RSS context allocation and RSS indirection table setup are very different
on the new chip. Refactor bnxt_setup_vnic() to call 2 different functions
to set up RSS for the vnic based on chip type. On the new chip, the
number of RSS contexts and the indirection table size depends on the
number of RX rings. Each indirection table entry is also different
on the new chip since ring groups are no longer used.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the new 57500 chips, we need to allocate one RSS context for every
64 RX rings. In previous chips, only one RSS context per vnic is
required regardless of the number of RX rings. So increase the max
RSS context array count to 8.
Hardware ring groups are not used on the new chips. Note that the
software ring group structure is still maintained in the driver to
keep track of the rings associated with the vnic.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the new 57500 chips, we allocate/free one CP ring for each RX ring or
TX ring separately. Using separate CP rings for RX/TX is an improvement
as TX events will no longer be stuck behind RX events.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware ring allocation semantics are slightly different for most
ring types on 57500 chips. Allocation/deallocation for NQ rings are
also added for the new chips.
A CP ring handle is also added so that from the NQ interrupt event,
we can locate the CP ring.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the new 57500 chips, getting the associated CP ring ID associated with
an RX ring or TX ring is different than before. On the legacy chips,
we find the associated ring group and look up the CP ring ID. On the
57500 chips, each RX ring and TX ring has a dedicated CP ring even if
they share the MSIX. Use these helper functions at appropriate places
to get the CP ring ID.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 57500 chips, the original bnxt_cp_ring_info struct now refers to the
NQ. bp->cp_nr_rings refer to the number of NQs on 57500 chips. There
are now 2 pointers for the CP rings associated with RX and TX rings.
Modify bnxt_alloc_cp_rings() and bnxt_free_cp_rings() accordingly.
With multiple CP rings per NAPI, we need to add a pointer in
bnxt_cp_ring_info struct to point back to the bnxt_napi struct.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ring reservation functions have to be modified for P5 chips in the
following ways:
- bnxt_cp_ring_info structs map to internal NQs as well as CP rings.
- Ring groups are not used.
- 1 CP ring must be available for each RX or TX ring.
- number of RSS contexts to reserve is multiples of 64 RX rings.
- RFS currently not supported.
Also, RX AGG rings are only used for jumbo frames, so we need to
unconditionally call bnxt_reserve_rings() in __bnxt_open_nic()
to see if we need to reserve AGG rings in case MTU has changed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the maximum MSIX capability in PCIe config. space earlier. When
we call firmware to query capability, we need to compare the PCIe
MSIX max count with the firmware count and use the smaller one as
the MSIX count for 57500 (P5) chips.
The new chips don't use ring groups. But previous chips do and
the existing logic limits the available rings based on resource
calculations including ring groups. Setting the max ring groups to
the max rx rings will work on the new chips without changing the
existing logic.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57500 series chips have a new 64-bit doorbell format. Use a new
bnxt_db_info structure to unify the new and the old 32-bit doorbells.
Add a new bnxt_set_db() function to set up the doorbell addreses and
doorbell keys ahead of time. Modify and introduce new doorbell
helpers to help abstract and unify the old and new doorbells.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
57500 series is a new chip class (P5) that requires some driver changes
in the next several patches. This adds basic chip ID, doorbells, and
the notification queue (NQ) structures. Each MSIX is associated with an
NQ instead of a CP ring in legacy chips. Each NQ has up to 2 associated
CP rings for RX and TX. The same bnxt_cp_ring_info struct will be used
for the NQ.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call firmware to configure the DMA addresses of all context memory
pages on new devices requiring context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New device requires host context memory as a backing store. Call
firmware to check for context memory requirements and store the
parameters. Allocate host pages accordingly.
We also need to move the call bnxt_hwrm_queue_qportcfg() earlier
so that all the supported hardware queues and the IDs are known
before checking and allocating context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer chips require the PTU_PTE_VALID bit to be set for every page
table entry for context memory and rings. Additional bits are also
required for page table entries for all rings. Add a flags field to
bnxt_ring_mem_info struct to specify these additional bits to be used
when setting up the pages tables as needed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DMA page table and vmem fields in bnxt_ring_struct to a new
bnxt_ring_mem_info struct. This will allow context memory management
for a new device to re-use some of the existing infrastructure.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware spec. allows interrupt coalescing parameters, such as
maximums, timer units, supported features to be queried. Update
the driver to make use of the new call to query these parameters
and provide the legacy defaults if the call is not available.
Replace the hard-coded values with these parameters.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the max_ext_req_len field from the HWRM_VER_GET_RESPONSE.
If this field is valid and greater than the mailbox size, use the
short command format to send firmware messages greater than the
mailbox size. Newer devices use this method to send larger messages
to the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest firmware spec. has some additional rx extended port stats and new
tx extended port stats added. We now need to check the size of the
returned rx and tx extended stats and determine how many counters are
valid. New counters added include CoS byte and packet counts for rx
and tx.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Among the new changes are trusted VF support, 200Gbps support, and new
API to dump ring information on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_INFO message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_device_detach() stops all tx queues already, so we don't need
this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify this function, no functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added driver causes a warning about a function that is
not used anywhere:
drivers/net/ethernet/marvell/octeontx2/af/cgx.c:320:12: error: 'cgx_fwi_link_change' defined but not used [-Werror=unused-function]
Remove it for now, until a user gets added. If we want to use this
function from another module, we also need a declaration in a header
file, which is currently missing, so it would have to change anyway.
Fixes: 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit makes it possible to use devlink to split the 100G CXP
Netronome into two 40G interfaces. Currently when you ask for 2
interfaces, the math in src/nfp_devlink.c:nfp_devlink_port_split
calculates that you want 5 lanes per port because for some reason
eth_port.port_lanes=10 (shouldn't this be 12 for CXP?). What we really
want when asking for 2 breakout interfaces is 4 lanes per port. This
commit makes that happen by calculating based on 8 lanes if 10 are
present.
Signed-off-by: Ryan C Goodfellow <rgoodfel@isi.edu>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Greg Weeks <greg.weeks@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware ArchDef, the PTV1 field in FD[CTRL]
is ignored by WRIOP, so setting it for Tx FDs is pointless.
Remove all references to it from the code.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ch parameter is never used in the dpaa2_eth_tx_conf function but
since its prototype must match the type defined in the consume field of
struct dpaa2_eth_fq, just mark it as __always_unused.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priv parameter is never used in the build_linear_skb and
drain_channel function. Remove it from the function definitions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 3 cases of possible uninitialized variables are false
positives since they are used only as output parameters.
Nonetheless, fix the warnings.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2_eth_set_dist_key function is only used in a single file.
Make it static.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ARCH_LAYERSCAPE and COMPILE_TEST dependencies are already implied
through the FSL_MC_BUS dep, so there's no need to state it explicitly.
Also, the fsl-mc bus depends on COMPILE_TEST only for some
architectures (arm, arm64, ppc, x86), so it's not correct to
claim build support unconditionally.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dual-emac mode the cpsw driver sends directed packets, that means
that packets go to the directed port, but an ALE lookup is performed
to determine untagged egress only. It means that on tx side no need
to add port bit for ALE mcast entry mask, and basically ALE entry
for port identification is needed only on rx side.
So, add only host port in dual_emac mode as used directed
transmission, and no need in one more port. For single port boards
and switch mode all ports used, as usual, so no changes for them.
Also it simplifies farther changes.
In other words, mcast entries for dual-emac should behave exactly
like unicast. It also can help avoid leaking packets between ports
with same vlan on h/w level if ports could became members of same vid.
So now, for instance, if mcast address 33:33:00:00:00:01 is added then
entries in ALE table:
vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x1
vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x1
Instead of:
vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x3
vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x5
With the same considerations, set only host port for unregistered
mcast for dual-emac mode in case of IFF_ALLMULTI is set, exactly like
it's done in cpsw_ale_set_allmulti().
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever kernel or user decides to call rx mode update, it clears
every multicast entry from forwarding table and in some time adds
it again. This time can be enough to drop incoming multicast packets.
That's why clear only staled multicast entries and update or add new
one afterwards.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It allows to use function under callbacks with same const qualifier of
mac address for farther changes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On GENETv5, there is a hardware issue which prevents the GENET hardware
from generating a link UP interrupt when the link is operating at
10Mbits/sec. Since we do not have any way to configure the link
detection logic, fallback to polling in that case.
Fixes: 421380856d ("net: bcmgenet: add support for the GENETv5 hardware")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbvqcMAAoJEEg/ir3gV/o+eFsH/2TbJH+i1BuGMVwCB8o+U1Rz
C01pJmR7Lb7WwQZ8ZKTOqQkS7BkGX1hNGyIlc4i6ZnP+4gsVJAbP6LKPjTvyD7e6
TNb8bvxTUCOovknrevKkGba8tzoTTsC4wwwbHLGHd1hkKSY1P5hXg8R7vpear+n6
/PFJwzpIXDAa8AHqeORCNYj7MneUm3kaahcmSOxOhvDbRx3UG9cgy7tEhPjZbRn5
jPFsxFCSPcGedtI+g8bzodmpneTcu1KF6QCunrl2bGt5EzgDrbaw1UUoctxD2CJR
Ch45W807EvBJoFiJXXCNf9N+p5020F/Q+mTmK7khPirUjdtoLdcT9Goswpjfbtk=
=vJIA
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-10-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-10-10
This pull request includes some fixes to mlx5 driver,
Please pull and let me know if there's any problem.
For -stable v4.11:
('net/mlx5: Take only bit 24-26 of wqe.pftype_wq for page fault type')
For -stable v4.17:
('net/mlx5: Fix memory leak when setting fpga ipsec caps')
For -stable v4.18:
('net/mlx5: WQ, fixes for fragmented WQ buffers API')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IPoIB netlink support and mlx5e pre-allocated netdevice initialization
IP link was broken due to the changes in IPoIB for the rdma_netdev
support after commit cd565b4b51
("IB/IPoIB: Support acceleration options callbacks").
This patchset fixes IPoIB pkey creation and removal using rtnetlink by
adding support in both IPoIB ULP layer and mlx5 layer:
From Jason and Denis:
1) Introduces changes in the RDMA netdev code in order to
allow allocation of the netdev to be done by the rtnl netdev code.
