R6xx+ cards need to use the 3D engine to blit data which requires
quite a bit of hw state setup. Rather than pull the whole 3D driver
(which normally generates the 3D state) into the DRM, we opt to use
statically generated state tables. The regsiter state and shaders
were hand generated to support blitting functionality. See the 3D
driver or documentation for descriptions of the registers and
shader instructions.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We still have many magic numbers in HDMI/audio to define
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Older GPUs are little different, HDMI blocks are not hard-wired, but routable.
We should just find some free HDMI block and route it to choosen encoder. In
case of RS6x0 there is only one HDMI block, we don't enable HDMI on RS6x00 yet
however.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We almost always used first HDMI block for first encoder and second for sencod.
Exception was KLDSCP_LVTMA. Analyzing code picking DIG encoder shows the same
behaviour. It shows HDMI block are related to DIGs, which relation we now use.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We already know same offsets are used for different encoders/transmitters, so
just numeric them instead naming incorrectly. Additionaly we found additional
registers needed for RV770+
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixing the i2c prescale in the last patch
gets it working on r1xx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
use the i2c pads to drive SDA
Possible fix for fdo bug 26430
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on ddx patch by Andrzej Hajda.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Adjust modeset ordering to fix spread spectrum.
The spread spectrum command table relies on the
crtc routing to already be set in order to work
properly on some asics.
Should fix fdo bug 25741.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The bios has alternate pll output limits for LCD panels.
If available, use these for pll divider calculations.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The atom spread spectrum table does not always
disable ss. Explicitly disable it and then use
the atom table to enable later if needed (currently
only used for LVDS).
Fixes display issues on some systems.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In somecase the atombios code might lead to infinite loop because
the GPU is in broken state, this patch track the jump history and
will abort atombios execution if we are stuck executing the same
jump for more than 1sec. Note that otherwise in some case we might
enter an infinite loop in the kernel context which is bad.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (151 commits)
vga_switcheroo: disable default y by new rules.
drm/nouveau: fix *staging* driver build with switcheroo off.
drm/radeon: fix typo in Makefile
vga_switcheroo: fix build on platforms with no ACPI
drm/radeon: Fix printf type warning in 64bit system.
drm/radeon/kms: bump the KMS version number for square tiling support.
vga_switcheroo: initial implementation (v15)
drm/radeon/kms: do not disable audio engine twice
Revert "drm/radeon/kms: disable HDMI audio for now on rv710/rv730"
drm/radeon/kms: do not preset audio stuff and start timer when not using audio
drm/radeon: r100/r200 ums: block ability for userspace app to trash 0 page and beyond
drm/ttm: fix function prototype to match implementation
drm/radeon: use ALIGN instead of open coding it
drm/radeon/kms: initialize set_surface_reg reg for rs600 asic
drm/i915: Use a dmi quirk to skip a broken SDVO TV output.
drm/i915: enable/disable LVDS port at DPMS time
drm/i915: check for multiple write domains in pin_and_relocate
drm/i915: clean-up i915_gem_flush_gpu_write_domain
drm/i915: reuse i915_gpu_idle helper
drm/i915: ensure lru ordering of fence_list
...
Fixed trivial conflicts in drivers/gpu/vga/Kconfig
radeon was always including the atpx code unnecessarily, also core
switcheroo was including acpi headers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Type of iterator was promoted to unsigned long in 64bit systems.
*header is small structure so it is alwas safe to cast return value
of sizeof operator to int.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.
4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia - - use _DSM ACPI method.
TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.
v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.
v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.
v4: ATPX msg handling using buffers - should work on more machines
v5: rearchitect after more mjg59 discussion - move ATPX handling to
radeon driver.
v6: add file headers + initial nouveau bits (to be filled out).
v7: merge delayed switcher code.
v8: avoid suspend/resume of gpu that is off
v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling
v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv
v11: fix bug in resuming Intel for 2nd time.
v12: start fixing up nvidia code blindly.
v13: blindly guess at finishing nvidia code
v14: remove radeon audio hacks - fix up intel resume more like upstream
v15: clean up printks + remove unnecessary igd/dis pointers
mount debugfs
/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
+ 2 cards.
DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use
Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit "disabled" audio on RV710 and RV740 only, leaving RV770 and RV730.
The order is: CHIP_RV770 < CHIP_RV730 < CHIP_RV710 < CHIP_RV740.
It is not needed anway, as we do not even try to enable audio on RV770 and
newer. We call initializing function in r600.c only, not in rv770.c.
