Variable 'n' in 'mt7621_pcie_init_virtual_bridges' function
can be directly initialized when it is declared instead of
doing it before using it first.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200413155018.31921-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a comment explaining a bit what is going on in this function.
It would be helfulp for other people for a better understanding
of the code.
Suggested-by: NeilBrown <neil@brown.name>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200413155018.31921-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Definition 'PCIE_P2P_MAX' is '3'. The value here is not a MAXimum.
It is a count or a number. It is how many masks there are.
The masks are numbered 0, 1, 2 so the maximum is 2. Hence rename
variable into 'PCIE_P2P_CNT' which is a more accurate name.
Suggested-by: NeilBrown <neil@brown.name>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200413155018.31921-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MT7621 has three assigned interrupts for the pcie. This
interrupts should properly being mapped taking into account
which devices are finally connected in which bus according
to link status. So the irq mappings should be as follows
according to link status (three bits indicating which devices
are link up):
* For PCIe Bus 1 slot 0:
- status = 0x2 || status = 0x6 => IRQ = pcie1_irq (24).
- status = 0x4 => IRQ = pcie2_irq (25).
- default => IRQ = pcie0_irq (23).
* For PCIe Bus 2 slot 0:
- status = 0x5 || status = 0x6 => IRQ = pcie2_irq (25).
- default => IRQ = pcie1_irq (24).
* For PCIe Bus 2 slot 1:
- status = 0x5 || status = 0x6 => IRQ = pcie2_irq (25).
- default => IRQ = pcie1_irq (24).
* For PCIe Bus 3 any slot:
- default => IRQ = pcie2_irq (25).
Because of this, the function 'of_irq_parse_and_map_pci' cannot
be used and we need to change device tree information from using
the 'interrupt-map' and 'interrupt-map-mask' properties into an
'interrupts' property to be able to get irq information from the
ports using the 'platform_get_irq' and storing an 'irq-map' into
the pcie driver data node to properly map correct irq using a
new 'mt7621_map_irq' function where this map will be read and the
correct irq returned.
Fixes: 46d093124d ("staging: mt7621-pci: improve interrupt mapping")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200413055942.2714-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pcie phy for pcie0 and pcie1 is shared using a dual ported
one. Current code was assuming that if nothing is connected
in pcie0 it won't be also nothing connected in pcie1. This
assumtion is wrong for some devices such us 'Mikrotik rbm33g'
and 'ZyXEL LTE3301-PLUS' where only connecting a card to the
second bus on the phy is possible. For such devices kernel
hangs in the same point because of the wrong poweroff of the
phy getting the following trace:
mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[hangs]
The wrong assumption is located in the 'mt7621_pcie_init_ports'
function where we are just making a power off of the phy for
slots 0 and 2 if nothing is connected in them. Hence, only
poweroff the phy if nothing is connected in both slot 0 and
slot 1 avoiding the kernel to hang.
Fixes: 5737cfe87a ("staging: mt7621-pci: avoid to poweroff the phy for slot one")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200409111652.30964-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting up kernel resource 'iomem_resource' for PCI with
addresses parsed from device tree gots into a conflict within
the usb xhci driver:
xhci-mtk 1e1c0000.xhci: can't request region for resource [mem 0x1e1c0000-0x1e1c0fff]
xhci-mtk: probe of 1e1c0000.xhci failed with error -16
Don't assign it and maintain the default addresses for this
resource seems to fix the problem. Checking legacy driver it
is being only setting the 'ioport_resource'.
Fixes: 09dd629eea ("staging: mt7621-pci: fix io space and properly set resource limits")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200322072128.4454-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Macro builtin_platform_driver can be used for builtin drivers
that don't do anything in driver init. So, use the macro
builtin_platform_driver and remove some boilerplate code.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200321133624.31388-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Making gpio8 and gpio9 vendor specific and putting them
into the specific dts file makes not needed to release
gpios anymore because we are not occupying those pins
in the first place if it is not necessary. When the
device tree is parsed we can also check and return for
the error because we rely in the fact that the related
device for the board is correct.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200321072650.7784-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function 'devm_gpiod_get_index_optional' returns NULL if the
descriptor is invalid and the error associated for the error
pointer is ENOENT. Sometimes if the pin is just assigned the
error associated for the pointer might not be ENOENT but other.
In order to avoid weirds behaviours if this happen set descriptor
to NULL in the driver port structure.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200320110123.9907-6-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are using the counter to print the slot which has been
enabled. Use the correct associated slot for the port instead.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200320110123.9907-5-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to align work with the mt7621-pci-phy part of
the driver and device tree which is now using only two
real phys one of them dual ported properly parse the
device tree and don't call phy initialization for the
slot 1 because is being taking into account when the
phy for the slot 0 is instantiated.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200320110123.9907-4-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some platforms gpio's are not used for reset but
for other purposes. Because of that when we try to
get them are valid gpio's but are already assigned
to do other function. To avoid those kind of problems
in those platforms just notice the fail in the kernel
but continue doing normal boot.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200319161416.19033-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of being using PCI Configuration and Status Register to
set up virtual bridges we are using CONFIG_ADDR Register which is
wrong. Hence, set the correct value.
Fixes: 9a5e71a68d ("staging: mt7621-pci: simplify 'mt7621_pcie_init_virtual_bridges' function")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200319095733.1557-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function 'mt7621_pci_parse_request_of_pci_ranges' is using
'of_pci_range_to_resource' to get both mem and io resources.
Internally this function calls to 'pci_address_to_pio' which
returns -1 if io space address is an address > IO_SPACE_LIMIT
which is 0xFFFF for mips. This mt7621 soc has io space in physical
address 0x1e160000. In order to fix this, overwrite invalid io
0xffffffff with properly values from the device tree and set
mapped address of this resource as io port base memory address
calling 'set_io_port_base' function. There is also need to properly
setup resource limits and io and memory windows with properly
parsed values instead of set them as 'no limit' which it is wrong.
For any reason I don't really know legacy driver sets up mem window
as 0xFFFFFFFF and any other value seems to does not work as expected,
so set up also here with same values.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200318094445.19669-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After review all the resets at the beggining the function
'mt7621_reset_port' is not needed anymore. Hence delete it
and its uses.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200313200913.24321-7-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
R3G's LEDs fail to initialize because one of them uses GPIO8
Hence, release the GPIO resources after PCIe initialization
and properly release also in driver error path.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200313200913.24321-6-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly update bindings documentation with added 'reset-gpios'
property. Delete also 'perst-gpio' which is not being used anymore.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200313200913.24321-5-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Value of 'PERST_DELAY_MS' is too high and it is ok just
to set up to 100 ms. Update also define name from
'PERST_DELAY_US' into 'PERST_DELAY_MS'
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200313200913.24321-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Original driver code was using three gpio's for reset
asserts and deasserts the pcis. Instead of using that
a general reset control with a perst gpio was introduced
and it seems it is partially working but sometimes there
are some unexpected hangs on boot. This commit make use of
the three original gpios using 'reset-gpios' property of
the device tree and removes the reset line and perst gpio.
According to the mediatek aplication note v0.1 there are
three gpios used for pcie ports reset control: gpio#19,
gpio#8 and gpio#7 for slots 0, 1 and 2 respectively.
This schema can be used separately for mt7621A but in some
boards due to pin share issue, if the PCM and I2S function
are enable at the same time, there are no enough GPIO to
control per-port PCIe reset. In those cases gpio#19 is enought
for reset the three ports together. Because of this we just
try to get the three gpios but if some of them fail we are not
failing in boot process, just prints a kernel notice and take
after into account if the descriptor is or not valid in order
to use it. All of them are set as GPIO output low configuration.
The gpio descriptor's API takes device tree property into account
and invert value if the pin is configured as active low.
So we also have to properly request pins from device tree
and set values correct in assert and deassert functions.
After this changes the order to make all assert and
deassert in the 'probe' process makes more sense:
* Parse device tree.
* make assert of the RC's and EP's before doing anything else.
* make deassert of the RC's before initializing the phy.
* Init the phy.
* make deassert of the EP's before initialize pci ports.
* Normal PCI initialization.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200313200913.24321-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clock related code concerns me from the very beginning because
there are some set ups got from legacy driver that are not documented
anywhere. According to the programming guide 0x7c is 'CPE_ROSC_SEL1'
register and 0x80 is 'CPU_CPE_CN'. I do think this set up is not needed
at all and the proper thing to do is just enable the clock bit for each
pcie port. Hence remove useless code and do the right thing which is
setting up the clock bit for each port enabled.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200310113459.30539-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function 'mt7621_pcie_init_virtual_bridges' is a bit mess and can be
refactorized properly in a cleaner way. Introduce new 'pcie_rmw' inline
function helper to do clear and set the correct bits this function needs
to work.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200308091928.17177-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some versions of SoC MT7621 have three PCI express hosts. Some boards
make use of those PCI through the staging driver mt7621-pci. Recently
PCI support has been removed from MT7621 Soc kernel configuration due
to a build error. This makes imposible to compile staging driver and
produces a regression for gnubee based boards. Enable support for PCI
again but enable it only if staging mt7621-pci driver is selected.