2) Reworks IPoIB initialization to use the two step rdma_netdev
creation.
From Feras and Saeed, mlx5e netdev layer refactoring to allow accepting
pre-allocated netdevs:
3) Adds support to initialize/cleanup netdevs that are not created
by mlx5 driver.
4) Change mlx5e netdevice layer to accept the pre-allocated netdevice
queue number.
5) Initialize mlx5e generic structures in one place to be used for all
netdevs types NIC/representors/IPoIB (both mlx5 allocated and
pre-allocted).
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbvqHhAAoJEEg/ir3gV/o+TRQH+wYWgvi5AbqYlGpT8xSho8Dg
5tuFE9AbYDGLLWptZgtYXsBsTaltGVqKnwWy//dAuuSI7LvqtjeKqq0G1JKau70L
/49+vv8NTQ6vov2yY95yzzEo5B1/zVcYEl9dmJl4y6Xlwc+YIteewReVqRj+tucR
xO7ghLWc1o4Pl7gWBAcOULyOsZc+CtG8ElwEaBROXTtYRpsR7FKn7vN+WdWZ2VOG
MjtCUaG0vZlK1vaF76J3P9bL2V3y6o6i6S8RZwg1kPxO4jnrzyGrkxWMOX6f32KB
JAUcLVlJW5wckcRAKfTwLxsFMrc9vLBPHyj4XneXVWGKh8/dGUGY5gdGIJV5Jlc=
=m0tM
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-10-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-10-10
IPoIB netlink support and mlx5e pre-allocated netdevice initialization
IP link was broken due to the changes in IPoIB for the rdma_netdev
support after commit cd565b4b51
("IB/IPoIB: Support acceleration options callbacks").
This patchset fixes IPoIB pkey creation and removal using rtnetlink by
adding support in both IPoIB ULP layer and mlx5 layer:
From Jason and Denis:
1) Introduces changes in the RDMA netdev code in order to
allow allocation of the netdev to be done by the rtnl netdev code.
2) Reworks IPoIB initialization to use the two step rdma_netdev
creation.
From Feras and Saeed, mlx5e netdev layer refactoring to allow accepting
pre-allocated netdevs:
3) Adds support to initialize/cleanup netdevs that are not created
by mlx5 driver.
4) Change mlx5e netdevice layer to accept the pre-allocated netdevice
queue number.
5) Initialize mlx5e generic structures in one place to be used for all
netdevs types NIC/representors/IPoIB (both mlx5 allocated and
pre-allocted).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally, we have an issue where r8169 MSI-X interrupt is broken after
S3 suspend/resume on RTL8106e of ASUS X441UAR.
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Capabilities: [d0] Vital Product Data
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 01-00-00-00-36-4c-e0-00
Capabilities: [170] Latency Tolerance Reporting
Kernel driver in use: r8169
Kernel modules: r8169
We found the all of the values in PCI BAR=4 of the ethernet adapter
become 0xFF after system resumes. That breaks the MSI-X interrupt.
Therefore, we can only fall back to MSI interrupt to fix the issue at
that time.
However, there is a commit which resolves the drivers getting nothing in
PCI BAR=4 after system resumes. It is 04cb3ae895d7 "PCI: Reprogram
bridge prefetch registers on resume" by Daniel Drake.
After apply the patch, the ethernet adapter works fine before suspend
and after resume. So, we can revert the workaround after the commit
"PCI: Reprogram bridge prefetch registers on resume" is merged into main
tree.
This patch reverts commit 7bb05b85bc
"r8169: don't use MSI-X on RTL8106e".
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=201181
Fixes: 7bb05b85bc ("r8169: don't use MSI-X on RTL8106e")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resumes promisc mode and vlan filter status after
loopback test.
Fixes: 3b75c3df59 ("net: hns3: net: hns3: Add support for IFF_ALLMULTI flag")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resumes promisc mode and vlan filter status after reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver does nothing when mac vlan table is full.
In this case, the packet with new mac address will be dropped
by hardware. This patch adds check for the result of sync mac
address, and enable promisc mode when mac vlan table is full.
Furtherly, disable vlan filter when enable promisc by user
command.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the repeated license text with SDPX identifiers.
While at it bump the Copyright dates for files we touched
this year.
Signed-off-by: Edwin Peer <edwin.peer@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Nic Viljoen <nick.viljoen@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that since
commit 05212ba813 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
at least RTL_GIGA_MAC_VER_38 NICs work erratically after a resume from
suspend.
The problem has been traced to a missing RX_MULTI_EN bit in the RxConfig
register.
We already set this bit for RTL_GIGA_MAC_VER_35 NICs of the same 8168F
chip family so let's do it also for its other siblings: RTL_GIGA_MAC_VER_36
and RTL_GIGA_MAC_VER_38.
Curiously, the NIC seems to work fine after a system boot without having
this bit set as long as the system isn't suspended and resumed.
Fixes: 05212ba813 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Reported-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 63ae7949e9 ("net: socionext: Use descriptor info instead of MMIO reads on Rx")
removed constant mmio reads from the driver and started using a descriptor
field to check if packet should be processed.
This lead the napi rx handler being constantly called while no packets
needed processing and ksoftirq getting 100% cpu usage. Issue one mmio read
to clear the irq correcty after processing packets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During boot, mlx4_core sets the driverinit configuration parameters and
updates the devlink module on the initial values calling
devlink_param_driverinit_value_set().
If devlink_param_driverinit_value_set() returns an error mlx4_core
reports kernel module warning.
This caused false alarm during boot in case kernel was compiled with
CONFIG_NET_DEVLINK off.
Fix by removing warning reported in case
devlink_param_driverinit_value_set() fails.
This actually makes the function mlx4_devlink_set_init_value()
redundant to using directly devlink_param_driverinit_value_set() and so
removed.
It fixes the following kernel trace:
mlx4_core 0000:00:06.0: devlink set parameter 0 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 1 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 4 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 5 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 3 value failed (err = -95)
Fixes: bd1b51dc66 ("mlx4: Add mlx4 initial parameters table and register it")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_THERMAL=m, we get a build error:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.c: In function 'cxgb4_thermal_get_trip_type':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.c:48:11: error: 'struct adapter' has no member named 'ch_thermal'
Once that is fixed by using IS_ENABLED() checks, we get a link error
against the thermal subsystem when cxgb4 is built-in:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_init':
cxgb4_thermal.c:(.text+0x180): undefined reference to `thermal_zone_device_register'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_remove':
cxgb4_thermal.c:(.text+0x1e0): undefined reference to `thermal_zone_device_unregister'
Finally, since CONFIG_THERMAL can be =m, the Makefile fails to pick up the
extra file into built-in.a, and we get another link failure against the
cxgb4_thermal_init/cxgb4_thermal_remove files, so the Makefile has to
be adapted as well to work for both CONFIG_THERMAL=y and =m.
Fixes: b187191577 ("cxgb4: Add thermal zone support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant spinlock acquire parameter from ena_com_admin_init()
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improves socket memory utilization when receiving packets larger
than 128 bytes (the previous rx copybreak) and smaller than 256 bytes.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently Rx refill is done when the number of required descriptors is
above 1/8 queue size. With a default of 1024 entries per queue the
threshold is 128 descriptors.
There is intention to increase the queue size to 8196 entries.
In this case threshold of 1024 descriptors is too large and can hurt
latency.
Add another limitation to Rx threshold to be at most 256 descriptors.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set skb->ip_summed to the correct value as reported by the device.
Add counter for the case where rx csum offload is enabled but
device didn't check it.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes all code changes necessary in ena_netdev to enable
packet sending via the LLQ placemnt mode.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces APIs for detection, initialization, configuration
and actual usage of low latency queues(LLQ). It extends transmit API with
creation of LLQ descriptors in device memory (which include host buffers
descriptors as well as packet header)
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Low Latency Queues(LLQ) allow usage of device's memory for descriptors
and headers. Such queues decrease processing time since data is already
located on the device when driver rings the doorbell.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields and definitions to host info and fill them
according to the latest ENA spec version.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce fastpath overhead by making ena_com_tx_comp_req_id_get() inline.
Also move it to ena_eth_com.h file with its dependency function
ena_com_cq_inc_head().
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DECAP_ECN0 trap will be used to trap packets where the overlay
packet is marked with Non-ECT, but the underlay packet is marked with
either ECT(0), ECT(1) or CE. When trapped, such packets will be counted
as errors by the VxLAN driver and thus provide better visibility.
The NVE_ENCAP_ARP trap will be used to trap ARP packets undergoing NVE
encapsulation. This is needed in order to support E-VPN ARP suppression,
where the Linux bridge does not flood ARP packets through tunnel ports
in case it can answer the ARP request itself.
Note that all the packets trapped via these traps are marked with
'offload_fwd_mark', so as to not be re-flooded by the Linux bridge
through the ASIC ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following resources to be used by the NVE code:
* Number of IPv4 underlay destination IPs in a single TNUMT record
* Number of IPv6 underlay destination IPs in a single TNUMT record
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used for setting up the parsing for hash, policy-engine
and routing.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be used to program the device with FDB records pointing to a NVE
tunnel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TNQDR register configures the default QoS settings for NVE
encapsulation.
It will be used to set the default DSCP of each port to 0, so that when
DSCP is set to inherit and the overlay packet does not have an IP header
the outer DSCP will be set to 0, in accordance with the software data
path.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register configures how QoS is set in Encapsulation into the
underlay network.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures the actions that are done during NVE
decapsulation based on the ECN bits.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register performs mapping from overlay ECN to underlay ECN during
NVE encapsulation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register builds the linked list of underlay destination IPs used
for BUM traffic on the overlay.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register enables / disables learning on different types of tunnel
ports (e.g., NVE, VPLS).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures global NVE configuration such as source IP of
the NVE tunnel and UDP source port calculation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the seed of the LAG hash function is always set to 0, which
means it is identical across all switches. Instead, use a random number.