If there is something causing green tinges, it's HDMI mode setting for encoder
and I will try to debug that.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-testing' of /ssd/git/drm-radeon-next:
drm/radeon: r100/r200 ums: block ability for userspace app to trash 0 page and beyond
drm/ttm: fix function prototype to match implementation
drm/radeon: use ALIGN instead of open coding it
drm/radeon/kms: initialize set_surface_reg reg for rs600 asic
radeon's have a special ability to passthrough writes in their internal
memory space directly to PCI, this ability means that if some of the internal
surfaces like the depth buffer point at 0x0, any writes to these will
go directly to RAM at 0x0 via PCI busmastering.
Now mesa used to always emit clears after emitting state, since the
radeon mesa driver was refactored a year or more ago, it was found it
could generate a clear request without ever sending any setup state to the
card. So the clear would attempt to clear the depth buffer at 0x0, which
would overwrite main memory at this point. fs corruption ensues.
Also once one app did this correctly, it would never get set back to 0
making this messy to reproduce.
The kernel should block this from happening as mesa runs without privs,
though it does require the user be connected to the current running X session.
This patch implements a check to make sure the depth offset has been set
before a depth clear occurs and if it finds one it prints a warning and
ignores the depth clear request. There is also a mesa fix to avoid sending
the badness going into mesa.
This only affects r100/r200 GPUs in user modesetting mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 asic was missing set_surface_reg callback leading to
oops.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
The whole attribute table is valid for
shr/shl ops.
Fixes fdo bug 26668
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
- add support for pre-avivo chips
- add support for fixed post/ref dividers
- add support for non-fractional fb dividers
By default avivo chips use the new algo and
pre-avivo chips use the old algo. Use the "new_pll"
module option to toggle between them.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch properly set visible VRAM and enforce any pinned buffer
to be into visible VRAM. We might later add a flag to release this
constraint for some newer hw more clever than previous.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
AtomBIOS tables on non-mobility GPU do not contain POWERSAVE/BATTERY.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We kept pointers to requested and current clock modes in every power state.
That was useless, more /global/ pointers in power struct are enough.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- updated swizzle modes for backend map setup
- fix programming of a few gfx regs
- properly handle pipe/backend setup on LE cards
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Version 2 of memory controller did break the initialization for
R3XX/R4XX hardware. This patch fix it.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds a check on avivo chips to see if we are in the VBL
region for the active crtcs when we trigger the engine change.
I appear to have glitches locally on pm transistion (not sure all
fixes are in yet) and this at least seems to be correct here,
maybe others can test on systems with no glitches.
Allocation of single large block of memory may fail under memory
presure. drm_buffer object can hold one large block of data in
multiple independ pages which preents alloation failures.
This patch converts all access to command stream to use drm_buffer
interface. All direct access to array has to go tough drm_buffer
functions to get correct pointer.
Outputting the command stream to ring buffer needs to be awear of
the split nature of drm_buffer. The output operation requires the
new OUT_RING_DRM_BUFFER.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This lets UMS userspace know the rv740 fix is in. For KMS we can
consider the kernel release to be the v2.0.0 release so we don't need the
bump there.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If at IB free time fence wasn't emited that means the IB wasn't
scheduled because an error occured somewhere, thus we can free
then fence and mark the IB as free.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just compare the i2c id since the i2c structs
may be slighly different.
Fixes fdo bug 26616.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 board lists DVI port as HDMI.
Fixes fdo bug 26605
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previous code did associate fence to bo before the fence was emited
and it also didn't lock protected access to ttm sync_obj member.
Both of this flaw leads to possible race between different code
path. This patch fix this by associating fence only once the fence
is emitted and properly lock protect access to sync_obj member of
ttm.
Fix:
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely similar others bugs
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is 3 different distinct states for an indirect buffer (IB) :
1- free with no fence
2- free with a fence
3- non free (fence doesn't matter)
Previous code mixed case 2 & 3 in a single one leading to possible
catastrophique failure. This patch rework the handling and properly
separate each case. So when you get ib we set the ib as non free and
fence status doesn't matter. Fence become active (ie has a meaning
for the ib code) once the ib is scheduled or free. This patch also
get rid of the alloc bitmap as it was overkill, we know go through
IB pool list like in a ring buffer as the oldest IB is the first
one the will be free.
Fix :
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely other bugs.