Fixes: c4d48cf5e2 ("MIPS: ralink: deactivate PCI support for SOC_MT7621")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: john@phrozen.org
Cc: NeilBrown <neil@brown.name>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20191019081233.7337-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on revision of the chip, reset lines are inverted. Make code
more readable making use of 'soc_device_match' in driver probe function.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20191006181032.19112-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function 'mt7621_pcie_request_resources' is using 'err'
local variable to get value returned from 'devm_request_pci_bus_resources'
and returning after that. This is not needed at all. Instead of that
just directly return returned value by the function which is also
returning zero on success.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20190720072908.16795-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return in two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190716055944.3237-1-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing parenthesis to PCIE_FTS_NUM_LO macro to do the
same it was being done in original code.
Fixes: a4b2eb912b ("staging: mt7621-pci: rewrite RC FTS configuration")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has dependencies on mt7621-gpio and mt7621-pci-phy which
are init in later stages. Hence, when this driver is probed it is always
returning 'EPROBE_DEFER' and being initialized afterwards. Use function
'module_init' to just initialize later.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing call to 'phy_exit' function if the phy_power_on call fails.
With this call added the error path is properly handled.
Fixes: 07420a02b0 ("staging: mt7621-pci: use gpio perst instead of builtin behaviour")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there is no pcie link detected we have to properly disable the
port pcie clock.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both driver and device tree have been updated to use GPIO perst.
Update bindings documentation also.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some boards seems to ignore the PERST builtin behaviour to properly
perform a pcie line reset. Use gpio PERST behaviour instead which
seems to be more common.
Fixes: bd1a05bd87 ("staging: mt7621-pci: use PERST_N instead of gpio control")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two messages in driver code which are not correct.
Fix both of them to clarify boot runs.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few remaining drivers/staging/*/Makefile files that do not
have SPDX identifiers in them. Add the correct GPL-2.0 identifier to
them to make scanning tools happy.
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few remaining drivers/staging/*/Kconfig files that do not
have SPDX identifiers in them. Add the correct GPL-2.0 identifier to
them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove comparison to NULL in the if statement expression
to match the Linux Kernel coding style.
CHECK: Comparison to NULL could be written "res"
Signed-off-by: Branden Bonaby <brandonbonaby94@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each enabled port is being checked in 'mt7621_pcie_enable_ports"
function calling 'mt7621_pcie_enable_port'. The return value for
this function on success is zero, so the check is reversed. Fix it.
Fixes: 802a2f7b2fe3: staging: mt7621-pci: factor out 'mt7621_pcie_enable_port' function
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to write IO and memory space window Host PCI bridge
registers before doing anything else. Just use its default values which
should be ok.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To properly follow kernel style replace spaces with tabs in comment
where link status bits are explained.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two definitions which are not being used at all.
Remove them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is still a reset line which is not being handled using reset_control
properly and just being accessing writing registers. Use reset_control
instead for pcie general reset line.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the things included in driver's TODO file have
been properly achieved. Update file accordly.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers can be useful on other MT76xx SoCs, which have compatible
peripherals. The drivers were selectable in Kconfig, but they were
quietly excluded from the build because the SOC_MT7621 chip was not
selected. So, make the Makefiles use the same flags as Kconfig for
these drivers.
mt7621-dma and mt7621-dts are left alone because they truly do require
that SoC.
I have personally confirmed that the mt7621-spi driver works on the
MT7688, which was what prompted this change.
Cc: linux-kernel@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: NeilBrown <neil@brown.name>
Cc: sergio.paracuellos@gmail.com
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seting up ports to enable PCI_COMMAND_MASTER is using '0x4' as a
hardcore value and '0x4' also for PCI_COMMAND register instead
of use definitions from linux pci system headers. Replace both.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Phy part of this driver has been moved to a new 'pci-mt7621-phy' driver.
Change code to use kernel's generic phy API removing also no more need
moved code.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid people reading this code being very confused, add a comment
clarifying the need for invert resets on some chip revisions.
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Abheek Dhawan