This is especially important now that VxLAN is supported, as the LAG
hash function is used to calculate the UDP source port of the
encapsulated packet.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device has the ability to flush all the FDB records that perform NVE
encapsulation or only a subset of these with a specific filtering
identifier (FID).
Expose these types so that they could be used by subsequent patches
where we need to flush the FDB records when an NVE device is unlinked
from a bridge (FID).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device needs to flood an overlay packet to remote VTEPs it
retrieves a pointer to the head of a linked-list of records that store
the IP addresses of these VTEPs.
These records are stored in the KVD linear memory and configured via the
Tunneling NVE Underlay Multicast Table (TNUMT) register.
Add a new KVD linear entry type for these records, so that we will be
able to allocate and free them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L3 protocol and address definitions are going to be used by the NVE
code, so move them to the global header file from the one private to the
router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VxLAN notifications are going to use a different notifier information
type, so cast to the correct type based on the received event.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VxLAN FDB updates are sent with the VxLAN device which is not our upper
and will therefore be ignored by current code.
Solve this by checking whether the upper device (bridge) is our upper.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VxLAN FDB notifications need to be handled differently than bridge FDB
notifications, so initialize the work item based on the received
notification and rename the invoked function accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spectrum_router.h header file is private to the router block and
should only be included by direct consumers of it, such as dpipe and the
multicast routing code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/cgx.c: In function 'cgx_fwi_event_handler':
drivers/net/ethernet/marvell/octeontx2/af/cgx.c:257:17: warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
It never be used since introduction in
commit 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the NETIF_F_RXFCS feature in the Mscc
Ethernet driver. This feature is disabled by default and allow a user
to request the driver not to drop the FCS and to extract it into the skb
for debugging purposes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RSS tuple support for VF in revision
0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RSS key, hash algorithm configuration support
for VF in revision 0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ETH_RSS_HASH_XOR hash algorithm supports, which
is supported by hw revision 0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the host context count symbols provided by firmware and use
it to determine the number of allocated stats ids. Previously it
won't be possible to offload more than 2^17 filter even if FW was
able to do so.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of an array stats instead of storing stats per flow which
would require a hash lookup at critical times.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of relativistic hash tables for tracking flows instead
of fixed sized hash tables.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several variables being initialized that are being set later
and hence the initialization is redundant and can be removed. Remove
then.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5e netdevice used to calculate fragment edges by a call to
mlx5_wq_cyc_get_frag_size(). This calculation did not give the correct
indication for queues smaller than a PAGE_SIZE, (broken by default on
PowerPC, where PAGE_SIZE == 64KB). Here it is replaced by the correct new
calls/API.
Since (TX/RX) Work Queues buffers are fragmented, here we introduce
changes to the API in core driver, so that it gets a stride index and
returns the index of last stride on same fragment, and an additional
wrapping function that returns the number of physically contiguous
strides that can be written contiguously to the work queue.
This obsoletes the following API functions, and their buggy
usage in EN driver:
* mlx5_wq_cyc_get_frag_size()
* mlx5_wq_cyc_ctr2fragix()
The new API improves modularity and hides the details of such
calculation for mlx5e netdevice and mlx5_ib rdma drivers.
New calculation is also more efficient, and improves performance
as follows:
Packet rate test: pktgen, UDP / IPv4, 64byte, single ring, 8K ring size.
Before: 16,477,619 pps
After: 17,085,793 pps
3.7% improvement
Fixes: 3a2f703312 ("net/mlx5: Use order-0 allocations for all WQ types")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The HW spec defines only bits 24-26 of pftype_wq as the page fault type,
use the required mask to ensure that.
Fixes: d9aaed8387 ("{net,IB}/mlx5: Refactor page fault handling")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allocated memory for context should be freed once
finished working with it.
Fixes: d6c4f0298c ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current design of mlx5e driver ignores the netdevice TX/RX queues
number for netdevices that RDMA IPoIB ULP creates. Instead, the queue
number is initialized to the maximum number that mlx5 thinks best for
performance. As a result, ULP drivers that choose to create a netdevice
with queue number that is less than the maximum channels mlx5 creates,
will get a memory corruption.
This fix changes the mlx5e netdev logic to respect ULP netdevices TX/RX
queue number and use it when creating resources instead of the maximum
channel number.
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Convert mlx5e update stats work to a normal work structure, since it is
never used delayed.
Add a helper function to queue update stats work on demand which checks
for some conditions and reduce code duplication to have a better
abstraction.
Fixes: ed56c5193a ("net/mlx5e: Update NIC HW stats on demand only")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move all mlx5e generic structures initializations to mlx5e_netdev_init.
The common structure new initializer function will be used to initialize
mlx5 context for netlink created netdevs such as IPoIB mlx5 accelerated
child netdevs.
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
mlx5e_detach_netdev cancels update_stats work which was not initialized
in ipoib netdevice profile, as a result, the following assert occurs:
ODEBUG: assert_init not available (active state 0) object type:
timer_list hint:(null)
This change moves the update stats work to be initialized for all
mlx5e netdevices.
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce a helper init/cleanup function that initializes mlx5e generic
netdev private structure, and use them from all profiles init/cleanup
callbacks.
This patch will also be helpful to initialize/cleanup netdevs that are
not created by mlx5 driver, e.g: accelerated ipoib child netdevs.
Fixes: 26e59d8077 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
netdev has several interfaces that expect to call alloc_netdev_mqs from
the core code, with the driver only providing the arguments. This is
incompatible with the rdma_netdev interface that returns the netdev
directly.
Thus re-organize the API used by ipoib so that the verbs core code calls
alloc_netdev_mqs for the driver. This is done by allowing the drivers to
provide the allocation parameters via a 'get_params' callback and then
initializing an allocated netdev as a second step.
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added support in RVU AF driver to register for
CGX LMAC link status change events from firmware
and managing them. Processing part will be added
in followup patches.
- Introduced eventqueue for posting events from cgx lmac.
Queueing mechanism will ensure that events can be posted
and firmware can be acked immediately and hence event
reception and processing are decoupled.
- Events gets added to the queue by notification callback.
Notification callback is expected to be atomic, since it
is called from interrupt context.
- Events are dequeued and processed in a worker thread.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CGX LMAC initialization, link status polling etc is done
by low level secure firmware. For link management this patch
adds a interface or communication mechanism between firmware
and this kernel CGX driver.
- Firmware interface specification is defined in cgx_fw_if.h.
- Support to send/receive commands/events to/form firmware.
- events/commands implemented
* link up
* link down
* reading firmware version
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Nithya Mani <nmani@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each of the enabled CGX LMAC is considered a physical
interface and RVU PFs are mapped to these. VFs of these
SRIOV PFs will be virtual interfaces and share CGX LMAC
along with PF.
This mapping info will be used later on for Rx/Tx pkt steering.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic template for Marvell OcteonTX2's
CGX ethernet interface driver. Just the probe.
RVU AF driver will use APIs exported by this driver
for various things like PF to physical interface mapping,
loopback mode, interface stats etc. Hence marged both
drivers into a single module.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW interprets RVU_AF_MSIXTR_BASE address as an IOVA, hence
create a IOMMU mapping for the physcial address configured by
firmware and reconfig RVU_AF_MSIXTR_BASE with IOVA.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware configures a certain number of MSIX vectors to each of
enabled RVU PF/VF. When a block LF is attached to a PF/VF, number
of MSIX vectors needed by that LF are set aside (out of PF/VF's
total MSIX vectors) and LF's msix_offset is configured in HW.
Also added support for a RVU PF/VF to retrieve that block LF's
MSIX vector offset information from AF via mbox.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for a RVU PF/VF to request AF via mailbox
to attach or detach NPA/NIX/SSO/SSOW/TIM/CPT block LFs.
Also supports partial detachment and modifying current
LF attached count of a certian block type.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scan all RVU blocks to find any 'LF to RVU PF/VF' mapping done by
low level firmware. If found any, mark them as used in respective
block's LF bitmap and also save mapped PF/VF's PF_FUNC info.
This is done to avoid reattaching a block LF to a different RVU PF/VF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 10's of mailbox messages expected to be handled in future,
checking for message id could become a lengthy switch case. Hence
added a macro to auto generate the switch case for each msg id.
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for mailbox interrupt and message
handling. Mapped mailbox region and registered a workqueue
for message handling. Enabled mailbox IRQ of RVU PFs
and registered a interrupt handler. When IRQ is triggered
work is added to the mbox workqueue for msgs to get processed.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds mailbox support infrastructure APIs.
Each RVU device has a dedicated 64KB mailbox region
shared with it's peer for communication. RVU AF has
a separate mailbox region shared with each of RVU PFs
and a RVU PF has a separate region shared with each of
it's VF.
These set of APIs are used by this driver (RVU AF) and
other RVU PF/VF drivers eg netdev, crypto e.t.c.
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gathers NPA/NIX/SSO/SSOW/TIM/CPT RVU blocks's
HW info like number of LFs. Important register offsets
saved for later use to avoid code duplication for each block.
A bitmap is allocated for each of the blocks which later
on will be used to allocate a LF for a RVU PF/VF.
Also added RVU NIX/NPA block registers and few registers
of other blocks.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Go through all BLKADDRs and check which ones are implemented
on this silicon and do a HW reset of each implemented block.
Also added all RVU AF and PF register offsets.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic template for Marvell OcteonTX2's
resource virtualization unit (RVU) admin function (AF)
driver. Just the driver registration and probe.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently driver registers to physical link notifications (of the device)
from Management firmware (MFW). Driver doesn't get notified if there's a
change in the virtual link e.g., link-flap on the peer PF interface.
Virtual link indication from MFW reflects the per PF link status instead
of the physical link.
The patch adds driver support for,
- Advertising the virtual link support to MFW.
- Handling the virtual link notification from MFW.
Please consider applying it to 'net-next'.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add thermal zone support to monitor ASIC's temperature.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When memory is limited (on kdump kernel), reduce size of rx and tx rings.
Also reduce the number of rx rings.
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate potential auto casting compilation error.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi poll functions should be initialized before running request_irq(),
to handle a rare condition where there is a pending interrupt, causing
the ISR to fire immediately while the poll function wasn't set yet,
causing a NULL dereference.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a rare scenario when ena_device_restore() fails, followed by device
remove, an FLR will not be issued. In this case, the device will keep
sending asynchronous AENQ keep-alive events, even after driver removal,
leading to memory corruption.
Fixes: 8c5c7abdeb ("net: ena: add power management ops to the ENA driver")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory mapped with devm_ioremap is automatically freed when the driver
is disconnected from the device. Therefore there is no need to
explicitly call devm_iounmap.
Fixes: 0857d92f71 ("net: ena: add missing unmap bars on device removal")
Fixes: 411838e7b4 ("net: ena: fix rare kernel crash when bar memory remap fails")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-10-08
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) sk_lookup_[tcp|udp] and sk_release helpers from Joe Stringer which allow
BPF programs to perform lookups for sockets in a network namespace. This would
allow programs to determine early on in processing whether the stack is
expecting to receive the packet, and perform some action (eg drop,
forward somewhere) based on this information.
2) per-cpu cgroup local storage from Roman Gushchin.
Per-cpu cgroup local storage is very similar to simple cgroup storage
except all the data is per-cpu. The main goal of per-cpu variant is to
implement super fast counters (e.g. packet counters), which don't require
neither lookups, neither atomic operations in a fast path.
The example of these hybrid counters is in selftests/bpf/netcnt_prog.c
3) allow HW offload of programs with BPF-to-BPF function calls from Quentin Monnet
4) support more than 64-byte key/value in HW offloaded BPF maps from Jakub Kicinski
5) rename of libbpf interfaces from Andrey Ignatov.
libbpf is maturing as a library and should follow good practices in
library design and implementation to play well with other libraries.
This patch set brings consistent naming convention to global symbols.
6) relicense libbpf as LGPL-2.1 OR BSD-2-Clause from Alexei Starovoitov
to let Apache2 projects use libbpf
7) various AF_XDP fixes from Björn and Magnus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, both Rx and Tx confirmation frames handled during
NAPI poll were counted toward the NAPI budget. However, Tx
confirmations are lighter to process than Rx frames, which can
skew the amount of work actually done inside one NAPI cycle.
Update the code to only count Rx frames toward the NAPI budget
and set a separate threshold on how many Tx conf frames can be
processed in one poll cycle.
The NAPI poll routine stops when either the budget is consumed
by Rx frames or when Tx confirmation frames reach this threshold.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mscc/ocelot_board.c: In function 'mscc_ocelot_probe':
drivers/net/ethernet/mscc/ocelot_board.c:262:17: warning:
variable 'phy_mode' set but not used [-Wunused-but-set-variable]
enum phy_mode phy_mode;
It never used since introduction in
commit 71e32a20cf ("net: mscc: ocelot: make use of SerDes PHYs for handling their configuration")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix and improve dpaa2-ptp driver
in some places.
- Fixed the return for some functions.
- Replaced kzalloc with devm_kzalloc.
- Removed dev_set_drvdata(dev, NULL).
- Made ptp_dpaa2_caps const.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to removed unused code for dprtc.
This code will be re-added along with more features
of dpaa2-ptp added.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dpaa2-ptp driver, it's odd to use rtc in names of
some functions and structures except these dprtc APIs.
This patch is to use ptp instead of rtc in names.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETDEVICES dependency and ETHERNET dependency hadn't
been required since dpaa2-eth was moved out of staging.
Also allowed COMPILE_TEST for dpaa2-eth.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move DPAA2 PTP driver out of staging/
since the dpaa2-eth had been moved out.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark instructions that use pointers to areas in the stack outside of the
current stack frame, and process them accordingly in mem_op_stack().
This way, we also support BPF-to-BPF calls where the caller passes a
pointer to data in its own stack frame to the callee (typically, when
the caller passes an address to one of its local variables located in
the stack, as an argument).
Thanks to Jakub and Jiong for figuring out how to deal with this case,
I just had to turn their email discussion into this patch.
Suggested-by: Jiong Wang <jiong.wang@netronome.com>
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When pre-processing the instructions, it is trivial to detect what
subprograms are using R6, R7, R8 or R9 as destination registers. If a
subprogram uses none of those, then we do not need to jump to the
subroutines dedicated to saving and restoring callee-saved registers in
its prologue and epilogue.
This patch introduces detection of callee-saved registers in subprograms
and prevents the JIT from adding calls to those subroutines whenever we
can: we save some instructions in the translated program, and some time
at runtime on BPF-to-BPF calls and returns.
If no subprogram needs to save those registers, we can avoid appending
the subroutines at the end of the program.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
On performing a BPF-to-BPF call, we first jump to a subroutine that
pushes callee-saved registers (R6~R9) to the stack, and from there we
goes to the start of the callee next. In order to do so, the caller must
pass to the subroutine the address of the NFP instruction to jump to at
the end of that subroutine. This cannot be reliably implemented when
translated the caller, as we do not always know the start offset of the
callee yet.
This patch implement the required fixup step for passing the start
offset in the callee via the register used by the subroutine to hold its
return address.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Relocation for targets of BPF-to-BPF calls are required at the end of
translation. Update the nfp_fixup_branches() function in that regard.
When checking that the last instruction of each bloc is a branch, we
must account for the length of the instructions required to pop the
return address from the stack.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Offloaded programs using BPF-to-BPF calls use the stack to store the
return address when calling into a subprogram. Callees also need some
space to save eBPF registers R6 to R9. And contrarily to kernel
verifier, we align stack frames on 64 bytes (and not 32). Account for
all this when checking the stack size limit before JIT-ing the program.
This means we have to recompute maximum stack usage for the program, we
cannot get the value from the kernel.
In addition to adapting the checks on stack usage, move them to the
finalize() callback, now that we have it and because such checks are
part of the verification step rather than translation.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This is the main patch for the logics of BPF-to-BPF calls in the nfp
driver.
The functions called on BPF_JUMP | BPF_CALL and BPF_JUMP | BPF_EXIT were
used to call helpers and exit from the program, respectively; make them
usable for calling into, or returning from, a BPF subprogram as well.
For all calls, push the return address as well as the callee-saved
registers (R6 to R9) to the stack, and pop them upon returning from the
calls. In order to limit the overhead in terms of instruction number,
this is done through dedicated subroutines. Jumping to the callee
actually consists in jumping to the subroutine, that "returns" to the
callee: this will require some fixup for passing the address in a later
patch. Similarly, returning consists in jumping to the subroutine, which
pops registers and then return directly to the caller (but no fixup is
needed here).
Return to the caller is performed with the RTN instruction newly added
to the JIT.
For the few steps where we need to know what subprogram an instruction
belongs to, the struct nfp_insn_meta is extended with a new subprog_idx
field.
Note that checks on the available stack size, to take into account the
additional requirements associated to BPF-to-BPF calls (storing R6-R9
and return addresses), are added in a later patch.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Similarly to "exit" or "helper call" instructions, BPF-to-BPF calls will
require additional processing before translation starts, in order to
record and mark jump destinations.
We also mark the instructions where each subprogram begins. This will be
used in a following commit to determine where to add prologues for
subprograms.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The checks related to eBPF helper calls are performed each time the nfp
driver meets a BPF_JUMP | BPF_CALL instruction. However, these checks
are not relevant for BPF-to-BPF call (same instruction code, different
value in source register), so just skip the checks for such calls.
While at it, rename the function that runs those checks to make it clear
they apply to _helper_ calls only.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In order to support BPF-to-BPF calls in offloaded programs, the nfp
driver must collect information about the distinct subprograms: namely,
the number of subprograms composing the complete program and the stack
depth of those subprograms. The latter in particular is non-trivial to
collect, so we copy those elements from the kernel verifier via the
newly added post-verification hook. The struct nfp_prog is extended to
store this information. Stack depths are stored in an array of dedicated
structs.
Subprogram start indexes are not collected. Instead, meta instructions
associated to the start of a subprogram will be marked with a flag in a
later patch.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In preparation for support for BPF to BPF calls in offloaded programs,
rename the "stack_depth" field of the struct nfp_prog as
"stack_frame_depth". This is to make it clear that the field refers to
the maximum size of the current stack frame (as opposed to the maximum
size of the whole stack memory).
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In preparation for BPF-to-BPF calls in offloaded programs, add a new
function attribute to the struct bpf_prog_offload_ops so that drivers
supporting eBPF offload can hook at the end of program verification, and
potentially extract information collected by the verifier.
Implement a minimal callback (returning 0) in the drivers providing the
structs, namely netdevsim and nfp.
This will be useful in the nfp driver, in later commits, to extract the
number of subprograms as well as the stack depth for those subprograms.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
There is no need to compare *val.vu32* with < 0 because
such variable is of type u32 (32 bits, unsigned), making it
impossible to hold a negative value. Fix this by removing
such comparison.
Also, initialize variable *max_val* to -1, just in case
it is not initialized to either BNXT_MSIX_VEC_MAX or
BNXT_MSIX_VEC_MIN_MAX before using it in a comparison
with val.vu32 at line 159:
if (val.vu32 > max_val)
Addresses-Coverity-ID: 1473915 ("Unsigned compared against 0")
Addresses-Coverity-ID: 1473920 ("Uninitialized scalar variable")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading the L3 and L4 csum computation on TX, we need to extract
the l3_proto from the ethtype, independently of the presence of a vlan
tag.
The actual driver uses skb->protocol as-is, resulting in packets with
the wrong L4 checksum being sent when there's a vlan tag in the packet
header and checksum offloading is enabled.
This commit makes use of vlan_protocol_get() to get the correct ethtype
regardless the presence of a vlan tag.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the SerDes muxing was hardcoded to a given mode in the MAC
controller driver. Now, the SerDes muxing is configured within the
Device Tree and is enforced in the MAC controller driver so we can have
a lot of different SerDes configurations.
Make use of the SerDes PHYs in the MAC controller to set up the SerDes
according to the SerDes<->switch port mapping and the communication mode
with the Ethernet PHY.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since HSIO address space can be accessed by different drivers, let's
simplify the register address definitions so that it can be easily used
by all drivers and put the register address definition in the
include/soc/mscc/ocelot_hsio.h header file.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since HSIO address space can be used by different drivers (PLL, SerDes
muxing, temperature sensor), let's move it somewhere it can be included
by all drivers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HSIO address space was moved to a syscon, hence we need to get the
regmap of this address space from there and no more from the device
node.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In revision 0x20, we use vlan id != 0 to check whether a vlan tag
has been offloaded, so vlan id 0 is not supported.
In revision 0x21, rx buffer descriptor adds two bits to indicate
whether one or more vlan tags have been offloaded, so vlan id 0
is valid now.
This patch seperates the handle for vlan id 0, add vlan id 0 support
for revision 0x21.
Fixes: 5b5455a9ed ("net: hns3: Add STRP_TAGP field support for hardware revision 0x21")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In revision 0x21, hw supports both ingress and egress vlan filter.
This patch adds support for it.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For mta table support has been dropped, remove the code for mta table.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In previously implement for unicast mac vlan table, the space is
shared by all the functions, driver does nothing when the space is
exhausted. This patch preallocates the space of unicast mac vlan
table for each function by software. Each function can only use its
private space and available shared space, avoiding single function
exhausts too much space, and other functions are unable to add
unicast mac address.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, the mac vlan table entries are not cleared when
unload hns3 driver. The dirty mac vlan table entries will make the
result of looking up mac vlan table being unexpected.
When doing core reset or global reset, the firmware will clear all
the tables for driver, and driver shouldn't send any commands to
firmware during reset. But when doing function reset, the driver
needs to clear the tables itself.
This patch clears the mac vlan table entries for each client when
unload driver or reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default mask configuration has been done by firmware, so the driver
doesn't need to do it any more.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cxgb_extension_ioctl(), the command of the ioctl is firstly copied from
the user-space buffer 'useraddr' to 'cmd' and checked through the
switch statement. If the command is not as expected, an error code
EOPNOTSUPP is returned. In the following execution, i.e., the cases of the
switch statement, the whole buffer of 'useraddr' is copied again to a
specific data structure, according to what kind of command is requested.
However, after the second copy, there is no re-check on the newly-copied
command. Given that the buffer 'useraddr' is in the user space, a malicious
user can race to change the command between the two copies. By doing so,
the attacker can supply malicious data to the kernel and cause undefined
behavior.
This patch adds a re-check in each case of the switch statement if there is
a second copy in that case, to re-check whether the command obtained in the
second copy is the same as the one in the first copy. If not, an error code
EINVAL is returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
when 32 bit port capability is in use, use FW_PORT_ACTION_L1_CFG32
rather than FW_PORT_ACTION_L1_CFG.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the be2net implementation of .ndo_tunnel_{add,del}() changes the value of
NETIF_F_GSO_UDP_TUNNEL bit in 'features' and 'hw_features', but it forgets
to call netdev_features_change(). Moreover, ethtool setting for that bit
can potentially be reverted after a tunnel is added or removed.
GSO already does software segmentation when 'hw_enc_features' is 0, even
if VXLAN offload is turned on. In addition, commit 096de2f83e ("benet:
stricter vxlan offloading check in be_features_check") avoids hardware
segmentation of non-VXLAN tunneled packets, or VXLAN packets having wrong
destination port. So, it's safe to avoid flipping the above feature on
addition/deletion of VXLAN tunnels.
Fixes: 630f4b7056 ("be2net: Export tunnel offloads only when a VxLAN tunnel is created")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting the max rings supported, get the reduced max_irqs
by the ones used by RDMA.
If the number MSIX is the limiting factor, this bug may cause the
max ring count to be higher than it should be when RDMA driver is
loaded and may result in ring allocation failures.
Fixes: 30f529473e ("bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.
This patch fixes the problem described above.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In HWRM_QUEUE_COS2BW_CFG request, enables field should have the bits
set only for the queue ids which are having the valid parameters.
This causes firmware to return error when the TC to hardware CoS queue
mapping is not 1:1 during DCBNL ETS setup.
Fixes: 2e8ef77ee0 ("bnxt_en: Add TC to hardware QoS queue mapping logic.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG
firmware call to reserve VNICs. This has the effect that the firmware
will keep a large number of VNICs for the PF, and having very few for
VFs. DPDK driver running on the VFs, which requires more VNICs, may not
work properly as a result.
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds following driver-specific permanent mode boolean
parameter.
gre_ver_check - Generic Routing Encapsulation(GRE) version check
will be enabled in the device. If disabled, device skips version
checking for GRE packets.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for following generic permanent mode
devlink parameters. They can be modified using devlink param
commands.
msix_vec_per_pf_max - This param sets the number of MSIX vectors
that the device requests from the host on driver initialization.
This value is set in the device which limits MSIX vectors per PF.
msix_vec_per_pf_min - This param sets the number of minimal MSIX
vectors required for the device initialization. Value 0 indicates
a default value is selected. This value is set in the device which
limits MSIX vectors per PF.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return proper error code when Firmware returns
HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED for HWRM_NVM_GET/SET_VARIABLE
commands.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ignore_ari generic permanent mode
devlink parameter. This parameter is disabled by default. It can be
enabled using devlink param commands.
ignore_ari - If enabled, device ignores ARI(Alternate Routing ID)
capability, even when platforms has the support and creates same number
of partitions when platform does not support ARI capability.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_ll2.c:799:32: warning: implicit
conversion from enumeration type 'enum core_tx_dest' to different
enumeration type 'enum qed_ll2_tx_dest' [-Wenum-conversion]
tx_pkt.tx_dest = p_ll2_conn->tx_dest;
~ ~~~~~~~~~~~~^~~~~~~
1 warning generated.
Fix this by using a switch statement to convert between the enumerated
values since they are not 1 to 1, which matches how the rest of the
driver handles this conversion.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Suggested-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 602b74eda8 ("mlxsw: spectrum_switchdev: Do not leak RIFs
when removing bridge") I handled the case where RIFs created for VLAN
devices were not properly cleaned up when their real device (a bridge)
was removed.
However, I forgot to handle the case of the VLAN device itself being
removed. Do so now when the VLAN device is being unlinked from its real
device.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reported-by: Artem Shvorin <art@qrator.net>
Tested-by: Artem Shvorin <art@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a hardware issue in Spectrum-2, the field event_type of the event
queue element (EQE) has become reserved. It was used to distinguish between
command interface completion events and completion events.
Use queue number to determine event type, as command interface completion
events are always received on EQ0 and mlxsw driver maps completion events
to EQ1.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 core driver and ethernet netdev updates, please note there is a small
devlink releated update to allow extack argument to eswitch operations.
From Eli Britstein,
1) devlink: Add extack argument to the eswitch related operations
2) net/mlx5e: E-Switch, return extack messages for failures in the e-switch devlink callbacks
3) net/mlx5e: Add extack messages for TC offload failures
From Eran Ben Elisha,
4) mlx5e: Add counter for aRFS rule insertion failures
From Feras Daoud
5) Fast teardown support for mlx5 device
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the FW pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been scatter
to memory
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbtU45AAoJEEg/ir3gV/o+/C4H/RHA4KImrb476EdB3VNYMqAN
dgXb+bmh6sZP+jHWqQ4c3aVeh6/T8qm4gwiSn2nVTtHEnxtCdIYljzDC1Nswczeg
pSjD1eOP7M1LpAOmBb8xdnJcX7yM7r1bTklnp2sN853WShbsDRYgZBHsBwTzx25U
ZdzL4QTLuohlG/aLrbGXMntIy45ya2fVQrnK54s18nFlgsdFjEs0mi0xaUKNBC6+
P8CTohHAxuuxmL5b+6MIYLZCdgd8cLNQFdtqbckEVw7SvcRTxfraRlyqJ0YOgTGB
TdSWnqZz2JYH29wSFbpFG8qX6GCv8FoiZ+fKzldbolHk442rrktHv3+Y7qQuZVs=
=NVks
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-10-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-10-03
mlx5 core driver and ethernet netdev updates, please note there is a small
devlink releated update to allow extack argument to eswitch operations.
From Eli Britstein,
1) devlink: Add extack argument to the eswitch related operations
2) net/mlx5e: E-Switch, return extack messages for failures in the e-switch devlink callbacks
3) net/mlx5e: Add extack messages for TC offload failures
From Eran Ben Elisha,
4) mlx5e: Add counter for aRFS rule insertion failures
From Feras Daoud
5) Fast teardown support for mlx5 device
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the FW pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been scatter
to memory
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistakes in dev_dbg warning messages
"Reloade" -> "Reload"
"chang" -> "change"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Today mlx5 devices support two teardown modes:
1- Regular teardown
2- Force teardown
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been scatter
to memory
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Count aRFS rules insertion failure for ethtool output. In addition, move
the error print into debug prints mechanism, as it could flood the dmesg
and reduce system BW dramatically.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Return tc extack messages for failures to user space.
Messages provide reasons for not being able to offload rules to HW.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Return extack messages for failures in the e-switch devlink callbacks.
Messages provide reasons for not being able to issue the operation.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add extack argument to the eswitch related operations.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
David writes:
"Networking fixes:
1) Prefix length validation in xfrm layer, from Steffen Klassert.
2) TX status reporting fix in mac80211, from Andrei Otcheretianski.
3) Fix hangs due to TX_DROP in mac80211, from Bob Copeland.
4) Fix DMA error regression in b43, from Larry Finger.
5) Add input validation to xenvif_set_hash_mapping(), from Jan Beulich.
6) SMMU unmapping fix in hns driver, from Yunsheng Lin.
7) Bluetooh crash in unpairing on SMP, from Matias Karhumaa.
8) WoL handling fixes in the phy layer, from Heiner Kallweit.
9) Fix deadlock in bonding, from Mahesh Bandewar.
10) Fill ttl inherit infor in vxlan driver, from Hangbin Liu.
11) Fix TX timeouts during netpoll, from Michael Chan.
12) RXRPC layer fixes from David Howells.
13) Another batch of ndo_poll_controller() removals to deal with
excessive resource consumption during load. From Eric Dumazet.
14) Fix a specific TIPC failure secnario, from LUU Duc Canh.
15) Really disable clocks in r8169 during suspend so that low
power states can actually be reached.
16) Fix SYN backlog lockdep issue in tcp and dccp, from Eric Dumazet.
17) Fix RCU locking in netpoll SKB send, which shows up in bonding,
from Dave Jones.
18) Fix TX stalls in r8169, from Heiner Kallweit.
19) Fix locksup in nfp due to control message storms, from Jakub
Kicinski.
20) Various rmnet bug fixes from Subash Abhinov Kasiviswanathan and
Sean Tranchetti.
21) Fix use after free in ip_cmsg_recv_dstaddr(), from Eric Dumazet."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (122 commits)
ixgbe: check return value of napi_complete_done()
sctp: fix fall-through annotation
r8169: always autoneg on resume
ipv4: fix use-after-free in ip_cmsg_recv_dstaddr()
net: qualcomm: rmnet: Fix incorrect allocation flag in receive path
net: qualcomm: rmnet: Fix incorrect allocation flag in transmit
net: qualcomm: rmnet: Skip processing loopback packets
net: systemport: Fix wake-up interrupt race during resume
rtnl: limit IFLA_NUM_TX_QUEUES and IFLA_NUM_RX_QUEUES to 4096
bonding: fix warning message
inet: make sure to grab rcu_read_lock before using ireq->ireq_opt
nfp: avoid soft lockups under control message storm
declance: Fix continuation with the adapter identification message
net: fec: fix rare tx timeout
r8169: fix network stalls due to missing bit TXCFG_AUTO_FIFO
tun: napi flags belong to tfile
tun: initialize napi_mutex unconditionally
tun: remove unused parameters
bond: take rcu lock in netpoll_send_skb_on_dev
rtnetlink: Fail dump if target netnsid is invalid
...
The NIC driver should only enable interrupts when napi_complete_done()
returns true. This patch adds the check for ixgbe.
Cc: stable@vger.kernel.org # 4.10+
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial patch fixes a typo in iavf.h.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds zero-copy Tx support for AF_XDP sockets. It implements
the ndo_xsk_async_xmit netdev ndo and performs all the Tx logic from a
NAPI context. This means pulling egress packets from the Tx ring,
placing the frames on the NIC HW descriptor ring and completing sent
frames back to the application via the completion ring.
The regular XDP Tx ring is used for AF_XDP as well. This rationale for
this is as follows: XDP_REDIRECT guarantees mutual exclusion between
different NAPI contexts based on CPU id. In other words, a netdev can
XDP_REDIRECT to another netdev with a different NAPI context, since
the operation is bound to a specific core and each core has its own
hardware ring.
As the AF_XDP Tx action is running in the same NAPI context and using
the same ring, it will also be protected from XDP_REDIRECT actions
with the exact same mechanism.
As with AF_XDP Rx, all AF_XDP Tx specific functions are added to
ixgbe_xsk.c.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: William Tu <u9012063@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prepares for the upcoming zero-copy Tx functionality by
moving common functions used both by the regular path and zero-copy
path.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: William Tu <u9012063@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds zero-copy Rx support for AF_XDP sockets. Instead of
allocating buffers of type MEM_TYPE_PAGE_SHARED, the Rx frames are
allocated as MEM_TYPE_ZERO_COPY when AF_XDP is enabled for a certain
queue.
All AF_XDP specific functions are added to a new file, ixgbe_xsk.c.
Note that when AF_XDP zero-copy is enabled, the XDP action XDP_PASS
will allocate a new buffer and copy the zero-copy frame prior passing
it to the kernel stack.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: William Tu <u9012063@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prepares for the upcoming zero-copy Rx functionality, by
moving/changing linkage of common functions, used both by the regular
path and zero-copy path.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: William Tu <u9012063@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functions for Rx/Tx ring enable/disable. Instead of resetting the
whole device, only the affected ring is disabled or enabled.
This plumbing is used in later commits, when zero-copy AF_XDP support
is introduced.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: William Tu <u9012063@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fix crash when we have restore flow director filters after reset
adapter. In ixgbe_fdir_filter_restore() filter->action is outside of the
rx_ring array, as it has a VF identifier in the upper 32 bits.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
drivers/net/ethernet/intel/i40e/i40e_debugfs.c:136:9: warning: address
of array 'vsi->active_vlans' will always evaluate to 'true'
[-Wpointer-bool-conversion]
vsi->active_vlans ? "<valid>" : "<null>");
~~~~~^~~~~~~~~~~~ ~
./include/linux/device.h:1431:33: note: expanded from macro 'dev_info'
_dev_info(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
1 warning generated.
Given that the statement shows that active_vlans is always valid, just
remove the statement since it's not giving any useful information.
Link: https://github.com/ClangBuiltLinux/linux/issues/82
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clang warns when one enumerated type is converted implicitly to another.
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4214:42: warning:
implicit conversion from enumeration type 'enum i40e_aq_link_speed' to
different enumeration type 'enum virtchnl_link_speed'
[-Wenum-conversion]
pfe.event_data.link_event.link_speed = I40E_LINK_SPEED_40GB;
~ ^~~~~~~~~~~~~~~~~~~~
1 warning generated.
Use the proper enum from virtchnl_link_speed, which has the same value
as I40E_LINK_SPEED_40GB, VIRTCHNL_LINK_SPEED_40GB. This appears to be
missed by commit ff3f4cc267 ("virtchnl: finish conversion to virtchnl
interface").
Link: https://github.com/ClangBuiltLinux/linux/issues/81
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ipsec->tx_tbl[] array has IXGBE_IPSEC_MAX_SA_COUNT elements so the >
should be a >=.
Fixes: 0062e7cc95 ("ixgbevf: add VF IPsec offload code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are no in-tree callers.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have Tx hang when number Tx and XDP queues are more than 64.
In XDP always is MTQC == 0x0 (64TxQs). We need more space for Tx queues.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't be fancy with message lengths, just set lengths to
number of dwords, not bytes.
Fixes: 0062e7cc95 ("ixgbevf: add VF IPsec offload code")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-10-03
This series contains updates to ice and virtchnl.
Yashaswini Raghuram adds a new virtchnl capability flag to support the
exchange of additional supported speeds.
Anirudh adds support for SR-IOV for the ice driver. Added code to
initialize, configure and use mailbox queues for PF and VF
communication. Updated the VSI and queue management to handle both PF
and VF VSI type. Added "Adaptive Virtual Function (AVF)" support for
the ice PF driver by implementing virtchnl commands. Extended the
malicious driver detection logic to include the VF driver as well.
Fixed the queue region size which needs to be log base 2 of the number
of queues in region.
Brett fixes an issue which was causing switch rules to be lost, by
making a call to ice_update_pkt_fwd_rule() with the necessary changes.
Fixed how the PF and VF assigned the ITR index by adding a struct member
itr_idx to be used to dynamically program the correct ITR index.
Dave fixed a potential NULL pointer dereference by adding checks in the
filter handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb_set_tx_maxrate will be called holding rtnl lock,
hence remove all unneeded locks.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version string to 0.7.2-k
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ice_ena/dis_vsi should have a single differentiating
factor to determine if the netdev_ops call is used or a
direct call to ice_vsi_open/close. This is if the netif is
running or not. If netif is running, use ndo_open/ndo_close.
Else, use ice_vsi_open/ice_vsi_close.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This issue came about when looking at the VF function
ice_vc_cfg_irq_map_msg. Currently we are assigning the itr_setting value
to the itr_idx received from the AVF driver, which is not correct and is
not used for the VF flow anyway. Currently the only way we set the ITR
index for both the PF and VF driver is by hard coding ICE_TX_ITR or
ICE_RX_ITR for the ITR index on each q_vector.
To fix this, add the member itr_idx in struct ice_ring_container. This
can then be used to dynamically program the correct ITR index. This change
also affected the PF driver so make the necessary changes there as well.
Also, removed the itr_setting member in struct ice_ring because it is not
being used meaningfully and is going to be removed in a future patch that
includes dynamic ITR.
On another note, this will be useful moving forward if we decide to split
Rx/Tx rings on different q_vectors instead of sharing them as queue pairs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks in the filter handling flow to avoid dereferencing
NULL pointers.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a switch rule is initially created we set the filter action to
ICE_FWD_TO_VSI. The filter action changes to ICE_FWD_TO_VSI_LIST
whenever more than one VSI is subscribed to the same switch rule. When
the switch rule goes from 2 VSIs in the list to 1 VSI we remove and
delete the VSI list rule, but we currently don't update the switch rule
in hardware. This is causing switch rules to be lost, so fix that by
making a call to ice_update_pkt_fwd_rule() with the necessary changes.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When adding a rule, queue region size needs to be provided as log base 2
of the number of queues in region. Fix that.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the existing malicious driver operation detection
logic to cover malicious operations by the VF driver as well.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When PF gets a link status change event, notify the VFs of the same.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
virtchnl is a protocol/interface specification that allows the Intel
"Adaptive Virtual Function (AVF)" driver (iavf.ko) to work with more than
one physical function driver. The AVF driver sends "virtchnl commands"
(control plane only) to the PF driver over mailbox queues and the PF driver
executes these commands and returns a result to the VF, again over mailbox.
This patch adds AVF support for the ice PF driver by implementing the
following virtchnl commands:
VIRTCHNL_OP_VERSION
VIRTCHNL_OP_GET_VF_RESOURCES
VIRTCHNL_OP_RESET_VF
VIRTCHNL_OP_ADD_ETH_ADDR
VIRTCHNL_OP_DEL_ETH_ADDR
VIRTCHNL_OP_CONFIG_VSI_QUEUES
VIRTCHNL_OP_ENABLE_QUEUES
VIRTCHNL_OP_DISABLE_QUEUES
VIRTCHNL_OP_ADD_ETH_ADDR
VIRTCHNL_OP_DEL_ETH_ADDR
VIRTCHNL_OP_CONFIG_VSI_QUEUES
VIRTCHNL_OP_ENABLE_QUEUES
VIRTCHNL_OP_DISABLE_QUEUES
VIRTCHNL_OP_REQUEST_QUEUES
VIRTCHNL_OP_CONFIG_IRQ_MAP
VIRTCHNL_OP_CONFIG_RSS_KEY
VIRTCHNL_OP_CONFIG_RSS_LUT
VIRTCHNL_OP_GET_STATS
VIRTCHNL_OP_ADD_VLAN
VIRTCHNL_OP_DEL_VLAN
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements handlers for the following NDO operations:
.ndo_set_vf_spoofchk
.ndo_set_vf_mac
.ndo_get_vf_config
.ndo_set_vf_trust
.ndo_set_vf_vlan
.ndo_set_vf_link_state
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Post VF initialization, there are a couple of different ways in which a
VF reset can be triggered. One is when the underlying PF itself goes
through a reset and other is via a VFLR interrupt. ice_reset_vf introduced
in this patch handles both these cases.
Also introduced in this patch is a helper function ice_aq_send_msg_to_vf
to send messages to VF over the mailbox queue. The PF uses this to send
reset notifications to VFs.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Until now, all the VSI and queue management code supported only the PF
VSI type (ICE_VSI_PF). Update these flows to handle the VF VSI type
(ICE_VSI_VF) type as well.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements parts of ice_sriov_configure and VF reset flow.
To create virtual functions (VFs), the user sets a value in num_vfs
through sysfs. This results in the kernel calling the handler for
.sriov_configure which is ice_sriov_configure.
VF setup first starts with a VF reset, followed by allocation of the VF
VSI using ice_vf_vsi_setup. Once the VF setup is complete a state bit
ICE_VF_STATE_INIT is set in the vf->states bitmap to indicate that
the VF is ready to go.
Also for VF reset to go into effect, it's necessary to issue a disable
queue command (ice_aqc_opc_dis_txqs). So this patch updates multiple
functions in the disable queue flow to take additional parameters that
distinguish if queues are being disabled due to VF reset.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mailbox queue is a type of control queue that's used for communication
between PF and VF. This patch adds code to initialize, configure and
use mailbox queues.
This patch also adds support to detect and parse SR-IOV capabilities
returned by the hardware.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This affects at least versions 25 and 33, so assume all cards are broken
and just renegotiate by default.
Fixes: 10bc6a6042 ("r8169: fix autoneg issue on resume with RTL8168E")
Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:390:4: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
IEEE_FAUX_SYNC(dev, dcb);
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.h:70:10: note: expanded
from macro 'IEEE_FAUX_SYNC'
CXGB4_DCB_STATE_FW_ALLSYNCED);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Use the equivalent value of the expected type to silence Clang while
resulting in no functional change.
CXGB4_DCB_STATE_FW_ALLSYNCED = CXGB4_DCB_INPUT_FW_ALLSYNCED = 3
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:303:7: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
? CXGB4_DCB_STATE_FW_ALLSYNCED
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:304:7: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
: CXGB4_DCB_STATE_FW_INCOMPLETE);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2 warnings generated.
Use the equivalent value of the expected type to silence Clang while
resulting in no functional change.
CXGB4_DCB_STATE_FW_INCOMPLETE = CXGB4_DCB_INPUT_FW_INCOMPLETE = 2
CXGB4_DCB_STATE_FW_ALLSYNCED = CXGB4_DCB_INPUT_FW_ALLSYNCED = 3
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2734:34: warning:
tentative array definition assumed to have one element
static const struct of_device_id dpaa_match[];
^
1 warning generated.
Turns out that since this driver was introduced in commit 9ad1a37493
("dpaa_eth: add support for DPAA Ethernet"), this declaration has been
unused. Remove it to silence the warning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for inserting and deleting Rx flow classification
rules through ethtool.
We support classification based on some header fields for
flow-types ether, ip4, tcp4, udp4 and sctp4.
Rx queues are core affine, so the action argument effectively
selects on which cpu the matching frame will be processed.
Discarding the frame is also supported.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For firmware versions that support it, configure an Rx flow
classification key at probe time.
Hardware expects all rules in the classification table to share
the same key. So we setup a key containing all supported fields
at driver init and when a user adds classification rules through
ethtool, we will just mask out the unused header fields.
Since the key composition process is the same for flow
classification and hashing, reuse existing code where possible.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the array of supported header fields will be used for
Rx flow classification as well, rename it from "hash_fields" to
the more inclusive "dist_fields".
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Management Complex (MC) firmware initially allowed the
configuration of a single key to be used both for Rx flow hashing
and flow classification. This prevented us from supporting
Rx flow classification through ethtool.
Starting with version 10.7.0, the Management Complex(MC) offers
a new set of APIs for separate configuration of Rx hashing and
classification keys.
Update the Rx flow hashing support to use the new API, if available.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbsmA5AAoJEEg/ir3gV/o+Bg0IAM4qUD878349YufTxlNI3usz
pPyRYLFfh+f3oTjGWxZ4SlAzMsCVnGDWMKFBj33qnJen1YcMxD2DriTIStQfOHkE
EpErxxMa70YFY2VyvD6Gt/Xfw9Q4ZGrp9j4tNnXVBMVT+EDhui/OpHFlpgoLtpLk
A8pxPRkbQNdql4OWOLwVpFJoleB0mJp4+ed+z743z4ectBfY0Iqx6Yyk1TRUzLfB
o/cUV02M33Fi8XjjZ59crPrIc4r0iUcPDcd5+8i2WtOkfbFod9s1Dg4GMNbGpcFn
RPJX9A+XilMPCJNM8YhwcS2JxX8Y2XwUjBDbspx0RHX3HZY22SjuN2i5p1GZnLo=
=pu43
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-10-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-10-01
This pull request includes some fixes to mlx5 driver,
Please pull and let me know if there's any problem.
For -stable v4.11:
"6e0a4a23c59a ('net/mlx5: E-Switch, Fix out of bound access when setting vport rate')"
For -stable v4.18:
"98d6627c372a ('net/mlx5e: Set vlan masks for all offloaded TC rules')"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The incoming skb needs to be reallocated in case the headroom
is not sufficient to adjust the ethernet header. This allocation
needs to be atomic otherwise it results in this splat
[<600601bb>] ___might_sleep+0x185/0x1a3
[<603f6314>] ? _raw_spin_unlock_irqrestore+0x0/0x27
[<60069bb0>] ? __wake_up_common_lock+0x95/0xd1
[<600602b0>] __might_sleep+0xd7/0xe2
[<60065598>] ? enqueue_task_fair+0x112/0x209
[<600eea13>] __kmalloc_track_caller+0x5d/0x124
[<600ee9b6>] ? __kmalloc_track_caller+0x0/0x124
[<602696d5>] __kmalloc_reserve.isra.34+0x30/0x7e
[<603f629b>] ? _raw_spin_lock_irqsave+0x0/0x3d
[<6026b744>] pskb_expand_head+0xbf/0x310
[<6025ca6a>] rmnet_rx_handler+0x7e/0x16b
[<6025c9ec>] ? rmnet_rx_handler+0x0/0x16b
[<6027ad0c>] __netif_receive_skb_core+0x301/0x96f
[<60033c17>] ? set_signals+0x0/0x40
[<6027bbcb>] __netif_receive_skb+0x24/0x8e
Fixes: 74692caf1b ("net: qualcomm: rmnet: Process packets over ethernet")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The incoming skb needs to be reallocated in case the headroom
is not sufficient to add the MAP header. This allocation needs to
be atomic otherwise it results in the following splat
[32805.801456] BUG: sleeping function called from invalid context
[32805.841141] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[32805.904773] task: ffffffd7c5f62280 task.stack: ffffff80464a8000
[32805.910851] pc : ___might_sleep+0x180/0x188
[32805.915143] lr : ___might_sleep+0x180/0x188
[32806.131520] Call trace:
[32806.134041] ___might_sleep+0x180/0x188
[32806.137980] __might_sleep+0x50/0x84
[32806.141653] __kmalloc_track_caller+0x80/0x3bc
[32806.146215] __kmalloc_reserve+0x3c/0x88
[32806.150241] pskb_expand_head+0x74/0x288
[32806.154269] rmnet_egress_handler+0xb0/0x1d8
[32806.162239] rmnet_vnd_start_xmit+0xc8/0x13c
[32806.166627] dev_hard_start_xmit+0x148/0x280
[32806.181181] sch_direct_xmit+0xa4/0x198
[32806.185125] __qdisc_run+0x1f8/0x310
[32806.188803] net_tx_action+0x23c/0x26c
[32806.192655] __do_softirq+0x220/0x408
[32806.196420] do_softirq+0x4c/0x70
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RMNET RX handler was processing invalid packets that were
originally sent on the real device and were looped back via
dev_loopback_xmit(). This was detected using syzkaller.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AON_PM_L2 is normally used to trigger and identify the source of a
wake-up event. Since the RX_SYS clock is no longer turned off, we also
have an interrupt being sent to the SYSTEMPORT INTRL_2_0 controller, and
that interrupt remains active up until the magic packet detector is
disabled which happens much later during the driver resumption.
The race happens if we have a CPU that is entering the SYSTEMPORT
INTRL2_0 handler during resume, and another CPU has managed to clear the
wake-up interrupt during bcm_sysport_resume_from_wol(). In that case, we
have the first CPU stuck in the interrupt handler with an interrupt
cause that has been cleared under its feet, and so we keep returning
IRQ_NONE and we never make any progress.
This was not a problem before because we would always turn off the
RX_SYS clock during WoL, so the SYSTEMPORT INTRL2_0 would also be turned
off as well, thus not latching the interrupt.
The fix is to make sure we do not enable either the MPD or
BRCM_TAG_MATCH interrupts since those are redundant with what the
AON_PM_L2 interrupt controller already processes and they would cause
such a race to occur.
Fixes: bb9051a2b2 ("net: systemport: Add support for WAKE_FILTER")
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After bfcb79fca1 ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When FW floods the driver with control messages try to exit the cmsg
processing loop every now and then to avoid soft lockups. Cmsg
processing is generally very lightweight so 512 seems like a reasonable
budget, which should not be exceeded under normal conditions.
Fixes: 77ece8d5f1 ("nfp: add control vNIC datapath")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-10-02
This series contains updates to ice driver only.
Anirudh expands the use of VSI handles across the rest of the driver,
which includes refactoring the code to correctly use VSI handles. After
a reset, ensure that all configurations for a VSI get re-applied before
moving on to rebuilding the next VSI.
Dave fixed the driver to check the current link state after reset to
ensure that the correct link state of a port is reported. Fixed an
issue where if the driver is unloaded when traffic is in progress,
errors are generated.
Preethi breaks up the IRQ tracker into a software and hardware IRQ
tracker, where the software IRQ tracker tracks only the PF's IRQ
requests and does not play any role in the VF initialization. The
hardware IRQ tracker represents the device's interrupt space and will be
looked up to see if the device has run our of interrupts when a
interrupt has to be allocated in the device for either PF or VF.
Md Fahad adds support for enabling/disabling RSS via ethtool.
Brett aligns the ice_reset_req enum values to the values that the
hardware understands. Also added initial support for dynamic interrupt
moderation in the ice driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a commit 4bcc595ccd ("printk: reinstate KERN_CONT for printing
continuation lines") regression with the `declance' driver, which caused
the adapter identification message to be split between two lines, e.g.:
declance.c: v0.011 by Linux MIPS DECstation task force
tc6: PMAD-AA
, addr = 08:00:2b:1b:2a:6a, irq = 14
tc6: registered as eth0.
Address that properly, by printing identification with a single call,
making the messages now look like:
declance.c: v0.011 by Linux MIPS DECstation task force
tc6: PMAD-AA, addr = 08:00:2b:1b:2a:6a, irq = 14
tc6: registered as eth0.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: 4bcc595ccd ("printk: reinstate KERN_CONT for printing continuation lines")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver support for reading/configuring the 20G link speed via ethtool.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver support for configuring/reading the 20G link speed.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During certain heavy network loads TX could time out
with TX ring dump.
TX is sometimes never restarted after reaching
"tx_stop_threshold" because function "fec_enet_tx_queue"
only tests the first queue.
In addition the TX timeout callback function failed to
recover because it also operated only on the first queue.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is unloaded when traffic is in progress, errors are
generated. Fix this by releasing qvectors and NAPI handler on remove.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there is no support for dynamic interrupt moderation. This
patch adds some initial code to support this. The following changes
were made:
1. Currently we are using multiple members to store the interrupt
granularity (itr_gran_25/50/100/200). This is not necessary because
we can query the device to determine what the interrupt granularity
should be set to, done by a new function ice_get_itr_intrl_gran.
2. Added intrl to ice_q_vector structure to support interrupt rate
limiting.
3. Added the function ice_intrl_usecs_to_reg for converting to a value
in usecs that the device understands.
4. Added call to write to the GLINT_RATE register. Disable intrl by
default for now.
5. Changed rx/tx_itr_setting to itr_setting because having both seems
redundant because a ring is either Tx or Rx.
6. Initialize itr_setting for both Tx/Rx rings in ice_vsi_alloc_rings()
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the ice_reset_req enum values have to be translated into
a different set of values that the hardware understands for the same
reset types. Avoid this translation by aligning ice_reset_req enum
values to the ones that the hardware understands.
Also add and else if block to check for ICE_RESET_EMPR and put a dev_dbg
message in the else case.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements ethtool hook for enabling/disabling
RSS. While disabling RSS, the LUT should be cleared. And
the LUT should be reconfigured while enabling RSS.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For the PF driver, when mapping interrupts to queues, we need to request
IRQs from the kernel and we also have to allocate interrupts from
the device.
Similarly, when the VF driver (iavf.ko) initializes, it requests the kernel
IRQs that it needs but it can't directly allocate interrupts in the device.
Instead, it sends a mailbox message to the ice driver, which then allocates
interrupts in the device on the VF driver's behalf.
Currently both these cases end up having to reserve entries in
pf->irq_tracker but irq_tracker itself is sized based on how many vectors
the PF driver needs. Under the right circumstances, the VF driver can fail
to get entries in irq_tracker, which will result in the VF driver failing
probe.
To fix this, sw_irq_tracker and hw_irq_tracker are introduced. The
sw_irq_tracker tracks only the PF's IRQ request and doesn't play any
role in VF init. hw_irq_tracker represents the device's interrupt space.
When interrupts have to be allocated in the device for either PF or VF,
hw_irq_tracker will be looked up to see if the device has run out of
interrupts.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are currently replaying the link state of a port after a reset, but
it is possible that the link state of a port can change during the reset
process. So check for the current link state of a port during the rebuild
process of a reset.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, switch filters get replayed after reset. In addition to
filters, other VSI attributes (like RSS configuration, Tx scheduler
configuration, etc.) also need to be replayed after reset.
Thus, instead of replaying based on functional blocks (i.e. replay
all filters for all VSIs, followed by RSS configuration replay for
all VSIs, and so on), it makes more sense to have the replay centered
around a VSI. In other words, replay all configurations for a VSI before
moving on to rebuilding the next VSI.
To that effect, this patch introduces a VSI replay framework in a new
function ice_vsi_replay_all. Currently it only replays switch filters,
but it will be expanded in the future to replay additional VSI attributes.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a continuation of the previous patch where VSI
handles are used instead of VSI numbers.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A VSI handle is just a number the driver maintains to uniquely identify
a VSI. A VSI handle is backed by a VSI number in the hardware. When
interacting when the hardware, VSI handles are converted into VSI numbers.
In commit 0f9d5027a7 ("ice: Refactor VSI allocation, deletion and
rebuild flow"), VSI handles were introduced but it was used only
when creating and deleting VSIs. This patch is part one of two patches
that expands the use of VSI handles across the rest of the driver. Also
in this patch, certain parts of the code had to be refactored to correctly
use VSI handles.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In current ABI the size of the messages carrying map elements was
statically defined to at most 16 words of key and 16 words of value
(NFP word is 4 bytes). We should not make this assumption and use
the max key and value sizes from the BPF capability instead.
To make sure old kernels don't get surprised with larger (or smaller)
messages bump the FW ABI version to 3 when key/value size is different
than 16 words.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Some apps may want to have higher MTU on the control vNIC/queue.
Allow them to set the requested MTU at init time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Up until now we only had per-vNIC BPF ABI version capabilities,
which are slightly awkward to use because bulk of the resources
and configuration does not relate to any particular vNIC. Add
a new capability for global ABI version and check the per-vNIC
version are equal to it. Assume the ABI version 2 if no explicit
version capability is present.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When choosing channel amounts and ring sizes, the maximums in the
ibmvnic driver are defined by the virtual i/o server management
partition. Even though they are defined as maximums, the client
driver may in fact successfully request resources that exceed
these limits, which are mostly dependent on a user's hardware
With this in mind, provide an ethtool flag that when enabled will
allow the user to request resources limited by driver-defined
maximums instead of limits defined by the management partition.
The driver will try to honor the user's request but may not allowed
by the management partition. In this case, the driver requests
as close as it can get to the desired amount until it succeeds.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce driver-defined maximums for queue ring sizes. Devices
available for IBM vNIC today will likely not allow this amount,
but this should give us some leeway for future devices that may
support larger ring sizes.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase queue size limit to 16. Devices available for IBM vNIC today
will not allow this amount, but this should give us some leeway for
future devices that may support more RX or TX queues.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the chip-specific hw_start functions set bit TXCFG_AUTO_FIFO
in register TxConfig. The original patch changed the order of some
calls resulting in these changes being overwritten by
rtl_set_tx_config_registers() in rtl_hw_start(). This eventually
resulted in network stalls especially under high load.
Analyzing the chip-specific hw_start functions all chip version from
34, with the exception of version 39, need this bit set.
This patch moves setting this bit to rtl_set_tx_config_registers().
Fixes: 4fd48c4ac0 ("r8169: move common initializations to tp->hw_start")
Reported-by: Ortwin Glück <odi@odi.ch>
Reported-by: David Arendt <admin@prnet.org>
Root-caused-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Tested-by: Tony Atkinson <tatkinson@linux.com>
Tested-by: David Arendt <admin@prnet.org>
Tested-by: Ortwin Glück <odi@odi.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When inserting the TSB, keep track of how many times we had to do it and
if there was a failure in doing so, this helps profile the driver for
possibly incorrect headroom settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During bcm_sysport_insert_tsb() make sure we differentiate a SKB
headroom re-allocation failure from the normal swap and replace path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can turn on the RX/TX checksum offloads by default and make sure that
those are properly reflected back to e.g: stacked devices such as VLAN
or DSA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver resume and open, the HW may have lost its context/state,
utilize bcm_sysport_set_features() to make sure we do restore the
correct set of features that were previously configured.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally enabling TX and RX checksum offloads,
refactor bcm_sysport_set_features() a bit such that
__netdev_update_features() during register_netdev() can make sure that
features are correctly programmed during network device registration.
Since we can now be called during register_netdev() with clocks gated,
we need to temporarily turn them on/off in order to have a successful
register programming.
We also move the CRC forward setting read into
bcm_sysport_set_features() since priv->crc_fwd matters while turning on
RX checksum offload, that way we are guaranteed they are in sync in case
we ever add support for NETIF_F_RXFCS at some point in the future.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds switch for flow director with ethtool command
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all flow director rules when unload hns3 driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reset, remove all entries in TCAM block, and keep flow
director rules list. After finishing reset, restore all entries.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for querying rule number and rule details
by ethtool commands.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for add and delete rule by ethtool commands.
HNS3 driver supports several flow types, include ETHER_FLOW,
IP_USER_FLOW, TCP_V4_FLOW, UDP_V4_FLOW, SCTP_V4_FLOW, IPV6_USER_FLOW,
TCP_V6_FLOW, UDP_V6_FLOW and SCTP_V6_FLOW.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each flow director rule consists of input key and action. The input key
is the condition for matching, includes tuples of L2/L3/L4 header.
Action is the behaviour when a packet matches with the input key, such
as drop the packet, or forward to a specified queue.
The input key is stored in the tcam blocks, Each bit of input key can
be masked.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow director is a new feature supported by hardware with revision 0x21.
This patch adds flow direcor initialization for each PF. It queries flow
director mode and tcam resource from firmware, selects tuples used for
input key.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan