commit f54edb539c ("usb: dwc3: core: initialize ULPI before trying to
get the PHY") moved call to dwc3_core_get_phy() from dwc3_probe() to
dwc3_core_init() after dwc3_core_soft_reset(). But
dwc3_core_soft_reset() calls phy_init(), therefore dwc3_core_get_phy()
needs to be called before dwc3_core_soft_reset().
Fix this by moving call to dwc3_core_get_phy() before
dwc3_core_soft_reset().
This fixes the following abort seen on DRA7xx platforms
[ 24.769118] usb usb2: SerialNumber: xhci-hcd.1.auto
[ 24.781144] hub 2-0:1.0: USB hub found
[ 24.787836] hub 2-0:1.0: 1 port detected
[ 24.809939] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If don't reorder initialization like this, we will never be able to
get a reference to ULPI PHYs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If dr_mode is "otg" then support dual role mode of operation.
Currently this mode is only supported when an extcon handle is
present in the dwc3 device tree node. This is needed to
get the ID status events of the port.
We're using a workqueue to manage the dual-role state transitions
as the extcon notifier (dwc3_drd_notifier) is called in an atomic
context by extcon_sync() and this doesn't go well with
usb_del_gadget_udc() causing a lockdep and softirq warning.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can't have both Host and Peripheral roles active at the same time
because of one detail on DWC3: it shares the same memory area for both
Host and Peripheral registers.
When swapping roles we must reinitialize the new role every
time. Let's make sure this works for our debugfs interface.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We're going to use this member to track which role we're currently
playing, that way we can more easily implement dual-role swap in
upcoming patches.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
- DWC_USB3_NUM indicates the number of Device mode single directional
endpoints, including OUT and IN endpoint 0.
- DWC_USB3_NUM_IN_EPS indicates the maximum number of Device mode IN
endpoints active at any time, including control endpoint 0.
It's possible to configure RTL such that DWC_USB3_NUM_EPS is equal to
DWC_USB3_NUM_IN_EPS.
dwc3-core calculates the number of OUT endpoints as DWC_USB3_NUM minus
DWC_USB3_NUM_IN_EPS. If RTL has been configured with DWC_USB3_NUM_IN_EPS
equal to DWC_USB3_NUM then dwc3-core will calculate the number of OUT
endpoints as zero.
For example a from dwc3_core_num_eps() shows:
[ 1.565000] /usb0@f01d0000: found 8 IN and 0 OUT endpoints
This patch refactors the endpoint calculation down to one variable
dwc->num_eps taking care to maintain the current mapping of endpoints for
fixed FPGA configurations as described in Table 4-7 of version 2.60a of the
DWC USB3 databook.
The endpoint mapping will then be EP-OUT, EP-IN etc, up to DWC_USB3_NUM.
If DWC_USB3_NUM is odd then OUT will take the extra endpoint.
Suggested-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This bit is only supposed to be used with known
buggy PHYs, however some platforms might erroneously
set it. In order to avoid it, let's make sure this
bit is always cleared. If some PHY needs this, we
will need to add a quirk flag.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
The dma ops for dwc3 devices are not set properly. So, use a
physical device sysdev, which will be inherited from parent,
to set the hardware / firmware parameters like dma.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is a workaround for STAR 9000961433 which affects only version
3.00a of the DWC_usb3 core. This prevents the controller interrupt from
being masked while handling events. Enabling interrupt moderation allows
us to work around this issue because once the GEVNTCOUNT.count is
written the IRQ is immediately deasserted and won't be asserted again
until GEVNTCOUNT.EHB is cleared.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implement interrupt moderation which allows the interrupt rate to be
throttled. To enable this feature the dwc->imod_interval must be set to
1 or greater. This value specifies the minimum inter-interrupt interval,
in 250 ns increments. A value of 0 disables interrupt moderation.
This applies for DWC_usb3 version 3.00a and higher and for DWC_usb31
version 1.20a and higher.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This extra buffer will be used so we can copy
triggered events from our event buffer to this cache
and process all of them later in bottom half
handler.
We need this in order to implement a workaround for
a known erratum in recent DWC3 release.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_soft_reset() is doing the same thing as
dwc3_core_soft_reset(). Let's remove
dwc3_soft_reset() since that's not needed anymore.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a function to check properties and call it from probe. This will
allow us to add check code without bloating the probe function. This
needs to be done after dwc3_get_properties() and dwc3_core_init() so
that all the properties and hardware configs are available.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Finally get rid of dwc3_trace() hack. If any other
message is truly needed, we should add proper
tracepoints for them instead of hacking around with
dwc3_trace() or similar.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This helper will be responsible for reading and
parsing our properties. No functional changes in
this patch, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This little helper will be used to setup anything
related to GCTL register. There are no functional
changes, this is a cleanup only patch.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This little helper will be used to make sure we're
dealing with a valid Synopsys DWC3 or DWC3.1 core.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For the usb31 IP and from version 2.90a of the usb3 IP, the core
supports HW exit from L1 in HS. Enable it, otherwise the controller may
never exit from LPM to do a transfer.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Member @mem in struct dwc3 is not used in any places. Clean up it.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
-----BEGIN PGP SIGNATURE-----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=vTFa
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.9 merge window
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
This patch follows the similar fix in dwc2. See
commit 5268ed9d2e ("usb: dwc2: Fix dr_mode validation")
Currently, the dr_mode is only checked against the module configuration.
It also needs to be checked against the hardware capablities.
The driver now checks if both the module configuration and hardware are
capable of the dr_mode value. If not, then it will issue a warning and
fall back to a supported value. If it is unable to fall back to a
suitable value, then the probe will fail.
Behavior summary:
module : actual
HW config dr_mode : dr_mode
---------------------------------
host host any : host
host dev any : INVALID
host otg any : host
dev host any : INVALID
dev dev any : dev
dev otg any : dev
otg host any : host
otg dev any : dev
otg otg any : dr_mode
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].
This feature is NOT available on the DWC_usb31 (USB 3.1) IP.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When dwc3 core enters into suspend mode, the system (especially for mobile
device) may power off the dwc3 controller for power saving, that will cause
dwc3 controller lost the mode operation when resuming dwc3 core.
Thus we can move the mode setting into dwc3_core_init() function to avoid this
issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.
But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After going through runtime_suspend/runtime_resume
cycle once we would be left with an unbalanced
pm_runtime_get() call. Fix that by making sure that
we try to suspend right after resuming so things are
balanced and device can runtime_suspend again.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implementations might use different IRQs for
host, gadget so use named interrupt resources
to allow device tree to specify the interrupts.
Following are the interrupt names
Peripheral Interrupt - peripheral
HOST Interrupt - host
Maintain backward compatibility for a single named
interrupt ("dwc3_usb3") for all interrupts as well as
unnamed interrupt at index 0 for all interrupts.
As platform_get_irq() variants are used, tackle
the -EPROBE_DEFER case as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If there is a failure after pm_runtime_enable/get_sync()
we need to call pm_runtime_disable/put_sync().
Otherwise it will lead to an unbalanced pm_runtime_enable() on the
subsequent probe if the earlier probe bailed out due to -EPROBE_DEFER.
pm_runtime_get_sync() can fail as well so deal with that case too.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We shouldn't change a host-only dwc3 to gadget-only
if driver is built as gadget-only. Fix that up here.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No more users for it.
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this patch implements the most basic pm_runtime
support for dwc3. Whenever USB cable is dettached,
then we will allow core to runtime_suspend.
Runtime suspending will involve completely tearing
down event buffers and require a full soft-reset of
the IP.
Note that a further optimization could be
implemented once we decide to support hibernation,
which is to allow runtime_suspend with cable
connected when bus is in U3. That's subject to a
separate patch, however.
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
now that we have re-factored dwc3_core_init() and
dwc3_core_exit() we can use them for suspend/resume
operations.
This will help us avoid some common mistakes when
patching code when we have duplicated pieces of code
doing the same thing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The idea of this patch is for dwc3_core_init() to
abstract all the details about how to initialize
dwc3 and dwc3_core_exit() to do the same for
teardown.
With this, we can simplify suspend/resume operations
by a large margin and always know that we're going
to start dwc3 from a known starting point.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this patch is in preparation for some further
re-factoring in dwc3 initialization. No functional
changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7szP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.7 merge window
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
this helper will be used, initially, to dump space
of different queues and fifos in dwc3 to
debugfs. Later, it'll be used to issue remote wakeup
when we want to start a transfer and there's
something in a TX FIFO.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Debugfs init failure is not so important. We can continue our job on
this failure. Also no break need for debugfs_create_file call failure.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[felipe.balbi@linux.intel.com :
- remove out-of-memory message, we get that from OOM.
- switch dev_err() to dev_dbg() ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we need to power off the PHY during suspend and
power it back on during resume.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: fix call to usb_phy_set_suspend() in dwc3_suspend()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be using a single event buffer and that
renders ev_buffs array unnecessary. Let's remove it
in favor of a single pointer to a single event
buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We never, ever route any of the other event buffers
so we might as well drop support for them.
Until someone has a real, proper benefit for
multiple event buffers, we will rely on a single
one. This also helps reduce memory footprint of
dwc3.ko which won't allocate memory for the extra
event buffers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16f8 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook, we shouldn't be
relying on GCTL.CORESOFTRESET bit as that's only for
debugging purposes. Instead, let's use DCTL.CSFTRST
if we're OTG or PERIPHERAL mode.
Host side block will be reset by XHCI driver if
necessary. Note that this reduces amount of time
spent on dwc3_probe() by a long margin.
We're still gonna wait for reset to finish for a
long time (default to 1ms max), but tests show that
the reset polling loop executed at most 19 times
(modprobe dwc3 && modprobe -r dwc3 executed 1000
times in a row).
Suggested-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Vignesh R