V2 remove the scheduled list, it's useless now, fix free ib scanning
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For usec delays use udelay instead of scheduling, this should
allow reclocking to happen faster. This also was the cause
of reported 33s delays at bootup on certain systems.
fixes: freedesktop.org bug 25506
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Get rid of _location and use _start/_end also simplify the
computation of vram_start|end & gtt_start|end. For R1XX-R2XX
we place VRAM at the same address of PCI aperture, those GPU
shouldn't have much memory and seems to behave better when
setup that way. For R3XX and newer we place VRAM at 0. For
R6XX-R7XX AGP we place VRAM before or after AGP aperture this
might limit to limit the VRAM size but it's very unlikely.
For IGP we don't change the VRAM placement.
Tested on (compiz,quake3,suspend/resume):
PCI/PCIE:RV280,R420,RV515,RV570,RV610,RV710
AGP:RV100,RV280,R420,RV350,RV620(RPB*),RV730
IGP:RS480(RPB*),RS690,RS780(RPB*),RS880
RPB: resume previously broken
V2 correct commit message to reflect more accurately the bug
and move VRAM placement to 0 for most of the GPU to avoid
limiting VRAM.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r200 cards have dma engine which can be used to tranfer data
between vram and system memory.
r300 dma engine registers match r200 dma engine. Enabling
dma copy for r200 is simple as hooking r200 asic to already
existing function r300_copy_dma.
Rename r300_dma_copy to r200_dma_copyto reflect that supports
starts from r200 cards.
v2: Created a new asic object for r200 cards.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Setting global asic structure to point to different function
would cause problem in system where is multiple r300 cards
with different bus type.
r300_asic_pcie is just copy from r300_asic with gart tlb
functions replaced with pcie versions.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r6xx/r7xx use the rs600 variant. This old one just
confuses things.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We should stop audio-state-reading timer before we turn off engine
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/r600_cs.c: In function ‘r600_cs_track_check’:
drivers/gpu/drm/radeon/r600_cs.c:166: warning: ‘bpe’ may be used uninitialized in this function
drivers/gpu/drm/radeon/r600_cs.c:166: note: ‘bpe’ was declared here
drivers/gpu/drm/radeon/r600_cs.c: In function ‘r600_cs_parse’:
drivers/gpu/drm/radeon/r600_cs.c:938: warning: ‘bpe’ may be used uninitialized in this function
drivers/gpu/drm/radeon/r600_cs.c:938: note: ‘bpe’ was declared here
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previous code did associate fence to bo before the fence was emited
and it also didn't lock protected access to ttm sync_obj member.
Both of this flaw leads to possible race between different code
path. This patch fix this by associating fence only once the fence
is emitted and properly lock protect access to sync_obj member of
ttm.
Fix:
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely similar others bugs
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is 3 different distinct states for an indirect buffer (IB) :
1- free with no fence
2- free with a fence
3- non free (fence doesn't matter)
Previous code mixed case 2 & 3 in a single one leading to possible
catastrophique failure. This patch rework the handling and properly
separate each case. So when you get ib we set the ib as non free and
fence status doesn't matter. Fence become active (ie has a meaning
for the ib code) once the ib is scheduled or free. This patch also
get rid of the alloc bitmap as it was overkill, we know go through
IB pool list like in a ring buffer as the oldest IB is the first
one the will be free.
Fix :
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely other bugs.
V2 remove the scheduled list, it's useless now, fix free ib scanning
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In testing I've never seen it go past 1 retry anyways but better
safe than sorry.
Reported by Droste on irc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Noticed on a DEC Alpha.
Start up into console mode caused 15 unaligned accesses, and starting X
caused another 48.
Signed-off-by: Matt Turner <mattst88@gmail.com>
CC: Jerome Glisse <jglisse@redhat.com>
CC: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is partial revert of commit 9404c9c392d5 ("Fix misspelling of "should"
and "shouldn't" in comments"). According to Dave Airlie:
"Can we drop any cleanups to atombios.h? This file comes from
AMD and we normally drop it into place, so they just get overwritten
next time."
Reported-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
radeon_cs kfree the tracker structure but for r6xx/r7xx we want
to kfree it inside the parse function because we share it with
the UMS code path. Set tracker to NULL after freeing it will
avoid double free.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this uses a new entrypoint to invalidate gart entries instead of using 0.
Changed to rather than pointing to 0 address point empty entry to dummy
page. This might help to avoid hard lockup if for some wrong
reasons GPU try to access unmapped GART entry.
I'm not 100% sure this is going to work, we probably need to allocate
a dummy page and point all the GTT entries at it similiar to what AGP does.
but we can test this first I suppose.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's happened time and time again (most recently with the support for EDID
hardcoded in the BIOS ROM) that new code didn't check for rdev->bios being
non-NULL before triggering dereferences of it. This would result in an
oops/panic on setups with no BIOS ROM. Hopefully this central test will be
more robust.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch add cs checker to r600/r700 hw. Command stream checking
will rewrite some of the cs value in order to restrict GPU access
to BO size. This doesn't break old userspace but just enforce safe
value. It should break any things that was using the r600/r700 cs
ioctl to do forbidden things (malicious software), though we are
not aware of such things.
Here is the list of thing we check :
- enforcing resource size
- enforcing color buffer slice tile max, will restrict cb access
- enforcing db buffer slice tile max, will restrict db access
We don't check for shader bigger than the BO in which they are
supposed to be, such use would lead to GPU lockup and is harmless
from security POV, as far as we can tell (note that even checking
for this wouldn't prevent someone to write bogus shader that lead
to lockup).
This patch has received as much testing as humanly possible with
old userspace to check that it didn't break such configuration.
However not all the applications out there were tested, thus it
might broke some odd, rare applications.
[airlied: fix rules for cs checker for parallel builds]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Mostly obvious simplifications.
The i915 pread/pwrite ioctls, intel_overlay_put_image and
nouveau_gem_new were incorrectly using the locked versions
without locking: this is also fixed in this patch.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-linus' of ../drm-next:
drm/radeon/kms: retry auxch on 0x20 timeout value.
drm/radeon: Skip dma copy test in benchmark if card doesn't have dma engine.
drm/radeon/kms: fix screen clearing before fbcon.
drm/radeon/kms: add quirk for VGA without DDC on rv730 XFX card.
drm/radeon/kms: don't crash if no DDC bus on VGA/DVI connector.
drm/radeon/kms: change Kconfig text to reflect the new option.
drm/radeon/kms: suspend and resume audio stuff
ATOM appears to return 0x20 which seems to mean some sort of timeout.
retry the transaction up to 10 times before failing, this
makes DP->VGA convertor we bought work at least a bit more predictably.
Signed-off-by: Dave Airlie <airlied@redhat.com>
original evergreen patches we against a kernel tree
without my radeon i2c algo changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix a typo in crtc offset setup that set the crtc
instances wrong for all crtcs except the first.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pre-pcie chips seem to use the reference clock
rather than the sclk.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_copy_dma is only available for r200 or newer cards.
Call to radeon_copy_dma would result to NULL pointer
dereference if benchmarking asic without dma engine.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This memset_io was added to debug something way back and got
left behind, memset the fb to black so the borders don't be all white.
Signed-off-by: Dave Airlie <airlied@redhat.com>
machine is compatible is an OF-specific call. It should have
the of_ prefix to protect the global namespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
This adds initial Evergreen KMS support, it doesn't include
any acceleration features or interrupt handling yet.
Major changes are DCE4 handling for PLLs for the > 2 crtcs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This merges ugly whitespace we want to keep for consistency
along with the latest upstream changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add an utilities function radeon_ib_bogus_add which will
save an ib into a list of ib which can then be dumped using
debugfs. Once dumped the ib is removed from the list. This
should allow to save & capute ib for further debugging.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This already simplifies code significally and makes it maintaible
in case of adding memory reclocking plus voltage changing in future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
we need a constant sclk for i2c prescale. Also,
get the current sclk when calculating prescale rather
than using the default sclk.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- only r4xx/r5xx/rs6xx/rs740 have clock gating atom table,
so disable it on r6xx. it's already disabled on r7xx
- check to make sure the clock_gating hook exists before
calling it. This avoids a segfault on asics without
that function.
- remove unused static power management function.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The idea is to flag a power state with a certain type and use
that type to decide on what state to select. On r6xx+, we
select a state and then transition between clock modes in that
state. On pre-r6xx, we transition between states directly.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The general idea is to validate the current hw state
against the set of power states and select a power
state based on that. This patch just pulls the power
states from the bios and prints the information. It
is not currently hooked up in the actual power management
code. Hooking it up will require reworking the the current
power state selection code and will be handled in a future
patch.
Additionally, we'd need to decide on some default lower
power states for cards without power tables.
v2 - increment state_index after checking for default state
v3 - fix typo in pm init on pre-atom cards, handle pre-atom
cards without x86 bioses
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher