flexible PPS output.
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Fixes: 9a8a02c9d4 ("net: stmmac: Add Flexible PPS support")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The field "name" in struct ptp_clock_info has a fixed size of 16
chars and is used as zero terminated string by clock_name_show()
in drivers/ptp/ptp_sysfs.c
The current initialization value requires 17 chars to fit also the
null termination, and this causes overflow to the next bytes in
the struct when the string is read as null terminated:
hexdump -C /sys/class/ptp/ptp0/clock_name
00000000 73 74 6d 6d 61 63 5f 70 74 70 5f 63 6c 6f 63 6b |stmmac_ptp_clock|
00000010 a0 ac b9 03 0a |.....|
where the extra 4 bytes (excluding the newline) after the string
represent the integer 0x03b9aca0 = 62500000 assigned to the field
"max_adj" that follows "name" in the same struct.
There is no strict requirement for the "name" content and in the
comment in ptp_clock_kernel.h it's reported it should just be 'A
short "friendly name" to identify the clock'.
Replace it with "stmmac ptp".
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Fixes: 92ba688851 ("stmmac: add the support for PTP hw clock driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Various minor bug fixes posted in the last couple of weeks:
- Various missed memory frees and error unwind bugs
- Fix regressions in a few iwarp drivers from 5.4 patches
- A few regressions added in past kernels
- Squash a number of races in mlx5 ODP code
-----BEGIN PGP SIGNATURE-----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=sgve
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"The usual collection of driver bug fixes, and a few regressions from
the merge window. Nothing particularly worrisome.
- Various missed memory frees and error unwind bugs
- Fix regressions in a few iwarp drivers from 5.4 patches
- A few regressions added in past kernels
- Squash a number of races in mlx5 ODP code"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Add missing synchronize_srcu() for MW cases
RDMA/mlx5: Put live in the correct place for ODP MRs
RDMA/mlx5: Order num_pending_prefetch properly with synchronize_srcu
RDMA/odp: Lift umem_mutex out of ib_umem_odp_unmap_dma_pages()
RDMA/mlx5: Fix a race with mlx5_ib_update_xlt on an implicit MR
RDMA/mlx5: Do not allow rereg of a ODP MR
IB/core: Fix wrong iterating on ports
RDMA/nldev: Reshuffle the code to avoid need to rebind QP in error path
RDMA/cxgb4: Do not dma memory off of the stack
RDMA/cm: Fix memory leak in cm_add/remove_one
RDMA/core: Fix an error handling path in 'res_get_common_doit()'
RDMA/i40iw: Associate ibdev to netdev before IB device registration
RDMA/iwcm: Fix a lock inversion issue
RDMA/iw_cxgb4: fix SRQ access from dump_qp()
RDMA/hfi1: Prevent memory leak in sdma_init
RDMA/core: Fix use after free and refcnt leak on ndev in_device in iwarp_query_port
RDMA/siw: Fix serialization issue in write_space()
RDMA/vmw_pvrdma: Free SRQ only once
Duplicate rules were not allowed to be configured with SW steering.
This restriction caused failures with the replace rule logic done by
upper layers.
This fix allows for multiple rules with the same match values, in
such case the first inserted rules will match.
Fixes: 41d0707415 ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
When the netdev is down, the queues and their debug stats
do not exist, so don't try using a pointer to them when
when printing the ethtool stats.
Fixes: e470355bd9 ("ionic: Add driver stats")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the current MAC addresses hard-coded in the test we can get some
false positives as we use the Hash Filtering method. Let's change the
MAC addresses in the tests to be unique when hashed.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some setups may not have all Unicast addresses filters available. Check
the number of available filters before trying to setup it.
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check if the number of available Hash Filters is enough to
run the test, otherwise we will get false failures.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb.
This skb should be released if pci_dma_mapping_error fails.
Fixes: 0f8ab89e82 ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fetching free MSI-X vectors for ULDs, check for the error code
before accessing MSI-X info array. Otherwise, an out-of-bounds access is
attempted, which results in kernel panic.
Fixes: 94cdb8bb99 ("cxgb4: Add support for dynamic allocation of resources for ULD")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While MR uses live as the SRCU 'update', the MW case uses the xarray
directly, xa_erase() causes the MW to become inaccessible to the pagefault
thread.
Thus whenever a MW is removed from the xarray we must synchronize_srcu()
before freeing it.
This must be done before freeing the mkey as re-use of the mkey while the
pagefault thread is using the stale mkey is undesirable.
Add the missing synchronizes to MW and DEVX indirect mkey and delete the
bogus protection against double destroy in mlx5_core_destroy_mkey()
Fixes: 534fd7aac5 ("IB/mlx5: Manage indirection mkey upon DEVX flow for ODP")
Fixes: 6aec21f6a8 ("IB/mlx5: Page faults handling infrastructure")
Link: https://lore.kernel.org/r/20191001153821.23621-7-jgg@ziepe.ca
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The stmmac driver will try to acquire its private mutex during suspend
via phylink_resolve() -> stmmac_mac_link_down() -> stmmac_eee_init().
However, the phylink configuration is updated with the private mutex
held already, which causes a deadlock during suspend.
Fix this by moving the phylink configuration updates out of the region
of code protected by the private mutex.
Fixes: 19e13cb27b ("net: stmmac: Hold rtnl lock in suspend/resume callbacks")
Suggested-by: Bitan Biswas <bbiswas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function mdio_sc_cfg_reg_write(), variable "reg_value" could be
uninitialized if regmap_read() fails. However, "reg_value" is used
to decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently added code introduces 64-bit division in dr_icm_pool_mr_create()
so that build on 32-bit architectures fails with
ERROR: "__umoddi3" [drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.ko] undefined!
As the divisor is always a power of 2, we can use bitwise operation
instead.
Fixes: 29cf8febd1 ("net/mlx5: DR, ICM pool memory allocator")
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is syncing driver with actual devicetree documentation:
Documentation/devicetree/bindings/net/qca,ar71xx.txt
|Optional subnodes:
|- mdio : specifies the mdio bus, used as a container for phy nodes
| according to phy.txt in the same directory
The driver was working with fixed phy without any noticeable issues. This bug
was uncovered by introducing dsa ar9331-switch driver.
Since no one reported this bug until now, I assume no body is using it
and this patch should not brake existing system.
Fixes: d51b6ce441 ("net: ethernet: add ag71xx driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b6b6cc9acd, changed the call to dwxgmac2_rss_write_reg()
passing it the variable cfg->key[i].
As key is an u8 but we write 32 bits at a time we need to cast it into
an u32 so that the correct key values are written. Notice that the for
loop already takes this into account so we don't try to write past the
keys size.
Fixes: b6b6cc9acd ("net: stmmac: selftest: avoid large stack usage")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sizeof(cfg->key) is != ARRAY_SIZE(cfg->key). Fix it. This warning is
triggered when running with cc flag -Wsizeof-array-div.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Fixes: 76067459c6 ("net: stmmac: Implement RSS and enable it in XGMAC core")
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use it anyway as XGMAC only supports polling for timestamp (in
current SW implementation). This greatly reduces the system load by
reducing the number of interrupts.
Fixes: 2142754f8b ("net: stmmac: Add MAC related callbacks for XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If WoL is enabled we can't really stop the PHY, otherwise we will not
receive the WoL packet. Fix this by telling phylink that only the MAC is
down and only stop the PHY if WoL is not enabled.
Fixes: 74371272f9 ("net: stmmac: Convert to phylink and remove phylib logic")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The case for PTPV2_EVENT requires event packets to be captured so add
this setting to the list of enabled captures.
Fixes: 891434b18e ("stmmac: add IEEE PTPv1 and PTPv2 support.")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to always update the MAC Hash Filter so that previous entries
are invalidated.
Found out while running stmmac selftests.
Fixes: b8ef7020d6 ("net: stmmac: add support for hash table size 128/256 in dwmac4")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although some XGMAC setups support frames larger than DMA size, some of
them may not. As we can't know before-hand which ones support let's use
the maximum DMA buffer size in the Jumbo Tests.
User can always reconfigure the MTU to achieve larger frames.
Fixes: 427849e8c3 ("net: stmmac: selftests: Add Jumbo Frame tests")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds