The function mmc_omap_report_irq uses raw printks and the actual output
was disabled by a static variable. Make the function use dev_vdbg macro
and use it under the standard CONFIG_MMC_DEBUG flag.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Get rid of some unnecessary includes in the driver and
a few unused variables.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ext_csd exported through debugfs is printed in reverse order (from
byte 511 to 0), which causes confusion.
Fix the for loop to print ext_csd in natural order.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
HPI can be issued only in programming state to bring the card to
transfer state. If the card is already in transfer state, doing
a HPI is redundant.
Fix this by adding transfer state to the list of exceptions to
doing HPI and return without error.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Without reset, SD controller may stay in disable mode, SD card can't
be detected when resume from power saving mode.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc core suspend and resume functions had already called sdh_set_ios
with proper flags.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In BF60x RSI controller:
1) MMR read/write width differs.
2) PWR and CTL MMRs are merged to together.
3) ROD and PD_DAT3 bit masks are obsolete.
4) New RSI block size MMR is defined.
5) The definition of DMA descriptor set size is changed.
6) set_ios should powers up controller in 2 steps.
In addition, this patch cleans up the spin locks.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
1/ If regulator_get fails, return an error. This is important if
it failed with EPROBE_DEFER, as the probe needs to be deferred.
2/ Don't set .set_power until the regulator has been found, or
the deferred probe will not bother calling omap_hsmmc_reg_get().
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add missing usb_free_urb on failure path after usb_alloc_urb.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@km exists@
local idexpression e;
expression e1,e2,e3;
type T,T1;
identifier f;
@@
* e = usb_alloc_urb(...)
... when any
when != e = e1
when != e1 = (T)e
when != e1(...,(T)e,...)
when != &e->f
if(...) { ... when != e2(...,(T1)e,...)
when != e3 = e
when forall
(
return <+...e...+>;
|
* return ...;
) }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds device tree support and binding documentation for
sdhci-dove.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The vmmc regulator should not rely on the platform code to enable it.
Expliciitly enable and disable the regulator inside the driver.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some systems the host controller does not support vccq
signaling. This is supplied by a dedicated regulator (vqmmc).
Add support for this regulator.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The register of eSDHC Host Controller Capabilities is not compatible with
standard SDHC register, and eSDHC cannot support End Attribute in NOP ADMA
descriptor. With this patch eSDHC can works in ADMA mode and performance
can be improved.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Pan Jiafei <Jiafei.Pan@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
After commit 26b88520b8 ("mmc:
omap_hsmmc: remove private DMA API implementation"), the Nokia N800
here stopped booting:
[ 2.086181] Waiting for root device /dev/mmcblk0p1...
[ 2.324066] Unhandled fault: imprecise external abort (0x406) at 0x00000000
[ 2.331451] Internal error: : 406 [#1] ARM
[ 2.335784] Modules linked in:
[ 2.339050] CPU: 0 Not tainted (3.6.0-rc3 #60)
[ 2.344146] PC is at default_idle+0x28/0x30
[ 2.348602] LR is at trace_hardirqs_on_caller+0x15c/0x1b0
...
This turned out to be due to memory corruption caused by long-broken
PIO code in drivers/mmc/host/omap.c. (Previously, this driver had
been using DMA; but the above commit caused the MMC driver to fall
back to PIO mode with an unmodified Kconfig.)
The PIO code, added with the rest of the driver in commit
730c9b7e66 ("[MMC] Add OMAP MMC host
driver"), confused bytes with 16-bit words. This bug caused memory
located after the PIO transfer buffer to be corrupted with transfers
larger than 32 bytes. The driver also did not increment the buffer
pointer after the transfer occurred. This bug resulted in data
corruption during any transfer larger than 64 bytes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For several MoviNAND eMMC parts, there are known issues with secure
erase and secure trim. For these specific MoviNAND devices, we skip
these operations.
Specifically, there is a bug in the eMMC firmware that causes
unrecoverable corruption when the MMC is erased with MMC_CAP_ERASE
enabled.
References:
http://forum.xda-developers.com/showthread.php?t=1644364https://plus.google.com/111398485184813224730/posts/21pTYfTsCkB#111398485184813224730/posts/21pTYfTsCkB
Signed-off-by: Ian Chen <ian.cy.chen@samsung.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@vger.kernel.org> [3.0+]
Signed-off-by: Chris Ball <cjb@laptop.org>
The documentation for the dw_mmc part says that the low power
mode should normally only be set for MMC and SD memory and should
be turned off for SDIO cards that need interrupts detected.
The best place I could find to do this is when the SDIO interrupt
was first enabled. I rely on the fact that dw_mci_setup_bus()
will be called when it's time to reenable.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Data transfer will be continued until all the bytes are transmitted,
even if data crc error occurs during a multiple-block data transfer.
This means RXDR/TXDR interrupts will occurs until data transfer is
terminated. Early setting of host->sg to NULL prevents going into
xxx_data_pio functions, hence permanent unhandled RXDR/TXDR interrupts
occurs. And checking error interrupt status in the xxx_data_pio functions
is no need because dw_mci_interrupt does do the same. This patch also
removes it.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Datasheet of SYNOPSYS mentions that DTO(Data Transfer Over) interrupt
will be raised even if some error interrupts, however it is actually
found that DTO does not occur. SYNOPSYS has confirmed this issue.
Current implementation defers the call of tasklet_schedule until DTO
when the error interrupts is happened. This patch fixes error handling.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
RINTSTS status includes masked interrupts as well as unmasked.
data_status and cmd_status are set by value of RINTSTS in interrupt handler
and tasklet finally uses it to decide whether error is happened or not.
In addition, MINTSTS status is used for setting data_status in PIO.
Masked error interrupt will not be handled and that status can be considered
non-error case.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed By: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even if the datasheet says that the not busy flag has to be used only
for write operations, it's false except for version lesser than v2xx.
Not waiting on the not busy flag for read operations can cause the
controller to hang-up during the initialization of some SD cards
with DMA after the first CMD6 -- the next command is sent too early.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.5, 3.6]
Signed-off-by: Chris Ball <cjb@laptop.org>
Since commit 30832ab56 ("mmc: sdhci: Always pass clock request value
zero to set_clock host op") was merged, esdhc_set_clock starts hitting
"if (clock == 0)" where ESDHC_SYSTEM_CONTROL has been operated. This
causes SDHCI card-detection function being broken. Fix the regression
by moving "if (clock == 0)" above ESDHC_SYSTEM_CONTROL operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Descriptor array structure has been moved into blackfin dma.h head file.
This patch fix below error:
drivers/mmc/host/bfin_sdh.c:52:8: error: redefinition of 'struct
dma_desc_array'
make[4]: *** [drivers/mmc/host/bfin_sdh.o] Error 1
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull OLPC platform updates from Andres Salomon:
"These move the OLPC Embedded Controller driver out of
arch/x86/platform and into drivers/platform/olpc.
OLPC machines are now ARM-based (which means lots of x86 and ARM
changes), but are typically pretty self-contained.. so it makes more
sense to go through a separate OLPC tree after getting the appropriate
review/ACKs."
* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
x86: OLPC: move s/r-related EC cmds to EC driver
Platform: OLPC: move global variables into priv struct
Platform: OLPC: move debugfs support from x86 EC driver
x86: OLPC: switch over to using new EC driver on x86
Platform: OLPC: add a suspended flag to the EC driver
Platform: OLPC: turn EC driver into a platform_driver
Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
drivers: OLPC: update various drivers to include olpc-ec.h
Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver
This branch contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the branch
into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xb8w
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
"This contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the
branch into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: Kirkwood: Replace mrvl with marvell
ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
ARM: Kirkwood: Describe Dreamplug LEDs in DT.
ARM: Kirkwood: Describe iConnects LEDs in DT.
ARM: Kirkwood: Describe iConnects temperature sensor in DT.
ARM: Kirkwood: Describe IB62x0 LEDs in DT.
ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
ARM: Kirkwood: Use DT to configure SATA device.
ARM: kirkwood: use devicetree for SPI on dreamplug
ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
ARM: Kirkwood: Add basic device tree support for QNAP TS219.
ATA: sata_mv: Add device tree support
ARM: Orion: DTify the watchdog timer.
ARM: Orion: Add arch support needed for I2C via DT.
ARM: kirkwood: use devicetree for orion-spi
...
Conflicts:
drivers/watchdog/orion_wdt.c
Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree, but
didn't go in because the pull request ended up rejected. So it just got
merged, and we got this staged branch that enables the coupled cpuidle
code on OMAP.
With a stable git workflow from the other maintainer we could have staged
this earlier, but that wasn't the case so we have had to merge it late.
The alternative is to hold it off until 3.7 but given that the code is
well-isolated to OMAP and they are eager to see it go in, I didn't push
back hard in that direction.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Wp41
-----END PGP SIGNATURE-----
Merge tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
"Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
but didn't go in because the pull request ended up rejected. So it
just got merged, and we got this staged branch that enables the
coupled cpuidle code on OMAP.
With a stable git workflow from the other maintainer we could have
staged this earlier, but that wasn't the case so we have had to merge
it late.
The alternative is to hold it off until 3.7 but given that the code is
well-isolated to OMAP and they are eager to see it go in, I didn't
push back hard in that direction."
* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP4: CPUidle: Open broadcast clock-event device.
ARM: OMAP4: CPUidle: add synchronization for coupled idle states
ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus
A few fixes for merge window fallout, and a bugfix for timer resume
on PRIMA2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BkSN
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for merge window fallout, and a bugfix for timer resume on
PRIMA2."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mmp: add missing irqs.h
arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
ARM: mxc: Include missing irqs.h header
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlAaIN8ACgkQGkmNcg7/o7gpMgCgtmCJeUrSCc/eVKGy5ik1BPnC
3DAAoLdqCJflwx4mrN48kkXQj9SA4Xko
=Y6yl
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
sh: explicitly include sh_dma.h in setup-sh7722.c
sh: ecovec: care CN5 VBUS if USB host mode
sh: sh7724: fixup renesas_usbhs clock settings
sh: intc: initial irqdomain support.
sh: pfc: Fix up init ordering mess.
serial: sh-sci: fix compilation breakage, when DMA is enabled
dmaengine: shdma: restore partial transfer calculation
sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
sh: Fix up recursive fault in oops with unset TTB.
sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
sh: select the fixed regulator driver on several boards
sh: ecovec: switch MMC power control to regulators
sh: add fixed voltage regulators to se7724
sh: add fixed voltage regulators to sdk7786
sh: add fixed voltage regulators to rsk
sh: add fixed voltage regulators to migor
sh: add fixed voltage regulators to kfr2r09
sh: add fixed voltage regulators to ap325rxa
sh: add fixed voltage regulators to sh7757lcr
sh: add fixed voltage regulators to sh2007
...
This contains a few patches that depend on
plugging changes in the block layer so needs to wait
for those.
It also contains a Kconfig fix for the new RAID10 support
in dm-raid.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ovN2
-----END PGP SIGNATURE-----
Merge tag 'md-3.6' of git://neil.brown.name/md
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
Pull two ceph fixes from Sage Weil:
"The first patch fixes up the old crufty open intent code to use the
atomic_open stuff properly, and the second fixes a possible null deref
and memory leak with the crypto keys."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: fix crypto key null deref, memory leak
ceph: simplify+fix atomic_open
eCryptfs mount options do not
- Cleanups in the messaging code
- Better handling of empty files in the lower filesystem to improve usability.
Failed file creations are now cleaned up and empty lower files are converted
into eCryptfs during open().
- The write-through cache changes are being reverted due to bugs that are not
easy to fix. Stability outweighs the performance enhancements here.
- Improvement to the mount code to catch unsupported ciphers specified in the
mount options
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4vDd
-----END PGP SIGNATURE-----
Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
- Fixes a bug when the lower filesystem mount options include 'acl',
but the eCryptfs mount options do not
- Cleanups in the messaging code
- Better handling of empty files in the lower filesystem to improve
usability. Failed file creations are now cleaned up and empty lower
files are converted into eCryptfs during open().
- The write-through cache changes are being reverted due to bugs that
are not easy to fix. Stability outweighs the performance
enhancements here.
- Improvement to the mount code to catch unsupported ciphers specified
in the mount options
* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: check for eCryptfs cipher support at mount
eCryptfs: Revert to a writethrough cache model
eCryptfs: Initialize empty lower files when opening them
eCryptfs: Unlink lower inode when ecryptfs_create() fails
eCryptfs: Make all miscdev functions use daemon ptr in file private_data
eCryptfs: Remove unused messaging declarations and function
eCryptfs: Copy up POSIX ACL and read-only flags from lower mount
Pull CIFS update from Steve French:
"Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.
I am holding up a few more days on merging the remainder of the
SMB2/SMB2.1 enablement although it is nearing review completion, in
order to address some review comments from Jeff Layton on a few of the
subsequent SMB2 patches, and also to debug an unrelated cifs problem
that Pavel discovered."
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Add SMB2 support for rmdir
CIFS: Move rmdir code to ops struct
CIFS: Add SMB2 support for mkdir operation
CIFS: Separate protocol specific part from mkdir
CIFS: Simplify cifs_mkdir call
Borislav Petkov reports that the new warning added in commit
88fdf75d1b ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.
The call trace looks like this:
x86_64_start_kernel ->
x86_64_start_reservations ->
start_kernel ->
setup_arch ->
paging_init ->
zone_sizes_init ->
free_area_init_nodes ->
free_area_init_node
and (with the warning replaced by debug output), Borislav sees
On node 0 totalpages: 4193848
DMA zone: 64 pages used for memmap
DMA zone: 6 pages reserved
DMA zone: 3890 pages, LIFO batch:0
DMA32 zone: 16320 pages used for memmap
DMA32 zone: 798464 pages, LIFO batch:31
Normal zone: 52736 pages used for memmap
Normal zone: 3322368 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 4423680 <----
On node 1 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 8617984 <----
On node 2 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 12812288 <----
On node 3 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
so remove the bogus warning for now to avoid annoying people. Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/arm/mach-mmp/gplugd.c:195:13: error: ‘MMP_NR_IRQS’ undeclared here
(not in a function)
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1
Include <mach/irqs.h> to fix this issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The only way to write LATCHED registers to write LATCH_BIT to LATCH register,
that will latch COUNTER into LATCHED.e.g.
writel_relaxed(SIRFSOC_TIMER_LATCH_BIT, sirfsoc_timer_base +
SIRFSOC_TIMER_LATCH);
Writing values to LATCHED registers directly is useless at all.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Avoid crashing if the crypto key payload was NULL, as when it was not correctly
allocated and initialized. Also, avoid leaking it.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
The initial ->atomic_open op was carried over from the old intent code,
which was incomplete and didn't really work. Replace it with a fresh
method. In particular:
* always attempt to do an atomic open+lookup, both for the create case
and for lookups of existing files.
* fix symlink handling by returning 1 to the VFS so that we can follow
the link to its destination. This fixes a longstanding ceph bug (#2392).
Signed-off-by: Sage Weil <sage@inktank.com>
setup-sh7722.c defines several objects, whose types are defined in
sh_dma.h, so, it has to be included explicitly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pull MIPS updates from Ralf Baechle:
"The lion share of this pull request are fixes for clk-related breakage
caused by other changes during this merge window. For some platforms
the fix was as simple as selecting HAVE_CLK, for others like the
Loongson 2 significant restructuring was required.
The remainder are changes required to get the Lantiq code to work
again."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Loongson 2: Sort out clock managment.
MIPS: Loongson 1: more clk support and add select HAVE_CLK
MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: Lantiq: Platform specific CLK fixup
MIPS: Lantiq: Add device_tree_init function
MIPS: Lantiq: Fix interface clock and PCI control register offset
Pull UML fixes from Richard Weinberger:
"This patch set contains mostly fixes and cleanups. The UML tty driver
uses now tty_port and is no longer broken like hell :-)"
* 'for-linus-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Add arch/x86/um to MAINTAINERS
um: pass siginfo to guest process
um: fix ubd_file_size for read-only files
um: pull interrupt_end() into userspace()
um: split syscall_trace(), pass pt_regs to it
um: switch UPT_SET_RETURN_VALUE and regs_return_value to pt_regs
um: set BLK_CGROUP=y in defconfig
um: remove count_lock
um: fully use tty_port
um: Remove dead code
um: remove line_ioctl()
TTY: um/line, use tty from tty_port
TTY: um/line, add tty_port
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
Pull ARM audit/signal updates from Russell King:
"ARM audit/signal handling updates from Al and Will. This improves on
the work Viro did last merge window, and sorts out some of the issues
found with that work."
* 'audit' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7475/1: sys_trace: allow all syscall arguments to be updated via ptrace
ARM: 7474/1: get rid of TIF_SYSCALL_RESTARTSYS
ARM: 7473/1: deal with handlerless restarts without leaving the kernel
ARM: 7472/1: pull all work_pending logics into C function
ARM: 7471/1: Revert "7442/1: Revert "remove unused restart trampoline""
ARM: 7470/1: Revert "7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK""
Venkatraman S